For
Urgent Special Repairs, Renovations, Additions and Improvements, Minor Works and Maintenance to
Government Buildings- 2014
Department of Buildings
Chief Engineer Estimates, Estimate Division, Dept. of Buildings,
Building Schedule of Rates
B.S.R-2014
" Sethsiripaya", Battaramulla.
B.S.R-2014
BSR 2014- Department of Buildings
S07-2
CONTENTS
* GENERAL NOTES
* PRICING PREAMBLE
* PRELIMINARIES
A DEMOLISHER
B EXCAVATOR
C CONCRETER
D BRICK LAYER
E MASON
F PAVIOR
G ROOFER
H CARPENTER & JOINER
J IRON MONGER
K BRASS FOUNDER
L PLASTERER
M TINKER
N GLAZER
P PAINTER & DECORATOR
Q PLUMBER
R DRAIN LAYER
S MISCELLANEOUS
T ELECTRICAL INSTALLATION
U ALUMINIUM FABRICATOR
* FIGURES
BSR 2014- Department of Buildings
S07-2
* INDEX
BSR 2014- Department of Buildings
S07-2
PAGE
S07-03
S07-06
S07-23
S07-25
S07-28
S07-30
S07-33
S07-35
S07-36
S07-41
S07-45
S07-53
S07-59
S07-62
S07-64
S07-66
S07-67
S07-72
S07-98
S07-102
S07-106
S07-113
S07-156
BSR 2014- Department of Buildings
S07-2
S07-194
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 3
GENERAL NOTES
1.0 Timber :
(Group-1): Door, Window and Fanlight Frames
Category A Satin Palu Milla Ketakala Halmilla Mee Hulanhik Wewarana
Kohomba
Category B Grandis
(Group-2): Door , Window and Fanlight Sashes , Cupboards,
Counters and ShelvingCategory A Satin Tulan Halmilla Mahogany
Kohomba Wewarana Hulanhik Sooriya mara
Category B Ginisapu
(Group-3): Roof Framework
Category A Madan Milla Palu Wewarana
Mee Valdel. Micro Kolon
Category B Domba Grandis
(Group-4): Ceiling Framework and Partitions
Category A Satin Palu Milla Ketakala Halmilla Mee Hulanhik Wewarana
Kohomba Etathimbiri
Category B Domba Grandis
(Group-5): Valance Board and Valley Boarding
Category A Kolon Tulang Val Del Kohomba
Mahogany Satin Hulanhik Wewarana
Category B Ginisapu
(Group-6): Beadings :
Alstonia Mahogany Lunumidella
(Group-7): Special Timber
Category A Teak Category B
Unless otherwise specified in the respective Trades / Sections , the timber for all trades shall be as specified in Carpentry and Joinery.
All timbers under exceptional Circumstances, any equivalent timber to the given Species may be used with the approval of the Engineer.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 4
2.0 Trade Names ;
3.0 Method of Measurement
4.0 Measurements :
5.0 Materials at site (Prime Cost of materials)
6.0 Mark-Up:
7.0 Machinery Usage in Basic Rate
8.0 Hiring of plant and equipment (Other than specified)
Where trade names , brands and / or catalogue numbers are referred to sole preference to any material or equipment is not intended . Any other material or equipment may be used, provided that the characteristics of type, quality, appearance, finish, method of construction and / or performance is not less than specified and provided also that approval is first obtained.
This Bill of Quantities has been prepared generally in accordance with the principles of "Standed Method of Measurement of Building Works(First Revision) , Sri Lanka 573:1999"
Bidders are to note that the measurements are taken absolutely nett, unless otherwise stated and they must , therefore, allow in their prices for all straight cutting and waste, laps, etc. throughout even though not specifically mentioned.
Material rates shall cover all the expenses of Contractor such as Loading, Delivery to site , Unloading, storing and protecting etc.
Combining the factors for overheads and the profits factors 28.8% is obtained from the basic rate as the Overhead and Profit factor, which is also called the " Mark-Up" on the Basic Rate. i.e. the Basic Rate is multiplied by the factor 1.288 to obtain the working rate or the BSR rate.
This basic rate analysis does not include for the use of heavy plant and equipment. This analysis provide for a labour intensive method of work with a minimal use of machinery. The machinery allowed in this analysis is the concrete mixture, the vibrator and a hoist in the case of a multi-storied building for the lift of materials to the various floors.
In case of hiring plant and equipment (Other than specified) in hourly basis. Plant shall be in good working condition and include for the cost of fuel, Lubricants, Transport to and from the site, wages and allowances of the operator, and any other expenses and charges etc.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 5
9.0 Allowances for lifting work
The rates refer to works on the ground floor items in the BSR (other than specified),
Allowances to be made in the rates for lifting respect of work on upper floors.
(a). Ground and 3 upper floors
Serial No. Item
1 Concrete (cube) 3 5
2 9" Brickwork (sqr) 5 7
3 9" Brickwork (cube) 5 7
4 4 1/2" Brickwork (sqr) 5 7
5 Steel reinforcement (cwt) 2.5 5
6 Plastering (sqr) 5 10
7 Floor Tiling (sqr) 2 4
8 Wall Tilling (sqr) 2 4
9 Roof Calicut tile (sqr) 3 6
10 Roof asbestos (sqr) 3 5
11 Ceiling work (sqr) 3 5
12 Painting (sqr) 3 6
(b).Fourth floor and above
B.S.R is limited to work on the ground and 3 upper floors only. In cases, where the rates are not specified beyond ground floor, upto 3rd floor level the percentages indicated in table below should be added to the ground floor rates of relevant trades in the BSR, to obtain the rates applicable to the 1st, 2nd and 3rd floors respectively & in which. Additions beyond the ground floor rates cover the extra costs incurred for raising scaffoldings and involvement of labour for Lifting goods and etc. (Acceptable floor to floor height may be around 12 feet)
Ground to 1st floor %
Ground to 2nd floor %
In case of a building, having more than four floors , It will necessary to be raise a separate scaffolding system in an effective manner, to carryout the exterior works of the building.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 6
TulangValdel.
Tulang
Etathimbiri
TulangValdel.
Sooriya mara
Jak
Unless otherwise specified in the respective Trades / Sections , the timber for all trades shall be as specified in
All timbers under exceptional Circumstances, any equivalent timber to the given Species may be used with the
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 7
Where trade names , brands and / or catalogue numbers are referred to sole preference to any material or equipment is not intended . Any other material or equipment may be used, provided that the characteristics of type, quality, appearance, finish, method of construction and / or performance is not less than specified and
This Bill of Quantities has been prepared generally in accordance with the principles of "Standed Method of
Bidders are to note that the measurements are taken absolutely nett, unless otherwise stated and they must , therefore, allow in their prices for all straight cutting and waste, laps, etc. throughout even though not specifically
Material rates shall cover all the expenses of Contractor such as Loading, Delivery to site , Unloading, storing
is obtained from the basic rate as the " on the Basic Rate. i.e. the Basic Rate is multiplied
This basic rate analysis does not include for the use of heavy plant and equipment. This analysis provide for a labour intensive method of work with a minimal use of machinery. The machinery allowed in this analysis is the concrete mixture, the vibrator and a hoist in the case of a multi-storied building for the lift of materials to the
in hourly basis. Plant shall be in good working condition and include for the cost of fuel, Lubricants, Transport to and from the site, wages and allowances of the
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 8
The rates refer to works on the ground floor items in the BSR (other than specified),
Allowances to be made in the rates for lifting respect of work on upper floors.
7910104.515669779
B.S.R is limited to work on the ground and 3 upper floors only. In cases, where the rates are not percentages indicated in table below should
, to obtain the rates applicable to the 1st, 2nd and 3rd floors respectively & in which. Additions beyond the ground floor rates cover the extra costs incurred for raising scaffoldings and involvement of labour for Lifting goods and etc.
Ground to 3rd floor %
In case of a building, having more than four floors , It will necessary to be raise a separate scaffolding
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 6
1. GENERAL
a.
b.
c.
.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 7
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 8
e.
2. EXCAVATION AND EARTHWORK
a.
b.
c.
d.
e.
f.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 9
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 10
f.
g.
3. CONCRETE WORK
Rates for concrete work shall include for -
FORMWORK
a.
b.
c.
d.
e.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 11
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 12
.
.
REINFORCEMENT
a.
b. Rates for reinforcement shall include for -
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 13
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 14
PRECAST CONCRETE WORKS
a.
i.
ii.
iii
iv.
4. MASONRY WORK
a.
b.
c.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 15
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 16
c1
i.
ii.
iii.
iv.
v.
vi.
vii.
c.2
i. ii. iii.iv.
v. vi. vii.
iix.ix.x.xi.xii.
xiii.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 17
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 18
c.3
i.
ii. iii.
5. WATER PROOFING
a.
b.
c.
d.
e.
f.
6. STRUCTURAL STEELWORK
7. METAL WORKS
a.
b.
c.
d.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 19
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 20
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 21
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 22
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 23
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 24
8. ROOF COVERING AND ROOF PLUMBING
a.
b.
9. CARPENTRY(Roof and ceiling frame)
a.
b.
c.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 25
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 26
d.
e.
f.
10. JOINERY
a.
b.
c.
d.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 27
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 28
f.
g.
11. WALL,FLOOR AND CEILING FINISHES
a.
b.
.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 29
.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 30
c.
d.
12. GLAZINGa
b.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 31
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 32
13. PAINTING AND DECORATING
Note
a.
b.
c.
d.
14. PLUMBING
a.
b.
c.
d.
e.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 33
f.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 34
g.
h.
j.
k.
l.
m.
a.
b.
c.
d
e
DRAINAGE WORK
a.
b.
c.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 35
d.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 36
15. ELECTRICAL INSTALLATIONS
a
b
c
d
e
f
g
h
j
k
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 37
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 38
l
m
n
p
q
r
s
p
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 39
PRICING PREAMBLES
1. GENERAL
The Bidder shall refer to the relevant Clauses of Pricing Preamble when pricing composite item of works.
The rate for each item shall also include for all the following -
i. Labour and all connected costs ;
ii. Materials and goods including all connected costs;
iii. Preparatory works and setting out of particular item ;
VI. Plant and equipment unless otherwise included in Preliminaries ;
vii. Handling of materials and working in situation where there is very restricted working space or no working space ;
viii. Square cutting and Waste of materials ;
ix Forming of ends, angles, miters and junctions between straight and raking or curved work ;
x. Protecting and cleaning ;
The Bidder shall read and be conversant with the full description of workmanship and materials as described in the Particular Specification and ICTAD Specification for the respective items of work/ trades prior to the preparation of the Bid.
The rate for each item must be comprehensive and must include for complying in all respects with the requirements of
the aforesaid specifications, these Pricing Preambles, cover all the obligations under the Contract, and all matters and
things necessary for the proper construction, completion and maintenance of the Works. No claim for additional
payment shall be allowed for any error or misunderstanding by the Contractor of the work involved.
iv. Complying with regulations of the Municipal Council and/or any other relevant authority under which particular item of
work is to be executed unless otherwise included in the Preliminaries ;
v. Fitting and fixing materials and goods in position, including hoisting to any height or lowering to any depth and all temporary works, equipment and small tools ;
xi. All other incidental works and necessary works which are not described in the Maintenance Programme, but described in the aforesaid specifications and or shown in the drawings for the proper completion of the relevant item of work ;
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 40
Contd.,
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 41
2. EXCAVATION AND EARTHWORK
All works under this section are measured net and no working space is allowed.
Dewatering has been measured under Preliminaries.
Rates for Excavation & Earthwork shall include for -
i. Accepting site as found and preparing to condition suitable for proper execution of the Works
iii. Trimming sides, keeping clean and consolidating bottom of basement, sumps, pits and trenches ;
iv. Backfilling and disposal of surplus excavated materials as specified and directed ;
v. Any necessary additional works required due to a. Working space required by the Contractor ; b. Earthworks supports ; c. Formwork ;
xii.Establishment charges and overheads( not included in preliminaries or anywhere in the Bill Of Quantities), and profits.
In addition to above, the rates for items of work in Substructure shall include for the works at depths extending below
ground water table where applicable including excavation under water, removal and disposal of mud and sand and
preparation of place to a condition suitable for proper execution of the works.
The Contractor shall be responsible for the design and execution of the excavation method which is subject to scrutiny
by the Engineer. However, scrutiny by the Engineer shall not in any way relieve the contractor of his responsibilities and
duty of care.
Existing ground levels shown in the Drawings have been taken at the surface of the ground, with no particular differentiation to indicate buried foundations, pavings etc.
The Contractor shall note that the rate for compacted earth fill and granular fill, stone, gravel and sand beds shall include for imported materials or materials from borrow areas.
ii. Excavating by whatever means are necessary including excavation done manually or by machine in any type of ground including ground with boulders (except rock) and excavation around existing RCC. bored piles and jet grout piles ;
vi. Any additional trimming or appropriate back- filling to provide specified or approved formations and profiles
necessitated by the uneven excavation of the earth, unless otherwise measured separately ;
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 42
Contd.,
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 43
3. CONCRETE WORK
Rates for concrete work shall include for -
i. Mixing as per specification, depositing, handling, hoisting and placing at any height or depth ;
iii. Packing and tamping around reinforcement, including vibrating ;
iv. Contractor's designed kickers, construction joints and sealants ;
vi. Curing ;
FORMWORK
Rate for formwork shall include for -
i. Fabricating setting up and erection at any height or depth ;
Rates for compacted earth fill, granular fill and gravel and sand beds shall include for finishing sub-grade to slopes and
falls, depositing in layers, leveling, blinding, and machine or hand-packing to form vertical or battered or level faces,
and for forming sinking where required under floor slabs or sub-floor layers.
Rates for approved damp-proof membrane shall include for laps, and straight, raking and circular cutting, and for notching around all obstructions.
ii. In case of readymix concrete, transporting, admixtures, handling, pumping/hoisting and placing at any height or depth ;
v. Finishing to slopes and falls, and preparing surface ready for screeds or paving, where necessary, including cutting to
sizes and temporary supports to form necessary grooves ;
vii. Preparation of ground surface, grading to slope and falls, if any, and machine or hand packing to form vertical or battered or level surface and all necessary formwork to edges of blinding concrete in case of pile caps ground slab/ramps/beams.
Formwork for similar concrete members are measured together irrespective of the height or depth and the shape or form.
Extra-over rate for a particular type of high quality formwork should be applied only for the areas of formwork which requires such high quality type formwork as specified.
Formwork shall be properly designed and strictly as described in the specifications for the particular type of concrete surface finish and it should be sufficiently strong and grout tight.
Faces of Jet grouting piles, masonry and concrete work which will be formed or used as formwork shall not be measured as formwork and no payment shall be made for same.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 44
Contd.,
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 45
iii Coating with shuttering oil and or lining ;
iv Easing, striking and removing ;
v. Cleaning, preparing for reuse ;
vi. Removal when no longer required ;
vii. Props, stays, struts, wedges, bolts, incidental items and materials such as nails, screws anchors hooks etc. ;
viii. All overlaps and passing at angles ;
ix. Labour at intersections and narrow widths ;
x. Rubbing down and making concrete surface good after removal of formwork ;
xii. Providing samples as required by the Engineer of the different formed finishes specified.
REINFORCEMENT
i. Standard length of reinforcing bar for the purpose of measurement shall be 6.0 m.
ii. Payment for bar reinforcement shall be to be nearest L.ft/ Cwt..
i. Rolling margin ;
ii. Preparation of bar bending schedules (Including laps);
iii. Straightening as required and cleaning of bars ;
iv. Cutting, bending and binding ;
v. Hoisting and placing in position at any height or depth ;
vi. Binding wires, and cover blocks.
vii. Necessary supports such as chairs and spacers.
viii. Aligning and supporting in position during concreting.
ii. Strutting, supporting through lower floors and supporting at any level, including additional propping, strutting and supporting decks ;
xi. All fillets, to form grooves, rebates and throats, splays or chamfers, raking and circular cutting, and cutting around all
pipes, sleeves, conduits, ducting, metal sections and fittings ;
b. Rates for reinforcement shall include for -
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 46
Contd.,
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 47
PRECAST CONCRETE WORKS
Rates for precast concrete works shall include for -
The requirements of the Pricing Preamble clauses which refer to Concrete Work, Reinforcement and Formwork.
Loading, transporting to Site, unloading, handling and stacking.
Hoisting and fixing in position at any height or depth.
4. MASONRY WORK
Rates for brickwork/Block work shall include for -
i. Plumbing, angles, straight cutting, forming rebates, reveals and raking out joints for plastering;
iv. Supplying and fixing metal clamps, Galvanized, steel boundary ties, and brick reinforcement etc.;
v. Necessary cutting required in walls which are not multiples of brick size ;
vi. Preparing existing walls for raising and pinning new brickwork ;
vii. Bonding new walls to concrete faces and old walls where necessary, and materials to be used for such bonding.
Rates for Damp Proof Course shall include for -
i. Necessary leveling screed and trimming top of rubble/block/brick plinth wall ;
Moulds and for formwork with the required finish to all exposed surfaces in accordance with the specifications, hacking
surfaces to form key for rendering etc., and hoisting to any height or depth including providing any lifting holes or other
devices to the approval of the Engineer, building in, including bedding and jointing in mortar as required, and any
necessary strutting and supporting.
In the calculation of the volumes of brick wall which are not multiples of the size of standard bricks, the thickness of
such walls shall be taken as the thickness of full bricks from which they can be cut. The same principle of calculation of
volume shall be used for all brickwork of which the cross-sectional dimensions are not multiple of brick sizes.
ii. Splay cutting, rough cutting, fair cutting, forming chases or grooves for slabs, partitions, staircases, roofs and the like,
bonding ends of walls, building in or cutting and pinning in and making goods on lintels, timber and steel works ;
iii. Building at any level or height of slabs or beams, additional labour in kerbs, isolated and attached piers, all cutting,
bonding at angles and intersections, building into or against adjacent work, wedging and pinning up to soffits;
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 48
ii. Fair edges, rounded edges, drips and arises, angle fillets ;Contd.,
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 49
iii. Turning nibs of asphalt into grooves ;
iv. Cutting to line and jointing new to old asphalt.
Rubble work
Rates for Rubble Masonry shall include for -
All joggles, cramps, dowels, ties, templates ;
Bonding ends of walls, rough cutting and fair cutting ;
Leveling up in walling for Damp Proof Courses, sills, thresholds, string courses, copings and the like ;
Forming straight vertical joints next to dressings, panels, brickwork etc. ;
Forming openings and dressed margins ;
Rates for stone work shall include for:-
Extra material for curved work All rough and fair cutting Dressing Forming rough and fair grooves, throats, mortices, chases, rebates, holes, stops and miters.
Raking out joints for key Labours in eaves filling Dressed margins to rubble work Leveling uncoursed work Rough and fair square cutting Centering Wedging up and pinning to concrete soffits and steel work Building in frames, flashing, damp proof courses including filling hollows of corner blocks with mortar
Building in ties, lugs, plates, lintels, pipe sleeves, inserts, switch boxes and the like. As the work proceeds.
Rubble Stone masonry built of stones either irregular in shape as quarried or shaved and only hammer dressed and having comparatively thick joints.
Plumbing, angles, fair returns, setting, jointing, eaves filling, pointing and fixing in position, hoisting to any given height or depth ;
Forming chases, throats, rebates, margin flutes, sinking, chamfered and rounded edges, and all labour connected therewith.
Ashlar Stone masonry using dressed stone blocks of given dimensions having faces perpendicular to each other and laid in courses.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 50
Contd.,
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 51
Stone Veneering work (Face rubble work)
Stones cut into slabs of required thickness.Dressed to very close tolerances.
5. WATER PROOFING
Rates for Water Proofing shall include for ;
For necessary leveling and trimming top of rubble/block/brick plinth wall ;
Fair edges, rounded edges, drips and arises, angle fillets ;
Forming internal and external angles, bonding bricks/blocks and the like ;
Turning nibs of asphalt into grooves and asphalting around brackets ;
Cutting to line and jointing new to old asphalt ;
Temporary screeds, ground and rules.
6. STRUCTURAL STEELWORK
Rate shall include for :
7. METAL WORKS
General Notes for Metal works
Contractor to prepare shop drawings for approval of the Engineer.
Fabrication & fixing of Aluminum components
Material
Stone lining upto 80mm along planes parallel to natural bed. The natural bed may be masonry of brickwork or rubble work, concrete surface.
All shop fabrication work, including cutting, drilling, bolting, riveting, welding, grinding, delivering, unloading, hoisting, erecting and fixing.
Type and quality of steel to be used for metal work shall be as per drawings and relevant specification clause and or shall conform to latest British Standards.
Rates for Metal Work shall include for anchors, screws, dissimilar metals and providing thermal movement and the
preamble clauses for Structural Steel Work where relevant and they shall apply equally to relevant items of this section.
Fabrication & fixing of Aluminum components shall be carried out by experienced tradesman. The Contractor shall
furnish particulars of Aluminum fabricator through the engineer for his approval.
The Contractor will be required to furnish a guarantee on material and workmanship for a period of 8 years from the date of handing over of Works in the form required by the employer, binding the Aluminum manufacturer and the Contractor jointly and severally
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 52
Contd.,
All Aluminium sections shall be fully treated extruded Aluminium alloy sections in accordance with BS 1470,1471, 1473, 1474 or latest relevant EN standard
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 53
FinishAll Aluminium extrusions shall be accordance with the Manufacturers Mill report.
(1 ) Anodizing or( 2 ) Powder coating ( What ever specified in Aluminium Items )
Rate for Aluminum doors and windows shall include for
i. Glass and glazing
ii. All necessary ironmongery (defined)
iii. Furnishing shop drawings
iv. Furnishing guarantee's as required by the employer
v. Sampling and submission of test reports to the engineer as directed
Screws and Hardware Items
Hardware items such as Hinges, Handles, Catches, fixtures etc., shall be minimum of grade 304 stainless steel.
Glass
WorkmanshipThe fabrication and installation of all Aluminium work must be carried out by specialist tradesmen.
All Aluminium sections shall present clear, straight and sharply defined lines. They shall be free from defects impairing strength, appearance and durability.
All members shall be finished either by
Anodizing -Exposed surface of all members shall be anodized using two steps. Anodizing process to an anodic thickness of not less than 10-15 microns and shall be free of any defects.
Powder coating - Powder coating shall be carried out using polyester coating with proper and appropriate pre- treatment to a coating thickness of not less than 60-80 microns, measured on all significant surfaces.
Concealed screws, nuts, bolts, rivets and other fastening devices shall be of Aluminium, non-magnetic stainless steel or other approved corrosive resistant materials. If visible, they shall blend with the finish of the framing Aluminium sections.
Glazing shall be minimum of 5mm thick clear float glass. Glass shall be secured at all edges with compression gaskets and glazing beads. When fixing glass, all glazing sealant shall be carefully applied and cleaned off properly.
All dimensions shown on the drawings and the shop drawings must be verified by actual site measurement before fabrication and installation. Any cutting to enlarge the size of openings and approved practical method to fill the excess void behind frames required after installation shall be executed by the Contractor at his own expense.
All Aluminium members shall be factory fabricated to the best standard of workmanship under experienced factory supervision and control.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 54
Contd.,
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 55
Submissions
- full size sections of members- methods of assembly- methods of glazing- methods of installation, including fixings caulking, flashing- provisions for vertical and horizontal expansion- junctions and trim to adjoining surfaces- fittings and accessories
Doors & Windows
Aluminium Louvers
The Contractor shall provide a guarantee in respect of the weatherproof properties of the fixed louvers.
Partitions
Materials, method of fabrication, assembly, installation, fastenings, supports, braces, operating parts and the like shall be in accordance with the approved shop drawings.
All joints in frames at corners, junctions and intersections shall be mechanically jointed and be such that when assembled they are as strong and rigid as adjoining sections. Due care must be taken to ensure that all joints are water tight and leak-proof. Joint lines should not be visible.
Provisions must be made for expansion and contraction in horizontal and vertical members which are exposed to the weather or environments. Any distortion of members or any glass cracked or broken as a result of inadequate provisions must be rectified by the Contractor at his own expenses.
All works shall be securely installed and anchored in position, set plumb, square and level in accurate alignment with other work, all in accordance with the approved shop drawings to the Engineer's satisfaction.( The allowable tolerance in terms of specified dimensions shall be plus/minus 1.5mm.)
The Contractor shall submit shop drawings showing the following information where appropriate to the item ; layout (Sectional plan and elevation) of complete assembly
The Contractor shall submit certificates from the Aluminium manufacture and/or an approved testing laboratory which attest that the coating thickness offered is as specified.
Frame and /or sash sections shall be of extruded EN-AW 6063-T5 Aluminium Alloy having a normal thickness of 1.5mm
( Accepted commercial tolerance of tolerance of ± 0.15mm shall apply )
Fixed louvers shall be of the weather proof type, suitable for overcoming water carried- over by wind and the fixed louvers shall have free areas of not less than 50%
All powder coatings shall match the windows. Panels shall be so constructed as to be completely weather proof at junctions with adjoin structures .
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 56
The frames shall be properly machined no permit easy assembly and to form weather-tight joints when caulked.
Partition members shall be 76mm in depth and the thickness of 1.2mm.Contd.,
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 57
Following dimensions are applied for the frame members of each assembly units
Assembly Unit Member Depth Mini. Member Thickness
(mm) (mm)Casement Window, Fanlight 41, 60, 70 1.2
Sliding door/Window 70, 80, 100 1.2
Door 100 1.5
8. ROOF COVERING AND ROOF PLUMBING
Rates for roof covering and roof plumbing shall include for :
i. Hoisting, placing and fixing in position ;
ii. Straight cutting, raking cutting, circular cutting, notching, and working around obstructions and waste ;
iii. Nails, screws and the like ;
iv. Drilling and making holes or opening and the like;
Rates for flashings shall include for the following in addition to the requirement of "a" above -
i. Bending and cutting to required shape and forming roll edges ;
ii. Angles, edges and ends ;
iii. Notching over roofing ribs or dressing into roof cover/concrete as the case may be ;
iv. Forming and dressing into or around walls at obstructions and the like ;
v. Stepping up ;
vi. Sealing with sealant materials.
9. CARPENTRY(Roof and ceiling frame)
Sizes of all timber given are finished sizes.
All timber shall be well seasoned and treated against insect and termite attack beforefixing in position
Rates for carpentry shall include for -
Rates shall include for all necessary hinges, screws, rubber beadings, Skelton bolts, Aluminium louvers, pinhead stickers, etc.
i. Any type of cutting required, sawing, notching, drilling, trimming, framing, jointing, splayed edges and the like,
hoisting and fixing in position with nails, spikes, plugs, screws, and gluing and priming to joints and ends ;
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 58
Contd.,
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 59
ii. Forming splayed edge, grooves, chamfers, scribed and rounded edge, beveling, molding and the like ;
iii. Plugging, wedging, nuts and washers with bolts, sprockets and pins and the like ;
iv. Nogging or solid bridging, cut between studs or joints for structural timber.
v. Rebating, singings, grooving, mortising ;
vi. Additional timber lengths required for carpentry jointing ;
vii. Protection and keeping clean for staining, polishing or painting where applicable ;
10. JOINERY
Sizes of all timber given are finished sizes.
All timber shall be well seasoned and treated against insect and termite attack before fixing.
Rates for Joinery shall include for -
iii. Working to stated sizes, for all short lengths making miters, joints and ends ;
iv. Necessary bolts, dowels metal clips, anchors, grips and fixing joinery ;
v. Gluing, dowelling, plugging, wedging pining and the like ;
vi. Punching heads and filling with approved filler if nails or pins are used for fixing ;
Rates for roof decking shall include for machine sanding, protecting and preparing in addition to the requirements c above.
Rates for walls and ceiling lining shall include for jointing and fixing to walls/ ceiling/ eaves etc. all cover and joint strips, in addition to the requirements c above.
Rates for timber paneling/wall lining shall include for cover moldings, sills, stiles and head moldings to openings as relevant.
Timber used for joinery works shall be well seasoned well treated and in one species of special class timber
recommended for the particular class of Joinery works as specified in the Specification.(Quality should be assured
through Sampling and test reports)
i. Any type of cutting required, sawing, notching, drilling, trimming, planning, forming and jointing and the like, fixing in
position complete with nails, spikes, plugs, screws and gluing and priming to joints and ends ;
ii. Forming splayed and tongued edges, rebates mortises, grooves, chamfers, scribed and rounded edges, beveling,
moulding, margin and the like and rounded corners, sinkings ;
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 60
vii. Countersinking and filling heads with approved filler, if brass screws are used for fixing ;
Contd.,
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 61
viii. Painting rebates of frames before fixing glass ;
ix. Bedding in cement mortar filling and hanging to frame lining ;
x. Keeping clean for staining, polishing or painting;
xi. Painting, Lacquering or Varnishing as specified.
Preambles for Glazing section and a, b and c under Painting and Decorating section shall
equally apply to Joinery works.
Ironmongery
i. All cutting, fitting, sinking, boring, mortising ;
ii. Matching screws for ironmongery
11. WALL,FLOOR AND CEILING FINISHES
Rates for wall, floor, ceiling finishings and wall floor screed and bedding shall include for -
iii. Tamping and compacting ;
v Forming internal and external angles and arises ;
vi. Any extra thickness required to finish to true levels ;
iii Removing during decoration, refixing after decoration, leaving oil and in proper working order on completion and
supplying and labeling all keys and handing over to Employer.
i. All works under this trade shall be measured in Sq.ft/ Sqr. after deduction for voids, openings, doors and windows
ii. All other small quantities/panels/narrow widths/ arises/ reveals/ angles/ ends/short lengths including those of tiling
work on door and window jambs and reveals are measured together with the respective tiling item and labour in such
work shall be included in the rate for the main finishing item and they shall not be measured/paid separately.
i. All temporary rules, screeds, templates and supports, curing and cleaning off on completion and exact thickness required to finish ;
ii. Caulked joints and making good and cutting around bolts, pipes conduits, sleeves, ducting, fittings, sections, obstructions and the like ;
iv. Raking out joints of new brickwork/Block work or hacking concrete to form key, including brushing, cleaning off and dampening ;
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 62
Contd.,
vii Any additional dubbing out required to plastered surfaces of brickwork and to the finished surface of concrete to obtain the requisite standard of finish ;
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 63
viii. Samples to be submitted for the approval of the Engineer.
Rates for tile slab or block finishing to floor and wall shall also include for the following in addition to the above -
i. Straight raking and circular cutting ;
ii. Dubbing out or packing to concrete surface to correct deviations within specified tolerance ;
iii. Laying or finishing to falls or cross falls ;
iv. Expansion joints at perimeter and between bays where required in case of floor tile paving ;
v. Sand blasting, cleaning, waxing and appropriate floor finishings.
Rates for ceiling lining shall include for the following
i. Working to sides and soffits of attached or isolated beams and soffit of staircases where relevant;
ii. Additional forming required for lighting and air-conditioning grills ;
iii. Straight, raking and circular cutting ;
iv. Neoprene sealing for air tightness around hatches if any ;
v. Matching edges where cutting occurs and for filling the heads of fixings with approved filler where relevant ;
vi Painted mild steel hanging rods.
12. GLAZING .i. Type of Glazing shall be as specified.
Rates for Glazing shall include for -
i. Glazing, fixing, bedding priming and panel pins and other materials and labour for same and cutting to size ;
ii. Templates, straight cutting, circular cutting, grinding edges or special type of edges required and sand blasting ;
iii. Glazing beads, washlether or neoprene strip, glazing sealant, weather stripping, caulking joint silicone joint ;
iv. Replacing cracked or broken glass ;
ii. Thickness of glazing shall be as per the design of the approved specialist contractor who will be engaged by the
Contractor. However, the minimum thickness shall be 6mm, unless otherwise stated.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 64
Contd.,
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 65
v. Making holes where necessary ;
vi. Samples to be submitted for the approval of the Engineer.
13. PAINTING AND DECORATING
NoteColour and the quality of all paint and other painting materials shall be approved by the Engineer prior to use.
Rates for painting shall include for -
i. Preparation of surfaces, cleaning down, smoothing, etc. ;
ii. Submission of samples for the approval of the Engineer ;
iii. Protection of floors, walls and fittings etc. ;
v. Cleaning down upon completion
14. PLUMBING
The rates for Plumbing shall include for :
Refer specifications for full description of materials and workmanship.
Short lengths, joints connections and couplers in running length.
Sealing, fixing and support with holder bats or pipe clips cut and pinned built in wall or slabs.
Plugging screwing to walls or ceiling
iv. Working to returns, painting in any colour, multi- colour works, cutting into line at junctions of different colours at angles or plain surfaces, painting in small quantities ;
Rates for work to isolated general surfaces shall include for working on door frames, linings, window sub frames (where
of a differing material to the window), skirting, rails, architrave's, bars, posts, balusters and the like.
Rates for work to glazed general surfaces, glazed windows and the like (measured both sides, flat over glass,
irrespective of size and panes) shall include for work to edges and glazing rebates, returns and moldings of frames,
mullions, transoms, architraves and the like.
Rates for work to pipes and conduits (which shall include trunking, ducting and the like) shall include for all work on hangers, supports, brackets and the like.
Screws, nails, sockets, connectors, backnuts, nipples, and standard pipe fixing or supporting clips, saddles, brackets
straps, screws, nails, solder rivets connectors, flanges pipe sleeves, brackets, made bend holder bats and the like.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 66
All laps, straight cutting and wasteContd.,
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 67
Jointing compound, solvent cement and incidental materials and labour.
Connecting pipes to sanitary fixtures and appliances.
Testing and disaffection after completion.
Rates for sanitary fittings shall include for
Jointing and or connecting pipes to sanitary fittings.
DRAINAGE WORK
The provisions and the clauses of precedence trades shall equally apply to relevant item of this trade.
The fittings including bends, tees, collars, reducers elbows, valve sockets, junctions, caps and the like for pipe less than or equal 50mm dia pipe.
Standard and special pipe fixing arrangement where necessary fittings, supporting clips, saddles, brackets, holder bats
straps ,rowl plugs, brackets, nails, anchor bolts etc.
All builders works such as chasing and forming holes through brick work/ block work/ foundations and concrete slabs
beams columns floor slabs manholes and like and making good all damages.
Fittings such as taps, waste water outlet, flushing cistern, internal overflows and the like and supporting brackets, incidental materials for fixing.
Assembling, jointing together, fixing components parts and jointing to pipes including necessary coupling and for leaving
perfectly clean undamaged and in perfect working order as on completion.
Any special water supply and drainage fittings such as bends, tees, reducers etc. unless otherwise specified separately
in the Bill of Quantities, shall be deemed to have been included in the relevant items and such items should accordingly
be rated to include for such specials etc. and for any extra work involved and the satisfactory completion of such items.
Where pipes pass through walls or slabs these shall be wrapped with a layer of inert materials. For pipes exceeding 50
mm dia sleeve pipes shall be used for the full thickness of slabs, walls or beams through which the pipes pass.
The rates for trench excavation for pipes shall include for depending and widening the trench as necessary to enable
the barrels of pipes of rest on firm and to facilitate jointing.
The rates for rock excavation in trench excavations shall include for importing selected materials to replace any
excavated rock which is unsuitable for back filling and for all additional rock excavation and appropriate filling beyond
the maximum measurable in accordance with the specification.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 68
The rates for concrete beds and surrounds to pipes shall include for flexible joints and any necessary formwork where required by the specification.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 69
15. ELECTRICAL INSTALLATIONS
The rates for cables and the like laid in benches shall include for drawing through conduits or ducts where required.
The execution of Electrical Installation shall every respect comply with the current Regulations of the Institute of
Electrical Engineers, London, requirements of Ceylon Electricity Board and the area Authority.
The rates for equipment and control area, distribution boards, meters, switches, fuses, etc. shall include for connecting
up, fixings and supports for the complete installation and for suitable mounting boards, frames, supports, housings and
cabinets where required.
The rates for cables, tape, bus-bar trunking etc. (except where included in sub circuits or electrical points) and the like
shall include for joints in the running length, all allowances for sagging snaking, for drawings through conduits, laying in
trunking of surface fixing where retired with cable supports, clears, hangers, channels, insulators and the like.
The rates for cable terminations shall include for all connections point boxes, insulating and jointing materials, cable terminations glands, lock nuts, bushes and the like.
The rates for conduits trunking cable tray etc. (except where included in sub circuits of electrical points) and the like
shall include for all short lengths, joints and couplers in the running length, and for all fixings and supports with
approved saddles, crumpets, clips and the like cut and pinned, built-in or plugged and screwed to walls or ceilings
including chasing brick work, block work, concrete slab beams walls columns and the like and make good.
The rates for conduits and the like shall include for all bends, tees, socket and the like, cutting, screwing, threading,
jointing and providing all conduit boxes, junction boxes and the like.
The rates for the installation of sub main circuits, lighting points switched points, socket outlets, fused spur outlets,
isolators, etc. (other than those applicable to the distribution switch gear) shall include where applicable, for all conduit,
trunking, cable tray, cabling, terminations, fixings and connections from the distribution switched gear to and including the point (accessories measured separately) and shall be deemed to include for any
item mentioned in the Electrical installation Specification but not shown on the drawings and vice-versa.
The rates for lighting fittings, fittings such as ceiling fans and extract fans, and for appliances such as air- conditioning
units shall include for assembly, fixing and connection from the spur outlet or isolator to the fitting or appliance with all
necessary additional wiring earthing and outlet roses and leaving perfectly clean and undamaged on completion.
The rates for fixing only fittings and appliances provided by the employer should include in addition to the foregoing for
accepting delivery, storing and handling the fittings and providing any additional materials and internal wiring.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 70
Contd.,
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 71
The rates for power outlets shall include for mounting boxes and frames.
The rates for power switched with remote outlets shall include for the additional outlet plates and boxes.
The rates for switched socket outlets shall include for 1 No fused plug top and 4 No fuse links.
Painting of timber work and metal work.
i. The preceding clauses of this trade where relevant.
ii. Preparation of as built drawings to be submitted to Employer at the handingover/ practical completion.
iii All items and accessories required for proper installation as per specification and regulation up to load point and labour connected therewith.
iv. All wiring, conducting and cables and labour connected therewith if not measured separately.
v Items specified in the specification but not shown in the drawings.
vi Disconnecting and refixing of electrical fitting and appliances as required for the convenience of other trades.
vii Painting of timber work metal work executed under this trade.
Rate to include submission of Megar Test report of the building Electrical Installation from Charted Electrical Engineer
The rates for connections only to fittings and appliances such as pumps, water heaters, air conditioning units and
extract fans shall include for connection from the isolator or spur outlet to the fitting or appliance (these being measured
separately) , with all necessary additional wiring, earthing and outlet roses.
The preceding preambles shall apply equally to auxiliary installations such as TV installations, telephone installations, and bell signal systems.
If the items of electrical installation are measured as sub circuit point wiring or in electrical points, the rates for such items shall include for :
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 23
PRELIMINARIES
1
2 Necessary protective fencing, lighting, watchmen and other precautions.
3
4 Erection of temporary sheds for protection and storage of materials and plants.
5 Temporary sheds and sanitary accommodations for workmen.
6 Setting out works
7 Insurance against workman's compensation.
8 Insurance against accidents and injury to workmen , property , material work .
9 Insurance of materials and work at site.
10 Cost of preparing bid.
11 Cost of stamps etc. for contract agreement.
12
13 Erection of Notice Board.
14 Supply of water for use in the work.
15 Charts , Schedules and the like showing time progress, organization of trades of similar matters.
16 Temporary electricity to site
17 Payment of pay roll, sales , receipts and other taxes.
18 Temporary roads , tracks, crossings, planked footways and the like and maintenance.
19 Expenses in connection with general foreman and other site staff.
20 Expenses in connection with security bonds, performance bonds, guarantees, mobilization fees, etc.
21
The preliminaries given below have been considered for the rates in the items of various trades in the Building Shedule of Rates.
Giving notices to authorities etc. Payment of fees , compliance with by lows and regulations lawfully imposed by local authorities.
Erection of 1 Nr. Temporary office with sanitary and electricity facilities for the use of person acting on behalf of the employer.
Removal of all rubbish and debris, clearing up the site and leaving building clean internally and externally.
Extra Payment on labour losses in connection to workmen where required for special conditions, distant camping, dirty work and the like.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 24
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 25
22 Losses rising from restriction to site.
23
24 Erecting, maintaining and dismantling scaffolding.
25 Attendance upon, cutting away for and making good after all trades.
26
27
28 Liability of the builder for making good defects after practical completion.
29 Safety of workers - Safety nets, boots, helmets, head gears , safety goggles etc.
Attendant labour and Hire of plant and equipment such as Weter pump with necessary accessories for working order.Welding Plant, Hammer drill, Jack hammer, Compressor etc.
Protecting and safeguarding the works, materials and plant against the effect of the weather and against damage, trespass or theft.
Duties of the builder on completion including such matters as cleaning and leaving all in good order, labeling over keys, handing over certificates, guarantees and the like.
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 26
Necessary protective fencing, lighting, watchmen and other precautions.
Erection of temporary sheds for protection and storage of materials and plants.
Temporary sheds and sanitary accommodations for workmen.
Insurance against accidents and injury to workmen , property , material work .
Insurance of materials and work at site.
Cost of preparing bid.
Cost of stamps etc. for contract agreement.
Erection of Notice Board.
Supply of water for use in the work.
Charts , Schedules and the like showing time progress, organization of trades of similar matters.
Temporary electricity to site
Payment of pay roll, sales , receipts and other taxes.
Temporary roads , tracks, crossings, planked footways and the like and maintenance.
Expenses in connection with general foreman and other site staff.
Expenses in connection with security bonds, performance bonds, guarantees, mobilization fees, etc.
The preliminaries given below have been considered for the rates in the items of various
Giving notices to authorities etc. Payment of fees , compliance with by lows and regulations lawfully
Erection of 1 Nr. Temporary office with sanitary and electricity facilities for the use of person acting on
Removal of all rubbish and debris, clearing up the site and leaving building clean internally and
Extra Payment on labour losses in connection to workmen where required for special conditions, distant
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 27
Contd.,
BSR 2014- Department of Buildings
Esti Rana / BSR 2014 S07 - 28
Losses rising from restriction to site.
Erecting, maintaining and dismantling scaffolding.
Attendance upon, cutting away for and making good after all trades.
Liability of the builder for making good defects after practical completion.
Safety of workers - Safety nets, boots, helmets, head gears , safety goggles etc.
