Capacity ManagementService
Edge-Fiber Node Management
November 2013
DTI Expertise for end-to-end success
Agenda• Introductions
• Edge-Fiber Node Capacity Management Practices and Challenges
• Overview of Methodology, Data Inputs being utilized, and their inherent deficiencies
• Description of Various development efforts
• Discussion around R&D effort and findings
• Q & A
• Next Steps
DTI Expertise for end-to-end success
What is needed in Capacity Planning
• A better, faster, more efficient way to handle your HSD Capacity Engineering
• Get it right the first time
• Engineer your network faster
• Engineer your network more effectively
• More efficient utilization of existing resources
DTI Expertise for end-to-end success
Leverage tools and expertise
• MSO are utilizing tools that allow for better:• Hardware Utilization – Level Load your CMTS
• Manpower Effectiveness – Augment once
• Provide reports/data for more effective planning for the HSD Network – Know what will happen when
• Automate the Mundane Tasks
DTI Expertise for end-to-end success
Edge-Fiber Node Management Challenges
• Basic Practices–NCP Creation is Based on Nodal Modem Counts (Auspice)
–Time Consuming, tedious, often obsolete before its implemented
–Fundamental flaw, node and port splits are based on Modem counts and not actual usage
DTI Expertise for end-to-end success
Edge-Fiber Node Management Challenges • Problems With Today’s Basic Practices
–NCP Creation is Based on Nodal Modem Counts (Auspice)– Users/modems do not operate on the basic law of averages but rather at best case resembles a Log Normal Distribution or, most likely behave
more in line with a Power Law probability distribution pattern
–Time Consuming, tedious, often obsolete before its implemented– When splitting nodes there is no way to determine nodal contribution to port utilization
– Prone to human error, large spreadsheets lots of room for mistakes
–Fundamental flaw, node and port splits are based on Modem counts and not actual usage
DTI Expertise for end-to-end success
Port Utilization vs. Modem Counts
• DS Port # 2 (bar 3) illustrates that DS Port Utilization is not necessarily proportional to Modem Counts. • Comparing DS Ports #0 (bar 1) and #1 (bar 2) illustrates that growth and the magnitude of weekly
variations in DS Port Utilization are also not necessarily proportional to Modem Counts.• This data is straight from the NCP and Weekly Capacity Utilization Reports.
DTI Expertise for end-to-end success
What does Port Utilization Forecasting Mean
DTI Expertise for end-to-end success
Actual Results: CMTS Port Utilization
UTallest = 74%
UTallest = 45%
Customer’s Initial NCP
Customer’s Next NCP
DTI’s Optimization of the Customer’s Initial NCP using the Customer’s initial number of DS Ports
• The same amount of CMTS hardware is used in the middle and bottom charts, but the bottom NCP would last more than 5.8 times longer.
DTI Expertise for end-to-end success
Comparison of DS Port Loading (Top) Customer’s Initial NCP (Middle) Customer’s Next NCP(Bottom) DTI’s Optimization of the Customer’s Initial NCP (using Customer’s Initial NCP’s 6 DS Ports)
UTallest = 74%
UTallest = 57%
Customer’s Initial NCP
Customer’s Next NCP
DTI’s Optimization of the Customer’s Initial NCP using the Customer’s initial number of DS Ports
DTI Expertise for end-to-end success
The Win• Improve Customer Satisfaction
• Less often augmentations less down time for your customers• Better balanced CMTS and edge elements results in less over-utilized ports offering
better throughput to your customers
• Reduce Engineering/Field Cycles• Turnaround of NCP Designs in 1-2 days from 3-5 days• Extending the time between augmentations
• Targeting Hardware Utilization• More efficiently engineered CMTS and edge systems. • Develop NCPs that more equally distribute utilization across all ports, lowering the
number of underutilized resources/ports
• Supports field standardization
DTI Expertise for end-to-end success
Top Related