Best Practices for Constructing Concrete Pavements
LTRC Concrete Pavements Seminar
Baton Rouge, Louisiana
October 28, 2009
Dr. Michael AyersDirector of EducationDirector of Education
Learning Objectives
Recognize the relationship between design assumptions and construction operationsand construction operations.Develop a checklist of all critical construction elements and corresponding responsibilitiesand corresponding responsibilities.Recognize the most typical construction–related problems and how to avoid themproblems and how to avoid them.Determine which construction operations have the most influence on ride quality, slab uniformity, premature influence on ride quality, slab uniformity, premature cracking and other important factors.
How Do You Define Quality?
Depending on your perspective (contractor, p g y p p (owner, user) the following may define quality issues:
Inexpensive to build and maintain.Safe, smooth, quiet, environmentally friendly., , q , y yConstructible.Others?Others?
Quality Construction Practices
Concrete pavements play a primary role in satisfying public demands for better roads.The best design will fail prematurely if construction is not of adequate quality.The number 1 goal in construction is:
Build it equal to or better than called for in the qdesign and specifications!!!
Cycle of Quality
InnovationsChallenges InnovationsChallenges
SolutionsSolutions
Challenges
Design and construct concrete pavements with the following characteristics:
Long-lasting (minimal maintenance and rehabilitation).Reasonable initial cost.Rapid construction (minimal delays to public).SmoothSmooth.Safe.Quiet.Quiet.Cost effective.Environmentally “friendly.”
Innovations
Innovations generally fall into one or more of the g yfollowing categories:
Design (AASHTO Interim Mechanistic-Empirical g ( pPavement Design Guide (M-E PDG)). Materials.Equipment.Processes.
Solutions
The means to construct high performance, long g p glife concrete pavements exists todayA coordinated effort is required to achieve this A coordinated effort is required to achieve this goal including designers, specification writers, materials producers, contractors, and many materials producers, contractors, and many others
Relationship Between Pavement Design and Constructiong
Objectives of Pavement Design
To provide a surface that is:Strong (structural)Smooth (ride)( )Safe (friction and drainage)EconomicalEconomical
Initial construction costRecurring maintenance cost
AASHTO Pavement Design Guide
Empirical methodology based on AASHO Road Test in the late 1950’1950’sSeveral versions:
1961 (I t i G id ) 1972 1961 (Interim Guide), 1972, 1986, 1993 (Empirical)1986 Guide highlights need 1986 Guide highlights need for M-E design1998 Rigid Supplemental g ppGuide (based on M-E concepts)
Current AASHTO vs. Current Needs
50+ million loadsWide range of structural and
rehabilitation designs
1 1 illi l d
AASHO Road Test1.1 million load repsLimited structural sections
AASHTO Design Guide1 climate/2 years 1 set of materials
All climates over 20 50 years
1 set of materials
All climates over 20-50 years New and diverse materials
M-E Design
Mechanistically calculate critical pavement response (i t t i d d fl ti ) d t(i.e., stresses, strains, and deflections) due to:
Traffic loadingE i t l ditiEnvironmental conditions
Accumulate damage over timeEmpirically relate damage over time to pavement distresses through calibrated distress models, e.g.:
C ki F l i R h i JPCPCracking, Faulting, Roughness in JPCPPunchouts, Crack Width, Roughness in CRCP
Climate
MaterialsStructure Traffic
Inputs
Analysis Process
Outputs
Dam
age
Dis
tres
s
Field DistressMechanistic Response
Damage AccumulationTime
D
DamageDistress Prediction and
ReliabilityResponse Reliability
Current and Future Construction Requirements Controlled by Requirements Controlled by Design?
The M-E PDG has many construction–related variables including the following:
C t t th d if itConcrete strength and uniformity.Coefficient of thermal expansion of the concrete.Curing type and effectiveness (curling and warping)Curing type and effectiveness (curling and warping).Joint spacing.Load transfer.Subbase type and overall support conditions.Others.
