BUCKLING, POSTBUCKLING AND PROGRESSIVE FAILURE ANALYSIS OF HYBRID COMPOSITE SHEAR WEBS USING A CONTINUUM DAMAGE MECHANICS MODEL
A Dissertation by
Javier Herrero
Master of Science, Wichita State University, 2000
Aeronautical Engineer, Polytechnic University of Madrid, 1997
Submitted to the Department of Aerospace Engineering and the faculty of the Graduate School of
Wichita State University in partial fulfillment of
the requirements for the degree of Doctor of Philosophy
December 2007
© Copyright 2007 by Javier Herrero
All Rights Reserved
iii
BUCKLING, POSTBUCKLING AND PROGRESSIVE FAILURE ANALYSIS OF HYBRID COMPOSITE SHEAR WEBS USING A CONTINUUM DAMAGE MECHANICS MODEL
The following faculty have examined the final copy of this dissertation for form and content, and recommend that it be accepted in partial fulfillment of the requirement for the degree of Doctor of Philosophy with a major in Aerospace Engineering
__________________________ Charles Yang, Committee Chair ____________________________ James Locke, Committee Member ____________________________ Walter Horn, Committee Member _____________________________ John Tomblin, Committee Member _______________________________ Hamid Lankarani, Committee Member
Accepted for the College of Engineering _____________________________ Zulma Toro-Ramos, Dean Accepted for the Graduate School _______________________________ Susan Kovar, Dean
iv
DEDICATION
To my dear wife, Melissa, and my joyful children, Grant and Isabel, for their silent sacrifices
v
ACKNOWLEDGEMENTS
I would like to thank my advisors, James Locke and Charles Yang, for their many years
of thoughtful, patient guidance and support. I also thank Ismael Heron for his generous advice
and coaching, and to my friend and mentor Everett Cook. I would also like to extend my
gratitude to the members of my committee Walter Horn, John Tomblin, Bert Smith and Hamid
Lankarani. I also want to thank to the Sandia National Laboratories for funding the experimental
portion of this research, to Juan Felipe Acosta, Tom Hermann and Sanjay Sharma of the National
Institute for Aviation Research for their cooperation, and to Tai Vuong of the Boeing Company
for his technical remarks to my work.
vi
ABSTRACT
This dissertation presents an innovative analysis methodology to enhance the design of
composite structures by extending their work range into the postbuckling regime. This objective
is accomplished by using the numerical simulation capabilities of nonlinear finite element
analysis combined with continuum damage mechanics models to simulate the onset of failure
and the subsequent material properties degradation. A complete analysis methodology is
presented with increasing levels of complexity. The methodology is validated by correlation of
analytical results with experimental data from a set of hybrid carbon/epoxy glass/epoxy
composite panels tested under shear loading using a picture frame fixture.
TABLE OF CONTENTS
Chapter Page
vii
1 INTRODUCTION ........................................................................................................................1
2 OVERVIEW OF BUCKLING, POSTBUCKLING AND PROGRESSIVE FAILURE..............7
2.1 General requirements and key features of the analysis and simulation ......................7
2.2 Preliminary observations about nonlinearity, buckling and post-buckling ................9
2.3 Linearized buckling solution.....................................................................................11
2.4 Nonlinear solution.....................................................................................................12
2.5 Mode-based failure criteria and progressive failure analysis ...................................14
3 LITERATURE REVIEW ...........................................................................................................16
4 SCOPE AND OBJECTIVES......................................................................................................24
5 EXPERIMENTAL STUDY........................................................................................................27
5.1 Data reduction of strain gage readings......................................................................28
5.2 Data reduction of the ARAMIS optical system measurements ................................35
5.2.1 Laminate G - 20 degree data reduction..........................................................36
5.2.2 Laminate H - 45 degree data reduction..........................................................41
5.2.3 Laminate E - 90 degree data reduction ..........................................................46
5.2.4 Laminate F - 0 degree data reduction ............................................................51
5.3 Comparison plot of ARAMIS data vs. strain gage data............................................54
5.4 Experimental determination of buckling loads. Spencer-Walker method ................58
TABLE OF CONTENTS (continued)
Chapter Page
viii
5.4.1 Southwell plots for struts under compression................................................58
5.4.2 Spencer-Walker plots for plates.....................................................................60
5.4.3 Spencer-Walker plots for the panels tested....................................................62
6 FINITE ELEMENT MODEL.....................................................................................................68
6.1 Modeling the composite panels ................................................................................70
6.2 Modeling the picture frame arms..............................................................................71
6.3 Mechanical properties of the laminates tested ..........................................................72
7 ANALYTICAL CLASSICAL SOLUTIONS.............................................................................75
8 LINEARIZED BUCKLING ANALYSIS ..................................................................................89
8.1 Formulation...............................................................................................................89
8.2 Analysis results .........................................................................................................90
8.2.1 Laminate F - 0 degree with the direction of the load.....................................91
8.2.2 Laminate G – 20 degree with the direction of the load..................................94
8.2.3 Laminate H – 45 degree with the direction of the load..................................97
8.2.4 Laminate E – 90-degree with the direction of the load................................100
8.2.5 Linearized buckling analysis. Summary of results. .....................................103
9 NONLINEAR BUCKLING AND POSTBUCKLING (WITHOUT FAILURE) ....................107
9.1 Formulation.............................................................................................................107
TABLE OF CONTENTS (continued)
Chapter Page
ix
9.1.1 Historical approaches...................................................................................107
9.1.2 Time approximation and Newton-Raphson method ....................................109
9.2 Effect of initial imperfections in the nonlinear solution .........................................112
9.2.1 Effects of initial imperfections in the ANSYS model .................................112
9.2.2 Effects of initial imperfections in the ABAQUS model ..............................116
9.3 Effect of the sub-stepping in the solution ...............................................................118
9.4 Correlation of FE model strains with strain gage readings.....................................118
9.4.1 Laminate G – 20 degree with the direction of the load................................123
9.4.2 Laminate H – 45 degree with the direction of the load................................127
9.4.3 Laminate E – 90 degree with the direction of the load ................................130
9.4.4 Laminate F – 0 degree with the direction of the load ..................................133
10 PROGRESSIVE FAILURE ANALYSIS...............................................................................137
10.1 Failure prediction in the analysis of deeply postbuckled panels.............................137
10.1.1 Material nonlinearities .................................................................................138
10.1.2 Delamination growth and decohesion elements ..........................................139
10.2 Overview of the progressive failure analysis (PFA)...............................................139
10.3 Failure Criteria. Damage activation functions ........................................................140
10.4 Material degradation model in the FE simulation...................................................144
TABLE OF CONTENTS (continued)
Chapter Page
x
10.4.1 Damage initiation.........................................................................................144
10.4.2 Evolution of the damage variables for each mode.......................................145
10.4.3 Maximum degradation and element removal ..............................................151
10.4.4 Viscous regularization algorithm.................................................................152
10.5 Results of the nonlinear model with progressive failure analysis...........................155
10.5.1 Fiber tensile failure evolution ......................................................................156
10.5.2 Fiber compressive failure evolution.............................................................159
10.5.3 Matrix tensile failure evolution....................................................................161
10.5.4 Matrix compressive failure evolution ..........................................................164
10.6 Summary of results. Nonlinear model with progressive failure analysis ...............170
10.7 Comparison of the Hashin’s failure functions with other failure criteria ...............172
11 CONCLUSIONS AND RECOMENDATIONS.....................................................................177
12 REFERENCES .......................................................................................................................185
LIST OF FIGURES
Figure Page
xi
1. Figure 1.1 Rectangular isotropic plate subjected to pure shear stresses [2] .......................2
2. Figure 1.2 Kuhn’s diagonal-tension beam..........................................................................3
3. Figure 2.1 Response of a thin plate or shell under out-of-plane loading............................9
4. Figure 2.2 Schematic nonlinear versus linearized responses............................................11
5. Figure 2.3 Newton-Raphson limitation (left) and Arc-Length methodology (right)........13
6. Figure 5.1 Schematic diagram of picture frame fixture and panel geometry. ..................27
7. Figure 5.2 Picture frame test setup. ..................................................................................29
8. Figure 5.3 Laminate 20 deg. Strains measured on the tension diagonal...........................30
9. Figure 5.4 Laminate 20 deg. Strains measured on the compression diagonal. .................30
10. Figure 5.5 Laminate 45 deg. Strains measured on the tension diagonal...........................31
11. Figure 5.6 Laminate 45 deg. Strains measured on the compression diagonal. .................31
12. Figure 5.7 Laminate 90 deg. Strains measured on the tension diagonal...........................32
13. Figure 5.8 Laminate 90 deg. Strains measured on the compression diagonal. .................32
14. Figure 5.9 Laminate 0 deg. Strains measured on the tension diagonal.............................33
15. Figure 5.10 Laminate 0 deg. Strains measured on the compression diagonal. .................33
16. Figure 5.11 Comparison of all laminates. Strains on tension diagonal, front face ...........34
17. Figure 5.12 Comparison of all laminates. Strains on compression diagonal, front face ..34
18. Figure 5.13 ARAMIS reference axes for strain measurement..........................................35
LIST OF FIGURES (continued)
Figure Page
xii
19. Figure 5.14 Laminate 20 deg, front face, out of plane displacement ( )lbsP 1.39746= . .36
20. Figure 5.15 Laminate 20 deg, front face, xxε strain, ( )lbsP 1.39746= ...........................36
21. Figure 5.16 Laminate 20 deg, front face, yyε strain, ( )lbsP 1.39746= ...........................37
22. Figure 5.17 Laminate 20 deg, front face, xyε strain, ( )lbsP 1.39746= ...........................37
23. Figure 5.18 xxε strains, compression diag., front face, different load levels. ..................38
24. Figure 5.19 xxε vs load, front face compression diag., around center of panel................38
25. Figure 5.20 yyε strains on the tension diagonal for different load levels. ........................39
26. Figure 5.21 yyε vs load - tension diagonal, locations around center of panel. .................40
27. Figure 5.22 Laminate 45 deg front face, out of plane displacement ( )lbsP 65.33139= .41
28. Figure 5.23 Laminate 45 deg, front face, xxε strain, ( )lbsP 65.33139= . .......................41
29. Figure 5.24 Laminate 45 deg, front face, yyε strain, ( )lbsP 65.33139= . .......................42
30. Figure 5.25 Laminate 45 deg, front face, xyε strain, ( )lbsP 65.33139= . .......................42
31. Figure 5.26 xxε strains on the compression diagonal for different load levels. ...............43
32. Figure 5.27 xxε vs load. Compression diag., locations around center of panel................43
33. Figure 5.28 yyε strains on the tension diagonal for different load levels. ........................44
34. Figure 5.29 yyε strains on the tension diagonal for different load levels. ........................45
LIST OF FIGURES (continued)
Figure Page
xiii
35. Figure 5.30 Laminate 90 deg front face, out of plane displacement ( )lbsP 9.31044= ...46
36. Figure 5.31 Laminate 90 deg, front face, xxε strain, ( )lbsP 4.23525= . .........................46
37. Figure 5.32 Laminate 90 deg, front face, yyε strains, ( )lbsP 9.31044= .........................47
38. Figure 5.33 Laminate 90 deg, front face, xyε strains, ( )lbsP 9.31044= .........................47
39. Figure 5.34 xxε on the compression diagonal for different load levels. ...........................48
40. Figure 5.35 xxε vs. load - compression diag., locations around center of panel. .............48
41. Figure 5.36 yyε on the tension diagonal for different load levels.....................................49
42. Figure 5.37 yyε on the tension diagonal for different load levels.....................................50
43. Figure 5.38 xxε on the compression diagonal for different load levels. ...........................51
44. Figure 5.39 xxε vs. load - compression diag., locations around center of panel. .............52
45. Figure 5.40 yyε strains on the tension diagonal for different load levels. ........................53
46. Figure 5.41 yyε strains on the tension diagonal for different load levels. ........................53
47. Figure 5.42 Lam 20 degree - strains measured at different locations of the tension and
the compression diagonal vs. actuator load. ARAMIS vs. strain gage..............................54
48. Figure 5.43 Laminate 45 degree - strains measured at different locations of the tension
and the compression diagonal vs. actuator load. ARAMIS vs. strain gage. ......................55
49. Figure 5.44 Laminate 90 degree - strains measured at different locations of the tension
and the compression diagonal vs. actuator load. ARAMIS vs. strain gage. ......................56
LIST OF FIGURES (continued)
Figure Page
xiv
50. Figure 5.45 Laminate 0 degree - strains measured at different locations of the tension and
the compression diagonal vs. actuator load. ARAMIS vs. strain gage..............................57
51. Figure 5.46 - Laminate F (0 degree): ARAMIS measured out of plane displacement vs.
load (above), and same data in Spencer-Walker format (below).......................................64
52. Figure 5.47 - Laminate G (20 degree): ARAMIS measured out of plane displacement vs.
load (above), and same data in Spencer-Walker format (below).......................................65
53. Figure 5.48 - Laminate H (45 degree): ARAMIS measured out of plane displacement vs.
load (above), and same data in Spencer-Walker format (below).......................................66
54. Figure 5.49 - Laminate E (90 degree): ARAMIS measured out of plane displacement vs.
load (above), and same data in Spencer-Walker format (below).......................................67
55. Figure 6.1 ABAQUS FE model view. Picture frame and panel .......................................69
56. Figure 6.2 ANSYS section plot of the laminate for the case of zero degree with the
direction of the load. ..........................................................................................................73
57. Figure 7.1 Laminate 0 degree. Lay-up and stiffness matrices ..........................................76
58. Figure 7.2 Laminate 20 degrees. Lay-up and stiffness matrices.......................................77
59. Figure 7.3 Laminate 45 degrees. Lay-up and stiffness matrices.......................................78
60. Figure 7.4 Laminate 90 degree. Lay-up and stiffness matrices ........................................79
61. Figure 7.5 Laminate 0 degree. Buckling load calculation, two-term Ritz approx............80
62. Figure 7.6 Laminate 20 degrees. Buckling load calculation, two-term Ritz approx. .......81
63. Figure 7.7 Laminate 45 degrees. Buckling load calculation, two-term Ritz approx. .......82
LIST OF FIGURES (continued)
Figure Page
xv
64. Figure 7.8 Laminate 90 degrees. Buckling load calculation, two-term Ritz approx. .......83
65. Figure 8.1 Laminate 0 degree, section plot.......................................................................92
66. Figure 8.2 First mode, buckling load lbsP 838,21= . Out of plane displacement ..........92
67. Figure 8.3 Second mode, buckling load lbsP 522,22= . Out of plane displacement......93
68. Figure 8.4 Third mode, buckling load lbsP 456,47= . Out of plane displacement ........93
69. Figure 8.6 First mode, buckling load lbsP 681,15= . Out of plane displacement ...........96
70. Figure 8.7 Second mode, buckling load lbsP 335,16= . Out of plane displacement ......96
71. Figure 8.8 Third mode, buckling load lbsP 489,34= . Out of plane displacement.........97
72. Figure 8.9 Laminate section plot. Lam 45 deg. ................................................................98
73. Figure 8.10 First mode, buckling load lbsP 498,9= . Out of plane displacement ..........99
74. Figure 8.11 Second mode, buckling load lbsP 147,10= . Out of plane displacement ....99
75. Figure 8.12 Third mode, buckling load lbsP 083,18= . Out of plane displacement .....100
76. Figure 8.13 Laminate section plot. Lam 90 deg. ............................................................101
77. Figure 8.14 First mode, buckling load lbsP 605,4= . Out of plane displacement ........102
78. Figure 8.15 Second mode, buckling load lbsP 865,5= . Out of plane displacement ....102
79. Figure 8.16 Third mode, buckling load lbsP 788,10= . Out of plane displacement .....103
80. Figure 8.17 Rotation of the buckling nodal line. Second mode......................................105
LIST OF FIGURES (continued)
Figure Page
xvi
81. Figure 8.18 Rotation of the buckling nodal lines. First mode ........................................106
82. Figure 9.1 Replication of the first mode with an out of plane perturbation force in the
middle node. Out of plane displacement plot. Laminate 0 degree...................................113
83. Figure 9.2 Replication of the second mode with a couple of perturbation forces, opposite
in sign on symmetric locations. Out of plane displacement plot. Lam 0 deg ..................114
84. Figure 9.3 Perturbation with a couple of forces to induce the second mode ..................115
85. Figure 9.4 Lam 20 deg ABAQUS strains in the first Gaussian integration point in front
and back layers of the laminate FE at the center of the panel..........................................117
86. Figure 9.5 Elements under the footprint of the strain gage. ABAQUS model mesh
element size 0.25 in, compressed diagonal front face .....................................................120
87. Figure 9.6 Integration points in ABAQUS S4 element, 3 per layer (nonlinear finite strain
laminated shell) ................................................................................................................120
88. Figure 9.7 Lam 20 deg ANSYS results. Normalized strains on compressed diagonal. .124
89. Figure 9.8 Laminate 20 deg ANSYS results. Normalized strains on tension diagonal. .124
90. Figure 9.9 Laminate 20 deg, ABAQUS results. Normalized strains on compressed
diagonal, on front and back faces. ...................................................................................125
91. Figure 9.10 Lam. 20 deg. Out of plane displacements on front face. Top to down:
ARAMIS surface readings, ANSYS results, ABAQUS results (5 mm = 0.1969 in) ......126
92. Figure 9.11 Lam 20 deg ANSYS. Normalized strains on compressed diagonal. ...........127
93. Figure 9.12 Lam 45 deg ANSYS. Normalized strains on tension diagonal. ..................128
94. Figure 9.13 Lam 45 deg, ABAQUS. Normalized strains critxx εε / on compressed
LIST OF FIGURES (continued)
Figure Page
xvii
diagonal on front and back faces. ....................................................................................128
95. Figure 9.14 Lam. 45 deg. Out of plane displ. on front face. Top to bottom: ARAMIS
surface readings, ANSYS and ABAQUS results (7 mm = 0.2756 in) ............................129
96. Figure 9.15 Lam 90 deg ANSYS. Normalized strains on compressed diagonal. ...........130
97. Figure 9.16 Lam 90 deg ANSYS. Normalized strains on tension diagonal. ..................131
98. Figure 9.17 Lam 90 deg, ABAQUS. Normalized strains on compressed diagonal, on
front and back faces. ........................................................................................................131
99. Figure 9.18 Laminate 90 degree. Out of plane displacement. Top to bottom: ARAMIS
surface readings, ANSYS results, ABAQUS results (12 mm = 0.4724 in).....................132
100. Figure 9.19 Lam 0 deg ANSYS. Normalized strains on compressed diagonal. .............133
101. Figure 9.20 Lam 0 deg ANSYS. Normalized strains on tension diagonal. ....................134
102. Figure 9.21 Laminate 0 deg, ABAQUS. Normalized strains on compressed diagonal, on
front and back faces. ........................................................................................................134
103. Figure 9.22 Laminate 0 degree. Out of plane displacement. (a) Nonlinear Analysis
ANSYS last load step. (b) Nonlinear Analysis ABAQUS last load step.........................135
104. Figure 10.2 Bilinear strain softening law in terms of equivalent magnitudes ................148
105. Figure 10.3 Damage variable as a function of equivalent displacement. .......................150
106. Figure 10.4 Effect of the viscous regularization coefficient in the nonlinear solution.
Strains on compressed diagonal at the center, front and back faces (20 degree panel) ...154
107. Figure 10.5 Fiber tensile failure index. First occurrence of damage, load step 9. Actuator
load ( )lbsP 799,13= .......................................................................................................157
LIST OF FIGURES (continued)
Figure Page
xviii
108. Figure 10.6 Fiber tensile failure index, load step 12, ( )lbsP 163,17= ..........................157
109. Figure 10.7 Fiber tensile failure index, load step 14, ( )lbsP 325,20= .........................158
110. Figure 10.8 Fiber tensile failure index, load step 15, ( )lbsP 465,27= .........................158
111. Figure 10.9 Fiber tensile failure index, load step 16, ( )lbsP 434,30= .........................159
112. Figure 10.10 Fiber compressive failure index, load step 14 ( )lbsP 325,20= ...............160
113. Figure 10.11 Fiber compressive failure index, load step 15, ( )lbsP 465,27= ..............160
114. Figure 10.12 Fiber compressive failure index, load step 16, ( )lbsP 433,30= ..............161
115. Figure 10.13 Matrix tensile failure. First occurrence of damage, load step 7. Actuator
load ( )lbsP 497,11= .......................................................................................................162
116. Figure 10.14 Matrix tensile failure, load step 12. ( )lbsP 163,17= ................................162
117. Figure 10.15 Matrix tensile failure, load step 14. ( )lbsP 325,20= ...............................163
118. Figure 10.16 Matrix tensile failure. End of step 15. ( )lbsP 465,27= ...........................163
119. Figure 10.17 Matrix tensile failure. End of step 16. ( )lbsP 434,30= ..........................164
120. Figure 10.18 Matrix compressive failure, load step 9 ( )lbsP 799,13= ..........................165
121. Figure 10.19 Matrix compressive failure, load step 12 ( )lbsP 163,17= .......................165
122. Figure 10.20 Matrix compressive failure, load step 14 ( )lbsP 325,20= ......................166
123. Figure 10.21 Matrix compressive failure, load step 15 ( )lbsP 465,27= ......................166
LIST OF FIGURES (continued)
Figure Page
xix
124. Figure 10.22 Matrix compressive failure, load step 16 ( )lbsP 433,30= ......................167
125. Figure 10.23 Matrix compr. failure, load step 14. Failure index at plies 1, 2, 3 & 4 .....168
126. Figure 10.24 Matrix compr failure load step 14. Failure index at plies 5, 6, 7 & 8 .......169
127. Figure 10.25 Strain on compression diagonal vs. actuator load with PFA results. ........171
128. Figure 10.26 Hashin’s failure indices, load step 14, layer 8 (front face) ( )lbsP 325,20= .
Left to right and top to bottom: fiber tension, matrix tension, fiber compression, matrix
compression. ....................................................................................................................174
129. Figure 10.27 All non mode based failure indices, load step 14, layer 8 (front face)
( )lbsP 325,20= . Left to right and top to bottom: Tsai Wu, Tsai Hill, Maximum Stress,
Maximum Strain. .............................................................................................................175
130. Figure 10.28 All plies Tsai Hill failure index, load step 14, layer 8 ( )lbsP 325,20= ..176
LIST OF TABLES
Table Page
xx
1. Table 1.1 Description of FE models ...................................................................................6
2. Table 3.1 List of abbreviations used in Table 3.2.............................................................21
3. Table 3.2 Summary of publications in buckling, postbuckling and progressive failure
(abbreviations described in Table 3.1)...............................................................................22
4. Table 3.2 (continued) Summary of publications in buckling, postbuckling and progressive
failure (abbreviations in Table 3.1)....................................................................................23
5. Table 5.1 Summary of results from Spencer-Walker data reduction of ARAMIS
measured out of plane displacement. .................................................................................63
6. Table 6.1 FE modeling features. Element types, boundary conditions and loads ............69
7. Table 6.2 Comparison of results. Different picture frame modeling options (ANSYS) ..72
8. Table 6.3 Mechanical properties of individual plies (British Units) ................................74
9. Table 7.1 Summary of results. Buckling load calculation, two-term Ritz approx............84
10. Table 8.1 Eigenvalues and buckling loads vs. level of load applied to the model ...........91
11. Table 8.2 Eigenvalues and buckling loads vs. level of load applied to the model ...........95
12. Table 8.4 Eigenvalues and buckling loads vs. level of load applied to the model .........101
13. Table 8.5 First three buckling loads for each laminate...................................................104
14. Table 9.1 Estimation of the perturbation force. First mode. Laminate 0 degree. ...........113
15. Table 9.2 Perturbation force estimation. Second Mode. Laminate 0 degree. .................114
16. Table 9.3 Effect of initial imperfections on overall results (laminate 0 deg) .................115
17. Table 9.4 Initial imperfections: estimated vs. adopted for FE correlation......................117
LIST OF TABLES (continued)
Table Page
xxi
18. Table 9.5 Loading schedules in the ANSYS model .......................................................121
19. Table 9.6 Buckling load. Comparison of results.............................................................122
20. Table 10.2 Hashin’s failure criteria expressions.............................................................141
21. Table 10.3 – Strength material properties used in Hashin’s functions [4].......................143
22. Table 10.4 Equivalent displacement and equivalent stress for each failure mode .........149
23. Table 10.5 Energy Released constants [31]....................................................................151
24. Table 10.6 Output damage indices [21]..........................................................................155
25. Table 10.7 Loading schedule, nonlinear analysis with PFA...........................................156
26. Table 10.8 Load levels at occurrence of first damage for each failure mode.................170
27. Table 10.9 Laminate 20 deg .Summary of buckling loads .............................................172
28. Table 10.10 Laminate 20 deg . Final design load carrying capability............................172
29. Table 10.11 Failure criteria compared in the NL-FA-Model. ........................................173
1
CHAPTER ONE
1INTRODUCTION
The industrial use of composite materials has continued to increase steadily over the last three
decades with important developments in the aerospace, wind energy, automotive and sports
industries. Outstanding mechanical properties (strength and stiffness) combined with low weight
make them the material of choice for multiple applications. In the context of the aerospace and
wind industries, it has been common since the 1970’s to use composite materials for primary
structural members; e.g., components in which structural failure leads to catastrophic loss. The
shear webs of main structural components, such as spars and ribs in aircraft wings or wind
blades, are made of composite laminates in a large number of cases.