Attendant labour and Hire of plant and equipment such as Weter pump with necessary accessories for
Protecting and safeguarding the works, materials and plant against the effect of the weather and
Duties of the builder on completion including such matters as cleaning and leaving all in good order,
BSR 2014- Department of Buildings
S07- 25
A001
A002A003
A004
A005A006A007
A008
A009
A010
A011
A012
A013
A014
A015
A016A017A018
A019A020
A021
A022
A023
Item Code
Author: Eng. D.N.Ranaweera
BSR 2014- Department of Buildings
S07- 26
Item Code
A024
A025
A026A027
A028
A029
A030
A031
A032
A033A034
A035
A036
A037
A038
A039
A040
A041
A042
A043
A044
BSR 2014- Department of Buildings
S07- 27
Item Code
A045
BSR 2014- Department of Buildings
S07- 28
Item Code
A046
A047
A048
A049
A050
A051
BSR 2014- Department of Buildings
S07- 29
Item Code
B001
B002
B003
B004
B005
B006
B007
B008B009B010B011B012
B013
B014
B015
B016
B017
BSR 2014- Department of Buildings
S07- 30
Item Code
B018
B019
B020
B021
BSR 2014- Department of Buildings
S07- 31
Item Code
C001
C002
C003
C004
C005
C006
C007
C008
C009
C010
C011
C012
C013
C014
C015
C016
BSR 2014- Department of Buildings
S07- 32
Item Code
C017
C018
C019
C020
C021
C022
C023
C024
C025
C026
C027
C028
C029
C030
C031
C032
C033
C034
C035
C036
BSR 2014- Department of Buildings
S07- 33
Item Code
C037
C038
C039
C040
C041
C042
C043C044C045
C046
C047
C048
C049
C050
C051
C052
BSR 2014- Department of Buildings
S07- 34
Item Code
C053
BSR 2014- Department of Buildings
S07- 35
Item Code
D001
D002D003
D004
D005D006D007
D008D009
D010D011D012D013
D014
D015
D016
D017
D018
D019
D020
D021
D022
D023
D024
BSR 2014- Department of Buildings
S07- 36
Item Code
D025
D026
D027
D028D029D030D031
BSR 2014- Department of Buildings
S07- 37
Item Code
E001E002E003
E004
E005
E006
E007
E008
E009
E010
BSR 2014- Department of Buildings
S07- 38
Item Code
F001F002
F003
F004
F005
F006
F007
F008F009F010F011
F012
F013F014
F015F016F017
BSR 2014- Department of Buildings
S07- 39
Item Code
F018F019F020F021
F022F023F024
F025F026F027
F028F029
F030
F031
F032
F033
F034
F035F036
BSR 2014- Department of Buildings
S07- 40
Item Code
F037
BSR 2014- Department of Buildings
S07- 41
Item Code
F038F039F040F041F042
F043F044F045F046
F047
F048
F049
F050
F051
F052
F053F054
F055
F056
BSR 2014- Department of Buildings
S07- 42
Item Code
F057
F058
F059
F060
F061
F062
F063
F064
F065
F066
F067F068
F069
BSR 2014- Department of Buildings
S07- 43
Item Code
F070
F071
F072
BSR 2014- Department of Buildings
S07- 44
Item Code
G001
G002
G003
G004
G005
G006
G007
G008
G009
G010
G011
G012
BSR 2014- Department of Buildings
S07- 45
Item Code
G013
G014
G015
G016
G017
G018
G019
G020
G021
G022
G023
G024
G025
G026
G027
G028
G029
G030
BSR 2014- Department of Buildings
S07- 46
Item Code
G031
G032
G033
G034G035G036
G037
G038
G039
G040G041
G042
G043
G044G045G046G047G048
G049G050G051G052
G053
BSR 2014- Department of Buildings
S07- 47
Item Code
G054
G055
G056
G057
G058
G059
G060
G061
BSR 2014- Department of Buildings
S07- 48
Item Code
H001
H002
H003
H004
H005
H006
H007
H008
H009
H010
H011
H012
H013
H014
H015
BSR 2014- Department of Buildings
S07- 49
Item Code
H016
H017H018
H019
H020
H021
H022
H023H024
H025
H026
H027
H028
H029
BSR 2014- Department of Buildings
S07- 50
Item Code
H030H031
H032
H033
H034
H035
H036
H037
H038
H039
H040
H041
H042
H043
H044
BSR 2014- Department of Buildings
S07- 51
Item Code
H045
H046
H047
H048
H049
H050
H051
H052
H053
H054
H055
H056
H057
H058H059H060
H061
H062
H063
BSR 2014- Department of Buildings
S07- 52
Item Code
H064
H065H066
BSR 2014- Department of Buildings
S07- 53
Item Code
H067
H068
H069
H070
H071
H072
H073
H074
H075
H076
H077
H078
H079
BSR 2014- Department of Buildings
S07- 54
Item Code
H080
H081
H082
H083
H084
H085
H086
H087
H088
H089
H090
H091
H092
H093
H094
BSR 2014- Department of Buildings
S07- 55
Item Code
H095
H096
H097
H098
H099
H100
H101
H102
H103
H104
H105
H106
H107
H108
H109
H110
H111H112
H113
BSR 2014- Department of Buildings
S07- 56
Item Code
H114
H115
H116
H117
H118
H119
H120H121H122
H123
H124
BSR 2014- Department of Buildings
S07- 57
Item Code
J001J002J003
J004
J005
J006
J007J008J009J010J011J012
J013
J014
J015
J016
J017J018J019J020J021
J022J023
J024
BSR 2014- Department of Buildings
S07- 58
Item Code
J025J026
J027J028J029
J030
J031
J032
J033
J034
J035
J036
J037
J038
J039
J040
J041J042
J043
J044
J045
BSR 2014- Department of Buildings
S07- 59
Item Code
J046
J047
J048
J049
J050
J051
J052
J053
J054
J055J056
J057J058J059J060J061
J062
J063
J064
J065
J066
J067
J068
BSR 2014- Department of Buildings
S07- 60
Item Code
J069
J070
J071
J072
J073J074
J075
J076
J077
J078
J079
J080
J081
J082
J083
J084
BSR 2014- Department of Buildings
S07- 61
Item Code
J085
J086
J087
J088
J089
J090
J091
J092
J093
J094
BSR 2014- Department of Buildings
S07- 62
Item Code
J095
J096
J097
J098
J099
J100
J101
J102
J103
J104
J105
BSR 2014- Department of Buildings
S07- 63
Item Code
K001
K002
K003
K004
K005
K006
K007K008K009K010
K011
K012
K013
K014
K015
K016
K017
K018
K019K020K021
K022
K023
BSR 2014- Department of Buildings
S07- 64
Item Code
K024
K025
K026
K027
K028
K029
K030
K031
K032K033
K034
K035
K036K037K038
K039K040
K041K042K043
K044K045
K046
K047
BSR 2014- Department of Buildings
S07- 65
Item Code
K048
K049
K050
K051K052K053
K054
K055
K056
K057
K058
BSR 2014- Department of Buildings
S07- 66
Item Code
L001
L002
L003
L004
L005L006L007
L008
L009
L010
L011L012
L013
L014
L015L016
L017L018L019L020L021L022L023L024
L025
L026
BSR 2014- Department of Buildings
S07- 67
Item Code
L027
BSR 2014- Department of Buildings
S07- 68
Item Code
L028
L029
L030
L031
L032
L033L034
BSR 2014- Department of Buildings
S07- 69
Item Code
M001
M002
M003
M004
M005M006M007
M008
M009
M010
M011
M012
M013
M014M015M016M017M018
M019
M020
M021
BSR 2014- Department of Buildings
S07- 70
Item Code
M022
M023
M024M025
M026
M027
M028M029
M030
M031
M032
M033
M034
M035
M036
M037
M038
M039
BSR 2014- Department of Buildings
S07- 71
Item Code
N001
N002
N003
N004
N005
N006
BSR 2014- Department of Buildings
S07- 72
Item Code
P001
P002
P003
P004
P005
P006
P007
P008
P009
P010
P011
P012
P013
BSR 2014- Department of Buildings
S07- 73
Item Code
P014
P015
P016
P017
P018
P019
P020
P021
P022
P023
P024
P025
P026
P027
P028
P029
P030
P031
P032
BSR 2014- Department of Buildings
S07- 74
Item Code
P033
P034
P035
P036
P037
P038
P039
P040
P041
P042
P043
P044
P045
P046
P047
P048
BSR 2014- Department of Buildings
S07- 75
Item Code
P049P050P051
BSR 2014- Department of Buildings
S07- 76
Item Code
P052
P053
P054P055
P056
P057
P058
P059
P060
P061
P062
P063
P064
P065
P066
P067
P068
P069
P070
BSR 2014- Department of Buildings
S07- 77
Item Code
P071
BSR 2014- Department of Buildings
S07- 78
Item Code
P072
P073
P074
P075
P076
BSR 2014- Department of Buildings
S07- 79
Item Code
Q001Q002Q003Q004
Q005
Q006Q007Q008Q009Q010
Q011
Q012Q013
Q014
Q015Q016
Q017
Q018
Q019
Q020
BSR 2014- Department of Buildings
S07- 80
Item Code
Q021
Q022
Q023
Q024
Q025
Q026
Q027
Q028
Q029
Q030
Q031
Q032
Q033
Q034
Q035
Q036
Q037Q038Q039Q040Q041Q042
Q043Q044Q045
BSR 2014- Department of Buildings
S07- 81
Item Code
Q046
Q047
Q048
Q049
Q050
Q051
Q052
Q053
Q054
Q055
Q056
Q057
Q058
Q059
Q060
Q061
Q062
Q063Q064
BSR 2014- Department of Buildings
S07- 82
Item Code
Q065Q066Q067Q068Q069
BSR 2014- Department of Buildings
S07- 83
Item Code
Q070
Q071
Q072
Q073
Q074
Q075
Q076
Q077
Q078
BSR 2014- Department of Buildings
S07- 84
Item Code
Q079
Q080
Q081
Q082
Q083
Q084
BSR 2014- Department of Buildings
S07- 85
Item Code
Q085
Q086
Q087
Q088
Q089
Q090
Q091
Q092
BSR 2014- Department of Buildings
S07- 86
Item Code
Q093
Q094
Q095
Q096
Q097
Q098
Q099
Q100
Q101
Q102
Q103
Q104
Q105
BSR 2014- Department of Buildings
S07- 87
Item Code
BSR 2014- Department of Buildings
S07- 88
Item Code
Q106
Q107
Q108
Q109
Q110
Q111
Q112
Q113
Q114
Q115
Q116
Q117
Q118
Q119
Q120
BSR 2014- Department of Buildings
S07- 89
Item Code
Q121
Q122
Q123
Q124
Q125Q126
Q127
Q128
Q129
Q130
Q131
Q132
BSR 2014- Department of Buildings
S07- 90
Item Code
Q133
Q134
Q135
Q136
Q137
Q138
BSR 2014- Department of Buildings
S07- 91
Item Code
Q139
Q140
Q141
Q142
Q143
Q144
Q145
Q146
BSR 2014- Department of Buildings
S07- 92
Item Code
Q147
Q148Q149
Q150
Q151
Q152
Q153
Q154
Q155
Q156
Q157Q158Q159Q160
Q161
Q162
BSR 2014- Department of Buildings
S07- 93
Item Code
Q163
Q164
Q165
Q166
Q167
Q168
Q169
Q170
Q171
Q172
Q173
BSR 2014- Department of Buildings
S07- 94
Item Code
BSR 2014- Department of Buildings
S07- 95
Item Code
Q174
Q175
Q176
Q177
Q178
Q179
Q180
Q181
Q182
Q183
Q184
Q185
BSR 2014- Department of Buildings
S07- 96
Item Code
Q186
Q187
Q188
Q189
Q190
Q191
Q192
Q193
Q194
Q195
Q196
Q197Q198Q199Q200
BSR 2014- Department of Buildings
S07- 97
Item Code
Q201Q202Q203
Q204Q205Q206Q207Q208Q209Q210Q211Q212Q213
Q214
Q215Q216Q217Q218Q219Q220Q221
Q222
Q223Q224
Q225
Q226
Q227
Q228
Q229Q230
Q231Q232Q233Q234Q235
BSR 2014- Department of Buildings
S07- 98
Item Code
Q236
Q237Q238Q239Q240Q241Q242Q243
Q244Q245Q246Q247Q248Q249Q250
Q251
Q252
Q253
Q254
Q255
Q256
Q257
Q258
Q259
Q260
BSR 2014- Department of Buildings
S07- 99
Item Code
Q261Q262Q263
Q264
Q265
Q266Q267
Q268
Q269Q270Q271Q272Q273Q274Q275
Q276Q277Q278Q279Q280Q281Q282Q283Q284Q285Q286Q287Q288Q289
Q290
Q291
BSR 2014- Department of Buildings
S07- 100
Item Code
Q292
Q293
Q294
Q295Q296Q297
Q298
Q299
Q300
Q301
Q302
Q303
Q304
Q305
Q306
BSR 2014- Department of Buildings
S07- 101
Item Code
Q307
Q308Q309Q310Q311Q312Q313
Q314Q315Q316Q317Q318
Q319
Q320
Q321
Q322
Q323
Q324
Q325
BSR 2014- Department of Buildings
S07- 102
Item Code
Q326
Q327
Q328
Q329
Q330
Q331
Q332
Q333
Q334
Q335
BSR 2014- Department of Buildings
S07- 103
Item Code
Q336Q337Q338Q339
Q340
Q341
BSR 2014- Department of Buildings
S07- 104
Item Code
Q342
Q343
Q344
Q345Q346
Q347
Q348Q349Q350Q351Q352Q353Q354
Q355Q356Q357Q358Q359Q360Q361
Q362Q363Q364Q365
Q366Q367
Q368Q369Q370Q371
BSR 2014- Department of Buildings
S07- 105
Item Code
Q372Q373Q374
Q375Q376Q377Q378Q379Q380Q381
Q382Q383Q384Q385Q386Q387Q388
Q389Q390Q391Q392Q393Q394Q395
Q396Q397Q398Q399Q400Q401Q402Q403
Q404
Q405
Q406
Q407
BSR 2014- Department of Buildings
S07- 106
Item Code
Q408
Q409
BSR 2014- Department of Buildings
S07- 107
Item Code
Q410Q411Q412Q413Q414Q415Q416
Q417Q418Q419Q420Q421Q422Q423Q424Q425Q426Q427Q428Q429Q430
Q431
Q432
Q433
Q434
Q435
Q436
Q437
Q438
Q439
Q440
BSR 2014- Department of Buildings
S07- 108
Item Code
Q441
Q442
Q443
Q444
Q445
Q446
Q447
Q448
Q449Q450Q451Q452Q453
Q454
Q455
Q456
Q457Q458
Q459
Q460
Q461
Q462
BSR 2014- Department of Buildings
S07- 109
Item Code
Q463
Q464
Q465
Q466
Q467
Q468
Q469Q470
Q471
Q472
Q473
Q474
Q475
Q476
BSR 2014- Department of Buildings
S07- 110
Item Code
Q477
Q478
BSR 2014- Department of Buildings
S07- 111
Item Code
R001R002R003
R004
R005
R006
R007
R008
R009
R010
R011
R012
R013
BSR 2014- Department of Buildings
S07- 112
Item Code
R014
BSR 2014- Department of Buildings
S07- 113
Item Code
R015
R016
R017
R018
R019
R020R021
R022
R023R024
R025R026
R027R028
R029
R030
R031
R032
R033
BSR 2014- Department of Buildings
S07- 114
Item Code
R034
R035
R036
R037
R038
R039
R040
R041
R042
R043R044
R045
R046
R047
R048
R049
R050
R051
R052
R053
R054
R055
BSR 2014- Department of Buildings
S07- 115
Item Code
R056
R057
R058
R059
R060
R061
R062
R063
R064
R065
R066
R067
R068
R069
BSR 2014- Department of Buildings
S07- 116
Item Code
R070
BSR 2014- Department of Buildings
S07- 117
Item Code
S001
S002
S003S004S005
S006
S007
S008S009
S010
S011
S012
S013
S014
S015
S016
S017
BSR 2014- Department of Buildings
S07- 118
Item Code
S018
S019
S020
S021
S022
S023
S024
S025S026
S027
S028
S029
S030
S031
S032
S033
BSR 2014- Department of Buildings
S07- 119
Item Code
S034
BSR 2014- Department of Buildings
S07- 120
Item Code
S035
S036
S037
S038
S039S040S041S042S043S044S045
S046S047S048S049S050S051
S052S053S054S055S056S057
S058
S059
S060
S061
S062
BSR 2014- Department of Buildings
S07- 121
Item Code
S063
S064
S065
S066
S067
S068
S069S070
S071
S072S073S074S075S076
S077
S078
S079
BSR 2014- Department of Buildings
S07- 122
Item Code
BSR 2014- Department of Buildings
S07- 123
Item Code
T001T002T003T004T005T006
T007T008T009
T010T011T012T013T014T015
T016T017T018
T019
T020
T021
BSR 2014- Department of Buildings
S07- 124
Item Code
T022
T023
T024
T025
T026
T027
T028
T029
T030
T031
T032
T033
T034
T035
T036
T037
T038
T039
T040
T041
T042
BSR 2014- Department of Buildings
S07- 125
Item Code
T043
BSR 2014- Department of Buildings
S07- 126
Item Code
T044T045T046T047T048T049T050T051T052T053T054T055T056T057
T058T059T060T061T062T063T064T065T066
T067T068T069T070T071T072T073
T074T075T076T077T078
BSR 2014- Department of Buildings
S07- 127
Item Code
T079T080T081T082T083T084T085T086T087
T088
T089
T090T091
T092
T093
T094
T095
T096
T097T098
T099
T100
T101
T102
T103
T104
BSR 2014- Department of Buildings
S07- 128
Item Code
T105
T106
T107
T108
T109T110T111
T112T113T114T115T116T117T118T119T120T121
T122
T123
T124
T125
T126
T127
T128T129
BSR 2014- Department of Buildings
S07- 129
Item Code
T130T131
T132T133T134T135T136T137
T138T139T140T141T142T143T144T145T146
T147T148T149T150T151T152T153T154
T155T156T157T158
T159T160
BSR 2014- Department of Buildings
S07- 130
Item Code
U001
U002
U003
U004
U005
U006
U007
U008
BSR 2014- Department of Buildings
S07- 131
Item Code
U009
BSR 2014- Department of Buildings
S07- 132
Item Code
U010
U011
U012
U013
U014
U015
U016
U017U018U019U020U021
U022U023U024U025
BSR 2014- Department of Buildings
S07- 133
Item Code
U026
BSR 2014- Department of Buildings
S07- 134
Item Code
U027U028U029U030U031
U032U033U034U035U036
U037U038U039U040U041
U042U043U044U045
BSR 2014- Department of Buildings
S07- 135
Item Code
U046
BSR 2014- Department of Buildings
S07- 136
Item Code
U047U048U049U050U051
U052U053U054U055U056
U057U058U059U060U061
BSR 2014- Department of Buildings
S07- 137
Item Code
U062U063U064U065U066
U067U068U069U070U071
BSR 2014- Department of Buildings
S07- 138
Item Code
U072U073U074U075U076
U077U078U079U080U081
BSR 2014- Department of Buildings
S07- 139
Item Code
U082U083U084U085U086
U087U088U089U090U091
BSR 2014- Department of Buildings
S07- 140
Item Code
U092U093U094U095U096
U097U098U099U100U101
U102U103U104U105U106
BSR 2014- Department of Buildings
S07- 141
Item Code
U107U108U109U110U111
U112U113U114U115U116
U117U118
BSR 2014- Department of Buildings
S07- 142
Item Code
U119U120
BSR 2014- Department of Buildings
S07- 143
Item Code
U121
U122U123U124U125U126
U127U128U129U130U131
U132U133U134U135U136
BSR 2014- Department of Buildings
S07- 144
Item Code
U137U138U139U140U141
U142U143U144U145U146
BSR 2014- Department of Buildings
S07- 145
Item Code
BSR 2014- Department of Buildings
S07- 146
Item Code
U147U148U149U150U151
U152U153U154U155U156
U157U158U159U160U161
U162U163U164U165U166
BSR 2014- Department of Buildings
S07- 147
Item Code
U167U168U169U170U171
U172U173U174U175U176
U177U178U179U180U181
BSR 2014- Department of Buildings
S07- 148
Item Code
U182U183U184U185U186
U187U188U189U190U191
U192U193U194U195U196
BSR 2014- Department of Buildings
S07- 149
Item Code
U197U198U199U200U201
BSR 2014- Department of Buildings
S07- 150
Item Code
U202U203U204U205U206
U207U208U209U210U211
U212U213U214U215U216
BSR 2014- Department of Buildings
S07- 151
Item Code
U217U218U219U220U221
U222U223U224U225U226
U227U228U229U230U231
BSR 2014- Department of Buildings
S07- 152
Item Code
U232U233U234U235U236
U237U238U239U240U241
U242U243U244U245U246
BSR 2014- Department of Buildings
S07- 153
Item Code
U247U248U249U250U251
BSR 2014- Department of Buildings
S07- 154
Item Code
U252U253U254U255U256
U257U258U259U260U261
U262U263U264U265U266
BSR 2014- Department of Buildings
S07- 155
Item Code
U267U268U269U270U271
U272U273U274U275U276
U277U278U279U280U281
BSR 2014- Department of Buildings
S07- 156
Item Code
U282U283U284U285U286
U287U288U289U290U291
U292U293U294U295U296
BSR 2014- Department of Buildings
S07- 157
Item Code
U297U298U299U300U301
U302U303U304U305U306
U307U308U309U310U311
BSR 2014- Department of Buildings
S07- 158
Item Code
U312U313U314U315U316
U317U318U319U320U321
U322U323U324U325U326
U327U328U329U330U331
U332U333U334U335U336
U337
BSR 2014- Department of Buildings
S07- 159
Item Code
U338U339U340U341
U342U343U344U345U346
U347U348U349U350U351
U352U353U354U355U356
U357U358U359U360U361
U362U363U364U365U366
U367U368U369U370U371
BSR 2014- Department of Buildings
S07- 160
Item Code
U372U373U374U375U376
U377U378U379U380U381
U382U383U384U385U386
U387U388U389U390U391
U392U393U394U395U396
U397U398U399
BSR 2014- Department of Buildings
S07- 161
Item Code
U400U401
U402U403U404U405U406
U407U408U409U410U411
U412U413U414U415U416
U417U418U419U420U421
U422U423U424U425U426
U427U428U429U430U431
BSR 2014- Department of Buildings
S07- 162
Item Code
U432U433U434U435U436
U437U438U439U440U441
U442U443U444U445U446
U447U448U449U450U451
U452U453U454U455U456
U457U458U459U460U461
U462U463U464U465
BSR 2014- Department of Buildings
S07- 163
Item Code
U466
U467U468U469U470U471
U472U473U474U475U476
U477U478U479U480U481
U482U483U484U485U486
U487U488U489U490U491
U492U493
BSR 2014- Department of Buildings
S07- 164
Item Code
U494U495U496
U497U498U499U500U501
U502U503U504U505U506
U507U508U509U510U511
U512U513U514U515U516
U517U518U519U520U521
U522U523U524U525U526
BSR 2014- Department of Buildings
S07- 165
Item Code
U527U528U529U530U531
U532U533U534U535U536
U537U538U539U540U541
U542U543U544U545U546
U547U548U549U550U551
U552U553U554
BSR 2014- Department of Buildings
S07- 166
Item Code
U555U556
U557U558U559U560U561
U562U563U564U565U566
U567U568U569U570U571
U572U573U574U575U576
U577U578U579U580U581
U582U583U584U585U586
BSR 2014- Department of Buildings
S07- 167
Item Code
U587U588U589U590U591
U592U593U594U595U596
U597U598U599U600U601
U602U603U604U605U606
U607U608U609U610U611
U612U613U614U615U616
U617U618U619U620
BSR 2014- Department of Buildings
S07- 168
Item Code
U621
U622U623U624U625U626
U627U628U629U630U631
BSR 2014- Department of Buildings
S07- 169
Item Code
U632U633U634U635U636
U637U638U639U640U641
U642U643U644U645U646
U647U648U649U650U651
BSR 2014- Department of Buildings
S07- 170
Item Code
U652U653U654U655U656
U657U658U659U660U661
U662U663U664U665U666
BSR 2014- Department of Buildings
S07- 171
Item Code
U667U668U669U670U671
U672U673U674U675U676
U677U678U679U680U681
BSR 2014- Department of Buildings
S07- 172
Item Code
U682U683U684U685U686
U687U688U689U690U691
U692U693U694U695U696
BSR 2014- Department of Buildings
S07- 173
Item Code
U697U698U699U700U701
U702U703U704U705U706
U707U708U709U710U711
BSR 2014- Department of Buildings
S07- 174
Item Code
U712U713U714U715U716
U717U718U719U720U721
U722U723U724
BSR 2014- Department of Buildings
S07- 175
Item Code
U725U726
U727U728U729U730U731
U732U733U734U735U736
U737U738U739
BSR 2014- Department of Buildings
S07- 176
Item Code
U740U741
BSR 2014- Department of Buildings
S07- 177
Item Code
U742
U743
U744
U745
U746
U747
U748
U749
U750
U751
U752
U753
BSR 2014- Department of Buildings
S07- 178
Item Code
U754
U755
BSR 2014- Department of Buildings
S07- 179
Item Code
U756
U757
U758
U759
U760
U761
U762
U763
U764
U765
U766
U767
BSR 2014- Department of Buildings
S07- 180
Item Code
U768
U769
U770
U771
U772
U773
BSR 2014- Department of Buildings
S07- 181
Item Code
U774
U775
U776
U777
U778
U779
BSR 2014- Department of Buildings
S07- 182
Item Code
U780
U781
U782U783U784U785U786
U787U788U789U790U791
U792
BSR 2014- Department of Buildings
S07- 183
Item Code
U793U794U795U796
BSR 2014- Department of Buildings
S07- 184
Maintenance BSR for 2014Department of Buildings, Sethsiripaya, Battaramulla.
Imperial Units
Description
A-DEMOLISHER
Demolishing brickwork in cement stacking brick and clearing debris away Cube
Demolishing brickwork in lime stacking brick and clearing debris away CubeDemolishing cabook masonry in lime mortar stacking cabook and clearing debris away
Cube
Dismantling cadjan roofing or walling stacking timber and clearing debris Sqr
Removing existing Ceiling, stacking materials and clearing debris SqrDemolishing Cement concrete , and clearing debris in 6" floors Cube
Sqr
Sqr
Sqr
SqrRemoving and stacking Door or Window, size up to 40 Sq.ft: from existing walls
NosRemoving and stacking Door or Window, size over 40 sq.ft from existing walls
NosRemoving and stacking Door or Window, sash only up to 40 Sq.ft: from existing walls
NosRemoving and stacking Door or Window, sash only over 40 sq.ft: from existing walls
NosRemoving and stacking Down pipes, 4" to 6" dia: G.I. old or decayed, from existing building
L.ftDemolishing drains and clearing debris L.ftRemoving and stacking Expanded Metal from existing frames sq.ft
L.ftDemolishing floors brick paved, and clearing debris away Sqr
NosRemoving and stacking Glass panes in doors and windows and fanlights sq.ft
Removing and stacking Gutter, eaves, from roofs of single storeyed buildings L.ft
Removing and stacking gutter, eaves, from roofs of 2 storeyed buildings L.ft
Item Unit
Demolishing reinforced cement concrete in suspended floors of 4" thick, removing reinforcement and clearing debris
Removing and stacking corrugated sheets, iron, asbestos or Aluminium alloy from roof , or walls
Removing and stacking corrugated sheets, iron asbestos or Aluminium alloy from roofs or walls of two storied buildings
Removing and stacking Corrugated sheets, iron, asbestos or Aluminium alloy from roofs or walls of three storeyed buildings
Uprooting fence , rolling up and stacking barbed wire and all other materials . (Length of fencing to be measured)
Removing and stacking gate sash after demolishing cement concrete blocks or removing posts and separating pintols (Demolishing brickwork where necessary paid for separately).
Author: Eng. D.N.Ranaweera
BSR 2014- Department of Buildings
S07- 185
Description Item Unit
Removing and stacking gutter, eaves, from roofs of three storeyed buildings L.ft
Removing and stacking partitions at site including making good to walls and floorssq.ft
Chipping lime plastering Chipping lime plastering and clearing debris away SqrChipping rendering, cement, and clearing debris away from brick walls and floors
SqrChipping rendering, cement, and clearing debris away from cement concrete floors and walls
SqrRoof removing
Sqr
Sqr
SqrDemolishing rubbleDemolishing rubble masonry in cement, stacking rubble and clearing debris
CubeDemolishing rubble masonry in lime, stacking rubble and clearing debris CubeDemolishing tiles, glazed and clearing debris SqrRemoving and stacking tilesRemoving and stacking tiles Calicut or half round, from roof of single storeyed buildings
SqrRemoving and stacking tiles Calicut or half round, from roof of 2 storeyed buildings
SqrRemoving and stacking tiles Calicut or half round, from roofs of three storeyed buildings
SqrRemoving water proof, asbestos ceiling &Valance or Barge boards.
Removing waterproof Treatment or hot bitumen from flat roof and clearing debris awaySqr
Sqr
Sqr
L.ft
L.ftChipping cement plasterChipping cement plaster, soffit and clearing debris away SqrTransporting debrisTransporting debris cleared away from site by tractor (app10 miles away )
Load
Roof removing tiles and timber, stacking serviceable materials and clearing debris in single storeyed buildings
Roof removing tiles and timber, stacking serviceable materials and clearing debris in two storeyed buildings
Roof removing tiles and timber, stacking serviceable materials and clearing debris in three storeyed buildings
Removing ceiling asbestos including timber framework, stacking serviceable materials and clearing debris away in single storeyed buildings
Removing ceiling asbestos including timber framework, stacking serviceable materials and clearing debris away in two storeyed buildings
Removing and stacking Valance, Barge board materials and clearing debris away in single storeyed building
Removing and stacking Valance, Barge board materials and clearing debris away in two storeyed building
BSR 2014- Department of Buildings
S07- 186
Description Item Unit
LoadTransporting debris cleared away from site by 3.5 cube capacity heavy vehicle and loading with JCB machine ( app. 10 miles away )
BSR 2014- Department of Buildings
S07- 187
Description Item Unit
Preparatory work
SqrFelling Trees
Nos
Nos
Nos
NosRemoving Top SoilRemoving top soil to a depth not exceeding 6" & depositing as directed within site
Sqr
Clearing site vegetation including removal of bushes, shrub under growth hedges and tree stumps up to 12" girth measured at height up to 3' 0" above ground level ,removing rubbish up to a distance of 150 ft beyond the outer walls of the proposed building.
Removing trees and stumps size of girth varies from 1' 0" and up to 2' 0" and girths are measured at 3' 0" height above ground level including cutting of trunks and branches, grubbing up roots, staking of serviceable materials and disposal of unserviceable materials.( aveg. 6" dia. and aveg. ht 10')
Removing trees and stumps size of girth varies beyond 2' 0"" and up to 4' 0" and girths are measured at 3' 0" height above ground level including cutting of trunks and branches, grubbing up roots, staking of serviceable materials and disposal of unserviceable materials. ( aveg. 12" dia. and aveg. ht 16' 6")
Removing trees and stumps size of girth varies beyond 4' 0" and up to 8' 0 " and girths are measured at 3' 0" height above ground level including cutting of trunks and branches, grubbing up roots, staking of serviceable materials and disposal of unserviceable materials. ( aveg. 2' 0"dia. and aveg. ht 23' 0")
Removing trees and stumps size of girth varies beyond 8' 0 " and girths are measured at 3' 0" height above ground level including cutting of trunks and branches, grubbing up roots, staking of serviceable materials and disposal of unserviceable materials. ( aveg. 3' 4" dia. and aveg. ht 33' 0")
BSR 2014- Department of Buildings
S07- 188
Description Item Unit
B-EXCAVATOR
Cube
Cube
Cube
Cube
Cube
Cube
CubeBenching rock in foundation in 3"-6" steps.(Blasting not allowed) sq.ft
- Deleted -Backfilling & compacting pits and trenches with available earth . CubeBackfilling & compacting pits and trenches with imported earth. Cube
Sqr
Cube
Cube
Cube
Filling Under floors & foundations
Cube
Cube
Excavation over site to reduce level in any material except rock requiring blasting including depositing and leveling as directed up to a distance not exceeding 30ft
Excavation in trenches for walls/column pits in soft/loose soil from, 0 to 5ft deep and depositing excavated material to a distance not exceeding 30ft . (earth work support to be paid separately).
Excavation in trenches for walls/column pits in ordinary soil from, 0 to 5ft deep and depositing excavated material to a distance not exceeding 30ft . (earth work support to be paid separately).
Excavation in trenches for walls/column pits in hard dense soil from 0 to 5ft deep and depositing excavated material to a distance not exceeding 30ft . (earth work support to be paid separately).
Excavation in trenches for walls/column pits in mud/wet soil from 0 to 5ft deep and depositing excavated material to a distance not exceeding 30ft . (earth work support to be paid separately).
Excavation in trenches for walls/column pits in soft disintegrated rock (not requiring blasting) up to a depth of 5ft and depositing excavated material to a distance not exceeding 30ft . (earth work support to be paid separately).
Excavation in trenches for walls/column pits in hard rock requiring blasting up to a depth of 5ft and depositing excavated material to a distance not exceeding 30ft . (earth work support to be paid separately).
Cutting turf sods loading to hand carts and transporting up to 30 yards laying and watering for 30 days .(Royalty for turf pegging and transport beyond 30 yards paid separately)
Drains, earth, in any soil except rock requiring blasting cut to gradient and shape as directed and depositing soil within site
Excavation for foundation in any material except rock requiring blasting, part return fill in and ram, and disposing surplus within site as directed.(not exceeding 5ft depth)
Excavation & leveling site in any material except rock requiring blasting, including depositing and leveling.
Note:-For excavation beyond the depth of 5' 0" an additional unskilled laborer should be added for every additional depth of 5' 0" or part thereof for each cube of excavation beyond the original 5' 0" depth.
Filling under floors with gravel or other approved quality of filling, spread, water and well rammed in 3" layers with available earth
Filling under floors with gravel or other approved quality of filling, spread, watered and well rammed in 3" layers with imported earth.
BSR 2014- Department of Buildings
S07- 189
Description Item Unit
Sand filling in Column footing, under wall foundations, watered and well rammed.Cube
Earth work supports
sq.ftEarthwork support (close planking) in trenches up to 5ft 0" depth (2" thick class 2 Timber )
sq.ft
sq.ft
Earthwork support (open planking) in trenches up to a depth of 5ft 0" (2" thick class 2 Timber )
Earthwork support (Close planking ) in deep excavation in trenches up to 15ft 0" depth. Consider trench of 15ft 0" width 5ft 0" at top and 3ft 6" at bottom. (2" thick class 2 Timber )(area supported 2/15ft x 15ft) 450 sq.ft
BSR 2014- Department of Buildings
S07- 190
Description Item Unit
C-CONCRETERConcreting Mass (Gr.15 Mix)
Cube
Cube
Cube
Cube
Cube
CubeConcreting Drains (Gr.15 Mix)
L.ft
L.ftConcrete (Grade 20 Mix)
Cube
Cube
L.ft
L.ft
NosCurbs
L.ftConcreting Drains, semi-circular
L.ftConcreting Lintols (Gr. 20 Mix)
L.ft
Mixing and Placing of cement concrete 1:3:6 with 1" metal, hand mixing up to 1 cube, in ground floor. (Shuttering paid for separately)
Mixing and Placing of cement concrete 1:3:6 (1½") using mixer, above one cube, in ground floor. (Shuttering paid for separately)
Mixing and Placing of concrete 1:3:6 with 2" metal, using mixer, above one cube, in ground floor. (Shuttering paid for separately)
Mixing and Placing of cement concrete 1:3:6 (2"), hand mixing up to one cube, in ground floor.(Shuttering paid for separately)
Mixing and Placing of cement concrete 1:2 ½:5 (1") using mixer, above one cube, in ground floor.(Shuttering paid for separately)
Mixing and Placing of cement concrete 1:2 ½:5 (1"), hand mixing up to one cube, in ground floor. (Shuttering paid for separately)
Drains semi-circular in cement concrete 1:3:6(1"), 9" wide and 9" average depth, 3" thick sides and base, inclusive of 1/2" cement rendering 1:3 with necessary expansion joints and excavation(shuttering paid separately), but without ramp.
Drains semi-circular in cement concrete 1:3:6(1") 9" wide and 9" average depth, 3" thick sides and base, inclusive of 1/2" cement rendering 1:3 with necessary expansion joints and excavation(shuttering paid separately),but with 1ft 6" wide ramp .
Cement concrete 1:2:4(3/4") using mixer, above one cube. (R/F and Shuttering paid for separately)
Cement concrete 1:2:4(3/4")using mixer, up to one cube. (R/F and Shuttering paid for separately)
Channels 2" semi-circular, forming in cement concrete floors and 1/2" cement rendering 1:2 (Extra over concrete floors)
Channels 4" semi-circular, forming in cement concrete floors and 1/2" cement rendering 1:2 (Extra over concrete floors)
Supplying & laying corbel stone in cement concrete1:2:4(3/4") reinforced with 4 Nos: 3/8" rods ( shuttering paid separately)
Supplying and laying curb in cement concrete 1:2:4 (3/4") 9" high 3" wide and cement rendered 1/2" thick 1:2.(shuttering excavation paid separately)
Supplying and laying Drains, semi-circular, in cement concrete 1:3:6(1") 9" wide and 9" average depth, with 3" thick sides and base inclusive of 1/2" cement rendering 1:3 expansion joints as necessary, including necessary excavation (Shuttering paid separately)
Lintol, cement concrete 1:2:4(3/4") 4 1/2" x 6" (Reinforcement paid for separately). Rate inclusive of shuttering
BSR 2014- Department of Buildings
S07- 191
Description Item Unit
L.ft
L.ft
L.ft
L.ft
L.ft
L.ftNos
Slabs over drains
sq.ft
Nos
NosSquatting plate for latrines , cement concrete 1:2:4( 3/4'') as per type plan.
NosConcreting of Beams and Columns (Gr. 20 Conc)
Cube
Cube
Cube
Cube
Cube
CubeConcreting Slabs (Gr. 20 Mix)
Sqr
SqrConcreting Structural Elements (Gr. 25 Mix)Cement concrete 1:1½:3(3/4") in ground floor, using mixer and vibrator. Cube
Lintol, cement concrete 1:2:4(3/4") 9" x 6" (Reinforcement paid for separately). Rate inclusive of shuttering
Lintol, cement concrete 1:2:4(3/4") 9" x 9" (Reinforcement paid for separately). Rate inclusive of shuttering
Lintol, cement concrete 1:2:4(3/4") 12" x 9" (Reinforcement paid for separately). Rate inclusive of shuttering
Lintol, cement concrete 1:2:4(3/4") 13 1/2" x 6" (Reinforcement paid for separately). Rate inclusive of shuttering
Lintol, cement concrete 1:2:4(3/4") 13 1/2" x 9" (Reinforcement paid for separately). Rate inclusive of shuttering
Lintol, cement concrete 1:2:4(3/4") 13 1/2" x 12" (Reinforcement paid for separately). Rate inclusive of shuttering
Pad stones in cement concrete 1:2:4(3/4" Metal) precast or in situ.
Slabs over drains ,cement concrete 3" thick 1:2 :4 (3/4) and 1/2" cement rendering 1:2 .(Reinforcement paid for separately ) Rate inclusive of shuttering
Spur stones 8" x 8" x 6" in cement concrete 1:2:4(3/4") for veranda posts supplying and fixing(shuttering paid for separately)
Spur stones 4" x 3" x 2" in cement concrete 1:2:4(3/4") for door posts supplying and fixing(shuttering paid for separately)
Cement concrete 1:2:4(3/4") in column shafts in ground floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)
Cement concrete 1:2:4(3/4") in column shafts in first floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately).
Cement concrete 1:2:4(3/4") in column shafts in second floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately).
Cement concrete 1:2:4(3/4") in beams in ground floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)
Cement concrete 1:2:4(3/4") in beams in first floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)
Cement concrete 1:2:4(3/4") in beams in second floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)
4" thick R.C.C 1:2:4(3/4") in 1st: floor slab using mixer and vibrator. (Reinforcement and shuttering paid for separately)
5" thick R.C.C. in 1st: floor slab using mixer and vibrator. (Reinforcement and shuttering paid for separately)
BSR 2014- Department of Buildings
S07- 192
Description Item Unit
Cube
Cube
Cube
Cube
Cube
CubeReady mixed Concrete
- Deleted - - Deleted - - Deleted -
Form work (Untreated Non-structural Category A)
Sqr
sq.ft
sq.ftForm work (Using Timber planks)
sq.ft
sq.ftPlywood form work (20mm tk.)
sq.ft
sq.ft
Cement concrete 1:1½:3(3/4") in column shafts in ground floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)
Cement concrete 1:1½:3(3/4") in column shafts in first floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately).
Cement concrete 1:1½:3(3/4") in column shafts in second floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately).
Cement concrete 1:1½:3(3/4") in beams in ground floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)
Cement concrete 1:1½:3(3/4") in beams in first floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)
Cement concrete 1:1½:3(3/4") in beams in second floor, using mixer and vibrator. (Reinforcement, shuttering and finishes paid for separately)
Shuttering for floor slab concrete including 4" x 2" (untreated non-structural category A) timber joists and necessary props. up to 12ft height. (Rate to include for dismantling same when required).
Shuttering for column shaft 9" x 9" including (untreated non-structural category A) timber joists and necessary props etc. (Rate to include for dismantling same when required)
Shuttering for beam sides & soffit in (untreated non-structural category B) timber, joists and necessary props etc. (Rate to include for dismantling same when required)
Form work with (untreated non-structural category B) timber planks for column shafts 9" x 9" including (untreated non-structural category B) timber joists and necessary props etc. Rate to include for dismantling same when required.
Form work with (untreated non-structural category B) timber planks for beam sides soffits including (untreated non-structural category B) timber props etc. (Rate to include for dismantling same when required).
Supplying and fixing of 3/4" or (20mm) thick plywood form work for concrete beams in ground floor, including (untreated non-structural category B) timber planks , Battens & Joists for beam sides, soffits etc. (Rate to include for dismantling the same when required). consider 9"x12" beam to 20ft, long contact area 55sft.
Supplying and fixing 3/4" or (20mm) thick plywood form work in column in ground floor, including (untreated non-structural category B) timber joists and necessary props etc. Rate to include for dismantling same when required. Consider area 15 sq.ft. ( 5ft high 9"x9" col. )
BSR 2014- Department of Buildings
S07- 193
Description Item Unit
sq.ft
Supplying and fixing 3/4" or (20mm) thick plywood timber formwork for underside of fist floor slab, including 4" x 2" (untreated non-structural category B) timber joists and necessary props. up to 12ft height. (Rate to include for dismantling same when required). consider 20 x 10 area - 200sft.
BSR 2014- Department of Buildings
S07- 194
Description Item Unit
D-BRICKLAYERArch, Segmental, Brick in cement 1:3 including centering. CubeBrickwork in (1:5) cement mortar Brickwork in cement mortar (1:5) above 1 cube, in ground floor. CubeBrickwork in cement mortar (1:5) up to 1 cube, in ground floor. (up to first floor level).
Cube
CubeBrickwork 4 1/2" thick in cement mortar 1:5 above 1 square. SqrBrickwork 4 1/2" thick in cement mortar 1:5 up to 1 square. Sqr
Sqr9" thick brick wall cement sand 1:5 in ground floor SqrBrick work 13½ thick in cement sand 1:5 in superstructure in ground floor
SqrBrickwork Wire cut)4½ thick brick wall (wire cut) in cement sand 1:5 in ground floor Sqr9" thick in cement and sand 1:5 with wire cut brick Sqr13½ thick brick wall (wire cut) in cement sand 1:5 in ground floor SqrExtra over for brickwork ,from first floor level to second floor. ( for Item Nos. D002 to D005)
Cube
Cube
SqrExtra over 4 1/2" brickwork , ,above second floor level. ( for Item Nos. D006 to D008)
Sqr
L.ft
L.ft
L.ft
L.ftCornices, brick in cement 1:5 and, cement rendering 1:3 up to 9" projection and 9" depth.
L.ft
sq.ft
L.ft
L.ft
Brickwork in cement mortar 1:5 with bricks available at site including sorting and cleaning bricks.
Brickwork 4 1/2" thick in cement mortar 1:5 with available bricks including sorting and cleaning.
Extra over for brickwork ,from second floor level to third floor. ( for Item Nos. D002 to D005)
Extra over 4 1/2" brickwork ,from first floor level to second floor. ( for Item Nos. D006 to D008)
Coping, brick in cement 1:5, weathering and throating on 4 1/2" walls, cement rendering 1/2" 1:3 complete.
Coping, brick in cement 1:5, weathering and throating on 9" walls, and 1/2" cement rendering 1:3 complete.
Coping, brick in cement 1:5, weathering and throating on 14" walls, cement rendering 1/2" 1:3 complete.
Coping, brick in cement 1:5, weathering and throating on 9" walls, and 1/2" cement rendering 1:3 with available brick.
Door or Window inserting in existing walls including makings, openings and making good to floors and walls (Lintol or Arch, and door or window paid for separately).
Drains, brick in cement (1:5) 9" to 12" average depth, 12" wide and cement rendering 1/2" thick 1:2 finished smooth complete with expansion joints as necessary including excavation. (Apron paid for separately).
Drains, brick in cement 1:5, 6"-9" average depth and 9" wide, cement rendering 1/2", 1:2 finished smooth complete with expansion joints as necessary including excavation (apron paid for separately).
BSR 2014- Department of Buildings
S07- 195
Description Item Unit
L.ft
L.ftVent opening up to 12" height and 6" width forming on existing walls and walls made good.
NosBrickwork in (1:8) cement mortar Brickwork in cement and sand 1:8 in foundation up to D.P.C. CubeBrickwork in cement and sand 1:8 in superstructure in ground floor. CubeBrickwork in cement and sand 1:8 in 1st: floor. CubeBrickwork in cement and sand 1:8 in 2nd: floor. Cube
Drains, scott's pattern, including apron formed of brick masonry in cement mortar 1:5 and 1/2" cement rendered, finished smooth complete with expansion joints as necessary including excavation (apron paid for separately)
Steps, 12" wide and 6" to 9" high masonry or brickwork in cement mortar 1:3, rendering 1/2" cement 1:2 with foundation 6" below ground.
BSR 2014- Department of Buildings
S07- 196
Description Item Unit
E-MASONRandom RubbleRandom Rubble Masonry in cement Mortar 1:5, above 1 cube. CubeRandom Rubble Masonry in cement Mortar 1:5, up to 1 cube. Cube
CubeCellular (Hollow) block masonry
Sqr
Sqr
SqrSolid block masonry
Sqr
Sqr
SqrPaste rubble masonrySupplying & Laying pointed or Paste rubble masonry in cement and sand 1:2 in ground Floor.
Sqr
Random Rubble Masonry in cement mortar 1:5 with available rubble including sorting out and cleaning rubble.
4" thick Cellular (Hollow) block masonry in cement and sand mortar 1:5 in ground floor cavities unfilled. ( size of each block 16"x8"x4") (Min com/st 3.0 N/mm2 )
6" thick Cellular (Hollow) block masonry in cement and sand mortar 1:5 in ground floor, cavities unfilled. ( size of each block 16"x8"x6") (Min com/st 3.0 N/mm2 )
8" thick Cellular (Hollow) block masonry in cement and sand mortar 1:5 in ground floor Cavities unfilled. ( size of each block 16"x8"x8") (Min com/st 3.0 N/mm2 )10'x10' area
4" thick solid block masonry in cement and sand mortar 1:5 in ground floor. ( size of each block 16"x8"x4") 10'x10' area (Min com/st 3.0 N/mm2 )
6" thick solid block masonry in cement and sand mortar 1:5 in ground floor.10'x10' area (size of each block 16"x8"x6") (Min com/st 3.0 N/mm2 )
8" thick solid block masonry in cement and sand mortar 1:5 in ground floor. 10'x10' area ( size of each block 16"x8"x8") (Min com/st 3.0 N/mm2 )
BSR 2014- Department of Buildings
S07- 197
Description Item Unit
F-PAVIORExpansion joints in brick floors, filling with bitumen and sand. L.ft
L.ft
Sqr
Sqr
Sqr
SqrFloors, gravel Floors, gravel 4" thick, spreading, watering and ramming. SqrFloor tiles (Laying only)
--Do-- for, tiles 8" x 8" in size. sq.ft--Do-- for, tiles 12" x 12" in size. sq.ft--Do-- for, tiles 16" x 16" in size. sq.ft--Do-- for, tiles 24" x 24" in size sq.ftTiles- pressedTiles, pressed of approved pattern and colour, supplying and fixing. sq.ft
sq.ftsq.ft
sq.ftsq.ftsq.ft
Floor tiles- Porcelain glazed (Non homogeneous)
Expansion joints in concrete floors filling with bitumen and sand (to full depth of concrete and rendering).¼" tk and 4" deep.
Floors, brick paving, 3" thick, set in lime mortar 2:5 and cement rendering 1/2"thick, 1:2 mixture.
Floors, brick paving 3" thick, set in lime mortar 2:5 and cement rendering 1/2" thick, 1:3 with available bricks, including sorting out and cleaning bricks.
Floors, cement concrete 1:2½:5(1" metal) 3" thick cement rendering 1/2", 1:3 with expansion joints filling with cement and sand.
Floors, upper, cement concrete 1:2:4(3/4") 4" thick, cement rendering 1/2", 1:3 with lime putty rendering to soffit and expansion joints filling with cement and sand (Reinforcement paid for separately).
Fixing tiles on floors with all specials, including raking plaster and bedding in cement mortar 1:3 pointed with tile grout to match the tiles. (Tiles supplied by the client or paid separately.**)
Floor tiles- Ceramic Non-skid ( Approved quality) Ceramic ,Non-skid pattern tiles with all specials supplying and fixing to floors including raking plaster and bedding in cement mortar 1:3 and pointed with tile grout to match the tiles. (Quality approved by the Engineer.)
--Do-- for, 8" x 8" in size.( Range of a Tile Price : Rs 50-60) --Do-- for, 12"x12" in size. ( Range of a Tile Price : Rs 135-160)Floor tiles- Ceramic glazed (Non homogenous)-Local Ceramic , glazed, Non homogenous floor tiles with all specials supplying and fixing to floors including raking plaster bedding with cement mortar 1:3 and pointed with tile grout to match the tiles. (Rocell or equivalent brand)
--Do-- for, 8" x 8" in size. ( Range of a Tile Price : Rs 71-83) --Do-- for, 12" x 12" in size. ( Range of a Tile Price : Rs 130-150) --Do-- for, 16" x 16" in size. (, Range of a Tile Price : Rs 240-288)
Porcelain, glazed, Non homogenous floor tiles with all specials supplying and fixing to floors including raking plaster and bedding in cement mortar 1:3. and pointed with tile grout to match the tiles. ( Rocell or equivalent brand)
BSR 2014- Department of Buildings
S07- 198
Description Item Unit
sq.ftsq.ftsq.ftsq.ft
Floor tiles- Vitreous Porcelain ( Homogenous)-Local
sq.ftsq.ftsq.ft
Floor tiles- Polished Porcelain ( Homogenous)-Local
sq.ftsq.ftsq.ft
Floor tiles- Rustic Type ( Homogenous)-Local
sq.ftsq.ft
Floor tiles- (Approved quality)
sq.ft
sq.ft
sq.ft
sq.ft
sq.ftTerrazzo tile flooringTerrazzo tile flooring supplying and laying. Sqr
sq.ftTerracotta tiles
--Do-- for, 18" x 18" in size. ( Range of a Tile Price : Rs 370-398) --Do-- for, 24" x 24" in size.( Range of a Tile Price : Rs774-1375 ) --Do-- for, 24" x 12" in size. (Range of a Tile Price : Rs 387-497) --Do-- for, 24" x 16" in size. (Range of a Tile Price :Rs 547-674)
Porcelain ( glazed/Matt) Homogenous Vitreous, floor tiles with all specials supplying and fixing to floors including raking plaster and bedding in cement mortar 1:3 and pointed with tile grout to match the tiles. ( Rocell or equivalent brand)
--Do-- for, 8" x 8" in size. ( Range of a Tile Price : Rs 70-80) --Do-- for, 12" x12" in size. ( Range of a Tile Price : Rs 160-170) --Do-- for, 16" x16" in size. ( Range of a Tile Price : Rs 260-280)
Porcelain Polished Homogenous, floor tiles with all specials supplying and fixing to floors including raking plaster and bedding in cement mortar 1:3 and pointed with tile grout to match the tiles. ( Rocell or equivalent brand)
--Do-- for, 8" x 8" in size.( Range of a Tile Price : Rs 110--130) --Do-- for, 12" x 12" in size. ( Range of a Tile Price : Rs 290-300) --Do-- for, 24" x 24" in size. ( Tile Price : Rs 1465 )
Floor tiles- Rustic Type ( Homogenous), with all specials supplying and fixing to floors including raking plaster and bedding in cement mortar 1:3 and pointed with tile grout to match the tiles. ( Rocell or equivalent brand)
--Do-- for, 12" x 12" in size. ( Range of a Tile Price : Rs 160-170) --Do-- for,16" x 16" in size. ( Range of a Tile Price : Rs 293-343)
Vitreous ceramic floor tiles, supplying and laying on floor including raking plaster bedding with cement mortar 1:3 and pointed with tile grout to match the tiles. (Quality approved by the Engineer.)
--Do-- for, 12" x 12" in size. solid colour ( matt/ glazed ) Range of a Tile Price around : Rs 125
--Do-- for, 12" x 12" in size, rustic , decorative , heavy duty tiles ( colour ) Range of a Tile Price around : Rs 145
--Do-- for, 12" x 12" in size, step floor tiles 12"x12" Range of a Tile Price around : Rs 180
--Do-- for, 16"x16" in size, solid colour ( matt /glazed ) Range of a Tile Price around : Rs 275
--Do-- for, 24"x24" in size, solid colour ( heavy duty , matt or glazed ) Range of a Tile Price around : Rs 560
Terrazzo, wall lining with precast walling slabs 1 1/2" thick supplying and fixing to complete.