Inputs
Site-related inputs (these cannot be altered economically)economically)
Traffic—ESALs or load spectraSubgrade engineering properties strength Subgrade—engineering properties, strength, modulusClimate—precipitation temperatureClimate—precipitation, temperature
Design-related inputs (the designer has control over these properties)these properties)
Structural section—thicknesses, layer typesPaving materials—strength modulusPaving materials—strength, modulus
Concrete Strength, Cracking
Concrete MR Effects on Transverse Cracking
708090
100
erce
nt) Chicago, 50% reliability,
550 psiChicago 95% reliabilty
40506070
d Sl
abs
(pe Chicago, 95% reliabilty,
550 psiChicago, 50% reliability,650 psiChicago 95% reliability
0102030
Cra
cke Chicago, 95% reliability,
650 psiChicago, 50% reliability,750 psiChi 95% li bilit0
7 8 9 10 11 12 13
Slab Thickness (inches)
Chicago, 95% reliability,750 psi
Base Type, Cracking
Effect of Base Type on Estimated Transverse Cracking
708090
100
erce
nt)
Chicago, 50% reliability,granular base
40506070
d Sl
abs
(pe g
Chicago, 95% reliability,granular baseChicago, 50% reliability, 4inch CTB
0102030
Cra
cke c C
Chicago, 95% reliability, 4inch CTB
07 8 9 10 11 12 13
Slab Thickness (inches)
Climatic Effects, Cracking
Climatic Effects on Estimated Transverse Cracking
708090
100
erce
nt)
40506070
d Sl
abs
(pe Chicago, 50% reliability
Chicago, 95% reliabilityPhoenix, 50% reliabilityPhoenix 95% reliability
0102030
Cra
cke Phoenix, 95% reliability
07 8 9 10 11 12 13
Slab Thickness (inches)
What Isn’t Covered in Design?
Probably the single most important aspect of long-term pavement performance isn’t even listed as a design input.
Concrete Durability
How can we address durability and what needs to be measured?
Specifications
Specifications
Specifications are used to control critical elements of projects.All specifications act to assign risk.
Method specifications assign risk to the owner.End result specifications assign risk to the contractor.
Alternative types of specifications are being used on an ever increasing number of projects:
Performance based specifications, design/build, warranties and others
Concrete Materials and Mix ConsiderationsConsiderations
Concrete Materials
Don’t forget about chemical admixtures and SCM’s
Concrete Properties
The key construction element is UNIFORMITY.For most projects, uniformity can only be controlled at the time of batching.The following factors are the most important:
Workability (slump is NOT a very good indicator).Setting time and rate of strength gain.28-day strength (or what the specification requires).
Typical Cement Composition
Phases Amount, % Property
C3S 50 – 55 Early strength Heat
C2S 20 – 25 Later strengthC2S 20 25 Later strength
C3A 5 – 12 Heat Sulfate resistance
C4AF ~ 8 Color
CSH 5Setting Strength/shrinkageCSH2 ~ 5 Strength/shrinkageAdmixture performance
Chemical Admixtures
The most typical admixture types for paving yp yp p gapplications are listed below. Changing the concrete mix and components may change requirements .
Air entraining admixtures (AEA).
Water reducers.
S t dif i d i tSet-modifying admixtures.
Aggregates
Aggregates comprise the majority of the volume f t iof a concrete mix.
Aggregate properties have a strong influence on the following concrete properties:
Durability.Workability.Strength.gDimensional changes in concrete.Many others.a y o e s
Aggregates in Concrete
The physical properties of aggregates (natural or manufactured) have a strong effect on the properties of fresh and hardened concrete:
Gradation.Surface texture.P ti l hParticle shape.Absorption.DurabilityDurability.
Aggregate Gradation (cont.)
The maximum aggregate size used for paving is usually 1½ inches or less.Well-graded aggregates are desirable:
Maximize aggregate packing.Minimize cement content (economical).More workable.Less drying shrinkage.
Aggregate Gradation (cont.)
Combined grading is used to obtain the maximum g gaggregate density with the materials at hand.Combined grading may use 2 or more aggregate Combined grading may use 2 or more aggregate stockpiles (bins)Overall material specifications generally represent Overall material specifications generally represent the total or combined grading, although individual aggregate specifications may applyaggregate specifications may apply.
Shilstone Coarseness Chart
Field Testing Plan
The 3 categories of testing include:g gPrior to production.Mix design evaluation.gMixer uniformity test.
These procedures are suggested when a new mix These procedures are suggested when a new mix is being evaluated, regardless of project size.