Traditional metal structures in the aerospace industry have historically been optimized for
minimum weight and validated by well-established analysis methods that are based on a vast
amount of research and testing. In the case of shear resistant webs, conventional aluminum
designs are commonly optimized by the application of the Incomplete Diagonal Tension Theory
(IDTT) first described by Wagner [1] in 1929 and further extended by Kuhn [2] in the 1950’s. As
shown in Figure 1.1, when an isotropic rectangular plate is subjected to pure shear stresses along
the edges, tension and compression stresses exist in the plate. These stresses are equal in
magnitude to the shear stress, and inclined at an angle of 45 degrees. The compressive stresses
on the plate are still resisted immediately after buckling (Figure 1.1 (a)) and well into deep
postbuckling (Figure 1.1 (b)). Wagner’s theory for thin plates under shear proposed an assumed
fully developed postbuckling fold pattern with the thin web modeled as a series of evenly
distributed ribbons or cables carrying tension load only. The method also includes vertical and
2
horizontal stiffeners to which the ribbons are connected. These stiffening members are sized to
remain unbuckled through the entire buckling range of the plate such that the boundary
conditions remain unchanged. This approach is referred to as the theory of “pure diagonal
tension” (PDT).
Figure 1.1 Rectangular isotropic plate subjected to pure shear stresses [2]
Kuhn extended Wagner’s PDT theory to “incomplete diagonal tension” (IDT) [2], which
proposes to limit the buckling of the plate such that the diagonal tension field is not fully
developed as shown in Figure 1.1 (b). Both theories consider the web as inclined tension
members in a frame, but IDT also accounts for the compressive stresses in the plate and its
reinforcing contribution to the stiffeners. Therefore, IDT utilizes the stable postbuckling
behavior of plates in shear to achieve additional load carrying capability and potential weight
3
reductions. Figure 1.2 shows Kuhn’s experimental beam developing a field of diagonal tension
[2]. As mentioned above, the stiffeners dominate the boundary condition of the web so that all of
the buckling is local to the sheet. This progression of the buckling also guarantees that the field
of stresses developed in sheet and stiffener in the post-buckling regime are below the yield stress
of the material and the crippling stress of the stiffeners. And perhaps even more important, this
type of design results in stable postbuckling behavior.
Figure 1.2 Kuhn’s diagonal-tension beam
Composite laminates can be tailored in stiffness or strength, by varying the fiber
directions, which permits a high level of optimization. For a laminated composite design similar
to Kuhn’s diagonal-tension beam design, the function of the vertical stiffeners in the metal
4
design is assumed by the plies with fibers in the vertical direction; whereas, the shear and
diagonal tension field are reacted by plies with fibers at 45-degree angles [3, 4]. Based on this
approach, a commonly adopted conservative design solution is to prescribe a composite lay-up,
which is shear resistant in strength and also exhibits a buckling load well above the expected
range of loading during service. This approach does not take advantage of postbuckling load
carrying capability.
Methods of design and analysis for composite shear webs and hybrid metal-composite
laminates such as Glare [5] have been developed for the past two decades. The basic idea of
design methodologies that utilize the postbuckling strength of composite shear webs is to allow
the panel to carry stresses that are well beyond the buckling load while limiting the allowable
stresses such that no material damage occurs. This is a conservative approach because the final
failure of a composite structure can occur at a load greater than that associated with the first-ply
failure; i.e., first occurrence of damage. In the particular case of the Boeing 787 aircraft, the aft
fuselage skin panels are allowed to buckle under torsion conditions that react the critical loading
on the vertical fin. These panels are designed to prevent (1) Inter-Fiber Failure (IFF) until
loading considerably higher than the Design Limit Load (DLL) and (2) Fiber Failure (FF) until
the final structural collapse (well above 150% of DLL).
The application of this postbuckling design philosophy to laminated composite structures
is the general objective of this research. This dissertation presents an analysis methodology to
validate the design of laminated composite shear webs. It is similar to the IDTT approach
because behavior beyond the initial linear range, including postbuckling, is accounted for in the
analysis. Furthermore, the present work accounts for strength, buckling occurrence and the
progression and onset of damage and its evolution. In order to examine the effects of material
5
damage, four models were developed with increasing levels of complexity ranging from a linear
model with no damage to a fully nonlinear model with progressive failure analysis. The
methodology is validated by correlation with experimental data from a set of four composite
laminated shear panels.
This dissertation presents results from four different finite element (FE) models. The first
model was used to obtain a linearized buckling solution, which provides the buckling critical
loads and corresponding buckling modes as the solution of an eigenvalue problem. A nonlinear
solution was used for the second model, which included finite von Kármán strains and large out-
of-plane displacements. This model was utilized to characterize the response throughout the
complete postbuckling regime. No material nonlinearity or progressive failure analysis was
included in this model. This model (as well as the third and fourth models) used a linear
combination of the buckling modes obtained from the first model to simulate the shape of an
initial imperfection.
The third model differs from the second model because mode-based failure criteria were
included. These criteria were evaluated as a function of load level to determine the critical failure
load and mode for each ply of the laminate. The fourth model used the results from the failure
criteria to model the material damage based on continuum damage mechanics. This resulted in a
progressive failure analysis (PFA) that accounts for material failure and damage progression as a
function of the loading. Table 1.1 describes the four different models used in this dissertation and
their capabilities.
6
Model Abbreviated Name Analysis Capability LE NL NL-FA NL-PFA
Linear eigenvalues X X X X Nonlinear large strains and large displacements
X X X
Failure occurrence X X Failure occurrence and progressive damage
X
Software Used ANSYS ANSYS & ABAQUS ABAQUS ABAQUS
Table 1.1 Description of FE models
7
CHAPTER TWO
2OVERVIEW OF BUCKLING, POSTBUCKLING AND PROGRESSIVE FAILURE
2.1 General requirements and key features of the analysis and simulation
Considering the framework outlined in Chapter 1, the following paragraphs describe the
key features and general requirements for the analytical methods implemented in this
dissertation. The analyses had to predict buckling loads, fully characterize the postbuckling
response (including nonlinear displacements and rotations), predict the onset of material failure,
and describe the postbuckling response conditioned by the post-failure damage propagation.
The commonly used classical laminate theory (CLT) based on the Kirchhoff plate theory
neglects transverse shear stresses. However, composite shear webs can develop significant
transverse shear deformations associated with the out-of-plane deflections in the postbuckling
regime. A method that accounts for first order shear deformation (Reissner-Mindlin plate theory)
was utilized to determine the local ply state of through-the-thickness shear stress.
Appropriate failure criteria were needed to detect the initiation of damage under the
action of postbuckling deflections and stresses. The so-called mode-based failure criteria are
capable of separating different failure modes (fiber tension or compression, matrix tension or
compression, etc.) and were used to detect the onset of failure and as activation functions that
trigger the algorithms that simulate the damage progression [6].
In order to follow the mechanisms that result in the total failure of the structure, material
degradation models were implemented. These models simulated damage propagation and the
updated degradation state of the local material properties. Material degradation models for
composites are, in general, nonlinear material models. Therefore, the post-failure nonlinear
8
material model was a significant feature of the analysis methodology.
Considering the previous point, a procedure to re-establish equilibrium after modifying
the lamina properties was required. This type of operation is sometimes described in the FE
literature as a distinct type of nonlinearity since it involves a change of state in some elements.
Another example of nonlinearity due solely to a change in state is contact elements, which
change to the active state after the prescribed gap is closed. Similarly, layered elements undergo
a discrete change in state when their properties are reduced to reflect the effects of damage.
Although nonlinear finite element analysis is a developed area of simulation, the
progressive failure analysis of nonlinear structures is still an active field of research since failure
theories and damage progression modeling are part of an iterative nonlinear process, with one
being dependent on the other. Comparisons from the World Wide Failure Exercise (WWFE)
[Hinton and Soden, 1998] demonstrated the often poor agreement of existing failure theories
with experimental results. This exercise revealed that even when analyzing simple laminates,
which have been characterized extensively over the past forty years, the predictions using most
theories differ significantly from the experimental observations [7].
The failure theory that more closely approximated the experimental results was Puck’s
Action Plane Strength theory. Matrix failure is analyzed under the hypothesis of brittle fracture,
which is arguably more appropriate for polymeric matrix materials. The method not only
calculates the stresses causing inter fiber failure more realistically than conventional failure
criteria but also predicts the angle in which fracture takes place. Further developments have also
introduced the capability to predict the angle under which fiber band kinking occurs for the fiber
compressive failure. The models developed in this dissertation did utilize a mode based failure
9
criteria that is similar to Puck’s. Cracking and kinking were treated indirectly by degrading the
material properties.
2.2 Preliminary observations about nonlinearity, buckling and post-buckling
The key objectives of the nonlinear analyses of this dissertation were to (1) estimate the
maximum load that the structure could support prior to the onset of material failure and (2)
determine the ultimate load of the structure including the effects of material failure and
degradation.
The first of the above-mentioned objectives essentially consists of determining the pre-
and post-buckling response of the structure. Either with or without material nonlinearities,
structures that undergo buckling will generally follow load-deflection paths similar to the ones
depicted in Figure 2.1.
h
P
Δ
L
P
Δ Δ
P
Δ
Ph /L= 0 h /L= sm a ll h /L= la rge
Postbu ck lin gR eg im e
S nap -th rough
A A '
Figure 2.1 Response of a thin plate or shell under out-of-plane loading
10
The first case, a thin plate with 0=Lh , does not have a collapse point. Because of the
membrane action, the plate increases its stiffness as the displacement grows. For an arch
( largeLh = ) collapse will occur as the load P increases. The most extreme case is commonly
referred to as “snap-through” behavior. This occurs when the structure is evolving from point A
to point A’. The region between A and A’ is dominated by instability since small increments in
displacement beyond point A can generate large fluctuations in the load carrying capability P. If
points A and A’ are in close proximity, the snap-through instability region is small. The buckling
load corresponding to point A may not be as important as what happens between points A and
A’, since the large displacements produced by snap-through can produce structural failure.
For either type of behavior, snap-through or not, the nonlinear response of the structure is
calculated by an incremental analysis, which must include the possibility of decreasing the load
carrying capability as shown in the most right graph of Figure 2.1. The problem statement can be
generically formulated as follows [8]. Let Rt0 be the vector that defines the load distribution
corresponding to the first load step at time 0tt = . At any instant of time τ the load vector is
considered to be proportional to the initial load vector. Therefore,
RR t0βττ = (2.1)
where βτ is the load multiplier for any instant of time τ . For the type of structure and loading
considered in this dissertation, the response as τ increases is of interest. This task requires the
load multiplier βτ to increase or decrease with τ as the structural response is calculated.
The general methodology proposed herein is based on first performing a linearized
buckling analysis to obtain a reasonably good first estimate of the actual buckling load. The
11
linear buckling modes are then used to define the initial imperfection of the structure as a field of
displacements. If imperfections resembling the lowest buckling modes are imposed on the
“perfect” geometry of the model, the load-carrying capacity is much more representative of the
load-carrying capacity of the actual physical structure [8]. The subsequent nonlinear analyses
utilize the initial imperfection as a starting point for the nonlinear postbuckling analysis.
2.3 Linearized buckling solution
The FE commercial packages used in this research utilize a linear buckling solver that
calculates the buckling load factors and the corresponding mode shapes for a structure under the
given load conditions [9]. As shown in Figure 2.2, the solution is based on the assumption that
there exists a buckling point where the primary and the secondary load paths intersect. Before the
point is reached all element stresses change proportionally with the load factor. The lower line in
Figure 2.2 is the nonlinear response. The states labeled as bifurcation points are those in which
the buckling of the structure occurs. As shown, the buckling event for the nonlinear path takes
place at a lower load than that for the linearized path.
Linear Buckling
UnstableRegion
P
Δ
Bifurcation Point
Nonlinear Solution
Secondary Path
BucklingPoint
Figure 2.2 Schematic nonlinear versus linearized responses
12
Analysis for buckling essentially involves determining the distribution of stresses prior to
buckling and the influence of the stresses on the out-of-plane displacement. The geometric
stiffness matrix of the structure reflects the effect of geometric (or displacement) changes on the
element force vector for a known stress state. This matrix and the linear stiffness matrix can be
utilized as a basis for linear buckling analysis, which reduces to an eigenvalue problem. The
eigenvalue closest to zero is the critical load multiplier, and the associated eigenvector gives the
corresponding buckling mode. Negative eigenvalues often are found in the solution, and they
represent potential buckled configurations that the structure could adopt if the applied load is
reversed in direction.
The linear buckling analysis assumes the existence of a bifurcation point where the
primary and the secondary loading paths intersect; see the upper portion of Figure 2.2. At a
bifurcation point, more than one equilibrium position is possible. Since the secondary path is
normally a succession of states of lower elastic energy, the primary path is not usually followed
after the load exceeds this point and the structure is in the postbuckling regime. The slope of the
secondary path at the bifurcation point determines the nature of postbuckling. Positive slope
indicates that the structure will continue to carry load after initial buckling. Negative slope
indicates that the structure will snap through or collapse. Real structures often have geometric
imperfections and loading eccentricities causing the primary path curve and the bifurcation point
to disappear as shown in the nonlinear path of Figure 2.2.
2.4 Nonlinear solution
The curves shown in Figure 2.2 demonstrate linearized buckling, on the linear curve, as
well as nonlinear buckling, which essentially represents a point on the nonlinear load-
13
displacement curve at which the structure becomes unstable. Analysis methods that determine
this type of nonlinear behavior are typically referred to as incremental iterative methods. These
methods start from a known equilibrium point and then determine the increment in
displacements corresponding to an increment in the applied loading.
Some of the methods, such as the popular Newton-Raphson method, can fail to converge
at a zero slope point on the load-displacement curve. This situation is illustrated in Figure 2.3.
To avoid this problem when it occurs, the Arc-Length method, also shown in Figure 2.3, can be
utilized. All results presented herein are based on utilizing the Newton-Raphson method, which
is reviewed in detail in Chapter 9. None of the difficulties illustrated in Figure 2.3 were
encountered for any of the analyses conducted herein.
P
Δ
Newton-Raphson fails here
Δ
PConverged Solution
Spherical arc substep n
1
ii+1
λi
Δλ
Δun
Figure 2.3 Newton-Raphson limitation (left) and Arc-Length methodology (right)
14
2.5 Mode-based failure criteria and progressive failure analysis
The nonlinear postbuckling analysis characterizes the structural load-displacement
response in the absence of failure. That is, the material is assumed to continue carrying load. The
first step in understanding and modeling material failure is to identify failure modes within each
layer of material and their location on the structure.
As described in the literature survey of Chapter 3, the progressive failure analysis of
composite structures usually consists of an approach that as a first step utilizes either the Chang-
Chang or Tsai-Wu failure criteria. Once layer failure is detected, the relevant elastic properties of
the affected element are reduced to zero over a fixed number of steps. This approach is more
sophisticated than the commonly known “ply discount method” for classical laminate strength
analyses and it is a similar method at the element level. Such approaches provide insight on how
the strength degradation evolves, but are unrealistic since post-failure behavior is completely
disregarded [10].
Recent composite damage theories, that model damage evolution more realistically, rely
on continuum constitutive models which feature internal variables that account for the
distribution of microscopic defects that characterizes damage [11]. These are called continuum
damage mechanics (CDM) models, and correspond to the kind of approach used herein. The
CDM model used in this dissertation is supported by the latest version of ABAQUS, as explained
in detail in Chapter 10, and is based on a strain softening material law sized by the volumetric
energy associated with a failure mode. Hashin’s [6] expressions were utilized as failure detection
criteria and activation functions to trigger the constitutive model that simulates damage evolution
at material points.
15
As explained in Chapter 10, Hashin’s criteria were compared with classic single-equation
criteria and were found to be more conservative and more descriptive of the nature of the
damage.
16
CHAPTER THREE
3LITERATURE REVIEW
This chapter presents a review of the most relevant recent works found in a general
literature search involving buckling, postbuckling, and progressive failure analysis. The main
contributions were the formulation of progressive failure models using internal state variables as
proposed by Chang and Chang [12] in 1986, Talreja [13] in 1987, and Chang and Lessard [14] in
1991. Most of the works included in this section use the field variables model for their
progressive damage implementation with different approaches. Table 3.2 shows a summary of
the references found in the field, including type of structure analyzed, loading condition, type of
static solution, whether experimental correlation was presented or not, failure criterion used,
material degradation model used (if any) and the finite element (FE) code used. These fields
reveal trends in the analysis capabilities and the impact that new failure theories have on the
implementation of the damage accumulation algorithms.
The use of commercial FE packages did not become predominant until the turn of the
century, with ABAQUS being the preferred choice for this family of studies. “Ad hoc”
developed codes including specialized NASA applications, such as COMET, have decayed in
usage, since commercial FE software companies have incorporated non-linear analysis
capabilities and assumed the maintenance efforts normally associated with advanced codes. This
change in software usage is coincidental with numerous works that focused on postbuckling
under in-plane shear. It can also be noted that only after 1997 did non-linear analysis become a
common feature, which reflects the maturity in the FE implementation of large displacement
analysis.
17
The types of structure under study are mostly basic assemblies used in aerospace
construction, such as curved and flat panels, with and without holes, and un-stiffened or stiffened
with integral J or blade stiffeners. Papers emphasizing the analysis of more complex buildups
(such as an avionics box or substructures) belong to works focused in practical implementations
of particular projects and were not included in this selection of papers since they do not
constitute a general contribution to the field.
Regarding the failure theory used, the publications can be divided into two general
categories: classic failure theories (maximum stress, maximum strain, Tsai-Hill, Tsai-Wu,
Hoffman, and their modifications), and mode-based failure theories (Hashin, Hashin-Rotem,
Christensen, Chang-Lessard, Puck, and LaRC family). After the results of the World Wide
Exercise in Failure (WWFE) were published in 1998 [7], emphasis was put in developing new
physically based phenomenological failure criteria that incorporated new features such as Puck’s
concept of angle of fracture (applicable to matrix compression), fiber kinking band angle
(applicable to fiber compression) and advances from the field of fracture mechanics (applicable
to matrix tension). The methods of the family labeled as LaRC (Langley Research Center) are
phenomenological failure criteria. The LaRC models were first implemented in progressive
failure analysis by Ambur et al. [11] in 2004. As shown in Table 3.2, mode-based failure criteria
have become the dominant choice.
All of the recent material degradation models, as shown in Table 3.2, rely on a collection
of internal variables to characterize the accumulation of damage after failure has been detected
by the failure criteria. The two general types of models include (1) the Chang & Lessard [14]
model that reduces abruptly to zero (or to a value close to zero to avoid numerical instability) the
different material stiffness properties associated with each failure mode (in Tables 3.1 and 3.2,
18
these models are referred under the abbreviations IRSP and GRSP), and (2) the other group of
models that rely on continuum damage mechanics (CDM) to reduce the stiffness material
properties following constitutive laws that consider the density distribution of cracks over a
volume (these models are referred in Tables 3.1 and 3.2 under the abbreviation CDM with a
suffix that depends on the assumptions made for each implementation). It can be noted that CDM
models became predominant after 2005 when Camanho and Davila very successfully used them
to model the damage progression of delamination damage and the separation of stiffener flanges.
Following Camanho and Davila, the post-failure material degradation model follows a
constitutive law with strain softening that is correlated with the experimental values of the
critical values of energy release rates associated with the three fracture modes IG , IIG , IIIG .
Singh and Kumar [15] presented in 1998 their study of thin laminates for different lay-
ups with a NASTRAN FE model for comparison and failure analysis using the Tsai-Hill
criterion. Huang and Minnetyan [16] published in 1999 a study of J-stiffened panels in the
postbuckling range with an in-house developed FE solver and failure based on maximum stress
and modified Tsai-Hill criterion. In 1999, Sleight performed a general evaluation of the state of
the art progressive failure methodology for several types of structures including the rail-shear
panel, with non-linear analysis, using the maximum strain, Hashin, and Chirstensen criteria. For
compression loading, Davila et al. [17] carried out in 1999 one of the first implementations using
ABAQUS for the non-linear analysis. The study was conducted for notched composite panels
with blade stiffeners and cross stitching with Kevlar fiber, replicating a typical wing box cover
panel. The effect of the Kevlar stitches in the propagation of damage was investigated. The
failure analysis was again mode-based with Hashin’s criterion.
19
The NASA-ICASE group, formed by Jaunky, Ambur, Davila and Hilburger [18],
presented in 2001 their study of panels with and without holes and bead-stiffened panels under
compression and shear well into the postbuckling range. All of the results were obtained using
ABAQUS with failure detected through Hashin’s theory. In 2002 Ambur et al. [19] extended
their work to stiffened panels under shear well into the postbuckling range with ABAQUS and
Hashin’s criterion. They also included the same type of panels but damaged with a notch in an
angle. Zemcik and Las included Puck’s formulation in their analysis in 2005 [20].
The findings of the WWEF had an impact in PFA works as reflected by the NASA-
ICASE group. In 2004 Ambur et al. [18] implemented PFA using ABAQUS and the LaRC02 set
of criteria for panels in compression. Comparisons were made with the same PFA based on
Hashin’s failure criterion and also on Chang-Lesard’s degradation model. In 2005 Zemcik and
Las [20] implemented Puck’s criterion in a PFA, although that work does not fall strictly into the
scope of this dissertation because it used a shock loading.
Since 2005, PFA works predominantly include mode-based phenomenological failure
criteria such as Hashin or the LaRC family. It has also become predominant to use material
degradation models based on continuum damage mechanics. These methods utilize strain
softening laws previously correlated with energy release rates obtained through testing for each
failure mode.
No previous works have covered the study of postbuckled in-plane shear loaded panels
with mode-based failure and material degradation in the progressive failure analysis. Combining
these two advanced features (mode based failure and material degradation) with a nonlinear
postbuckling model is the key contribution of this dissertation. This research also explores the
20
benefits of separating failure for the different modes taking place during the postbuckling of in-
plane shear loaded panels. Such information is expected to prove valuable to the designer in
understanding the damage evolution and its interaction with the instability behavior when the
structure is loaded well into the postbuckling regime.
The current literature review found a low number of recent works using the ANSYS
software package versus the ABAQUS package. The practical exploration of the ANSYS
capabilities to support a PFA implementation and the decision to choose ABAQUS to take the
dissertation work to a successful completion can also be considered an added benefit of this
research.
21
Abbreviation Description
EC Experimental correlation
LG Linear geometry (analysis)
NLG Nonlinear geometry (analysis)
NLM Nonlinear material (analysis)
PB Post buckling (analysis)
IRSP Instantaneous reduction of stiffness properties (upon failure onset)
GRSP Gradual reduction of stiffness properties, following a fixed law over a
number of time steps (upon failure onset)
CDM-UCD Continuum damage mechanics model assuming uniform cracks density
CDM-SCD Continuum damage mechanics model assuming statistical cracks density
distribution
CDM- iCG Continuum damage mechanics with constitutive model correlated with the
energy release rates of fracture modes I, II, and III
AVD Artificial viscous damping
DELAM Delamination
ST Shapery theory
Table 3.1 List of abbreviations used in Table 3.2
Table 3.2 Summary of publications in buckling, postbuckling and progressive failure (abbreviations described in Table 3.1)
Year Researchers Analysis Type Structure Type Loading Condition
EC Failure Criterion Material Degradation
FEM Code
1991 Chang & Lesard LG-NLM Plate with a cutout Compression yes Chang (Hashin modified)
IRSP PDHOLE
1992 Minnetyan et al. LG-NLM Plate with a cutout Tension no Not available CODSTRAN Engelstad, Reddy
& Knight NLG-PB Plate with and w/o cutout Compression yes Max stress & Tsai Wu Not available Own code
1995 Shahid & Chang LG Plate Tens, shear yes Hashin modified CDM-UCD PDCOMP
Coats & Harris LG Plate with cutout Tension yes CDM- iCG COMET-FL
1997 Sleight & Knight NLG-PB Stiffened & unstiffened panel with & w/o cutout
Compression yes Max strain, Hashin, Christensen
IRSP & GRSP
COMET
22 Moas & Griffin NLG-PB Curved frame Transverse yes Tsai-Wu, Max strain IRSP Own code
Singh et al NLG-PB Plate Compression no CDM-SCD 1998 Singh et Kumar NLG-PB Plate Shear no Tsai-Hill & Max stress IRSP NASTRAN Gummadi et al NLG-PB Curved panel Transverse no Not available 1999 Huang and
Minnetyan NLG-PB J stiffened panel,stitched Shear yes Modified Tsai-Hill &
Max stress IRSP Own code
Davila Ambur, and McGowan
NLG-PB Stiffened notched panel, stitched
Compression yes Hashin IRSP ABAQUS
Sleight NLG-PB Rail-shear panel, panel with & w/o hole, blade-stiffened panel
Tension, shear compression
yes Max strain, Hashin, Christensen
IRSP COMET
Wang, Lotts, Sleight
NLG-NLM Stiffened panel Tension yes Max Stress, Hashin, Hashin-Rotem
IRSP COMET-AR
Baranski et al NLG-PB Plate Compression no Hashin Not available
Table 3.2 (continued) Summary of publications in buckling, postbuckling and progressive failure (abbreviations in Table 3.1)
Year Researchers Analysis Type
Structure Type Loading Condition
EC Failure Criterion Material Degradation
FEM Code
2000 Knight et al NLG-PB Plate Compression yes Max strain IRSP STAGS 2001 Jaunky, Ambur,
Davila, & Hilburger NLG-PB Panel with&w/o cutouts
Bead-stiffened panel Compression & shear
yes Hashin IRSP ABAQUS
McGowan,Davila Ambur NLG-NLM Notched panel Compression yes Chang (Hashin modif) IRSP ABAQUS Knight, Rankin, Brogan NLG-NLM Plate with a hole Tension no Max strain CDM + AVD STAGS 2002 Ambur, Jaunky Hilburger NLG-PB Stiffened panel Shear yes Hashin IRSP ABAQUS Goyal, Jaunky, Ambur
Johnson NLG-NLM Flat and curved panels Shear &
Compression yes Chang (Hashin
modified) CDM for DELAM, IRSP
ABAQUS
2003 Minnetyan, Zhao, Chamis NLG-NLM Adaptive plate airfoil Tension pressure no Modif Tsai-Hill, Max stress Not available Own code Hyer, Wolford, Knight NLG-NLM Non-circular cylinder Inter pressure no Max stress GRSP STAGS
23 Nagesh NLG-NLM Pressure vessel Inter pressure yes Tsai-Wu GRSP ANSYS
2004 Ambur, Jaunky, Davila NLG-NLM Panel Tens, compr yes LaRC02, Chang-Less. IRSP ABAQUS 2005 Hilburger & Nemeth NLG-NLM Cylind shell reinf hole Compression yes Hashin IRSP STAGS Hermann, Lo
Mamarthupatti NLG-PB Panel Compression no Tsai-Wu, Max Stress Not available ANSYS
Basu, Waas, Ambur NLG-NLM-PB
Panel with hole, double notched panel
Shear, Compression
yes Shapery theory ST ABAQUS
Camanho & Davila NLG-NLM-Delamination
Stiffened rectangular panel
Bending yes Mixed mode quadratic interaction
CDM- iCG ABAQUS
Pinho Iannucci Robinson NLG-NLM Rectangular panel Tens/compress yes LaRC04 CDM- iCG ABAQUS
2006 Miami NLG-NLM- Rectangular panel LaRC02 CDM- iCG ABAQUS
24
CHAPTER FOUR
4SCOPE AND OBJECTIVES
This dissertation presents a progressive failure methodology to support the design of
composite shear webs. Nonlinear finite element (FE) models combined with techniques to
predict the onset of failure and material damage evolution are used to analyze the panels and
expand their working range well into the postbuckling regime. A complete analysis methodology
is laid out with increasing complexity in its approach to the problem. The methodology was
validated by correlation of FE results with experimental data. Regarding other general
considerations that define the scope of this work, this research is concerned with the damage
onset, accumulation, and progression, but it was not concerned with fatigue damage mechanisms.