BSR 2014- Department of Buildings
S07- 199
Description Item Unit
sq.ftTiles terracotta 8" x 8" of approved tiles , supply and fixed to floors including racking plaster bedding in cement mortar 1:3 .
BSR 2014- Department of Buildings
S07- 200
Description Item Unit
Wall tiles -glazed ( Approved Quality)
--Do-- for, Coloured tiles 4" x 4" in size. sq.ft--Do-- for, white tiles 4" x 4" in size. sq.ft--Do-- for, Coloured tiles 6" x 6 in size. sq.ft--Do-- for, white tiles 6" x 6" in size. sq.ft
sq.ft--Do-- for, white tiles 8"x10" in size. sq.ft--Do-- for, colour tiles 8"x10" in size. sq.ft--Do-- for, white tiles 8"x12" in size. sq.ft--Do-- for, colour tiles 8"x12" in size. sq.ft
sq.ft
sq.ft
sq.ft
sq.ft
sq.ft
sq.ft
Wall tiles (Fixing only)
--Do-- for size up to 8 "x16". sq.ft--Do-- for size up to 12 "x24". sq.ftBorder Tiles for Wall (Decorative)
L.ft
L.ft
Tiles, glazed with all specials, supplying and fixing to walls including raking plaster and backing in cement mortar 1:3.
--Do-- for available Tiles, (Tiles supplied by the client or paid separately.**)
Wall tiles -LocalTiles glazed with all specials , supplying and fixing to walls including raking plaster backing in cement mortar 1:3 and pointed with tile grout to match the tiles.(Lanka wall Tiles or equivalent brand)
--Do-- for Coloured, white or printed 4 1/2 "x4 1/2"(Range of a Tile Price : Rs 13--17)
--Do-- for Coloured, white or printed 8 "x8" (Range of a Tile Price : Rs 60--68)
--Do-- for Coloured, white or printed 8 "x12" (Range of a Tile Price : Rs 60--68)
--Do-- for Coloured, white or printed 8 "x16" (Range of a Tile Price : Rs 118--128)
--Do-- for Coloured, white or printed 12 "x16" (Range of a Tile Price : Rs 216-242)
--Do-- for Coloured, white or printed 12 "x24"( Range of a Tile Price : Rs 346-410)
Fixing tiles on walls with all specials , including raking plaster backing in cement mortar 1:3 and pointed with tile grout to match the tiles. (Tiles supplied by the client or paid separately.**)
Boarder tiles glazed colour 8"X3", with decorative patterns , supplying and fixing to walls including raking plaster backing in cement mortar 1:3 and pointed with tile grout to match the tiles.(Lanka wall Tiles or equivalent, Range of a Tile Price : Rs80-149)
Boarder tiles glazed colour 8"X3", with decorative patterns , supplying and fixing to walls including raking plaster backing in cement mortar 1:3 and pointed with tile grout to match the tiles.(Lanka wall Tiles or equivalent, Range of a Tile Price Rs150-218)
BSR 2014- Department of Buildings
S07- 201
Description Item Unit
L.ft
L.ft
sq.ft
sq.ft
L.ftGlass block
sq.ftPVC carpeting Supplying and laying PVC carpeting with necessary adhesive etc. sq.ftVinyl Flooring
sq.ft
sq.ftLoop pile carpeting
sq.ftCut pile carpeting - Deleted -
sq.ftInterlocking paving
sq.ft
Boarder tiles glazed colour 12"X3", with decorative patterns , supplying and fixing to walls including raking plaster backing in cement mortar 1:3 and pointed with tile grout to match the tiles.(Lanka wall Tiles or equivalent, Range of a Tile Price : Rs155-231)
Boarder tiles glazed colour 12"X3", with decorative patterns , supplying and fixing to walls including raking plaster backing in cement mortar 1:3 and pointed with tile grout to match the tiles.(Lanka wall Tiles or equivalent, Range of a Tile Price : Rs232-307)
Granite flooring-LocalGranite floor tiles 12" x 12"x1/2" (Local) supplying and fixing to floors including raking plaster bedding with cement mortar 1:3. (Tile Price : Rs 750 )
Granite floor tiles 24" x 12"x3/4" (Local) supplying and fixing to floors including raking plaster bedding with cement mortar 1:3. (Tile Price : Rs 2700)
Labour cost for fixing 12" x 4"x1/2" Granite skirting to bottom line of walls including cutting ,rounding & Forming edges polishing etc.
Glass block 8" x 8" with all specials supplying and fixing to walls including raking plaster and bedding in cement mortar 1:3.
Supplying and laying 2mm thick Vinyl Flooring with necessary adhesive etc. (Mipolam 150 or equivalent)
Supplying and laying 2mm thick Vinyl Flooring with necessary adhesive etc. (Mactile - Gerflor or equivalent)
Supplying and laying Loop pile carpeting with 5mm thick with Mcfoam under layer , firmly bonded to the existing floor. Carpet having primary & Secondary backings, namely polypropylene & Classic back respectively. And having the minimum pile weight of 20 Oz-USA per sq.yard. & loop density of 6,100 Oz/Cu.yard. (Neyland II or equivalent)
Supplying and laying 1/8 gauged, Wide Open Cut pile carpeting (USA or equivalent) with 5mm thick with Mac Form under layer , firmly bonded to the existing floor. Carpet having primary & Secondary backings, namely woven polypropylene & Classic back polypropylene, respectively. And having the minimum pile weight of 30 Oz per sq.yard. & loop density of 5320 Oz/Cu.yard.
Supplying and Laying 80mm thick "Uni" type Coloured interlocking paving blocks having Compressive Strength of 40N/mm2, layed on plain improved sub surface. Rate inclusive for Quarry dust bedding
BSR 2014- Department of Buildings
S07- 202
Description Item Unit
sq.ftPaving tile Slabs
sq.ft
sq.ft
Supplying and Laying 80mm thick "Uni" type Natural cement colour interlocking paving blocks having Compressive Strength of 40N/mm2, layed on plain improved sub surface. Rate inclusive for Quarry dust bedding.
Supplying and Laying 300 x300 x50mm thick Non Reinforced, Natural cement colour, Concrete paving Slab, layed on plain improved sub surface. Rate inclusive for Quarry dust bedding.
Supplying and Laying 300 x300 x50mm thick Reinforced, Natural cement colour, Concrete paving Slab, layed on plain improved sub surface. Rate inclusive for Quarry dust bedding.
BSR 2014- Department of Buildings
S07- 203
Description Item Unit
G-ROOFERCorrugated sheets
SqrCorrugated Aluminium sheets
Sqr
Sqr
SqrCorrugated Asbestos Sheets
Sqr
Sqr
SqrCorrugated Asbestos "Colorup" Sheets
SqrZinc Aluminium Sheet Roofing
sq.ftCorrugated galvanized iron Sheet Roofing
Sqr
Sqr
SqrLeaks -on roofs
Corrugated sheets, iron, asbestos or Aluminium alloy fixed with hook bolts and nuts to roofing or walling, (Corrugated sheets available).
Corrugated Aluminium sheets 24 B.W.G roofing on (Group3,Category A) timber purlins supplied and fixed with Aluminium hooks and nuts or Aluminium drive screws including limpet washers etc.: complete with Aluminium ridging, including treating timber with wood preservative
Corrugated Aluminium sheet walling 24 B.W.G on 4" x 2" (Group3,Category A) timber framework, sheets to have 4" end lap and 1" corrugation side lap. (Wall plate measured separately).
Corrugated Aluminium sheets 24 B.W.G supplied and fixed to roof or wall (on existing framework) with hook bolts or drive screws etc.: Sheets to have 4" end lap and 1" corrugation side lap. (Wall plate measured separately).
Corrugated asbestos (Mascons or equivalent.) sheet roofing on (Group3,Category A) timber purlins supplied and fixed complete including treating timber with wood preservative (Ridging measured separately).
Corrugated asbestos (Mascons or equivalent.) sheet walling on 4"x2" (Group3,Category A) timber framework supplied and fixed complete.
Corrugated asbestos sheets supplied and fixed to roof or wall on existing framework with necessary coach screws and limpet washers or hook bolts.
Corrugated asbestos "Colorup" Sheets supplied and fixed to roof or wall on existing framework with necessary coach screws and limpet washers or hook bolts.
Supplying and fixing Zinc Aluminium roofing sheets (0.47 gauge)on existing frame work using nut & bolt / self tapping screws or fasteners. (Rhino Supermet or Equivalent.)
Corrugated galvanized iron Roofing 24 B.W.G on (Group3,Category A) timber purlins supplied and fixed complete with G.I ridging, washers, hook bolts or clips including treating timber with wood preservative. (Sheets to have 6" end laps and 1ft 1/2" corrugation side
Supplying and fixing 22 B.W.G Corrugated G.I walling on (Group3,Category A) timber framework
Corrugated G.I sheets 24 B.W.G supplied and fixed to roof, wall or fence with necessary cup washers and hook bolts and screws. (Timber framework paid for separately).
BSR 2014- Department of Buildings
S07- 204
Description Item Unit
Leaks (up to 5 in number) in Tiled roofs of single storeyed buildings made good. Nos
Leaks (above 5 in number) in roofs of single storeyed buildings made good.Nos
Leaks (Up to 5 in number) in roofs of buildings above one story made good).Nos
Leaks (above 5 in number) in roofs of buildings above one story made good).Nos
Leaks in corrugated sheet roofs made good with bitumen washers and G.I bolts and nuts.Nos
NosRidging
L.ftRidging, Calicut pattern, bedded in cement and lime mortar 1:1:4, Coloured to match tiles.
L.ft
L.ft
L.ft
L.ft
L.ft
L.ft
L.ftZinc Aluminium ridge capping
L.ft
L.ftSkylight glass
NosTiles, Calicut pattern, flat
Nos
Leaks in corrugated sheet roofs patched with jute hesseain dipped in Asphalt and laid over with cement and sand layer above.
Ridging, asbestos cement, Aluminium alloy, or G.I available, fixed with hook bolts or screws.
Ridging, Calicut pattern bedded in cement and lime mortar 1:1:4, Coloured to match tiles, (Tiles available at site).
Ridging, Galvanized iron 24 B.W.G 18" wide overall supplied and fixed complete.
Ridging with asbestos cement close fitting ridges (Mascons or equivalent.) supplied and fixed complete with roofing screws or hook bolts.
Ridging, half round tiles, bedded in lime, cement mortar 1:1:4 and Coloured to match tiles.
Ridging with half round tiles bedded in lime cement mortar 1:1:4 and Coloured to match tiles (Tiles available at site).
Ridging, half round or Calicut pattern removed and re-laid in cement lime mortar 1:1:4 and Coloured to match tile.
Supplying and fixing Zinc Aluminium ridge capping (width 914mm ) 0.47 gauge, to existing sheet roof, using new fasteners or st /screws. (Rhino Supermet or Equivalent.)
Supplying and fixing Zinc Aluminium ridge capping(457mm girth) ( .47 gauge ) , to existing sheet roof, using new fasteners or st /screws. (Rhino Supermet or Equivalent.)
Skylight glass 2ft 0"x2ft 0", 1/4" thick ribbed, supplied & fixed to roof including necessary lime cement filleting.
Note: Refer Item numbers From H100 & H101 for Roofs with Calicut pattern tiles on (Group3, Category A) sawn timber framework
Tiles, Calicut pattern, flat, supplied and laid up to 5 tiles in single storeyed buildings.
BSR 2014- Department of Buildings
S07- 205
Description Item Unit
NosTiles, Calicut pattern, flat, supplied and laid up to 5 Tiles in buildings of more than one story.
Nos
NosTiles Calicut pattern, supplied and laid in any building. SqrTiles Calicut pattern laid in any building (tiles available at site). SqrTiles Calicut pattern, ventilator, supplied and laid in single storeyed building.
NosTiles Calicut pattern, ventilator, supplied and laid in buildings of over one story.
Nos
NosNos
Tiles half round
Tiles half round supplied and laid, up to 50, in single storeyed buildings. NosTiles half round supplied and laid, above 50 and up to 100 in single storeyed buildings.
NosTiles, half round, supplied and laid up to 50 on buildings of more than one story.
Nos
NosTiles half round, supplied and laid in any building. SqrTiles, half round, laid in any building (Tiles available at site) SqrShifting and re-laying half round tiles. Sqr
SqrSupplying and laying half round tiles on the existing asbestos roof. SqrStructural Steel Purlins for Roof
--Do-- for (weight 6.7 Kg/m) & 76x38mm size "C" channel purlin L.ft--Do-- for (weight 10.42 Kg/m) & 102x51mm size "C" channel purlin L.ft--Do-- for (weight 14.9 Kg/m) & 127x64mm size "C" channel purlin, L.ft--Do-- for (weight 17.88Kg/m) & 152x76mm size "C" channel purlin, L.ftHigh tensile Galvanized steel, C-channel purlins for Roof
--Do-- with the sectional dimensions of "C" channel , 100mmx50mmx15mmL.ft
Tiles, Calicut pattern, flat, supplied and laid (above 5 and up to 25) in Single Storeyed buildings.
Tiles, Calicut pattern, flat, supplied and laid above 5 and up to 25 in buildings of more than one story.
Tiles, Fiber glass, laid in small quantities including fixing with G.I wire where necessary (tiles available at site)
Tiles, Fiber glass, Calicut pattern, supplied and fixed.
Note: Refer Item numbers From H102 & H103 for Roofs with Half round tiles on (Group3, Category A) sawn timber framework
Tiles, half round above 50 and up to 100 in number supplied and laid on roof of buildings of more than one story.
Shifting and re-laying Calicut pattern tiles.
Supplying & Fixing Structural & High Tensile Steel "C"" channel purlin, together with 75mmx75mmx6mm L-Iron cleats on roof truss with 10mm dia. Bolt and nuts. (Painting Paid for separately)
Supplying & Fixing High tensile Galvanized Steel "C" channel purlins, having the member thickness of 2.0mm (Tensile strength 450 N/mm2) standards complying with JISG 3302. Each Purlins connected with 75mmx75mmx6mm L-Iron cleats on roof truss together with 10mm dia. Bolt and nuts. (Painting is not considered)
BSR 2014- Department of Buildings
S07- 206
Description Item Unit
--Do-- with the sectional dimensions of "C" channel , 150mmx65mmx20mm L.ft
Heat and Sound installation (Double side luminary Aluminium foil)
sq.ftTimber Members for Roofing Note:- Please find Timber Reepers from Item No H095 to H099
L.ftSupply and fixing 4''x2'' (Group3,Category A) timber rafters for roof work.
L.ftSupply and fixing 7''x2'' (Group3,Category A) timber ridge plate in roof work.
L.ftSupply and fixing 4''x3'' (Group3,Category A) timber wall plate in roof work.
L.ftSupply and fixing 5''x3'' (Group3,Category A) timber purlin in roof work.
L.ft
L.ft
1/2" thick heat and sound installation sheet laying on 3"x3" GI mesh existing steel purlin and fixing with binding
Supply and fixing 2''x2'' (Group3,Category A) timber Battons in roof work, with nails over 100' 0"
Supply and fixing 4''x3'' (Group3,Category A) timber Struts, up to 6' height in roof structure, including forming necessary Timber joints at both ends. 2' Timber bearer provided at Bottom.
BSR 2014- Department of Buildings
S07- 207
Description Item Unit
H-CARPENTER & JOINER
L.ft
L.ft
L.ft
L.ft
L.ft
L.ftBoards, barge, valance, fascia
L.ft
L.ft
L.ft
L.ftBoards, barge, valance, fascia, available, fixing including cutting and minor repairs.
sq.ftCeiling / Partition
Sqr
Sqr
Sqr
Sqr
Beading, Burma Teak, 1 1/2" to 2" x1/2" plain chamfering, supplying and fixing complete with brass screws.
Beading, Burma Teak, 1"x 3/4" plain chamfering, supplying and fixing complete with brass screws.
Beading, Alstonia or local timber 1 1/2" to 2"x1/2" plain chamfering, supplying and fixing complete with brass screws.
Beading, Halmilla, 1 1/2" to 2" x 1/2", plain chamfering, supplying and fixing complete with brass screws.
Beading or filleting in Ginisapu or local timber for glass panes supplying and fixing complete with brass springs or brass panel pins.
Beading or filleting on underside of ceiling removing and re-fixing with brass screws complete.
Boards, barge, valance, fascia, 9" wide & 1" thick, in (Group 5,Category A), local timber fixing complete with necessary screws new or renewing.(above one Cubic foot)
Boards, barge, valance, fascia, 9" wide & 1" thick, in (Group 5,Category A),local timber supplying and fixing complete with necessary screws new or renewing, up to 1 Cu.ft.
Boards, barge, valance, fascia, 9" wide & 1" thick, in (Group 5,Category B), local timber fixing complete with necessary screws new or renewing.(above one Cubic foot)
Boards, barge, valance, fascia, 9" wide & 1" thick, in (Group 5,Category B),local timber supplying and fixing complete with necessary screws new or renewing, up to 1 Cu.ft.
Ceiling, asbestos (Mascons or equivalent.), flat fixing with clout headed nails to 4" x 2" joists and 2"x2" bearers of (Group 4,Category A) timber, including 1 1/2" x 1/2" cover fillets and 2 1/2" x 1 1/2" coves of Alstonia or equivalent timber. Rate to include 2 coats of wood preservatives to joists and bearers. Primer undercoating and two coats of emulsion paint to Asbestos sheets.
Flat asbestos (Mascons or equivalent.) horizontal eaves ceiling comprising 2" x 2" bearars in (Group 4,Category A) timber, asbestos sheet supplied and fixed with beadings & cove moulding, rate to include for applying wood preservative to timber frame, two coats enamel paint for beadings, and two coats of emulsion paint to ceiling.
Ceiling, asbestos, plywood, available, cut and fixing on existing bearers, rafters or frames (beading or cover fillets paid for separately)
Ceiling or partition, asbestos supplying and fixing with clout headed nails to existing bearers, rafters or frames (Beadings or cove fillets paid for separately)
BSR 2014- Department of Buildings
S07- 208
Description Item Unit
L.ftCeiling, Lunumedella, available at site, fixing with new wire nails. Sqr
Sqr
Sqr
Sqr
Sqr
NosCeiling, upper side cleaning and debris clearing away. Sqr
Sqr
SqrPartitions
sq.ft
sq.ft
sq.ft
sq.ft
Ceiling board, 6" x 5/8" to 3/4", lunumedella, renewing in small quantities rate to include for scaffolding (up to 30 L.ft.)
Ceiling or partition, Lunumedella, 1/2" planed, lapped and nailed to existing frames or underside of rafters, above 1 square (Fillets and beadings paid for separately)
Ceiling or partition, Lunumedella, 1/2"planed, lapped and nailed to existing frames or underside of rafters, up to 1 square (Fillets and beadings paid for separately)
Ceiling or partition, Lunumedella, 1/2" beading and rebating, nailing to underside of existing joists, rafters or frames, above one square (Fillets and beadings, paid for separately)
Ceiling or partition, Lunumedella, 5/8" beading and rebating, nailing to underside of existing joists, rafters or frames, up to one square (Fillets and beadings, paid for separately)
Ceiling openings 2ft 0" x 1ft 6" approx., forming complete with 2" x 2" bearers. (Glass tiles or sheets paid for separately)
Ceiling Lunumedella 1/2" planks, lapped and nailed to framework consisting of finished size with 3 3/4" x 1 3/4" joists and 1 3/4" x 1 3/4" bearers in (Group 4,Category A) timber, Rate to include for 2 coats of wood preservatives to joists and bearers.
Ceiling Lunumedella 3/4" thick planks, lapped and nailed to framework consisting of finished size with 3 3/4" x 1 3/4" joists and 1 3/4" x 1 3/4" bearers in (Group 4,Category A) timber, Rate to include for 2 coats of wood preservatives to joists and bearers.
Partitions paneling 7 ft 0" to 10 ft 0" with 1/2" thick chipboard with finished size 3 3/4" x 1 3/4" and 3 3/4" x 3 3/4" upright fixed at 3ft 0" interval and 4" x 2" as horizontal members in (Group 4,Category A) timber. Rate to include for fixing chipboard to both sides. data 9ft 9"x7ft 0"=6
Partition - paneled with 3/8" chipboard with finished size 3' 3/4"x 1' 3/4"and 3' 3/4"x 3' 3/4" uprights fixing at 3' 0" interval sand 4"x 2" as horizontal members in (Group 4,Category A) timber. Rate to include for fixing chipboard to both sides. data 9ft 9"x7ft 0"=68.25 sq.ft
Partitions glazed 7ft -0" - 10ft -0" height 3/16" thick and paneling 1/2" thick plywood with finished size 3 3/4" x 2 3/4" and 3 3/4" x 3 3/4" upright at 3ft 0" intervals and 4" x 2" as horizontal members in (Group 4,Category A) timber. Rate to include for fixing chipboard to both sides of frame2"x1/2" (Group 4,Category A) timber boarding around glass pane.
Partitions glazed 7ft 0" - 10ft -0" height 3/16" thick and paneling 3/8" thick plywood with finished size 3 3/4" x 2 3/4" upright at 3ft 0" interval and 4" x 2" as horizontal members in (Group 4,Category A) timber. Rate to include for fixing chipboard to both sides of frame 2" x 1/2"
BSR 2014- Department of Buildings
S07- 209
Description Item Unit
Partitions available fixing, including making good to walls and floors. sq.ft
sq.ft
sq.ftTimber Plugs
NosPlywood Panels
sq.ftCove, mouldings
L.ft
L.ftDoors or windows
sq.ft
sq.ft
sq.ft
sq.ft
sq.ft
sq.ft
sq.ft
sq.ft
Partitions, fully paneling, or paneling and glazing 1 1/8" thick with 4" x 2" frames and 1" x 1" quadrant fillets supplying and fixing complete with brass screws in (Group 4,Category A) local timber.
Partitions, glazing and paneling with plywood panels in (Group 4,Category A) timber (main posts 4" x 4" x 10ft 0" intermediate posts 4" x 2" x 7ft 0" approx., and 1 1/2" x 8" capping complete)
Plugs in (Group 4,Category A) timber, 4" long tapering 3" x 2" supplying and fixing to walls in cement mortar 1:3.
Plywood panels, 3 ply, supplying and fixing to existing frames (beadings to be paid for separately)
Cove, mouldings, Halmilla 2 1/2" x 1 1/2" fixing with brass screws and plugs new or renewing.
Cove, mouldings, Alstonia or equivalent 2 1/2" x 1 1/2" fixing with brass screws and plugs new or renewing.
Doors or windows, legging, bracing and battening with groove and tongue joints finished size 3 3/4" x 2 3/4" frames and 3/4" to 7/8" thick sashes in (Group 2,Category A) local timber complete with brass furniture(Rim lock, Hinges).( Door Size 2' 6"x6' 6" = 16¼s.ft)
Doors or windows, legging, bracing and battening with groove and tongue joints finished size 3 3/4" x 2 3/4" frames and 3/4" to 7/8" thick sashes in (Group 2,Category B) local timber complete with brass furniture.( Door Size 2' 6"x6'x 6" = 16¼s.ft)
Doors or windows ledging, bracing and battening, 3/4" to 7/8" thick sash only, in (Group 2,Category A) timber supplying and fixing with available (brass/Iron) furniture.
Doors or windows ledging, bracing and battening, 3/4" to 7/8" thick sash only, in (Group 2,Category B) timber supplying and fixing with available (brass/Iron) furniture.
Doors or windows, framing and battening, with finished size 3 3/4" x 2 3/4" frames and 1" to 1 1/8" sashes in (Group 2,Category A) local timber complete with brass furniture.
Doors or windows, framing and battening, with finished size 3 3/4" x 2 3/4" frames and 1" to 1 1/8" sashes in (Group 2,Category B) local timber complete with brass furniture.
Doors or windows, framing and battening, with finished size 3 3/4" x 2 3/4" frames and 1 1/4" to 1 1/2" sashes in (Group 2,Category A) local timber complete with brass furniture.
Doors or windows, framing and battening, with finished size 3 3/4" x 2 3/4" frames and 1 1/4" to 1 1/2" sashes in (Group 2,Category B) local timber complete with brass furniture.
BSR 2014- Department of Buildings
S07- 210
Description Item Unit
sq.ft
sq.ft
sq.ft
sq.ft
sq.ft
sq.ft
sq.ft
sq.ft
sq.ft
sq.ft
sq.ft
sq.ft
sq.ftDoor or Window, removing, easing and re-fixing. NosDoor or Window, easing only. Nos
L.ft
NosDoor or Window, Glazing bars renewing in (Group 2,Category A) timber.
L.ft
Nos
Doors or Windows, sash only 1" to 1 1/8" thick in (Group 2,Category A) timber supplying and fixing complete with available (brass/Iron)furniture.
Doors or Windows, framing and battening, sash only 1" to 1 1/8" thick in (Group 2,Category B) local timber, supplying and fixing complete with available (brass/Iron)furniture.
Doors or Windows, sash only 1 1/4" thick in (Group 2,Category A) timber supplying and fixing complete with available (brass/Iron)furniture.
Doors or Windows, sash only 1 1/4" to 1 1/2" thick in (Group 2,Category B) local timber supplying and fixing complete with available (brass/Iron) furniture.
Doors for garages, framing and battening in (Group 2,Category A) timber with 5" x 4" frames and 1 1/2" thick sashes supplying and fixing complete with iron pintols and strap hinges.
Doors or Windows, glazing and/or paneling with finished size 3 3/4" x 2 3/4" frames and 1 1/8" to 1 1/4" sashes in (Group 2,Category A) local timber supplying and fixing complete with brass furniture.
Doors or Windows, glazing and/or paneling with finished size 3 3/4" x 2 3/4" frames and 1 1/8" to 1 1/4" sashes in (Group 2,Category B) local timber supplying and fixing complete with brass furniture.
Doors or Windows, glazing and/or paneling, sash only 1 1/8" to 1 1/4" thick in (Group 2,Category A) timber with available (brass/Iron) furniture.
Doors or Windows, glazing and/or paneling, sash only 1 1/8" to 1 1/4" thick in (Group 2,Category B) timber with available (brass/Iron) furniture.
Doors paneling and trellising B.R.C. weld mesh No.32, with 4 3/4" x 2 3/4" frames and 1 1/8" thick sashes in (Group 2,Category A) timber, supplying and fixing complete with brass furniture.
Doors paneling and trellising B.R.C. weld mesh No.32 sash only 1 1/8",supplying and fixing with available (brass/Iron)furniture.
Doors, paneling and trellising/B.R.C. weld mesh No.32 sash only 1 1/4" thick in (Group 2,Category A) timber with available furniture.
Doors paneling with finished size 3 3/4" x 2 3/4" frames and 1 1/8" - 1 1/4" sashes in (Group 2,Category A) timber supplying and fixing complete with available (brass/Iron) furniture.
Door or Window frames renewing in short lengths with (Group 2,Category A) timber. assume 3ft length of door frame renewed. 5' x3'
Door or Window frame altering, existing rebate fillet using (Group 2,Category A) timber with screws and sashes rehung on opposite side.
Door Stops in (Group 2,Category A) timber 1 1/2" x 1 1/2" x 5" tapering, supplying and fixing.
BSR 2014- Department of Buildings
S07- 211
Description Item Unit
Door or Window sashes, available, fixing in position (sash and fittings available at site) Nos
Door sashes swing, removing and re-fixing in new position. Nos
sq.ftDoors, swing 1" thick in (Group 2,Category A) timber with ( ¾") width Ply wood panels supplying and fixing complete with brass gravity hinges.
BSR 2014- Department of Buildings
S07- 212
Description Item Unit
Door frame
L.ft
L.ft
sq.ft
sq.ft
sq.ft
sq.ftDoors or windows framing and battening sash
sq.ft
sq.ft
sq.ftDoors glazing and/or paneling
sq.ft
sq.ft
sq.ft
sq.ftDoor or Window frame
Door frame with finished size 3 3/4" x 2 3/4" in (Group 2,Category A) timber supplying & fixing in position. (data 2' 6"x 6' 6" =16.25s.ft or 16.5' ft long)
Door frame with finished size 3 3/4" x 1 3/4" in (Group 2,Category B) timber supplying and fixing in position. (data 2' 6"x 6' 6" =16.25s.ft or 16.5' ft long)
Plywood Door ** Note:(Brand - GINTOTA or equivalent)Door,1 1/4" thick plywood ordinary finish (Moisture Resistant) single sash, size 2' 9"x6' 9", hung on finished size 3 3/4" x 2 3/4" frame in (Group 2,Category A) timber and complete with brass furniture's. .(Door Lock paid Separately)
Door,1 1/4" thick plywood ordinary finish (Moisture Resistant) single sash, size 2' 9"x6' 9", hung on finished size 3 3/4" x 2 3/4" frame in (Group 2,Category B) timber and complete with brass furniture's. .(Door Lock paid Separately)
Supplying and fixing Door 1¼" thick, plywood, ordinary finish (Moisture Resistant), single sash, size 2' 9"x6' 9",hung to the existing frame including necessary brass fittings.(Door Lock paid Separately) data 2ft 9"x6ft 9"=18.56s.ft
Supplying & fixing ,1 1/4" thick Ply wood door, Both Side Luxury finish (Moisture Resistant) ,size 2' 9"x6' 9", single sash, hung to existing frame including necessary brass fittings.(Door Lock paid Separately) data 2ft 9"x6ft 9"=18.56s.ft
Doors or windows framing and battening finished size with 3 3/4" x 2 3/4" frames and 1 1/4" to 1 1/2" sashes in (Group 7, Category A) local timber complete with brass furniture.
Doors or windows framing and battening sash only 1" to 11/8" thick in (Group 7, Category A) timber supplying and fixing complete with available furniture.
Door or windows framing and battening sash only 1 1/4" to 1 1/2" thick in (Group 7, Category A) local timber supplying and fixing complete with available furniture.
Doors glazing and/or paneling finished size with 3 3/4"x2 3/4" frames and 1 1/8" to 1 1/4" thick sashes in (Group 7, Category A) timber supplying and fixing complete with brass furniture.
Doors glazing and/or paneling sash only 1 1/8" to 1 1/4" thick in (Group 7, Category A) timber special class with available ironmonger.
Windows glazing and paneling finished size with 3 3/ 4" x 2 3/4" frame and 1 1/8" to 1 1/4" thick sash in (Group 7, Category A) local timber supplying and fixing complete with brass furniture.
Windows glazed and paneled, sash only 1 1/8" to 1 1/4" thick in (Group 2, Category A) timber milla with available ironmonger.
BSR 2014- Department of Buildings
S07- 213
Description Item Unit
sq.ft
sq.ftFillets, quadrant Fillets, quadrant 3/4" x 3/4" supplying and fixing with nails, in (Group 6, Category A) timber.
L.ftFillets, quadrant 1" x 1" in (Group 6, Category A) timber supplying and fixing with nails.
L.ftTimber Gate
sq.ft
sq.ft
sq.ft
sq.ft
NosLouver blades
L.ftLouver blades 3/8" minimum thickness in (Group 1, Category A) timber over 4" and up to 6".
L.ftLouver blades 3/8" minimum thickness in (Group 1, Category A) timber over 6" and up to 9".
L.ftWooden Posts
L.ft
L.ftPosts, Wooden, round jungle timber 5" minimum and average 6" dia. supplying and fixing.
L.ftReepers, timber
Door frame finished size with 3 3/4" x 2 3/4" in (Group 7, Category A) local timber supplied and fixed in position.
Window frames finished size with 3 3/ 4" x 2 3/4" in (Group 7, Category A) timber supplied and fixed in position.
Gate, 1 3/4" as per type plan for bungalow, 6 1/2" top rail, with 2 3/4" x 3/4" weather capping, 8" lock and bottom rails and styles, splay meeting styles, 2" x 1 1/4" verticals at 3 1/2" centers in groups of 3, panels of 4" x3/4" groove and tongued boards fixed raking, and 1/2" dia. tension bars fixed complete using available fittings.(Group 5, Category A) local timber.
Gate 1 3/4" thick for bungalows, 4" top rails and styles, 8" bottom rails, 3" braces, 1 3/4" x 1 3/4" and 1" x 1 1/4" verticals at 4" centers supplying and fixing complete using available fittings (Group 5, Category A) local timber.
Gate 1 1/2" thick, with 4" top and bottom rails, styles and braces and 2" x 1" laths fixing at 4" centers supplying fixing complete with available furniture (Group 5, Category A) local timber.
Gate 1 3/4" thick with 4" top and bottom rails, styles and braces, and 3/4" bars at 4" centers supplying fixing complete with available fittings (Group 5, Category A) local timber.
Gate sash with gate posts available at site, fixing complete including fixing post (Gate and Posts available).
Louver blades 3/8" minimum thickness in (Group 1, Category A) timber up to 4" width supplying and fixing.
Posts, veranda, 5" x 5" tapering to 4" x 4" in (Group3, Category A) timber, supplying and fixing on spur stones (spur stones paid for separately)
Posts, veranda 6" x 6" tapering to 5" x 5" in (Group3, Category A) timber supplying and fixing on spur stones (spur stones paid for separately)
BSR 2014- Department of Buildings
S07- 214
Description Item Unit
L.ftReepers 2" x 1" in (Group3, Category B) local timber up to 100 L.ft: supplying and fixing.
L.ft
L.ft
L.ftReepers, available fixing with wire nails. L.ftRoof with sawn timber framework & Covering Tiles on it
Sqr
Sqr
Sqr
SqrShelving
sq.ft
sq.ftShelving of the types as per plan no 31638, 17988 removed and r3efixing new possession.
sq.ftSkirting Supplying and fixing Skirting in (Group5, Category A) board 3"x¾" on walls.
L.ft
L.ftOther Carpentry work.
cu.ftTimber, available, sorted out, cut to required sizes and fixing in roof and other carpentry work.
cu.ftcu.ft
cu.ft
cu.ft
Reepers 2" x 1" in (Group3, Category A) timber supplying and fixing new or renewing with iron nails, up to 100 L.ft: (Shifting of tiles to be paid for separately)
Reepers 2" x 1/2" in (Group3, Category A) timber supplying and fixing, new or renewing, with iron nails up to 100 L.ft: (Shifting of tiles to be paid for separately)
Reepers 2" x 1/2" in (Group3, Category A) timber supplying and fixing new or renewing, with iron nails over 100 L.ft:
Roof with Calicut pattern tiles on (Group3, Category A) sawn timber framework complete with ridges, hips etc.
Roof with Calicut pattern tiles on (Group3, Category B) sawn timber framework complete with ridges, hips etc.
Roof with half round tiles on (Group3, Category A) sawn timber framework complete with ridges, hips etc.
Roof with half round tiles on (Group3, Category B) timber framework complete with ridges, hips etc.
Shelving in (Group2, Category A) timber 1" thick on triangular brackets with 2 Nos. Horizontals 1 1/2" x 3/4" and 1 1/2" x 1/2" verticals and struts, and 2" x 1" skirting as per Type Plan 31638, supplying and fixing to walls with plugs. (Shelving area to be measured separately.
Shelving in (Group2, Category A) timber 1" thick framing with 2"x2" uprights and 2" x 2" horizontals and 2" x 1/2" skirting supplying and fixing to wall as per type plan 17988 Shelving area to be measured separately.
Supplying and fixing Skirting in (Group5, Category A) timber boards, 6"x ¾" on walls.
Timber available, sorted out, cut to required sizes and fixing in partitions and frames. per 10 L.ft 4x3 or 4/6 cu.ft
Timber, Milla, fixing or renewing in posts and frames. per .5 cu.ftTimber (Group 4,Category A), (excluding Milla) supplying and fixing new or renewing in partitions and frames, including panels and boards.
Timber (Group 4,Category B) supplying and fixing new or renewing in partitions and frames, including panels and boards.
BSR 2014- Department of Buildings
S07- 215
Description Item Unit
Timber (Group 4,Category A) supplying and fixing new or renewing in, other carpentry work. cu.ft
Timber (Group 4,Category B) supplying and fixing new or renewing in, other carpentry work. cu.ft
Trellis
L.ft
L.ft
L.ft
L.ftTrellis laths 1" x 1" supplying and fixing. L.ftTrellis latches 2" x 1/2" in (Group 2,Category A)timber, renewing. L.ft
sq.ft
sq.ft
sq.ft
Trellis laths 1/2" x 1/2" renewing in (Group 2,Category A) local timber, in quantities (Over 100 L.ft)
Trellis laths 1/2" x 1/2" renewing in (Group 2,Category A) local timber, in quantities ( Up to 100 L.ft)
Trellis laths 1" x 1/2" renewing in (Group 2,Category A) local timber, in quantities over 100 L.ft:
Trellis laths 1" x 1/2" renewing in (Group 2,Category A) local timber, in small quantities up to 100 L.ft:
Trellis partition with 1/2" x 1/2" laths fixing 2" apart diagonally, horizontally or vertically, on 4" x 2" milla timber framing.
Trellis screens with laths 1 3/4" x 3/8" at 1 1/4" distance apart vertically and horizontally in Milla timber frames 1 1/2" x 2 1/2"supplying fixing to walls complete.
Trellis screens with laths 1" x 3/8" at 1 1/4" distance apart vertically and horizontally on Milla frames 3" x 1" supplying and fixing to walls complete.
BSR 2014- Department of Buildings
S07- 216
Description Item Unit
J-IRONMONGERBolts and Nuts, IronBolts and Nuts, iron 1 3/4" x 1/4" with washers fixing complete. NosBolts and Nuts, iron 2 1/2" x 3/8" with washers fixing complete. NosBolts and Nuts, iron 5" x 3/8" with washers supplying and fixing complete.
NosBolts and Nuts, iron 9" x 3/8" with washers supplying and fixing complete.
NosBolts and Nuts, iron 5" x 1/2" with washers supplying and fixing complete.
NosBolts and Nuts, iron 6" x 1/2" with washers supplying and fixing complete.
NosBolts and Nuts, iron 12" x 5/8" with washers fixing complete. NosBolts tower, 3" Iron, heavy quality supplying and fixing with Iron screws. NosBolts tower, 4" Iron, heavy quality supplying and fixing with Iron screws. NosBolts tower, 5" Iron, heavy quality supplying and fixing with Iron screws. NosBolts tower, 6" Iron, heavy quality supplying and fixing with Iron screws. NosBolts tower, 2ft 9" Iron, heavy quality supplying and fixing with Iron screws.
NosIron Brackets
NosWeld mesh
sq.ft
sq.ft
sq.ftCabin HooksCabin Hooks and eyes, 2" Iron, supplying and fixing. setCabin Hooks and eyes, 3" Iron, supplying and fixing. setCabin Hooks and eyes, 6" Iron, supplying and fixing. setCabin Hooks and eyes, 8" Iron, supplying and fixing. setCabin Hooks and eyes, 9" Iron, supplying and fixing. setCasement StaysCasement Stays, Iron 10" heavy quality, supplying and fixing. NosCasement Stays, Iron 12" heavy quality, supplying and fixing. NosChimneyChimney flue pipe available, fixing only. L.ft
Brackets with 1 1/2" x 1/4" flat iron 3ft 6" long (approx.) fish tailed at ends, supplying and fixing to walls and walls made good.
2"x2" Weld mesh No.12, supplying and fixing to existing frames with staples (fillets and beadings to be paid for separately)
2"x2" Weld mesh No.10 supplying and fixing to window frames with 2" x 1/2" (Group 2) timber beadings, and painting weld mesh with 2 coats anti-corrosive paint, and beadings with primer, undercoat and 2 coats enamel paint to approved colour. Rate to include for making openings for bolts, casement stays etc.
2"x2" Weld mesh No.12 supplying and fixing to window frames with 2" x 1/2" (Group 2) timber beading, and painting weld mesh with 2 coats anti-corrosive paint, and beadings with primer, undercoat and 2 coats enamel paint to approved tint Rate to include for making openings for bolts, casement stays etc.
BSR 2014- Department of Buildings
S07- 217
Description Item Unit
Chimney flue pipe 6" dia. making and fixing with G.I sheets 22 B.W.G. L.ft
L.ftCowel G.I 24 B.W.G making and fixing for 6" - 9" flue pipes. NosCowel G.I available, fixing complete for 6" -9" dia. flue pipes. Nos
sq.ft
sq.ft
sq.ftGate, Iron
sq.ftGutter HooksGutter Hooks or brackets 3/4" x 1/8" supplying and fixing complete with Iron screws.
NosHasp and staple
Nos
Nos
NosHinges (Iron)Hinges, butt, 2" iron of approved heavy quality supplying and fixing with iron screws.
pairsHinges, butt, 3" iron of approved quality supplying and fixing with iron screws.
pairsHinges, butt, 4" iron of approved quality supplying and fixing with iron screws.
pairsHinges, butt, 5" iron of approved quality supplying and fixing with iron screws.
pairsHinges supplied by Dept. fixing complete with screws. pairs
Nos
Nos
Nos
Nos
Chimney flue pipe 8"-12" dia making and fixing with G.I sheets 22 B.W.G (Sheets to be supplied by Department)
Expanded metal No.8" B.R.C Fabric supplying and laying as reinforcement in floor and foundation.
Expanded metal, zinc sheet, wire gauge etc. fixing with iron screws to existing frames with fillets or beadings ,fillets or beadings to be paid for separately, and expanded metal, zinc sheet, or wire gauge (available at site / supplied by the client).
Fly proofing, perforated zinc, 1/16" mesh, supplying and fixing to existing frames (fillets to be paid for separately)
Gate, iron, with 1 1/2" x 1 1/2" x 1/4" angle iron framework including bracing and horizontal center member, with 5/8" dia. M.S bars at 6" centers complete with strap hinges, hasp and staples.
Hasp and staple 4" iron, safety type of approved heavy quality, supplying and fixing with iron screws.
Hasp and staple 6" iron, safety type of approved heavy quality, supplying and fixing with iron screws complete.
Hasp and staple 12" x 2" iron, specially made out of 1/4" iron plate and fixing with 1/4" x 2" bolts and nuts complete.
Hinges, strap iron 1 1/2" x 1/4" x 1ft 0" long supplying & fixing with necessary bolts and nuts (excluding pintols)
Hinges, strap iron 2" x 1/4" 3ft 0" long supplying and fixing with necessary bolts and nuts (excluding pintols)
Hinges, double strap, 2 1/2" x 3/8" x 3ft 6" flat iron bent to shape and fixing complete with bolts and nuts as per plan 23097
Hinges, double strap, 2 1/2" x 3/8" x 5ft 6" flat iron bent to shape and fixing complete with bolts and nuts as per plan 23097
BSR 2014- Department of Buildings
S07- 218
Description Item Unit
Hinges T 6" Iron, heavy quality supplying and fixing with iron screws complete. pairs
Hinges, T 7" Iron, heavy quality supplying and fixing with iron screws complete. pairs
Hinges, T 8" Iron, heavy quality supplying and fixing with iron screws complete. pairs
Hinges, T 10" Iron, heavy quality supplying and fixing with iron screws complete. pairs
Hinges, T 12" Iron, heavy quality supplying and fixing with iron screws complete. pairs
Hinges, T 14" Iron, heavy quality supplying and fixing with iron screws complete. pairs
Hinges, spring, Japanese Helical, door supplying and fixing with iron screws complete. Nos
Hinges (Stainless Steel) for Timber Doors
pairs
pairsHoldfastHoldfast 1/8" x 2" x 9" flat iron supplying and fixing complete. per No. Nos
NosLocks (iron)Note: Refer Item numbers From K039 to K058 for (Brass / Quality) Locks
Keys, Iron for door locks making and supplying. NosKeys, Iron for cupboards, making and supplying. NosLocks, available, fixing with screws. NosLocks, repairing and re-fixing. Nos
Nos
Nos
Nos
NosLocks, Bird type supplying and fixing with iron screws complete. NosMild steel rods
cwt
cwt
cwt
Supplying and fixing UNION Butt Hinges, , 102x76x 3mm (thick) 2BB stainless steel, for wooden doors with brass screws.
Supplying and fixing UNION Butt Hinges, , 102x76x 2mm (thick) 2BB stainless steel, for wooden doors with brass screws.
Iron rods supplying by the client, cut to correct lengths, inserted in window frames and painted with 2 coats anti-corrosive paint.
Locks, rim, 4" iron, superior quality, heavy type supplying and fixing with iron screws complete.
Locks, rim, 6" iron, superior quality, heavy type supplying and fixing with iron screws complete.
Locks, Motice, 4" iron, superior quality, heavy type supplying and fixing with iron screws complete.
Locks, Motice, 6" iron, superior quality, heavy type supplying and fixing with iron screws complete.
Mild steel rods in reinforcing lintols, beams, columns and slabs, bending to shape, laying in position and tying with G.I wire as directed.
Mild steel rods in foundation bending to shape, laying in position and tying with G.I wire as directed.
M.S rods available., bending to shape, tying with G.I wire and laying in position as directed in reinforcing lintols beams and floors.
BSR 2014- Department of Buildings
S07- 219
Description Item Unit
cwt
L.ft
L.ft
NosRag Bolts 4" x 5/8" with nuts and washers supplying and fixing complete. Nos
sq.ftWire meshWire netting, hexagonal mesh 1/2" supplying and fixing (beading to be paid for separately)
sq.ft
sq.ft
sq.ft
sq.ft Reinforcement, with Tor steel rods
cwt
cwtChain-link fencingNote: Refer Item numbers From S011 to S024 for Barbed wire fencing
L.ft
sq.ft
sq.ft
L.ftMild Steel Grill work
M.S rods available, bending to shape, tying with G.I wire and laying in position as directed reinforcing foundations.
M.S bars 5/8" dia. supplying and fixing in window frames at 4" centers and painted with two coats Aluminium or anti- corrosive paint.
M.S bars 3/4" dia. supplying and fixing in window frames at 4" centers and painted with two coats Aluminium or anti- corrosive paint.
Pintols for gates and garage doors supplying and fixing in cement concrete (concrete to be paid for separately)
Sheets, G.I plain, 24 B..W.G with hooked joints supplying and fixing to existing frames with wire nails.
Wire mesh 1/2" galvanized, supplying and fixing with available fillets, including removing existing.
Wire mesh 1/4" galvanized, supplying and fixing with available fillets, including removing existing.
Wire mesh 1/16" galvanized, supplying and fixing with available fillets including removing existing.
Tor steel rods in reinforcing lintols, beams, columns and slabs bending to shape, laying in position and tying with G.I wire as directed.
Tor steel rods in foundation or Floors, bending to shape, laying in position and tying with G.I wire as directed.
Supplying and fixing 2"dia. heavy duty GI pipe uprights for receiving chain-link fence. Rate to include for painting one coat of anticorrosive and two coats of enamel paint and welding 6"x6"x1/4" thick MS plate to bottom of pipe and fixing fiberglass pipe cap 2" dia.(Rate exclude cement concrete base & Excavation.)
Supplying and fixing, open area 2"x2", 5' 0"ft. high (gauge 10) galvanized and PVC coated Chain link fence . Fixed to existing GI post and including horizontal bracing with 5/8"x 1/4" MS flat iron with GI J bolts and washers , PVC coated tying wires etc.,
Supplying and fixing, open area 2"x2", 5' 0"ft. high (gauge 12 galvanized and PVC coated Chain link fence . Fixed to existing GI post and including horizontal bracing with 5/8"x 1/4" MS flat iron with GI J bolts and washers , PVC coated tying wires etc.,
Supplying and welding 11/2"x11/2"x1/4"MS angle iron horizontal bracing to existing GI pipe posts. Rate to include for painting one coat of anticorrosive paint and two coats of enamel paint.
BSR 2014- Department of Buildings
S07- 220
Description Item Unit
sq.ft Guard rails ( Heavy duty GI-Pipe)
L.ftHand rails ( Heavy duty GI-Pipe)
L.ft Hand rails (Stainless Steel, 1.5mm thick Pipe- Grade 304 )
L.ftWeb Truss - Fabricating, Hoisting & FixingAs per Drg.No 2013-TP-ST11 & 2013 - TP- ST12
Nr.
Nr.
Nr.
Nr.
Nr.
Nr.