Adjusting Properties
Subject to the results of the trial batches, adjustments to the mix are likelyThe most typical mix proportion adjustments include:
WorkabilityStiffening/settingBl diBleedingAir void systemUnit weightUnit weightOthers
Final Thoughts on Materials
The stockpiles at either the ready mix plant or the p y pbatch plant need to be constantly checked. If the project requires the Contractor to provide the QC, p j q pthen the control charts should be maintained continuously. yAdmixtures – check the compatibility with the cement, fly ash or slag.cement, fly ash or slag.
Subgrades and Subbases
Subgrades and Subbases
Roadbed (subgrade and subbase) design is key ( g ) g yto long-term performance and smoothness of concrete pavements.p
TerminologyTerminologyDesign PrinciplesSubgradesSubgradesSubbases
Terminology
A concrete pavement structure typically consists of a concrete surface and subbase(s) placed upon a prepared subgrade.A “base” is part of an asphalt pavementstructure, while a subbase is an optional element f t t t tof a concrete pavement structure.
Terminology
Why the difference in terminology?y gyPressures imposed on a base (under asphalt) are dramatically different than those imposed on a subbase (under concrete) due to differences in moduli (stiffness) of the surface layer.Material requirements for a subbase may be relaxed when compared to a base.
Design Principles
Roadbeds for a concrete pavement structure should:Be free from abrupt changes in character of the materials (should be uniform and constructed of a material that will provide requisite stability over the life of the pavement)provide requisite stability over the life of the pavement)Resist erosionBe engineered to control subgrade soil expansion and frost g g pheave.
Above all other design concerns, uniformity is of utmost importance.
Design Principles
Because of the rigid nature of concrete pavements, loads are distributed over relatively large areas relatively large areas, greatly reducing stresses on the subgrade/subbase; on the subgrade/subbase; thus, concrete pavements do not necessarily require y qexceptionally strong foundation support.
Design Principles
Subgrade/subbase design is engineering:g g g gThe pavement design engineer should consider all subgrade/subbase types (stabilized or unstabilized) and available materials (recycled or virgin) for each pavement design; there is no standard recommended
b d / bb bi ti f t subgrade/subbase combination for any concrete pavement.
S b d / bb l ti / i i i Subgrade/subbase selection/engineering is the designer’s option!
Subgrades
Means to control wet soils:E h t i i i t b Enhancement – removing excessive moisture by providing drainage via trenches or toe drain; compacting the subgrade using heavy equipment; or compacting the subgrade using heavy equipment; or adjusting the moisture content through chemical modificationReinforcement/Separation – removing excessive moisture by using a geosyntheticSubstitution removing excessive soils and replacing Substitution – removing excessive soils and replacing with select borrow material or, alternatively, covering up excessive soils with a suitable materialp
Subbases
Concrete pavement design thickness is relatively insensitive to support stiffness (modulus of subgrade reaction), so it is improper engineering to make a subgrade/subbase stronger or thicker in an attempt to subgrade/subbase stronger or thicker in an attempt to decrease concrete pavement thickness…
Subbases
Pumping of concrete pavementsp g p
Subbases
For pumping of a subbase to occur, several conditions t i tmust exist:
The pavement must have undoweled joints or joints with poor load transferWater must be presentThe roadway must have fast moving, heavy loads Th b d b fi i d i l h bb The subgrade must be a fine-grained material or the subbase must be an erodible material
Eliminating one or more of these casual factors should Eliminating one or more of these casual factors should mitigate pumping.
Subbases
Do you need a subbase?Pavements that are expected to carry 200 trucks or fewer per day (or less than 1,000,000 18-kip (80 kN) ESAL’s over the course of the service life of the pavement) do not typically require a subbase to prevent pumping.A subgrade soil that is naturally free draining typically will not pump.pump.Subgrade soils with less than 45% passing a No. 200 (75 μm) sieve and with a PI of 6 or less are adequate for moderate volumes of heavy truck traffic without the use of a subbase volumes of heavy truck traffic without the use of a subbase layer.
Subbases
Subbase Types:Unstabilized (granular) - 4 in. (100 mm) min. thickness Stabilized
Cement-StabilizedCement-Treated (CTB) - 4 in. (100 mm) min. thicknessLean Concrete (LCB) - 4 in. (100 mm) min. thickness( ) ( )
Asphalt-Stabilized (ATB) - 2 in. (50 mm) min. thicknessWith any subbase type, it is possible to utilize waste material (i.e., recycled concrete) as aggregate.