The type of loading under consideration was static for the analysis and quasi-static for the
testing. The type of structures analyzed herein were flat unstiffened laminates.
The experimental results were recorded using strain gages as well as the latest generation
photo-sensitive digital image system (ARAMIS). The strain and displacement results collected
for the postbuckling response of the panels were compared between ARAMIS and the strain
gages in order to assess consistency and accuracy. Diverse mathematical treatments of the test
data such as the Southwell’s method (in the Spencer-Walker version for buckling of plates) were
applied to extract the experimental values of the critical buckling loads for each specimen.
The analysis methodology is presented with increasing levels of complexity. This
incremental analysis approach was taken (1) in order to independently evaluate each type of
analysis, and (2) to compare results from two commercial FE packages, ANSYS and ABAQUS.
The types of models that were developed are listed as follows: (1) a linear model to estimate the
25
panel buckling load based on eigenvalue analysis, (2) a nonlinear model with von Kármán
nonlinear strains to predict the postbuckled load-displacement and load-strain response, (3) the
nonlinear model from step 2 with mode-based failure indices for each material layer, and (4) the
nonlinear model from step 3 with a continuum damage mechanics materials degradation model
that utilizes the mode-based failure indices as damage activation functions.
The linear models from step 1 and the nonlinear models from step 2 were developed
using ANSYS and ABAQUS. The nonlinear models from steps 3 and 4 were developed using
ABAQUS. The critical loads obtained with the linear models from step 1 were compared with
the experimental buckling loads determined from test results. The nonlinear models from step 2
were used to fully characterize the postbuckling response (without failure) and correlate it with
the response recorded during tests. The high level of correlation obtained validated all aspects of
modeling the structure with finite elements and the results given by the nonlinear solution.
The model utilized for step 3 relied on Hashin’s mode-based failure criteria to provide
failure indices for four different types of failure: fiber tension and compression, and matrix
tension and compression. For one of the laminates (out of the four that were tested) damage
occurrence was assessed for the different failure modes captured in the analysis. In a separate
model, with failure detection only, the Hashin’s mode-based failure criteria were compared to
four classic single equation criteria for composite structures.
For step 4 the progressive failure analysis (PFA) capability was added to the model. The
PFA capability was based on a Continuum Damage Mechanics (CDM) constitutive post-failure
material model. For the same laminate as mentioned above, the results of the complete nonlinear
with PFA analysis were examined to describe the evolution of damage and the damage state
26
corresponding to the final collapse of the structure. The results from the complete analysis were
compared with the nonlinear solution without failure and with the test results.
27
CHAPTER FIVE
5EXPERIMENTAL STUDY
Four different hybrid glass/epoxy-carbon/epoxy panels were tested under in-plane shear
loading as shown in Figure 5.1. Loading, ranging from zero load to the load at panel collapse,
was applied with constant displacement increments of 0.005 mm. Rosette strain gages were
installed at the center point of both sides of the panel following the arrangement shown in Figure
5.1.
Figure 5.1 Schematic diagram of picture frame fixture and panel geometry.
The strain gages collected data through six instrumentation channels. All of the panels
were built using a lay-up sequence consisting of alternating plies of pre impregnated Double
28
Biaxial Glass/Epoxy (denoted as DB) with plies of pre impregnated Unidirectional
Carbon/Epoxy tape (denoted as UC). The basic laminate followed the symmetric sequence:
[ ]DBUCDBUCUCDBUCDB ,,,,,,, or [ ]SUCDBUCDB ,,, . Tests were
performed based on the orientation of the UC carbon layers (0, 20, 45, and 90 degrees) with
respect to the direction of the load; i.e., an angle of 0 degrees corresponds to loading aligned in
the direction of the UC carbon layers.
The apparatus used was a picture frame fixture mounted on an MTS uniaxial load cell, as
shown in Figure 5.2. The frame consists of steel arms of rectangular cross section, with panel
attachments through fasteners, and hinge bolts in all four corners. Based on this setup, the
boundary conditions at the edges of the panel are considered to be fixed-clamped, and the four
arms act as loading edges.
In addition to the strain gage data, a photo-sensitive digital image system (ARAMIS) was
utilized to detect and record the out of plane displacements of the surface of the panels. The
ARAMIS results were compared with the out of plane displacements predicted by FE analyses.
In general terms, the methodology followed for all four specimens was to record the test readings
and attempt to correlate them with the FE results (either ANSYS or ABAQUS).
5.1 Data reduction of strain gage readings
All of the panels exhibited postbuckling strength, and were loaded until final destruction.
The numerical simulations described in subsequent sections will explore different aspects of the
failure analysis to gain further insight. The data recording systems described in this section
collected a vast amount of information during each test run. The following plots present limited
data in an attempt to reveal the onset of buckling for each of the laminates as well as relevant
29
trends and changes in slope. An actual panel in the picture frame fixture is shown in Figure 5.2.
Figure 5.2 Picture frame test setup.
30
0
20
40
60
80
100
120
140
160
180
0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000
Microstrains (mm/mm x 1E-3)
Load Cell Force (kN)
Front FaceBack Face
Figure 5.3 Laminate 20 deg. Strains measured on the tension diagonal.
0
20
40
60
80
100
120
140
160
-9000 -8000 -7000 -6000 -5000 -4000 -3000 -2000 -1000 0 1000 2000 3000
Microstrains (mm/mm x 1E-3)
Load Cell Force (KN)
Back Face Front Face
Figure 5.4 Laminate 20 deg. Strains measured on the compression diagonal.
31
0
20
40
60
80
100
120
140
0 500 1000 1500 2000 2500 3000
Microstrains (mm/mm x 1E-6)
Load
Cell
For
ce (k
N) Back Face
Front Face
Figure 5.5 Laminate 45 deg. Strains measured on the tension diagonal.
0
20
40
60
80
100
120
140
-12000 -10000 -8000 -6000 -4000 -2000 0 2000 4000 6000 8000
Microstrains (mm/mm x 1E-6)
Load
Cell
For
ce (k
N)
Back FaceFront Face
Figure 5.6 Laminate 45 deg. Strains measured on the compression diagonal.
32
0
20
40
60
80
100
120
0 1000 2000 3000 4000 5000 6000 7000 8000 9000
microstrains (mm/mm x 1E-6)
Loa
d C
ell F
orce
(kN
)
Back FaceFront Face
Figure 5.7 Laminate 90 deg. Strains measured on the tension diagonal.
0
20
40
60
80
100
120
-8000 -6000 -4000 -2000 0 2000 4000 6000
microstrains (mm/mm x 1E-6)
Loa
d C
ell F
orce
(kN
)
Back FaceFront Face
Figure 5.8 Laminate 90 deg. Strains measured on the compression diagonal.
33
0
20
40
60
80
100
120
140
160
0 1000 2000 3000 4000 5000 6000 7000 8000 9000 10000 11000
microstrains (mm/mm x 1E-6)
Loa
d C
ell F
orce
(kN
)
Front FaceBack Face
Figure 5.9 Laminate 0 deg. Strains measured on the tension diagonal.
0
20
40
60
80
100
120
140
160
-18000 -15000 -12000 -9000 -6000 -3000 0 3000 6000
microstrains (mm/mm x 1E-6)
Loa
d C
ell F
orce
(kN
)
Front FaceBack Face
Figure 5.10 Laminate 0 deg. Strains measured on the compression diagonal.
34
Strain on tension direction, front face
0
20
40
60
80
100
120
140
160
0 1000 2000 3000 4000 5000 6000 7000 8000 9000
microstrains (mm/mm 1E-6)
For
ce a
t lo
ad c
ell (
kN)
Laminate 90 degLaminate 0 degLaminate 20 degLaminate 45 deg
Figure 5.11 Comparison of all laminates. Strains on tension diagonal, front face
Strain on compressed diagonal, front face
0
20
40
60
80
100
120
140
160
-3000 -2000 -1000 0 1000 2000 3000 4000 5000
microstrains (mm/mm 1E-6)
For
ce a
t lo
ad c
ell (
kN)
Laminate 90 degLaminate 0 degLaminate 20 degLaminate 45 deg
Figure 5.12 Comparison of all laminates. Strains on compression diagonal, front face
35
5.2 Data reduction of the ARAMIS optical system measurements
The ARAMIS optical system consists of a group of two cameras capturing digital images
of the specimen during the test. It tracks a network of markers attached to the surface of the
specimen, characterizing surface displacements and strains well into the nonlinear range.
The markers are distributed over the specimen and separated from each other by a pitch
several orders of magnitude finer than the characteristic length of the buckling modes exhibited
by the structure. The database recorded by ARAMIS for each specimen was interrogated in
several ways, and the interpretation of the results is presented in this section. Figure 5.13 shows
the axes to which ARAMIS relates strain measurements.
R2.5
12 in
17 in
ARAMIS Reference Axes
45 deg
Loading Direction
Test Panel
Pin JointFrame Member
Rosette Strain Gage
Pin Joint
Pin Joint
Pin Joint
Figure 5.13 ARAMIS reference axes for strain measurement
36
5.2.1 Laminate G - 20 degree data reduction
The ARAMIS database of recordings allows for fringe plotting of displacements and
strains of the surface under observation, as shown in Figures 5.14 through 5.17.
Figure 5.14 Laminate 20 deg, front face, out of plane displacement ( )lbsP 1.39746= .
Figure 5.15 Laminate 20 deg, front face, xxε strain, ( )lbsP 1.39746= .
37
Figure 5.16 Laminate 20 deg, front face, yyε strain, ( )lbsP 1.39746= .
Figure 5.17 Laminate 20 deg, front face, xyε strain, ( )lbsP 1.39746= .
For the correlation of the test results with the FE models, the ARAMIS database was
queried for xxε and yyε strain values on the front face on both diagonals under tension and under
compression. Figures 5.18 and 5.20 show the strains along the whole length of the diagonals for
different load levels. Figures 5.19 and 5.21 show load vs. strain only on points of the diagonals
separated an inch or less from the center of the panel.
38
Laminate 20 deg, Exx strain over compressed diagonal for different load levels
-2.00
-1.50
-1.00
-0.50
0.00
0.50
1.00
0 25 50 75 100 125 150 175 200 225 250 275 300
X position (mm)
Exx
stra
in (%
)
203547617793109124138153167142
Figure 5.18 xxε strains, compression diag., front face, different load levels.
0
20
40
60
80
100
120
140
-1.5 -1 -0.5 0 0.5 1
Exx strain (%)
Act
uato
r loa
d (k
N)
124.65 135.01
141.27 145.45
130.86 149.65
155.97 162.32
166.58 172.97
175.11
Figure 5.19 xxε vs load, front face compression diag., around center of panel.
Curves for locations measured from the corner of the panel (center at 150.00 mm).
39
Figure 5.19 shows strains on points close to the center of the panel and located under the
footprint of the strain gage (125.00 mm to 150.00 mm). Simultaneous observation of Figures
5.18 and 5.19 reveals that strains at some of the locations changed from compression to tension
after the occurrence of buckling. This conclusion is consistent with the mode shape shown in
Figure 5.14.
Observation of Figures 5.20 and 5.21 reveals that all of the points on the tension diagonal
undergo increasing levels of tension with little sensitivity to the occurrence of buckling.
Therefore, the tension diagonal basically behaves like a truss bar under axial loading.
Laminate 20 deg, Eyy strains over tension diagonal for different load levels
-0.10
0.00
0.10
0.20
0.30
0.40
0.50
0 50 100 150 200 250 300
Y position (mm)
Eyy
stra
in (%
)
14.8127.0050.1761.4074.0674.0685.5396.76105.36116.83126.14134.98
Figure 5.20 yyε strains on the tension diagonal for different load levels.
40
0
20
40
60
80
100
120
140
0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40
Eyy strain (%)
Act
uato
r loa
d (k
N)
123.563975
139.969694
150.22496
160.476443
174.835777
Figure 5.21 yyε vs load - tension diagonal, locations around center of panel.
Curves for locations measured from the corner of the panel (center at 150.00 mm).
41
5.2.2 Laminate H - 45 degree data reduction
The ARAMIS database of recordings allows for fringe plotting of displacements and
strains of the surface under observation, as shown in Figures 5.22 through 5.25.
Figure 5.22 Laminate 45 deg front face, out of plane displacement ( )lbsP 65.33139=
Figure 5.23 Laminate 45 deg, front face, xxε strain, ( )lbsP 65.33139= .
42
Figure 5.24 Laminate 45 deg, front face, yyε strain, ( )lbsP 65.33139= .
Figure 5.25 Laminate 45 deg, front face, xyε strain, ( )lbsP 65.33139= .
To correlate the test results with the finite element models of the structure, the ARAMIS
database was queried for specific xxε and yyε values on locations on both diagonals under tension
and under compression, as shown in Figures 5.26 and 5.27.
43
Laminate 45 deg, Exx strain over compressed diagonal for different load levels
-2.00
-1.50
-1.00
-0.50
0.00
0.50
1.00
0 25 50 75 100 125 150 175 200 225 250 275 300
X position (mm)
Exx
stra
in (%
)
11.2125.2836.7347.9360.1070.5983.2393.01103.98113.99129.97141.66147.41
Figure 5.26 xxε strains on the compression diagonal for different load levels.
0
20
40
60
80
100
120
140
160
-1.20 -1.00 -0.80 -0.60 -0.40 -0.20 0.00 0.20 0.40 0.60 0.80
Exx strain (%)
Act
uato
r loa
d (k
N)
124.27
134.65
140.91
145.09
130.50
149.29
155.59
161.91
166.13
172.47
176.71
Figure 5.27 xxε vs load. Compression diag., locations around center of panel.
Curves for locations measured from the corner of the panel (center at 150.00 mm).
44
Figure 5.27 shows strains on points close to the center of the panel, and located under the
footprint of the strain gage (125.00 mm to 150.00 mm). Simultaneous observation of Figures
5.26 and 5.27 reveals that some of the strain gage readings changed from compression to tension
after the occurrence of buckling. This conclusion is consistent with the mode shape shown in
Figure 5.22.
Observation of Figures 5.28 and 5.29 reveals that all of the points on the tension diagonal
undergo increasing levels of tension with little sensitivity to the occurrence of buckling.
Laminate 45 deg, Eyy strains over tension diagonal for different load levels
0.00
0.20
0.40
0.60
0.80
1.00
1.20
1.40
0 50 100 150 200 250 300
Y position (mm)
Eyy
stra
in (%
)
14.8127.0050.1761.4074.0674.0685.5396.76105.36116.83126.14143.34147.41
Figure 5.28 yyε strains on the tension diagonal for different load levels.
45
0
20
40
60
80
100
120
140
160
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00
Eyy strain (%)
Act
uato
r loa
d (k
N)
150.24
125.63
174.85
137.94
162.54
Figure 5.29 yyε strains on the tension diagonal for different load levels.
Curves for locations measured from the corner of the panel (center at 150.00 mm).
46
5.2.3 Laminate E - 90 degree data reduction
The ARAMIS database of recordings allows for contour plotting of displacements and
strains of the surface under observation, as shown in Figures 5.30 through 5.37.
Figure 5.30 Laminate 90 deg front face, out of plane displacement ( )lbsP 9.31044= .
Figure 5.31 Laminate 90 deg, front face, xxε strain, ( )lbsP 4.23525= .
47
Figure 5.32 Laminate 90 deg, front face, yyε strains, ( )lbsP 9.31044= .
Figure 5.33 Laminate 90 deg, front face, xyε strains, ( )lbsP 9.31044= .
To correlate the test results with the finite element model of the structure, the ARAMIS
database was queried for specific xxε and yyε strain values on locations on both diagonals, under
tension and under compression.
48
Laminate 90 deg, Exx strain over compressed diagonal for different load levels
-1.20
-1.00
-0.80
-0.60
-0.40
-0.20
0.00
0.20
0.40
0.60
0 25 50 75 100 125 150 175 200 225 250 275 300
X position (mm)
Exx
stra
in (%
)
10263853667992105114124131138
Figure 5.34 xxε on the compression diagonal for different load levels.
0
20
40
60
80
100
120
140
160
-1.2 -1 -0.8 -0.6 -0.4 -0.2 0
Exx strain (%)
Act
uato
r loa
d (k
N)
125.58 135.83
146.08 156.33
166.58 174.79
Figure 5.35 xxε vs. load - compression diag., locations around center of panel.
Curves for locations measured from the corner of the panel (center at 150.00 mm).
49
Figure 5.35 shows strains on points close to the center of the panel and located under the
footprint of the strain gage (125.00 mm to 150.00 mm). Figures 5.34 and 5.35 were extracted
from the same dataset that generated the mode shape shown in Figure 5.30.
Observation of Figures 5.36 and 5.37 reveals that all of the points on the tension diagonal
undergo increasing levels of tension with little sensitivity to the occurrence of buckling.
Laminate 90 deg, Eyy strains over tension diagonal for different load levels
-0.10
0.00
0.10
0.20
0.30
0.40
0.50
0 50 100 150 200 250 300
Y position (mm)
Eyy
stra
in (%
)
14.8127.0050.1761.4074.0674.0685.5396.76105.36116.83126.14134.98
Figure 5.36 yyε on the tension diagonal for different load levels.
50
0
20
40
60
80
100
120
140
0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40
Eyy strain (%)
Act
uato
r loa
d (k
N)
123.56
139.97
150.22
160.48
174.84
Figure 5.37 yyε on the tension diagonal for different load levels.
Curves for locations measured from the corner of the panel (center at 150.00 mm).
51
5.2.4 Laminate F - 0 degree data reduction
No fringe plots were obtained for this laminate. However, strains xxε and yyε along the
tension and compression diagonals were obtained for the front surface. The data collected was
reduced as shown in Figures 5.38 through 5.41.
Laminate 0 deg, Exx strain over compressed diagonal for different load levels
-3.50
-3.00
-2.50
-2.00
-1.50
-1.00
-0.50
0.00
0.50
1.00
1.50
0 25 50 75 100 125 150 175 200 225 250 275 300
X position (mm)
Exx
stra
in (%
)
16
31
46
61
79
95
111
125
140
155
169
167
178
189
199
Figure 5.38 xxε on the compression diagonal for different load levels.
52
0
20
40
60
80
100
120
140
160
180
-2.3 -2.2 -2.1 -2 -1.9 -1.8 -1.7 -1.6 -1.5 -1.4 -1.3 -1.2 -1.1 -1 -0.9 -0.8 -0.7 -0.6 -0.5 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4
Exx strain (%)
Act
uato
r loa
d (k
N)
126.92
137.25
147.64
158.10
168.63
Figure 5.39 xxε vs. load - compression diag., locations around center of panel.
Curves for locations measured from the corner of the panel (center at 150.00 mm).
Figure 5.39 shows the strains on points close to the center of the panel, and located under
the footprint of the strain gage (125.00 mm to 150.00 mm). Simultaneous observation of Figures
5.38 and 5.39 reveals that none of the strain gage covered points changed from compression to
tension after the occurrence of buckling. Observation of Figures 5.42 and 5.41 reveals that all of
the points on the tension diagonal undergo increasing levels of tension with little sensitivity to
the occurrence of buckling.
53
Laminate 0 deg, Eyy strains over tension diagonal for different load levels
-0.10
-0.05
0.00
0.05
0.10
0.15
0.20
0.25
0.30
0 50 100 150 200 250 300
Y position (mm)
Eyy
stra
in (%
)
15.5330.5861.1678.8494.6194.61110.85124.95140.24155.29169.38166.52
Figure 5.40 yyε strains on the tension diagonal for different load levels.
0
20
40
60
80
100
120
140
160
180
200
220
-0.05 0.00 0.05 0.10 0.15 0.20 0.25 0.30
Eyy strain (%)
Act
uato
r loa
d (k
N)
125.59
135.85
146.10
154.31
164.56
Figure 5.41 yyε strains on the tension diagonal for different load levels.
Curves for locations measured from the corner of the panel (center at 150.00 mm).
54
5.3 Comparison plot of ARAMIS data vs. strain gage data
The following figures show both the direct readings from the strain gages and the
ARAMIS reduced data. Both sources of measurement are in agreement except for two cases
which are discussed at the end of this section.
0
20
40
60
80
100
120
140
-15000 -10000 -5000 0 5000 10000
Exx strain (microstrains)
Act
uato
r loa
d (k
N)
124.65
135.01
141.27
145.45
130.86
149.65
155.97
162.32
166.58
172.97
175.11
strain gage
0
20
40
60
80
100
120
140
160
0 500 1000 1500 2000 2500 3000 3500 4000
Eyy strain (microstrains)
Act
uato
r loa
d (k
N)
123.56
139.97
150.22
160.48
174.84
strain gage
Figure 5.42 Lam 20 degree - strains measured at different locations of the tension and the
compression diagonal vs. actuator load. ARAMIS vs. strain gage.
55
-10
10
30
50
70
90
110
130
150
-15000 -10000 -5000 0 5000 10000
Exx strain (microstains) on compression diagonal
Act
uato
r loa
d (k
N)
124.27
134.65
140.91
145.09
130.50
149.29
155.59
161.91
166.13
172.47
176.71
strain gage
-20
0
20
40
60
80
100
120
140
160
0 2000 4000 6000 8000 10000 12000
Eyy strain (microstrains) on tension diagonal
Act
uato
r loa
d (k
N)
150.24
125.63
174.85
137.94
162.54
strain gage
Figure 5.43 Laminate 45 degree - strains measured at different locations of the tension and the
compression diagonal vs. actuator load. ARAMIS vs. strain gage.
56
0
20
40
60
80
100
120
-8000 -7000 -6000 -5000 -4000 -3000 -2000 -1000 0
Exx strain (microstrains) on the compressed diagonal
Act
uato
r loa
d (k
N) 125.58
135.83
146.08
156.33
166.58
174.79
strain gage
0
20
40
60
80
100
120
140
160
0 500 1000 1500 2000 2500 3000 3500 4000
Eyy strain (microstrains) on tension diagonal
Act
uato
r loa
d (k
N) 123.56
139.97
150.22
160.48
174.84
strain gage
Figure 5.44 Laminate 90 degree - strains measured at different locations of the tension and the
compression diagonal vs. actuator load. ARAMIS vs. strain gage.
57
0
20
40
60
80
100
120
140
160
180
-18000 -16000 -14000 -12000 -10000 -8000 -6000 -4000 -2000 0
Exx strain (microstrains) on the compressed diagonal
Act
uato
r loa
d (k
N) 126.92
137.25
147.64
158.10
168.63
strain gage
0
20
40
60
80
100
120
140
160
180
200
220
0 500 1000 1500 2000 2500 3000
Eyy strain (microstrains) on the tension diagonal (lam 0deg)
Act
uato
r loa
d (k
N)
125.59
135.85
146.10
154.31
164.56
strain gage
Figure 5.45 Laminate 0 degree - strains measured at different locations of the tension and the
compression diagonal vs. actuator load. ARAMIS vs. strain gage.