As per Drg.No 2013-TP-ST13 - 2013 - TP- ST18
Fabricating and fixing of MS grills with 1"x1/4" flat iron frame and 1/4"dia.MS. rods welded to diamond shape 3"centres both ways.
Fabricating and fixing of 3' 0" high, heavy duty GI. Pipe Guard railing, consisting of 1½"dia.Vertical pipe (Balusters) raised at 6" intervals & firmly fixed to Concrete floor at bottom & welded to 2"dia.heavy duty Horizontal GI. pipe top rail. Two rows of 1" dia. heavy duty GI pipe bracings welded to Vertical pipes horizontally at mid way.( painting Paid Separately)Considered 20' 0" long hand rail
Fabricating and fixing of 3' 0" high, heavy duty GI. Pipe Hand railing, consisting of ¾" dia. uprights at 12" centers. 1/4" thick 2"x2" M.S plate welded to the bottom end of uprights and embedded in concrete floor. The top end of the upright welded to 1½"dia.G.I hand rail. Considered 11' 2" long hand rail
Fabricating and fixing of 3' 0" high, stainless steel railing, consisting of ¾" dia 1.5mm Thick stainless steel (Pipe) uprights at 12" centers. 1/4" thick 2"x2" M.S plate welded to the bottom end of uprights and embedded in concrete floor, covered with stainless steel base cap. The top end of the upright welded to Stainless Steel Pipes,1½"dia.x 1.5mm Thick , hand rail (All stainless steel members are in Grade 304). Considered 11' 2" long hand rail
Fabricating, Hoisting & Fixing Steel web Truss , Span - 5m consist of 2 Nos of 50 x 50 x 6mm top chord , 2 Nos of 50 x 50 x 6mm bottom chord & 50 x 50 x 6mm bracings. Including all , gusset plates , cleats , rivets , nuts, washers, rag bolts, separators etc.. (Rate shall include for painting of two coats of anticorrosive paint & one coat of enamel paint.) (Hoisting up to 30 ft)
Steel web truss Type T1 with Roof Angle - 150 (Approx. Weight 0.25 M.T)
Steel web truss Type T2 with Roof Angle - 180 (Approx. Weight 0.25 M.T)
Steel web truss Type T3 with Roof Angle - 230 (Approx. Weight 0.26 M.T)
Steel web truss Type T4 with Roof Angle - 300 (Approx. Weight 0.27 M.T)
Steel web truss Type T5 with Roof Angle - 350 (Approx. Weight 0.28 M.T)
Steel web truss Type T6 with Roof Angle - 450 (Approx. Weight 0.32 M.T)
BSR 2014- Department of Buildings
S07- 221
Description Item Unit
Nr.
Nr.
Nr.
Nr.
Nr.
Nr.
Nr.
Nr.
Nr.
Nr.
Nr.
Fabricating, Hoisting & Fixing Steel web Truss , Span - 7m consist of 2 Nos of 50 x 50 x 6mm top chord , 2 Nos of 50 x 50 x 6mm bottom chord & 50 x 50 x 6mm bracings. Including all , gusset plates , cleats , rivets , nuts, washers, rag bolts, separators etc.. (Rate shall include for painting of two coats of anticorrosive paint & one coat of enamel paint.) (Hoisting up to 30 ft)
Steel web truss Type T1 with Roof Angle - 150 (Approx. Weight 0.32 M.T)
Steel web truss Type T3 with Roof Angle - 180 (Approx. Weight 0.32 M.T)
Steel web truss Type T5 with Roof Angle - 230 (Approx. Weight 0.34 M.T)
Steel web truss Type T7 with Roof Angle - 300 (Approx. Weight 0.35 M.T)
Steel web truss Type T9 with Roof Angle - 350 (Approx. Weight 0.36 M.T)
Steel web truss Type T11 with Roof Angle - 450 (Approx. Weight 0.42 M.T)
Fabricating, Hoisting & Fixing Steel web Truss , Span - 7m consist of 2 Nos of 60 x 60 x 6mm top chord , 2 Nos of 60 x 60 x 6mm bottom chord & 50 x 50 x 6mm bracings. Including all , gusset plates , cleats , rivets , nuts, washers, rag bolts, separators etc.. (Rate shall include for painting of two coats of anticorrosive paint & one coat of enamel paint.) (Hoisting up to 30 ft)
Steel web truss Type T2 with Roof Angle - 150 (Approx. Weight 0.36 M.T)
Steel web truss Type T4 with Roof Angle - 180 (Approx. Weight 0.37 M.T)
Steel web truss Type T6 with Roof Angle - 230 (Approx. Weight 0.38 M.T)
Steel web truss Type T8 with Roof Angle - 300 (Approx. Weight 0.39 M.T)
Steel web truss Type T10 with Roof Angle - 350 (Approx. Weight 0.41 M.T)
BSR 2014- Department of Buildings
S07- 222
Description Item Unit
K-BRASS FOUNDER
NosBolts, barrel, brassBolts, barrel, brass, polished, 2 1/2" heavy quality supplying and fixing with brass screws.
NosBolts, barrel, brass, polished, 3" heavy quality supplying and fixing with brass screws.
NosBolts, barrel, brass, polished, 4" heavy quality supplying and fixing with brass screws.
NosBolts, barrel, brass, polished, 5" heavy quality supplying and fixing with brass screws.
NosBolts, barrel, brass, polished, 6" heavy quality supplying and fixing with brass screws.
NosBolts, brass, skeleton 8" supplying & fixing with brass screws. NosBolts, brass, skeleton 10" supplying & fixing with brass screws. NosBolts, brass, skeleton 12" supplying & fixing with brass screws. NosBolts, brass, skeleton 14" supplying & fixing with brass screws. NosCabin Hooks (Brass)Cabin Hooks 2" polished, brass, heavy quality supplying and fixing with brass screws.
NosCabin Hooks 3" polished, brass, heavy quality supplying and fixing with brass screws.
NosCabin Hooks 6" polished, brass, heavy quality supplying and fixing with brass screws.
NosCabin Hooks, 8", polished, brass heavy Quality supplying & fixing with brass screws.
NosCabin Hooks, 9", polished, brass heavy quality supplying & fixing with brass screws.
NosCabin Hooks, 10", polished, brass heavy quality supplying & fixing with brass screws.
NosCabin Hooks, 12", polished, brass heavy quality supplying & fixing with brass screws.
NosCasement fasteners, brass
NosCasement stays, polished 10" heavy quality supplying and fixing. NosCasement stays, polished 12" heavy quality supplying and fixing. NosFanlight Catches, brass heavy quality, supplying and fixing with brass screws complete.
NosHandles, door, brass, polished heavy quality supplying and fixing with brass screws complete.
NosHasp and staple, brass
Nos
Bolts, Casement fasteners or stays, removing and re-fixing including making good to holes in frames and sashes.
Casement fasteners, brass with Motice plate, polished heavy quality supplying and fixing with brass screws.
Hasp and staple, Safety type, 6" brass, polished heavy quality supplying and fixing with brass screws, complete.
BSR 2014- Department of Buildings
S07- 223
Description Item Unit
NosHat Hooks, brass, supplying and fixing with brass screws. NosHinges, brass
pairs
pairs
pairs
pairs
pairs
pairsHinges, gravity, brass supplying and fixing with brass screws complete. pairs
pairs
Nos
NosHinges, Spring, available, repairing and re-fixing. NosHinges, spring, double acting, brass 4" supplying and fixing. Nosfixing Hinges, available complete with brass screws. NosLocks (Brass)
Keys, brass for door locks, making and supplying. NosKnobs for door locks, polished brass, heavy quality, renewing with brass screws.
setLocks, door, available, fixing with screws. NosLocks, door repairing and re-fixing. NosLocks, cupboards, 2 1/2" brass, 4 levers with brass screws supplying and fixing complete.
NosLocks, cupboard, repairing and re-fixing. Nos
NosLocks, rim 5" single lever of best quality local manufacture, supplying and fixing.
NosSupplying and fixing ,night latch/Rim Lock (Duplicate/Local), with duplicate keys.
Nos
Hasp and staple, Safety type, 4" brass, polished heavy quality supplying and fixing with brass screws, complete.
Hinges, butt, 2" brass, polished heavy quality supplying and fixing with brass screws complete.
Hinges, butt, 3" brass polished heavy quality supplying and fixing with brass screws complete.
Hinges, butt, 3 1/2" brass polished heavy quality supplying and fixing with brass screws complete.
Hinges, butt, 4" brass polished heavy quality supplying and fixing with brass screws complete.
Hinges, butt, 5" brass polished heavy quality supplying and fixing with brass screws complete.
Hinges center pivoted (consisting of 2 pieces) brass, polished heavy quality supplying and fixing with brass screws complete.
Hinges, Parliamentary, 4" brass, polished heavy quality supplying and fixing with brass screws complete.
Hinges, Parliamentary, 5" brass, polished heavy quality supplying and fixing with brass screws complete.
Hinges, Parliamentary, 6" brass, polished heavy quality supplying and fixing with brass screws complete.
Note: Refer Item numbers From J057 to J065 for Iron Locks.& Item numbers From U743 to upward for Aluminium Door Locks.
Locks, rim 6" polished brass, 2 levers, superior quality and English make, supplying and fixing.
BSR 2014- Department of Buildings
S07- 224
Description Item Unit
Nos
Nos
NosSupplying & fixing Motice (local) single Lock. NosSupplying and fixing Motice Lock (local) double. Nos
Nos
Nos
Nos
Nos
NosSupplying and fixing RANIYO-PADMA Handle - Black (On Plate) Nos
Supplying and fixing , Yale or Union, night latch Lock (Rim Lock), with duplicate keys. (Nos: 80 or 89),(Imported, British or south African make)
Supplying and fixing Union, night latch Lock (Rim Lock), with duplicate keys. (Nos: 1022,1027 or 1028),(Imported, British or south African make)
Door rings, brass 1 3/4" to 1 1/2" supplying and fixing to doors and windows with brass screws.
Supplying and fixing two Lever single door UNION Motice Lock (No2295),(Imported, British or south African make).
Supplying and fixing two Lever double door UNION Motice Lock (No2242), (Imported, British or south African make).
Supplying and fixing UNION Cylinder Lock (No: PC 064 SC) including Door handle pair,(Imported, British or south African make).
Supplying and fixing UNION Nob set Lock (No:X96300) (Imported, British or south African make).
Supplying and fixing UNION Nob set Lock for Toilets (No:X96350) (Imported, British or south African make).
BSR 2014- Department of Buildings
S07- 225
Description Item Unit
L-PLASTERER
Sqr
SqrSqr
SqrSqr
Cove moulding 2 1/2" x 2 1/2" in cement mortar 1:2 built in existing wall. L.ft
L.ftCresting with broken glass in cement mortar 1:4 on coping of boundary wall.
L.ft Moulding
L.ft
L.ftMoulding 4" x 2" in cement and sand 1:2 built in existing wall. L.ft
L.ft
Nos
SqrPointing flush in cement 1:2 in surface cracks including raking out joints. L.ftPointing, tuck, projected in cement 1:2 on brick masonry etc. sq.ftRendering CementRendering, (1/2") thick, 1:2 cement and sand, above 1 square. SqrRendering, (1/2") thick, 1:2 cement and sand, up to 1 square. SqrRendering, (1/2") thick, 1:3 cement and sand, above 1 square. SqrRendering, (1/2") thick, 1:3 cement and sand, up to 1 square. SqrRendering, (3/4") thick, 1:2 cement and sand , above 1 square. SqrRendering, (3/4") thick, 1:2 cement and sand ,up to 1 Square. SqrRendering, (3/4") thick, 1:3 cement and sand , above 1 square. SqrRendering, (3/4") thick, 1:3 cement and sand ,up to 1 square. SqrCement floating coat.
Sqr
Sqr
Plastering (walls)(5/8") thick plastering to wall in cement lime and sand 1:1:5 finished semi rough with wooden float.
(5/8") thick plastering to wall in cement lime and sand 1:1:5 finished smooth with lime putty floating.
(5/8") thick plastering 1:5 cement and sand semi rough Plastering (beams, slab soffits)3/8" thick plastering to R.C.C. beams, slab soffit in cement and sand 1:3 including floating with lime putty.
Clay plastering and lime puttying smooth.
Repairing cracks in wall, plastered in cement mortar 1:3 after chipping 2" to 4" wide.
Moulding 3" x 1/2" in walls in lime and cement mortar 1:1:4 only for replacements to match existing or to be "extra" over rate for plastering.
Moulding 6" x 1" in walls in lime and cement mortar 1:1:4 only for replacements to match existing or to be "extra" over rate for plastering.
Flashing or plaster bands laid over tiles 4" to 6" wide on roof in cement and lime mortar 1:1:4.
Letters embossed in plaster 3/4" thick up to 6" high in cement and sand 1:2 cement floated and painted complete.
( 5/8") thick plastering to walls in lime and sand 2:5 including floating, finished smooth with lime putty.
Neat cement floating coat on already Layed rendering surface, finish smooth with Mason trowel.
Coloured cement (Red or Black) floating coat on already Layed rendering surface, finish smooth with Mason trowel.
BSR 2014- Department of Buildings
S07- 226
Description Item Unit
SqrColoured cement (Brown or Green) floating coat on already Layed rendering surface, finish smooth with Mason trowel.
BSR 2014- Department of Buildings
S07- 227
Description Item Unit
Cement Rendering and smooth Coloured floating coat
SqrRendering Cement with PudloRendering cement 3/4" 1:2 with Pudlo, 5 lbs. to 100 lbs., cement. SqrSkirting in cement mortar
L.ft
L.ftD.P.C- 3/4"
Sqr
L.ftL.ft
Rendering (3/4") thick, 1:3 cement and sand and floating coat, using Coloured (Red/Black) finished smooth with Mason trowel.
Skirting in cement mortar 1:3, 1/2" x 4" projected or flushed with wall, and finished with neat Cement smooth and including forming groove.
Skirting in cement mortar 1:3, 1/2" x 4" projected or flushed with wall, and finished with Red Cement floating, including forming groove.
D.P.C- 3/4" thick in cement, sand 1:2 finished smooth with 2 coats of hot tar.
Plastering (Reveals)Plastering external reveals 4" wide finished rough. Plastering internal reveals 4" wide finished smooth.
BSR 2014- Department of Buildings
S07- 228
Description Item Unit
M-TINKERGI-Down pipes / Hold fasts
L.ft
L.ft
L.ft
L.ftExtra over Items 1 - 4 in Two storeyed buildings. L.ftExtra over Items 1 - 4 in buildings of Three or more storeys. L.ft
L.ftG.I Flashing
L.ftFlashing G.I refixing, including making good to walls in cement and lime mortar.
L.ftZn/Al-Flashing
L.ftG.I semicircular Gutters
L.ft
L.ftGutter, eaves 6" moulded, G.I 22 B.W.G making and fixing complete including brackets.
L.ftGutters, eaves and down pipes, cleaning in Single Storeyed Buildings. L.ftGutters, eaves and down pipes, cleaning in Two Storey Buildings. L.ftGutters eaves. re-grading in Single Storeyed Buildings. L.ftGutters eaves. re-grading in Two Storeyed Buildings. L.ft
NosGutter heads, 10" x 10" x 2ft 0" making of G.I Sheets 22 B.W.G and fixing.
Nos
NosMaking and fixing Gutter heads, 9" x 9" x 1ft 0" of G.I Sheets 22 B.W.G .
Nos
Making and fixing Down pipes 4" dia. Using G.I 22 B.W.G with holdfasts or plugs fixed to walls in cement 1:3.
Making and fixing Down pipes 6" dia. Using G.I 22 B.W.G with holdfasts or plugs fixing to walls in cement 1:3.
Making and fixing Down pipes, rectangular, using G.I 22 B.W.G. 4" x 3" with holdfasts or plugs fixing to walls in cement 1:3.
Making and fixing Down pipes 4" x 6", circular or Rectangular, with holdfasts or plugs fixing to walls (G.I sheets available)
Down pipes, loose or new, fixing with holdfasts or plugs including making good to walls (down pipes available; Plugs or holdfast to be paid for separately.
Flashing, G.I 22 B.W.G 1ft 6" wide, supplying and fixing with 6" turning up along, and top edge tucking well into wall in cement and lime mortar, including removal of old flashing.
Flashing, 0.47mm thick, Hi Tensile Zn/Al , 1'-6" wide, supplying and fixing with 0'-6" turning up along, and top edge tucking well into wall and groove filled with silicon.
Gutters, eaves 6" G.I semicircular 22 B.W.G making and fixing with hooks or brackets and screws, and joints to be soldered complete.
Gutters, eaves 6" G.I semicircular 22 B.W.G making and fixing with hooks or brackets and screws, and joints to be soldered complete. (G.I sheets available).
Gutters, existing, making opening to receive 4" to 6" down pipe, attaching spigot piece, joints to be soldered and making good.
Gutter heads, 10" x 10" x 2ft 0" making of G.I Sheets 22 B.W.G and fixing. (Sheets available)
BSR 2014- Department of Buildings
S07- 229
Description Item Unit
Making and fixing Gutter heads, 9" x 9" x 1ft 0" of G.I Sheets 22 B.W.G . (Sheets available.) Nos
Gutter hooks or brackets 3/4" x 1/8" supplying and fixing complete with Iron screws. Nos
Gutters, leaks repairing or joints to be soldered. Nos
L.ft
L.ft
L.ftRenewing swan Neck approx. 3ft 4" long 4" dia. 22 B.W.G . Nos
Nos
L.ftValley gutter (G.I)
L.ftZinc Aluminium Colour bonded valley gutter (0.47mm)
L.ft
L.ft Zn/Alu high tensile down pipes
L.ft
L.ft Zn/Alu gutters
L.ftSupplying, fixing 0.47mm tk., Alu gutters (457mm girth) with brackets & specials.
L.ft Zn/Alu Down pipe Bends
Nos
Nos
Gutters, parapet, G.I 3ft 0" overall, 22 B.W.G renewing on existing boards, joints to be soldered and laid complete.
Renewing gutters, valley, 18 B.W.G 36" wide, on existing boards, sheets to be tarred, joints to be soldered and cement, lime filleting complete.
Renewing gutters, valley, 18 B.W.G 36" wide, on existing boards, sheets to be tarred, joints to be soldered and cement lime filleting complete (G.I sheets available)
Making tank, Hot Water, 1ft 6" x 1ft 0" x 1ft 6" high with G.I Sheets, 22 B.W.G riveting and soldering, supplying and fixing (Connecting U pipe and tap to be paid for separately)
Gutters parapet - G.I 3ft 0" overall 22 B.W.G renewing including timber 1" boarding, joints to be soldered and laid complete.
Gutters valley, 18 B.W.G 36" wide, renewing including timber 1" thick boarding, sheet t be tarred, joints to be soldered and cement lime filleting complete.
Supplying and fixing Zinc Aluminium sheet valley gutter (0.47mm) thick ,width 914mm and fixing to roof with self trapping screws.(Excluding timber boarding). Hi-tensile (Grade-550) Colour
Supplying and fixing Zinc Aluminium sheet valley gutter (0.47mm) thick ,width 457mm and fixing to roof with self trapping screws.(Excluding timber boarding) Hi-tensile (Grade-550) Colour
Supplying, fixing 0.47mm tk., Zn/Alu Hi-tensile (Grade-550) Colour down pipe (914mm girth) with brackets.
Supplying, fixing 0.47mm tk., Zn/Alu Hi-tensile (Grade-550) Colour down pipe (457mm girth) with brackets.
Supplying, fixing 0.47mm tk., Alu gutters (914mm girth) with brackets & specials. Hi-tensile (Grade-550) Colour
Supplying, fixing 0.47mm tk., Zn/Alu Hi-tensile (Grade-550) Colour. Down pipe Bend (for 914mm girth gutter) with brackets & specials.
Supplying, fixing 0.47mm tk., Zn/Alu Hi-tensile (Grade-550) Colour. Down pipe Bend (for 457mm girth gutter) with brackets & specials.
BSR 2014- Department of Buildings
S07- 230
Description Item Unit
N-GLAZERGlass panes fixing with (Group 6 category A) timber beadings (Glass available)
sq.ftGlass panes 3 mm clear supplying and fixing with (Group 6 category A) timber beadings.
sq.ftGlass panes 5 mm clear, supplying and fixing with (Group 6,category A) timber Beadings.
sq.ft
sq.ft
sq.ftPaint removing from painted glass panes with Caustic Soda Solution or other paint remover.
sq.ft
Glass panes 5 mm pinhead or obscure supplying and fixing with (Group 6 category A) timber beadings.
Glass panes 3 mm pinhead or obscure supplying and fixing with (Group 6 category A) timber beadings.
BSR 2014- Department of Buildings
S07- 231
Description Item Unit
P-PAINTER & DECORATOR
Scraping Walls
Sqr
Sqr
Sqr
Sqr
Sqr
Sqr Skim coat
Sq.ftCement washing to wallsCement washing to walls of single storeyed buildings, 1 coat, patching and preparing surface.
SqrCement washing to walls of single storeyed buildings, 2 coat, patching and preparing surface.
SqrCement washing externally to walls of building with upper floors, 1 coat. SqrWhite or colour washing walls
Sqr
SqrWhite or Colour washing external walls of two storeyed buildings, 1 coat.
Sqr
Walls, scraped to original plaster, sand papering and lime putting cracks and defects, preparing surface for Distemper, snowcem, paint or similar application.
Walls, scraping and removing soot and leveling internally in Kitchen (extra over colour washing)
Surface preparation (Old work) for Painting (Scraping /Patching /Smoothing)
Surface preparation, old work of Internal faces of walls, scraped to original plaster, patching up cracks and defects, with Acrylic wall putty, applying one coat of Acrylic wall Filler, sand papering and preparation of surface for application of Emulsion or Enamel paint. ( Painting Paid Separately)
Surface preparation, old work of External faces of walls, scraped to original plaster, patching up cracks and defects, with Acrylic wall putty, sand papering and preparation of surface for application of Weather Shield or Enamel paint. ( Painting Paid Separately)
Surface preparation, old work of External faces of walls, scraped to original plaster, patching up cracks and defects, with Acrylic wall putty, sand papering and preparation of surface for application of Weather Shield or Enamel paint in Two Storied building.( Painting Paid Separately)
Surface preparation, old work of External faces of walls, scraped to original plaster, patching up cracks and defects, with Acrylic wall putty, sand papering and preparation of surface for application of Weather Shield or Enamel paint in more than Two Storied building. ( Painting Paid Separately)
Applying Skim Coat compound on walls or soffit two coats, finished smooth with sand papering, and prepare for colour washing.
White or colour washing walls of single storeyed buildings 1 coat, including patching up and preparing surface.
White or colour washing walls of single storeyed buildings 2 coats, including patching up and preparing surface.
BSR 2014- Department of Buildings
S07- 232
Description Item Unit
White or Colour washing external walls in buildings, of more than 2 storeys, 1 coat.Sqr
White or Colour washing external walls in Two storeyed buildings, 2 coats. Sqr
White or Colour washing external walls in building with more than 2 storeys, 2 coats.Sqr
Snowcem paintPainting walls with snowcem or equivalent cement paint, 2 coats to new work.
Sqr
Sqr
SqrAcrylic wall Filler ( Primer for Interior)Painting walls with Acrylic wall Filler. (CIC or Equivalent.) SqrAlkali resisting primerPainting walls with alkali resisting primer where necessary. (CIC or Equip)
SqrElastometic filler PrimerPainting walls with one coat of Elastometic filler Primer where necessary. (CIC or Equivalent.)
SqrAlkali resisting water Proofing sealer
SqrHeat Resistant paint
SqrSilicone masonry water repellent paintPainting Walls with one coat of Silicone masonry water repellent paint. SqrBathroom paintPainting Walls with one coat of Bathroom paint. (CIC or Equivalent.) SqrEmulsion paint (Interior)
Sqr
Sqr
Sqr
SqrPainting General Purpose weather shied ( Exterior)
Sqr
Sqr
Painting walls with snowcem or equivalent cement paint, 2 coats to old walls after scraping existing colour wash, sand papering and wiping down.
Painting walls with snowcem or equivalent cement on old walls after scraping existing colour wash, sand papering and wiping down one coat.
Painting walls with one coat of Alkali resisting water Proofing sealer where necessary. (CIC or Equivalent.)
Applying Heat Resistant paint, one coat to all exposed surfaces on walls already prepared. (CIC or Equivalent.)
Painting Walls with one coat of emulsion paint. (On New work or already prepared old work). (CIC or Equivalent.)
Painting on New walls with two coats of emulsion paint. (Primer coat paid separately) (CIC or Equivalent.)
Painting Walls with Emulsion paint, One coat including preparing surface of old work. (CIC or Equivalent.)
Painting Walls with Emulsion paint, Two coats including preparing surface of old work. (CIC or Equivalent.)
Painting external walls with One coat of weather shied paint. (Excluding Primer Coat). (CIC or Equivalent.)
Painting external walls with Two coats of weather shied paint. (Excluding Primer Coat). (CIC or Equivalent.)
BSR 2014- Department of Buildings
S07- 233
Description Item Unit
Sqr
Sqr
Sqr
SqrAcrylic Emulsion (Exterior paint)
SqrPainting asbestos sheet roof
Sqr
Sqr
Sqr
SqrFloor Painting
Sqr
SqrEpoxy Floor Painting
Sqr
SqrAnticorrosive paint
Sqr
SqrPainting on GI Surface
Sqr
Painting on old work with General Purpose weather shied (Exterior paint) , including surface preparation.
Painting walls with weather shied paint One coat including wire brushing and sand papering of old work. (CIC or Equivalent.)
Painting walls with weather shied paint Two coat including wire brushing and sand papering of old work. (CIC or Equivalent.)
Painting on New work with, Two Coats of Acrylic Emulsion weather shied (Exterior paint), and One coat of Elastometic filler Primer (under Coat).
Painting on New work, weather shied (Exterior paint) One Coat, with One Primer under Coat. -(CIC or Equivalent.)
Painting on New work, weather shied (Exterior paint) Two Coats , with One Primer under Coat. -(CIC or Equivalent.)
Painting external walls with Two coats of Acrylic Emulsion (Exterior paint) paint resist against algae, fungus and scrubs. (On New work or already prepared old work). -(CIC or Equivalent.)
Painting over the asbestos sheet roof with Two coats of roof shield paint. (CIC or Equivalent.)
Painting under side of asbestos roofing sheet with One coat of emulsion paint (CIC or Equivalent.)
Painting under side of asbestos roofing sheet with Two coats of emulsion paint (CIC or Equivalent.)
Painting under side of asbestos roofing sheet with One coat of primer after preparing surface (CIC or Equivalent.)
Painting floors with One coat of quick drying Floor paint including washing, cleaning and smoothing down the surface. (CIC or Equivalent.)
Painting floors with Two coats of quick drying Floor paint including washing, cleaning and smoothing down the surface. (CIC or Equivalent.)
Painting floors with One coat of Epoxy Floor Paint including washing, cleaning and smoothing down the surface. (CIC or Equivalent.)
Painting floors with Two coats of Epoxy Floor Paint including washing, cleaning and smoothing down the surface. (CIC or Equivalent.)
Painting steelwork, One coat with anticorrosive paint including removing scale and wire brushing. (CIC or Equivalent.)
Painting steelwork, Two coats, with anticorrosive paint including removing scale and wire brushing. (CIC or Equivalent.)
Painting new galvanized iron GI Adhesion Promoter One coat and One coat of Dulux metal primer Zink chromate or duco oil primer or equivalent including washing surface with water after manufactures specification.
BSR 2014- Department of Buildings
S07- 234
Description Item Unit
Aluminium paintSqrL.ftL.ft
Aluminium paint, One coat on metal surfaces. (CIC or Equivalent.)Aluminium paint, One coat, along 2" thick band. (CIC or Equivalent.)Aluminium paint, Two coats, along 2" thick band. (CIC or Equivalent.)
BSR 2014- Department of Buildings
S07- 235
Description Item Unit
Enamel paint
Sqr
SqrRemoval of Paint from timber. Paint removed entirely with blow lamp to bare timber. Sqr
L.ftWood preservative Wood preservative, (clear) applied to woodwork one coat (old work) (CIC or Equivalent.)
SqrWood preservative, (clear) applied to woodwork two coats (New work) (CIC or Equivalent.)
SqrEnamel paint with Wood primer Under coat
SqrPainting new woodwork with approved primer, one coat. (CIC or Equivalent.)
SqrPolishing wood work with Wax
SqrPainting with Wood sheen
Sqr
SqrPolyurethane Varnishing
Sqr
Sqr
Sqrpolyurethane varnish-Matt
Sqr
SqrRemoving VarnishVarnishing, removing entirely to bare timber and preparing surface. SqrPainting with Sanding sealer / Woof finish Lacquer
Sqr
Sqr
Painting One coat of Enamel paint, including washing and cleaning the surface. (CIC or Equivalent.)
Painting Two coats of Enamel paint, including washing and cleaning the surface. (CIC or Equivalent.)
Painting G.I pipes 3/4" to 1/2" with approved paint, 2 coats.
Painting new woodwork, with primer, undercoat and Two coats of enamel paint. (CIC or Equivalent.)
Polishing Woodwork with Wax, including thoroughly sand papering surface in new work only of permanent fixtures.
Painting with Wood sheen paint including washing cleaning and smoothing down surface, One coat.
Painting with wood sheen paint including washing cleaning and smoothing down surface, Two coats.
Varnishing on old wood surface with one coat of polyurethane varnish-Gloss, after washing down and sand papering.
Varnishing on old wood surface with two coats of polyurethane varnish-Gloss, after washing down and sand papering.
Varnishing on New wood work with one coat of sanding sealer and two coats of polyurethane varnish-Gloss, after sand papering.
Varnishing with polyurethane varnish-Matt, after washing down and sand papering, Two coats.
Varnishing on New wood work with one coat of sanding sealer and two coats of polyurethane varnish-Matt, after sand papering.
Applying new woodwork with Two coats of Sanding sealer and two coats of wood finish
Applying wood finish, one coat, including washing, cleaning and smoothing down surface.
BSR 2014- Department of Buildings
S07- 236
Description Item Unit
SqrApplying wood finish, one coat, including two coats of sanding sealer after washing, cleaning and smoothing down surface.
BSR 2014- Department of Buildings
S07- 237
Description Item Unit
Painting with Perque varnish
Sq.ftSqr
Painting Letters on (Board / Wall)Lettering 1" to 1 1/2" painted in Sinhalese, English or Tamil, including painting background.
NosLettering 2" to 3" painted in Sinhalese, English or Tamil, including painting background.
NosLettering 4" to 5" painted in Sinhalese, English or Tamil, including painting background.
Nos
Cutting, leveling ,polishing and applying two coats of Perque varnish for an existing timber base floor.
Applying masonry sealer for walls One coat.
BSR 2014- Department of Buildings
S07- 238
Description Item Unit
Q-PLUMBERBall valve-UPVC
NosSupplying & fixing UPVC ball valve 3/4" dia. (S-Lon or equivalent) NosSupplying & fixing UPVC ball valve 1" dia. (S-Lon or equivalent) NosSupplying & fixing UPVC ball valve 1 1/4" dia. (S-Lon or equivalent)
NosFixing ball valve 1/2" to 1" (available.) NosBall valve-BrassRepairing & fixing ball valve. removing and refixing NosSupplying & fixing Brass Ball valve ½" or 20mm-(Peglar or equivalent.) NosSupplying & fixing Ball valve Brass ¾" or 25mm-(Peglar or equivalent.) NosSupplying & fixing Ball valve Brass 1" or 32mm-(Peglar or equivalent.) Nos
NosSoldering & fixing ball to lever operating Valve (available) NosConcealed Taps/Valves-Chromium platedSupply and fixing concealed valve 1/2"dia. NosSupplying and fixing Concealed valve 1/2"dia.(American Standard or Equivalent.)
Nos
Supplying & fixing Concealed Taps/Valves-Chromium plated ½" dia.(Plumber)Nos
Flush valveSupplying and fixing cobra flush valve NosSupplying and fixing wall Urinal Flush Valve(FM 3A903)-High Quality Nos
Supplying and fixing wall Urinal Sensor Flush Valve(FM 3L303)-High QualityNos
Flush valve to existing Urinal (Imported )Supplying and fixing wall Urinal Flush Valve(Cobra)-High Quality Nos
Supplying & fixing flush valve to existing Urinal (American Standard or Equivalent.)Nos
Gate valve brass for Max. 17.5 bars (Pegler 1065 or equivalent)
Nos
Supplying & fixing UPVC ball valve 1/2" dia. (S-Lon or equivalent)
Supplying & fixing Ball valve Brass 1½" or 63mm -(Peglar or equivalent.) with necessary fittings.
Prime cost of 1/2" dia: chromium Concealed valve (American Standard) Rs4,450 ** (2665)
Prime cost of bib tap, Concealed Taps/Valves-Chromium plated ½" dia.(Plumber) Rs 1890 ** (1878)
Prime cost of wall Urinal Flush Valve(Rocell)-High Quality with brackets. .Rs.6,328 ** (2817)
Prime cost of wall Sensor Flush Valve(Rocell)-High Quality with brackets. .Rs.18,180 ** (2818)
Prime cost of wall Urinal Flush Valve(Cobra)-High Quality with brackets. .Rs.9,500 ** (2626)
Prime cost of flush valve to existing Urinal (American Standard).Rs.5,000 ** (2659)
Supplying and fixing 3/8" dia: gate valve brass imported (Pegler or equivalent, approved quality).
BSR 2014- Department of Buildings
S07- 239
Description Item Unit
Nos
Nos
Nos
Nos
Nos
NosGate valve brass for Max. 20 bars (Pegler 1068 or equivalent)
Nos
Nos
Nos
Nos
Nos
Nos
Nos
Nos
Nos
NosFloat valve (Pegler 855 or equivalent)Supplying & fixing 1/2" dia. brass float valve with necessary fittings NosSupplying & fixing 3/4" dia. brass float valve with necessary fittings NosSupplying & fixing 1" dia. brass float valve with necessary fittings NosSupplying & fixing 1 1/4" dia. brass float valve with necessary fittings NosSupplying & fixing 1 1/2" dia. brass float valve with necessary fittings NosSupplying & fixing 2" dia. brass float valve with necessary fittings NosFoot valve BrassSupplying & fixing 1" dia. Copper foot valve with necessary fittings NosSupplying & fixing 1 1/2" dia. Copper foot valve with necessary fittings NosSupplying & fixing 2" dia. Copper foot valve with necessary fittings NosFoot valve PVC
Supplying and fixing 1/2" dia: gate valve brass imported (Pegler or equivalent, approved quality).
Supplying and fixing 3/4" dia: gate valve brass imported (Pegler or equivalent, approved quality).
Supplying and fixing 1" dia: gate valve brass imported (Pegler or equivalent, approved quality).
Supplying and fixing 1 1/4" dia: gate valve brass imported (Pegler or equivalent, approved quality).
Supplying and fixing 1 1/2" dia: gate valve brass imported (Pegler or equivalent, approved quality).
Supplying and fixing 2" dia: gate valve brass imported (Pegler or equivalent, approved quality).
Supplying and fixing 1/4" dia: gate valve brass imported (Pegler or equivalent, approved quality).
Supplying and fixing 1/2" dia: gate valve brass imported (Pegler or equivalent, approved quality).
Supplying and fixing 3/4" dia: gate valve brass imported (Pegler or equivalent, approved quality).
Supplying and fixing 1" dia: gate valve brass imported (Pegler or equivalent, approved quality).
Supplying and fixing 1 1/4" dia: gate valve brass imported (Pegler or equivalent, approved quality).
Supplying and fixing 1 1/2" dia: gate valve brass imported (Pegler or equivalent, approved quality).
Supplying and fixing 2" dia: gate valve brass imported (Pegler or equivalent, approved quality).
Supplying and fixing 2 1/2" dia: gate valve brass imported (Pegler or equivalent, approved quality).
Supplying and fixing 3" dia: gate valve brass imported (Pegler or equivalent, approved quality).
Supplying and fixing 4" dia: gate valve brass imported (Pegler or equivalent, approved quality).
BSR 2014- Department of Buildings
S07- 240
Description Item Unit
Supplying & fixing 1" dia. PVC foot valve with necessary fittings (L/D or equivalent)Nos
Supplying & fixing 1 1/4" dia. PVC foot valve with necessary fittings (L/D or equivalent)Nos
Supplying & fixing 1 1/2" dia. PVC foot valve with necessary fittings (L/D or equivalent)Nos
Supplying & fixing 2" dia. PVC foot valve with necessary fittings (L/D or equivalent)Nos
Supplying & fixing 2 1/2" dia. PVC foot valve with necessary fittings (L/D or equivalent)Nos
Supplying & fixing 3" dia. PVC foot valve with necessary fittings (L/D or equivalent)Nos
Lavatory Basin
NosFixing Basin, Lavatory, existing brackets. (Tap, Waste trap and Basin available).
Nos
Nos
Nos
Nos
Nos
Removing bath room FittingsRemoving basin, sink or urinal including all fittings, and making walls good.
Nos
Nos
Nos
NosFixing bends, elbows, tees, crosses, G.I any size up to 2" (fittings available)
NosSupplying and fixing bends, G.I 1/2". NosSupplying and fixing bends, G.I 3/4". Nos
Fixing Lavatory Basin to wall, and connecting to existing water service and making good. (Basin, brackets and fittings available).
Supplying & fixing complete Basin, Lavatory, 22" x 16" with waste plug, new brackets, (tap, trap, and outlet pipe will be paid for separately)
Supplying & fixing complete Basin, Lavatory, 22" x 16" with waste plug, existing brackets, ( tap, trap, and outlet pipe will be paid for separately).
Prime cost of Basin and waste plug cuplins , 22" x 16" (Approved quality) Rs.2900 ) ** (1574)
Supplying & fixing complete Basin, Lavatory, 25" x 18" with waste plug, new brackets, ( tap, trap, and outlet pipe will be paid for separately)
Prime cost of Basin, Lavatory, 25" x 18" with waste plug, (Approved quality) Rs.3600 ) ** (1575)
Supplying & fixing complete Basin, Lavatory, 25" x 18" with waste plug, on existing brackets, ( tap, trap, and outlet pipe will be paid for separately).
Prime cost of Basin, Lavatory, 25" x 18" with waste plug, (Approved quality) Rs.3800 ) ** (1576)
Baths, C.I enamel, removing and re-fixing in New position and making good to walls and floors (Extra piping required will be paid for separately)
Fixing bath, enameled, C.I. any size, including trap, tap outlet, pipes etc. complete (Bath and fittings available).
supplying and fixing bath, enameled, 3" roll edge, C.I 5ft 6" including trap, tap etc. (out-let pipes will be paid for separately)
BSR 2014- Department of Buildings
S07- 241
Description Item Unit
Supplying and fixing bends, G.I 1". NosSupplying and fixing bends, G.I 1 1/4". NosSupplying and fixing bends, G.I 1 1/2". NosSupplying and fixing bends, G.I 2". NosSupplying and fixing bends, G.I 3". Nos
BSR 2014- Department of Buildings
S07- 242
Description Item Unit
Closet-pedestal type
Nos
NosSupplying & fixing ,pedestal closet (Indian make) ( seat and cover available)
Nos
NosPlastic seat cover, importedSupplying and fixing plastic seat cover, imported, approved quality. Nos
Nos
Nos
Nos
Nos
Fixing closet, pedestal type, available at site with cement concrete after breaking concrete floor, and making good and making connections to soil and flush pipes.
Closet, pedestal type, disconnecting and plugging sewer connection and making good all affected walls and floors.
Prime cost of pedestal closet with seat and cover (Indian make) is Rs.7,500 ** ( 1587)
Supplying & fixing closet, pedestal type, approved quality with low level glazed earthenware flushing cistern, flush pipe double plastic seat cover, 1/2" stop cock, trap etc. (Indian make)
Close coupled water closet suite (white) -ImportedSupplying & fixing, close coupled water closet suite, white, (4/2.6 Lit ) with water closet Pan, Cistern, Seat & Seat cover and trap etc.: complete (Twyford- Rearesh brand or equivalent approved quality).
Prime cost of close coupled water closet suite, (4/2.6 Lit ) with water closet Pan, Cistern, Seat & Seat cover and trap is Rs29,956 (Excluding 12% VAT ) (Refresh-Twyford or equivalent approved quality). ** (1846)
Supplying & fixing, close coupled water closet suite, white, (4/2.6 Lit ) with water closet Pan, Cistern, Seat & Seat cover and trap etc.: complete. (BECA-American standards)
Prime cost of close coupled water closet suite (BECA-American standards) is Rs.31,935 (Excluding 12% VAT ) ** (2646)
Close coupled water closet suite (white)-Manufactured in Sri Lanka.
Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite (white / Colour) with wash down 6/3 liter dual flushing. Has a horizontal outlet and cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: URBAN-D )
Prime cost of Close coupled water closet suite, white (Urban D-Rocell) is Rs.15,625 (Excluding 12% VAT ) ** (2647)
Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite(White/ Colour) with wash down 6/3 liter dual flushing. Has a horizontal outlet and cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: DUNE )
Prime cost of Close coupled water closet suite, white (Dune-Rocell) is Rs.18,598 (Excluding 12% VAT ) ** (2648)
BSR 2014- Department of Buildings
S07- 243
Description Item Unit
Nos
Nos
Nos
Nos
Nos
Nos
Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: INTENCE )
Prime cost of Close coupled water closet suite, Coloured ( INTENCE-Rocell) is Rs.28,929 (Excluding 12% VAT ) ** (2649)
Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: Elements Aqua )
Prime cost of Close coupled water closet suite, Coloured ( Elements Aqua-Rocell) is Rs.24,598 (Excluding 12% VAT ) ** (2826)
Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: Aqua+ )
Prime cost of Close coupled water closet suite, Coloured ( Aqua+ -Rocell) is Rs.27,008 (Excluding 12% VAT ) ** (2649)
Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: Summer Blue )
Prime cost of Close coupled water closet suite, Coloured ( Summer Blue -Rocell) is Rs.65,580 (Excluding 12% VAT ) ** (2649)
Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. In-Wall Tank Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: Eternity )
Prime cost of Close coupled water closet suite, Coloured ( Eternity-Rocell) is Rs.57,678 (Excluding 12% VAT ) ** (2649)
Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. In-Wall Tank Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: Urbanity )
Prime cost of Close coupled water closet suite, Coloured ( Urbanity-Rocell) is Rs.58,750 (Excluding 12% VAT ) ** (2649)
BSR 2014- Department of Buildings
S07- 244
Description Item Unit
Nos
Nos
Close coupled water closet suite (colour)
Nos
Close coupled European type low level commode suit (white )
Nos Bidet, pedestal type-Imported
Nos
Bidet, pedestal type, Manufactured in Sri Lanka.
Nos
Nos
Bath wear set (3-Pieces)-Fixing Only
Nos
Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. In-Wall Tank Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: Escape )
Prime cost of Close coupled water closet suite, Coloured ( Escape-Rocell) is Rs.58,214 (Excluding 12% VAT ) ** (2649)
Supplying & fixing, Vitreous china floor standing close coupled, Water Closet (toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and two lateral holes for bottom water connection. Cistern with water inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell , Model: TT )
Prime cost of Close coupled water closet suite, Coloured ( TT-Rocell) is Rs.31,875 (Excluding 12% VAT ) ** (2649)
Supplying and fixing closed couple water closet suit (Coloured) with flushing cistern ,flush pipe, double plastic sheet cover ,stop cock, trap etc.(Twyford or equivalent approved quality)
Prime cost of Close coupled water closet suite, colour is Rs.45,000 (Excluding 12% VAT ) ** (2176)
Supplying and fixing close coupled European type low level commode suit white colour with 9 liter capacity which vitreous China low level cistern.(Twyford -Refresh brand)
Supplying & fixing bidet, pedestal type, with mixer taps and necessary specials, Twyford-Refresh brand or equivalent approved quality.
Prime cost of floor standing bidet in white colour (Twyford).Rs 44,645 (Excluding 12% VAT )** (1845)
Supplying & fixing Vitreous china floor standing bidet (white colour), Nominal size ( 22" x 14 1/2") floor to Rim height 16", complete with overflow hole, deck mounted single hole center set bidet faucet. (Dune-Rocell) Faucets not included
Prime cost of floor standing bidet in white colour (Dune-Rocell).Rs 9200 (Excluding 12% VAT ) ** (2655)
Supplying & fixing Vitreous china floor standing bidet (white colour), Nominal size (22"x151/2") floor to Rim height 16 1/2", complete with overflow hole, deck mounted single hole center set bidet faucet.(Urband D-Rocell) Faucets not included
Prime cost of floor standing bidet in white colour (Urband D-Rocell).Rs 9110 (Excluding 12% VAT ) ** (2656)
Fixing pedestal wash basin pedestal low level cistern & bidet with necessary specials & connecting to existing service line (Fittings are available.)
BSR 2014- Department of Buildings
S07- 245
Description Item Unit
Closet-squatting typeSupplying & fixing closet, squatting type, with trap. (Indian) NosRemoving Closet-squatting typeRemoving closet, squatting type, plugging sewer connections and floor made good.
NosFixing available Closet-squatting type
Nos
Nos
NosSquatting pan- European
Nos
Nos
Squatting pan Ceramic ( Indian)Supplying & fixing squatting pan with foot rest Ceramic (Indian or equivalent)
Nos
Closet squatting type ( Indian or equivalent)
Nos
Cistern high level (Plastic)- ( Indian or equivalent)Supplying & fixing flushing cistern high level (Plastic). Nos
Cistern high level, ceramic-(Twyford or equivalent approved quality)
Nos
Cistern, high level, auto flush-CeramicNos
Cistern, high level, auto flush-Plastic
Nos
Fixing in cement concrete closet, squatting type, fixed, including breaking floor (closet available)
Fixing in cement concrete closet, squatting type, fixed including trap, including breaking floor (closet and trap available)
Fixing closet, squatting type, including flushing cistern and pipes complete. (Closet and all fittings available)
Supplying and fixing foot rest squatting pan and trap white to working order.(Twyford or equivalent approved quality)
Prime cost of Squatting pan (White) and trap is Rs. 17,500 ** ( 2165)
Supplying and fixing foot rest type squatting pan and trap colour to working order.(American standards)
Prime cost of (100 F) Squatting pan and trap (American standards) Rs. 15,940 ** ( 2179)
Prime cost of squatting pan with foot rest Ceramic Indian is Rs. 1700 ** (1875)
Supplying & fixing closet squatting type with trap complete with cistern plastic flush pipe etc.: Indian or equivalent (approved quality).
Prime cost of- squatting pan with foot rest Ceramic Indian is Rs. 1700 ** (1826) - plastic cistern Indian is Rs. 2450 ** (1827)
Prime cost of plastic cistern Indian is Rs. 2450 ** (1827)
Supplying and fixing ceramic high level cistern with fittings white ,complete.(Twyford or equivalent approved quality)
Prime cost of High level Cistern, ceramic is Rs.17,500 ** ( 2177)
Supplying & fixing high level ceramic automatic cisternPrime cost of High level automatic ceramic cistern is Rs. 6,600 ** ( 1895)
Supplying & fixing high level cistern plastic auto flush (2 gallons capacity) complete with flush pipe, sprinkler pipe, necessary fittings complete to working order.
BSR 2014- Department of Buildings
S07- 246
Description Item Unit
Prime cost of High level auto flush plastic cistern is Rs.5,700 ** ( 1859)
BSR 2014- Department of Buildings
S07- 247
Description Item Unit
Cistern low level, flushing- porcelain (Indian , approved quality).Supplying & fixing flushing cistern low level porcelain Coloured, (Indian , approved quality).
Nos
Syphon Supplying and fixing syphon for existing cistern (Indian) Nos
Supplying and fixing syphon for existing cistern (American Standard or Equivalent.)Nos
Magic BendSupplying and Magic bend 4" dia. For existing W.C. set etc. Nos
Urinal(Indian)Supplying & fixing urinal, wall type. Nos
Nos Urinal Imported- TwyfordSupplying and fixing bowl urinal white.(Twyford or equivalent approved quality)
Nos
Supplying and fixing bowl urinal colour.(Twyford or equivalent approved quality)Nos
Nos
Nos
Nos
Nos
Nos
Nos
Sink and fittings-Fixing OnlyFixing sink, any size, complete with waste plug, trap & brackets (sink and fittings available)
Nos
Prime cost of Flushing cistern low level porcelain Coloured (Indian , approved quality).Rs.2,850 ** ( 1881)
Prime cost of Syphon cistern (Indian).Rs.850 ** (2178)
Prime cost of Syphon cistern (American standerd-S.No:3343).Rs.1940 ** (2158)
Prime cost of Magic bend 4 dia. .Rs.650 ** (1904)
Prime cost of Urinal (wall type) .Rs.1625 ** (1720)Fixing available urinal, wall type.