Subbases
Regardless of subbase type, the best results are obtained by:obtained by:
Selecting materials that prevent pumpingSelecting materials that will not contribute to excessive Selecting materials that will not contribute to excessive deflections and will remain stable over timeTreating the subbase surface (if necessary) to prevent bond to the concrete pavementSpecifying material gradation that will ensure a reasonably consistent (and uniform) subbase across an individual projectconsistent (and uniform) subbase across an individual projectBuilding the subbase to grade controls that foster a consistent concrete pavement thickness and smoothness
Unstabilized Subbases
Unstabilized subbases must have:A 4 in (100 mm) min thickness A 4 in. (100 mm) min. thickness A maximum particle size of no more than 1/3 the subbase thicknessLess than 15 percent passing the No. 200 (75 μm) sieveAn in-place density of 95 percent according to AASHTO T99An in place density of 95 percent according to AASHTO T99A Plasticity Index (PI) of 6 or lessA Liquid Limit (LL) of 25 or lessA L.A. abrasion resistance of 50% or lessA grade tolerance of ± ½ in. (± 12 mm) by a 10 ft (3 m) straightedgeA target permeability of about 150 ft/day (45 m/day), but no more than 350 ft/day (107 m/day) in laboratory tests (free-draining, NOT PERMEABLE)
Of th li iti th t f fi i th N 200 (75 ) Of these, limiting the percent of fines passing the No. 200 (75 μm) sieve is of utmost importance to creating a long-lasting unstabilized subbase that will prevent pumping.
Unstabilized Subbases
Typical job control tolerances from the target gradation for unstabilized subbases are:
±10% for materials 1 in. (25 mm) and larger.±8% for materials between 1 in. and No. 4 (25 mm and 4.75 mm).±5% for materials No 4 (4 75 mm) and smaller±5% for materials No. 4 (4.75 mm) and smaller.
The finished tolerance of the unstabilized subbase should be ±1/2 in (± 12 mm) of the design profile should be ±1/2 in. (± 12 mm) of the design profile grade.
Unstabilized Subbases
Be sure to consolidate to spec!p
Unstabilized Subbases
And at the proper thickness!p p
Stabilized Subbases
Stabilized subbases generally refer to subbase materials that are bound by either cement or asphalt.The higher degree of support offered by a stabilized subbase will not alter the required concrete pavement slab thickness appreciably, but it will add pumping resistance and increase the overall strength of the resistance and increase the overall strength of the pavement structure, spreading loads over larger areas and reducing strains.and reducing strains.
Stabilized Subbases
Stabilized Subbases
Although increased foundation stiffness via increased strength is beneficial from an beneficial from an applied loads point-of-view it could potentially view, it could potentially have a negative impact on environmentally o e o e ta yinduced stresses and strains.
Stabilized Subbases
On a cement-treated subbase, the loss of support occurs at a much slower rate. In this study it stabilized around one-half million load applications; even after 1 million loads joint effectiveness remains at a level of million loads, joint effectiveness remains at a level of almost 80 percent.
Stabilized Subbases
Other benefits of stabilized subbases:An excellent, stable all-weather construction platformBound subbase surfaces drain water quicklyAid in improving the final pavement smoothnessMinimize post-construction subbase consolidationMinimize intrusion of hard granular particles into the bottom of pavement jointsProvide an erosion resistant subbase Permit greater use of local materials
Alternative Subbase Materials
Recycled concrete and other alternative subbase materials should be considered for inclusion in a subbase for their positive economic and environmental benefits as well as resource conservationbenefits, as well as resource conservation.Benefits of using alternative subbase materials:
P fPerformanceEconomicsResource conservationResource conservationEnvironmental considerations
Permeable Subbases
Permeable subbases (subbases with a permeability of 350 ft/day (107 m/day) or greater in laboratory tests) have had a problematic (107 m/day) or greater in laboratory tests) have had a problematic history in the field. The reasons include:
Instability as a construction platformLoss of support caused from aggregate breakdownEarly age cracking caused from penetration of concrete mortar into the subbase voids during pavingIntrusion of fines from underlying layers into the permeable subbase voidsLoss of support caused from infiltration of the subgrade into the subbase Cost effectivenessVarious other overall field performance problems
Permeable Subbases
Cost effectiveness:
Permeable Subbases
Thus, permeable subbases are no longer p grecommended for concrete pavement structures. Free-draining subbases (subbases with a Free draining subbases (subbases with a permeability between 50 and 150 ft/day (15 and 46 m/day) in laboratory tests) and daylighted 46 m/day) in laboratory tests) and daylighted subbases are a reasonable alternatives to rapidly draining permeable subbases.draining permeable subbases.