The strain gage and ARAMIS data were found to be in reasonably good agreement and
provided an additional check and validation of the strain gage data. The plots corresponding to
58
tension for both the 0 and the 90 degree laminates did not show a clear correlation; however, the
rest of the plots provide the consistency to validate the test data from both the strain gages and
ARAMIS system.
5.4 Experimental determination of buckling loads. Spencer-Walker method
Southwell proposed in 1934 a method to determine the buckling load of struts under
compression from experimental readings of the out of plane displacements measured at the
middle point of the strut [24]. The Southwell method was extended to the buckling of plates;
however, it exhibits important limitations in situations of high nonlinearity [25] such as the
plates considered in this dissertation. Spencer and Walker published in 1975 a method that
constitutes an extension of the Southwell method for rectangular plates with a variety of
boundary conditions and loading.
5.4.1 Southwell plots for struts under compression
Southwell considered a simply supported strut of length L and constant flexural
rigidity EI , with an existing distributed imperfection ( )xw~ along its length and under the action
of a quasi-static compressive load P . The additional transverse deflection is denoted here as
( )xw and it is the magnitude usually measured in practical tests, where x is measured from an
origin at one end of the strut. The values of these functions at 2Lx = are denoted by the
corresponding uppercase sW ' , and the Fourier coefficients by sWi ' . The equilibrium is given by
equation (5.1):
''2''2 ~wwwIV αα −=+ , where EIP=2α (5.1)
with the boundary conditions:
59
( ) ( ) ( ) ( ) 000 '''' ==== LwLwww (5.2)
Assuming that the imperfection shape can be expressed as a Fourier series,
( ) ∑∞
=⎟⎠⎞
⎜⎝⎛=
1sin~~
nn L
xnWxw π (5.3)
which leads to
( ) ∑⎥⎥⎦
⎤
⎢⎢⎣
⎡⎟⎠⎞
⎜⎝⎛⎟
⎠
⎞⎜⎝
⎛−=
−
Lxn
PP
Wxw nn
πsin1~1
(5.4)
where nP is the buckling load corresponding to the thn buckling mode:
222 LEInPn π= (5.5)
1
1~ −
⎟⎠⎞
⎜⎝⎛ −=
PPWW n
nn (5.6)
Southwell noted that “if P is a considerable fraction of 1P ” then
11
11 1~ −
⎟⎠⎞
⎜⎝⎛ −==
PPWWW (5.7)
so that as 1PP → the fundamental mode predominates. Hence, if 1~~ WW = , then
WPWPW ~
1 −⎟⎠⎞
⎜⎝⎛= (5.8)
Southwell’s brilliant suggestion was to plot W vs ( )PW and obtain CPP =1 as the slope
of the predicted straight-line graph. However, equation (5.8) was not derived for any arbitrary
deflection parameter W of an elastic structure under the action of an arbitrary load parameter P
60
[25]. At most, the analysis shows that for boundary value problems represented by equation
(5.1), the first eigenvalue of the associated homogeneous problem may be obtained from the
slope of the graph. In particular, the behavior of plates in the postbuckling regime is entirely
different from the hyperbolic relationship predicted by equation (5.8).
5.4.2 Spencer-Walker plots for plates
Walker showed that for rectangular plates over a wide range of aspect ratios, boundary
conditions and loading, a good approximation that is valid well into the postbuckling range is:
322 ~
ψψ BAh
Wh
W T
+=⎟⎟⎠
⎞⎜⎜⎝
⎛−⎟⎟
⎠
⎞⎜⎜⎝
⎛ (5.9)
where,
TC W
WPP ~
1+−=ψ (5.10)
h is the plate thickness, and A and B are constants [25].
For the particular experiments completed in the present work as CPP →
1~ <<TWW
ψψ <<3
Considering the previous results, Donnell [25] proposed the equation:
( )( )WW
AhWWWP
PC
~21~
112 ++
+=⎟
⎠⎞
⎜⎝⎛ (5.11)
which is a special case of equation (5.9) that is based on using a single term of a double-odd
61
Fourier series for the deflection with 0=B .
The following paragraphs describe the application of the previous concept to plates with
small imperfections and data extending into the postbuckling regime. The “pivot point concept”
will be introduced in equation (5.11) in order to parallel Southwell’s method and obtain a linear
equation whose slope coefficient provides the buckling load.
Equation (5.11) contains three unknown parameters: CPW ,~ , and A . The plot of equation
(5.11) can provide two pieces of information, slope and intercept, so one parameter remains
undetermined in this case. In order to overcome this limitation, the “pivot point concept” is
introduced, which is a generalization of common rectification techniques of fitting empirical
data. The name “pivot point” is given here to any piece of actual or faired-in data which, in the
judgment of the experimenter, is sufficiently accurate to deserve its introduction into an analysis
as if it were an extra equation. For example, the assumption of most experimenters that two-
dimensional phenomena start precisely at ( )0,0 actually constitutes a pivot point. The approach
is to substitute the values at the pivot point into the known equation and solve for one parameter.
This method provides an engineering technique for finding empirical constants in cases where
there are fewer equations than unknown constants. Its name was chosen to emphasize that the
accuracy of the consequent results “pivots” about the accuracy of the chosen pivot points [25].
Introduction of a pivot point ( )** ,WP into the Donnell equation (5.11) results in
( )( )WW
AhWWWP
PC
~21~
11 *2**
*
+++
=⎟⎟⎠
⎞⎜⎜⎝
⎛ (5.12)
A can be eliminated between equations (5.11) and (5.12) to give the plot equation:
62
( ) WHFPH C~
112 −= (5.13)
where,
( ) φ2*2*2 WPPWH −≡
( ) φ22*1 WWH −≡
2**
** 33 F
WWWP
WWPW ⎥
⎦
⎤⎢⎣
⎡⎟⎠⎞
⎜⎝⎛ +−⎟⎟
⎠
⎞⎜⎜⎝
⎛+≡φ
( )WWWF ++≡ *1
~31
( ) ( )( ) ( )*2*2**
*2**2**
233
33
WWWPWWWP
GWWWPGWWWPF+−+
++−++≡
( )[ ]WWWWG ~232~ ** ++≡
( )[ ]WWWWG ~232~ * ++≡
The proposed method is to assume at first that 121 == FF and to plot 2H versus 1H for
the data points. If a straight line results, its slope and intercept W~ can be measured, the
correction factor 1F estimated, and CP calculated.
5.4.3 Spencer-Walker plots for the panels tested
Equation (5.13) was plotted for the four panels tested (E, F, G, and H). Significant pivot
points were chosen for each panel, and the resulting points were found to very closely fit a
straight line. Resulting plots in Spencer-Walker format are shown in Figures 5.46 through 5.49.
The slopes of the linear regression lines provided the values of buckling loads listed in Table 5.1.
63
Laminate Buckling Load
(lbs) Buckling Load
(kN) Initial imperfection in the middle point (mm)
F (0) 15,598 69.38 0.0019
G (20) 16,366 72.80 -0.0147
H (45) 9,871 43.91 0.7202
E (90) 4,394 19.54 0.0004
Table 5.1 Summary of results from Spencer-Walker data reduction of ARAMIS measured out of
plane displacement.
64
0
5000
10000
15000
20000
25000
30000
35000
40000
45000
-7.00 -6.00 -5.00 -4.00 -3.00 -2.00 -1.00 0.00
Measured out of plane displacement (mm)
Actu
ator
Loa
d P
(lbs)
y = 15598x - 0.0147
-1.8
-1.6
-1.4
-1.2
-1
-0.8
-0.6
-0.4
-0.2
0
0.2
-0.00012 -0.0001 -0.00008 -0.00006 -0.00004 -0.00002 0 0.00002
H1 parameter
H2 p
aram
eter
Pivot PointP* = 19551W* = -2.570
Figure 5.46 - Laminate F (0 degree): ARAMIS measured out of plane displacement vs. load
(above), and same data in Spencer-Walker format (below)
65
0
5000
10000
15000
20000
25000
30000
35000
40000
45000
-0.70 -0.60 -0.50 -0.40 -0.30 -0.20 -0.10 0.00
Measured out of plane disp W (mm)
Actu
ator
Loa
d (lb
s)
y = 16366x + 5E-05
-0.018
-0.016
-0.014
-0.012
-0.01
-0.008
-0.006
-0.004
-0.002
0
0.002
-0.0000012 -0.000001 -0.0000008 -0.0000006 -0.0000004 -0.0000002 0
H1 parameter
H2 p
aram
eter
Pivot PointP* = 16328W* = -0.017
Figure 5.47 - Laminate G (20 degree): ARAMIS measured out of plane displacement vs. load
(above), and same data in Spencer-Walker format (below)
66
0
5000
10000
15000
20000
25000
0.00 1.00 2.00 3.00 4.00 5.00
Measured out of plane displacement W (mm)
Actu
ator
Loa
d (lb
s)
y = 9871.3x + 0.7202
0
0.2
0.4
0.6
0.8
1
1.2
1.4
0 0.00001 0.00002 0.00003 0.00004 0.00005 0.00006H1 parameter
H2 pa
ram
eter
Pivot PointP* = 27393W* = 2.93
Figure 5.48 - Laminate H (45 degree): ARAMIS measured out of plane displacement vs. load
(above), and same data in Spencer-Walker format (below)
67
0
5000
10000
15000
20000
25000
30000
35000
-14.00 -12.00 -10.00 -8.00 -6.00 -4.00 -2.00 0.00
Measured out of plane displacement W (mm)
Actu
ator
Loa
d P
(lbs)
y = 4393.7x + 0.0004
-0.014
-0.012
-0.01
-0.008
-0.006
-0.004
-0.002
0
0.002
-3.5E-06 -3E-06 -2.5E-06 -2E-06 -1.5E-06 -1E-06 -5E-07 0 5E-07
H1 parameter
H2 p
aram
eter
Pivot PointP* = 4243W* = -0.0123
Figure 5.49 - Laminate E (90 degree): ARAMIS measured out of plane displacement vs. load
(above), and same data in Spencer-Walker format (below)
68
CHAPTER SIX
6FINITE ELEMENT MODEL
Previous chapters introduced the general requirements for a finite element (FE) analysis
to accurately simulate nonlinear buckling and progressive failure. This chapter describes the
specific modeling features that were introduced in the process of building the models used in this
dissertation. The finite element models used were created and analyzed in ANSYS v.10 and in
ABAQUS v.6.6, which incorporate their own pre/postprocessors. The models included the
features listed in Table 6.1.
As a brief reminder, the general methodology of the analysis portion of this dissertation
can be summarized as follows. First, run the linearized FE analysis to obtain the lowest buckling
loads and modes, where the lowest buckling load should be a reasonably good estimate of the
critical buckling load. As indicated previously, this estimate will only be reliable if the pre-
buckling displacements are small and the stresses vary linearly with the load. Second, using the
lowest mode shapes or the perturbation force method, an initial geometric imperfection can be
defined and introduced in the nonlinear analysis. If initial imperfections are imposed on the
“perfect” geometry of the structure, the load versus deflection results from the model should be a
closer match with the actual physical structure. Third, obtain the nonlinear solution with
imperfection to characterize the structural response in full, with stresses, strains and
displacements. When the solution includes progressive failure analysis (PFA) a cut-off level of
load associated with the first occurring failure of several potential modes of damage will indicate
the maximum design loading.
69
Component ANSYS element
type
ABAQUS
element type
Section
Panel (carbon/Epoxy and
glass/Epoxy)
SHELL 181 S4 (large strain
shell)
Laminated shell, different lay-ups
Picture frame arms (Steel) BEAM 44 B31 (3D beam) Rectangular, 1.1 x 3.0
Table 6.1 FE modeling features. Element types, boundary conditions and loads
Figure 6.1 ABAQUS FE model view. Picture frame and panel
Feature Modeled as
Actuator pull load Forces Fx, Fy on top right corner, equal in magnitude
Picture frame hinges Built by duplicating coincident nodes. Constrain Equation to have same
Ux, Uy, Uz, Rx, and Ry on coincident nodes
Nodal constraints Ux, Uy, Uz set to zero on lower left hinge
70
6.1 Modeling the composite panels
Based on the findings of Hermann et al. [4], the ANSYS SHELL181 is the element of
choice for postbuckling simulation. It is formulated for large rotations and/or large strain
nonlinear applications such as postbuckling.
It is a four-node element with six degrees of freedom per node: Cartesian x, y, z
translations and rotations about the x, y, z axes. Its formulation is based on the first order shear
deformation theory. This element supports both full and reduced integration schemes. The
assumptions and restrictions for the element are as follows [9]. This element works best with a
full Newton-Raphson solution scheme. Shear deflections are included in the element
formulation; however, sections normal to the center plane before deformation are assumed to
remain straight after deformation. For a composite laminate, this translates into the assumption
of no slippage between the element layers. This is standard first order shear deformation plate
theory. The usage of reduced integration (KEYOPTION 3 = 0 in ANSYS SHELL181) is
generally recommended to avoid the occurrence of shear locking, which is common in first order
shear deformation elements. However, SHELL181 includes incompatible modes capability,
which avoids shear locking. For elements that have large strain capability, the output stresses are
true (Cauchy) stresses in the rotated element coordinate system (the element coordinate system
follows the material as it rotates). Strain outputs are the logarithmic or Hencky strains, also in the
rotated element coordinate system.
In ABAQUS 6.6 the S4 element was used to model the laminates. Element type S4 is a
fully integrated, general-purpose, finite-membrane-strain shell element available in
ABAQUS/Standard. The element's membrane response is treated with an assumed strain
71
formulation that gives accurate solutions to in-plane bending problems, is not sensitive to
element distortion, and avoids parasitic locking. Element type S4 does not have hourglass modes
in either the membrane or bending response of the element; hence, the element does not require
hourglass control. The element has four integration locations per element, which makes the
element computationally expensive. S4 can be used for problems prone to membrane- or
bending-mode hourglassing, in areas where greater solution accuracy is required, or for problems
where in-plane bending is expected.
6.2 Modeling the picture frame arms
The element chosen to model the picture frame arms in ANSYS is BEAM44 3-D Elastic
Beam, which allows for large rotations. Shear effects are not included by default (but can be
included as an option). BEAM44 was chosen after running a quick study to compare solutions
using BEAM44 against solutions using BEAM4 Elastic Beam and BEAM188 Finite Strain Beam
as shown in Table 6.2.The BEAM4 elastic beam element is formulated for Classical Beam
Theory and does not allow for finite strains or large displacements. Elements belonging to the
180 series (BEAM188 and BEAM189) allow for large rotations and strains and they include
shear effects by default.
The interpretation of these results is that although the frame arms do not undergo finite
strains since they are very stiff compared to the plate, they still experience large rotations around
the hinges of the fixture for some of the panels. For large rotation cases, the BEAM4 element
presented convergence difficulties. The BEAM188 includes shear effects by default, which
makes the execution cumbersome and results in a very stiff element. The BEAM44 element
proved to have the most robust convergence properties while still not being too stiff. For the
72
stated reasons, the element chosen to model the Picture Frame fixture was the BEAM44.
Buckling Load, Non Linear Analysis (lbs)
Panel BEAM4 BEAM44 BEAM188
Laminate 20 deg 13,545 14,059 27,256
Laminate 45 deg 8,060 8,840 21,731
Laminate 90 deg Not converged 4,526 15,788
Laminate 0 deg Not converged 20,489 47,354
Table 6.2 Comparison of results. Different picture frame modeling options (ANSYS)
In ABAQUS 6.6 the beams were modeled using the B31 two-node linear 3D beam
element. This choice of element did not pose any difficulties.
6.3 Mechanical properties of the laminates tested
As stated previously, the laminates tested consisted of alternating plies of pre impregnated
Double Biax Glass/Epoxy (denoted as DB) with plies of pre impregnated Unidirectional
Carbon/Epoxy tape (denoted as UC). The basic laminate followed the symmetric sequence
[ ]SUCDBUCDB ,,, . For all of the laminates, fibers of the DB layers are oriented at 45 degrees
with respect to the fibers of the UC layers. The material properties of the DB layer were tested
and reported in the ply axes. Therefore, every DB layer was modeled as a single orthotropic layer
in the SHELL 181 (and ABAQUS S4) layered element.
The ANSYS section plot, shown in Figure 6.2, has a fictitious fiber direction for the DB
73
layers parallel to the direction of the fiber in the UC layers. The material properties of the plies
used to build the laminates exhibit the mechanical properties listed in Table 6.3.
Figure 6.2 ANSYS section plot of the laminate for the case of zero degree with the direction of
the load.
Note that in Figure 6.2 the colored lines represent the axes of the ply. The fibers in the
DB layers are oriented at 45 degrees with respect to the ply axes.
74
Double Biax Glass Fabric (12 oz/yd2)
Unidirectional Carbon Fabric (15 oz/yd2)
Material MGDB12 MCUD15
Laminate Thickness (in) 0.152 0.110
E1 (lbf/in2) 1.610E+06 1.846E+07
E2 (lbf/in2) 1.610E+06 1.273E+06
E3 (lbf/in2) 1.610E+05 1.273E+05
V12 0.604 0.328
V23 0.360 0.360
V13 0.360 0.360
V21 0.604 0.023
V32 0.036 0.036
V31 0.036 0.002
G23 (lbf/in2) 1.639E+05 1.639E+05
G31 (lbf/in2) 1.639E+05 1.639E+05
G12 (lbf/in2) 1.461E+06 7.359E+05
Fiber Density (lbm/in3) 0.0939 0.0650
Fiber Density (slug/in3) 2.919E-03 2.021E-03
Nominal Density (lbm/in3) 0.0664 0.0562
Nominal Density (slug/in3) 2.064E-03 1.747E-03
Dry Material Weight (oz/yd2) 12 15
Dry Material Weight (oz/in2) 9.259E-03 1.157E-02
Table 6.3 Mechanical properties of individual plies (British Units)
75
CHAPTER SEVEN
7ANALYTICAL CLASSICAL SOLUTIONS
This chapter presents approximate analytical results for the linear buckling loads for each
of the laminates tested. These solutions were developed as a baseline estimate for the detailed
finite element solutions. It should be noted that until recently, analytical solutions were
considered to be the standard method to calculate the buckling load of composite panels with
different boundary conditions and loading; e.g., four clamped edges under shear load. In fact,
most in-house structural design manuals rely on analytical solutions that have been validated by
test data. For the panels considered herein, the combination of laminate stiffness properties
combined with the boundary conditions and loading does not permit an exact analytical solution;
therefore, an approximate solution has been obtained using the Raleigh-Ritz technique [22]. The
validity of the approximate solution is limited to specially orthotropic laminates, such that all
elements of the B sub-matrix and the D16 and D26 elements of the D sub-matrix are zero, where
B and D are sub-blocks of the laminate stiffness matrix derived from the Classical Laminated
Plate Theory (CLPT).
The CLPT stiffness matrix was calculated for each laminate using the software package
ESAComp, which shows that only one of the panels (laminate 45 degree) included in this
research complies with the specially orthotropic condition. Even so, a two-term Raleigh-Ritz
solution was obtained to gain insight regarding the order of magnitude to expect for the buckling
load. The results are given in the following figures. Figures 7.1 through 7.4 show the stiffness
matrices of each laminate as directly output from ESAComp script. Figures 7.7 through 7.10
show the calculation of the buckling load based on the two-term Raleigh-Ritz solution provided
76
by Reddy [22]. Table 7.1 shows a summary of results obtained from the analytical solution.
Laminate : Laminate_0deg_08-2005
Modified : Mon May 08 20:37:11 2006
Lay-up
(+45a/+45b/+45a/+45b/+45b/+45a/+45b/+45a)
Ply t (mm)
a Double Bias Glass +-45 (12 oz/yd2) 0.329b Unidirectional Carbon (15 oz/yd2) 0.487
n = 8 m_A = 6928 g/m²h = 3.264 mm rho = 2123 kg/m³
Classification
Ply types : Solid;Reinf.Lay-up : Symm.
Constit. beh. : AeBoDe
1 a 45°
2 b 45°
3 a 45°
4 b 45°
5 b 45°
6 a 45°
7 b 45°
8 a 45°
Laminate stiffness and compliance matrices
Laminate : Laminate_0deg_08-2005
Stiffness matrix
[A] [B] (N/m) (N) [B] [D] (N) (Nm)
1.11183e+008 6.48842e+007 5.81521e+007 0 0 06.48842e+007 1.11183e+008 5.81521e+007 0 0 05.81521e+007 5.81521e+007 6.84933e+007 0 0 0
0 0 0 89.6925 43.183 35.51230 0 0 43.183 89.6925 35.51230 0 0 35.5123 35.5123 44.9573
Compliance matrix
[a] [b] (m/N) (1/N) [b]^T [d] (1/N) (1/(Nm))
1.72658e-008 -4.33301e-009 -1.09802e-008 0 0 0-4.33301e-009 1.72658e-008 -1.09802e-008 0 0 0-1.09802e-008 -1.09802e-008 3.32447e-008 0 0 0
0 0 0 0.0172633 -0.00423774 -0.0102890 0 0 -0.00423774 0.0172633 -0.0102890 0 0 -0.010289 -0.010289 0.0384982
Figure 7.1 Laminate 0 degree. Lay-up and stiffness matrices
77
Laminate : Laminate_20deg_08-2005
Modified : Mon May 08 21:10:59 2006
Lay-up
(+65a/+65b/+65a/+65b/+65b/+65a/+65b/+65a)
Ply t (mm)
a Double Bias Glass +-45 (12 oz/yd2) 0.329b Unidirectional Carbon (15 oz/yd2) 0.487
n = 8 m_A = 6928 g/m²h = 3.264mm rho = 2123 kg/m³
Classification
Ply types : Solid;Reinf.Lay-up : Symm.
Constit. beh. : AfBoDf
1 a 65°
2 b 65°
3 a 65°
4 b 65°
5 b 65°
6 a 65°
7 b 65°
8 a 65°
Laminate stiffness and compliance matrices
Laminate : Laminate_20deg_08-2005
Stiffness matrix
[A] [B] (N/m) (N)
[B] [D] (N) (Nm)
5.51592e+007 4.61492e+007 2.22196e+007 0 0 04.61492e+007 2.04677e+008 6.68745e+007 0 0 02.22196e+007 6.68745e+007 4.97583e+007 0 0 0
0 0 0 53.0057 34.216 16.51760 0 0 34.216 144.313 37.89050 0 0 16.5176 37.8905 35.9903
Compliance matrix
[a] [b] (m/N) (1/N)
[b]^T [d] (1/N) (1/(Nm))
2.32956e-008 -3.30494e-009 -5.96087e-009 0 0 0-3.30494e-009 9.1798e-009 -1.08617e-008 0 0 0-5.96087e-009 -1.08617e-008 3.7357e-008 0 0 0
0 0 0 0.0234117 -0.00377252 -0.006772990 0 0 -0.00377252 0.0101844 -0.008990710 0 0 -0.00677299 -0.00899071 0.0403591
Figure 7.2 Laminate 20 degrees. Lay-up and stiffness matrices
78
Laminate : Laminate_45deg_08-2005
Modified : Mon May 08 21:29:50 2006
Lay-up
(90a/90b/90a/90b/90b/90a/90b/90a)
Ply t (mm)
a Double Bias Glass +-45 (12 oz/yd2) 0.329b Unidirectional Carbon (15 oz/yd2) 0.487
n = 8 m_A = 6928 g/m²h = 3.264mm rho = 2123 kg/m³
Classification
Ply types : Solid;Reinf.Lay-up : Symm.;Cross-ply
Constit. beh. : AsBoDs
1 a 90°
2 b 90°
3 a 90°
4 b 90°
5 b 90°
6 a 90°
7 b 90°
8 a 90°
Laminate stiffness and compliance matrices
Laminate : Laminate_45deg_08-2005
Stiffness matrix
[A] [B] (N/m) (N) [B] [D] (N) (Nm)
4.02228e+007 1.95404e+007 0 0 0 01.95404e+007 2.72831e+008 0 0 0 0
0 0 2.31494e+007 0 0 00 0 0 40.3704 21.4804 00 0 0 21.4804 182.42 00 0 0 0 0 23.2547
Compliance matrix
[a] [b] (m/N) (1/N)
[b]^T [d] (1/N) (1/(Nm))
2.57577e-008 -1.84479e-009 0 0 0 0-1.84479e-009 3.7974e-009 0 0 0 0
0 0 4.31976e-008 0 0 00 0 0 0.0264263 -0.00311178 00 0 0 -0.00311178 0.00584829 00 0 0 0 0 0.043002
Figure 7.3 Laminate 45 degrees. Lay-up and stiffness matrices
79
Laminate : Laminate_90deg_08-2005
Modified : Mon May 08 21:34:36 2006
Lay-up
(-45a/-45b/-45a/-45b/-45b/-45a/-45b/-45a)
Ply t (mm)
a Double Bias Glass +-45 (12 oz/yd2) 0.329b Unidirectional Carbon (15 oz/yd2) 0.487
n = 8 m_A = 6928 g/m²h = 3.264mm rho = 2123 kg/m³
Classification
Ply types : Solid;Reinf.Lay-up : Symm.