Prime cost of Urinal (wall type, white) .Rs. 8,360 ** (2174)
Prime cost of Urinal (wall type, Colour) .Rs.9,500 ** (2175)Supplying and fixing (New wash brook) urinal.(American standards)Prime cost of New wash brook urinal.(American standards) .Rs.16,600 ** (2658)
Supplying & fixing Wall urinal with brackets.(American standards)Prime cost of wall urinal with brackets.(American standerds-412).Rs7,762 ** (2660)
Urinal - Manufactured in Sri Lanka.Supplying & fixing Wall urinal with Flush Valve.(Flo Point Urinal - Rocell)
Prime cost of wall urinal with brackets.Rs23,125* (2819)Supplying & fixing Wall urinal with Flush Valve.(Dew Point Urinal - Rocell)
Prime cost of wall urinal with brackets.Rs15,982* (2821)Supplying & fixing Wall urinal with Sensor.(Flo Point Urinal - Rocell)Prime cost of wall urinal with brackets.Rs34,732* (2820)Supplying & fixing Wall urinal with Sensor.(Dew Point Urinal - Rocell)
Prime cost of wall urinal with brackets.Rs29,375 (2822)
BSR 2014- Department of Buildings
S07- 248
Description Item Unit
Sink
Nos
Nos
Nos
NosReplacing SinkRemoving & refixing sink or basin, in new position. Nos
NosStainless steel kitchen sink
Nos
Nos
Nos
Nos
Wash Basin
Nos
Supplying and fixing Wash Basin with pedestal 25"x18"white.(Twyford -Refresh Brand)Nos
Supplying & fixing sink, glazed, earthenware 30" x20"x8" with waste plug, brackets etc. complete.
Prime cost of Sink, glazed, earthenware 30" x20"x8" waste plug & chain.Rs.3,650 ** (1671)
Supplying & fixing sink, glazed, earthenware 30" x 18" x 8" with waste plug, on existing supports.
Prime cost of Sink, glazed, earthenware 30" x18"x8" waste plug & chain.Rs.3500 ** (1673)
Supplying & fixing sink, glazed earthenware 24" x 18" x 8" with waste plug, brackets etc., complete.
Supplying & fixing sink, glazed, earthenware 24" x 18" x 8" with waste plug, on existing supports.
Sink built in brick in cement 1:5 & cement rendered 1/2" (1:2), 2ft 0" x 2ft 0" with 6" high curb including making hole in wall and supplying & fixing 2" outlet pipe.
Supplying & fixing approved quality, stainless steel kitchen sink with single bowl & draining board with necessary waste plug, brackets etc.:
Prime cost of Stainless steel kitchen sink with single bowl & draining board.Rs.3000 ** (1835)
Supplying & fixing approved quality, stainless steel kitchen sink with double bowl & draining board with necessary waste plug, brackets etc.:
Prime cost of Stainless steel kitchen sink with double bowl & draining board.Rs.10,000 ** (1836)
Supplying & fixing 800X510mm stainless steel kitchen sink with single bowl & draining board with necessary waste plug, brackets etc.: (Teka or Equivalent)
Prime cost of Stainless steel kitchen sink with single bowl & draining board.Rs.17,277** (2810)
Supplying & fixing 1600X510mm stainless steel kitchen sink with double bowl & draining board with necessary waste plug, brackets etc.: (Teka or Equivalent)
Prime cost of Stainless steel kitchen sink with single bowl & draining board.Rs.35,135* (2811)
Supplying & fixing wash Basin 22"x16" white pedestal type with pillar tap, waste plug and other necessary fittings.(Indian approved quality)
Prime cost of Wash Basin 22"x16" white pedestal type (Indian or equivalent).Rs.5,355 (Excluding 12% VAT ) ** (1870)
Prime cost of wash basin 25"x18"(Twyford or equivalent approved quality).Rs18,755 (Excluding 12% VAT ) ** (2256)
BSR 2014- Department of Buildings
S07- 249
Description Item Unit
Nos
Wash Basin (local Bath wear)
Nos
Nos
Nos
Nos
Nos
supplying and fixing Lavatory wash basin with pedestal 20"x18" (American Standerd-Kimera)
Prime cost of wash basin & pedestal (American Standard).Rs 21,735 (Excluding 12% VAT ) ** (2261)
Supplying & fixing Vitreous China floor standing wash basin (white colour) having nominal side of ( 23"x 18" ) with universal height pedestal of floor to Rim height 33", over flow hole and single tap hole in center, including pedestal, Wash basin fixing kit. (Urband D-Rocell) Cupling, Faucets, waste pipe, paid separately
Prime cost of Wash basin 23"x 18" ) with universal height pedestal (Urband D-Rocell). Rs 6,607 (Excluding 12% VAT ) ** (2651)
Supplying & fixing Vitreous China floor standing wash basin (white colour) having nominal side of (241/2"x 19") with universal height pedestal of floor to Rim height 32 1/2", over flow hole and single tap hole in center, including pedestal, Wash basin fixing kit. (Dune-Rocell) Cupling, pipe, paid separately
Prime cost of Wash basin (white colour) ( 24 1/2"x 19" ) with universal height pedestal (Dune-Rocell). Rs 8,009 (Excluding 12% VAT ) ** (2652)
Supplying & fixing Vitreous China floor standing wash basin (white colour) having nominal side of (241/2"x 19") with universal height pedestal of floor to Rim height 32 1/2", over flow hole and single tap hole in center, including pedestal, Wash basin fixing kit. (Intense-Rocell)
Cupling, pipe, paid separately
Prime cost of Wash basin (white colour) ( 24 1/2"x 19" ) with universal height pedestal (Intense-Rocell). Rs 15,670 (Excluding 12% VAT ) ** (2653)
Supplying & fixing Vitreous China floor standing wash basin (white colour) having nominal side of (241/2"x 19") with universal height pedestal of floor to Rim height 32 1/2", over flow hole and single tap hole in center, including pedestal, Wash basin fixing kit. (Elements Aqua-Rocell) Cupling, pipe, paid separately
Prime cost of Wash basin (white colour) ( 24 1/2"x 19" ) with universal height pedestal (Elements Aqua-Rocell). Rs 14,642 (Excluding 12% VAT ) ** (2823)
Supplying & fixing Vitreous China floor standing wash basin (white colour) having nominal side of (241/2"x 19") with universal height pedestal of floor to Rim height 32 1/2", over flow hole and single tap hole in center, including pedestal, Wash basin fixing kit. (Aqua+ -Rocell)
Cupling, pipe, paid separately
Prime cost of Wash basin (white colour) ( 24 1/2"x 19" ) with universal height pedestal (Aqua+ -Rocell). Rs 15,178 (Excluding 12% VAT ) ** (2825)
BSR 2014- Department of Buildings
S07- 250
Description Item Unit
Nos
Nos
Nos
Nos
Corner wash basin (Imported quality)
Nos
Corner wash basin (Indian, approved quality)
Nos
Corner wash basin (local Bath wear)
Nos
Vanity basin
Nos
Supplying & fixing Vitreous China floor standing wash basin (white colour) wall mounted brackets, over flow hole and single tap hole in center, Wash basin fixing kit. (Summer Blue-Rocell) Cupling, pipe, paid separately
Prime cost of Wash basin (white colour) (Summer Blue-Rocell). Rs 30,803 (Excluding 12% VAT ) ** (2827)
Supplying & fixing Vitreous China floor standing wash basin (white colour) wall mounted brackets, over flow hole and single tap hole in center, Wash basin fixing kit. (Eternity-Rocell)
Cupling, pipe, paid separately
Prime cost of Wash basin (white colour) (Eternity-Rocell). Rs 14,285 (Excluding 12% VAT ) ** (2829)
Supplying & fixing Vitreous China floor standing wash basin (white colour) wall mounted brackets, over flow hole and single tap hole in center, Wash basin fixing kit. (Urbanity-Rocell) Cupling, pipe, paid separately
Prime cost of Wash basin (white colour) (Urbanity-Rocell). Rs 19,642 (Excluding 12% VAT ) ** (2831)
Supplying & fixing vitreous chaina wash basin 22"x15" Coloured with pedestal ( Equivalent to Rocell)
Prime cost of Wash basin 22"x15" Coloured with pedestal ( Equivalent to Rocell) .Rs 5,355 (Excluding 12% VAT ) ** (1870)
Supplying & fixing corner wash basin with one tap waste plug, new brackets etc.(Imported quality)
Prime cost of corner wash basin with one tap waste plug, new brackets. Rs 2,750 ** (1883)
Supplying & fixing corner wash basin with one tap, waste plug, new brackets etc.(Indian, approved quality)
Prime cost of corner wash basin with one tap, waste plug, new brackets etc.(Indian, approved quality) Rs 2,850 (Excluding 12% VAT ) ** (1885)
Supplying & fixing corner wash basin with one tap, waste plug, new brackets etc.(Aqua Corner - Rocell)
Prime cost of corner wash basin waste plug, new brackets etc.(Aqua Corner - Rocell) Rs 5,892 (Excluding 12% VAT ) ** (2835)
Supplying and fixing Vanity basin 25"x16" white.(Refresh-Twyford or equivalent approved quality)
Prime cost of Vanity Basin 25"x16"white.(Twyford or equivalent approved quality) Rs 15,000 (Excluding 12% VAT ) ** (2302)
BSR 2014- Department of Buildings
S07- 251
Description Item Unit
Nos
Rubber plugsSupplying & fixing plugs, rubber 1" to 1 1/4" for wash basins and sinks. NosSupplying & fixing plugs, rubber 1 1/2" to 2" for wash basins and sinks. NosWooden plugs
NosBottle trapsSupplying & fixing 1 1/4" dia: plastic bottle trap (Indian or equivalent, approved quality).
Nos
Supplying & fixing 1 1/2" dia: plastic bottle trap (Indian or equivalent, approved quality).Nos
Supplying & fixing 2" dia: plastic bottle trap (Indian or equivalent, approved quality).Nos
Supplying & fixing 1 1/4" dia: bottle trap stainless steel approved quality. Nos
Supplying & fixing 1 1/2" dia: bottle trap stainless steel approved quality.Nos
PVC P-Trap (2" dia.)Nos
Fixing and Repairing , available TapsFixing cocks, brass any size, bib or push. (cock available) NosRemoving cocks, brass bib, push or stop cock, 1/2" to 1 1/2". NosRepairing cocks, bib or stop by fixing leather washers. NosRepairing cocks, self closing by fixing leather washer. NosBib Taps (Metallic)Supplying & fixing brass, bib taps, 1/2" (Chinese or equivalent, approved quality)
Nos
Supplying & fixing brass, chromium plated bib tap 1/2" . (Plumber or Equivalent.)Nos
Supplying and fixing Vanity basin 25"x16"colour.(Galerie-Twyford or equivalent approved quality)
Prime cost of Vanity Basin 25"x16"white.(Twyford or equivalent approved quality) Rs 17,500 (Excluding 12% VAT ) ** (2303)
Bedding in cement mortar 1:2, plugs, wooden, in (Group 6 category A) timber 4" long, tapered 3" to 2" square section, including making holes in walls, floor etc.
Prime cost of 1 1/4" dia: plastic bottle trap (Indian or equivalent, approved quality). Rs 350 ** (1854)
Prime cost of 1 1/2" dia: plastic bottle trap (Indian or equivalent, approved quality). Rs 400 ** (1855)
Prime cost of 2" dia: plastic bottle trap (Indian or equivalent, approved quality). Rs 700 ** (1856)
Prime cost of 1 1/4" dia: bottle trap stainless steel (Approved quality). Rs2,200 ** (1857)
Prime cost of 1 1/2" dia: bottle trap stainless steel (Approved quality). Rs. 2,400 ** (1858)
Supplying and fixing PVC, P-Trap (2" dia.)
Prime cost of bib tap, 1/2" dia: brass .(Chinese or equivalent, approved quality) Rs 550 ** (1592)
BSR 2014- Department of Buildings
S07- 252
Description Item Unit
Supplying & fixing 1/2" dia. bib tap with long body chromium plated. (Approved quality)Nos
Supplying and fixing 1/2" dia: chromium plated bib tap imported (Duro) Nos
Bib Taps (Plastic)Supplying & fixing Plastic Bib Tap ½" dia. (T- Handle) (S-Lon or Equivalent.)
Nos
Supplying & fixing Plastic Bib Tap ½" dia. (Round- Handle)(S-Lon or Equivalent.) Nos
Supplying & fixing Plastic Bib Tap ¾" dia. (T- Handle) (S-Lon or Equivalent.) Nos
Supplying & fixing Plastic Bib Tap ¾" dia. (Round- Handle)(S-Lon or Equivalent.) Nos
Supplying & fixing Plastic long, Neck Bib Tap ½" dia. (T- Handle) (S-Lon or Equivalent.) Nos
Nos
Swan-Neck tap-(Metallic)Supplying & fixing chromium plated swan-neck tap ½" (Plumber) with necessary specials.
Nos
Swan-Neck tap-(Plastic)Supplying & fixing Plastic Swan- tap ½" dia. (T- Handle) (S-Lon or Equivalent.)
Nos
Supplying & fixing Plastic Swan-Neck tap ½" dia. (Round- Handle)(S-Lon or Equivalent.) Nos
Prime cost of, chromium plated bib tap 1/2" . (Plumber or Equivalent.) Rs1850 ** (1593)
Prime cost of 1/2" dia. bib tap with long body chromium plated.(Approved quality) Rs 2,100 ** (1876)
Prime cost of 1/2" dia: chromium plated bib tap imported.(Duro) Rs 2468 ** (1840)
Prime cost of bib tap, Plastic Bib Tap ½" dia. (T- Handle) (S-Lon or Equivalent.) Rs 161 ** (2532)
Prime cost of Plastic Bib Tap ½" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 211 ** (2533)
Prime cost of bib tap, Plastic Bib Tap ¾" dia. (T- Handle) (S-Lon or Equivalent.) Rs 239 ** (2534)
Prime cost of Plastic Bib Tap ¾" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 313 ** (2535)
Prime cost of bib tap, Plastic Bib Tap long Neck ½" dia. (T- Handle) (S-Lon or Equivalent.) Rs 227 ** (2536)
Supplying & fixing Plastic Bib Tap, long Neck ½" dia. (Round- Handle)(S-Lon or Equivalent.)
Prime cost of Plastic Bib Tap long Neck ½" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 259 ** (2537)
Prime cost of 1/2" dia: Chromium plated swan-neck tap ½" (Plumber) Rs 3360 ** (1829)
Prime cost of bib tap, Plastic Swan- tap ½" dia. (T- Handle) (S-Lon or Equivalent.) Rs 609 ** (2550)
BSR 2014- Department of Buildings
S07- 253
Description Item Unit
Prime cost of Plastic Swan-Neck tap ½" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 850 ** (2551)
BSR 2014- Department of Buildings
S07- 254
Description Item Unit
Chromium plated angle Taps/Valves 1/2"
Nos
Nos
Angle Taps/Valves (Plastic)Supplying & fixing Plastic Angle Tap ½" dia. (T- Handle) (S-Lon or Equivalent.)
Nos
Supplying & fixing Plastic Angle ½" dia. (Round- Handle)(S-Lon or Equivalent.) Nos
Chromium plated basin tap 1/2"Nos
Push tapsSupplying & fixing push taps 1/2" Brass, Becks, or equivalent approved quality.
NosSupplying & fixing push taps, 1/2" Brass, light pattern. NosStop tap. (Imported approved quality)
NosStop Taps (Plastic)
Nos
Nos
Nos
Nos
Supplying & fixing chromium plated angle tap 1/2" with necessary specials, imported, approved quality. (Duro or equivalent).
Prime cost of Chromium plated Angle valve(Duro) ½" dia. Rs 1840 ** (1830)
Supplying & fixing chromium plated angle tap 1/2" with necessary specials, imported, approved quality. (Indian or equivalent).
Prime cost of Chromium plated Angle valve(Plumber) ½" dia. Rs 1400 ** (1831)
Prime cost of bib tap, Plastic Angle ½" dia. (T- Handle) (S-Lon or Equivalent.) Rs 265 ** (2546)
Prime cost of Plastic Angle ½" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 253 ** (2547)
Supplying and fixing basin tap.(Twyford or equivalent approved quality)Prime cost of basin tap.(Twyford ) Rs 3500 ** (2171)
Supplying & fixing 1/2" dia. chromium plated stop tap. (Imported approved quality, concealed type)
Supplying & fixing Plastic Stop Taps ½" dia. (T- Handle) (S-Lon or Equivalent.)
Prime cost of bib tap, Plastic Stop Taps ½" dia. (T- Handle) (S-Lon or Equivalent.) Rs 159 ** (2540)
Supplying & fixing Plastic Stop Taps ½" dia. (Round- Handle)(S-Lon or Equivalent.)
Prime cost of Plastic Stop Taps ½" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 218 ** (2541)
Supplying & fixing Plastic Stop Taps ¾" dia. (T- Handle) (S-Lon or Equivalent.)
Prime cost of bib tap, Plastic Stop Taps ¾" dia. (T- Handle) (S-Lon or Equivalent.) Rs 309 ** (2542)
Supplying & fixing Plastic Stop Taps ¾" dia. (Round- Handle)(S-Lon or Equivalent.)
Prime cost of Plastic Stop Taps ¾" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 373 ** (2543)
BSR 2014- Department of Buildings
S07- 255
Description Item Unit
Nos
Nos
Bath tub tapS/F 3/4" dia. bath tub tap chromium plated, imported approved quality. NosGarden Taps (brass)
NosGarden Taps (Plastic)Supplying & fixing Plastic Garden Tap ½" dia. (T- Handle) (S-Lon or Equivalent.)
Nos
Supplying & fixing Plastic Garden Tap ½" dia. (Round- Handle)(S-Lon or Equivalent.) Nos
Pillar cocksRepairing pillar cocks, fixing to Basin carefully without making any damage to Basin.
NosSupplying & fixing pillar cocks 1/2" Chromium plated, to basins. (Plumber or equivalent)
NosPillar tapsSupplying and fixing 1/2" dia: chromium plated Pillar tap. (American Standard or Equivalent.)
Nos
Supplying & fixing 3/4" Chromium plated pillar Cock, to baths. ,(Plumber or equivalent) Nos
Basin Piller Taps (Plastic)Supplying & fixing Plastic Basin Piller tap ½" dia. (Round- Handle)(S-Lon or Equivalent.)
Nos
Stop cockSupplying & fixing stop cock, brass 1/2" dia. NosSupplying & fixing stop cock, brass 3/4" dia. NosSupplying & fixing stop cock, brass 1" dia. NosSupplying & fixing stop cock, brass 1 1/4" dia. Nos
Supplying & fixing Plastic Stop Taps 1" dia. (T- Handle) (S-Lon or Equivalent.)
Prime cost of bib tap, Plastic Stop Taps 1" dia. (T- Handle) (S-Lon or Equivalent.) Rs 431 ** (2544)
Supplying & fixing Plastic Stop Taps 1" dia. (Round- Handle)(S-Lon or Equivalent.)
Prime cost of Plastic Stop Taps 1" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 498 ** (2545)
Supplying & fixing garden tap 1/2" dia: brass, heavy quality, with necessary specials, imported, approved quality.
Prime cost of bib tap, Plastic Garden Tap ½" dia. (T- Handle) (S-Lon or Equivalent.) Rs 218 ** (2538)
Prime cost of Plastic Garden Tap ½" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 253 ** (2539)
Prime cost of Chromium plated Pillar tap, 1/2" dia:. (American Standard) Rs. 2,856 ** (2664)
Prime cost of Chromium plated Pillar tap, 3/4" dia. (Plumber or equivalent) Rs.1,800 ** 1636
Prime cost of Plastic Basin Piller tap ½" dia. (Round- Handle) (S-Lon or Equivalent.) Rs 479 ** (2548)
BSR 2014- Department of Buildings
S07- 256
Description Item Unit
Supplying & fixing stop cock, brass 1 1/2" dia. NosSupplying & fixing stop cock, brass 2" dia. NosSupplying & fixing stop cock, chromium plated 1/2" dia . NosConnector, G.ISupplying and fixing connector G.I 1/2". NosSupplying and fixing connector, G.I 3/4". NosSupplying and fixing connector, G.I 1". NosSupplying and fixing connector G.I 1 1/4". NosSupplying and fixing connector G.I 1 1/2". NosSupplying and fixing connector G.I 2". NosSupplying and fixing connector G.I 3". NosFixing connector, any size up to 1 1/2" (Fixing only) NosFixing connector, above 1 1/2" and up to 3" (Fixing only) NosSupplying and fixing cover and seat for pedestal closets in Teak including polishing.
NosSupplying & fixing cover and seat for pedestal closets in plastic. NosElbow, G.ISupplying and fixing elbow, G.I 1/2". NosSupplying and fixing elbow G.I 3/4". NosSupplying and fixing elbow G.I 1". NosSupplying and fixing elbow G.I 1 1/4". NosSupplying and fixing elbow G.I 1 1/2". NosSupplying and fixing elbow G.I 2". NosCleaning flushing cistern C.I 2 gallons and painting one coat of anti-corrosive paint internally.
Nos
NosFixing flushing Cistern complete (cistern & brackets available) NosSupplying & fixing flushing Cistern, low level, porcelain ,approved quality complete.
Nos
Nos
Nos
NosFlush pipe of pedestal closets, re-joining with yarn and putty after removing old putty etc.
NosFlush pipe G.I fixing, including soldering joints, (Fixing only) NosFlush pipe, G.I supplying and fixing complete. NosHooks for pipesHooks for 1/2" pipes, supplying and fixing. NosHooks for 3/4" pipes, supplying and fixing. NosHooks for 1" pipes, supplying and fixing. NosHooks for 1 1/4" pipes, supplying and fixing. NosHooks for 1 1/2" pipes, supplying and fixing. Nos
Supplying & fixing flushing cistern, C.I 2 gallons, existing flush pipe and brackets etc. including ball valve.
Fitting in position in cistern flushing cistern lever forged out of wrought iron, 1" x 3/16" approx. 1ft 6" long bent to shape, drilled at both ends.
Flushing cistern, disconnecting and plugging water connection and making good all damage to wall floors etc.
Flushing cistern, removing and re-fixing in new position including necessary plugs, and making good to walls.
BSR 2014- Department of Buildings
S07- 257
Description Item Unit
Hooks for pipes, available, fixing. NosJam NutsJam Nuts, G.I 1/2" supplying and fixing. NosJam Nuts, G.I 3/4" supplying and fixing. NosJam Nuts, G.I 1" supplying and fixing. NosJam Nuts, G.I 1 1/4" supplying and fixing. NosJam Nuts, G.I 1 1/2" supplying and fixing. NosJam Nuts, G.I 2" supplying and fixing. NosJam Nuts, any size up to 2" fixing (Jam Nut available). NosNipples, G.INipples, G.I 1/2" Supplying & fixing. NosNipples, G.I 3/4" Supplying & fixing NosNipples, G.I 1" Supplying & fixing. NosNipples, G.I 1 1/4" Supplying & fixing. NosNipples, G.I 1 1/2" Supplying & fixing. NosNipples, G.I 2" Supplying & fixing. NosNipples, any size up to 2" fixed. (Nipple available). NosPipes G.I
L.ft
L.ft
L.ft
L.ft
L.ft
L.ft
L.ft
L.ft
L.ft
L.ft
Pipes G.I 1/2" supplying and fixing (fittings to be paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls (pipe hooks to be paid for separately)
Pipes G.I 3/4" supplying and fixing (fittings to be paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls (pipe hooks to be paid for separately).
Pipes, G.I 1" supplying and fixing (fittings to be paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls. (Pipe hooks to be paid for separately)
Pipes, G.I 1 1/4" supplying and fixing (fittings to be paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls. (Pipe hooks to be paid for separately)
Pipes, G.I 1 1/2" supplying and fixing (fittings to be paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls. (Pipe hooks to be paid for separately)
Pipes, G.I 2" supplying and fixing (fittings paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls. (Pipe hooks to be paid for separately)
Pipes, G.I 2 1/2" supplying and fixing (fittings paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls. (Pipe hooks to be paid for separately)
Pipes, G.I 3" supplying and fixing (fittings to be paid for separately) including any necessary trenching, backfilling and making good, or fixing to walls. (Pipe hooks to be paid for separately)
Pipes, G.I 1/2" to 2" fixing complete with specials such as bends, elbows etc. (pipes and specials available)
Pipes, G.I 2 1/2" to 3" fixing complete with specials such as bends, elbows etc. (pipes and specials available)
BSR 2014- Department of Buildings
S07- 258
Description Item Unit
Pipes, G.I any size up to 2" removing and trench filling in. L.ftPipes, G.I 4" dia. removing, and walls floors etc. making good. L.ftPipes, G.I existing, taking out, cleaning and relaying, any size up to 2" including backfilling.
L.ftPipes, G.I 2 1/2" to 3" taking out, cleaning & relaying including backfilling.
L.ft
L.ftPipe joints, lead making good including soldering. Nos
L.ft
NosPlugs, G.I any size fixing (Plug available) NosPlugs, G.I 1/2" supplying and fixing. NosPlugs, G.I 3/4" supplying and fixing. NosPlugs, G.I 1" supplying and fixing. NosPlugs, G.I 1/4" supplying and fixing. NosPlugs, G.I 1 1/2" supplying and fixing. NosPlugs, G.I 2" supplying and fixing. NosSocket G.I Socket G.I 1/2" plain supplying & fixing. NosSocket, G.I 3/4" plain supplying and fixing. NosSocket, G.I 1" plain supplying and fixing. NosSocket, G.I 1 1/4" plain supplying and fixing. NosSocket, G.I 1 1/2" plain supplying and fixing. NosSocket, G.I 2" plain supplying and fixing. NosSocket, G.I 3" plain supplying and fixing. NosSocket, G.I reducing 3/4" to smaller sizes supplying and fixing. NosSocket, G.I reducing 1" to smaller size supplying and fixing. NosSocket, G.I reducing 1 1/4" to smaller sizes supplying and fixing. NosSocket, G.I reducing 1 1/2" to smaller sizes supplying and fixing. NosSocket G.I reducing 2" to smaller sizes, supplying and fixing. NosSockets G.I reducing 3" to smaller sizes supplying and fixing. NosSocket G.I any size fixing (socket available). Nos R.S.J 's as supports for tanks
cwtRemoving tank G.I
Nos
Pipes, G.I existing, any size up to 2" taking out, cleaning and relaying in new position, including backfilling.
Pipes, outlet, up to 8ft 0" cleaning, (removing & relaying where necessary will be paid for separately) assume 2ft 0" length
Pipes, underground, leaks repairing, including necessary trenching and backfilling (pipes or fittings to be used in repairs paid for separately)
Supplying & fixing in position steel work in R.S.J ' s as supports for tanks, up to 20' 0" height and painting 2 coats anti-corrosive paint.
Removing tank G.I, 25 to 200 gls. on existing supports up to 20' 0" height and connecting to existing pipes including disconnecting and taking down old tank and painting new tank 2 coats anticorrosive paint. (Tank available and scaffolding paid separately)
BSR 2014- Department of Buildings
S07- 259
Description Item Unit
NosFixing tank, G.I
Nos
NosClearing & washing tankClearing & washing tank, storage, up to 400 gals capacity. NosCleaning & washing tank, storage, over 400 gals. Capacity. Nos
NosPlastishell (Single Layer) water tank
Nos
Nos
Nos
NosPlastishell (Triple Layer) water tank
Nos
Nos
Nos
Nos
Nos
Removing tank G.I. 250 to 400 gls. on existing supports up to 20' 0" height and connecting to existing pipes including disconnecting and taking down old tank and painting new tank 2 coats anticorrosive paint. (Tank available and scaffolding paid separately)
Fixing tank, G.I 25 - 250 gals. with overflow washout and stop cock, fixed on R.S joists and painted 2 coats of anticorrosive paint & connecting to supply and delivery pipes, (Tank fittings, pipes and R.S.J will be paid for separately).
fixing tank, G.I. 250 - 400 gals. with overflow washout and stop cock, fixed on R.S joists and painting 2 coats of anticorrosive paint connecting to supply and delivery pipes, (Tank fittings, pipes and R.S.J will be paid for separately).
Removing tank, storage, G.I and walls made good (scaffolding will be paid for separately where necessary).
Supplying and fixing Plastishell (Single Layer) water tank 250 liter capacity. ( fittings paid for separately ).
Supplying and fixing Plastishell (Single Layer) water tank 500 liter capacity. ( fittings paid for separately ).
Supplying and fixing Plastishell (Single Layer) water tank 750 liter capacity. ( fittings paid for separately ).
Supplying and fixing Plastishell (Single Layer) water tank 1000 liter capacity. ( fittings paid for separately ).
Supplying and fixing Plastishell (Triple Layer) water tank, 110 Gal. (500 lit.) capacity.( fittings paid for separately ).
Prime cost of Water tank 500lit. Plastishell (Triple Layer).Rs.10,680 ** (2482)
Supplying and fixing Plastishell (Triple Layer) water tank, 220 Gal. (1000 lit.) capacity. ( fittings paid for separately ).
Prime cost of Water tank 1000lit. Plastishell (Triple Layer).Rs.18,233 ** (2484)
Supplying and fixing Plastishell (Triple Layer) water tank, 440 Gal. (2000 lit.) capacity. ( fittings paid for separately ).
Prime cost of Water tank 2000 lit. Plastishell (Triple Layer).Rs.34,760 ** (2485)
Supplying and fixing Plastishell (Triple Layer) water tank, 1155 Gal. Or ( 5250 liter) capacity. ( fittings paid for separately ).
Prime cost of Water tank 5250 liter Plastishell (Triple Layer).Rs.68,250 ** (2486)
Supplying and fixing Plastishell (Triple Layer) water tank, 2310 Gal. or (10500 liter) capacity. ( fittings paid for separately ).
BSR 2014- Department of Buildings
S07- 260
Description Item Unit
Floater switchSupplying and fixing floater switch with necessary fittings to over head water tank.
Nos
TeesTees, G.I 1/2" equal supplying and fixing. NosTees, G.I 3/4" equal supplying and fixing. NosTees, G.I 1" equal supplying and fixing. NosTees, G.I 1 1/4" equal supplying and fixing. NosTees, G.I 1 1/2" equal supplying and fixing. NosTees, G.I 2" equal, supplying and fixing. NosTrapsTrap, lead fixed in position with one wipe joint (Trap available). NosTrap lead, 1 1/4" supplying and fixing with one wipe joint. NosTrap lead 1 1/2" supplying and fixing with one wipe joint. NosTrap, lead 2" supplying and fixing with one wipe joint. NosTrap, lead 1" to 2" soldering and refixing. NosBath room accessories (Total Set)
Nos Tumbler holderSupplying & fixing tumbler holder, chromium plated, to wall with rawl plugs.
Nos
Soap tray/dishSupplying & fixing soap tray, white porcelain, to wall with rawl plugs. Nos
Supplying and fixing chromium plated soap tray. Nos
Supplying and fixing soap dish (American Standard or Equivalent.) Nos
Soap dispenser
Nos
Shelves, plate glass
Nos
Prime cost of Water tank 10,500lit. Plastishell (Triple Layer).Rs.120,225 ** (2487)
Prime cost of floater switch Rs.1500 ** (2205)
Supplying & fixing set of bath room accessories such as toilet paper holder, soap tray, tooth brush holder, towel bar and rings ,Bath room glass shelves etc. with necessary materials, Local and approved quality.
Prime cost of Tumbler holder, chromium plated, (Indian).Rs.800 ** (1716)
Prime cost of Soap tray, white porcelain,(Indian).Rs.500 ** (1689)
Prime cost of Chromium plated soap tray(American Standard).Rs.5096 ** (1838)
Prime cost of Soap dish (American Standard).Rs.2072 ** (2630)
Supplying & fixing soap dispenser (American Standard or Equivalent.), white porcelain, to wall with rawl plugs.
Prime cost of Soap dispenser (American Standard).Rs.4704 ** (2662)
Supplying & fixing shelves, plate glass 24" x 5" with chromium plated brackets to wall with Rawl Plugs.
BSR 2014- Department of Buildings
S07- 261
Description Item Unit
Towel rail
Nos
Nos
Paper holder SEVA
Nos
Tooth brush holderSupplying & fixing tooth brush holder, Chromium plated to wall with rawl plugs.
Nos
Nos
Robe hook (SEVA)
Nos
Bath room mirror,
Nos
Nos
NosShower rose-Fixing OnlyFixing shower rose, any size (shower rose Paid separately). Nos
Prime cost of Shelves, plate glass 24" x 5" with chromium plated brackets.Rs.500 ** (1667)
Supplying & fixing chromium plated towel rail (Indian), 2ft 0" long and , ¾" dia. with necessary rawl plugs and screws.
Prime cost of chromium plated towel rail (Indian) , 2ft 0" long and , ¾" dia. Width.Rs.1,100 ** (1837)
Supplying & fixing chromium plated Towel rail (American Standard or Equivalent.-S. No:6588) , 2ft 0" long and , ¾" dia. with necessary rawl plugs and screws.
Prime cost of chromium plated Towel rail (American Standard)-(No:6588) , 2ft 0" long and , ¾" dia. Width. Rs .3,080 ** (2661)
Supplying & fixing SEVA paper holder (American Standard or Equivalent.) complete to working order.
Prime cost of SEVA paper holder (American Standard).Rs 2,408 ** (2628)
Prime cost of Tooth brush holder, Chromium plated(Indian).Rs 600 ** (1715)
Supplying & fixing tooth brush holder (American Standard or Equivalent.) complete to working order.
Prime cost of Tooth brush holder (American Standard)-(S.No:6582), Rs. 2 072 ** (2629)
Supplying & fixing SEVA Robe hook (American Standard or Equivalent.) complete to working order.
Prime cost of SEVA Robe hook (American Standard).Rs 1,792 ** (2631)
Supplying & fixing mirror, beveled, bath room type, oval shape, 20" x 16" Max. and min. dimensions, to wall with Rawl plugs and chromium plated fittings.
Prime cost of mirror, beveled, bath room type, oval shape, 20" x 16" -Rs 2,400 ** (1626)
Supplying & fixing 24" x 18", 5mm thickness beveled rectangular mirror, to wall with Rawl plugs, noton tape and chromium plated fittings.
Prime cost of mirror, beveled, bath room type, rectangular shape, 24" x 18", 5mm thickness -Rs 3,250 ** (1628)
Supplying and fixing toilet mirror cabinet with necessary rawl plugs and screws etc.( D 1003 s/s)
BSR 2014- Department of Buildings
S07- 262
Description Item Unit
Shower roseSupplying & fixing Shower rose, 6" copper. NosSupplying & fixing shower Rose 7" chromium plated. NosSoldering and refixing shower Rose. NosSupplying & fixing PVC- 6" x 1/2" shower rose. NosPlastic Jet Shower roseSupplying & fixing Plastic Jet Shower Rose ½" dia. (S-Lon or Equivalent.)
Nos
NosSupplying & fixing Jet shower complete(American Standard or Equivalent.)
Prime cost of Jet shower imported (American Standard).Rs 2,016 ** (1873)
BSR 2014- Department of Buildings
S07- 263
Description Item Unit
Shower headSupplying & fixing Shower head with arm. (American Standard) Nos
Bidet spray importedSupplying and fixing bidet spray imported Indian or equivalent. Nos
Supplying and fixing bidet spray imported (Grohe or equivalent ). Nos
AccessoriesSupplying & fixing chain, chromium plated, for bath or basin, with plug. NosSupplying & fixing chain pulls, chromium plated, for flushing cistern. NosFixing bends, elbows and tees- Workmanship onlyFixing bends, elbows and tees and other specials of P.V.C size 3".(Workmanship only).
NosBends P.V.CSupplying & fixing bends P.V.C 1/2". NosSupplying & fixing bends P.V.C 3/4". NosSupplying & fixing bends P.V.C 1". NosSupplying & fixing bends P.V.C 1 1/4". NosSupplying & fixing bends P.V.C 1 1/2". NosSupplying & fixing bends P.V.C 2". NosSupplying & fixing bends P.V.C 3". NosElbows P.V.CSupplying & fixing elbows P.V.C 1/2". NosSupplying & fixing elbows P.V.C 3/4". NosSupplying & fixing elbows P.V.C 1". NosSupplying & fixing elbows P.V.C 1 1/4". NosSupplying & fixing elbows P.V.C 1 1/2". NosSupplying & fixing elbows P.V.C 2". NosSupplying & fixing elbows P.V.C 3". NosReducing sockets & Tees P.V.CSupplying & fixing sockets reducing P.V.C (3/4"x1/2" ) to smaller sizes. NosSupplying & fixing sockets reducing P.V.C (1" x3/4") to smaller sizes. NosSupplying & fixing sockets reducing P.V.C (1 1/4"x1") to smaller sizes. NosSupplying & fixing sockets reducing P.V.C (1 1/2" x1 1/4") to smaller sizes.
NosSupplying & fixing sockets reducing P.V.C (2" x1") to smaller sizes. NosSupplying & fixing sockets reducing P.V.C (2" x1 1/2") to smaller sizes.
NosReducing Tees P.V.CSupplying & fixing tees reducing P.V.C (3/4"x1/2" ) to smaller sizes. NosSupplying & fixing tees reducing P.V.C (1" x3/4") to smaller sizes. NosSupplying & fixing tees reducing P.V.C (1 1/4"x1") to smaller sizes. NosSupplying & fixing tees reducing P.V.C (1 1/2" x1 1/4") to smaller sizes.
Nos
Prime cost of Shower head with arm (American Standard).Rs 2,200 ** (2663)
Prime cost of Bidet spray ( Indian) .Rs 1,500 ** (2057)
Prime cost of Bidet spray ( Grohe) .Rs 3,400 ** (2058)
BSR 2014- Department of Buildings
S07- 264
Description Item Unit
Supplying & fixing tees reducing P.V.C (2" x1 1/2") to smaller sizes. NosSupplying & fixing tees reducing P.V.C (3" x 2") to smaller sizes. NosSupplying & fixing reducing tee P.V.C. ( 4" - 2") NosRepair Sockets & Tees P.V.CSupplying & fixing repair socket P.V.C 1/2". NosSupplying & fixing repair socket P.V.C 3/4". NosSupplying & fixing repair socket P.V.C 1". NosSupplying & fixing repair socket P.V.C 1 1/4". NosSupplying & fixing repair socket P.V.C 1 1/2". NosSupplying & fixing repair socket P.V.C 2". NosSupplying & fixing repair socket P.V.C 3". NosValve Socket P.V.CSupplying & fixing valve socket P.V.C 1/2". NosSupplying & fixing valve socket P.V.C 3/4". NosSupplying & fixing valve socket P.V.C 1". NosSupplying & fixing valve socket P.V.C 1 1/4". NosSupplying & fixing valve socket P.V.C 1 1/2". NosSupplying & fixing valve socket P.V.C 2". NosSupplying & fixing valve socket P.V.C 3". NosFaucet Socket P.V.CSupplying & fixing faucet sockets P.V.C 1/2". NosSupplying & fixing faucet sockets P.V.C 3/4". NosSupplying & fixing faucet sockets P.V.C 1". NosSupplying & fixing faucet sockets P.V.C 1 1/4". NosSupplying & fixing faucet sockets P.V.C 1 1/2". NosSupplying & fixing faucet sockets P.V.C 2". P NosSupplying & fixing faucet sockets P.V.C 3". NosTapered union without thread P.V.C Supplying & fixing tapered union without thread P.V.C 1/2". NosSupplying & fixing tapered union without thread P.V.C 3/4". NosSupplying & fixing tapered union without thread P.V.C 1". NosSupplying & fixing tapered union without thread P.V.C 1 1/4". NosSupplying & fixing tapered union without thread P.V.C 1 1/2". NosSupplying & fixing tapered union without thread P.V.C 2". NosSupplying & fixing tapered union without thread P.V.C 3". NosSupplying & fixing tapered union with thread for P.V.C and metal pipe connection 1/2".
NosSupplying & fixing tapered union 3/4" with thread for P.V.C & metal pipe connections.
NosSupplying & fixing tapered union 1" with thread for P.V.C & metal pipe connections.
NosSupplying & fixing tapered union 1 1/4" with thread for P.V.C & metal pipe connections.
NosSupplying & fixing tapered union 1 1/2" with thread for P.V.C & metal pipe connections.
Nos
BSR 2014- Department of Buildings
S07- 265
Description Item Unit
Supplying & fixing tapered union 2" with thread for P.V.C & metal pipe connections. Nos
Supplying & fixing tapered union 3" with thread for P.V.C & metal pipe connections. Nos
BSR 2014- Department of Buildings
S07- 266
Description Item Unit
Equal tees-P.V.CSupplying & fixing tees equal P.V.C 1/2". NosSupplying & fixing tees equal P.V.C 3/4". NosSupplying & fixing tees equal P.V.C 1". NosSupplying & fixing tees equal P.V.C 1 1/4". NosSupplying & fixing tees equal P.V.C 1 1/2". NosSupplying & fixing tees equal P.V.C 2". NosSupplying & fixing tees equal P.V.C 3". NosPlugs, sockets-P.V.CSupplying & fixing plugs P.V.C 1/2". NosSupplying & fixing plugs P.V.C 3/4". NosSupplying & fixing plugs P.V.C 1". NosSupplying & fixing plugs P.V.C 1 1/4". NosSupplying & fixing plugs P.V.C 1 1/2". NosSupplying & fixing Plugs P.V.C 2". NosSupplying & fixing plugs P.V.C 3". NosSupplying & fixing sockets plain P.V.C 1/2". NosSupplying & fixing sockets plain P.V.C 3/4". NosSupplying & fixing sockets plain P.V.C 1". NosSupplying & fixing sockets plain P.V.C 1 1/4". NosSupplying & fixing sockets plain P.V.C 1 1/2". NosSupplying & fixing sockets plain P.V.C 2". NosSupplying & fixing sockets plain P.V.C 3". NosPipes P.V.CSupplying & fixing pipes P.V.C, 1/2" dia.(Type 1000)- PE.(Fittings paid separately).
L.ftSupplying & fixing pipes P.V.C, 3/4"dia.(Type 1000)- PE (Fittings paid separately).
L.ftSupplying & fixing pipes P.V.C, 1"dia. (Type 1000)- PE(Fittings paid separately).
L.ftSupplying & fixing pipes P.V.C, 1 1/4"dia. (Type 1000)- PE(Fittings paid separately).
L.ftSupplying & fixing pipes P.V.C 1 1/2"dia. (Type 1000)- PE (Fittings paid separately).
L.ftSupplying & fixing pipes P.V.C, 2"dia. (Type 1000)- PE (Fittings paid separately).
L.ftSupplying & fixing pipes P.V.C 3". (Type 1000)- PE (Fittings paid separately).
L.ftFixing pipesFixing pipes P.V.C, 1/2" to 2" dia. Complete with specials. (pipes & specials paid separately).
L.ftFixing pipes P.V.C, 2 1/2" to 3"dia. complete with specials. (pipes & specials paid separately).
L.ft
NosForming bends or jointing pipes by heating without fixing specials in rigid P.V.C, 1/2" to 1"dia. (Workmanship only).
BSR 2014- Department of Buildings
S07- 267
Description Item Unit
Nos
NosPipes P.V.C (25% pipe cost included for Specials)
L.ft
L.ft
L.ft
L.ft
L.ft
L.ftFlexible cord (S--Lon or Equivalent))Supplying and fixing flexible cord -12" (S-lon or equivalent) NosSupplying and fixing flexible cord -18" (S-lon or equivalent) NosSupplying and fixing flexible cord -24" (S-lon or equivalent) NosSupplying and fixing flexible cord -48" (S-lon or equivalent) NosSupplying and fixing flexible cord -60" (S-lon or equivalent) NosFlexible cord (Imported European)Supplying and fixing flexible cord 1ft -6" imported, approved quality. (Italy or equivalent).
NosSupplying and fixing flexible cord 1ft -0" imported, approved quality. (Italy or equivalent).
NosFlexible hoseSupplying and fixing 1/2" dia: Flexible hose (American Standard or Equivalent.)
Nos
Garden Watering Hose ½" dia.Supplying Garden Hose ½" dia. & 15m long (S-Lon or equivalent). NosSupplying Garden Hose ½" dia. & 30m long (S-Lon or equivalent). NosWater pump
Nos
NosSupplying and installation of "Jinasena" 1/2" dia. Water pressure pump Nos
Supplying and fixing 1" dia. pressure pump 110/A 18/1 (Centric type pumping unit)Nos
Forming bends or jointing pipes by heating without fixing specials in rigid P.V.C 1 1/4" to 2" dia.(Workmanship only).
Forming bends or jointing pipes by heating without fixing specials in rigid P.V.C, 2 1/2" to 3"dia. (Workmanship only).
Supplying & fixing pipes P.V.C, 1/2" dia. (Type 1000) including specials. (25% pipe cost included for Specials)
Supplying & fixing pipes P.V.C, 3/4"dia. (Type 1000) including specials. (25% pipe cost included for Specials)
Supplying & fixing pipes P.V.C, 1"dia. (Type 1000) including specials. (25% pipe cost included for Specials)
Supplying & fixing pipes P.V.C, 1 1/4"dia. (Type 1000) including specials. (25% pipe cost included for Specials)
Supplying & fixing pipes P.V.C, 1 1/2"dia. (Type 1000) including specials. (25% pipe cost included for Specials)
Supplying & fixing pipes P.V.C, 2"dia. (Type 1000) including specials. (25% pipe cost included for Specials)
Prime cost of Flexible hose (American Standard) Rs. 448 ** (2666)
Installing available 3/4"-1" water pump with necessary fittings, foot valve, concrete base, rag bolts etc.(concrete paid for separately)
Installing available 1 1/2"-2" dia. water pump with necessary fittings, concrete base and rag bolts.(concrete paid for separately).
Prime cost of Pressure pump (Br - 50) ,Jinasena" 1/2" dia. Rs.18,370 ** (2577)
BSR 2014- Department of Buildings
S07- 268
Description Item Unit
Electric water geyserReplacing available Electric water Geyser , making hot water Supply in order.
Nos
Nos
Nos
Nos
Nos
Nos
Plastic gullySupplying & fixing plastic gully grating 6"x6". Nos
NosShower tray fiberglassSupplying & fixing shower tray fiberglass 30" x 32" including waste plug & specials
Nos
Elbows for down pipe. Supplying & fixing or replacing, only a 3 1/2" P.V.C. elbows for down pipe.
NosRunning head. Supplying & fixing or replacing, only a P.V.C. running head. NosGutter end.Supplying & fixing or replacing, only a square type P.V.C. gutter ends. NosGutter Joint.Supplying & fixing or replacing, only a square type P.V.C. gutter joints. NosEves gutters (PVC)-Square type
L.ft
Prime cost of 1" dia. Centric pressure pump 110/A 18/1 ,Jinasena- 1" dia. Rs.34,532 ** (2576)
Supplying and fixing 50 Liter Electric water Geyser ( approved quality) on a wall or existing brackets and connected to the hot water supply system.(hot water piping system paid separately)
Prime cost of 50 Liter Electric water Geyser ( approved quality).Rs 24,500 ** (2574)
Supplying and replacing of Electric water geezer (water heater 30 lit.) imported quality. (Ariston or equivalent)
Prime cost of 30 Liter Electric water Geyser ( approved quality).Rs 22,500 ** (2575)
Supplying and fixing of instant water geezer (water booster pump) imported quality. (Singer or equivalent)
Prime cost of instant water Geyser ( approved quality).Rs 14,999 ** (2807)
Supplying and fixing of instant water geezer (water booster pump) imported quality. (Singer or equivalent)
Prime cost of instant water Geyser ( approved quality).Rs 16,999 ** (2808)
Supplying and fixing of instant water geezer (water booster pump) imported quality. (Singer or equivalent)
Prime cost of instant water Geyser ( approved quality).Rs 24,999 ** (2809)
Providing Catch pit 6"x6"x3" in cement mortar.
