2 1
140G-R
Bul. 140G
DIR 1000650R0611 Version 00
WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants. (Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden.
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée. Protéger le produit contre les environnements agressifs.
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada. Manténgalo libre de contaminantes.
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes.
Installation - Installazione - Instalación Instalação - -
DIR 1000650R0611 Version 00 - PN-387658
警告:感電事故防止のため、取付けまたは修理の際は電源から取り外してください。適切なケース内に取付けてください。また、汚染物質がないことを確認してください。
警告:为了防止触电,在安装或维修之前必须先切断电源。安装在合适的设备箱内。防止接触污染 。物
Kirk lock installation kit for 140G-RKit installazione blocco KirkSatz Installation verriegelung KirkKit installation verrouillage KirkKit instalación bloqueo Kirk
Retaining ring
Lock adapter
CamCover Self-tapping screw
Support assembly SlideCap
dia.LENGTH 312 mm (0.47”)
Required tool
xx lb-inxx Nm
1
2
(2)DIR 1000650R0611 Version 00
Kirk SD series cam lock purchased separately for customer installation
31
32
2
34
3
4
(3)DIR 1000650R0611 Version 00
3
if presentif present do not remove, dispose of coversupplied with this kit
5
6
(4)DIR 1000650R0611 Version 00
1
2
2
1
if not present, use the cover supplied with this kit
Cover
#1 10-15 lb-in (1.2-1.7 Nm)
7
8
(5)DIR 1000650R0611 Version 00
1
4
3
4
2
#1 10-15 lb-in (1.2-1.7 Nm)
2
1
Key lock operating procedure:1 - Push and keep pushed the open button.2 - Turn the key counter-clockwise in horizontal position.3 - Pull off the key.4 - Release the open button.
DIR 1000650R0611 Version 00 - B0767 Copyright © 2017 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 140G-IN148A-MU-P - May 2017
Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page
9
3
Page 1Page 2Page 3Page 4Page 5Page 6
MATERIALSIZE
FOLD
TO BE DETERMINEDBY STRATEGIC PARTNER
TO BE DETERMINEDBY STRATEGIC PARTNER
TO BE DETERMINEDBY STRATEGIC PARTNER
FLAT
This Instruction Sheet is Being Printed by Strategic Partner
Note: After folding---Printed in (Country where printed)* and instruction sheet number in lower left corner should be visible.
* The printing vendor may change the instruction sheet files to show the correct country.
Top Related