Constit. beh. : AfBoDe
1 a -45°
2 b -45°
3 a -45°
4 b -45°
5 b -45°
6 a -45°
7 b -45°
Laminate stiffness and compliance matrices
Laminate : Laminate_90deg_08-2005
Stiffness matrix
[A] [B] (N/m) (N) [B] [D] (N) (Nm)
1.11183e+008 6.48842e+007 -5.81521e+007 0 0 06.48842e+007 1.11183e+008 -5.81521e+007 0 0 0
-5.81521e+007 -5.81521e+007 6.84933e+007 0 0 00 0 0 89.6925 43.183 -35.51230 0 0 43.183 89.6925 -35.51230 0 0 -35.5123 -35.5123 44.9573
Compliance matrix
[a] [b] (m/N) (1/N) [b]^T [d] (1/N) (1/(Nm))
1.72658e-008 -4.33301e-009 1.09802e-008 0 0 0-4.33301e-009 1.72658e-008 1.09802e-008 0 0 01.09802e-008 1.09802e-008 3.32447e-008 0 0 0
0 0 0 0.0172633 -0.00423774 0.0102890 0 0 -0.00423774 0.0172633 0.010289
Figure 7.4 Laminate 90 degree. Lay-up and stiffness matrices
80
P 1.866 104×=
P Nxy 12⋅ 2⋅:=a22 526.588=
Nxy 1.1 103×=a12 0.16=
a11 59.149=Nxya11 a22⋅
a12:=
a223791.532 D11⋅
a4
4227.255 D12 2 D66⋅+( )⋅
a2 b2⋅+
3791.532 D22⋅
b4+:=
a1223.107
a b⋅:=
a11537.181 D11⋅
a4
324.829 D12 2 D66⋅+( )⋅
a2 b2⋅+
537.181 D22⋅
b4+:=
Ritz two terms approximation (Reddy, [8])
D66 395.004=
D12 379.414=
D22 788.056=D66 Di66 0.223⋅ 39.4⋅:=
D11 788.056=D22 Di22 0.223⋅ 39.4⋅:=
D12 Di12 0.223⋅ 39.4⋅:=
D11 Di11 0.223⋅ 39.4⋅:=
Transform Matrix D to English Units
Di66 44.9573:=
Di22 89.6925:=
Di12 43.1830:=b 12:=
a 12:=Di11 89.6925:=
Matrix D of the laminate in SI units:
Laminate 0 degrees
Figure 7.5 Laminate 0 degree. Buckling load calculation, two-term Ritz approx.
81
P 1.838 104×=
P Nxy 12⋅ 2⋅:=a22 507.214=
Nxy 1.083 103×=a12 0.16=
a11 59.529=Nxya11 a22⋅
a12:=
a223791.532 D11⋅
a4
4227.255 D12 2 D66⋅+( )⋅
a2 b2⋅+
3791.532 D22⋅
b4+:=
a1223.107
a b⋅:=
a11537.181 D11⋅
a4
324.829 D12 2 D66⋅+( )⋅
a2 b2⋅+
537.181 D22⋅
b4+:=
Ritz two terms approximation (Reddy, [8])
D66 316.215=
D12 300.629=
D22 1.268 103×=D66 Di66 0.223⋅ 39.4⋅:=
D11 465.721=D22 Di22 0.223⋅ 39.4⋅:=
D12 Di12 0.223⋅ 39.4⋅:=
D11 Di11 0.223⋅ 39.4⋅:=
Transform Matrix D to English Units
Di66 35.990:=
Di22 144.313:=
Di12 34.216:=b 12:=
a 12:=Di11 53.006:=
Matrix D of the laminate in SI units:
Laminate 20 degrees
Figure 7.6 Laminate 20 degrees. Buckling load calculation, two-term Ritz approx.
82
P 1.828 104×=
P Nxy 12⋅ 2⋅:=a22 490.449=
Nxy 1.077 103×=a12 0.16=
a11 60.894=Nxya11 a22⋅
a12:=
a223791.532 D11⋅
a4
4227.255 D12 2 D66⋅+( )⋅
a2 b2⋅+
3791.532 D22⋅
b4+:=
a1223.107
a b⋅:=
a11537.181 D11⋅
a4
324.829 D12 2 D66⋅+( )⋅
a2 b2⋅+
537.181 D22⋅
b4+:=
Ritz two terms approximation (Reddy, [8])
D66 230.679=
D12 188.731=
D22 1.603 103×=D66 Di66 0.223⋅ 39.4⋅:=
D11 354.702=D22 Di22 0.223⋅ 39.4⋅:=
D12 Di12 0.223⋅ 39.4⋅:=
D11 Di11 0.223⋅ 39.4⋅:=
Transform Matrix D to English Units
Di66 26.2547:=
Di22 182.420:=
Di12 21.4804:=b 12:=
a 12:=Di11 40.3704:=
Matrix D of the laminate in SI units:
Laminate 45 degrees
Figure 7.7 Laminate 45 degrees. Buckling load calculation, two-term Ritz approx.
83
P 1.866 104×=
P Nxy 12⋅ 2⋅:=a22 526.588=
Nxy 1.1 103×=a12 0.16=
a11 59.149=Nxya11 a22⋅
a12:=
a223791.532 D11⋅
a4
4227.255 D12 2 D66⋅+( )⋅
a2 b2⋅+
3791.532 D22⋅
b4+:=
a1223.107
a b⋅:=
a11537.181 D11⋅
a4
324.829 D12 2 D66⋅+( )⋅
a2 b2⋅+
537.181 D22⋅
b4+:=
Ritz two terms approximation (Reddy, [8])
D66 395.004=
D12 379.414=
D22 788.056=D66 Di66 0.223⋅ 39.4⋅:=
D11 788.056=D22 Di22 0.223⋅ 39.4⋅:=
D12 Di12 0.223⋅ 39.4⋅:=
D11 Di11 0.223⋅ 39.4⋅:=
Transform Matrix D to English Units
Di66 44.9573:=
Di22 89.6925:=
Di12 43.183:=b 12:=
a 12:=Di11 89.6925:=
Matrix D of the laminate in SI units:
Laminate 90 degrees
Figure 7.8 Laminate 90 degrees. Buckling load calculation, two-term Ritz approx.
84
Laminate Buckling Load (lbs)
0 degree 18,660
20 degree 18,380
45 degree 18,280
90 degree 18,660
Table 7.1 Summary of results. Buckling load calculation, two-term Ritz approx.
Inspection of Table 7.1 reveals the limited validity of this kind of solution. It is useful to
provide a first cut of the value of the buckling load. The details of this approximate analysis are
listed in the following paragraphs.
The governing equation for a specially orthotropic laminate under shear load, 0xyN , is
given as
( )yx
wN
yw
Dyx
wDD
xw
D xy ∂∂∂
=∂∂
+∂∂
∂++
∂∂ 0
20
40
4
22220
4
661240
4
11 222 (7.1)
This problem does not permit the Navier solution; therefore, an approximate solution has been
obtained using the Rayleigh Ritz method. For the case of the clamped plate (like the panels
considered herein) the total potential energy expression for the case of in-plane shear loading is:
85
( )
dxdyy
wx
wN
yw
D
yxw
Dyw
xw
Dxw
Dw
xy
b a
⎥⎥⎦
⎤⎟⎟⎠
⎞⎜⎜⎝
⎛∂∂
∂∂
−⎟⎟⎠
⎞⎜⎜⎝
⎛∂∂
+
⎢⎢⎣
⎡+⎟⎟
⎠
⎞⎜⎜⎝
⎛∂∂
∂+⎟⎟
⎠
⎞⎜⎜⎝
⎛∂∂
∂∂
+⎟⎟⎠
⎞⎜⎜⎝
⎛∂∂
=Π ∫ ∫
0002
20
2
22
2
02
6620
2
20
2
12
2
20
2
110 00
2
4221
(7.2)
The minimum total potential energy principle requires that 0=Πδ , which results in
( ) ( ) ( )( )
dxdyyw
xw
yw
xw
Nyw
yw
D
yxw
yxw
Dyw
xw
xw
yw
Dxw
xw
D
dxdywqMMM
xy
b a
xyxyyyyyxxxx
b a
⎥⎥⎦
⎤⎟⎟⎠
⎞⎜⎜⎝
⎛∂
∂∂∂
+∂∂
∂∂
−⎟⎟⎠
⎞⎜⎜⎝
⎛∂∂
∂∂
+
⎢⎢⎣
⎡+⎟⎟
⎠
⎞⎜⎜⎝
⎛∂∂
∂∂∂
∂+⎟⎟
⎠
⎞⎜⎜⎝
⎛∂∂
∂∂
+∂∂
∂∂
+⎟⎟⎠
⎞⎜⎜⎝
⎛∂∂
∂∂
=
=−++=
∫ ∫
∫ ∫
000002
02
20
2
22
02
02
6620
2
20
2
20
2
20
2
1220
2
20
2
110 0
0111
0 0
4
0
δδδ
δδδδ
δδγδεδε
(7.3)
A Ritz approximation of the following form is assumed
( ) ( ) ( )yxcyxWyxw ij
m
i
n
jijmn ,,,
1 10 ϕ∑∑
= =
=≈ (7.4)
where
( ) ( ) ( )yYxXyx iiij =,ϕ (7.5)
with
( ) ( )2121
1,1 ⎟⎠⎞
⎜⎝⎛ −⎟
⎠⎞
⎜⎝⎛=⎟
⎠⎞
⎜⎝⎛ −⎟
⎠⎞
⎜⎝⎛=
++
by
byyY
ax
axxX
j
j
i
i (7.6)
or
( ) ( ) ( ) ( ) ( )( )( ) ( ) ( ) ( ) ( )( )yyyyxY
xxxxxX
jjjjjj
iiiiii
λλαλλλλαλλ
coscoshsinhsincoscoshsinhsin−+−=−+−=
(7.7)
86
for mi ,...,2,1= ; nj ,...,2,1= . The parameters iλ and iα of the previous equations are obtained
from solving the characteristic equation, and come defined as:
( )2
12,853.7,730.4 21πλλλ +≈== iaaa iL
21,99922.0,0178.1 21 >=== iforiααα L
Substituting the Ritz approximation into the total potential energy equation results in:
( )
pqqpj
iq
pji
xyq
pj
i
qpjiq
pj
ib a
cdxdyYdx
dYdydY
Xdy
dYXY
dxdX
Ndy
YdX
dyYd
XD
dydY
dxdX
dydY
dxdX
DDYdx
XdY
dxXd
D
⎪⎭
⎪⎬⎫
⎥⎥⎦
⎤⎟⎟⎠
⎞⎜⎜⎝
⎛+−+
⎪⎩
⎪⎨⎧
⎢⎢⎣
⎡+++⎟
⎟⎠
⎞⎜⎜⎝
⎛= ∫ ∫
02
2
2
2
22
66122
2
2
2
110 0220
(7.8)
When the functions ( )xX i and ( )yYj are used, at least two terms are required because
the coefficient of 0xyN is zero for 1== nm ; other coefficients are zero for 2,1 == nm and
1,2 == nm . Using the approximation
( ) ( ) ( ) ( ) ( )yYxXcyYxXcyxw 222211110 , +≈ (7.9)
with the expressions
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛⎟⎠⎞
⎜⎝⎛−⎟
⎠⎞
⎜⎝⎛+⎟
⎠⎞
⎜⎝⎛−⎟
⎠⎞
⎜⎝⎛=
ax
ax
ax
axxX 73.4cos73.4cosh0178.173.4sinh73.4sin1 (7.10)
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛⎟⎠⎞
⎜⎝⎛−⎟
⎠⎞
⎜⎝⎛+⎟
⎠⎞
⎜⎝⎛−⎟
⎠⎞
⎜⎝⎛=
ax
ax
ax
axxX 853.7cos853.7cosh9992.0853.7sinh853.7sin2
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛⎟⎠⎞
⎜⎝⎛−⎟
⎠⎞
⎜⎝⎛+⎟
⎠⎞
⎜⎝⎛−⎟
⎠⎞
⎜⎝⎛=
by
by
by
byyY 73.4cos73.4cosh0178.173.4sinh73.4sin1
87
( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛⎟⎠⎞
⎜⎝⎛−⎟
⎠⎞
⎜⎝⎛+⎟
⎠⎞
⎜⎝⎛−⎟
⎠⎞
⎜⎝⎛=
by
by
by
byyY 853.7cos853.7cosh9992.0853.7sinh853.7sin2
results in
( ) 0107.23181.5372829.324181.53722
0112236612113 =−⎥⎦
⎤⎢⎣⎡ +++ cNcD
baDD
abD
ab
xy
( ) 0107.23181.5372255.4227532.379111
0222236612113 =−⎥⎦
⎤⎢⎣⎡ +++ cNcD
baDD
abD
ab
xy
or in matrix form,
⎭⎬⎫
⎩⎨⎧
−=⎭⎬⎫
⎩⎨⎧
⎥⎥⎦
⎤
⎢⎢⎣
⎡
00
22
11
22120
120
11
cc
aaNaNa
xy
xy (7.11)
where
( ) 0107.23181.5372829.324181.53722
01122366122211411 =−⎥⎦
⎤⎢⎣⎡ +++= cNcD
bDD
baD
aa xy ab
a 107.2312 =
For a nontrivial solution, the determinant of the coefficient matrix should be zero:
( ) 0012122211 =− xyNaaaa
Solving for the buckling load ( )0xyN ,
221112
0 1 aaa
N xy ±= (7.12)
The ± sign indicates that the shear buckling load can be either positive or negative. For
an isotropic square plate, we would have:
ba =
88
( ) DDDDD =+== 66122211 2
and the shear buckling loads are:
20 176
aDN xy ±=
89
CHAPTER EIGHT
8LINEARIZED BUCKLING ANALYSIS
8.1 Formulation
The algorithm to obtain the linearized buckling load is described in this section.
Considering the matrix form of the system of equations assembled by the finite element (FE)
solver algorithm, the tangent stiffness matrices at times t and ( )tt Δ+ are denoted as tK and
ttK Δ+ , and the corresponding vectors of externally applied loads are tR and ttR Δ+ . In linearized
buckling analysis, it is assumed that at any time τ
( )tttt KKKK −+= Δ+λτ
and the applied load vector is:
( )tttt RRRR −+= Δ+λτ
where λ is a scaling factor and those values of λ which are greater than one are of interest. At
collapse or buckling the tangent stiffness matrix is singular and hence the condition for
calculating λ is
( ) 0det =τK
or, equivalently
0=φτK
where φ is a nonzero vector. Combining the previous equations yields the eigenproblem
( )φλφ tttt KKK Δ+−=
90
The eigenvalues iλ , for ni ,....1= give the buckling loads and the eigenvectors iφ
represent the corresponding buckling modes. It is assumed that the matrices tK and ttK Δ+ are
both positive definite but in general the difference matrix ( )ttt KK Δ+− is indefinite; hence, the
eigenproblem will have both positive and negative solutions and some eigenvalues will be
negative. Negative eigenvalues can be ignored, and the smallest positive eigenvalues are the only
ones desired. The last equation can be rewritten as
( )φγφ ttt KK =Δ+
λλγ 1−
=
The eigenvalues iγ are all positive and usually only the smallest values 1γ , 2γ … are of
interest. Namely, 1γ corresponds to the smallest value of λ in the original problem. Once 1γ is
known, 1λ is also known and the buckling load is given by:
( )ttttbuckling RRRR −+= Δ+1λ
Similarly, the buckling loads associated with the remaining iγ for 1>i can be evaluated.
In practice, most frequently 0=t (initial configuration with 00 =R ) and tΔ is the first load step
with tRΔ ; however, these equations are applicable to any load step prior to buckling.
8.2 Analysis results
The linearized ANSYS buckling analysis executed the eigenbuckling solution using
block Lanzcos, and the first three eigenvalues and buckling modes were requested. Once the
lowest eigenvalues are known, the buckling load was calculated as
91
appiicr FP λ=,
where iλ is the eigenvalue i ,
icrP , is the critical or buckling load associated with the eigenvalue i
appF is the load applied to the model in order to run the linearized analysis.
It should be noted that ANSYS does not automatically perform the initial linear static
analysis necessary to determine the geometric stiffness matrix. Therefore, the analyst should first
run the linear static solution for the model with the option “Calculate pre-stress effects” turned
on. Once the linear solution is known, the eigenbuckling analysis should be ran from the same
folder using the Block Lanzcos factorization scheme.
8.2.1 Laminate F - 0 degree with the direction of the load
The lay-up sequence of this laminate is shown in Figure 8.1. All of the plies of the
laminate form the same angle with the direction of the load. Table 8.1 lists the results of the
linearized buckling analysis for this panel.
Load Applied for Analysis (lbs)
First Eigenvalue/ Buckling Load (lbs)
Second Eigenvalue/ Buckling Load (lbs)
Third Eigenvalue/ Buckling Load (lbs)
2.1838 2.2522 31.214 1,000
21,838 22,522 31,214
21.838 22.522 4.7456 10,000
21,838 22,522 47,456
1.0919 1.1261 2.3728 20,000
21,838 22,522 47,456
Table 8.1 Eigenvalues and buckling loads vs. level of load applied to the model
92
Figure 8.1 Laminate 0 degree, section plot.
Note that in Figure 8.1 the colored lines represent the axes of the ply. The fibers in the
DB layers are oriented at 45 degrees with respect to the ply axes..
From the previous table it can be concluded that the level of the load applied to the model
for the linearized analysis has little or no influence on the calculated critical buckling loads.
Figure 8.2 First mode, buckling load lbsP 838,21= . Out of plane displacement
93
Figure 8.3 Second mode, buckling load lbsP 522,22= . Out of plane displacement
Figure 8.4 Third mode, buckling load lbsP 456,47= . Out of plane displacement
94
From the observation of the previous three figures, as well as the behavior of the panels
during the test, it can be concluded that the third and subsequent modes are unrealistic and do not
add any value to the analysis. Therefore, only the first three buckling modes are requested for the
linearized analyses.
The first buckling mode exhibits a central out of plane narrow bubble together with two
very shallow bubbles on both sides that are opposite in direction. This shape denotes how the
presence of the unidirectional carbon plies in the direction of the load reduces the relative
stiffness of the laminate in the compression direction at -45 degrees with respect to the horizontal
axis, allowing the formation of the “negative” bubble on both sides (blue) and allowing the
laminate “to wrinkle” in that direction. The second mode is antisymmetric with two identical
bubbles in opposite directions.
The buckling load associated with the second mode is very close to the one of the first
mode. Therefore, the possibility of either the first or second mode occurring first and dominating
the actual test displacements should be considered.
8.2.2 Laminate G – 20 degree with the direction of the load
The lay-up sequence of this laminate is shown in Figure 8.5. All of the plies of the
laminate form the same angle with the direction of the load. Table 8.2 lists the results of the
linearized buckling analysis for this panel. Note that in Figure 8.5 the colored lines represent the
axes of the ply. Fibers in the DB layers are oriented at 45 degrees with respect to the ply axes.
95
Figure 8.5 Laminate 20 degree section plot.
Load Applied for Analysis (lbs)
First Eigenvalue/ Buckling Load
Second Eigenvalue/ Buckling Load
Third Eigenvalue/ Buckling Load
0.0002 157.07 163.42 100
0.02 15,707 16,342
0.0406 15.681 16.335 1,000
40,63 15,681 16,335
1.5681 1.6335 3.4489 10,000
15,681 16,335 34,489
1.5681 1.6335 3.4489 15,000
15,681 16,335 34,489
Table 8.2 Eigenvalues and buckling loads vs. level of load applied to the model
Table 8.2 shows that the level of the load applied to the model for the linearized analysis
has little or no influence on the calculated critical buckling loads. However, it can still be
observed that, as the applied load gets closer to the buckling load, some spurious solutions
96
present at lower levels tend to disappear, which is always desirable.
Figure 8.6 First mode, buckling load lbsP 681,15= . Out of plane displacement
Figure 8.7 Second mode, buckling load lbsP 335,16= . Out of plane displacement
97
Figure 8.8 Third mode, buckling load lbsP 489,34= . Out of plane displacement
As mentioned for the previous panel, only the first three buckling modes were requested
in the linearized analyses. All of the previous general comments for describing the mode shapes
of the 0 degree panel are also applicable for the 20 degree panel.
It can also be noted that the 20 degree lay-up produces a rotation in the orientation of the
buckling “bubbles” of the mode shapes. The nodal line that divides the semi sine waves in the
second mode appears rotated about 20 degrees in the positive direction. The same observation is
valid for the first and third modes.
Compared to the 0 degree laminate the 20 degree laminate has a decrease in the buckling
load of 40%.
8.2.3 Laminate H – 45 degree with the direction of the load
The lay-up sequence of this laminate is shown in Figure 8.9. Table 8.3 lists the results of
98
the linearized buckling analysis for this panel. Note that in Figure 8.9 the colored lines represent
the axes of the ply. The fibers in the DB layers are oriented at 45 degrees with respect to the ply
axes.
Figure 8.9 Laminate section plot. Lam 45 deg.
Load Applied for
Analysis (lbs)
First Eigenvalue/
Buckling Load
Second Eigenvalue/
Buckling Load
Third Eigenvalue/
Buckling Load
0.0041 16.012 20.508 100
0.41 1,601 2,051
9.4980 10.174 18.083 1,000
9,498 10,174 18,083
0.94980 1.0174 1.8083 10,000
9,498 10,174 18,083
Table 8.3 Eigenvalues and buckling loads vs. level of load applied to the model
Table 8.3 shows that the level of the load applied to the model for the linearized analysis
99
has little or no influence on the calculated critical buckling loads. It can still be observed that, as
the applied load gets closer to the buckling load, some spurious solutions present at lower levels
disappear.
Figure 8.10 First mode, buckling load lbsP 498,9= . Out of plane displacement
Figure 8.11 Second mode, buckling load lbsP 147,10= . Out of plane displacement
100
Figure 8.12 Third mode, buckling load lbsP 083,18= . Out of plane displacement
Only the first three buckling modes were requested in the linearized analyses. All of the
general comments for describing the mode shapes of the 0 and 20 degree panels are also
applicable for the 45 degree panel. The 45 degree lay-up causes a rotation in the orientation of
the buckling “bubbles” of the mode shapes. The nodal line that divides the semi sine waves in
the second mode appears rotated about 45 degrees in the positive direction. This same
observation is valid for the first and third modes. It also can be concluded that the 45 degree
laminate has a decrease in the buckling load of 130% with respect to the 0 degree laminate.
8.2.4 Laminate E – 90-degree with the direction of the load
The lay-up sequence of this laminate is shown in Figure 8.13. Table 8.4 lists the results of
the linearized buckling analysis for this panel. Note that in Figure 8.13 the colored lines
101
represent the axes of the ply. Fibers in the DB layers are oriented at 45 degrees with respect to
the ply axes.
Figure 8.13 Laminate section plot. Lam 90 deg.
Load Applied for
Analysis (lbs)
First Eigenvalue/
Buckling Load
Second Eigenvalue/
Buckling Load
Third Eigenvalue/
Buckling Load
0.0002 46.049 58.651 100
0.02 4,605 5,865
4.6049 5.8652 10.788 1,000
4,605 5,865 10,788
0.4605 0.5865 1.0788 10,000
4,605 5,865 10,788
Table 8.4 Eigenvalues and buckling loads vs. level of load applied to the model
As mentioned for the previous laminates, the level of the load applied to the model for
the linearized analysis has no influence in the calculated critical buckling loads. As the applied
102
load gets closer to the buckling load, some spurious solutions present at lower levels disappear.
Figure 8.14 First mode, buckling load lbsP 605,4= . Out of plane displacement
Figure 8.15 Second mode, buckling load lbsP 865,5= . Out of plane displacement
103
Figure 8.16 Third mode, buckling load lbsP 788,10= . Out of plane displacement
Only the first three buckling modes were requested in the linearized analyses. All of the
general comments for describing the mode shapes of the previous panels are also applicable for
the 90 degree panel. The 90 degree lay-up produces a rotation in the orientation of the buckling
“bubbles” of the mode shapes. In this panel all of the relative stiffness is now oriented
perpendicular to the direction of the load. It also can be concluded that the 90 degree laminate
divided the buckling load by four with respect to the 0 degree laminate.
8.2.5 Linearized buckling analysis. Summary of results.
Table 8.5 summarizes the results of the linear buckling analysis, high lighting the first
buckling load, which is the one that is critical for design.
104
First Mode Second Mode Third Mode Laminate (degrees with the direction of the load)
lbs kN lbs kN lbs kN
0 degree 21,838 97.135 22,525 100.191 47,456 211.084
20-degree 15,681 69.749 16,335 72.658 34,489 153.407
45-degree 9,498 42.247 10,147 45.134 18,083 80.433
90-degree 4,605 20.483 5,865 26.087 10,788 47.985
Table 8.5 First three buckling loads for each laminate
The trend in the first column indicates that the variation of the angle of the laminate,
particularly of the carbon fibers, with the direction of the load dramatically decreases the critical
buckling load.
For this structure, it is recommended that the linearized analysis be performed with an
applied load close in value to the smallest buckling load. This will prevent the output of spurious
solutions in the analysis. Since the value of the buckling load is unknown in advance, a first
exploratory analysis should be ran to search for meaningful values of the lowest buckling load.
Table 8.5 reveals that the first and second buckling loads are very close in value. Thus, it
cannot be assumed in advance that the configuration adopted immediately after buckling by the
actual tested structure will resemble the first linearized buckling mode. Small variations in the
initial geometric imperfection can trigger the onset of either the first or the second mode.
