AP-65-MNT-WJ Access Point EnclosureInstallation Guide
IntroductionThe AP-65-MNT-WJ access point (AP) enclosure allows you to install an Aruba Networks AP-65 access point on the wall, directly over an installed junction box.
The AP-65-MNT-WJ kit includes the following pieces:
Plastic base plate to attach over a standard installed junction box
Plastic wall box
One of the following plastic faceplate styles (depending on which model you ordered):
Three openings for Krone, Keystone, or Leviton connectors
Three openings for Siemon 45° connectors
Blank
Blank fillers as needed for unused faceplate openings
Two screws to attach the faceplate to the enclosure:
Pan-head screw
Torx screw with matching Torx key
Labels and cover windows
Before You Install the AP EnclosureYou need the following tools to install the AP enclosure:
Screwdriver to match the screws in the cover plate over the installed junction box
#1 Phillips screwdriver for the cover plate retaining screw on the AP enclosure
(Optional) side cutters or similar tool to cut out openings for cable raceways or power connection access
To use the enclosure with surface mounted cable raceways, prepare the box before installation. On the inside of the box, at the top and bottom, are marked areas that you can cut out to allow cable access (see Figure 1).
To use an external power supply, cut out the marked area at the lower right corner of the box (see Figure 1).
0510381-01 | July 2007 1
Figure 1 Access cutout areas on enclosure box
Installing the AP EnclosureTo install the AP enclosure:
1. Attach the base plate as follows:
a. Remove the cover plate from an installed Ethernet wall jack (Figure 2). Save the screws.
Figure 2 Removing the installed cover plate
2 AP-65-MNT-WJ Access Point Enclosure | Installation Guide
b. Snap the cable connectors out of the removed cover plate and set the cover plate aside. Identify the Ethernet cable that will be connected to the AP-65. The Ethernet cable must have a male RJ-45 connector.
c. Attach the enclosure base plate to the junction box using the screws from the removed cover plate (Figure 3).
Figure 3 Attaching the base plate
2. Connect the Ethernet cable to the port on the back of the AP-65. Hold the unused cables up and out of the way as you continue with the next step.
3. Attach the AP-65 to the mounted base plate as follows:
a. Position the antennas on the AP-65 along the sides of the unit.
b. Locate the mounting posts on the base plate and the mounting holes on the AP-65 (Figure 4).
AP-65-MNT-WJ Access Point Enclosure | Installation Guide 3
Figure 4 Preparing to attach the AP-65
c. Align the AP-65 mounting holes over the posts on the base plate.
d. Push the AP-65 against the pegs and downward, until the pegs engage the slots at the top of the mounting holes.
e. Rotate the antennas on the AP-65 upward (Figure 5).
Figure 5 Attaching the AP-65
N O T E
Be sure to extend the antennas on the AP-65 unit before you attach the wall box. If the antennas are not extended, the AP-65 will not deliver optimum performance.
4 AP-65-MNT-WJ Access Point Enclosure | Installation Guide
4. Attach the wall box as follows:
a. Hold the box with the ventilation slits at the sides and bottom of the box, and align the box with the mounted base plate (Figure 6).
b. Snap the box onto the base plate; press first one side and then the other side over the snap-fit retaining tabs.
Figure 6 Attaching the box
AP-65-MNT-WJ Access Point Enclosure | Installation Guide 5
5. Select the appropriate cover plate for the AP-65 enclosure. If additional cables are routed through the junction box, snap their connectors into the openings in the cover plate (Figure 7). Insert blanks into any unused openings.
Figure 7 Attaching cables to the cover plate
6. Set the cover plate over the wall box and secure it using one of the provided screws (Figure 8).
Figure 8 Attaching the cover
7. (optional) Apply labels to the cover plate over the mounting screw and the LED viewing openings.
6 AP-65-MNT-WJ Access Point Enclosure | Installation Guide
AP-65-MNT-WJ Access Point Enclosure | Installation Guide 7
Contacting Aruba
Web Site Support
Main Site http://www.arubanetworks.com
Support Site http://www.arubanetworks.com/support
Software Licensing Site https://licensing.arubanetworks.com
Wireless Security IncidentResponse Team (WSIRT)
http://www.arubanetworks.com/support/wsirt.php
Support Email [email protected]
WSIRT EmailPlease email details of any securityproblem found in an Aruba product.
Telephone Support
Aruba Corporate +1 (408) 227-4500
FAX +1 (408) 227-4550
SupportUnited StatesFranceUnited KingdomGermanyAll Other Countries
800-WI-FI-LAN (800-943-4526)+33 (0) 1 70 72 55 59+44 (0) 20 7127 5989+49 (0) 69 38 09 77 22 8+1 (408) 754-1200
© 2007 Aruba Networks, Inc. All rights reserved.
www.arubanetworks.com
1322 Crossman AvenueSunnyvale, California 94089
Phone: 408.227.4500Fax 408.227.4550
8 AP-65-MNT-WJ Access Point Enclosure | Installation Guide
Top Related