Prime cost of fiberglass shower tray 30" x 32" .Rs 7,000 ** (1887)
Supplying and fixing eves gutters square type PVC with necessary specials, including running heads, miter joints, gutter joints, gutter brackets, gutter ends etc.
BSR 2014- Department of Buildings
S07- 269
Description Item Unit
Supplying & fixing eave gutters 6" half-round P.V.C with P.V.C brackets. L.ft
Down pipes 3½" dia. P.V.C
L.ftSupplying & fixing rain water down pipes 3 ½" dia. P.V.C to wall, with necessary specials, including elbows, sockets, clips etc.
BSR 2014- Department of Buildings
S07- 270
Description Item Unit
R-DRAIN LAYERInterceptor, EarthenwareInterceptor, earthenware, 4" supplying and fixing. NosInterceptor, earthenware, 6" supplying and fixing. NosInterceptor, earthenware, 4" supplying and fixing. (Fixing only). NosManhole- brick in cement
Nos
Nos
Nos
Nos
Nos
Nos
Nos
Nos
Nos
Nos
Manhole 2ft x 2ft and up to 2ft 0" deep, 9" thick brick in cement 1:3 walls and cement rendering 1/2" (1:2) with 6" cement concrete foundation 1:3:6(2" metal) including forming channels, but without cover.
Manhole 3ft 6" x 2ft 3" and 2ft 0" to 4ft 0" deep 9" thick brick in cement 1:3 walls and cement rendering 1/2" (1:2) with 6" cement concrete foundation 1:3:6(2" metal) including forming channels, but without cover.
Manhole 3ft 6" x 2ft 3" and 4ft 0" to 6ft 0" deep, 9" thick brick in cement 1:3 walls and cement rendering 1/2" (1:2) with 6" cement concrete foundation 1:3:6 (2" metal) including forming channels, but without cover.
RCC Manhole (Type A)- [As per Drg.No 2013-TP-ST06 & ST07]RCC Manhole type A, Internal dimensions 475 x 625mm (depth up to 450mm) wall thickness 150mm & base Slab thickness 150mm. (Cover Slab & Inlet / Outlet Connections Paid for Separately) Single R/F
RCC Manhole type A, Internal dimensions 475 x 625mm (Depth is greater than 450mm & up to 600mm) wall thickness 187.5 mm & base Slab thickness 175 mm. (Cover Slab & Inlet / Outlet Connections Paid Separately) Double R/F
RCC Manhole type , Internal dimensions A- 475 x 625mm (Depth is greater than600mm & upto750 mm) wall thickness 187.5mm & base Slab thickness 175 mm. (Cover Slab & Inlet / Outlet Connections Paid for Separately) Double R/F
RCC Manhole type A, Internal dimensions 475 x 625mm (Depth is greater than 750mm & up to 900mm) wall thickness 187.5mm & base Slab thickness 175mm. (Cover Slab & Inlet / Outlet Connections Paid for Separately) Double R/F
RCC Manhole (Type B)- [As per Drg.No 2013-TP-ST06]RCC Manhole type B ,Internal dimensions 475 x 750mm (depth up to 450mm)wall thickness 150 mm & base Slab thickness 150 mm.(Cover Slab & Inlet / Outlet Connections Paid Separately) Single R/F
RCC Manhole type B - 475 x 750mm internally (Depth is greater than 450mm & up to 600mm) wall thickness 175 mm & base Slab thickness 175mm. (Cover Slab & Inlet / Outlet Connections Paid Separately) Double R/F
RCC Manhole type B- 475 x 750mm internally (Depth is greater than600mm & upto750 mm) wall thickness 175 mm & base Slab thickness 175mm. (Cover Slab & Inlet / Outlet Connections Paid Separately) Double R/F
BSR 2014- Department of Buildings
S07- 271
Description Item Unit
Nos
RCC Manhole type B, Internal dimensions 475 x 750mm internally (Depth is greater than 750mm & up to 900mm) wall thickness 175 mm & base Slab thickness 175mm. (Cover Slab & Inlet / Outlet Connections Paid Separately) Double R/F
BSR 2014- Department of Buildings
S07- 272
Description Item Unit
Nos
Nos
Nos
NosManhole cover, reinforced concrete
NosManhole cover, Cast IronManhole cover C.I rectangular, above 1 cwt. supplying and fixing. Nos
NosCast iron grating
NosWire dome (Steel)Wire domes for 2" pipes supplying and fixing. NosWire domes for 4" pipes supplying and fixing. NosWire dome (Copper)Supplying & fixing copper wire dome for 2" dia. P.V.C drainage pipes. NosSupplying & fixing copper wire dome for 4" dia. P.V.C drainage pipes. NosDrainage Fittings 4" (110mm) dia-(Local make)Supplying & fixing 4" dia. P.V.C plain socket (Local make) Nos
NosSupplying & fixing 4" dia. P.V.C drainage bend 45 degree. (S-Lon or Equivalent.)
Nos
NosSupplying & fixing 4" dia. P.V.C drainage bend 89 degree. (S-Lon or Equivalent.)
Nos
NosSupplying & fixing 4" dia. P.V.C drainage Tee. (S-Lon or Equivalent.) Nos
RCC Manhole (Type C)- [As per Drg.No 2013-TP-ST06]RCC Manhole type C- 475 x1050mm internally (Depth up to 450mm) wall thickness 100 mm & base Slab thickness 150 mm. (Cover Slab & Inlet / Outlet Connections Paid Separately) Single R/F
RCC Manhole type C , Internal dimensions 475 x1050mm (Depth is greater than 450mm & up to 600mm) wall thickness 175 mm & base Slab thickness 175 mm. (Cover Slab & Inlet / Outlet Connections Paid Separately) Double R/F
RCC Manhole type C, Internal dimensions 475 x1050mm internally(Depth is greater than600mm & upto750 mm) wall thickness 175 mm & base Slab thickness 175mm.. (Cover Slab & Inlet / Outlet Connections Paid Separately) Double R/F
RCC Manhole type C , Internal dimensions 475 x1050mm (Depth is greater than 750mm & up to 900mm) wall thickness 175 mm & base Slab thickness 175mm. (Cover Slab & Inlet / Outlet Connections Paid Separately) Double R/F
Manhole cover, reinforced concrete 3" thick 2ft 0" x 2ft 0" approx. supplying and fixing, reinforced with 1/4" dia. M.S. rods at 3" centers, both ways.
Manhole cover Ductile iron rectangular 2'X2', supplying and fixing. (heavy duty) 12.5 TON (Prime cost Rs.17,000)
Grating C.I, 6" x 6" supplying and fixing.
Supplying & fixing 4" dia. P.V.C drainage elbow with single Door, approved quality with rubber ring joint.(Locally made)
Supplying & fixing 4" dia. P.V.C drainage bend 45 degree ,with single Door (S-Lon or Equivalent.)
Supplying & fixing 4" dia. P.V.C drainage bend 89 degree. With single Door (S-Lon or Equivalent.)
BSR 2014- Department of Buildings
S07- 273
Description Item Unit
Supplying & fixing 4" dia. P.V.C drainage Swept Tee. (S-Lon or Equivalent.)Nos
Supplying & fixing 4" dia. P.V.C drainage Tee. with single Door (S-Lon or Equivalent.)Nos
Supplying & fixing 4" dia. P.V.C drainage Swept Tee. with single Door (S-Lon or Equivalent.)Nos
Supplying & fixing 4" dia. P.V.C drainage "Y" junction (S-Lon or Equivalent.)Nos
NosDrainage Fittings 2" (63mm) dia.Supplying & fixing 2" dia. P.V.C drainage bend 45 degree. (S-Lon or Equivalent.)
Nos
NosSupplying & fixing 2" dia. P.V.C drainage bend 89 degree. (S-Lon or Equivalent.)
Nos
NosSupplying & fixing 2" dia. P.V.C drainage Tee. (S-Lon or Equivalent.) NosSupplying & fixing 2" dia. P.V.C drainage Swept Tee. (S-Lon or Equivalent.)
NosSupplying & fixing 4" dia. P.V.C drainage Tee. with single Door (S-Lon or Equivalent.)
NosSupplying & fixing 2" dia. P.V.C drainage Swept Tee. with single Door (S-Lon or Equivalent.)
NosSupplying & fixing 2" dia. P.V.C drainage "Y" junction (S-Lon or Equivalent.)
Nos
NosDrainage Fittings 1½"or (50mm) diaSupplying & fixing 1½" dia. P.V.C drainage bend 45 degree. (S-Lon or Equivalent.)
Nos
NosSupplying & fixing 1½"" dia. P.V.C drainage bend 89 degree. (S-Lon or Equivalent.)
Nos
NosSupplying & fixing 1½"" dia. P.V.C drainage Tee. (S-Lon or Equivalent.)
NosSupplying & fixing 1½"" dia. P.V.C drainage Swept Tee. (S-Lon or Equivalent.)
NosSupplying & fixing 1½"" dia. P.V.C drainage Tee. with single Door (S-Lon or Equivalent.)
Nos
Supplying & fixing 4" dia. P.V.C drainage "Y" junction with single Door (S-Lon or Equivalent.)
Supplying & fixing 2" dia. P.V.C drainage bend 45 degree, with single Door (S-Lon or Equivalent.)
Supplying & fixing 2" dia. P.V.C drainage bend 89 degree, with single Door (S-Lon or Equivalent.)
Supplying & fixing 2" dia. P.V.C drainage "Y" junction with single Door (S-Lon or Equivalent.)
Supplying & fixing 1½" dia. P.V.C drainage bend 45 degree with single Door (S-Lon or Equivalent.)
Supplying & fixing 1½"" dia. P.V.C drainage bend 89 degree, with single Door (S-Lon or Equivalent.)
BSR 2014- Department of Buildings
S07- 274
Description Item Unit
NosSupplying & fixing 1½" dia. P.V.C drainage "Y" junction (S-Lon or Equivalent.)
Nos
NosPipes P.V.C, 4"(110mm) dia, (type 250)-(Vent pipes fixed to walls)
L.ftPipes P.V.C, 4"(110mm)dia, (type 400)-(Vent pipes fixed to walls)
L.ftPipes P.V.C, 4"(110mm) dia, (type 400)- lay in Trenches
L.ft
L.ft
L.ftDrain Pipes P.V.C, 4" dia, (type 600)- lay in Trenches
L.ft
L.ft
L.ftDrain Pipes P.V.C, 6" dia, (type 600)- lay in Trenches
L.ft
L.ft
L.ftDrain Pipes P.V.C, 12" dia, (type 600)
Supplying & fixing 1½"" dia. P.V.C drainage Swept Tee. with single Door (S-Lon or Equivalent.)
Supplying & fixing 1½" dia. P.V.C drainage "Y" junction with single Door (S-Lon or Equivalent.)
Supplying & fixing 4" dia. (type 250) P.V.C pipes as vent pipes fixed to walls with necessary wooden plugs and P.V.C saddles at 4ft centers.
Supplying & fixing 4" dia. (type 400) P.V.C pipes, as drainage pipes fixed to walls with necessary wooden plugs, brass screws & saddles at 4ft centers.
Pipes P.V.C, 4" dia, (type 400) laying on cement concrete 6" thick up to 2ft 0" depth of invert including excavation and cement concrete hunching (1:3:6(1")).
Pipes P.V.C, 4" dia, (type 400) laying on cement concrete 6" thick over 2 ft. up to 4 ft. depth of invert including excavation and cement concrete hunching (1:3:6(1")).
Drains P.V.C, 4" dia, (type 400) laying on cement concrete 6" thick over 4ft -0" up to 6ft -0" depth of invert including excavation and cement concrete hunching (1:3:6(1")).
Drains, P.V.C, 4" dia: (type 600) laying on cement concrete 6" thick up to 2ft 0" depth of invert including excavation, back filling and cement concrete hunching 1:3:6(1").
Drains P.V.C, 4" dia. (type 600) laying on cement concrete 6" thick over 2 ft. up to 4 ft. depth of invert including excavation back filling and cement concrete hunching 1:3:6(1").
Drains P.V.C, 4" dia. (type 600) laying on cement concrete 6" thick over 4 ft. up to 6 ft. depth of invert including excavation back filling and cement concrete hunching 1:3:6(1").
Drains PVC, 6" dia. (type 600) laying on cement concrete 6" thick up to 2ft. depth of invert including excavation , backfilling and cement concrete hunching 1:3:6 (1").
Drains PVC, 6" dia.( type 600 ) laying on cement concrete 6" thick over 2ft. up to 4ft. depth of invert including excavation backfilling and cement concrete hunching 1:3:6 (1" ).
Drains PVC, 6" dia.( type 600 ) laying on cement concrete 6" thick 4ft. up to 6ft. depth of invert including excavation backfilling and cement concrete hunching 1:3:6 (1") .
BSR 2014- Department of Buildings
S07- 275
Description Item Unit
L.ft
Drains PVC, 12" dia.( type 600 ) laying on cement concrete 6" thick over 2ft. up to 4ft. depth of invert including excavation backfilling and cement concrete hunching 1:3:6 (1" ).
BSR 2014- Department of Buildings
S07- 276
Description Item Unit
S-MISCELLANEOUS
L.ft
L.ftBamboo supplying only at site. L.ftBamboo supplying and fixing in position. L.ftBamboos removing and refixing with coir strings. L.ft Scaffolding of Bamboos
Nos
NosSteel scaffolding SetsHiring a steel scaffolding set per day at site. NosLabour for handling, Erecting & dismantling a steel scaffolding set . (up to 30' feet height )
NosGarden lamp
NosFencingNote: Refer Item numbers From J080 to JO82 for chain-link fencing
L.ft
L.ft
L.ft
L.ft
L.ftFence barbed wire fixing with G.I staples on existing timber posts (Barbed wire available).
L.ft
L.ft
Bamboo barricade 3ft 0" high composing of whole bamboos with one horizontal runner and uprights 6ft 0" apart, supplying and fixing and removing as and when required, (Salvaged materials to be contractor s property)
Bamboo barricade 4ft 0" high with 2 horizontal runners and uprights 6ft 0" apart, supplying and fixing and removing as and when required, (Salvaged materials to be contractor s property).
Erecting scaffolding of Bamboos and planks for lifting or lowering of storage tanks to a height of 15ft to 30ft and removing same after completion of work (salvaged materials to be contractor's property).
Erecting scaffolding of Bamboos and planks for lifting or lowering of storage tanks to a height of 30ft to 50ft and removing same after completion of work (salvaged materials to be contractor s property).
Supplying and fixing garden lamp (Mushroom type)
Fence, G.I barbed wire( gauge 14), four needles per each node & 4" apart with three curls of wire, supplying & fixing on existing timber posts with G.I staples. (Min Tensile Strength of B.wire 310 N/mm2)
Fence, G.I barbed wire( gauge 14), four needles per each node & 4" apart with three curls of wire, supplying & fixing on existing concrete posts with available hook bolts. (Min Tensile Strength of B.wire 310 N/mm2)
Fence, G.I barbed wire( gauge 14), four needles per each node & 4" apart with three curls of wire, supplying & fixing in renewing short lengths on timber posts. (Min Tensile Strength of B.wire 310 N/mm2)
Fence, G.I barbed wire( gauge 14), four needles per each node & 4" apart with three curls of wire, supplying & fixing on concrete posts with available hook bolts, (Min Tensile Strength of B.wire 310 N/mm2)
Fence, PVC coated barbed wire, four needles per each node & 3" apart with three curls of wire, supplying & fixing on concrete posts with available hook bolts.
Fixing barbed wire fence with G.I staples on concrete posts with available hook bolts.(barbed wire available).
BSR 2014- Department of Buildings
S07- 277
Description Item Unit
Fence, barbed wire, straining only and refixing with staples, (barbed wire available)L.ft
Fence, barbed wire, straining only and refixing on concrete posts with available hook bolts. L.ft
L.ft
Nos
Nos
Nos
L.ftNos
L.ftWell, bailing out water
L.ft
L.ftWell, bailing out water, 8ft -10ft dia. and 20ft -30ft depth. say 5ft 0" depth of water
L.ftDewatering from excavated foundation pits or Trenches using submersible pump.
DayWater proofing (Treatment)
sq.ft
sq.ftWater proofing (Membrane)
sq.ftTimber treatment
Fence posts or struts, Milla, Na, Palu or Satin 4" to 6" average dia. supplying and fixing in ground complete, inclusive of sharpening and tarring.
Intermediate fence posts or struts, cement concrete 1:1 1/2: 3 (3/4") reinforced with 4 Nos. 1/4" dia. M.S rods, 5ft 7" high square section 4" to 6" supplying and fixing complete as per drawing No. 68 of 22.07.1936.
Intermediate fence posts or structs, cement concrete 1:1 1/2: 3 (3/4") reinforced with 4 Nos. 1/4" dia. M.S rods, 7ft 6" high square section 4" to 6" supplying and fixing complete as per drawing No. 68 of 22.07.1936.
End post and strut for Type barbed wire fence supplying and fixing complete in cement concrete as per drawing No: 68 of 1936.
Fence, bared wire, 5 strands, 12 1/2 B.W.G with 4 points at 3" centers and R.C. posts (1:2:4) 3/4" metal, reinforced with 4 Nos. 1/4" rods with No. 14 B.W.G stirrups at 8" centers. Post to be fixed at 8ft 0" centers including excavation, cement concrete
Straining Bolts, 18" long 1/2" dia. making and fixing (approx.). Stoneware pipes, 4" dia, over fume cupboards, supplying and fixing along wall with iron brackets and plugs.
Well, bailing out water, 5ft -7" dia. up to 20ft depth including cleaning well. say 5ft 0" depth of water
Well, bailing out water, 5ft -7" dia. up to 21ft to 30ft depth including cleaning well. say 5ft 0" depth of water
Waterproofing treatment using "Xypex" or equivalent approved product including preparation of surface according to Manufacturer s Specifications.
Waterproofing treatment using "Thoroseal" or equivalent approved product including preparation of surface, according to Manufacturer s Specifications.
Supply & Laying 1000 gauge Polythene membrane.
BSR 2014- Department of Buildings
S07- 278
Description Item Unit
cu.ft
Structural Timber treated by Vacuum Pressure Impregnation Technique with approved wood preservatives such as CCB that are registered by register of pesticides, for protection against wood destroying agents such as wood bores, fungi and termites. (Execution according to the Manufacturers specifications) (By "Finlay Celurised treated " or equivalent system) Rate per Cubic Foot = Rs. 311.61/- inc Vat
BSR 2014- Department of Buildings
S07- 279
Description Item Unit
Door PVC
sq.ft
sq.ft
L.ftLandscaping
Laying turf sods
sq.ftLocal fruit treesSupply and planting Mango tree ( about 4' tall ) NosSupply and planting Guava tree ( about 4' tall ) NosSupply and planting Jambu tree ( about 4' tall ) NosSupply and planting Anoda tree ( about 4' tall ) NosSupply and planting Naminan tree ( about 4' tall ) NosSupply and planting Asoka tree ( about 4' tall ) NosSupply and planting Bamboo tree ( about 4' tall ) NosPalm trees
NosNosNosNosNosNos
Mixed FlowerNosNosNosNosNosNos
Road Construction
Cube
Cube
Cube
CubeSpreading ,watering & rolling 4" aggregate including hire charges of roller.
Cube
Door PVC supply and fixing to existing opening, (with out frame), Lock, complete with altered size with out preparing reveals. (Size 2' 6" x 6' 9")
Door PVC supply and fixing to existing opening, with frame, Lock, complete with altered size with out preparing reveals. (Size 2' 6" x 6' 9")
Supplying and fixing PVC step nosing to stairway step edges using approved adhesive.
Supplying & laying turf sods of approved type including bedding material, pegging and watering.
Supply and planting Fox tail tree. ( about 5' tall ) Supply and planting Ceiling Wax tree. ( about 5' tall ) Supply and planting Raffic tree. ( about 5' tall ) Supply and planting Kentia tree. ( about 5' tall ) Supply and planting Cane tree. ( about 5' tall ) Supply and planting Royal palm tree. ( about 5' tall )
Supply and planting Cannas plant. Supply and planting Idda plant. Supply and planting Exoria Medium plant. Supply and planting Royal Exoria plant. Supply and planting Hibiscus plant. Supply and planting Bougainville plant (about 2' tall)
Supplying and pilling approved 4" aggregate for road construction, at site excluding hire charges.
Supplying and pilling approved 1 1/2" aggregate for road construction, at site excluding hire charges.
Supplying and pilling approved 3/4" aggregate for road construction, at site excluding hire charges.
Supplying and pilling approved 1/2" aggregate for road construction, at site excluding hire charges.
BSR 2014- Department of Buildings
S07- 280
Description Item Unit
Spreading ,watering & rolling 2"- 3/4" aggregate including hire charges of roller.Cube
Sqr
Sqr
Sqr
SqrProviding Labour Services Providing Labour services in Un Skilled trades of any type of manual work on day work basis.
DayProviding Labour services in semi Skilled trades, on day work basis. Day
Day
DayFlaggingCords, woven, or picture, supplied and fixed. L.ftCords, flag, 1/4" dia. supplied and fixed. L.ftCords, flag mast, 3/8" dia. supplied and fixed. L.ftCords, flag mast, 1/2" dia. supplied and fixed. L.ft
Nos
Nos
NosFlagpoles (available) planted as directed removed when required, and ground made good.
Nos
Bitumen(80/100) surfacing first coat using 2Ltr/Sq.m including blinding with sand at the rate of 125 Sq.m/Cu.m.
Bitumen(80/100) surfacing 2 nd subsequent coat using 1 Ltr/Sq.m including blinding at the rate of 125 Sq.m/Cu.m
Emulsion /Cold bitumen (CRS-1) surface treatment 1st coat with 3.5 Ltr/Sq.m including blinding with sand,@125 Sq.m/Cu.m(Manual)
Emulsion /Cold bitumen (CRS-1) surface treatment subsequent coat using 0.075 Ltr/Sq.m including blinding with sand,@125 Sq.m/Cu.m(Manual)
Providing Labour services in Skilled trades such as Mason, Carpenter, Bar bender ,Painter, polisher, Plumber, Simple Machines operator etc. on day work basis.
Providing Labour services in Skilled trades such as Fitter, Electrician, Welder, Tiller, Glazier, Tinker, Mechanic, Aluminium fabricator, Heavy equipment operator, Sign board Painter etc. on day work basis.
Flags, average size 6ft x 3ft hung up on buildings as directed and removed when required. (Flags available - any poles used are to be paid for separately)
Flags, small (Burges) hung up on buildings as directed and removed when required. (Flags available - any poles used are to be paid for separately) (up to 100)
Flags, small (Burges) hung up on buildings as directed and removed when required. (Flags available - any poles used are to be paid for separately) (over 1000)
BSR 2014- Department of Buildings
S07- 281
Description Item Unit
T-ELECTRICAL INSTALLATIONS
Recommended makes of Electrical Accessories
Recommended Fabricators of Switch boards and Enclosures.
ElsteelK.I.K. Lanka (Pvt) LtdPubudu Engineering (pvt) LtdRichardsons Projects (pvt) LtdBentota Power Generators (Pvt) LtdOS Project (Pvt) Ltd. (Orange)Or similar product
MCCB:- Merlin Gerine, ABB, Terasaki, Siemens or equivalent.
MCB’S & RCCB’S:- Merlin Gerine , Siemens, Crabtree, Hager, Moeller, Legrand, F & G (Austria) or equivalent.
Cable :- ACL, Kelani or equivalent.
Ceiling Fan:- K.D.K., National-Japanese originsExhaust Fan:- K.D.K., National-Japanese origins
Switch & socket outlet :- Tenby, Clipsal, MK, Crabtree, PDL, Kevilton, Orange or Equivalent.
Fluorescent Lamp:- The choke, starter and capacitor should be of good Quality. British, French, Australia, German or equivalent And the tube should be preferably Thorn, Osram National Or equivalent. The fluorescent fittings should be fabricated In gauge not smaller than 24 SWG Zinc coated metal, Finished with power coating (white in colour).
Distribution Board:- Shall be in surface mount metal enclosure fabricated With Zinc coated sheet metal of gauge not less than 1.8 mm total enclosed, with hinged door with protective cover plate for terminals, finished with powder coating of approved colour and components as specified in the BOQ.
Energy Saving Bulbs:- 4 star rated.
BSR 2014- Department of Buildings
S07- 282
Description Item Unit
In PVC conduit
Lamp point wiring NosWater tight lamp point wiring NosIndoor Bracket lamp point wiring NosStair way lamp point wiring controlled by 2 No. two way switches NosCeiling fan point wiring complete with hook and sunk switch Nos5 AMP switch socket outlet NosIn PVC conduit
13 AMP switch socket outlet Nos15 AMP switch socket outlet Nos15 AMP switch socket outlet c/w 20A DP Switch with Neon Indicator Lamp
NosIn PVC Casing
Lamp point wiring NosWater tight lamp point wiring NosIndoor Bracket lamp point wiring NosStair way Lamp point wiring controlled by 2 No. two way switches. NosCeiling fan point wiring complete with fan hook and sunk switch. Nos5 AMP switch socket outlet NosIn PVC Casing
13 AMP switch socket outlet (Radial Circuit) Nos15 AMP switch socket outlet Nos15 AMP switch socket outlet c/w 20A DP NosDistribution Boards
2 way SP & N Distribution board complete with 30AMP 2P MCB and 40A 2P RCD(30mA)Nos
4 way SP & N Distribution board complete with 30AMP 2P MCB and 40A 2P RCD(30mA)Nos
6 way SP & N Distribution board complete with 30AMP 2P MCB and 40A 2P RCD(30mA)Nos
Point wiring to be carried out with 2x1mm2 PVC/PVC/CU + 2.5mm2 PVC/CU earth cable terminated in a 3 terminal ceilingrose and sunk switch, wired in concealed conduit in wall and above ceiling to be supplied and installed to working order
wiring to be carried out with 2C,2.5mm2 PVC/PVC/CU + 2.5mm2 PVC/CU earth cable wired in concealed conduit in wall and above ceiling to be supplied and installed to working order
point wiring to be carried out with 2x1mm2 PVC/PVC/CU + 2.5mm2 PVC/CU earth cable terminated in a 3 terminal ceiling rose and sunk switch, wired with PVC casing on wall and on soffit to be supplied and installed to working order.
Wiring to be carried out with 2C,2.5mm2 PVC/PVC/CU + 2.5mm2 PVC/CU earth cable wired in concealed conduit in wall and above ceiling to be supplied and installed to working order
Supply, Wiring and Installation of distribution board in surface mount plastic enclosure with the undermentioned switch gears to working order.
BSR 2014- Department of Buildings
S07- 283
Description Item Unit
8 way SP & N Distribution board complete with 30AMP 2P MCB and 40A 2P RCD(30mA)Nos
10 way SP & N Distribution board complete with 30AMP 2P MCB and 40A 2P RCD(30mA)Nos
12 way SP & N Distribution board complete with 30AMP 2P MCB and 40A 2P RCD(30mA)Nos
2 way SP & N Distribution board complete with 60AMP 2P MCB and 60A 2P RCD(30mA)Nos
4 way SP & N Distribution board complete with 60AMP 2P MCB and 60A 2P RCD(30mA)Nos
6 way SP & N Distribution board complete with 60AMP 2P MCB and 60A 2P RCD(30mA)Nos
8 way SP & N Distribution board complete with 60AMP 2P MCB and 60A 2P RCD(30mA)Nos
10 way SP & N Distribution board complete with 60AMP 2P MCB and 60A 2P RCD(30mA)Nos
12 way SP & N Distribution board complete with 60AMP 2P MCB and 60A 2P RCD(30mA)Nos
Nos
Nos
Nos
NosSupplying and Installation of 20-100AMP 4P MCCB in surface mount metal enclosure
NosSupplying and Installation of 30AMP 2P isolator complete with plastic enclosure.
NosSupplying and Installation of 60AMP 2P isolator complete with plastic enclosure.
NosSupplying and Installation of 30AMP 4P isolator complete with plastic enclosure.
NosSupplying and Installation of 60AMP 4P isolator complete with plastic enclosure.
NosSupplying and Installation of 40AMP 2P RCCB (30mA) complete plastic enclosure.
NosSupplying and Installation of 60AMP 2P RCCB (30mA) complete plastic enclosure.
NosSupplying and Installation of 40AMP 4P RCCB (30mA) complete plastic enclosure.
Nos
Supplying and Installation of 2 way TP & N Distribution board complete with 60 A 4P MCB and 2 No. 32 A 3P MCB (10kA) in surface mount plastic enclosure.
Supplying and Installation of 4 way TP & N Distribution board complete with 60 A 4P MCCB and 4 No. 16 A 3P MCB type 3 in surface mount metal enclosure.
Supplying and Installation of 2 way TP & N Distribution board complete with 100 A 4P MCCB and 2 No. 30/60AMP 3P MCCB in surface mount metal enclosure.
Supplying and Installation of 4 way TP & N Distribution board complete with 125 A 4P MCCB and 4 No. 30/60AMP 3P MCCB in surface mount metal enclosure.
BSR 2014- Department of Buildings
S07- 284
Description Item Unit
Supplying and Installation of 60AMP 4P RCCB (30mA) complete plastic enclosure.Nos
BSR 2014- Department of Buildings
S07- 285
Description Item Unit
Cabling in conduits
2x1 sq. mm + 2.5 sq. mm E cable M2x2.5 sq. mm + 2.5 sq. mm E cable M2x4 sq. mm + 2.5 sq. mm E cable M2x6 sq. mm + 6 sq. mm E cable M2x10 sq. mm + 10 sq. mm E cable M2x16 sq. mm + 16 sq. mm E cable M2x25 sq. mm + 16 sq. mm E cable M4x2.5 sq. mm + 2.5 sq. mm E cable M4x4 sq. mm + 4 sq. mm E cable M4x6 sq. mm + 6 sq. mm E cable M4x10 sq. mm +10 sq. mm E cable M4x16 sq. mm +16 sq. mm E cable M4x25 sq. mm +16 sq. mm E cable M4x35 sq. mm +16 sq. mm E cable MUnarmoured Cabling
2C Cu/PVC/PVC 1.5 sq. mm + 2.5 sq. mm E cable M2C Cu/PVC/PVC 2.5 sq. mm + 2.5 sq. mm E cable M2C Cu/PVC/PVC 4 sq. mm + 2.5 sq. mm E cable M2C Cu/PVC/PVC 6 sq. mm + 6 sq. mm E cable M2C Cu/PVC/PVC 10 sq. mm + 10 sq. mm E cable M2C Cu/PVC/PVC 35 sq. mm + 16 sq. mm E cable M1C Cu/XLPE/PVC 35 sq. mm + 16 sq. mm E cable M1C Cu/XLPE/PVC 50 sq. mm + 25 sq. mm E cable M1C Cu/XLPE/PVC 70 sq. mm + 35 sq. mm E cable MArmoured Cabling
4C Cu/XLPE/SWA/PVC 25 sq. mm M4C Cu/XLPE/SWA/PVC 35 sq. mm M4C Cu/XLPE/SWA/PVC 50 sq. mm M4C Cu/XLPE/SWA/PVC 70 sq. mm M4C Cu/XLPE/SWA/PVC 95 sq. mm M4C Cu/XLPE/SWA/PVC 120 sq. mm M4C Cu/XLPE/SWA/PVC 150 sq. mm MCabling in PVC Casing2x1 sq. mm + 2.5 sq. mm E cable M2x2.5 sq. mm + 2.5 sq. mm E cable M2x4 sq. mm + 2.5 sq. mm E cable M2x6 sq. mm + 6 sq. mm E cable M2x10 sq. mm +10 sq. mm E cable M
Cable shall be PVC/PVC/CU unless other wise specified to be supplied and installed in conduit to working order.
Cable shall be Cu/PVC/PVC OR Cu/XLPE/Cu supplied and installed in conduit or pressure pipe (type 1000) to working order.
Cable shall be Cu/XLPE/SWA/PVC (BS 5467 : 1997 600/1000V) supplied and installed in cable tile with necessary accessories & materials to working order.
BSR 2014- Department of Buildings
S07- 286
Description Item Unit
2x16 sq. mm +16 sq. mm E cable M2x25 sq. mm +16 sq. mm E cable M4x2.5 sq. mm + 2.5 sq. mm E cable M4x4 sq. mm + 4 sq. mm E cable M4x6 sq. mm + 6 sq. mm E cable M4x10 sq. mm + 10 sq. mm E cable M4x16 sq. mm + 16 sq. mm E cable M4x25 sq. mm + 16 sq. mm E cable M4x35 sq. mm + 16 sq. mm E cable MEarth Electrode
NosLuminaries and Fixtures
Pendent Lamp C/W 250 mm dia. Conical plastic shade and 15W CFL bulb Nos
Pendent Lamp C/W 200 mm dia. Glass globe and 15W CFL bulb NosIndoor Bracket lamp C/W 200mm dia. Opal white glass globe & 11W CFL bulb
NosWater tight bracket lamp C/W 200mm dia. Clear aerylic globe & 15W CFL bulb(4 star rated)
Nos
Nos
Nos
Nos
NosFluorescent lamp fitting 1200mm single batten type with 1X36W bulb NosFluorescent lamp fitting 1200mm single totally encased suspension type with 1X36W bulb
NosFluorescent lamp fitting 600mm single totally encased suspension type with 1X18W bulb
Nos
Nos
Nos
NosFluorescent lamp fitting 1200mm single industrial type c/w 1X36W bulb (suspension type)
NosFluorescent lamp fitting 1200mm twin industrial type c/w 2X36W bulb (suspension type)
Nos
Supplying and Installation of earth Electrode 50 mm dia. Of 2 LM to working order complete with forming of a gulley around the pipe.
Supplying and Installation of Luminaries and fixtures complete with all fixing accessories, G.I. Chains cup hook 2/3 core cable, connector suspension holder etc. to working order.
Recessed fluorescent lamp fitting 1200mmx600mm complete with polished Aluminium double parabolic louver and 2X36W bulb
Recessed fluorescent lamp fitting 1200mmx600mm complete with polished Aluminium double parabolic louver and 3X36W bulb
Recessed fluorescent lamp fitting 600mmx600mm complete with polished Aluminium double parabolic louver and 4X18W bulb
Recessed fluorescent lamp fitting 600mmx600mm complete with polished Aluminium double parabolic louver and 3X18W bulb
Fluorescent lamp fitting 1200mm single complete with prismatic diffuser and 1X36W bulb suspension type
Fluorescent lamp fitting 600mm single complete with prismatic diffuser and 1X18W bulb suspension type
Fluorescent lamp fitting 1200mm twin complete with prismatic diffuser and 2X36W bulb suspension type
BSR 2014- Department of Buildings
S07- 287
Description Item Unit
Fluorescent lamp fitting 600mm single industrial type c/w 1X18W bulb (suspension type)Nos
NosCeiling lamp fitting C/W 250mm dia. Half spherical glass globe and 18W CFL bulb
NosBulk head lamp water tight C/W 18W CFL bulb (4 star rated) NosSwitch socket outlet
5 AMP switch socket outlet Nos13 AMP switch socket outlet Nos15 AMP switch socket outlet NosReplacing sunk switch
Replacing 1 gang sunk switch NosReplacing 2 gang sunk switch NosReplacing 3 gang sunk switch NosReplacing 4 gang sunk switch NosReplacing 5 gang sunk switch NosReplacing fan regulator dimmer type NosReplacing Ceiling fan regulator NosReplacing 20 AMP DP switch with Neon indicator NosReplacing sunk Bell push NosReplacing Cell Bell Ding Dong type excluding wires NosFans
NosExhaust Fans
Nos
Nos
Nos
NosWall Fans
NosFluorescent LampSupply & Installation of fluorescent lamp components to working order20W/40W Choker Nos20W/40W starter Nos
Recessed Down light fitting complete with 200mm dia. Polished Aluminium reflector and 20W CFL bulb
Switch socket outlet 5AMP/13Amp/15AMP to be supplied and installed complete with screws etc. to working order. ( Excluding wires & conduits )
Replacing sunk switch complete with plastic sunk box to be supplied and installed to working order.
Supply & Installation of Ceiling fan 1400mm dia. Complete with 3 speed regulator (Excluding wiring)
Supply & Installation of 200mm dia. Exhaust fan with auto shutter (K.D.K or equivalent) (Excluding wiring)
Supply & Installation of 250mm dia. Exhaust fan with auto shutter (K.D.K or equivalent) (Excluding wiring)
Supply & Installation of 300mm dia. Exhaust fan with auto shutter (K.D.K or equivalent) (Excluding wiring)
Supply & Installation of 450mm dia. Exhaust fan with auto shutter (K.D.K or equivalent) (Excluding wiring)
Supply & Installation of wall fan 450mm dia. Complete with 3 speed regulator (Excluding wiring)
BSR 2014- Department of Buildings
S07- 288
Description Item Unit
Capacitor 2.5-3.5MF NosFluorescent bulb 36W NosConduit PipeSupplying & installation of conduit pipe clipped in surface18mm conduit pipe M20mm conduit pipe M25mm conduit pipe M30mm conduit pipe M40mm conduit pipe M50mm conduit pipe MPVC CasingSupplying and Installation of PVC casing10mmx20mm PVC Casing M14mmx24mm PVC Casing M16mmx40mm PVC Casing M25mmx40mm PVC Casing M50mmx25mm PVC Casing M50mmX50mm PVC Box Casing M50mmX75mm PVC Box Casing M100mmX50mm PVC Box Casing M100mmx27mm PVC Box Casing MCommissioning Wires 2x1 sq. mm Cu/PVC/PVC Cable M2 x 2.5 sq. mm Cu/PVC/PVC Cable M2 x 4 sq. mm Cu/PVC/PVC Cable M2 x 6 sq. mm Cu/PVC/PVC Cable M2 x 10 sq. mm Cu/PVC/PVC Cable M2 x 16 sq. mm Cu/PVC/PVC Cable M2 x 25 sq. mm Cu/PVC/PVC Cable M2 x 35 sq. mm Cu/PVC/PVC Cable MCommissioning Earth Wires 2.5 sq. mm Cu/PVC Earth cable M6 sq. mm Cu/PVC Earth cable M10 sq. mm Cu/PVC Earth cable M16 sq. mm Cu/PVC Earth cable MSUPPLY & INSTALLATION OF DOL STARTERSingle phase DOL starter for 5.5kW motor (without overload) NosThree phase DOL starter for 5.5kW motor (without overload) Nos
BSR 2014- Department of Buildings
S07- 289
Description Item Unit
U-ALUMINIUM FABRICATORBoards and Glass PansOne Side Fabric Pasted 3mm thick Ply Wood Boards for Partitions
sq.ft
sq.ftPVC Laminated Ply Board for Partitions, Doors or Windows
sq.ftOne Side Coloured Al. Composite Cladding Boards for Partitions only
sq.ftOne Side Coloured Al. Composite Cladding Boards for Doors and Windows
sq.ftBoth Sides Coloured Al. Composite Cladding Boards for Partitions only
sq.ftBoth Sides Coloured Al. Composite Cladding Boards for Doors and Windows
sq.ftClear Glass 5mm thick for Partitions only
sq.ft
Supplying & Fabricating of Panel Boards consist of fabric cloths (Alabama or equivalent.) and sponge sheets pasted on one side of the ply wood board (3mm thick) and fix to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.
Both Sides Fabric Pasted 3mm thick Ply Wood Boards for Partitions, Doors or Windows
Supplying & Fabricating of Panel Boards consist of fabric cloths (Alabama or equivalent.) and sponge sheets pasted on BOTH sides of the ply wood board (3mm thick) and fix to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.
Supplying, Fabricating and Fixing 3mm thick PVC Laminated Ply Boards to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.)
Supplying, Fabricating & Fixing of 4mm thick Al. Composite Cladding Boards (One side Coloured) to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.)
Supplying, Fabricating & Fixing of 4mm thick Al. Composite Cladding Boards (One side Coloured) to existing door or window frame work with necessary rubber beadings.
Supplying, Fabricating & Fixing of 4mm thick Al. Composite Cladding Boards in SINGLE SIDE of the existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.)
Supplying, Fabricating & Fixing of 4mm thick Al. Composite Cladding Boards in SINGLE SIDE of the existing door or window frame work with necessary rubber beadings.
Supplying and Fixing of 5mm thick clear glass pan to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.)
BSR 2014- Department of Buildings
S07- 290
Description Item Unit
Clear Glass 5mm thick for Doors and Windows
sq.ftSupplying and Fixing of 5mm thick clear glass pan to existing door or window frame work with necessary rubber beadings.
BSR 2014- Department of Buildings
S07- 291
Description Item Unit
Float Glass 5mm thick for Partitions only
sq.ftFloat Glass 5mm thick for Doors and Windows
sq.ftTinted Glass 5mm thick for Partitions only
sq.ftTinted Glass 5mm thick for Doors and Windows
sq.ftClear Glass 6mm thick for Partitions only
sq.ftClear Glass 6mm thick for Doors and Windows
sq.ftSand Blast StickersSupplying cutting and pasting of sand blast stickers in position. sq.ft
Note: Refer figures for more details
Typical Aluminium Louvers
Matt Finished Louver blades sq.ftNatural Anodized Louver blades sq.ftBronze Anodized Louver blades sq.ftPowder Coated Louver blades sq.ftWood Finished Louver blades sq.ft
Matt Finished Louver blades sq.ftNatural Anodized Louver blades sq.ftBronze Anodized Louver blades sq.ftPowder Coated Louver blades sq.ft
Supplying and Fixing of 5mm thick float glass pan to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.)
Supplying and Fixing of 5mm thick float glass pan to existing door or window frame work with necessary rubber beadings.
Supplying and Fixing of 5mm thick tinted glass pan to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.)
Supplying and Fixing of 5mm thick tinted glass pan to existing door or window frame work with necessary rubber beadings.
Supplying and Fixing of 6mm thick clear glass pan to existing partition frame work. (Rate Exclusive of Aluminium beadings, necessary rubber beadings, fasteners & etc.)
Supplying and Fixing of 6mm thick clear glass pan to existing door or window frame work with necessary rubber beadings.
Aluminium Louvers with Louver Frame (52.5mm high 34.6mm wide Louver blades; Alumex DG 01 or equivalent)
Supplying, Fabricating and Fixing 1.2mm thick 52.5mm high 34.6mm wide Louver blades (Alumex DG 01 or equivalent) to 20.0 X 37.0mm louver frame (Alumex DG 101 or equivalent) and fix to existing door, window or partition frame work including necessary accessories.
Aluminium Louvers with Louver Frame (60.0mm high 28.5mm wide Louver blades; Alumex DG 03 or equivalent)
Supplying, Fabricating and Fixing 1.2mm thick 60.0mm high 28.5mm wide Louver blades (Alumex DG 03 or equivalent) to 17.0 X 31.0mm louver frame (Alumex DG 103 or equivalent) and fix to existing door, window or partition frame work including all accessories.
BSR 2014- Department of Buildings
S07- 292
Description Item Unit
Wood Finished Louver blades sq.ft
BSR 2014- Department of Buildings
S07- 293
Description Item Unit
Matt Finished Louver blades sq.ftNatural Anodized Louver blades sq.ftBronze Anodized Louver blades sq.ftPowder Coated Louver blades sq.ftWood Finished Louver blades sq.ft
Matt Finished Louver blades sq.ftNatural Anodized Louver blades sq.ftBronze Anodized Louver blades sq.ftPowder Coated Louver blades sq.ftWood Finished Louver blades sq.ft
Matt Finished Louver blades sq.ftNatural Anodized Louver blades sq.ftBronze Anodized Louver blades sq.ftPowder Coated Louver blades sq.ftWood Finished Louver blades sq.ftAluminium SUN Louvers with Louver Frame (Alumex ALU 180 or equivalent)
Matt Finished Louver blades sq.ftNatural Anodized Louver blades sq.ftBronze Anodized Louver blades sq.ftPowder Coated Louver blades sq.ft
Aluminium Louvers with Louver Frame (34.5mm high 28.5mm wide symmetrical "Y" type Louver blades; Alumex DG 04 or equivalent)Supplying, Fabricating and Fixing 1.2mm thick 34.5mm high 28.5mm wide symmetrical "Y" type Louver blades (Alumex DG 04 or equivalent) to 17.0 X 31.0mm louver frame (Alumex DG 103 or equivalent) and fix to existing door, window or partition frame work including all accessories.
Aluminium Louvers (39.5mm high 37.4mm wide asymmetrical "Y" type Louver blades; Alumex DG 06 or equivalent) with Louver Frame
Supplying, Fabricating and Fixing 1.2mm thick 39.5mm high 37.4mm wide asymmetrical "Y" type Louver blades (Alumex DG 06 or equivalent) to 17.0 X 40.0mm louver frame (Alumex DG 104 or equivalent) and fix to existing door, window or partition frame work including all accessories.
Aluminium Louvers (120.0mm high 37.4mm wide Louver blades; Alumex DG 05 or equivalent) with Louver Frame
Supplying, Fabricating and Fixing 1.5mm thick 120.0mm high 37.4mm wide Louver blades (Alumex DG 05 or equivalent) to 17.0 X 40.0mm louver frame (Alumex DG 104 or equivalent) and fix to existing door, window or partition frame work including all accessories
Supplying, Fabricating and Fixing 1.5mm thick 107.3mm high 26.0mm wide sun Louver blades (Alumex ALU-180 or equivalent) to 25.0 X 125.0mm louver frame (Alumex ALU-181 or equivalent) and fix to existing frame or wall. (Fix to existing frame or wall with accessories paid separately)
BSR 2014- Department of Buildings
S07- 294
Description Item Unit
Wood Finished Louver blades sq.ft
BSR 2014- Department of Buildings
S07- 295
Description Item Unit
Matt Finished Louver blades sq.ftNatural Anodized Louver blades sq.ftBronze Anodized Louver blades sq.ftPowder Coated Louver blades sq.ftWood Finished Louver blades sq.ftSingle Row Aluminium Partition Frame Work with Boards/Glass
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
Aluminium SUN Louvers (Alumex ALU 180 or equivalent) with BIRD'S MOUTH BRACKETS (Alumex ALU 282 or equivalent)
Supplying, Fabricating and Fixing 1.5mm thick 107.3mm high 26.0mm wide sun Louver blades (Alumex ALU-180 or equivalent) to Bird's mouth brackets (Alumex ALU-282 or equivalent) and fix to existing frame, Door, Window or wall with all accessories.