105
Laminate 0 deg Laminate 20 deg
Laminate 45 deg Laminate 90 deg
Figure 8.17 Rotation of the buckling nodal line. Second mode
106
Laminate 0 deg Laminate 20 deg
Laminate 45 deg Laminate 90 deg
Figure 8.18 Rotation of the buckling nodal lines. First mode
107
CHAPTER NINE
9NONLINEAR BUCKLING AND POSTBUCKLING (WITHOUT FAILURE)
This section describes the development, solution, and results of the nonlinear finite
element modeling for the panels and experiments described in Chapter 5. The correlation of the
model results with the test results is also presented. No failure detection or damage evolution was
included in these models. The focus was solely to evaluate the capabilities of the nonlinear
model to predict the response of the structure in the postbuckling regime. A different model and
analysis that includes failure prediction and damage evolution are presented in Chapter 10. Two
nonlinear models were constructed: one using ANSYS (version 10, release 2006) and a second
one using ABAQUS (version 6.6 release 2007), and results from both models are presented and
compared herein.
9.1 Formulation
9.1.1 Historical approaches
The nonlinear partial differential equations governing composite laminates of arbitrary
geometries and boundary conditions (BC) cannot be solved exactly. Approximate analytical
solutions to the large deflection theory in von Kármán’s sense have been developed in the past
for laminated composite plates. These solutions are limited to rectangular or cylindrical
geometries and in most cases ignore the effects of shear deformation [22]. The Rayleigh-Ritz
method, Galerkin method, perturbation method, and double series method are limited to simple
geometries and BC. The use of approximate numerical methods facilitates the solution of these
equations for general geometries and BC. Among the numerical methods available for the
solution of nonlinear differential equations defined over arbitrary domains, the finite element
108
method is the most practical and robust computational technique [22].
Historically, two distinct approaches have been followed in developing nonlinear finite
element models of laminated structures. The first approach is based on the laminate theory, in
which the 3-D elasticity equations are reduced to 2-D equations through certain kinematic
assumptions and homogenization through the thickness. In the nonlinear formulation based on
small strains and moderate rotations, the geometry of the structure is supposed to remain
unchanged during the loading, and the geometric nonlinearity in the form of von Kármán’s
strains is included. The elements based on such assumptions are commonly referred to as
“laminated elements”.
The second approach is based on the 3-D continuum formulation, where any kinematic
assumptions are directly introduced through the spatial finite element approximation. Nonlinear
strains are included and the equations are derived in an incremental form. This formulation
accounts for geometric changes that occurred during the previous increment of loading and the
geometry is updated between load increments. Finite elements based on this formulation are
called “continuum elements”.
There are two incremental continuum formulations that are used to determine the
deformation and stress states in continuum problems [22]: first, the total Lagrangian formulation,
and second, the updated Lagrangian formulation. In these formulations, the geometry of the
structure for the current load increment is determined from a previously known configuration. In
the total Lagrangian formulation, all of the quantities are referred to a fixed (often the
undeformed) configuration and changes in the displacement and stresses fields are determined
with respect to the reference configuration. The strain and stress measures used in this approach
109
are the Green-Lagrange strain tensor and the 2nd Piola-Kirchhoff stress tensor.
In the updated Lagrangian formulation, the geometry of the structure from the previous
increment is updated using the deformation computed in the current increment, and the updated
configuration is used as the reference configuration for the next increment. The stresses and
strain measures used in this approach are the Cauchy stresses and Almansi infinitesimal strains.
9.1.2 Time approximation and Newton-Raphson method
The principal of virtual work is applied by means of the weak form of the equations of
motion for a composite plate with the first order shear deformation theory. These expressions are
not shown herein and are available in the literature [22]. They contain the first derivatives of the
dependent variables (displacements of the middle plane of the laminate and rotations about x and
y). Therefore, the dependent variables can be approximated by Lagrange interpolation functions.
Substituting those functions into the virtual work statement, the finite element equations of
motion can be obtained, which in compact form are given as:
[ ]{ } { }eee FK =Δ (9.1)
The discretized equations, for an instant of time 1+= Stt are
{ }( )[ ]{ } { } 1,11 +++ =ΔΔ SSSS FK (9.2)
Equation (9.2) represents a system of nonlinear algebraic equations that must be solved
by an iterative method. The method that has proven best for this class of problems is Newton-
Raphson, which is based on Taylor’s series [8]. The Newton-Raphson method considers the
Taylor’s series expansion of equation (9.2) about the known solution, { }SΔ . Suppose that
equation (9.2) is to be solved for the generalized displacement vector { } 1+Δ S at time 1+St . Since
110
the coefficient matrix { }( )[ ]1+Δ SK depends on the unknown solution, the equations are solved
iteratively. To formulate the equations to be solved at the 1+r st iteration by the Newton-
Raphson method, it is assumed that the solution at the r th iteration { }rS 1+Δ is known. Then
define
{ } { }( ) { }( )[ ]{ } { } 01,111 =−ΔΔ=Δ ++++ SSSSS FKR (9.3)
where { }R is called the residual, which is a nonlinear function of the unknown solution { } 1+Δ S .
Expanding { }R in a Taylor’s series about { }rS 1+Δ results in
{ } { }( ) { }( )[ ]{ } { }{ } { } { }( )+Δ−Δ⎥
⎦
⎤⎢⎣
⎡Δ∂
∂+Δ=Δ= +
++
++++
rS
rS
r
S
rSSS
RRKR 111
11110
{ }{ } { } { } { }( ) K+Δ−Δ⎥
⎦
⎤⎢⎣
⎡Δ∂Δ∂
∂+ +
++
+
2
111
1
2
!21 r
SrS
r
S
R
{ } { }( )[ ]{ } { }( ) 00 211 =Δ+ΔΔ+= ++ δδ OKR r
STr
S (9.4)
where ( ).O denotes higher order terms in { }Δδ and [ ]TK is known as the tangent stiffness
matrix (or geometric stiffness matrix):
{ }( )[ ] { }{ }
r
S
rS
T RK1
1+
+ ⎥⎦
⎤⎢⎣
⎡Δ∂
∂≡Δ
{ } { }( )[ ]{ } { } 1,111 ++++ −ΔΔ= SSrS
rS
rS FKR (9.5)
Equation (9.5) can be applied to a typical element. In other words, the coefficient matrix
{ }( )[ ]rSK 1+Δ can be assembled after the element tangent stiffness matrices and force residual
111
vectors are computed. The assembled equations are then solved for the incremental displacement
vector after imposing the boundary and initial conditions of the problem,
{ } { }( )[ ] { }rS
rS
T RK 1
1
1 +
−
+ −Δ−=Δδ (9.6)
The total displacement vector is obtained from
{ } { } { }Δ+Δ=Δ +++ δr
SrS 1
11 (9.7)
The element tangent stiffness matrix is evaluated using the latest known solution, while
the residual vector contains contributions from the latest known solution in computing element
matrix { }( )[ ]{ }rS
rSK 11 ++ ΔΔ and from the previous time step solution in computing element vector
{ } 1, +SSF . After assembly and imposition of the boundary conditions, the linearized system of
equations is solved for { }Δδ .
At the beginning of the iteration (i.e. 0=r ) it is assumed that { } 00 =Δ so that the
solution at the first iteration is the linear solution, because the nonlinear stiffness matrix reduces
to the linear one. The iteration process is continued until the difference between { }rS 1+Δ and
{ } 11
++Δ r
S reduces to a pre-selected error tolerance. The error criterion is of the form (the subscript
1+S in the quantities has been omitted):
ε<ΔΔ−Δ ∑∑=
+
=
+N
I
rI
N
I
rI
rI
1
21
1
21 (9.8)
In equation (9.8) N is the total number of nodal generalized displacements in the finite
element mesh, and ε is the error tolerance. The Newton-Raphson method fails to predict the
nonlinear equilibrium path through the limit points where the tangent matrix [ ]TK becomes
112
singular and the iteration process diverges. Riks suggested a procedure to predict the nonlinear
equilibrium path through limit points. Such a procedure provides the Newton-Raphson method
with a technique to control progress along the equilibrium path.
9.2 Effect of initial imperfections in the nonlinear solution
9.2.1 Effects of initial imperfections in the ANSYS model
As previously stated, the presence of initial geometric imperfections or load eccentricities can
greatly affect the response of the actual structure. The linear mode shapes represent alternative
possible configurations of equilibrium beyond the bifurcation point. Thus, it is realistic to
assume that the state of displacements that the structure will tend to adopt after buckling will
either resemble one of the linear mode shapes or a combination of the linear mode shapes.
Therefore, the mode shapes associated with the lowest buckling loads were used to define an
initial geometric imperfection. Since the linear mode shapes only describe aspect ratios but not
absolute displacements, the mode shapes have to be scaled to represent true imperfections. A
scaling factor was used to provide a maximum displacement of 1% to 5% of the laminate
thickness for any point of the structure.
ANSYS provides two ways of introducing initial imperfections: (1) to read-in a file with
prescribed initial displacements on the nodes of the model based on the mode shapes obtained
from the linear analysis and (2) to initially apply an out of plane perturbation force (or system of
forces) that slightly deforms the structure into a shape that resembles the desired mode shape.
The latter is the procedure followed herein for the ANSYS solution. To find the appropriate
magnitude of the perturbation force, a set of preliminary linear static analyses was completed
using the perturbation force as the only applied force, in order to tune its value to produce a
113
maximum displacement of 5% of the thickness of the laminate. The results are shown in Tables
9.1 and 9.2. Figures 9.1 and 9.2 show the modal shapes obtained using this method. Due to the
proximity of the first two buckling modes, there is a possibility of the structure transitioning
quickly into the second mode. Both initial imperfections (first and second mode) were introduced
separately into the nonlinear analysis for all of the laminates to explore possible differences; it
made no difference with regards to the occurrence of buckling and the developed postbuckling
configuration. Figure 9.3 shows the perturbation forces to induce the second mode.
Thickness: ( )int 124.0= , 5% of thickness: ( )inu 0062.0max =
Perturbation Force (lbs) Maximum displacement (in)
2.0 0.002587
4.0 0.005175
5.0 0.006469
Table 9.1 Estimation of the perturbation force. First mode. Laminate 0 degree.
Figure 9.1 Replication of the first mode with an out of plane perturbation force in the middle
node. Out of plane displacement plot. Laminate 0 degree.
114
Thickness of the laminate: ( )int 124.0= 5% of thickness ( )inu 0062.0max =
Perturbation Force (lbs) Maximum displacement (in)
5.0 0.002939
10.0 0.005877
11.0 0.006465
Table 9.2 Perturbation force estimation. Second Mode. Laminate 0 degree.
Figure 9.2 Replication of the second mode with a couple of perturbation forces, opposite in sign
on symmetric locations. Out of plane displacement plot. Lam 0 deg
The introduction of initial imperfections proved to be a main consideration in order to
achieve convergence for the nonlinear analysis. However, as shown in the results of Table 9.3,
once convergence is achieved the value of the perturbation force was found to have no influence
on the overall results of the analysis.
115
Figure 9.3 Perturbation with a couple of forces to induce the second mode
The findings of this research indicated that if difficulties are found with the convergence
of the non-linear solution then a preliminary exploration should be performed to identify values
of the perturbation force that produce a converged solution..
Perturbation Force (lbs)
Convergence Maximum displacement (lbs)
0.0 NO -----
1.0 NO -----
3.0 NO -----
5.0 YES 0.42366
10.0 YES 0.42505
15.0 YES 0.43360
Table 9.3 Effect of initial imperfections on overall results (laminate 0 deg)
116
It is also important to mention that the ANSYS nonlinear solution can be carried out with
a single load step with automatic sub-stepping, or with multiple load step files, where each file is
executed with automatic sub-stepping. The multiple file option was the one preferred in this
dissertation since it provided a better definition of the response. The introduction of the initial
perturbation force in the multiple file method should be implemented by applying the force in the
first step file and withdrawing it from the subsequent files.
9.2.2 Effects of initial imperfections in the ABAQUS model
For the ABAQUS model, the initial imperfections were introduced by importing a field
of nodal displacements corresponding to the first two mode shapes obtained from the linear
buckling solution. None of the ABAQUS nonlinear models showed convergence difficulties with
any of the imperfection levels introduced, a robust behavior that differed greatly form that
exhibited by the ANSYS solution. Figure 9.4 shows the effect of the magnitude of the initial
imperfection on the response of the ABAQUS nonlinear model.
The results shown in Figure 9.4 reveal that smaller imperfections were associated with
higher buckling loads with no substantial differences in the overall shape of the curve. The
curves plotted in Figure 9.4 are the strains in the compressed diagonal, measured on the outer
surface plies of the same finite element, located close to the center of the laminate. The
magnitude of the initial imperfection also affected the initial separation of the two curves in the
linear regime.
The magnitude of the imperfection was tuned by trial and error to achieve the best
correlation with the test results. As an initial value for this process, the initial imperfection value
117
provided by the intercept of the Spencer Walker plot was utilized. Table 9.4 shows the final
value of imperfection adopted to generate the results presented in the following paragraphs.
0
20
40
60
80
100
120
140
-12500 -10500 -8500 -6500 -4500 -2500 -500 1500εxx strain (microstrains)
Act
uato
r loa
d (k
N)
p1_2_microstrain front facep2_2_microstrain back faceABAQUS imperfection = 0.0025 (in) front faceABAQUS imperfection = 0.0025 (in) back faceABAQUS imperfection = 0.0020 (in) front faceABAQUS imperfection = 0.0020 (in) back faceABAQUS imperfection = 0.0030 (in) front faceABAQUS imperfection = 0.0030 (in) back face
Figure 9.4 Lam 20 deg ABAQUS strains in the first Gaussian integration point in front and back
layers of the laminate FE at the center of the panel
Laminate Spencer-Walker estimated (in)
Best correlation ABAQUS-Test (in)
20 degree -0.0147 -0.0030
45 degree 0.0001 0.0350
90 degree 0.7280 0.0065
0 degree 0.0019 0.0065
Table 9.4 Initial imperfections: estimated vs. adopted for FE correlation
118
9.3 Effect of the sub-stepping in the solution
In the case of the ANSYS nonlinear model, the multiple load step file solution provided
more output points and therefore, better definition of the response in the areas of the nonlinear
curve where the variables change more rapidly. The linear eigenvalue analysis revealed that the
first two modes are very close for the panels under study. It was observed that in the ANSYS
model, limitations in the maximum number of sub-steps, which is an adjustable parameter in the
inputs, could arbitrarily trigger a dominance of either the first or second mode. This type of
variation was never found in the ABAQUS models. Therefore, a previous exploration of ANSYS
solution for different values of this parameter was performed to assure the independence of the
results from the sub-stepping. In general, not limiting the number of sub-steps is recommended.
In the case of the ABAQUS nonlinear model, a robust algorithm automatically chooses the
number of sub-steps and no sensitivity to sub-stepping was noted in the solution.
9.4 Correlation of FE model strains with strain gage readings
The plots presented in this section compare the principal strains provided by the FE
models with the strain gage data of the four test panels. The correlation was investigated at the
central region of the panel where the strain gage rosettes were located back to back on the outer
surfaces of each panel. The location of the rosettes is described in Chapter 5. The normal arms of
the rosettes were oriented in the direction of the load and normal to it. The test principal strains
were calculated from the readings of the three arms of each rosette. The lay-up sequences of the
four test panels are described in Chapter 8.
The footprint of the strain gage arms stretched over an inch from the center of the panel.
Thus, the readings represent the integration or average of the strains at the underlying surface,
119
which were provided by the finely discretized ARAMIS readings. The strains in the direction of
the tension and compression diagonals were extracted from the FE model at the central region of
the panel. In the ANSYS model, the principal strains at the center node of the panel were
requested, and were calculated by the solver as an average of the strains in the four elements
sharing the central node. In the ABAQUS model however, the strains were obtained at the first
Gaussian integration point of the top and bottom plies, of the most representative element located
under the footprint of the strain gage. Figure 9.5 shows in blue the elements located under the
strain gage.
As an operational note, Table 9.5 shows the loading schedule for the solution in ANSYS
and the settings used (multiple load step files which have to be produced first using the command
“Write Load Step File”). The Load Step File contains the perturbation force and applied loads
with constraint and application points and that information does not need to be included in the
general model file. The ABAQUS analysis automates all of the load stepping and none of the file
write operations described for ANSYS are needed.
Table 9.6 shows the values of the buckling load for the different panels obtained from the
different methods used in this dissertation. Every value originated from a totally different source
and it can be observed that the results are in very good agreement.
120
Figure 9.5 Elements under the footprint of the strain gage. ABAQUS model mesh element size
0.25 in, compressed diagonal front face
Figure 9.6 Integration points in ABAQUS S4 element, 3 per layer (nonlinear finite strain
laminated shell)
121
Laminate Load Step No.
Perturbation Force (lbs)
Load at End of Load Step (lbs)
No. of Sub Steps
Max No. of Sub Steps
1 5.00 6,000 10 20
G 2 0.00 12,000 10 20
(20 deg) 3 0.00 14,000 10 20
4 0.00 15,000 10 20
5 0.00 16,000 10 20
6 0.00 18,000 10 20
7 0.00 20,000 10 20
8 0.00 25,000 10 20
1 2.00 3,000 50 100
H 2 0.00 4,000 50 100
(45 deg) 3 0.00 6,000 50 100
4 0.00 10,000 50 100
5 0.00 16,000 50 100
6 0.00 18,000 50 100
7 0.00 25,000 50 100
1 2.00 3,000 50 100
E 2 0.00 6,000 50 100
(90 deg) 3 0.00 10,000 50 100
4 0.00 14,000 50 100
5 0.00 17,000 50 100
6 0.00 20,000 50 100
1 10.00 5,000 50 100
F 2 0.00 8,000 50 100
(0 deg) 3 0.00 12,000 50 100
4 0.00 16,000 50 100
5 0.00 18,000 50 100
6 0.00 20,000 50 100
7 0.00 25,000 50 100
Table 9.5 Loading schedules in the ANSYS model
122
Laminate Analysis Buckling Load (kN)
Buckling Load (lbs)
Runtime (min)
G Linear Eigenvalue Analysis 72.66 16,336 0.01
(20 deg) Nonlinear Analysis ANSYS 63.10 14,186 25.55
Nonlinear Analysis ABAQUS 68.40 15,338 10.55
Experimental (Spencer-Walker plot) 72.80 16,367 Not applicable
H Linear Eigenvalue Analysis 45.13 10,146 0.01
(45 deg) Nonlinear Analysis ANSYS 40.50 9,105 35.50
Nonlinear Analysis ABAQUS 35.50 7,981 12.00
Experimental (Spencer-Walker plot) 43.91 9,871 Not applicable
E Linear Eigenvalue Analysis 20.48 4,604 0.01
(90 deg) Nonlinear Analysis ANSYS 18.00 4,047 20.50
Nonlinear Analysis ABAQUS 19.00 4,272 15.50
Experimental (Spencer-Walker plot) 19.54 4,394 Not applicable
F Linear Eigenvalue Analysis 97.14 21,839 0.01
(0 deg) Nonlinear Analysis ANSYS 65.00 14,613 20.00
Nonlinear Analysis ABAQUS 67.50 15,175 10.00
Experimental (Spencer-Walker plot) 69.38 15,598 Not applicable
Note: running times could be at times an arbitrary measure, since FE software licensed to a
network computer is affected not only by machine capacity but also network traffic.
Table 9.6 Buckling load. Comparison of results
123
9.4.1 Laminate G – 20 degree with the direction of the load
Figures 9.7 and 9.8 show the correlation of the ANSYS non-dimensional principal strains
on the front face with the test data (both tension and compression diagonals) as a function of the
non-dimensional load. Both plots show good correlation with the test results.
Figure 9.7 shows good agreement over the entire linear segment, which represents the in-
plane behavior, and also throughout the change in slope, which indicates the occurrence of
buckling at a load level of 14,186 lbs. The model displayed a higher stiffness than the test article
in the postbuckling regime. Figure 9.8 corresponds to the strain measured in the direction of the
load with good correlation over the whole range of data, but this figure does not clearly reveal
the occurrence of buckling.
Figure 9.9 corresponds to the ABAQUS normalized principal strains versus non-
dimensional load on the compressed diagonal, measured on both sides of the center of the panel,
back to back. The strains on the back face show good correlation even for the postbuckling
regime. This plot represents the transition from compression to tension, and the strain reaches the
positive domain with some minor disparity between analysis and strain gage results after the
buckling event. In general, the ABAQUS model more accurately simulated the response,
including the postbuckling range.
124
0.00
0.50
1.00
1.50
2.00
2.50
3.00
-4.00 -3.50 -3.00 -2.50 -2.00 -1.50 -1.00 -0.50 0.00
Epsilon/Epsilon_cr
P/Pc
rit
Laminate 20 deg - TestLaminate 20 deg - ANSYS
Figure 9.7 Lam 20 deg ANSYS results. Normalized strains on compressed diagonal.
0
0.5
1
1.5
2
2.5
0.00 0.50 1.00 1.50 2.00 2.50 3.00
Epsilon/Epsilon_crit
P/Pc
rit
Laminate 20 deg - TestLaminate 20 deg - ANSYS
Figure 9.8 Laminate 20 deg ANSYS results. Normalized strains on tension diagonal.
125
0.00
0.50
1.00
1.50
2.00
2.50
-5.50 -4.50 -3.50 -2.50 -1.50 -0.50 0.50
Non dimensional strain εxx/εcrit
Non
dim
ensio
nal a
ctua
tor l
oad
P/Pc
rit
Principal Compression Strain, Front Face
Principal Compression Strain, Back Face
ABAQUS (Imp = 0.003) Back Face Compressed Diagonal
ABAQUS (Imp = 0.003) Front Face Compressed Diagonal
Figure 9.9 Laminate 20 deg, ABAQUS results. Normalized strains on compressed diagonal, on
front and back faces.
Figure 9.10 shows the out of plane displacements measured on the front face of the
laminate at the end of the final load step. The correlation is good although both the ANSYS and
ABAQUS models show a mild out of plane displacement towards the corners of the laminate
that is not present in the ARAMIS plot. Both models correlated well in displacements, and for
the 20 degree laminate the rotation of the buckling nodal line is noticeable.
126
Figure 9.10 Lam. 20 deg. Out of plane displacements on front face. Top to down: ARAMIS
surface readings, ANSYS results, ABAQUS results (5 mm = 0.1969 in)
127
9.4.2 Laminate H – 45 degree with the direction of the load
In this case, the ANSYS model provided worse correlation with the test results than the
previous laminate, except over the linear regime as shown in Figures 9.11 and 9.12. The ANSYS
model displayed a higher stiffness in the postbuckling regime than the test article. Figure 9.13
shows the ABAQUS strain correlation, which in general is closer to the test than the ANSYS
solution. The ABAQUS model also showed a stiffer response that the actual panel. This model
exhibited higher sensitivity to the magnitude of the initial imperfection than the 20 degree
laminate.
Figure 9.14 shows the out of plane displacements for the front face of the laminate for all:
test panels, ANSYS and ABAQUS. The correlation is very good and the nodal line rotation is
easily observable.
0.00
1.00
2.00
3.00
-6.00 -5.00 -4.00 -3.00 -2.00 -1.00 0.00
ε/εcrit
P/Pc
rit
Laminate 45 deg ExperimentalLaminate 45 deg ANSYS
Figure 9.11 Lam 20 deg ANSYS. Normalized strains on compressed diagonal.
128
0.00
1.00
2.00
3.00
0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00
ε/εcrit
P/Pc
rit
Laminate 45 deg ExperimentalLaminate 45 deg ANSYS
Figure 9.12 Lam 45 deg ANSYS. Normalized strains on tension diagonal.
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
-8.0 -7.0 -6.0 -5.0 -4.0 -3.0 -2.0 -1.0 0.0 1.0 2.0
Non-dimensional Exx strain (microstrains)
Non
-dim
ensio
nal a
ctua
tor l
oad
(kN
)
Principal compression strain, front facePrincipal compression strain, back faceABAQUS (Imp=0.035) front face compressed digonal ABAQUS (Imp=0.035) back face compressed digonal
Figure 9.13 Lam 45 deg, ABAQUS. Normalized strains critxx εε / on compressed diagonal on
front and back faces.
129
Figure 9.14 Lam. 45 deg. Out of plane displ. on front face. Top to bottom: ARAMIS surface
readings, ANSYS and ABAQUS results (7 mm = 0.2756 in)
130
9.4.3 Laminate E – 90 degree with the direction of the load
The ANSYS model in this case provided good correlation with the test results over the
postbuckling regime as shown in Figures 9.15 and 9.16, but large discrepancies occur around the
buckling event and the linear region.
Figure 9.17 shows the ABAQUS strain correlation, which in general is closer to the test
in the linear range. The ABAQUS model also shows a stiffer response than the actual panel.
Figure 9.18 shows a comparison of the out of plane displacements for the front face, where a
large semi-wave dominates the postbuckling configuration of the laminate.
0.00
0.50
1.00
1.50
2.00
2.50
3.00
-8.00 -7.00 -6.00 -5.00 -4.00 -3.00 -2.00 -1.00 0.00 1.00ε/εcrit
P/Pc
rit
Laminate 90 deg - Experimental
Laminate 90 deg - ANSYS
Figure 9.15 Lam 90 deg ANSYS. Normalized strains on compressed diagonal.