Construction OperationsConstruction Operations
Pre-Construction Meeting
Provide the owner with the required information, Names & contact information for key project and emergency personnel. Erosion and environmental control plan Erosion and environmental control plan. Proposed schedule.Materials & subcontractor list. Quality control plan.
Propose any traffic control plans.Confirm the owners expectations – materials, specifications and quality.
Factors Influencing Quality
Equipment selection and set-up.Grade control (stringline or form setting Grade control (stringline or form setting operations).Subgrade and subbase preparationSubgrade and subbase preparation.Concrete production and delivery.Slipform paver or fixed form equipment operation.S p o pa e o ed o equ p e t ope at oDowel bar and tie bar placement.Finishing and texturing.g gCuring. Sawing operations.
Equipment Selection
Equipment selection is typically at the contractor’s discretion.The selection will be based on what is available, project size and location, specifications governing the project and so on.Th lit f th j b d d ll th i t The quality of the job depends equally on the equipment selected and the skill level of the crew.
Slipform Equipment Setup
Prior to paving, the contractor must check that the paver and all other elements of the paving train are working and all other elements of the paving train are working correctly . Setup is specific to a particular manufacturer and model.General paver considerations (abbrieviated list):
String line the pan.Check the side-forms depth keyways cleanlinessCheck the side-forms, depth, keyways, cleanliness.Check the vibrators.Check the width of the pan.Check the over build Check the over-build. Check if the kit is tight.Check the sensors are working and are set at the correct sensitivity.Check the tie bar spacing is correct on the placerCheck the tie-bar spacing is correct on the placer.
Grade Control - Stringline
•Set stringline to the Set stringline to the proper elevation based on survey hubs.•Use suitable material.•Maintain stringline.Use 2 stringlines•Use 2 stringlines.
•Common set-up preferredpreferred.•Check, check, and check again!!!g
Grade Control - Forms
There are many options available in setting formsavailable in setting formsThe overriding considerations are:
Match the form type to •Match the form type to the placing equipment.•Follow the established line and grade.•Place the form on a firm foundation.foundation.•Align the forms properly.
Grade Preparation
Grade trimming.
Concrete Production
Concrete paving projects can utilize both p g p jstationary plants and transit mixers, sometimes a combination.Plqnt production must match the requirements of the job.the job.Siting of the plant, environmental regulations, set-up calibration and maintenance are all critical up, calibration and maintenance are all critical factors.
Concrete Delivery
Delivery must be matched to the job type and y j yplocationThe paver is the determining factor in the volume The paver is the determining factor in the volume of concrete required and therefore generally controls the method of deliverycontrols the method of delivery
Equipment Operation
Regardless of the type of equipment used, the g yp q ppaving machine should be operated in a consistent manner.
Properly calibrated sensor system (if so equiped).Controlled and uniform speed.pLimited starting and stopping (preferably none).Consistent consolidation.Consistent consolidation.
Paver Sensor System
• Check thoroughly for proper operationg y p p p• Set wands level and plumb• Set counterbalance• Set counterbalance
Consolidation
The internal vibrators on the paver fluidize the concrete for extrusion.Adequate consolidation:
Required around dowels and ti b tie bars. Throughout the slab.
Internal Vibration of PCC
Good Consolidation Poor Consolidation
Consolidation
Vibrator Monitors
Set Ahead Steel Placement -DowelsDowels
Dowels on Baskets.
