1 of 10888-97-387-G-00 rev.C • 08/17
LX LCD Accessory Arm
User's Guide - EnglishGuía del usuario - EspañolManuel de l’utilisateur - FrançaisGebruikersgids - DeutschBenutzerhandbuch - NederlandsGuida per l’utente - ItalianoAnvändarhandbok - svenskaユーザーガイド : 日本語用户指南 : 汉语
IncludesConstant Force™Technology
ENGLISHASSEMBLY INSTRUCTIONS
For the latest User Installation Guide please visit: www.ergotron.com
CAUTION! The LX Arm Accessory is designed to be used with the 45-295 LX Desk Mount LCD Arm, Tall Pole and the 45-509 LX Dual Stacking Arm, Tall pole products. Using the LX Arm Accessory with any other product may create an unstable situation resulting in equipment damage and/or personal injury.
2 of 10888-97-387-G-00 rev.C • 08/17
7 - 20 lbs
(3.2 - 9.1 kg)
5°
70°360°
360°
180°
13"(330 mm)
360°
3x
4x
4x
13.7" (348 mm)
3x
20.7" (525 mm)
ENGL
ISH
Features & Specifi cations
Can have up to 4 arms on a pole when used with the 45-509
LX Dual Stacking Arm, Tall pole
See updated maximum weight capacities:
11 lbs (5 kg)
per monitor
Max Monitor Width:
11 lbs (5 kg)
per monitor
11 lbs (5 kg)
per monitor
11 lbs (5 kg)
per monitor
Max Monitor Width:
Maximum monitor width will decrease depending on arm confi guration.
Maximum monitor width will decrease depending on arm confi guration.
3 of 10888-97-387-G-00 rev.C • 08/17
A B C D
1
2
3
4
M4 x 10mm4x
M4 x 10mm
4x
4mm1x
1x
1xM3 x 6mm
1x1x
2x
2.5mm1x
1x
1x
1x 4x
10 - 24 x 1/2”1/8”
ENGLISH
Tools Needed
Components
4 of 10888-97-387-G-00 rev.C • 08/17
1
WARNING
M4 x 10mm
M4 x 10mm
4x
4x
0°
M3 x 6mm
1x
ENGL
ISH
WARNING! Stored Energy Hazard: The arm mechanism is under tension and will move up rapidly, on its own, as
soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the arm has been
moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or
equipment damage!
5 of 10888-97-387-G-00 rev.C • 08/17
2 2.5mm
ENGLISH
CAUTION! The LX Arm Accessory is designed to be used only with the 45-295 LX Desk Mount LCD Arm, Tall Pole product, with a total of two (2) arms per pole. Using the LX Arm Accessory with any other product or in quantities greater than two (2) arms per pole may create an unstable situation resulting in equipment damage and/or personal injury.
6 of 10888-97-387-G-00 rev.C • 08/17
3 2.5mm
ENGL
ISH
7 of 10888-97-387-G-00 rev.C • 08/17
4
ENGLISH
NOTE: Leave enough slack in cable to allow full range of motion.
Caution: To avoid the potential to pinch cables it is important to follow the cable routing
instructions in this manual. Failure to follow these instructions may result in equipment
damage or personal injury.
8 of 10888-97-387-G-00 rev.C • 08/17
5
4mm
a
ENGL
ISH
CAUTION: DO NOT overtighten fasteners.
Overtightening may cause damage to your
equipment.
Increase Lift StrengthIf the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase Lift Strength:
Decrease Lift StrengthIf the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease Lift Strength:
Adjustment StepImportant! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
Lift – Up and down
9 of 10888-97-387-G-00 rev.C • 08/17
4mm
b
0°
M3 x 6mm
c
d
2.5mm
ENGLISH
Increase FrictionIf this product moves too easily, then you'll need to increase friction:
Decrease FrictionIf this product is too diffi cult to move, then you'll need to decrease friction:
Increase FrictionIf this product moves too easily, then you'll need to increase friction:
Decrease FrictionIf this product is too diffi cult to move, then you'll need to decrease friction:
CAUTION: DO NOT remove screw. Removing screw may cause damage to
equipment.
Tilt – Forward and Backward
Arm Swing – Side-to-side
Rotate – Portrait/Landscape
10 of 10888-97-387-G-00 rev.C • 08/17
© 2015 Ergotron, Inc. All rights reserved.
ENGL
ISH
Learn more about ergonomic computer use at:
www.computingcomfort.org
Set Your Workstation to Work For YOU!
Height Position top of screen slightly below eye level. Position keyboard at about elbow height with wrists fl at. Distance Position screen an arm's length from face—at least 20” (508mm). Position keyboard close enough to create a 90˚ angle in elbow. Angle Tilt screen to eliminate glare. Tilt the keyboard back 10° so that your wrists remain fl at.
To Reduce FatigueBreathe - Breathe deeply through your nose.Blink - Blink often to avoid dry eyes.Break • 2 to 3 minutes every 20 minutes• 15 to 20 minutes every 2 hours.
For local customer care phone numbers visit: http://contact.ergotron.comFor Service visit: www.ergotron.comFor Warranty visit: www.ergotron.com/warranty
Top Related