131
0.00
0.50
1.00
1.50
2.00
2.50
3.00
3.50
0.00 1.00 2.00 3.00 4.00 5.00 6.00
P/P
crit
Laminate 90 deg - ExperimentalLaminate 90 deg - ANSYS
ε/εcrit
Figure 9.16 Lam 90 deg ANSYS. Normalized strains on tension diagonal.
0.00
1.00
2.00
3.00
4.00
-8.00 -6.00 -4.00 -2.00 0.00 2.00 4.00
Normalized strain εxx/εcrit
Nor
mali
zed
actu
ator
load
P/P
crit
p2_2/epsilon_crit (Back Face)ABAQUS EEP1 Elem 1628 (imp = 0.0065) Front FaceABAQUS EEP1 Elem 1628 (imp = 0.0065) Back Facep1_2/epsilon_crit (front Face0
Figure 9.17 Lam 90 deg, ABAQUS. Normalized strains on compressed diagonal, on front and
back faces.
132
Figure 9.18 Laminate 90 degree. Out of plane displacement. Top to bottom: ARAMIS surface
readings, ANSYS results, ABAQUS results (12 mm = 0.4724 in)
133
9.4.4 Laminate F – 0 degree with the direction of the load
The ANSYS model provided good correlation with the test results over the tension
diagonal and worse correlation for the compression diagonal except for the linear regime as
shown in Figures 9.19 and 9.20. Figure 9.20 shows overall higher stiffness in the FEM model
with respect to the test panel in the post buckling regime. The reason for the disparity of the
ANSYS model is explained in the paragraph below Figure 9.22.
Figure 9.21 shows the ABAQUS strain correlation, which in general is closer to the test
than ANSYS. The ABAQUS model also exhibited a stiffer response than the actual test panel.
Figure 9.22 shows the out of plane displacement comparison for the front face of the laminate.
No ARAMIS snapshot was recorded during the test, and therefore was not available.
0.00
0.50
1.00
1.50
2.00
2.50
3.00
0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00Normalized strains (ε/εcr)
Non
dim
ensio
nal f
orce
at l
oad
cell
(P/P
cr)
Laminate 0 deg - Experiment
Laminte 0 deg - ANSYS
Figure 9.19 Lam 0 deg ANSYS. Normalized strains on compressed diagonal.
134
0.00
0.50
1.00
1.50
2.00
2.50
3.00
3.50
-8.00 -7.00 -6.00 -5.00 -4.00 -3.00 -2.00 -1.00 0.00Normalized strain (ε/ε crit)
Non
dim
ensio
nal f
orce
at l
oad
cell
(P/P
cr)
Laminate 0 deg - ExperimentLaminte 0 deg - ANSYS
Figure 9.20 Lam 0 deg ANSYS. Normalized strains on tension diagonal.
-0.50
0.00
0.50
1.00
1.50
2.00
2.50
3.00
-7.00 -6.00 -5.00 -4.00 -3.00 -2.00 -1.00 0.00 1.00 2.00
Normalized strain (ε/εcr)
Non
dim
ensio
nal a
ctua
tor l
oad
(P/P
crit)
p1_2/epsilon_crit (front Face0p2_2/epsilon_crit (Back Face)ABAQUS EEP1 Elem 1628 (imp = 0.0065) Front FaceABAQUS EEP1 Elem 1628 (imp = 0.0065) Back Face
Figure 9.21 Laminate 0 deg, ABAQUS. Normalized strains on compressed diagonal, on front
and back faces.
135
Figure 9.22 Laminate 0 degree. Out of plane displacement. (a) Nonlinear Analysis ANSYS last
load step. (b) Nonlinear Analysis ABAQUS last load step
136
Figure 9.22 shows a discrepancy between the mode shape developed in the ANSYS
model and the ABAQUS model at the end of the postbuckling regime. The shape exhibited by
ANSYS corresponds to the first buckling mode, whereas the ABAQUS model developed the
second mode. The most likely cause for this disparity is the proximity between the first and
second linear buckling modes (see Chapter 8 linearized analysis results:
( )lbsModeFirst 838,21= , ( )lbsModeSecond 522,22= ). In the case of a structure with
proximity between the first two critical load levels, it can buckle with deflections arbitrarily
following either mode depending on small eccentricities or load fixture bending effects.
An ARAMIS picture of the deformed surface was not recorded during the test for this
panel. However, the better correlation displayed in Figure 9.21 by the ABAQUS model and the
rest of the ARAMIS data analyzed in Section 5.2.4 suggest that the ABAQUS model described
the buckling more realistically, and therefore the actual test panel most likely developed the
second mode shape.
137
CHAPTER TEN
10PROGRESSIVE FAILURE ANALYSIS
10.1 Failure prediction in the analysis of deeply postbuckled panels
With the incorporation of composite materials into commercial transport airplanes during
the last decade, civil certification requirements have significantly increased. Regarding the static
strength, certification requires showing that the structure does not present any mode of material
damage before reaching design limit load (either matrix or fiber damage, fiber-matrix de-
bonding, or delamination). Beyond limit load, no fiber damage should occur before the ultimate
load (1.5 times design limit load) since the structure has to be able to carry ultimate load for at
least three seconds and the load will be resisted mostly by the fibers. For damage tolerance the
certification requirement is satisfied by loading a deliberately previously damaged structure up to
limit load levels. The components should have undergone barely visible impact damage (BVID)
as well as embedded defects (ED) before static strength testing. The ED are intended to resemble
potential manufacturing defects.
To validate a design for those requirements, an analytical model and/or a test program are
typically carried out to establish a database of allowables. For components that are subjected to
buckling and postbuckling, the simulation requires the incorporation of progressive failure
analysis (PFA). In the same way that a classic thin web aluminum design relies on the elastic
limit of the aluminum to set the maximum level of buckling and diagonal tension allowed in the
structure, PFA is required to find the design point in the postbuckling regime beyond which the
composite shear web should not be loaded. Furthermore, the extension of PFA beyond failure
and its continuation until final collapse reveals areas where damage propagates and shows the
138
important regions of the structure which actually resist the load as the damage progresses. There
are three regions in which stress gradients will potentially initiate damage: on the nodal lines of
the buckling shape, on the crest of the buckling semi-waves, and close to the boundary of the
fixture. Damage over the nodal lines and over the crests of the semi-waves could be sustained by
the laminate for some time, with the continued ability to carry load effectively as long as the
undamaged areas would continue to resist the load working as a tension truss, and the section in
the direction perpendicular to the load can still carry some compression. However, failure over
the boundaries would lead directly to structural collapse, since that damage would detach the
panel from the picture frame and the boundary condition could no longer be imposed, causing
the panel to deform into a collapsed configuration.
As previously mentioned, the buckling and postbuckling FE models with PFA have been
approached incrementally (with increasing levels of complexity) in this dissertation. This
approach is not only advised in the literature [8], it is also required since having a validated
nonlinear model is considered to be a prerequisite to performing PFA. As shown in Table 1.1,
the models in this chapter differ from those in Chapter 9 due to the addition of the PFA.
10.1.1 Material nonlinearities
The response of the undamaged material is assumed to be linear elastic, and the model is
valid with composites for which damage initiates without a large amount of plastic deformation.
Nonlinearities in the material before failure are therefore not considered, but the level of
correlation between the FE model and test data shown in Chapter 9 proves that pre-failure
material nonlinearities can be ignored. The Hashin's initiation criteria are used to predict the
onset of damage, and the damage evolution law used herein is based on the energy dissipated
139
during the damage process and linear material softening. The post- failure effects are included in
an ABAQUS Continuum Damage Mechanics Model (CDM) as explained in the following
section. Nonlinearities that occur just before failure are not characterized in this model.
10.1.2 Delamination growth and decohesion elements
Delamination is a common cause of failure due to an impact, a manufacturing defect, or
stress gradients near geometric discontinuities such as ply drop-offs, stiffener terminations and
flanges, bonded and bolted joints, and access holes. The panels tested and modeled in this
research did not exhibit any of these geometric features that would require modeling for
decohesive interface failure. Also, no internal damage or manufacturing defect was assumed. To
model the growth of such damage, the use of Decohesion Elements [10] is the best technique. It
was never the intent of this research to model delamination; therefore, is not analyzed herein as a
separate class of failure and will not be distinguished from a generic matrix failure.
10.2 Overview of the progressive failure analysis (PFA)
As described in the literature survey of Chapter 3, during the last two decades the
progressive failure analysis of composites has been approached utilizing either the Chang-Chang
or Tsai-Wu failure criteria. Once failure is detected in a ply of an element, the relevant elastic
properties are reduced to zero instantaneously, or over a fixed number of steps. This approach
can be described as the equivalent, at the element level, of the commonly known “ply discount
method” for the classical strength analysis of an entire laminate. These types of models were
referred to in Chapter 3 as IRSP (instantaneous reduction of stiffness properties) and GRSP
(gradual reduction of stiffness properties). Such approaches provide some insight on how the
strength degradation evolves, but are unrealistic since post-failure behavior is disregarded.
140
In order to model damage evolution more realistically, an innovative composite damage
approach [27, 29] was utilized; this approach relies on using a continuum constitutive model
which can feature internal variables that characterize the damage. These types of models are
called Continuum Damage Mechanics (CDM) models [27].
The CDM model used in this dissertation corresponds to the one proposed by
Matzenmiller et al. [29] and it is supported by ABAQUS. The FE implementation of this model
uses a strain softening material law sized by the volumetric energy associated with a failure
mode (area under the stress-stain curve). Since the FE model evaluates the volumetric energy
over an element or group of elements, the results are mesh-sensitive. To alleviate this mesh
dependency, the formulation used herein introduces a characteristic element length into the
material softening law.
In this dissertation, the NL-PFA-Model incorporated Hashin’s failure criteria with a
CDM post-failure constitutive model to simulate the evolution of damage. The parameters
required by the model for this purpose have a clear physical meaning, and can be determined by
standard tests. For this dissertation work, the values used were found in the literature. All PFA
analyses are performed using ABAQUS version 6.6 with the functions *DAMAGE
EVOLUTION, *DAMAGE INITATION, and *DAMAGE STABILIZATION.
10.3 Failure Criteria. Damage activation functions
Damage initiation refers to the onset of degradation at a material point. The damage
initiation criteria used in this dissertation was based on Hashin's theory [6]. These criteria
consider four failure modes for the fiber and matrix constituents. Namely, the different damage
initiation mechanisms considered are: fiber tension, fiber compression, matrix tension, and
141
matrix compression. Denoting by ijσ the components of the local stress tensor in the ply material
axes, the initiation criteria have the general forms shown in Table 10.2. Failure occurs if any of
the indices ije exceed unity.
Failure Mode Range of
Application
Failure Index
Fiber tension ( )011 ≥σ 212
211 ⎟
⎠⎞
⎜⎝⎛+⎟
⎠⎞
⎜⎝⎛= LT
tf SX
eσ
ασ
Fiber compression ( )011 ≤σ 211 ⎟⎠⎞
⎜⎝⎛= C
cf X
e σ
Matrix tension ( )022 ≥σ 212
222 ⎟
⎠⎞
⎜⎝⎛+⎟
⎠⎞
⎜⎝⎛= LT
tm SY
e σσ
Matrix compression ( )022 ≤σ 21222
2222 1
22⎟⎠⎞
⎜⎝⎛+
⎥⎥⎦
⎤
⎢⎢⎣
⎡−⎟⎟
⎠
⎞⎜⎜⎝
⎛+⎟
⎠⎞
⎜⎝⎛= LCT
C
Tcm SYS
YS
eσσσ
Symbol Description
TX Tensile strength in the fiber direction
CX Compressive strength in the fiber direction
TY Tensile strength in the direction perpendicular to the fibers
CY Compressive strength in the direction perpendicular to the fibers
LS Longitudinal shear strength
TS Transverse shear strength
α Coefficient determining the contribution of the shear stress to the fiber tensile initiation criterion
Table 10.2 Hashin’s failure criteria expressions
142
Various failure criteria developed subsequent to the World Wide Failure Exercise
(WWFE) of 1998 [10], incorporate the capability to detect the angle of fracture for the matrix
compression failure. Criteria such as Puck and Schurman [7] and the LaRC series (LaRC04
being the latest [10]) provide such an angle. However, in this dissertation it was considered that
such information did not provide any additional insight or value for the analysis of composite
panels in post buckling. Hashin’s criteria do not provide any information regarding the angle of
fracture. The adequacy of the PFA approach used herein, CDM with Hashin’s initiation
functions, was assessed in light of the comparison of results with test data and with the nonlinear
model without PFA. Results obtained using the current methodology are presented and discussed
later in this chapter.
As a general observation, all of the failure criteria and degradation models result in an
approximation of the damage progression. The WWFE results do indicate that Puck’s method
produces better results than most, particularly for cases involving combined compression
(perpendicular to the fibers) and shear. However, most plate elements provide a poor estimate of
the interlaminar and intralaminar stresses, which makes the 3D Puck criteria impossible to apply.
The initiation criteria presented above can be specialized to obtain the model proposed in
Hashin and Rotem (1973) by setting 0.0=α and 2CT YS = , or the model proposed in Hashin
(1980) by setting 0.1=α . For the models considered for this dissertation, the Hashin option was
used. Table 10.3 shows the different strength values (obtained from the literature [4]) that were
used in the criteria functions.
143
Symbol Description Unidirectional carbon
tape 15 oz/yrd 2
Biaxial glass fabric 12
oz/yrd 2
TX Tensile strength in the fiber
direction
229,924 16,297
CX Compressive strength in the
fiber direction
136,682 16,297
TY Tensile strength in the
direction perpendicular to the
fibers
4,960 16,297
CY Compressive strength in the
direction perpendicular to the
fibers
14,881 16,297
LS Longitudinal shear strength 10,678 17,780
TS Transverse shear strength 1,000,000 10,000
Table 10.3 – Strength material properties used in Hashin’s functions [4]
144
10.4 Material degradation model in the FE simulation
10.4.1 Damage initiation
Damage initiation refers to the onset of degradation at a material point. In ABAQUS the
damage initiation criteria for composites are based on Hashin’s criteria which were introduced in
the previous section. For every step and sub-step (time increment) of the nonlinear FE solution,
the components 122211 ˆ,ˆ,ˆ σσσ of the effective stress tensorσ̂ at every material point are calculated
and used to re-evaluate the initiation criteria. The effective stress tensor is assumed to be the
stress acting over the area of a section that still remains undamaged, and it is computed from the
relationship:
σσ M=ˆ (10.1)
where σ is the nominal or applied stress over the entire section area, including the damaged and
undamaged portions. The matrix M is the damage operator [21,29]
( )
( )
( )⎥⎥⎥⎥⎥⎥⎥
⎦
⎤
⎢⎢⎢⎢⎢⎢⎢
⎣
⎡
−
−
−
=
s
m
f
d
d
d
M
1100
01
10
001
1
(10.2)
and mf dd , and sd are internal (damage) variables that characterize fiber, matrix, and shear
damage. These damage variables are calculated at each integration point for all plies of each
laminated element and are derived from the damage variables tm
cf
tf ddd ,, and c
md , corresponding
to the four modes discussed in the previous section, according to expressions (10.3).
145
( ) ( ) ( ) ( )cm
tm
cf
tfs
cm
tm
m
cf
tf
f
ddddd
ifd
ifdd
ifd
ifdd
−−−−−=
⎪⎩
⎪⎨⎧
<
≥=
⎪⎩
⎪⎨⎧
<
≥=
11111
0ˆ0ˆ
0ˆ
0ˆ
22
22
11
11
σ
σ
σ
σ
(10.3)
Prior to any damage initiation and evolution, the damage operator M , is equal to the
identity matrix, so σσ =ˆ . Once damage initiation and evolution have occurred for at least one
mode, the damage operator becomes significant in the criteria for damage initiation of other
modes. The effective stressσ̂ , is intended to represent the stress acting over the damaged area
that effectively resists the internal forces.
An output variable is associated with each initiation criterion index (fiber tension, fiber
compression, matrix tension and matrix compression) to indicate whether the criterion has been
met. Each of the failure indices are calculated at the integration point of each ply of each
composite plate element. A value of the index of 1.0 or higher indicates that the initiation
criterion has been met. If a damage initiation model is defined without associating an evolution
law, as was done herein for the third model built, the initiation criteria will affect only the
outputs. Therefore, these criteria can be used to evaluate the propensity of the panels to undergo
damage without modeling the progressive damage process. The NL-FA-Model, discussed in
Chapter 9, was developed in this fashion. The sole purpose of the NL-FA-Model was to compare
Hashin’s criteria with classic one-equation criteria such as Tsai-Wu and Tsai-Hill. The current
model (referred to as NL-PFA-Model) includes both the initiation criteria and the material
degradation algorithm to obtain the full PFA.
10.4.2 Evolution of the damage variables for each mode
146
This section presents details regarding the post-damage constitutive model (see Eqs. 10.2
and 10.3). The current PFA algorithm considers the post-damage behavior as a material
constitutive model with strain softening. Prior to damage initiation the material is linearly elastic
with the stiffness matrix of a plane stress orthotropic material. Thereafter, the response of the
material is computed from the constitutive equations of Matzenmiller et al. [29]:
εσ dC= (10.4)
where ε is the strain and dC is the damaged elasticity matrix, which has the form [21,29]
( ) ( ) ( )( ) ( ) ( )
( ) ⎥⎥⎥⎥
⎦
⎤
⎢⎢⎢⎢
⎣
⎡
−
−−−
−−−
=
GDd
EdEdd
EddEd
DC
s
mmf
mff
d
100
0111
01111
2212
1211
υ
υ
(10.5)
where ( ) ( ) 2112111 υυmf ddD −−−=
The parameter fd reflects the current state of fiber damage, md reflects the current state
of matrix damage, and sd reflects the current state of shear damage. The stiffness 1E is the
Young's modulus in the fiber direction, 2E is the Young's modulus in the matrix direction, G is
the shear modulus, and 12υ and 21υ are Poisson's ratios. The damage variables fd , md , and sd
are derived from damage variables cm
tm
cf
tf dandddd ,, corresponding to the four damage modes
using the expressions (10.3).
In order to simulate the post failure evolution in the most realistic fashion, a linear strain
softening model was used. Some strain softening models that have been proposed in the
literature are compared in Figure 10.1. This family includes linear elastic-perfectly plastic; linear
147
elastic-linear softening; linear elastic-progressive softening; linear elastic-regressive softening,
and Needleman [30]. The main characteristic of all of the softening models is that the material
continues to transfer load after the onset of damage ( 0ε in Figure 10.1). For loading
corresponding to each failure mode (fiber tension and compression, matrix tension and
compression) after the constituents have reached their respective strengths dictated by the
Hashin’s failure functions, the stiffnesses are gradually reduced to zero following the softening
law. The area under the stress-strain curve is the respective fracture energy associated with that
failure mode. The values of CG for the different failure modes can be obtained from simple
experiments or from existing data in the literature.
Figure 10.1 Different strain softening models. The suffix of each intersection with the
horizontal axis labels each curve
To alleviate mesh dependency during the material softening, a characteristic element
length is introduced into the formulation; the resulting strain softening constitutive law is
expressed as a stress-displacement relation. The damage variable will evolve such that the stress-
148
displacement behaves linearly, as shown in Figure 10.2, in each of the four failure modes. The
positive slope of the stress-displacement curve prior to damage initiation corresponds to linear
elastic material; the negative slope after damage initiation is achieved by evolution of the
respective damage variables following the equations of Table 10.4.
Figure 10.2 Bilinear strain softening law in terms of equivalent magnitudes
Equivalent displacement and stress for each of the four damage modes are defined as
149
follows:
Failure Mode Range of
Application
Equivalent displacement and equivalent
stress
Fiber tension ( )0ˆ11 ≥σ ( )212
211 εαεδ += Cft
eq L
Cfteq
fteq Lδ
εταεσσ 12121111 +
=
Fiber compression ( )0ˆ11 <σ 11εδ −= Cfceq L
Cfceq
fceq Lδ
σεσσ 111111 −−−−
=
Matrix tension ( )0ˆ 22 ≥σ ( )212
222 εεδ += Cmt
eq L
Cmteq
mteq Lδ
ετεσσ 12122222 +
=
Matrix compression ( )0ˆ 22 ≤σ ( )212
222 εεδ +−= Cmc
eq L
Cmceq
mceq Lδ
ετεσσ 12122222 +−
=
Table 10.4 Equivalent displacement and equivalent stress for each failure mode
For elements with a plane stress formulation the characteristic length CL is computed as
the square root of the integration point area. The symbol in the equations above represents
the Mc-Cauley bracket operator, which is defined for every ℜ∈x as
( )2
xxx
+= or { }xx ,0max=
After damage initiation (i.e., 0eqeq δδ ≥ ) the damage variable for a particular mode is given
150
by
( )( )0
0
eqf
eqeq
eqeqf
eqdδδδδδδ
−
−= (10.6)
where 0eqδ is the initial equivalent displacement at which the initiation criterion for that mode
was met and feqδ is the displacement at which the material is completely damaged in this failure
mode. The above relation is presented graphically in Figure 10.3.
Figure 10.3 Damage variable as a function of equivalent displacement.
The values of 0eqδ for the various modes depend on the elastic stiffness and the strength
parameters specified as part of the damage initiation definition. Unloading from a partially
damaged state, such as point B in Figure 10.2, occurs along a linear path toward the origin in the
plot of equivalent stress vs. equivalent displacement; this same path is followed back to point B
upon reloading.
151
The energy dissipated due to failure, CG , which corresponds to the area of the triangle
OAC in Figure 10.2, must be specified for each failure mode. The values of feqδ for the various
modes depend on the respective CG values. Since the composite laminates under study are
hybrids of Glass/Epoxy with Carbon/Epoxy, the NL-PFA-Model needs different values of CG
for each material as well as for each failure mode. Table 10.3 shows the different values used,
which were found in the literature [31]. Some of the values for Glass/Epoxy were not found in
the literature, and were estimated from the values known for the carbon/epoxy material system,
in proportion to the relation between the stiffness moduli of the carbon/epoxy system to the
glass/epoxy system.
Energy Released (lbs/in)
G1+
G1-
G2+
G2-
G6
Failure Mode Fiber Fracture Tension
Fiber Fracture Compression
Matrix Fracture Tension
Matrix Fracture
Compression
Shear Fracture
T300/934 512.929 446.922 1.313 4.339 2.626
Glass/Epoxy 743.747 648.0365 1.904 6.292 3.809
Table 10.5 Energy Released constants [31]
10.4.3 Maximum degradation and element removal
ABAQUS provides control on how elements with severe damage are treated. By default,
the upper bound to all damage variables at a material point is 0.1max =d . This upper bound can
be reduced; nevertheless in the NL-PFA-Model the default option was used. By default, an
152
element is removed (deleted) once damage variables for all failure modes at all material points
reach maxd . For a removed element the output variable STATUS is set to zero for the element,
and no resistance occurs due to subsequent deformation. However, the element still remains in
the ABAQUS model and is visible in the post-processing visualization module.
10.4.4 Viscous regularization algorithm
The PFA process of the NL-PFA-Model evaluated the stresses at the end of each load step of the
nonlinear static solution, over each integration point within each ply of each element, and
modified the material properties in the damaged plies. When that loop was completed at the end
of the load step, the stresses were necessarily different due to changes in material properties and
element status, and therefore needed to be redistributed. A new equilibrium nonlinear solution
was obtained right after the PFA algorithm before moving on to the next load step. Material
models exhibiting softening behavior and stiffness degradation often lead to severe convergence
difficulties in implicit FE solutions, such as ABAQUS/Standard used herein. To overcome some
of these convergence difficulties, the viscous regularization scheme, available in
ABAQUS/Standard, was activated. This technique causes the tangent stiffness matrix of the
softening material to be positive for sufficiently small time increments. In this regularization
scheme a viscous damage variable is defined by the evolution equation (10.7):
( )vv ddd −=η1& (10.7)
with ( )vv ddtdd =&
where t represents time, η is the viscosity coefficient representing the relaxation time of the
153
viscous system, and d is the damage variable evaluated in the inviscid model before
regularization. The damaged response of the viscous material is given as:
εσ dC= (10.8)
In expression (10.8) the damaged elasticity matrix, dC , is computed using viscous values
of damage variables for each failure mode. Using viscous regularization with a small value of the
viscosity parameter, small compared to the characteristic time increment, usually helps improve
the rate of convergence of the model in the softening regime, without compromising results. The
basic idea is that the solution of the viscous system relaxes to that of the inviscid case as
∞→ηt , where t represents time.
Different values of viscous coefficients can be specified for the different failure modes
commonly referred to with the notation mcmtfcft ηηηη ,,, for viscosity coefficients for fiber
tension, fiber compression, matrix tension, and matrix compression failure modes respectively.
Alternatively, the algorithm allows for defining just one viscous coefficient to be used for all
failure modes. In the NL-PFA-Model built herein, just one viscous coefficient was defined.
The NL-PFA-Model was solved several times with different values of the viscous
coefficient to explore the effect of the viscous regularization on the overall solution. Figure 10.4
shows the strains calculated at the center of the 20 degree panel, on the front and back faces, for
an initial out of plane displacement imperfection of 0.003 in. at the middle point for different
viscous coefficients. The results of this experiment show that for higher viscosities the solution
resembles that of the nonlinear analysis without progressive failure.