Single row Aluminium Partition Frame Work(1.2mm thick ) with Fully Board Panels (max. Height 1200mm)
Supplying, Fabricating and Installing of single row frame work with FULLY BOARDED panels in both sides for ALUMINIUM PARTITION consist of 1.2mm thick,76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions. And GI channel stiffener frame work enclosed in Aluminium frame work with an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (PANNLE BOARDS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
Single row Aluminium Partition Frame Work(1.2mm thick ) Fully Glass Pans (max. Height 1200mm)
Supplying, Fabricating and Installing single row panel frame work with Fully Glass ALUMINIUM PARTITION consist of 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions to form an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suited to the available space consist of glass pans. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (GLASS PANS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
BSR 2014- Department of Buildings
S07- 296
Description Item Unit
Single Row Aluminium Partition Frame Work with Louvers
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft2 Row Aluminium Partition Frame Work with Boards/Glass
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
Single Row Aluminium Partition Frame Work (1.2mm thick) Fully Louvered (max. Height 1200mm)
Supplying, Fabricating and Installing single row panel FULLY ALUMINIUM LOUVER PARTITION with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions to form an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and consist of Aluminium louver framed panel. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH CAGE PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
Two Row Compiled Aluminium Partition Frame Work (1.2mm thick) Fully Board Panels (max. height 2400mm)
Supplying, Fabricating and Installing two rows of panel frame work with FULLY BOARDED panels in both sides for(Top & Bottom rows) ALUMINIUM PARTITION consist of 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions. And GI channel stiffener frame work enclosed in Aluminium frame work with an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (PANEL BOARDS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
BSR 2014- Department of Buildings
S07- 297
Description Item Unit
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
Two Row Compiled Aluminium Partition Frame Work (1.2mm thick) - One Row with Boards & other Row with Glass Pans (max. height 2400mm)
Supplying, Fabricating and Installing GLASS & BOARD two rows of panel ALUMINIUM PARTITION frame work with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions. And one row consist of BOAD panels in both sides of the partition frame work and GI channel stiffener frame work enclosed in appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and additional GI channel bracings to be placed in 600mm centers at vertical direction and other row consist of glass pans, span not exceeding 1200mm in both directions. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (GLASS PANS & PANEL BOARDS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
Two Row compiled Aluminium Partition Frame Work (1.2mm thick) - with Fully Glass Pans
Supplying, Fabricating and Installing two rows of panel frame work with Fully Glass pans for (Top & Bottom rows) ALUMINIUM PARTITION consist of 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions to form an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suited to the available space. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (GLASS PANS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
BSR 2014- Department of Buildings
S07- 298
Description Item Unit
2 Row Aluminium Partition Frame Work with Louvers & Boards/Glass
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
Two Row compiled Aluminium Partition Frame Work (1.2mm thick)-One Row with Louvers and other Row with Boards (max. height 2400mm)
Supplying, Fabricating and Installing of LOUVER & BOARD two rows of panels ALUMINIUM PARTITION frame work with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions, One row consist of BOARD panels in both sides of the partition frame work and GI channel stiffener frame work enclosed in Aluminium frame, with appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Other row consists of LOUVER framed panels. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH CAGE & PANEL BOARDS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
Two Row compiled Aluminium Partition Frame Work (1.2mm thick)-One Row with Louvers and other Row with Glass (max. height 2400mm)
Supplying, Fabricating and Fixing LOUVER & GLASS two rows of panels ALUMINIUM PARTITION frame work with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions to form an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and one row consist of glass pans. Other row consists of LOUVER framed panels. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH CAGE & GLASS PANS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
BSR 2014- Department of Buildings
S07- 299
Description Item Unit
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft3 Row Aluminium Partitions
1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft2.0mm thick,100mm depth (width 50.0mm) (Alumex or eq.) Aluminium extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
Two Row compiled Aluminium Partition Frame Work (1.2mm thick) - Fully Louvered (max. height 2400mm)
Supplying, Fabricating and Fixing 2 rows of panel FULLY Aluminium LOUVER Partition with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions to form an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and both rows consist of Aluminium louver framed panels. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH CAGE PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
3 Row Compiled Aluminium Partition Frame Work (max. height 3600mm) - with Fully Board
Supplying, Fabricating and Installing 3 Row Compiled panel frame work with FULLY BOARDED panels in both sides for (Top middle & Bottom rows); ALUMINIUM PARTITION consist of 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions and GI channel stiffener frame work enclosed in Aluminium frame work with an appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (PANEL BOARDS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
BSR 2014- Department of Buildings
S07- 300
Description Item Unit
1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft2.0mm thick,100mm depth (width 50.0mm) (Alumex or eq.) extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ft
3 Row Compiled Aluminium Partition Frame Work - 2 Rows with Boards & Other Row with Glass Pans (max. height 3600mm)
Supplying, Fabricating and Installing GLASS & BOARD 3 row Compiled panel ALUMINIUM PARTITION frame work with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions. And two rows consist of BOAD panels in both sides of the partition frame work and GI channel stiffener frame work enclosed in appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Other row consists of glass pans, span not exceeding 1200mm in both directions. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (GLASS PANS & PANEL BOARDS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
3 Row Compiled Aluminium Partition Frame Work - 1 Row with Boards & Other 2 Rows with Glass Pans (max. height 3600mm)
Supplying, Fabricating and Installing GLASS & BOARD 3 row Compiled panel ALUMINIUM PARTITION frame work with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions. And one row consists of BOAD panels in both sides of the partition frame work and GI channel stiffener frame work enclosed in appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Other two rows consist of glass pans, span not exceeding 1200mm in both directions. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (GLASS PANS & PANEL BOARDS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
BSR 2014- Department of Buildings
S07- 301
Description Item Unit
Bronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ft
BSR 2014- Department of Buildings
S07- 302
Description Item Unit
Wood Finished Aluminium extrusion frame work sq.ft2.0mm thick, 100mm depth (width 50.0mm) (Alumex or eq.) extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft2.0mm thick, 100mm depth (width 50.0mm) (Alumex or eq.) extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
3 Row Compiled Aluminium Partition Frame Work - (max. height 3600mm) fully Glass Panels
Supplying, Fabricating and Installing 3 Row Compiled panel frame work with FULLY GLAZE pans for (Top middle & Bottom rows) ALUMINIUM PARTITION consist of 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions and glass pans, to form an appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions suited to the available space. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (GLASS PANS PAID SEPERATLY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
BSR 2014- Department of Buildings
S07- 303
Description Item Unit
3 Panel Aluminium Louver Partitions
1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft2.0mm thick, 100mm depth (width 50.0mm) (Alumex or eq.) Aluminium extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
3 Row Compiled Aluminium Partition Frame Work - (max. height 3600mm) one row with Louvers, Another row With Boards & Remaining row with Glass.
Supplying, Fabricating and Fixing 3 Row Compiled panel frame work with GLASS, BOARD & ALUMINIUM LOUVER PARTITION consist of 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions. And one row consists of BOAD panels in both sides of the partition frame work and GI channel stiffener frame work enclosed in appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Another row consists of necessary LOUVER framed panels & remaining row consists of glass pans suited to the available space. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH CAGE, GLASS PANS & PANEL BOARDS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
3 Row Compiled Aluminium Partition Frame Work - (max. height 3600mm) one row with Louvers, Remaining two rows with Boards.
BSR 2014- Department of Buildings
S07- 304
Description Item Unit
Supplying, Fabricating and Fixing 3 Row Compiled panel frame work with BOARD & ALUMINIUM LOUVER PARTITION consist of 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions. And two rows consist of BOAD panels in both sides of the partition frame work and GI channel stiffener frame work enclosed in appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and additional GI channel bracings placed in 600mm centers at vertical direction. Other remaining row consists of necessary LOUVER framed panels. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH CAGE & PANEL BOARDS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
BSR 2014- Department of Buildings
S07- 305
Description Item Unit
1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft2.0mm thick, 100mm depth (width 50.0mm) (Alumex or eq.) Aluminium extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft2.0mm thick, 100mm depth (width 50.0mm) (Alumex or eq.) Aluminium extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
3 Row Compiled Aluminium Partition Frame Work - (max. height 3600mm) one row with Louvers, Remaining two rows with Glass.
Supplying, Fabricating and Fixing LOUVER & GLASS 3 Row Compiled panel Aluminium Partition frame work with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions to form an appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suited to the available space. Two rows consist of glass pans. Other row consists of LOUVER panel frame with appropriate grid pattern suited to glass panels. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH CAGE & GLASS PANS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
BSR 2014- Department of Buildings
S07- 306
Description Item Unit
1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft2.0mm thick, 100mm depth (width 50.0mm) (Alumex or eq.) Aluminium extrusions
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
Aluminium 76mm Shopfront
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ftAluminium 100mm Shopfront
3 Row Compiled Aluminium Partition Frame Work - (max. height 3600mm) Fully Louvered.
Supplying, Fabricating and Fixing 3 Row Compiled panel FULLY ALUMINIUM LOUVERED PARTITION with 1.2mm thick, 76mm deep (width 23.0mm) (Alumex or eq.) Aluminium extrusions to form an appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suited to the available space and all rows consist of Louvers enclosed with Aluminium louver frame. Rate inclusive of Aluminium beadings (including necessary rubber beadings) necessary fasteners etc. (SUPPLY & FIXING OF LOUVER BLADES WITH LOUVER FRAME PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
Supplying, Fabricating and Installing 1.2 mm thick,76mmAluminium Shopfront, frame work fixed as an appropriate grid pattern not exceeding 1200mm in both vertical & horizontal directions, suit to the available space including necessary rubber beadings, fasteners etc. (SUPPLY & FIXING OF LOUVERS, GLASS PANS OR PANNLE BOARDS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
BSR 2014- Department of Buildings
S07- 307
Description Item Unit
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ftAluminium Curtain Wall (2.0mm thick)
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ftAluminium Curtain Wall (1.5mm thick)
Matt Finished Aluminium extrusion frame work sq.ftNatural Anodized Aluminium extrusion frame work sq.ftBronze Anodized Aluminium extrusion frame work sq.ftPowder Coated Aluminium extrusion frame work sq.ftWood Finished Aluminium extrusion frame work sq.ft
Aluminium doors
Supplying, Fabricating and Fixing 1.5 mm thick,100mmAluminium Shopfront, frame work fixed as an appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suit to the available space including necessary rubber beadings, fasteners etc. (SUPPLY & FIXING OF LOUVERS, GLASS PANS OR PANNLE BOARDS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
Supplying, Fabricating and Fixing Aluminium Curtain Wall with 2.0mm thick,98mm depth extrusions, frame work fixed as an appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suit to the available space including necessary rubber beadings, fasteners etc. (SUPPLY & FIXING OF LOUVERS, GLASS PANS OR PANNLE BOARDS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
Supplying, Fabricating and Fixing Aluminium Curtain Wall with 1.5mm thick,85mm depth extrusions, frame work fixed as an appropriate grid pattern, span not exceeding 1200mm in both vertical & horizontal directions, suit to the available space including necessary rubber beadings, fasteners etc. (SUPPLY & FIXING OF LOUVERS, GLASS PANS OR PANNLE BOARDS PAID SEPERATELY) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
Aluminium Double Sashed Swing Door (sash only) for 1.6mm thick 100mm Deep Door Frames
BSR 2014- Department of Buildings
S07- 308
Description Item Unit
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
Supplying, Fabricating and Installing of Aluminium Double sashed Swing Door (sash only) for 1.6mm thick 100mm deep door frames with suitable wool felt. Rate inclusive of necessary fasteners and hinges (Union or equivalent 102x76x2 mm) etc.( Glass/ Board, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. 100D-102, 100D-103, 100D-201, 100D-301, 100D-401, 100D-501 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U207-U241 for outer frame-
BSR 2014- Department of Buildings
S07- 309
Description Item Unit
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
Door Outer frames
-DO- Matt Finished Aluminium L.ft -DO- Natural Anodized Aluminium L.ft -DO- Bronzed Anodized Aluminium L.ft -DO-Powder Coated Aluminium L.ft -DO-Wood Finished Aluminium L.ft
-DO- Matt Finished Aluminium L.ft -DO- Natural Anodized Aluminium L.ft -DO- Bronzed Anodized Aluminium L.ft -DO-Powder Coated Aluminium L.ft -DO-Wood Finished Aluminium L.ft
Aluminium Single Sashed Swing Door (sash only) for 1.6mm thick 100mm Deep Door Frames
Supplying, Fabricating and Installing of Aluminium Single sashed Swing door (sash only) for 1.6mm 100mm deep door frames with suitable wool felt. Rate inclusive of necessary fasteners and hinges (Union or equivalent 102x76x2 mm) etc.( Glass/ Board/ Louver Panels, Door closers, door locks and door handles paid separately) door sash only.(Alumex extrusion No's 100D-101, 100D-103, 100D-201, 100D-301, 100D-401, 100D-501 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U207-U241 for outer frame-
Outer Door Frame (Frame Only) with1.6mm thick 100mm deep Extrusion for Aluminium Double Sashed Swing Door
Supplying, Fabricating and Installing 1.6mm thick 45mm X 100mm (depth) Aluminium outer door frame for double sash Swing door. Rate inclusive of necessary fasteners and etc.( Door sashes, Door closers, door locks and door handles paid separately) (Alumex extrusion No. 100D-3004H or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U197-U206 for door sash-
Outer Door Frame (Frame Only) with1.5mm thick 100mm deep Extrusion for Aluminium Single Sashed Swing Door
Supplying, Fabricating and Installing 1.5mm thick 45mmX100mm (depth) Aluminium Single sashed Swing door outer frame only. Rate inclusive of necessary fasteners and etc.( Door sashes, Door closers, door locks and door handles paid separately) (Alumex extrusion No. 100D-3005 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U197-U206 for door sash-
BSR 2014- Department of Buildings
S07- 310
Description Item Unit
-DO- Matt Finished Aluminium L.ft -DO- Natural Anodized Aluminium L.ft -DO- Bronzed Anodized Aluminium L.ft -DO-Powder Coated Aluminium L.ft -DO-Wood Finished Aluminium L.ft
-DO- Matt Finished Aluminium L.ft -DO- Natural Anodized Aluminium L.ft -DO- Bronzed Anodized Aluminium L.ft -DO-Powder Coated Aluminium L.ft -DO-Wood Finished Aluminium L.ft
-DO- Matt Finished Aluminium L.ft -DO- Natural Anodized Aluminium L.ft -DO- Bronzed Anodized Aluminium L.ft -DO-Powder Coated Aluminium L.ft -DO-Wood Finished Aluminium L.ft
Outer Door Frame (Frame Only) with 1.2mm thick 76mm deep Extrusion for Aluminium Single Sash Swing door
Supplying, Fabricating and Installing 1.2mm thick 45mmX76.2mm (depth) Aluminium Single sashed Swing door outer frame only. Rate inclusive of necessary fasteners and etc.( Door sashes, Door closers, door locks and door handles paid separately) (Alumex extrusion No. 76D-3102 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U197-U206 for door sash-
Outer Door Frame (Frame Only) with 1.5mm thick 100mm Deep SHOP FRONT Aluminium Extrusions
Supplying, Fabricating and Installing 1.5mm thick 100mm (depth) Aluminium Swing door outer frame for SHOP FRONT. Rate inclusive of necessary fasteners and etc.( Door sashes, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SPR-205, SPR-211or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U197-U206 for door sash-
Outer Door Frame (Frame Only) with 1.2mm thick 76mm Deep SHOP FRONT Aluminium Extrusions
Supplying, Fabricating and Installing 1.2mm thick 76mm (depth) Aluminium Swing door outer frame for SHOP FRONT. Rate inclusive of necessary fasteners and etc.( Door sashes, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SPR-105, SPR-211 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U197-U206 for door sash-
Outer Door Frame (Frame Only) with 1.2mm thick 76mm Deep Partition Frame Aluminium Extrusions
BSR 2014- Department of Buildings
S07- 311
Description Item Unit
-DO- Matt Finished Aluminium L.ft -DO- Natural Anodized Aluminium L.ft -DO- Bronzed Anodized Aluminium L.ft -DO-Powder Coated Aluminium L.ft -DO-Wood Finished Aluminium L.ft
-DO- Matt Finished Aluminium L.ft -DO- Natural Anodized Aluminium L.ft -DO- Bronzed Anodized Aluminium L.ft -DO-Powder Coated Aluminium L.ft -DO-Wood Finished Aluminium L.ft
Aluminium Sliding Doors
80mm (1.5 mm thick) Aluminium Sliding Door (Undivided plane Paneled Sashes)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
Supplying, Fabricating and Installing 1.2mm thick 76mm (depth) Aluminium Swing door outer frame with Aluminium Partition extrusions. Rate inclusive of necessary fasteners and etc.( Door sashes, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. PT-5159 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U197-U206 for door sash-
Outer Door Frame (Frame Only) with 1.2mm thick 76mm Deep Aluminium Extrusion for Single Sash Plywood door
Supplying, Fabricating and Installing 1.2mm thick 76mm (depth) Aluminium door outer frame for single sashed plywood door. Rate inclusive of necessary fasteners and etc.( Door sashes, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. 76D-3101 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, H069-H072 for plywood door-
Supplying, Fabricating and Installing 1.5mm thick 33.7mmX80mm (depth) Aluminium framed two sliding door sashes (Undivided plane Paneled Sashes) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. 80S-2001, 80S-2002, 80S2101 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
80mm (1.5 mm thick) Aluminium Sliding Door (Undivided plane Paneled Sashes) with top fixed panels
BSR 2014- Department of Buildings
S07- 312
Description Item Unit
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
Supplying, Fabricating and Installing 1.5mm thick 33.7mmX80mm (depth) Aluminium framed two sliding door sashes (Undivided plane Paneled Sash) with top fixed panels. Rate to include for suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. 80S-2001, 80S-2002, 80S2101 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
BSR 2014- Department of Buildings
S07- 313
Description Item Unit
100mm (1.5 mm thick) Aluminium Sliding Door (Undivided plane Paneled Sashes)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
100mm (1.5 mm thick) Aluminium Sliding Door (Sashes Divided to two Panels)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
Supplying, Fabricating and Installing 1.5mm thick 30mmX98mm (depth) Aluminium framed one half fixed & Single Sliding Door sash (Undivided plane Paneled Sashes) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001, DS-1101, SD1501 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
100mm (1.5 mm thick) Aluminium Sliding Door (Undivided plane Paneled Sashes) with top fixed panel
Supplying, Fabricating and Installing 1.5mm thick 30mmX98mm (depth) Aluminium framed one half fixed & Single Sliding Door sash (Undivided plane Paneled Sashes) with top fixed panels. Rate to include for suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001, DS-1101, SD1501 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
Supplying, Fabricating and Installing 1.5mm thick 30mmX98mm (depth) Aluminium framed one half fixed & Single Sliding Door sash (Sashes Divided to two Panels) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001, DS-1101, SD1501 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
BSR 2014- Department of Buildings
S07- 314
Description Item Unit
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
80mm (1.5 mm thick) Aluminium 3 track Sliding Door (Sashes Divided to two Panels)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
100mm (1.5 mm thick) Aluminium Sliding Door (Sashes Divided to two Panels) with top fixed panel
Supplying, Fabricating and Installing 1.5mm thick 30mmX98mm (depth) Aluminium framed one half fixed & Single Door sash (Sashes Divided to two Panels) with top fixed panels. Rate to include for suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001, DS-1101, SD1501 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
80mm (1.5 mm thick) Aluminium 3 track Sliding Door (Undivided plane Paneled Sashes)
Supplying, Fabricating and Installing 1.5mm thick 33.7mmX119.5mm (depth) Aluminium framed 80mm 3 track (one sash fixed & other two sliding) sliding Door sashes (Undivided plane Paneled Sashes) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. 80S-2001A, SS-2101, 80SFL-1001 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
Supplying, Fabricating and Installing 1.5mm thick 33.7mmX119.5mm (depth) Aluminium framed 80mm 3 track (one sash fixed & other two sliding) sliding Door sashes (Sashes Divided to two Panels) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. 80S-2001A, SS-2101, 80SFL-1001 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
BSR 2014- Department of Buildings
S07- 315
Description Item Unit
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
100mm (1.6 mm thick) Aluminium 3 track Sliding Door (Sashes Divided to two Panels)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
100mm (1.6 mm thick) Aluminium 3 track Sliding Door (Undivided plane Paneled Sashes)
Supplying, Fabricating and Installing 1.6mm thick 35mmX146.5mm (depth) Aluminium framed 100mm 3 track (one sash fixed & other two sliding) sliding Door sashes (Undivided plane Paneled Sashes) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001A, SD-1101A, SD-1302 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
100mm (1.6 mm thick) Aluminium 3 track Sliding Door (Undivided plane Paneled Sashes) with top fixed panel
Supplying, Fabricating and Installing 1.5mm thick 35mmX146.5mm (depth) Aluminium framed 100mm 3 track (one sash fixed & other two sliding) sliding Door sashes (Undivided plane Paneled Sashes) with top fixed panel. Rate to include for suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001A, SD-1101A, SD-1302 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
Supplying, Fabricating and Installing 1.6mm thick 35mmX146.5mm (depth) Aluminium framed 100mm 3 track (one sash fixed & other two sliding) sliding Door sashes (Sashes Divided to two Panels) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001A, SD-1101A, SD-1302 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
BSR 2014- Department of Buildings
S07- 316
Description Item Unit
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
100mm (1.6 mm thick) Aluminium 3 track Sliding Door (Sashes Divided to two Panels) with top fixed panel
Supplying, Fabricating and Installing 1.6mm thick 35mmX146.5mm (depth) Aluminium framed 100mm 3 track (one sash fixed & other two sliding) sliding Door sashes (Sashes Divided to two Panels) with top fixed panel. Rate to include for suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SD-1001A, SD-1101A, SD-1302 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
100mm (1.5 mm thick) Aluminium Double Glazed Sliding Door (Sashes Divided to two Panels)
Supplying, Fabricating and Installing 1.5mm thick 42.5mmX100mm (depth) Aluminium framed Double Glazed one half fixed & Single Sliding Door sash (Double Glazed Sashes Divided to two Panels) with suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SDG-2001, SDG-2101, SDG-2401 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
100mm (1.5 mm thick) Aluminium Double Glazed Sliding Door (Sashes Divided to two Panels) with top fixed panel
Supplying, Fabricating and Installing 1.5mm thick 42.5mmX100mm (depth) Aluminium framed Double Glazed one half fixed & Single Sliding Door sash (Double Glazed Sashes Divided to two Panels) with top fixed panels. Rate to include for suitable rubber beadings, necessary fasteners, rollers & etc.( Glass pans or panel boards, Door closers, door locks and door handles paid separately) (Alumex extrusion Nos. SDG-2001, SDG-2101, SDG-2401 and etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
BSR 2014- Department of Buildings
S07- 317
Description Item Unit
Aluminium Casement WindowsCasement Window Frames Only
41mm Aluminium Casement Window Frame for Single Sash (Frame Only)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
41mm Aluminium Casement Window Frame for Double Sash (Frame Only)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft
Supplying, Fabricating & Installing of 1.2mm thick 41mm deep Aluminium Casement window frame only. Rate to include for rubber beadings, rawl plugs, fasteners etc. Window sash, Fixed Panels, Louver Panels, hinges, locks paid separately. (Alumex extrusion Nos. CA-1007, CA-1008 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U647-U676 for window sashes-
41mm Aluminium Casement Window Frame for Single Sash with Top Fixed Panel (Frame Only)
41mm Aluminium Casement Window Frame for Single Sash with Both Side Fixed Panels (Frame Only)
41mm Aluminium Casement Window Frame for Single Sash with Top and Both Side Fixed Panels
41mm Aluminium Casement Window Frame for Double Sash with Top Fixed Panel (Frame Only)
BSR 2014- Department of Buildings
S07- 318
Description Item Unit
-DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
41mm Aluminium Casement Window Frame for 3 Sashes (Frame Only)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
41mm Aluminium Casement Window Frame for Double Sash with Both Side Fixed Panels (Frame Only)
41mm Aluminium Casement Window Frame for Double Sash with Top & Both Side Fixed Panels (Frame Only)
41mm Aluminium Casement Window Frame for 3 Sashes with Top Fixed Panel (Frame Only)
41mm Aluminium Casement Window Frame for 3 Sashes with Both Side Fixed Panels (Frame Only)
41mm Aluminium Casement Window Frame for 3 Sashes with Both Sides and Top Fixed Panels (Frame Only)
BSR 2014- Department of Buildings
S07- 319
Description Item Unit
41mm Aluminium Casement Window Frame for 4 Sashes (Frame Only)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
60mm Aluminium Casement Window Frame for Single Sash (Frame Only)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft
41mm Aluminium Casement Window Frame for 4 Sashes with Top Fixed Panel (Frame Only)
41mm Aluminium Casement Window Frame for 4 Sashes with Both Side Fixed Panels (Frame Only)
41mm Aluminium Casement Window Frame for 4 Sashes with Both Sides and Top Fixed Panels (Frame Only)
Supplying, Fabricating & Installing of 1.2mm thick 60mm deep Aluminium Casement window frame only. Rate to include for rubber beadings, rawl plugs, fasteners etc. Window sash, Fixed Panels, Louver Panels, hinges, locks paid separately. (Alumex extrusion Nos. CA 1009 & CA 1010 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U647-U676 for window sashes-
60mm Aluminium Casement Window Frame for Single Sash with Top Fixed Panel (Frame Only)
BSR 2014- Department of Buildings
S07- 320
Description Item Unit
-DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
60mm Aluminium Casement Window Frame for Double Sash (Frame Only)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
60mm Aluminium Casement Window Frame for 3 Sashes (Frame Only)
60mm Aluminium Casement Window Frame for Single Sash with Both Side Fixed Panels (Frame Only)
60mm Aluminium Casement Window Frame for Single Sash with Top & Both Side Fixed Panels (Frame Only)
60mm Aluminium Casement Window Frame for Double Sash with Top Fixed Panel (Frame Only)
60mm Aluminium Casement Window Frame for Double Sash with Both Side Fixed Panels (Frame Only)
60mm Aluminium Casement Window Frame for Double Sash with Top & Both Side Fixed Panels (Frame Only)
BSR 2014- Department of Buildings
S07- 321
Description Item Unit
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
60mm Aluminium Casement Window Frame for 4 Sashes (Frame Only)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft
60mm Aluminium Casement Window Frame for 3 Sashes with Top Fixed Panel (Frame Only)
60mm Aluminium Casement Window Frame for 3 Sashes with Both Side Fixed Panels (Frame Only)
60mm Aluminium Casement Window Frame for 3 Sashes with Both Sides and Top Fixed Panels (Frame Only)
60mm Aluminium Casement Window Frame for 4 Sashes with Top Fixed Panel (Frame Only)
60mm Aluminium Casement Window Frame for 4 Sashes with Both Side Fixed Panels (Frame Only)
BSR 2014- Department of Buildings
S07- 322
Description Item Unit
-DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft
60mm Aluminium Casement Window Frame for 4 Sashes with Both Sides and Top Fixed Panels (Frame Only)
Supplying, Fabricating & Installing of 1.2mm thick 70mm deep single sashed Matt Finished Aluminium Casement window frame only. Rate to include for rubber beadings, rawl plugs, fasteners etc. Window sash, Fixed Panels, Louver Panels, hinges, locks paid separately. (Alumex extrusion Nos. CA 1011 & CA 1012 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U647-U676 for window sashes-
70mm (1.2mm thick) Aluminium Casement Window Frame for Single Sash (Frame Only)
70mm (1.2mm thick) Aluminium Casement Window Frame for Single Sash with Top Fixed Panel (Frame Only)
70mm (1.2mm thick) Aluminium Casement Window Frame for Single Sash with Both Side Fixed Panels (Frame Only)
70mm (1.2mm thick) Aluminium Casement Window Frame for Single Sash with Top & Both Side Fixed Panels (Frame Only)
70mm (1.2mm thick) Aluminium Casement Window Frame for Double Sash (Frame Only)
BSR 2014- Department of Buildings
S07- 323
Description Item Unit
-DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
70mm (1.2mm thick) Aluminium Casement Window Frame for 3 Sashes (Frame Only)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
70mm (1.2mm thick) Aluminium Casement Window Frame for Double Sash with Top Fixed Panel (Frame Only)
70mm (1.2mm thick) Aluminium Casement Window Frame for Double Sash with Both Side Fixed Panels (Frame Only)
70mm (1.2mm thick) Aluminium Casement Window Frame for Double Sash with Top & Both Side Fixed Panels (Frame Only)
70mm (1.2mm thick) Aluminium Casement Window Frame for 3 Sashes with Top Fixed Panel (Frame Only)
70mm (1.2mm thick) Aluminium Casement Window Frame for 3 Sashes with Both Side Fixed Panels (Frame Only)
BSR 2014- Department of Buildings
S07- 324
Description Item Unit
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
70mm (1.2mm thick) Aluminium Casement Window Frame for 4 Sashes (Frame Only)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft
70mm (1.2mm thick) Aluminium Casement Window Frame for 3 Sashes with Both Sides and Top Fixed Panels (Frame Only)
70mm (1.2mm thick) Aluminium Casement Window Frame for 4 Sashes with Top Fixed Panel (Frame Only)
70mm (1.2mm thick) Aluminium Casement Window Frame for 4 Sashes with Both Side Fixed Panels (Frame Only)
70mm (1.2mm thick) Aluminium Casement Window Frame for 4 Sashes with Both Sides and Top Fixed Panels (Frame Only)
Supplying, Fabricating & Installing of 1.5mm thick 70mm deep single sashed Matt Finished Aluminium Casement window frame only. Rate to include for rubber beadings, rawl plugs, fasteners etc. Window sash, Fixed Panels, Louver Panels, hinges, locks paid separately. (Alumex extrusion Nos. CA 1013,CA 1014 & CA 1015 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U647-U676 for window sashes-
70mm (1.5mm thick) Aluminium Casement Window Frame for Single Sash (Frame Only)
BSR 2014- Department of Buildings
S07- 325
Description Item Unit
-DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
70mm (1.5mm thick) Aluminium Casement Window Frame for Single Sash with Top Fixed Panel (Frame Only)
70mm (1.5mm thick) Aluminium Casement Window Frame for Single Sash with Both Side Fixed Panels (Frame Only)
70mm (1.5mm thick) Aluminium Casement Window Frame for Single Sash with Both Side Fixed Panels (Frame Only)
70mm (1.5mm thick) Aluminium Casement Window Frame for Double Sash (Frame Only)
70mm (1.5mm thick) Aluminium Casement Window Frame for Double Sash with Top Fixed Panel (Frame Only)
70mm (1.5mm thick) Aluminium Casement Window Frame for Double Sash with Both Side Fixed Panels (Frame Only)
70mm (1.5mm thick) Aluminium Casement Window Frame for Double Sash with Top & Both Side Fixed Panels (Frame Only)
BSR 2014- Department of Buildings
S07- 326
Description Item Unit
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
70mm (1.5mm thick) Aluminium Casement Window Frame for 3 Sashes (Frame Only)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
70mm (1.5mm thick) Aluminium Casement Window Frame for 4 Sashes (Frame Only)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft
70mm (1.5mm thick) Aluminium Casement Window Frame for 3 Sashes with Top Fixed Panel (Frame Only)
70mm (1.5mm thick) Aluminium Casement Window Frame for 3 Sashes with Both Side Fixed Panels (Frame Only)
70mm (1.5mm thick) Aluminium Casement Window Frame for 3 Sashes with Both Sides and Top Fixed Panels (Frame Only)
70mm (1.5mm thick) Aluminium Casement Window Frame for 4 Sashes with Top Fixed Panel (Frame Only)
BSR 2014- Department of Buildings
S07- 327
Description Item Unit
-DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
70mm (1.5mm thick) Aluminium Casement Window Frame for 4 Sashes with Both Side Fixed Panels (Frame Only)
70mm (1.5mm thick) Aluminium Casement Window Frame for 4 Sashes with Both Sides and Top Fixed Panels (Frame Only)
BSR 2014- Department of Buildings
S07- 328
Description Item Unit
Aluminium Casement & Pivot Window (Frame Only)
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
Casement Window Sash Only
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
Supplying, Fabricating & Installing of 1.2mm thick 70mm deep single sashed Matt Finished Aluminium Casement & Pivot window frame only. Rate to include for rubber beadings, rawl plugs, fasteners etc. Window sash, Fixed Panels, Louver Panels, hinges, locks paid separately. (Alumex extrusion Nos. CA-1011,CA-1012 & PV-1001 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U647-U676 for window sashes-
70mm (1.2mm thick) Aluminium Casement & Pivot Window Frame for Single Sash (Frame Only)
70mm (1.2mm thick) Aluminium Casement & Pivot Window Frame for Single Sash with Top Fixed Panel (Frame Only)
70mm (1.2mm thick) Aluminium Casement & Pivot Window Frame for Single Sash with Both Side Fixed Panels (Frame Only)
Aluminium Casement Window Sash (Sash Only) for 41mm, 60mm or 70mm (1.2mm tk.) frames
Supplying, Fabricating & Installing of 1.2mm thick 40mm X 35mm (depth) Matt Finished Aluminium Casement window sash only. Rate to include for weather strips, casement locks, fasteners etc. Glass pans or Window panel boards paid separately. (Alumex extrusion No. CA-2005 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U677-U741 for window outer frame-
BSR 2014- Department of Buildings
S07- 329
Description Item Unit
Aluminium Casement Window Sash (Sash Only) for 70mm (1.5mm tk.) frame work
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
70mm (1.5mm tk.) Divided Casement Window Sash Only
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
Supplying, Fabricating & Installing of 1.5mm thick 54.5mm X 35mm (depth) Matt Finished Aluminium Casement window sash only. Rate to include for weather strips, casement locks, fasteners etc. Glass pans or Window panel boards paid separately. (Alumex extrusion No. CA-2007 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U677-U741 for window outer frame-
Aluminium Casement Divided Window Sash (Sash Divided to 2 portions) for 70mm (1.5mm tk.) frame work
Supplying, Fabricating & Installing of 1.5mm thick 62mm X 35mm (depth) Matt Finished Aluminium Casement Divided window sash consist of two portions. Rate to include for weather strips, casement locks, fasteners etc. Glass pans or Window panel boards paid separately. (Alumex extrusion Nos. CA-1116, CA-2008 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U677-U741 for window outer frame-
Aluminium Casement Divided Window Sash (Sash Divided to 4 portions) for 70mm (1.5mm tk.) frame work
Supplying, Fabricating & Installing of 1.5mm thick 62mm X 35mm (depth) Matt Finished Aluminium Casement Divided window sash consist of 4 portions. Rate to include for weather strips, casement locks, fasteners etc. Glass pans or Window panel boards paid separately. (Alumex extrusion Nos. CA-1116, CA-2008 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U677-U741 for window outer frame-
BSR 2014- Department of Buildings
S07- 330
Description Item Unit
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
70mm (1.2mm thick) Aluminium Casement & Pivot Window Sash Only
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
Aluminium Sliding windows1.3mm thick 70mm Aluminium Sliding windows
1.3mm thick 70mm 1 Sash Fixed, Single Sash Aluminium Sliding window
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
Aluminium Casement Divided Window Sash (Sash Divided to 6 portions) for 70mm (1.5mm tk.) frame work
Supplying, Fabricating & Installing of 1.5mm thick 62mm X 35mm (depth) Matt Finished Aluminium Casement Divided window sash consist of 6 portions. Rate to include for weather strips, casement locks, fasteners etc. Glass pans or Window panel boards paid separately. (Alumex extrusion Nos. CA-1116, CA-2008 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U677-U741 for window outer frame-
Supplying, Fabricating & Installing of 1.5mm thick 42.5mm X 40mm (depth) Matt Finished Aluminium Casement & Pivot window sash only. Rate to include for weather strips, casement locks, fasteners etc. Glass pans or Window panel boards paid separately. (Alumex extrusion No. PV-2001 or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories, U677-U741 for window outer frame-
Supplying, Fabricating & Fixing Matt finished Aluminium Window 1.3mm thick ,70mm depth Aluminium Framed (max. width 33.4mm) and Signal sash(max. width 56.2mm) Sliding Window. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 70S-1002, 70S-1202 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
BSR 2014- Department of Buildings
S07- 331
Description Item Unit
1.3mm thick 70mm Double Sashed Aluminium Sliding window
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft1.3mm thick 70mm 4 Sashed Aluminium Sliding window
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
Supplying, Fabricating & Fixing matt finished Aluminium window with 1.3mm thick ,70mm depth Aluminium framed (max. width 32.0mm) Double sash(max. width 36.2mm)Sliding Window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 70S-1001, 70S-1201-1, 70S-1101-1, 70S-1401, 70S-1501, 70S-1601, 70S-1701 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
1.3mm thick 70mm Double Sashed Aluminium Sliding window with 2 Fixed Panels at Top or Bottom
Supplying, Fabricating & Matt finished Aluminium Window with 1.3mm thick ,70mm depth Aluminium Framed (max. width 61.0mm) Double sash (max. width 56.2mm) Sliding Window with Two fixed panels on top to the window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately.(Alumex extrusion No. 70S-1012, 70S-1201-1, 70S-1101-1, 70S-1401, 70S-1501, 70S-1601, 70S-1701 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
Supplying, Fabricating & Fixing matt finished Aluminium Window with 1.3mm thick ,70mm depth Aluminium Framed (max. width 32.0mm) and Four Sliding Sashes(max. width 30.0mm) including necessary beadings, sliding locks etc. Glass pans, Window panel boards or Louver Panels paid separately.(Alumex extrusion No. 70S-1206, 70S-1001-1, 70S-1101-1, 70S-1401, 70S-1501, 70S-1601, 70S-1701 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
BSR 2014- Department of Buildings
S07- 332
Description Item Unit
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft1.5mm thick 80mm Aluminium Sliding window
1.5mm thick 80mm 1 Sash Fixed Single Sash Aluminium Sliding window
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft1.5mm thick 80mm Double Sashed Aluminium Sliding window
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
1.3mm thick 70mm 4 Sashed Aluminium Sliding window with 4 Sliding Panels at Top or Bottom
Supplying, Fabricating & Fixing Aluminium Window with 1.3mm thick ,70mm depth Aluminium Framed (max. width 60.0mm) Four Sliding Sashes(max. width 30.0mm) with Four Sliding panels on Top or Bottom of the Window including necessary beadings, sliding locks etc. Glass pans, Window panel boards or Louver Panels paid separately.(Alumex extrusion No. 70S-1201-1, 70S-1001-1, 70S-1006, 70S-1914, 70S-1401, 70S-1501, 70S-1601, 70S-1701 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
Supplying, Fabricating & Fixing Aluminium Window with 1.5mm thick ,80mm depth Aluminium Framed (max. width 43.5mm) Signal Sash (max. width 58.0mm) Sliding Window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately.(Alumex extrusion No. 80S-2001, 80S-2601, 80S-2602, 80S-2501, 80S-2102 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
Supplying, Fabricating & Fixing Aluminium Window 1.5mm thick, 80mm depth Aluminium Framed(max. width 37.6mm) Double Sash(max. width 58.0mm) Sliding Window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately.(Alumex extrusion No. 80S-2002, 80S-2101, 80S-2601, 80S-2501, 80S-2701 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
BSR 2014- Department of Buildings
S07- 333
Description Item Unit
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft
1.5mm thick 80mm Double Sashed Aluminium Sliding window with Fixed Panels at Top or Bottom
Supplying, Fabricating & Fixing Natural Anodized Aluminium Window with 1.5mm thick, 80mm depth Aluminium Framed (max. width 48.2mm)and Double Sash (max. width 58.0mm) Sliding Window with Two fixed panels on top or Bottom to the window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 80S-2001, 80SFL-1001, 80SFL-1002, 80SFL-1003, 80S-2101, 80S-2501, 80S-2601, 80S-2701 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
1.5mm thick 80mm Double Sashed Aluminium Sliding window with 2 Fixed Panels at Both Sides
Supplying, Fabricating & Fixing Aluminium Window 1.5mm thick, 80mm depth Aluminium Framed (max. width 66.0mm) Double sash (max. width 55.0mm) Sliding Window with Two fixed panels at sides of the window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 80S-2001, 80SFL-1001, 80SFL-2102, 80SFL-1003, 80S-2101, 80S-2501, 80S-2601, 80S-2701, 80S-2302 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
1.5mm thick 80mm Double Sashed Aluminium Sliding window with 2 Top Hang Sashes at Top or Bottom
Supplying, Fabricating & Fixing Aluminium Window 1.5mm thick, 80mm depth Aluminium Framed(max. width 48.2mm) Double sash (max. width 58.0mm) Sliding Window with Two Hung panel sashes on top or bottom to the window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 80S-2001, 80SFL-1001, 80SFL-1002, 80SFL-1003, 80S-2101, 80S-2501, 80S-2601, 80S-2701, 80S-2101 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
BSR 2014- Department of Buildings
S07- 334
Description Item Unit
-DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft1.5mm thick 80mm 6 Sashed Aluminium Sliding window
-DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO-Bronzed Anodized Aluminium sq.ft
1.5mm thick 80mm 4 Sashed Aluminium Sliding window with 4 Sashes Sliding Panels at Top or Bottom
Supplying, Fabricating & Fixing Aluminium Window with 1.5mm thick, 80mm depth Aluminium Framed (max. width 62.0mm) Four Sliding Sashes(max. width 58.0mm) with Four Sliding panels on top or bottom of the Window including necessary beadings, sliding locks etc. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 80S-2001, 80SFL-1001, 80S-2201, 80S-2301, 80S-2101, 80S-2501, 80S-2601, 80S-2701, 80S-2101 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
1.5mm thick 80mm 4 Sashed Aluminium Sliding window with 2 Fixed Panels at Both Sides
Supplying, Fabricating & Fixing Aluminium Window with 1.5mm thick ,80mm depth Aluminium Framed (max. width 63.0mm) Four Sliding Sashes(max. width 55.0mm) with two fixed panels at both sides Window including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 80S-2001, 80SFL-1001, 80S-2201, 80S-2301, 80S-2101, 80S-2501, 80S-2601, 80S-2701, 80S-2101 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
Supplying, Fabricating & Fixing Aluminium Window with 1.5mm thick ,80mm depth Aluminium Framed (max. width 37.6mm) Six Sashes Sliding Window(max. width 63.0mm) including necessary beadings, sliding lock etc. Glass pans, Window panel boards or Louver Panels paid separately. (Alumex extrusion No. 80S-2001, 80SFL-1001, 80S-2201, 80S-2301, 80S-2101, 80S-2501, 80S-2601, 80S-2701, 80S-2101 & etc. or equivalent) -Refer U001 to U016 for glass & boards, U017 to U051 for louvers, U743-U764 for accessories-
BSR 2014- Department of Buildings
S07- 335
Description Item Unit
-DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
BSR 2014- Department of Buildings
S07- 336
Description Item Unit
Aluminium composite cladding
sq.ftDoor lock for Aluminium Doors
Nos
Nos
Nos
Nos
NosSliding lock for Aluminium door
Nos Stainless Steel Door Handle for Aluminium Doors
NosFloor hinge
Nos
Nos
NosHinges (Stainless Steel) for Aluminium Doors
pairsDoor Closer
Supplying, fabricating and installing of 4.0mm thick Aluminium composite cladding panel (Alucobond or equivalent European make) with open joint tray panel system using non corrosive 50x81x3mm tk. Aluminium "T" channel section (al 217), non corrosive 50x50x3mm pressed Aluminium "U" wall bracket sub frame and AL 201 & AL 202 profiles on tray panel, Rate to include for ss nut and bolts, ss screws, blind rivets, U channels, Nylon resistant, Anchor bolts, and other necessary accessories. Bird mesh to be provided in side of vent areas, all complete as per manufacture's specifications. (8 % attendance fee included)
Supplying and Fixing UNION Door lock (No-X 920,X925 or X930) for Aluminium Door with necessary accessories to working order. ( Prime Cost of a door lock Rs.3380/=)
Supplying and Fixing Door lock (No-VR50101B) for Aluminium Door with necessary accessories to working order. ( Prime Cost of a door lock Rs.5100/=)
Supplying and Fixing Door lock (No-VR50101C) for Aluminium Door with necessary accessories to working order. ( Prime Cost of a door lock Rs.5640/=)
Supplying and Fixing Door lock (Alpha) for Aluminium Door with necessary accessories to working order. ( Prime Cost of a door lock Rs.617/=)
Supplying and Refixing Door lock Cylinder (Alpha) for Aluminium Door with necessary accessories to working order. ( Prime Cost of a door lock Rs.375/=)
Supplying and Fixing Sliding lock for Aluminium door with necessary accessories . ( Prime Cost of a Sliding door Lock Rs.690/=)
Supplying and Fixing Stainless Steel Door Handle for Aluminium door with necessary accessories . ( Prime Cost of a door Handle Rs.1500/=)
Supplying and Fixing of UNION floor hinges (No: 8300) with necessary accessories .(Imported, British or south African make), ( Prime Cost of a floor hinge Rs.21,200/=)
Supplying and fixing imported floor hinges (new star) of approved quality including chipping of existing floors and making good after completion. ( Prime Cost of a floor hinge Rs.16,500/=)
Supplying and Fixing of VVP floor hinges with necessary accessories .(Imported, British or south African make), ( Prime Cost of a floor hinge Rs.9,500/=)
Supplying and fixing UNION Butt Hinges, , 4"x3"x 2mm (thick) stainless steel, for Aluminium doors with pop rivets.
BSR 2014- Department of Buildings
S07- 337
Description Item Unit
Nos
Nos
Supplying and fixing door closer (new star) with necessary accessories ( Prime Cost of a door Handle Rs.2350/=)
Supplying and fixing door closer (Union or Yale) with necessary accessories ( Prime Cost of a door closer Rs.6424/=)
BSR 2014- Department of Buildings
S07- 338
Description Item Unit
pairs
pairs
pairs
pairs
pairs
pairs
pairs
pairs
pairsHot dip GI interlocking ceiling frame work only
sq.ftMineral fiber suspended ceiling
sq.ft Mineral fiber Suspended ceiling
sq.ft
Supplying and fixing 8" bar hingers for casement windows with necessary accessories ( Prime Cost Rs.250)
Supplying and fixing 10" bar hingers for casement windows with necessary accessories ( Prime Cost Rs.277)
Supplying and fixing 12" bar hingers for casement windows with necessary accessories ( Prime Cost Rs.340)
Supplying and fixing 14" bar hingers for casement windows with necessary accessories ( Prime Cost Rs.411)
Supplying and fixing 16" bar hingers for casement windows with necessary accessories ( Prime Cost Rs.590)
Supplying and fixing 18" bar hingers for casement windows with necessary accessories ( Prime Cost Rs.733)
Supplying and fixing Casement Handel (04 hole) for windows with necessary accessories ( Prime Cost Rs.215)
Supplying and fixing Crescent Lock for sliding windows with necessary accessories ( Prime Cost Rs.143)
Supplying and fixing Magnetic Door Catcher (Plastic) with necessary accessories (prime Cost Rs.161)
The frame members for suspended ceiling are in a standard kit (CKM or equivalent). Main runners ( 38mmx24mmx3660mm) are fixed at 1220 centers securely suspended using 4mm dia. GI hanging rod to the structural soffit or timber roof, using an appropriate suspension at 1220mm centers, Cross Tees (27mmx24mmx1220mm) of 1220mm length to be fixed between the main runners at 610mm centers and another cross tees (27mmx24mmx610mm) fixed at mid span between 610mm to form a grid structure of 610mmx 610mm in size. wall angles (24mmx24mmx3050mm) are fixed at wall edges. ( Edge molding and painting paid separately)
Supplying & fixing of 2' 0"x2' 0"& 15mm thick (Mineral fiber) ceiling boards lay on hot dip GI pre engineered interlocking ceiling frame work. The frame members for suspended ceiling are in a standard kit (CKM or equivalent). Main runners ( 38mmx24mmx3660mm) are fixed at 1220 centers securely suspended using 4mm dia adjustable GI hanging rod with spring clips to the structural soffit or existing roof structure, using an appropriate suspension at 1220mm intervals along each Main runners. Cross Tees (27mmx24mmx1220mm) of 1220mm length to be fixed between the main runners at 610mm centers and another cross tees (27mmx24mmx610mm) fixed at mid span between 610mm to form a grid structure of 610mmx 610mm in size. wall angles (24mmx24mmx3050mm) are fixed at wall edges.