Forces on Dowel Basket Assembly
Anchoring the Dowel Basket
Anchoring the Dowel Basket
Dowel Bar Placement with DBI
Tie Bar Insertion
Finishing and Texturing Operations
Finishing Operations
Finishing does not generally mean hand finishing g g y gin the traditional sense“Closes” the surface of the concreteCloses the surface of the concreteMechanized or hand work depending on specific operationoperationStraight edging to remove high spots following pa erpaver
Finishing Operations
Finishing Operations
Finishing Operations
Why Do We Texture
Safety!!!!yVehicle Control (Lateral Stability)Safe Stopping Distancespp g
Remove Water from the PavementProvide Benefits During Inclement WeatherProvide Benefits During Inclement WeatherImprove Micro and Macro TextureNoise Control
Texturing
Texturing options:g pDrag texturesLongitudinal tiningLongitudinal tiningTransverse tiningDiamond grindingDiamond grindingInnovative techniques
You Can Hand Texture
Resulting Texture From Diamond GrindingGrinding
Curing
Curing Concrete
TemperatureCuring includes the following:
TimeMoistureMoisture
If f th f t If any of these factors are neglected, the desired
ti ill t d lproperties will not develop
Effect of Adequate Curing on Hardened Concrete
Adequate curing results in the following:
Hardened Concrete
Adequate curing results in the following:Higher strengthIncreased watertightness (decreased permeability)Better abrasion resistanceIncreased freeze-thaw resistanceIncreased freeze thaw resistanceBetter volume stability
Effect of Moist Curing
Effect of Curing Temperature on StrengthStrength
Curing to Maintain Moisture
Maintain moisture in concrete:To facilitate hydration To prevent surface (map) crackingp ( p) gTo allow the PCC to reach its designstrengthstrengthOthers
Curing Methods
Supply additional water:Supply additional water:Ponding or immersionSpraying or foggingSaturated wet coveringsg
Curing of Concrete by Supplying External Water
Evaporation from water surface
Water supplied from external source
Saturated
Concrete
Curing Methods (cont.)
SSeal in mixing water:Plastic sheetsMembrane-forming curing compoundscuring compounds
Membrane Curing of Concrete
Evaporation from water surface
Curing membranePartially saturated
Saturated
Concrete
Is This Adequate Curing?????
J i ti d S i O tiJointing and Sawing Operations
Why Joint Concrete Pavement?
Control natural cracking caused by internal g yslab stresses.
Stresses from:Chemical shrinkageTemperature gradient (curling)Moisture loss (drying shrinkage/warping [relative humidity gradient])Restraint to contraction (subbase friction/bond)Restraint to contraction (subbase friction/bond)
Why Joint Concrete Pavement?
Control natural transverse & longitudinal cracking g gfrom internal slab stresses.
40 80 ft 15 20 ft40-80 ft 15-20 ft
Why Joint Concrete Pavement?
Other reasons we joint concrete pavements:j pDivide pavement into construction lanes or incrementsincrements.Delineate lanes for drivers.Accommodate slab movements.Provide load transfer via placed dowelsplaced dowels.Provide uniform sealant reservoir.
Types of Joints
Joint types:ypContractionConstructionIsolation (and, if necessary, expansion)
Each can occur in either the transverse or Each can occur in either the transverse or longitudinal directions.Also specialty joints (e g transitions terminal Also specialty joints (e.g., transitions, terminal joints in continuously reinforced, etc.).
Types of Joints
Transverse Contraction:
Types of Joints
Longitudinal Contraction:g
Types of Joints
Transverse Construction:
Types of Joints
Longitudinal Construction:g
Formula for Maximum Joint Spacing
ML = T x CssML = Maximum length between joints (in.)T = Slab thickness (in.)Cs = Support constant
Use 24 for subgrades or unstabilized [granular] subbases;Use 21 for stabilized subbases (ATB, CTB, lean concrete) or existing concrete or asphalt pavement;Use 12 to 15 for thin bonded overlays on asphaltUse 12 to 15 for thin bonded overlays on asphalt
Effects of Joint Spacing
70%
80%
20 ft
50%
60%
70%ac
king
30%
40%
50%
nt s
lab
cra
18 ft
10%
20%
30%
Perc
en
17 ft
0%
10%
0 10 20 30 40 50T ffi illi ESAL
15 ft
Traffic, million ESALs
Crack Control Window
Too Late:Cracking
SawingWindow
Too Early:Raveling gg
Stre
ngth Internal Stress Equals
Concrete Strength
Stre
ssC
oncr
ete Minimum Strength to Avert
Excessive Saw Cut Raveling
Inte
rnal
TimeTime
IMPORTANCE OF CURING!
Crack Prediction with HIPERPAV
Visit FHWA website to downloadMany factors considered in the program. Input parameters are job specific.p p j p
www.hiperpav.com
Levels of Raveling
Unacceptable:
Moderate:hihiwww.hiperpav.comwww.hiperpav.com
None:
Not Just Timing…DEPTH!