Comparing the PFA solution with the experimental results of the test it can be noted that
154
the PFA solution does a better job at predicting the panel behavior in the linear regime and even
more accurately predicts the occurrence of buckling. However, it exhibits lower stiffness than the
tested panels after the buckling event, thus providing a conservative solution. For values of
viscosity higher than 100, the response of the model remained unchanged and became insensitive
to further increases. For that reason, a value of 100 for the viscous coefficient was finally
adopted.
0
20
40
60
80
100
120
140
-15000 -13000 -11000 -9000 -7000 -5000 -3000 -1000 1000 3000
εxx strain (microstrains)
Act
uat
or lo
ad (
kN)
Strain Gage Front FaceStrain Gage Back FaceNonlinear no PFA (Imp = 0.003) front faceNonlinear no PFA (Imp = 0.003) back faceeta = 0.5 front faceeta = 0.5 back faceeta = 1.5 front faceeta = 1.5 back faceeta = 10.0 front faceeta = 10.0 back faceeta = 100.0 front faceeta = 100.0 back face
Figure 10.4 Effect of the viscous regularization coefficient in the nonlinear solution. Strains
on compressed diagonal at the center, front and back faces (20 degree panel)
155
10.5 Results of the nonlinear model with progressive failure analysis
The PFA scheme was introduced in the nonlinear model through the functions
*DAMAGE EVOLUTION, *DAMAGE INITATION, and *DAMAGE STABILIZATION. At
every integration point (one per ply, see Figure 9.2) the four damage indices defined in Hashin’s
functions are calculated and tracked as a history output. The model provides contour plots for the
four damage indices as shown in Figures 10.5 through 10.24. The output variables represented
are listed in Table 10.6. As mentioned above, only the 20 degree laminate model was expanded
with the PFA capability.
Variable name Definition
HSNFTCRT Hashin’s tensile fiber initiation criteria at integration points
HSNFCCRT Hashin’s compressive fiber initiation criteria at integration points
HSNMTCRT Hashin’s tensile matrix initiation criteria at integration points
HSNMCCRT Hashin’s compressive matrix initiation criteria at integration points
Table 10.6 Output damage indices [21]
The nonlinear analysis with PFA simulated a ramp loading divided into 16 steps to help
convergence and make sure that enough intermediate points were recorded. The loading schedule
is indicated in Table 10.7.
156
Step Incremental Load (lbs) Step Incremental
Load (lbs) Step Incremental Load (lbs) Step
Incremental Load (lbs)
1 1000 5 1000 9 1000 13 1000 2 1000 6 1000 10 1000 14 2000 3 4000 7 1000 11 1000 15 7000 4 1000 8 1000 12 1000 16 3000
Table 10.7 Loading schedule, nonlinear analysis with PFA
10.5.1 Fiber tensile failure evolution
Figure 10.5 shows the first fiber tensile (FT) damage, which took place during step 9,
with the FT index reaching value of 1. An inspection of the failure index over all plies of the
laminate revealed that plies 1 and 8 are the most severely affected by this failure mode.
However, the elements affected were located under the picture frame fixture and do not represent
a relevant failure occurrence conducive to final collapse. The first failure worth consideration is
shown in Figure 10.8, during step 15, with ( )lbsP 04.465,27= . Failure at that load level was
worth considering due to the area of damage located on the right hand side of the lower corner. It
can be observed that the panel’s inability to carry any load in the damaged area generates a shift
in the load path to the right side, which results in further severe damage developing on the right
crest of the mode shape.
157
Figure 10.5 Fiber tensile failure index. First occurrence of damage, load step 9. Actuator
load ( )lbsP 799,13=
Figure 10.6 Fiber tensile failure index, load step 12, ( )lbsP 163,17=
158
Figure 10.7 Fiber tensile failure index, load step 14, ( )lbsP 325,20=
Figure 10.8 Fiber tensile failure index, load step 15, ( )lbsP 465,27=
159
Figure 10.9 Fiber tensile failure index, load step 16, ( )lbsP 434,30=
10.5.2 Fiber compressive failure evolution
Figure 10.10 shows the fiber compressive (FC) damage at the end of load step 14. An
inspection of the index failure over all plies of the laminate revealed that plies 1 and 8 were the
most severely affected by this failure mode. The elements affected were located under the picture
frame fixture, and the failure index was still below one and remained so until load step 16.
Failure was not declared until reaching a load level of ( )lbsP 58.433,30= . It can be inferred
from the plots that FC was not a dominant type of failure and it did not drive the final structural
collapse.
160
Figure 10.10 Fiber compressive failure index, load step 14 ( )lbsP 325,20=
Figure 10.11 Fiber compressive failure index, load step 15, ( )lbsP 465,27=
161
Figure 10.12 Fiber compressive failure index, load step 16, ( )lbsP 433,30=
10.5.3 Matrix tensile failure evolution
Figure 10.13 shows the first matrix tensile (MT) damage, which occurred during step 7.
An inspection of the failure index for all plies of the laminate revealed that plies 1 and 8 were the
most severely affected by this failure mode. However, the elements affected were located under
the picture frame fixture, and did not represent a relevant onset of damage. The first failure worth
consideration is shown in Figure 10.17 during step 15, with a load level of ( )lbsP 04.465,27= .
162
Figure 10.13 Matrix tensile failure. First occurrence of damage, load step 7. Actuator load
( )lbsP 497,11=
Figure 10.14 Matrix tensile failure, load step 12. ( )lbsP 163,17=
163
Figure 10.15 Matrix tensile failure, load step 14. ( )lbsP 325,20=
Figure 10.16 Matrix tensile failure. End of step 15. ( )lbsP 465,27=
164
Figure 10.17 Matrix tensile failure. End of step 16. ( )lbsP 434,30=
10.5.4 Matrix compressive failure evolution
Figure 10.18 shows the first matrix compressive (MC) damage, which occurred during
load step 9. The elements affected were located under the picture frame fixture, and did not
represent relevant damage. The first failure worth consideration is shown in Figure 10.20 at the
end of step 14 with ( )lbsP 60.324,20= . This was the most massive type of failure and the
analysis showed two bands of severe damage, formed in areas of the buckled shape under high
stress gradients. This mode of failure most likely drove the final collapse of the structure. Since
MC failure was driving the collapse of the panel, failure continued to develop ply-by-ply as
shown in Figures 10.23 and 10.24. These reflect the MC failure index at load step 14 at the
middle integration point of each layer. Damage is present to a considerable extent in layer 4,
165
which is near the middle surface of the 8 layer laminate with layers1 and 8 on the front and back
faces respectively.
Figure 10.18 Matrix compressive failure, load step 9 ( )lbsP 799,13=
Figure 10.19 Matrix compressive failure, load step 12 ( )lbsP 163,17=
166
Figure 10.20 Matrix compressive failure, load step 14 ( )lbsP 325,20=
Figure 10.21 Matrix compressive failure, load step 15 ( )lbsP 465,27=
167
Figure 10.22 Matrix compressive failure, load step 16 ( )lbsP 433,30=
Figure 10.23 Matrix compr. failure, load step 14. Failure index at plies 1, 2, 3 & 4
168
Figure 10.24 Matrix compr failure load step 14. Failure index at plies 5, 6, 7 & 8
169
170
10.6 Summary of results. Nonlinear model with progressive failure analysis
As mentioned above, only the model for the 20 degree laminate was solved with the
extended PFA capability. For each failure mode, a threshold load level was found in which
severe onset of damage was detected as shown in Table 10.8. A structural design seeking to
preserve the integrity of the panels can only develop postbuckling stresses at load levels
lower than the lowest of the damage levels found for each failure mode.
Load level at first damage Output Variable Failure mode
lbs kN
HSNFTCRT Fiber tension 465,27 17.122
HSNFCCRT Fiber compression 434,30 37.135
HSNMTCRT Matrix tension 465,27 17.122
HSNMCCRT Matrix compression 325,20 41.90
Table 10.8 Load levels at occurrence of first damage for each failure mode
Figure 10.25 shows the comparison of strains at the middle point of the laminate, on
the compressed diagonal, for readings on the front and back faces. The load levels for the
different types of damage are represented as horizontal lines. It can be concluded that the
damage level that limits the postbuckling load carrying capability is the level corresponding
to matrix compressive failure with the values shown in Table 10.8. Table 10.9 shows the
final summary of buckling loads, and Table 10.10 shows the final design load carrying
capability.
05
101520253035404550556065707580859095
100105110115120125130135140
-13000 -11000 -9000 -7000 -5000 -3000 -1000 1000 3000
εxx strain (microstrains)
Act
uat
or lo
ad (
kN)
Strain Gage Front FaceStrain Gage Back FaceNonlinear no PFA (Imp = 0.003) front faceNonlinear no PFA (Imp = 0.003) back faceNonlinear with PFA (eta = 100.0, imp=0.003) front faceNonlinear with PFA (eta = 100.0, imp=0.003) back faceFiber tension failure levelFiber compression faliure levelMatrix tension failure levelMatrix compression failure level
Figure 10.25 Strain on compression diagonal vs. actuator load with PFA results.
171
172
Analysis Buckling Load (kN) Runtime (min)
Linear Eigenvalue Analysis 72.66 0.01
Nonlinear Analysis ANSYS 63.10 25.55
Nonlinear Analysis ABAQUS 68.40 10.55
Experimental 72.80 Not applicable
Nonlinear Analysis ABAQUS with Progressive Failure
67.50 105.50
Table 10.9 Laminate 20 deg .Summary of buckling loads
Analysis Limiting Load to avoid laminate damage(kN)
Nonlinear Analysis ABAQUS with Progressive Failure
90.41
Table 10.10 Laminate 20 deg . Final design load carrying capability
10.7 Comparison of the Hashin’s failure functions with other failure criteria
In order to compare the Hashin’s functions with the most commonly used one-
equation failure criteria, a separate ABAQUS model was built, the NL-FA-Model, in which
damage evolution is ignored and only the failure criteria are considered. In this model,
several failure criteria were evaluated, at each load level, element, and ply. Within each ply,
the S4 element under a Simpson’s rule formulation uses three integration points (top of layer,
middle plane, and bottom of layer). The failure criteria evaluated are listed in Table 10.11.
173
Failure criterion Mode Based
Hashin Fiber Tension Fiber Compression Matrix Tension Matrix Compression
YES
Tsai Wu NO
Tsai Hill NO
Maximum Stress NO
Maximum Strain NO
Table 10.11 Failure criteria compared in the NL-FA-Model.
The NL-FA-Model was solved only for the 20 degree laminate. First failure was
consistently detected at load step 14 ( ( )lbsP 60.324,20= ) with the NL-PFA-Model. For that
load step ply number 8 located on the front face was the most severely damaged as shown in
Figures 10.26 through 10.28. Any failure evaluation subsequent to load step 14 is not
realistic since this model does not consider damage evolution, but simply the state of stresses
at the load step and the resulting failure index calculated from the stress values. Therefore,
the failure indices can take values larger than one. In all of the contour plots, the value of
unity is displayed in red color to denote failure. Values higher than one are plotted in grey.
Hashin’s criteria proved to be the most conservative, flagging failure before all of the non
mode based criteria, with the matrix compression failure as the most critical.
Figure 10.26 Hashin’s failure indices, load step 14, layer 8 (front face) ( )lbsP 325,20= . Left to right and top to bottom: fiber tension, matrix tension, fiber compression, matrix compression.
174
Figure 10.27 All non mode based failure indices, load step 14, layer 8 (front face) ( )lbsP 325,20= . Left to right and top to bottom: Tsai Wu, Tsai Hill, Maximum Stress, Maximum Strain.
175
Figure 10.28 All plies Tsai Hill failure index, load step 14, layer 8 ( )lbsP 325,20=
176
177
CHAPTER ELEVEN
11CONCLUSIONS AND RECOMENDATIONS
This dissertation presented a new methodology to support the design of composite shear
webs by expanding the working range of the structure well into the postbuckling regime. This
objective was accomplished by using the numerical simulation capabilities of nonlinear finite
element analysis combined with material failure criteria and a damage evolution model. The
method was validated by correlation of strain and displacements results with data from
laboratory experiments carried out on four composite panels built with hybrid carbon-
epoxy/glass-epoxy lay-ups and different orientations.
A literature review revealed the absence of updated progressive failure analyses (PFA)
for the type of structure and loading under consideration (composite hybrid flat panels under in-
plane shear) and also showed how composite failure detection and the simulation of damage
evolution are an active field of research. This review guided the study towards choosing a mode
based failure theory together with a material degradation model formulated using continuum
damage mechanics (CDM).
A review of the solutions provided by classic analytical methods to predict the onset of
instability and the value of the buckling load was also carried out. Important limitations were
found with regards to the practical applicability of classic analytical solutions. For the kind of
structure, loading and boundary conditions of this study, the analytical solutions found were only
applicable for the 45 degree laminate. Furthermore, the case under study herein does not accept
an exact analytical solution but rather an approximation using Raleigh-Ritz technique [22]. There
is a method for obtaining an exact solution but published results are rare. The Rayleigh-Ritz
178
analytical buckling load was somewhat higher than the lowest buckling load found through the
linearized FE analysis and close to the buckling load of the second FE mode. The specially
orthotropic analytical solution should be viewed as a very approximate solution for the lowest
buckling load of the structure.
The aforementioned set of composite laminated panels were tested in a picture frame
shear loading fixture. The test panels differed in the orientation of the laminate with respect to
the direction of the load. Four orientations were considered: 0, 20, 45, and 90 degrees. The test
results were recorded using different means, which include strain gages as well as a photo-
sensitive digital image system (ARAMIS). The strain gage data (due to the size of the gages)
represented more of an average; whereas, the ARAMIS data represents detailed localized strains
(and displacements). The data collected describing the postbuckling response of the test panels
was compared between the different data sources in order to access the consistency of the results.
In general both set of data were found to be in agreement.
Mathematical treatments of the test data, such as the Southwell’s method and its Spencer-
Walker extension to nonlinear plates [25,32], were applied to extract the experimental values of
the critical buckling loads for each specimen. This method proved to be a robust way to extract
the critical buckling loads from the experimental data. Good consistency was found between the
values obtained using Spencer-Walker and other graphical methods to determine the
experimental buckling loads. The recommendation from this research is to rely on the Spencer-
Walker method for the experimental determination of the buckling load.
Regarding the numerical analysis methodology, it was approached with increasing levels
of complexity. First, a linearized eigenvalue solution was obtained (using the ANSYS v.10
179
commercial package) to provide a first approximation of the values of critical buckling loads.
The critical loads obtained with the linearized analysis were compared with the experimental
buckling loads from the Spencer-Walker method, and good correlation was obtained.
Next, nonlinear FE models (without failure) were built for the four different panels, to
fully simulate the postbuckling response and correlate it with the experimental results. Two sets
of models were developed: one set with ABAQUS v.6.6 and one set with ANSYS v.10.
As reported in the literature, the presence of initial imperfections was found to have a
significant impact. Two different methods of including the initial imperfection in the FE model
were explored. Both methods produced the same results. In ANSYS the imperfection was
introduced by means of an out of plane perturbation force. The appropriate magnitude of such
force was calculated from a series of FE static solutions in which the perturbation force was
varied in order to find the value that produced an out of plane displacement at the center of the
specimen ranging between 0% and 5% of the total thickness of the laminate. In ABAQUS, the
imperfection was introduced as an initial displacement field obtained from a linear combination
of the lowest buckling modes from the linearized analysis. Linear combinations of the first two
modes were used, and the effect of introducing additional higher modes in the linear combination
was found to be negligible.
Correlation of experimental and finite element displacements and strains at the center of
the panel were used to judge the accuracy of the models. The FE results exhibited good
correlation with the test results, with the 20 degree laminate model showing the closest
agreement between experimental and FE data. In an attempt to produce better agreement
between the data, a range of initial imperfections were introduced into the FE model. Future
180
research to obtain more refined correlations is recommended, including a physical exploration of
the picture frame fixture to detect particular nuances such as bedding effects or eccentricities that
might provide additional insight. Furthermore, initial imperfections should be measured and
characterized for each test panel.
Both software packages, ANSYS and ABAQUS, provided good results. However, the
robustness in the convergence of the solutions together with superior pre and post processing
capabilities and somewhat better correlations with test made ABAQUS v6.6 the package of
choice for the implementation of the progressive failure analysis (PFA) in the nonlinear model.
This implementation was only carried out for the 20 degree laminate model. To implement the
nonlinear model with PFA capabilities, two different models were created: (1) one with failure
detection capability only, and (2) one with failure detection and a damage evolution algorithm.
The first model (with failure detection capability only) included Hashin’s theory of
failure for reinforced composites. The results obtained based on Hashin’s failure criteria were
compared to classic single-equation criteria for composite structures; namely, comparisons were
made with the maximum stress, maximum strain, Tsai-Hill, and Tsai-Wu criteria. Besides
providing information on failure for different modes, Hashin’s proved to be the most
conservative criteria.
In the second model the damage evolution algorithm was added to the nonlinear model to
complete the progressive failure analysis capability. Different aspects of the model were
discussed such as the constitutive laws used to model material degradation once failure had been
detected. Since such a constitutive model is not activated until failure has been detected at the
element level for at least one mode, the Hashin’s criteria also act as functions for the activation
181
of the material degradation model.
The material degradation model is introduced in the FE solution as a constitutive model,
and it relies on the use of artificial viscous damping in the element’s stiffness properties to
mitigate the convergence difficulties in the nonlinear solution after the introduction of the PFA.
The effect of different levels of damping on the solution was evaluated. A single value of
damping was used for both materials (unidirectional carbon/epoxy and biaxial glass/epoxy) and
also for both fiber and matrix constituents. A recommendation derived from this study is that the
damping level should be chosen such that variations in the damping constant do not greatly
affect the solution. A potential continuation of this research should include the effect of using
different damping constants for each material and each failure mode.
The results of the complete nonlinear analysis with PFA were compared with the
nonlinear solution without failure and with the test results. The model with PFA produced an
improved FE-experimental correlation in the linear range and around the buckling region;
whereas, no improvements were found in the high load level postbuckling region. In that region
the stiffness of the specimen was underestimated by the nonlinear model with PFA, which
resulted in a more conservative approach than the nonlinear only model without PFA.
As a potential continuation of this research, the differences between the nonlinear-PFA
model and the test results can be further reduced by using test values of the critical energy
release constants, which can be obtained by standard fracture toughness tests of the specific
composite material systems used to build the specimens. The values used in this dissertation
were found in the open literature.
The evolution of the four different failure modes was examined in order to visualize the
182
load paths leading to the final collapse of the structure. The most massive mode of failure was
found to be matrix compression, which was fully developed over the structure for a load level in
which the fiber tensile failure had barely started. To further validate the predictions of damage
evolution presented in this dissertation, an ultrasound scanning of the test panels to map the
existence and nature of damage would have been very valuable. This line of work is
recommended as a continuation of this research.
From the perspective of establishing a design methodology, the current nonlinear-PFA
analysis provides enough information to determine postbuckling load levels with no damage
versus those with severe damage. The different levels of load corresponding to the occurrence of
damage, for each of the failure modes tracked, were plotted together with the load-strain
response curves of the 20 degree panel to establish the maximum allowable load at the first
occurrence of failure.
In order to further improve the analysis models and correlation the following
recommendations are made. First, the entire test fixture should be modeled using 3D shell
elements, with the properties of the exact aluminum alloy used to build it, and the *FASTENER
feature available in ABAQUS should be utilized to model the stiffness of the picture frame
fasteners.
Next, it is recommended to carry out test of additional panels. Following the
recommendation of the Federal Aviation Administration (FAA), at least 3 identical specimens of
each panel should be tested This approach provides more consistent test results. It is also
recommended that a large variety of potential initial imperfections be investigated. Different
linear combinations of buckling modes (up to the third buckling mode) should be introduced in
183
the nonlinear model to potentially improve the correlation with test results. Finally, panels with
initial damage should be tested and analyzed to evaluate the effect of various types of damage on
postbuckling strength and stability.
184
REFERENCES
185
12REFERENCES
[1] Wagner, H., "Remarks on Airplane Struts and Girders Under Compressive and Bending Stresses,” NACA TN 500, 1935.
[2] Kuhn, P., “A Summary of Diagonal Tension Part I/II,” NACA Technical Report 2661/2662, 1952.
[3] Niu, C.Y., Composite airframe analysis and design, Hong Kong Mil. Press, 1992.
[4] Hermann, T., Mamarthupatti, M.S., Locke, J., “Postbuckling Analysis of Laminate Composites Utilizing Commercial FEA Software,” AIAA 2005-194.
[5] Wittemberg, T. C., van Batten, T. J., “Parametric Design Curves for Shear Buckling of Flat Orthotropic Stiffened Panels with Application to Glare Material,” AIAA 2004-2054.
[6] Hashin, Z.,“Failure Criteria for Unidirectional Fiber Composites,” Journal of Applied Mechanics, Vol. 47, pp. 329–334, 1980.
[7] Puck, A., Schurman, H., “Failure Analysis of FRP Laminates by Means of Physically Based Phenomenological models,” Composites Science and Technology 58 (1998) 1045-1067, Elsevier Science Limited 1998.
[8] Bathe, K. J., Finite Element Procedures, Prentice Hall 1998.
[9] Ambur, D. R., Jaunky, N., Davila, C. G., “Progressive Failure of Composite Laminates Using LaRC02 Criteria”, Paper AIAA 2004-1595.
[10] Pinho, S. T., Davila, C. G., Camanho, P. P., Iannucci, L., Robinson, P., “Failure Models and Criteria for FRP Under Three Dimensional Stress States Including Shear Non-Linearity.” NASA-TM-2005-213530.
[11] ANSYS 10, Reference Manual, Element Type Reference.
[12] Chang, F. K., and Chang, K. Y., “A Progressive Damage Model for Laminated Composites Containing Stress Concentrations,” Journal of Composite Materials, Vol. 21, September 1987.
[13] Talreja, R., “Modeling of Damage Development in Composites Using Internal Variable Concepts,” Damage Mechanics in Composites, AD Volume 12, 1987.
[14] Chang, F. K., and Lessard, L. B., “Damage Tolerance of Laminated Composites Containing an Open Hole and Subjected to Compressive Loading: Part I-Analysis,” Journal of Composite Materials, Vol. 25-January 1991.
[15] Singh, S. B., and Kumar, A., “Postbuckling Response and Failure of Symmetric
186
Laminates Under In-Plane Shear,” Composites Science and Tech. 58 (1998) 1949-1960.
[16] Huang, D., Minnetyan, L., “Computational Simulation of Progressive Fracture in Stitched J-Somposite Shear Panels in the Postbuckling Range,” AIAA-99-1356.
[17] Davila, C. G., Ambur, D. R., and McGowan, D. M., “Analytical prediction of damage growth in notched composite panels loaded in axial compression,” AIAA-99-1435.
[18] Jaunky, N., Ambur, D. R., Davila, C. G., and Hilburger, M., “Progressive failure studies of composite panels with and without cutouts,” NASA/CR-2001-211223, ICASE Report No. 2001-27.
[19] Ambur, D. R, Jaunky, N., and Hilburger, M., “Progressive failure studies of stiffened panels subjected to shear loading,” NASA/CR-2002-211757, ICASE Report No. 2002-24. [20] Zemcik, R., and Las, V., “Numerical simulation of the progressive damage to FRC panels due to shock loading,” ISSN 1580-2949, MTAEC9, 39(3)77(2005).
[21] ABAQUS User’s Manual Version 6.6, Hibbit, Karlsson, and Sorensen Inc.
[22] Reddy, J. N., Mechanics of laminated composite plates and shells. Theory and analysis, CRC Press LLC, 2004.
[23] Hermann, T. M., Locke, J. E., “Failure analysis of anisotropic composites utilizing commercial FEA software”, AIAA paper AIAA 2005-975.
[24] Southwell, R.V., “Theory of Elasticity”, Oxford University Press, (1941).
[25] Spencer, H. H. and Walker, A. C., “Critique of Southwell Plots with Proposals for Alternative Methods”, Journal of Experimental Mechanics, Vol 15, No.8 August 1975, p 303-310.
[26] Pinho, Iannucci, L., Robinson, P., “Physically based failure models and criteria for laminated fibre-reinforced composites with emphasis on fibre kinking. Part I: FE implementation.” Composites Part A, Vol 37 (2006) p 63-73.
[27] Pinho, Iannucci, L., Robinson, P., “Physically based failure models and criteria for laminated fibre-reinforced composites with emphasis on fibre kinking. Part II: FE implementation.” Composites Part A, Vol 37 (2006) p 766-777.
[28] Sleight, D. W., “Progressive Failure Analysis Methodology for Laminated Composite Structures”, NASA TP-1999-209107.
[29] Matzenmiller, A., Lubliner,J., and Taylor, R.L. “A Constitutive Model for Anisotropic Damage in Fiber-Composites,” Mechanics of Materials, vol. 20, pp. 125–152, 1995
[30] Davila, C.G., Camanho, P.P., de Moura, M. F., “Mixed-Mode decohesion elements for analyses of progressive delamination”, NASA/TM-2002–211737, pp. 1–37, 2002
187
[31] Miami P., Camanho P.P., Mayugo J.-A., Davila C.G., “A thermodynamically consistent damage model for advanced composites”, NASA technical memorandum NASA/TM-2006-214282
[32] Singer, J., Arbocz, J., Weller, T., Buckling Experiments: experimental methods in buckling of thin-walled structures, New York Willey, 1998.
Top Related