Supplying & fixing 4' -0"x 2' -0"x 1/2"thick Mineral fiber ceiling boards lay on Existing interlock type ceiling frame work , forming a panel side of 2' 0" X 2' 0", and at the average elevation of 12' 0" from the working floor, (for 12 nos or 96 ft2)
BSR 2014- Department of Buildings
S07- 339
Description Item Unit
sq.ft
sq.ftSuper Flex Suspended ceiling
sq.ft
sq.ftGypsum board suspended ceiling
sq.ftMetal ceiling
sq.ft
Supplying and installing mineral fiber Japanese make suspended exposed ceiling system, using 4' 0" x 2' 0"' X 15 mm thick ceiling boards, lay on white colour interlock type, hot dip GI grid system , forming a panel side of 4' 0" x 2' 0"',and suspended on 4mm dia. adjustable rods with spring clip to soffit of concrete or timber roofs. ( Edge molding paid separately)
Supplying and installing mineral fiber Japanese make suspended exposed ceiling (Reveal edge) system, using 605 mm X 605 mm X 15 mm white colour ceiling boards lay on white colour interlock type hot dip GI grid system , forming a panel side of 610mmx610mm,and suspended on 4mm rods with spring clip to soffit of concrete or timber roofs. . ( Edge molding & Painting paid separately)
Supplying and installing Super Flex (Plain) suspended ceiling system, using 4 ft X 4 ft X 3.2 mm ceiling boards lay on white colour interlock type hot dip GI grid system , forming a panel side of 2ft X2 ft , and suspended on 4mm rods with spring clip to soffit of concrete or timber roofs. ( Edge molding & Painting paid separately)
Supplying and installing Super Flex (with design) suspended ceiling system, using 4 ft X 4 ft X 3.2 mm ceiling boards in white colour interlock type hot dip GI grid system , forming a panel side of 2ft X2 ft, and suspended on 4mm rods with spring clip to soffit of concrete or timber roofs ( Edge molding & Painting paid separately)
Supplying and fixing gypsum board suspended ceiling . using 2 ft x 2ft X 9 mm. thick ceiling boards in white colour interlock type hot dip GI grid system , forming a panel side of 610mmx610mm, and suspended on 4mm GI hanging rods with spring clip to soffit of concrete or timber roofs ( Edge molding & Painting paid separately)
Supply and installation of concealed type metal false ceiling, at an average elevation of 12' from the working floor Including revel edge of 2' 0" X 2' 0" size 0.5mm minimum thickness, epoxy powder painted steel Tiles (paint film thickness of average 80microns ) suspended to the roof frame work with, 0.3 mm thick pre painted hot dip galvanized, 15mm x 38mm plain TEE-grid bars and 20mm x 24mm wall angles, suspended with adjustable burrerfly clip, 4mm dia. surface treated galvanized steel hanger rods, complete with necessary anchor bolts and any other accessories. (All in accordance with the approved shop drawings, to the Engineers' satisfaction. )
Prime cost of Concealed type metal false ceiling, 600mm x 600mm size 0.5mm minimum thickness, epoxy powder painted steel Tiles. Rs.790 **(2641)
BSR 2014- Department of Buildings
S07- 340
Description Item Unit
sq.ft
Partitioning (Gypsum board)
sq.ftRemoving and fixing an Aluminium door Removing existing Aluminium door with frame and fixing at new position. sq.ftAluminium, Ceiling panels (Pinholes)
sq.ftAluminium, partitions with available extrusions
sq.ftRoller Shutter door, Aluminium
sq.ft
Supply and installation of lay in type "E-Metallic Aluminium ceiling, at an average elevation of 12' from the working floor, Including revel edge of 2' 0" X 2' 0"mm size 0.7mm average thickness, 80 microns high quality powder coated Aluminium perforated or plain ceiling panels, suspended to the roof frame work with hot dip galvanized "T" bars of 14mm x 38mm and wall angles of 19mm x 24mm suspended with, adjustable burrerfly clip, 04mm GI hanging roads, anchor bolts and all other accessories. (All in accordance with the approved shop drawings, to the Engineers' satisfaction. )
Prime cost of E-Metallic high quality powder coated Aluminium perforated or plain ceiling Tiles. ( 600mm x 600mm size) Rs.908 **(2641)
Supplying and fixing gypsum board partitioning with GI channel member frame work fixed onto walls and floors , 1/2" thick gypsum board fixed to both sides of frame work complete with making joints using joint tape and gypsum compound to get wall finish. Rate to include for applying one coat of acrylic wall filler to boards.
Supplying, fixing Aluminium 2'-0" x2'-0" ceiling panels (Pinholes) with Aluminium frame work and adjustable. Prime cost of Pinholes Ceiling suspended type 600mm x 600mm size Rs.665
Fixing available Aluminium partition with using new GI channels and new rubber beadings, prop rivets, screws, nails, etc..
Supplying and fixing of a Aluminium Roller Shutter door, having a maximum clear width of 20' and 1.1mm thick Natural anodized Aluminium slats, center bar pulleys, side plates with necessary racers, fabricating mechanical winding box with m.s square tube and covering the box with metallic sheets, fixing on site with bottom bars and G.I, u-channels for vertical guides at two vertical edges, which are painted with two coats of anticorrosive paint and two coats of enamel paint, hard rubber beading embedded in the guide bars to minimize sound & rough flow of the shutter. Pulling rod and chain to be provided for manual rolling operation. (Additional length of 5" to two sides horizontally and 18" to upper end inside the mechanical box as initial winding vertically to be added to the clear opening area). ( 8% attendance fee Considered)
BSR 2014- Department of Buildings
S07- 341
Description Item Unit
Roller door, Aluminium, Zn/Alu
sq.ftRoller shutter door motor
NosAluminium Fixed Glass Windows
41mm Aluminium Fixed Glass Window Frame Only -DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
60mm Aluminium Fixed Glass Window Frame Only -DO- Matt Finished Aluminium sq.ft -DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
70mm Aluminium Fixed Glass Window Frame Only -DO- Matt Finished Aluminium sq.ft
Supplying and fixing of a Zn/Alu Roller door, having a maximum clear width of 20' and consisting of 0.6mm thick Zn/Al covering sheet, center bar pulleys, side plates with necessary racers, fabricating mechanical winding box with m.s square tube and covering the box with metallic sheets, fixing on site with bottom bars and G.I, u-channels for vertical guides at two vertical edges, which are painted with two coats of anticorrosive paint and two coats of enamel paint to match the colour of door sheeting, and sound reduction rubber beading embedded in the guide bars. Pulling rod and chain to be provided for manual rolling operation. (Additional length of 9" to two sides horizontally and 18" to upper end inside the mechanical box as initial winding vertically to be added to the clear opening area). ( 8% attendance fee Considered)
Supplying roller shutter door motor, 0.5Hp, 300w, 2.5A sing-phase, 1780 rpm and 54:1 gear ratio, with two remote controllers for auto operation. ( 8% attendance fee Considered)
Supplying, Fabricating & Installing of 1.2mm thick 41mm deep Aluminium Fixed Glass window frame only. Rate to include for rawl plugs, fasteners etc. Glass Panels, Louver Panels, paid separately. (Alumex extrusion Nos. CA-1007 or equivalent) - Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
Supplying, Fabricating & Installing of 1.2mm thick 60mm deep Aluminium Fixed Glass window frame only. Rate to include for rawl plugs, fasteners etc. Glass Panels, Louver Panels, paid separately. (Alumex extrusion Nos. CA-1009 or equivalent)- Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
Supplying, Fabricating & Installing of 1.2mm thick 70mm deep Aluminium Fixed Glass window frame only. Rate to include for rawl plugs, fasteners etc. Glass Panels, Louver Panels, paid separately. (Alumex extrusion Nos. CA-1011 or equivalent)- Refer U001 to U016 for glass & boards, U017 to U051 for louvers-
BSR 2014- Department of Buildings
S07- 342
Description Item Unit
-DO- Natural Anodized Aluminium sq.ft -DO- Bronzed Anodized Aluminium sq.ft -DO-Powder Coated Aluminium sq.ft -DO-Wood Finished Aluminium sq.ft
--- The End ---
BSR 2014- Department of Buildings
S07- 343
BSR Rate
A-DEMOLISHER
1,1751,565
1,368
153489
6,956
5,024
556
602
656
696
966
113
170
91616
37580
77333
510
Author: Eng. D.N.Ranaweera
BSR 2014- Department of Buildings
S07- 344
BSR Rate
13
29
290
870
1,305
1,108
1,437
1,823
2,1551,5651,546
387
588
783
1,546
1,827
2,217
5
8
1,100
2,842
BSR 2014- Department of Buildings
S07- 345
BSR Rate
6,526
BSR 2014- Department of Buildings
S07- 346
BSR Rate
115
398
1,752
7,960
15,920
779
BSR 2014- Department of Buildings
S07- 347
BSR Rate
B-EXCAVATOR
1,256
773
1,739
2,705
2,319
1,932
2,874232
7734,810
3,517
1,117
1,310
934
1,407
5,636
BSR 2014- Department of Buildings
S07- 348
BSR Rate
16,541
108
192
216
BSR 2014- Department of Buildings
S07- 349
BSR Rate
C-CONCRETER
36,325
32,482
33,829
36,576
36,563
40,019
564
1,013
43,299
43,556
76
114
639
314
514
216
BSR 2014- Department of Buildings
S07- 350
BSR Rate
283
368
451
375
510
614576
194
210
184
1,721
45,145
46,690
47,463
44,471
46,016
46,789
14,888
19,551
47,170
BSR 2014- Department of Buildings
S07- 351
BSR Rate
47,943
48,715
49,488
48,715
51,807
53,352
15,260
160
117
116
91
233
184
BSR 2014- Department of Buildings
S07- 352
BSR Rate
219
BSR 2014- Department of Buildings
S07- 353
BSR Rate
D-BRICKLAYER41,152
34,393
36,074
16,36512,81013,660
6,65025,171
37,707
19,91937,97759,931
1,392
3,787
619
1,469
253
353
533
271
482
156
697
462
BSR 2014- Department of Buildings
S07- 354
BSR Rate
508
368
293
33,93236,72737,90640,224
BSR 2014- Department of Buildings
S07- 355
BSR Rate
E-MASON
28,59130,523
24,675
14,691
19,520
26,350
17,586
25,310
33,207
56,721
BSR 2014- Department of Buildings
S07- 356
BSR Rate
F-PAVIOR19
43
15,328
11,431
14,433
32,932
1,475
100999594
208
274304
359307318
BSR 2014- Department of Buildings
S07- 357
BSR Rate
352494428440
339333313
483517529
378365
276
378
519
314
293
29,100
294
BSR 2014- Department of Buildings
S07- 358
BSR Rate
211
BSR 2014- Department of Buildings
S07- 359
BSR Rate
332294297292
99240252288288
264
319
314
309
365
387
98104
323
488
BSR 2014- Department of Buildings
S07- 360
BSR Rate
352
460
1,106
1,902
129
1,226
55
280
155
194
374
346
BSR 2014- Department of Buildings
S07- 361
BSR Rate
302
226
342
BSR 2014- Department of Buildings
S07- 362
BSR Rate
G-ROOFER
3,009
33,890
29,550
11,412
28,075
28,584
10,875
13,880
200
35,249
35,883
5,397
BSR 2014- Department of Buildings
S07- 363
BSR Rate
129
33
161
65
160
129
101
179
116
376
325
205
136
153
562
392
2,048
73
BSR 2014- Department of Buildings
S07- 364
BSR Rate
64
89
707,471
387
176
274
49527
27
26
30
2914,684
773580258
7,728
343497748932
298
BSR 2014- Department of Buildings
S07- 365
BSR Rate
374
97
110
266
697
434
566
619
BSR 2014- Department of Buildings
S07- 366
BSR Rate
H-CARPENTER & JOINER
151
124
51
87
55
30
228
234
160
163
65
38,917
32,892
1,116
6,176
BSR 2014- Department of Buildings
S07- 367
BSR Rate
721,968
12,121
12,571
10,546
13,122
1,660194
34,791
37,303
476
553
551
534
BSR 2014- Department of Buildings
S07- 368
BSR Rate
45
1,119
1,257
170
65
188
231
1,228
936
710
597
1,345
994
1,262
1,079
BSR 2014- Department of Buildings
S07- 369
BSR Rate
715
578
765
621
912
1,212
998
931
738
1,103
635
675
1,410339129
749
3,698
252
224
BSR 2014- Department of Buildings
S07- 370
BSR Rate
749451
893
BSR 2014- Department of Buildings
S07- 371
BSR Rate
532
243
893
798
479
689
2,009
1,549
1,318
1,555
1,330
2,011
891
BSR 2014- Department of Buildings
S07- 372
BSR Rate
831
824
57
93
1,189
969
588
1,087
1,031
133
151
209
910
1,284
62
BSR 2014- Department of Buildings
S07- 373
BSR Rate
62
36
46
405
42,704
30,022
53,462
41,268
753
793
44
136
166
1,001
6118,115
5,745
3,993
BSR 2014- Department of Buildings
S07- 374
BSR Rate
4,979
3,227
34
36
39
4671
100
1,076
851
980
BSR 2014- Department of Buildings
S07- 375
BSR Rate
J-IRONMONGER
6275
114
200
114
121200255293341380
1,439
813
103
362
343
464889
140146
250283
91
BSR 2014- Department of Buildings
S07- 376
BSR Rate
494
2892,316
474
175
47
246
1,081
223
237
252
1,851
443
481
582
677229
896
1,552
2,044
2,754
BSR 2014- Department of Buildings
S07- 377
BSR Rate
638
664
690
821
847
898
1,108
4,326
3,408
440
105
387314279419
1,010
1,300
1,268
1,4931,374
11,580
11,129
1,945
BSR 2014- Department of Buildings
S07- 378
BSR Rate
1,495
109
150
1,153246
165
54
312
240
315
11,580
11,129
776
125
98
215
BSR 2014- Department of Buildings
S07- 379
BSR Rate
382
1,534
1,398
2,279
90,397
92,333
94,660
95,796
97,541
103,916
BSR 2014- Department of Buildings
S07- 380
BSR Rate
106,113
107,165
109,424
112,554
114,952
125,508
109,301
111,832
113,319
115,833
118,331
BSR 2014- Department of Buildings
S07- 381
BSR Rate
K-BRASS FOUNDER
65
255
268
332
320
416383421460540
280
305
357
421
460
486
512
397365391
268
539
318
BSR 2014- Department of Buildings
S07- 382
BSR Rate
286249
638
896
1,352
1,365
1,455
556839
1,352
734
808458
1,762772
451
329302455
365274
1,300
1,139
1,590
BSR 2014- Department of Buildings
S07- 383
BSR Rate
8,299
11,411
2803,0923,993
5,377
8,855
4,899
5,152
4,3962,731
BSR 2014- Department of Buildings
S07- 384
BSR Rate
L-PLASTERER
4,425
5,0693,910
5,3842,802
63
35
86
61
98135
47
224
5,8932871
3,7873,9683,2613,4415,0245,3334,5364,721
663
1,180
BSR 2014- Department of Buildings
S07- 385
BSR Rate
1,180
BSR 2014- Department of Buildings
S07- 386
BSR Rate
5,900
6,827
81
99
8,086
95111
BSR 2014- Department of Buildings
S07- 387
BSR Rate
M-TINKER
354
567
554
2387488
26
388
179
474
427
213
529495
11
1,108
5,032
3,140
3,883
BSR 2014- Department of Buildings
S07- 388
BSR Rate
2,206
262379
733
708
1602,813
487
1,726
1,866
511
339
480
276
539
305
1,200
726
BSR 2014- Department of Buildings
S07- 389
BSR Rate
N-GLAZER
112
182
234
310
220
28
BSR 2014- Department of Buildings
S07- 390
BSR Rate
P-PAINTER & DECORATOR
1,082
194
1,829
1,301
1,610
1,907
21
239
405301
218
384
261
BSR 2014- Department of Buildings
S07- 391
BSR Rate
306
462
501
2,626
2,819
1,648
1,201
1,814
1,984
2,061
4,876
1,356
1,796
1,405
2,553
1,688
2,862
2,013
3,766
BSR 2014- Department of Buildings
S07- 392
BSR Rate
2,362
3,876
2,986
4,593
3,487
3,015
1,748
2,794
2,449
2,562
4,935
3,694
6,410
967
2,808
3,655
BSR 2014- Department of Buildings
S07- 393
BSR Rate
1,3548
15
BSR 2014- Department of Buildings
S07- 394
BSR Rate
1,822
3,413
1,36917
902
1,669
5,302
1,215
3,143
1,797
3,133
2,211
3,944
5,668
4,080
5,804
1,732
6,561
2,164
BSR 2014- Department of Buildings
S07- 395
BSR Rate
6,067
BSR 2014- Department of Buildings
S07- 396
BSR Rate
1021,773
44
200
111
BSR 2014- Department of Buildings
S07- 397
BSR Rate
Q-PLUMBER
290419442
679129
1781,0281,3882,359
3,642278
2,607
5,796
2,639
2,1058,324
23,589
12,526
6,730
1,236
BSR 2014- Department of Buildings
S07- 398
BSR Rate
1,952
2,771
3,655
4,599
6,023
10,621
1,406
2,392
3,774
4,576
5,228
8,646
11,602
18,541
22,492
43,807
2,2152,9864,6258,258
18,22035,111
2,1343,9634,682
BSR 2014- Department of Buildings
S07- 399
BSR Rate
738
1,028
1,202
1,382
1,627
2,174
2,760
1,041
6,238
4,776
7,243
5,947
1,099
3,407
2,634
9,718
108237302
BSR 2014- Department of Buildings
S07- 400
BSR Rate
340533643643900
BSR 2014- Department of Buildings
S07- 401
BSR Rate
2,065
1,516
11,725
8,087
3,671
40,992
43,565
23,540
27,082
BSR 2014- Department of Buildings
S07- 402
BSR Rate
40,786
35,676
38,935
91,099
81,767
83,216
BSR 2014- Department of Buildings
S07- 403
BSR Rate
82,490
45,517
60,895
47,338
59,208
12,710
12,595
4,749
BSR 2014- Department of Buildings
S07- 404
BSR Rate
4,654
1,875
1,981
2,431
4,254
25,192
23,183
3,570
10,255
3,469
23,468
9,490
8,331
BSR 2014- Department of Buildings
S07- 405
BSR Rate
BSR 2014- Department of Buildings
S07- 406
BSR Rate
4,660
1,203
2,607
1,063
3,535
1,359
12,025
13,493
22,638
10,288
31,564
21,904
47,262
40,017
2,430
BSR 2014- Department of Buildings
S07- 407
BSR Rate
6,193
5,410
5,871
5,281
3,494
3,182
4,323
13,452
23,379
47,182
8,325
25,209
BSR 2014- Department of Buildings
S07- 408
BSR Rate
29,047
9,968
11,774
21,641
21,262
21,987
BSR 2014- Department of Buildings
S07- 409
BSR Rate
43,118
20,779
28,024
8,386
4,982
5,111
9,411
20,581
BSR 2014- Department of Buildings
S07- 410
BSR Rate
23,801
9197
140
516
580
966
2,898
3,156
825
10138
117230
819
2,494
BSR 2014- Department of Buildings
S07- 411
BSR Rate
2,853
3,279
308
372
408
503
393
434
4,533
989
1,300
BSR 2014- Department of Buildings
S07- 412
BSR Rate
BSR 2014- Department of Buildings
S07- 413
BSR Rate
2,575
2,008
546
531
4,652
1,2701,174
2,019
421
497
614
497
BSR 2014- Department of Buildings
S07- 414
BSR Rate
771
858
1,934
1,981
381
426
236
2,137
3,779
2,523
822
1,2051,5652,0812,725
BSR 2014- Department of Buildings
S07- 415
BSR Rate
3,6585,7472,531
294294332525603757796139177
3,2851,868
173211263353372469
610
4,6731,704
6,408
1,393
993
2,696
335605
1,569
2727293335
BSR 2014- Department of Buildings
S07- 416
BSR Rate
13
11915722226129941529
14517323527331240954
161
204
233
315
343
467
573
775
34
46
BSR 2014- Department of Buildings
S07- 417
BSR Rate
2586
46
63
63757
25
93719
174200238290406444
14318221424731137548116919223425930737153
11,841
3,269
BSR 2014- Department of Buildings
S07- 418
BSR Rate
4,948
3,761
4,060
471858
1,282
8,952
10,614
18,677
19,901
14,980
24,902
46,394
89,774
156,911
BSR 2014- Department of Buildings
S07- 419
BSR Rate
2,898
199224256347475701
2,7463,4674,2326,0783,446
20,346
1,203
817
6,777
2,882
6,200
851
BSR 2014- Department of Buildings
S07- 420
BSR Rate
1,674
4,224
3,231
946
2,798
2,437
3,625
4,720
9,292
92
BSR 2014- Department of Buildings
S07- 421
BSR Rate
446453453525
636
2,710
BSR 2014- Department of Buildings
S07- 422
BSR Rate
2,973
2,174
4,634
194290
39
7388
105185271417
1,730
587888
114180232619
6983
116
163185
216
8898
152
225
BSR 2014- Department of Buildings
S07- 423
BSR Rate
353541
1,688
627588
116154231637
658083
127152185522
587083
107141172522
683748
1,2632,1002,7443,5813,903
361
490
490
812
966
BSR 2014- Department of Buildings
S07- 424
BSR Rate
1,714
2,473
BSR 2014- Department of Buildings
S07- 425
BSR Rate
6488
111160243304842
677671
109137186666627588
116154231653
20
47
100
131
171
275
784
26
35
45
BSR 2014- Department of Buildings
S07- 426
BSR Rate
70
87
25
59
121
160
209
339
228274326519567
364
339
674
1,2682,537
4,140
6,10928,233
51,249
BSR 2014- Department of Buildings
S07- 427
BSR Rate
921
33,025
30,024
20,684
23,338
33,951
207427
9,773
377
561
323
351
240
BSR 2014- Department of Buildings
S07- 428
BSR Rate
198
142
BSR 2014- Department of Buildings
S07- 429
BSR Rate
R-DRAIN LAYER
4,5835,695
976
10,311
17,334
28,591
12,771
17,744
20,902
26,721
14,436
18,938
22,058
BSR 2014- Department of Buildings
S07- 430
BSR Rate
27,387
BSR 2014- Department of Buildings
S07- 431
BSR Rate
19,440
22,189
26,317
27,868
1,372
11,053
23,271
206
355419
483612
677
963
739
884
673
963979
BSR 2014- Department of Buildings
S07- 432
BSR Rate
1,088
1,167
1,286
1,126
1,027
393
480
555
858537
592
689
786
545
704
362
435
369
435
480
513
580
BSR 2014- Department of Buildings
S07- 433
BSR Rate
536
514
589
275
354
605
698
735
911
952
1,074
1,446
1,489
1,609
BSR 2014- Department of Buildings
S07- 434
BSR Rate
4,085
BSR 2014- Department of Buildings
S07- 435
BSR Rate
S-MISCELLANEOUS
76
9427325
18,219
36,741
39
24
1,127
11
11
11
11
14
4
4
BSR 2014- Department of Buildings
S07- 436
BSR Rate
4
5
247
1,395
1,731
8,668
346578
448
232
310
387
1,361
157
186
13
BSR 2014- Department of Buildings
S07- 437
BSR Rate
356
BSR 2014- Department of Buildings
S07- 438
BSR Rate
421
666
114
55
5,1525,1524,6374,6374,6374,6379,145
6,7625,1523,7363,7363,7363,736
355355451838548
1,932
5,861
6,634
7,922
7,922
1,127
BSR 2014- Department of Buildings
S07- 439
BSR Rate
1,623
2,709
1,621
3,910
1,161
773902
1,031
1,160
20222123
49
5
4
61
BSR 2014- Department of Buildings
S07- 440
BSR Rate
T-ELECTRICAL INSTALLATIONS
BSR 2014- Department of Buildings
S07- 441
BSR Rate
3,6973,8933,8005,9573,8804,085
5,3816,136
8,277
4,1724,3684,2746,6564,3544,547
5,8456,7088,984
13,916
15,628
18,153
BSR 2014- Department of Buildings
S07- 442
BSR Rate
20,321
22,582
24,588
18,183
19,895
22,875
25,137
27,683
29,396
31,957
50,319
56,518
93,214
22,691
3,452
4,224
9,613
10,523
6,719
9,297
14,426
BSR 2014- Department of Buildings
S07- 443
BSR Rate
17,288
BSR 2014- Department of Buildings
S07- 444
BSR Rate
227507520855
1,3882,0372,980
627950
1,3552,2083,1624,9226,314
661813
1,4871,9032,5605,8142,0632,9804,707
7,4258,548
10,93414,09318,65622,23627,290
247507606946
1,398
BSR 2014- Department of Buildings
S07- 445
BSR Rate
2,0733,291
7091,0961,5852,5763,5545,1756,838
6,056
1,0681,675
10,226
7,430
13,415
16,320
14,339
8,5313,813
5,796
2,384
6,852
6,483
9,784
6,852
9,784
BSR 2014- Department of Buildings
S07- 446
BSR Rate
6,483
7,536
6,2494,629
782809905
376524710980
1,1781,3471,6051,643
6451,956
8,752
8,531
8,531
9,460
10,853
12,027
642229
BSR 2014- Department of Buildings
S07- 447
BSR Rate
617207
8796
109164212277
7682
213263271524515
1,020531
1,0571,2091,3241,4801,7812,2343,1223,711
1,0941,2361,4311,630
20,16625,721
BSR 2014- Department of Buildings
S07- 448
BSR Rate
U-ALUMINIUM FABRICATOR
194
322
22
293
322
341
370
122
BSR 2014- Department of Buildings
S07- 449
BSR Rate
151
BSR 2014- Department of Buildings
S07- 450
BSR Rate
141
171
170
200
148
178
258
9391,0021,0371,1421,650
878972991
1,107
BSR 2014- Department of Buildings
S07- 451
BSR Rate
1,391
BSR 2014- Department of Buildings
S07- 452
BSR Rate
1,2361,3751,4031,5752,067
1,2591,3291,3531,5212,062
862913929
1,0441,412
847723
1,0042,476
BSR 2014- Department of Buildings
S07- 453
BSR Rate
776
BSR 2014- Department of Buildings
S07- 454
BSR Rate
1,5871,3281,9034,9171,420
272282284301359
389412418447570
BSR 2014- Department of Buildings
S07- 455
BSR Rate
289303307326415
243251254268310
BSR 2014- Department of Buildings
S07- 456
BSR Rate
270281284299362
351371377402507
BSR 2014- Department of Buildings
S07- 457
BSR Rate
240249251264318
292307310329413
BSR 2014- Department of Buildings
S07- 458
BSR Rate
245256259273342
256264266281321
333352356389419
BSR 2014- Department of Buildings
S07- 459
BSR Rate
285296299316374
422452458506549
310323
BSR 2014- Department of Buildings
S07- 460
BSR Rate
326343
BSR 2014- Department of Buildings
S07- 461
BSR Rate
413
496535541601650
384403409432534
660717727812886
BSR 2014- Department of Buildings
S07- 462
BSR Rate
256268271286351
429464470526571
BSR 2014- Department of Buildings
S07- 463
BSR Rate
BSR 2014- Department of Buildings
S07- 464
BSR Rate
228237239251300
350376380422456
294310314333419
530578586660721
BSR 2014- Department of Buildings
S07- 465
BSR Rate
235246249263333
426464471533578
383391397425525
BSR 2014- Department of Buildings
S07- 466
BSR Rate
362386390420458
9651,0441,0631,1781,492
638691707759907
BSR 2014- Department of Buildings
S07- 467
BSR Rate
1,0371,1381,1521,2341,492
BSR 2014- Department of Buildings
S07- 468
BSR Rate
1,0621,1651,1781,2621,518
928947954998
1,053
869895899931971
BSR 2014- Department of Buildings
S07- 469
BSR Rate
487507514561615
615668687736962
448471478522644
BSR 2014- Department of Buildings
S07- 470
BSR Rate
466485489516638
460495501545671
728790801878
1,091
BSR 2014- Department of Buildings
S07- 471
BSR Rate
733798810890
1,097
BSR 2014- Department of Buildings
S07- 472
BSR Rate
748846860
1,0631,131
848904907
1,0111,232
837949964
1,0611,272
BSR 2014- Department of Buildings
S07- 473
BSR Rate
840939954
1,0421,284
677676686755920
695756767842
1,015
BSR 2014- Department of Buildings
S07- 474
BSR Rate
744777801883992
852907921
1,0161,167
882943
1,0371,0581,202
BSR 2014- Department of Buildings
S07- 475
BSR Rate
879938952
1,0511,209
880941
1,0291,0271,182
886953
1,0251,0491,204
BSR 2014- Department of Buildings
S07- 476
BSR Rate
364378383413518
456476482518659
515535541574715
446470478515678
341354358386488
403
BSR 2014- Department of Buildings
S07- 477
BSR Rate
422428462600
347365371402532
426449456491648
328341345372472
401419425458595
367384390419543
418439446480633
BSR 2014- Department of Buildings
S07- 478
BSR Rate
326338342368468
392411417449586
358374379408528
411432439473622
443475487522661
525562575
BSR 2014- Department of Buildings
S07- 479
BSR Rate
616787
557592602639798
481519530571749
393421430462586
446480490528685
386417427462608
456493503542711
BSR 2014- Department of Buildings
S07- 480
BSR Rate
371398406437555
435468477514665
403433442475614
445480489528692
364390397427544
422455463500649
392421429462
BSR 2014- Department of Buildings
S07- 481
BSR Rate
596
437471480518678
551594595659851
644694699766995
666711719774984
600650662719953
501540
BSR 2014- Department of Buildings
S07- 482
BSR Rate
544597773
567613622678891
494536545596794
578625638692917
479517523571742
556601611663872
511552560610800
BSR 2014- Department of Buildings
S07- 483
BSR Rate
566613625677897
472509515562730
543587598649855
500540548596781
558604616668884
648676686
BSR 2014- Department of Buildings
S07- 484
BSR Rate
741944
689717727788996
668690698742919
574597605655838
578602611657841
592615624677866
510531539582756
BSR 2014- Department of Buildings
S07- 485
BSR Rate
558580588637817
550572581624802
574596605655838
536556564606778
552573581629807
539561569611785
558580588637
BSR 2014- Department of Buildings
S07- 486
BSR Rate
817
530550559599770
547568576624800
BSR 2014- Department of Buildings
S07- 487
BSR Rate
675739760833
1,056
735806829906
1,166
695760781851
1,092
668710717768888
BSR 2014- Department of Buildings
S07- 488
BSR Rate
811822832897
1,085
1,0911,1691,1871,2971,550
1,3511,4601,4841,6301,992
BSR 2014- Department of Buildings
S07- 489
BSR Rate
1,4761,6001,6271,7922,208
653710722800897
515526529542579
BSR 2014- Department of Buildings
S07- 490
BSR Rate
575591596616673
598620626653728
579596600620671
BSR 2014- Department of Buildings
S07- 491
BSR Rate
19631635660714
578619626676810
686738748813985
BSR 2014- Department of Buildings
S07- 492
BSR Rate
855809820895
1,090
872926936
1,0021,144
828885897
BSR 2014- Department of Buildings
S07- 493
BSR Rate
9781,189
698751761827999
766829841918
1,042
767828839
BSR 2014- Department of Buildings
S07- 494
BSR Rate
9151,086
BSR 2014- Department of Buildings
S07- 495
BSR Rate
1,300
5,265
6,836
7,531
1,062
750
1,068
2,106
28,364
22,613
13,294
2,134
BSR 2014- Department of Buildings
S07- 496
BSR Rate
3,602
8,647
BSR 2014- Department of Buildings
S07- 497
BSR Rate
446
481
562
654
884
1,254
458
365
332
202
273
146
BSR 2014- Department of Buildings
S07- 498
BSR Rate
408
468
184
192
367
574
BSR 2014- Department of Buildings
S07- 499
BSR Rate
616
559
96
451
102
786
BSR 2014- Department of Buildings
S07- 500
BSR Rate
786
38,640
381405412448594
445482496535710
536
BSR 2014- Department of Buildings
S07- 501
BSR Rate
584588651873
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 194
A-DEMOLISHER
B-EXCAVATOR
C-CONCRETER
D-BRICKLAYER
E-MASON
F-PAVIOR
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 195
G-ROOFER
H-CARPENTER & JOINER
J-IRONMONGER
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 196
K-BRASS FOUNDER
L-PLASTERER
M-TINKER
N-GLAZER
P-PAINTER & DECORATOR
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 197
Q-PLUMBER
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 198
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 199
R-DRAIN LAYER
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 200
S-MISCELLANEOUS
T-ELECTRICAL INSTALLATIONS
U-ALUMINIUM FABRICATOR
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 201
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 202
Maintenance BSR for 2014
Department of Buildings, Sethsiripaya, Battaramulla.
INDEX
A-DEMOLISHERChipping lime plastering Roof removing Demolishing rubbleRemoving and stacking tilesRemoving water proof, asbestos ceiling &Valance or Barge boards.Chipping cement plasterTransporting debrisPreparatory workFelling Trees Removing Top Soil
B-EXCAVATORFilling Under floors & foundationsEarth work supports
C-CONCRETERConcreting Mass (Gr.15 Mix)Concreting Drains (Gr.15 Mix)Concrete (Grade 20 Mix)Curbs Concreting Drains, semi-circularConcreting Lintols (Gr. 20 Mix)Slabs over drainsConcreting of Beams and Columns (Gr. 20 Conc)Concreting Slabs (Gr. 20 Mix)Concreting Structural Elements (Gr. 25 Mix)Ready mixed ConcreteForm work (Untreated Non-structural Category A)Form work (Using Timber planks)Plywood form work (20mm thk.)
D-BRICKLAYERBrickwork in (1:5) cement mortar Brickwork Wire cut)Brickwork in (1:8) cement mortar
E-MASONRandom RubbleCellular (Hollow) block masonrySolid block masonryPaste rubble masonry
F-PAVIOR
Floors, gravel Floor tiles (Laying only)Tiles- pressed
Floor tiles- Porcelain glazed (Non homogeneous)Floor tiles- Vitreous Porcelain ( Homogenous)-LocalFloor tiles- Polished Porcelain ( Homogenous)-LocalFloor tiles- Rustic Type ( Homogenous)-LocalFloor tiles- (Approved quality)Terrazzo tile flooringTerracotta tilesWall tiles -glazed ( Approved Quality)
Floor tiles- Ceramic Non-skid ( Approved quality)Floor tiles- Ceramic glazed (Non homogenous)-Local
Wall tiles -Local
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 203
INDEX
Wall tiles (Fixing only)Border Tiles for Wall (Decorative)
Glass blockPVC carpeting Loop pile carpeting Cut pile carpeting Interlocking pavingPaving tile Slabs
G-ROOFERCorrugated sheetsCorrugated Aluminium sheetsCorrugated Asbestos SheetsCorrugated Asbestos "Colorup" SheetsZinc Aluminium Sheet RoofingCorrugated galvanized iron Sheet RoofingLeaks -on roofsRidgingZinc Aluminium ridge capping Skylight glassTiles, calicut pattern, flatTiles half round Structural Steel Purlins for RoofHigh tensile Galvanized steel, C-channel purlins for Roof Heat and Sound installation (Double side luminary Aluminium foil)Timber Members for Roofing
H-CARPENTER & JOINERBoards, barge, valance, fasciaCeiling / PartitionPartitionsTimber PlugsPlywood PanelsCove, mouldingsDoors or windowsDoor framePlywood Door Doors or windows framing and battening sashDoors glazing and/or paneling Door or Window frame Fillets, quadrant Timber GateLouver bladesWooden Posts Reepers, timber Roof with sawn timber framework & Covering Tiles on itShelvingSkirting Other Carpentry work. TrellisPantry cupboards units
J-IRONMONGERBolts and Nuts, IronIron BracketsWeld meshCabin HooksCasement StaysChimneyGate, Iron
Granite flooring-Local
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 204
INDEX
Gutter HooksHasp and stapleHinges (Iron)Hinges (Stainless Steel) for Timber DoorsHoldfastLocks (iron)Mild steel rodsWire mesh Reinforcement, with Tor steel rodsChain-link fencingMild Steel Grill work Guard rails ( Heavy duty GI-Pipe)Hand rails ( Heavy duty GI-Pipe) Hand rails (Stainless Steel, 1.5mm thick Pipe- Grade 304 )Web Truss
K-BRASS FOUNDERBolts, barrel, brassCabin Hooks (Brass)Casement fasteners, brassHasp and staple, brassHinges, brassLocks (Brass)
L-PLASTERER
MouldingRendering CementCement floating coat.Cement Rendering and smooth Coloured floating coatRendering Cement with PudloSkirting in cement mortarD.P.C- 3/4"
M-TINKERGI-Down pipes / Hold fastsG.I FlashingZn/Al-FlashingG.I semicircular GuttersValley gutter (G.I)Zinc Aluminium Colour bonded valley gutter (0.47mm) Zn/Alu high tensile down pipes Zn/Alu gutters Zn/Alu Down pipe Bends
N-GLAZER
P-PAINTER & DECORATOR
Skim coatCement washing to wallsWhite or colour washing wallsSnowcem paintAcrylic wall Filler ( Primer for Interior)Alkali resisting primerElastometic filler PrimerAlkali resisting water Proofing sealerHeat Resistant paintSilicone masonry water repellent paint
Plastering (walls) Plastering (beams, slab soffits)
Plastering (Reveals)
Surface preparation (Old work) for Painting (Scraping /Patching /Smoothing)
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 205
INDEX
Bathroom paintEmulsion paint (Interior)Painting General Purpose weather shied ( Exterior)Painting on old work with General Purpose weather shied (Exterior paint)Painting on New work with, Two Coats of Acrylic Emulsion weather shied Acrylic Emulsion (Exterior paint)Painting asbestos sheet roofFloor PaintingAnticorrosive paintPainting on GI SurfaceAluminium paintEnamel paintRemoval of Paint from timber. Wood preservative Enamel paint with Wood primer Under coatPolishing wood work with WaxPainting with Wood sheenPolyurethane Varnishing polyurethane varnish-MattRemoving VarnishPainting with Sanding sealer / Woof finish LacquerPainting with Perque varnishPainting Letters on (Board / Wall)
Q-PLUMBERBall valve-UPVCBall valve-BrassConcealed Taps/Valves-Chromium platedFlush valveFlush valve to existing Urinal (Imported )Gate valve brass imported (English or equivalent, approved quality).Float valueFoot value Lavatory BasinRemoving bath room FittingsCloset-pedestal typePlastic seat cover, imported
Close coupled water closet suite (colour) Close coupled European type low level commode suit (white ) Bidet, pedestal type-ImportedBidet, pedestal type, Manufactured in Sri Lanka.Bath wear set (3-Pieces)-Fixing OnlyCloset-squatting typeRemoving Closet-squatting typeFixing available Closet-squatting typeSquatting pan- EuropeanSquatting pan Ceramic ( Indian)Closet squatting type ( Indian or equivalent)Cistern high level (Plastic)- ( Indian or equivalent)Cistern high level, ceramic-(Twyford or equivalent approved quality)Cistern, high level, auto flush-CeramicCistern, high level, auto flush-PlasticCistern low level, flushing- porcelain (Indian , approved quality).Syphon Magic Bend Urinal(Indian)
Close coupled water closet suite (white) -ImportedClose coupled water closet suite (white)-Manufactured in Sri Lanka.
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 206
INDEX
Urinal Imported- TwyfordSink and fittings-Fixing OnlySinkReplacing SinkStainless steel kitchen sinkWash Basin Wash Basin (local Bath wear)Corner wash basin (Imported quality)Corner wash basin (Indian, approved quality)Vanity basinRubber plugsWooden plugsBottle traps PVC P-Trap (2" dia.) Fixing and Repairing , available TapsBib Taps (Metallic)Bib Taps (Plastic)Swan-Neck tap-(Metallic)Swan-Neck tap-(Plastic)Chromium plated angle Taps/Valves 1/2"Angle Taps/Valves (Plastic)Chromium plated basin tap 1/2"Push tapsStop tap. (Imported approved quality)Stop Taps (Plastic)Bath tub tapGarden Taps (brass)Garden Taps (Plastic)Pillar cocksPillar tapsBasin Piller Taps (Plastic)Stop cockConnector, G.IElbow, G.IHooks for pipesJam NutsNipples, G.IPipes G.I Socket G.I R.S.J 's as supports for tanksRemoving tank G.I Fixing tank, G.IClearing & washing tankPlastishell (Single Layer) water tank Plastishell (Triple Layer) water tank Floater switchTeesTrapsBath room accessories (Total Set) Tumbler holderSoap tray/dishSoap dispenserShelves, plate glass Towel rail Paper holder SEVATooth brush holder
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 207
INDEX
Robe hook (SEVA)Bath room mirror,Shower rose-Fixing OnlyShower rosePlastic Jet Shower roseShower headBidet spray importedAccessoriesFixing bends, elbows and tees- Workmanship onlyBends P.V.CElbows P.V.CReducing sockets & Tees P.V.CReducing Tees P.V.CRepair Sockets & Tees P.V.CValve Socket P.V.CFaucet Socket P.V.CTapered union without thread P.V.C Equal tees-P.V.CPlugs, sockets-P.V.CPipes P.V.CFixing pipesPipes P.V.C (25% pipe cost included for Specials)Flexible cord (S--Lon or Equivalent))Flexible cord (Imported European)Flexible hoseGarden Watering Hose ½" dia.Water pumpElectric water geyserPlastic gullyShower tray fiberglassElbows for down pipe. Running head. Gutter end.Gutter Joint.Eves gutters (PVC)-Square typeDown pipes 3½" dia. P.V.C
R-DRAIN LAYERInterceptor, EarthenwareManhole- brick in cement
Manhole cover, reinforced concreteManhole cover, Cast IronCast iron gratingWire dome (Steel)Wire dome (Copper)Drainage Fittings 4" (110mm) dia-(Local make)Drainage Fittings 2" (63mm) dia.Drainage Fittings 1½"or (50mm) diaPipes P.V.C, 4"(110mm) dia, (type 250)-(Vent pipes fixed to walls)Pipes P.V.C, 4"(110mm)dia, (type 400)-(Vent pipes fixed to walls)Pipes P.V.C, 4"(110mm) dia, (type 400)- lay in TrenchesDrain Pipes P.V.C, 4" dia, (type 600)- lay in TrenchesDrain Pipes P.V.C, 6" dia, (type 600)- lay in TrenchesDrain Pipes P.V.C, 12" dia, (type 600)
RCC Manhole (Type A)- [As per Drg.No 2013-TP-ST06 & ST07]RCC Manhole (Type B)- [As per Drg.No 2013-TP-ST06]RCC Manhole (Type C)- [As per Drg.No 2013-TP-ST06]
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 208
INDEX
S-MISCELLANEOUS Scaffolding of BamboosSteel scaffolding SetsGarden lampFencingWell, bailing out waterWater proofing (Treatment)Water proofing (Membrane)Timber treatmentDoor PVCLandscapingLaying turf sodsPalm treesMixed FlowerRoad ConstructionProviding Labour Services Flagging
T-ELECTRICAL INSTALLATIONSIn PVC conduitIn PVC conduitIn PVC CasingIn PVC CasingDistribution BoardsCabling in conduitsCabling in PVC CasingEarth Electrode Luminaries and FixturesSwitch socket outletReplacing sunk switchFansExhaust FansWall FansFluorescent LampConduit PipePVC CasingCommissioning Wires Commissioning Earth Wires Supply & Installation of Dol Starter
U-ALUMINIUM FABRICATORBoards and Glass PansTypical Aluminium LouversAluminium SUN Louvers with Louver Frame (Alumex ALU 180 or equivalent)
Single Row Aluminium Partition Frame Work with Boards/GlassSingle Row Aluminium Partition Frame Work with Louvers2 Row Aluminium Partition Frame Work with Boards/Glass2 Row Aluminium Partition Frame Work with Louvers & Boards/Glass3 Row Aluminium Partitions 3 Panel Aluminium Louver Partitions Aluminium 76mm Shopfront Aluminium 100mm Shopfront Aluminium Curtain Wall (2.0mm thick)Aluminium Curtain Wall (1.5mm thick)Aluminium doors
Aluminium SUN Louvers (Alumex ALU 180 or equivalent) with BIRD'S MOUTH BRACKETS (Alumex ALU 282 or equivalent)
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 209
INDEX
Door Outer frames Aluminium Sliding DoorsAluminium Casement WindowsCasement Window Frames Only Aluminium Casement & Pivot Window (Frame Only)Casement Window Sash Only Aluminium Sliding windowsAluminium composite claddingDoor lock for Aluminium Doors Sliding lock for Aluminium doorHinges (Stainless Steel) for Aluminium DoorsHot dip GI interlocking ceiling frame work only(Mineral fiber / Stone wool) acoustic ceiling suspended ceiling Mineral fiber acoustic Suspended ceilingSuper Flex Suspended ceilingGypsum board suspended ceilingMetal ceilingPartitioning (Gypsum board)Aluminium, Ceiling panels (Pinholes)Aluminium, partitions with available extrusions Roller Shutter door, AluminiumRoller door, Aluminium, Zn/Alu Aluminium Fixed Glass Windows
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 210
Item Start From
S07-25A026A029A032A035A038A043A044A046A047A051
S07-28B016B019
S07-30C001C007C009C014C015C016C024C028C034C036C043C046C049C051
S07-33D002D010D028
S07-35E001E004E007E010
S07-36
F007F008F012F013F015F018F022F025F028F030F035F037F038F047
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 211
Item Start From
F053F055F059F062F063F066F067F069F071
S07-41G001G002G005G008G009G010G013G019G027G029G030G040G049G053G055G056
S07-45H007H012H026H033H034H035H037H067H069H073H076H080H082H084H089H092H095H100H104H107H109H116H125
S07-53J001J013J014J017J022J024J032
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 212
Item Start From
J033J034J037J053J055J057J066J075J079J081J085J086J086J088J089
S07-59K002K011K018K023K026K039
S07-62L001L004L009L017L025L028L029L030L032L033
S07-64M001M008M010M011M031M032M034M036M038S07-66
S07-67P003P007P008P011P017P020P021P022P023P024P025
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 213
Item Start From
P026P027P031P033P035P037P038P042P046P048P049P052P054P056P058P060P061P063P066P068P069P072P074
S07-72Q001Q006Q012Q015Q018Q020Q037Q043Q052Q058Q070Q074Q075Q077Q087Q088Q089Q090Q092Q093Q094Q095Q098Q100Q101Q102Q103Q104Q105Q106Q107Q109Q110
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 214
Item Start From
Q112Q120Q121Q125Q127Q131Q134Q143Q144Q146Q148Q150Q151Q156Q157Q161Q165Q171Q172Q174Q176Q178Q179Q181Q182Q188Q189Q190Q192Q194Q196Q197Q204Q215Q231Q237Q244Q251Q276Q290Q291Q293Q295Q298Q302Q307Q308Q314Q319Q320Q321Q324Q325Q326Q328Q329
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 215
Item Start From
Q331Q332Q335Q336Q340Q342Q343Q345Q347Q348Q355Q362Q368Q375Q382Q389Q396Q410Q417Q437Q438Q443Q449Q454Q456Q457Q459Q463Q469Q471Q472Q473Q474Q475Q476Q478
S07-98R001R004R007R011R015R019R020R022R023R025R027R039R049R059R060R061R064R067R070
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 216
Item Start From
S07-102S006S008S010S011S027S031S033S034S035S038
S046S052S058S068S072
S07-106T001T007T010T016T019T044T074T088T089T109T112T122T123T127T128T132T138T147T155T159
S07-113U001U017U042U047
U052U062U067U082U097U137U177U182U187U192U197
BSR 2014- Department of Buildings1
Esti Rana / BSR 2014 S0 7 - 217
Item Start From
U207U242U312
U632U647U677U742U743U748U753U765U766U767U770U772U773U775U777U778U779U780U782
Rate per sq.ft76mm extrusions 100mm extrusions
Al. Partitions MF NA BA PC WF MF NA BA PC WF
Fully board (2 row) 7 ft height 597 605 608 622 664 N/A N/A N/A N/A N/A
Glass & board (2 row) 7 ft height 491 502 505 520 583 N/A N/A N/A N/A N/A
Fully board (3 row) 10 ft height 610 618 620 635 675 687 706 710 743 773
Board, glass & board (3 row) 10 ft height 546 557 560 577 635 683 713 719 767 810
781 835 846 913 1126 954 1031 1045 1153 1346
Swing Doors (Excluding lock, door closer)76mm 100mm - 1.6mm tk
MF NA BA PC WF MF NA BA PC WF
1673 1792 1811 1933 2233 2030 2149 2167 2287 2587
1693 1812 1831 1953 2253 2050 2168 2187 2307 2607
1516 1628 1645 1751 2034 1730 1842 1858 1964 2246
1535 1648 1664 1771 2053 1749 1862 1878 1983 2266
window41mm 60mm
MF NA BA PC WF MF NA BA PC WFTwine sash fully glass casement window 1160 1215 1226 1305 1527 1212 1282 1298 1381 1625Fixed glass window 532 556 563 599 745 596 633 647 686 861Fixed louvered window 1617 1780 1815 2023 2661 1681 1857 1899 2110 2777
100mmMF NA BA PC WF
899 997 1011 1214 1282
80mmMF NA BA PC WF
Board, glass & "y" type louver (3 row) 10 ft height
Single sash swing door with top glass & bottom fabric
Single sash swing door with top glass & bottom both side coloured cladding board
Double sash swing door with top glass & bottom fabric
Double sash swing door with top glass & bottom both side coloured cladding board
100mm double sash Sliding Door (One sash fixes) fully glass excluding lock, handles
80mm double sash sliding window (both sash sliding) fully glass
837 889 899 964 1136
80mm double sash sliding window (both sash sliding) fully glass
70mm (1.2mm thick)MF NA BA PC WF1320 1401 1412 1516 1812
687 735 739 802 10241772 1959 1991 2226 2940
Top Related