Joint Depth Recommendations
Transverse TRANSVERSE
T/4 on unstabilizedT/3 on stabilized
T/4 T/3
LongitudinalT/3
LONGITUDINALT/3
Timing is a factorT/3 T/3
Conventional Joint Sawing
Early Entry Joint Sawing
Quality Control/Quality Assurance
Quality Control/Quality Assurance
The process of constructing quality concrete p g q ypavements has many components:
Reasonable design and specifications.g pA well executed QC/QA program for all important parameters.High quality materials and uniform production/delivery. Quality construction methods.y
Quality Assurance (QA)
QA typically involves testing by the agency or its representative to determine compliance with representative to determine compliance with specifications
The most frequently used QA criteria for paving The most frequently used QA criteria for paving jobs include:
Sl b thi kSlab thickness
Concrete strength
Entrained air content
Ride quality
Quality Control (QC)
QC generally refers to testing by the contractorg y g yfor the purpose of process control and to ensure meeting or exceeding specificationsg g p
A comprehensive QC program is much more involved than QA because all aspects of the involved than QA because all aspects of the project must be proactively monitored (materials batching placement etc )(materials, batching, placement, etc.)
Qualifications
QC/QA personnel must be adequately trained p q y(and certified in a number of states)
The testing facilities must be certified The testing facilities must be certified
bRepeatability and reproducibility of results are p y p ycritical for both QC and QA functions
Basis for Testing
Random testing assumes that the results are gnormally distributed
The mean and standard deviation of test results The mean and standard deviation of test results are used to determine if the samples are within specified limitsspecified limits
Variability is due to the operator (and equipment), y p ( q p )the test procedure, and the material being tested
Precision and Bias
Established test procedures (ASTM, AASHTO) p ( )have accounted for test variability through precision and bias statementsp
All physical tests have built in variability that must be accounted for in some mannerbe accounted for in some manner
The following slide illustrates the problem in g pdetermining a “right answer”
Precision and Bias (cont.)
Record Keeping
Keeping accurate records is mandatory under Keeping accurate records is mandatory under QC/QA specifications and is highly desirable for any projectany project
Information must be clearly recorded in a logical d t ti and systematic manner
All pertinent information should be entered as it All pertinent information should be entered as it is received to avoid confusion later
Quality Control Charts
Quality control charts (QCC) are statistically y ( ) ybased and used primarily for process control
The graphical format of QCC permit a simple The graphical format of QCC permit a simple and effective means to determine when a specific process is trending out of limitsspecific process is trending out of limits
An example of standard tabular records and the pcorresponding QCC is shown in the following slide
Statistical Process Control
Concrete Batching QC
Uniformity between concrete batches in critical in producing a smooth and long-lasting in producing a smooth and long-lasting pavementTh f ll i t ti l h k d The following parameters are routinely checked during batching:
Aggregate moistureWater contentWater/cementitious materials ratio
Pl t lib ti d ti it i Plant calibration and continuous monitoring are required
ASTM Batching Tolerances
Construction Operations QC
Construction operations require many varied types of QC measures including the following:
• Concrete temperature at time of placementp p• Entrained air content
Consolidation (internal ibration)• Consolidation (internal vibration)• Dowel bar placement• Potential for many others depending on
specification requirements
Test Methods for QC/QA
Established testing procedures are generally balloted and approved by ASTM AASHTO or bothballoted and approved by ASTM, AASHTO, or bothRecently developed test procedures may not yet be approved but can still provide much needed information (e.g., AVA)Tests applicable to paving projects :
Materials and mix designMaterials and mix designPreconstruction verificationConstruction QC Construction QC
Summary
Concrete paving is a “simple” process.p g p pThe overall quality of the pavement relies on the following:following:
Pre-planning.Good quality materials & equipmentGood quality materials & equipment.Following through with the plan.And checking at every step in the process and making And checking at every step in the process and making adjustments where necessary.
Summary
High-quality concrete pavement is achieved with:g q y pAccurate line and grade control.Uniform, well compacted grade. Uniform, well compacted grade. Consistent concrete production and delivery.Consistent uninterrupted forward motion of paverConsistent, uninterrupted forward motion of paver.Adequate internal vibration.Timely texturing and curingTimely texturing and curing.
Top Related