POWER ELECTRONICSS.No CODE PROJECT TITLE
1 ET13PE1
Voltage-Based Control of a Smart Transformer in a Micro grid
DESCRIPTION
For the islanded operation of a micro grid, several control strategies have been developed. For example, voltage based droop control can be implemented for the active power control of the generators & the control of the active loads.
2 ET13PE2
Novel High Step-Up DC–DC Converter for Distributed Generation System
DESCRIPTION
In this paper, a novel high step-up dc–dc converter for distributed generation systems is proposed. Concept is to utilize two capacitors & one coupled inductor. The two capacitors are charged in parallel during the switch-off period and are discharged in series during the switch-on period by the energy stored in the coupled inductor to achieve a high step-up voltage gain.
3 ET13PE3
Maximum Power Point Tracking Technique for Partially Shaded Photovoltaic Systems in Micro grids
DESCRIPTION
A modified fuzzy-logic controller for maximum power point (MPP) tracking is proposed to increase photovoltaic (PV) system performance during partially shaded conditions. Instead of perturbing and observing the PV system MPP, the controller scans and stores the maximum power during the perturbing and observing procedures.
4 ET13PE4
Digital Control for an ArcWelding Machine Based on Resonant Converters and Synchronous Rectification
DESCRIPTION
This paper presents a optimized drive signals for resonant converters using synchronous rectification (SR) applied to an arc welding machine.
5 ET13PE5
An Energy-Stored Quasi-Z-Source Inverter for Application to Photovoltaic Power System
This paper proposes a new topology of the energy-stored
DESCRIPTION
qZSI. The operating characteristic of the proposed solution is analyzed in detail. 2-strategies are proposed with the related design principles to control the new energy-stored qZSI when applied to the PV power system.
6 ET13PE6
Battery Charger for Electric Vehicle Traction Battery Switch Station
DESCRIPTION
This paper presents the functionality of a commercialized fast charger for a lithium-ion electric vehicle propulsion battery. The device is intended to operate in a battery switch station, allowing an up-to 1-h recharge of a 25-kWh depleted battery.
7 ET13PE7
Bifurcation Analysis of Standalone Photovoltaic- Battery Hybrid Power System
DESCRIPTION
Standalone photovoltaic-battery hybrid power systems are attractive renewable power generation systems, a popular form of which is based on a photovoltaic system and a battery connected to an output dc bus via a buck converter & a bidirectional buck/boost converter.
8 ET13PE8
Boost rectifier using single phase matrix converter with reduced switch counts
DESCRIPTION
This paper focuses on implementation of computer simulation for boost rectifier operation using single-phase matrix converter topology with reduced switch counts. Proposed topology employed only six switches compared with the conventional boost rectifier operation using single phase matrix converter topology used eight main switches.
9 ET13PE9
New Extendable Single-Stage Multi-Input DC-DC/AC Boost Converter
DESCRIPTION
This paper presents a new extendable single-stage multi-input DC-DC/AC boost converter. The proposed structure comprises two bidirectional ports in the converter central part to interface output load and battery storage, and several unidirectional input ports to get powers from different input dc sources.
10 ET13PE10
A Modified Single-Phase Quasi-Z-Source AC–AC Converter
DESCRIPTION
A modified single-phase quasi-Z-source ac–ac converter is proposed in this paper. Proposed converter has the main features in that the O/P voltage can be bucked or boosted and be both in-phase& out-of-phase with the I/P voltage
11 ET13PE11
Highly Efficient Analog Maximum Power Point Tracking (AMPPT) in a Photovoltaic System
DESCRIPTION
Compact-size analog maximum power point tracking (AMPPT) technique is proposed in this paper for high power efficiency in the photovoltaic (PV) system. Combining existing MPPT approaches, we present a fast & accurate tracking performance.
12 ET13PE12
A New Cascaded Multilevel Inverter withReduced Number of Switches
DESCRIPTION
This paper propose a new topology for cascaded multilevel inverters. This structure consists of series connection of proposed basic unit blocks which are built with both unidirectional and bidirectional switches.
13 ET13PE13
Boost-Derived Hybrid Converter with simultaneous DC and AC outputs
DESCRIPTION
The paper proposes a family of hybrid converter topologies which can supply simultaneous DC as well as AC loads from a single DC input. These topologies are realized by replacing the controlled switch of single-switch boost converters with a voltage source inverter (VSI) bridge network.
14 ET13PE14
Flexible Multilevel Boost DC-AC Converter
DESCRIPTION
In this paper, incorporation of MULTI-output boost (MOB) converter by multilevel inverter is proposed. Renewable energy sources such as fuel cell and photovoltaic produce low level of voltage. So to increase the magnitude of voltage, dc-dc boost converter is used.
15 ET13PE15
Improved ZVS DC-DC Converter With a High Voltage Gain and a Ripple-Free Input Current
DESCRIPTION
An improved zero-voltage-switching (ZVS) dc-dc converter with high voltage gain & ripple-free I/P current is proposed. It consists two converter cellsa boost cell and an asymmetrical pulse-width-modulation (APWM) full-bridge cell. Boost cell in the proposed converter has capabilities of providing a ripple-free i/p current.
16 ET13PE16
A Soft Switching Three-phase Current-fed Bidirectional DC-DC Converter With High Efficiency Over a Wide
Input Voltage Range
DESCRIPTION
In this paper, a three-phase current-fed dual-activebridge (DAB) bidirectional DC-DC converter is presented. Compared to the voltage source DAB converter, the proposed converter allows low RMS current and maintains zero voltage switching (ZVS) in the whole operating range by keeping the ratio between primary side and secondary side DC-link voltage constant, leading to high efficient energy conversion over a wide input voltage range.
17 ET13PE17
Cascade Three-Level AC/AC Direct Converter
DESCRIPTION
This paper proposes a novel family of cascade threelevel (TL) ac–ac direct converters based on ac switch cells, which transfer unsteady high ac voltage with distortion into regulated sinusoidal voltage with low total harmonic distortion (THD).
18 ET13PE18
Grid-Connected Boost-Half-Bridge Photovoltaic Microinverter System Using Repetitive Current Control
and Maximum Power Point Tracking
DESCRIPTION
This paper presents a novel grid-connected boost half- bridge photovoltaic (PV) micro inverter system and its control implementations. In order to achieve low cost, easy control, high efficiency, and high reliability, a boost-half-bridge dc–dc converter using minimal devices is introduced to interface the low-voltage PV module.
19 ET13PE19
Novel Zeta-Mode Three-Level AC Direct Converter
DESCRIPTION
An improved zero-voltage-switching (ZVS) dc-dc converter with a high voltage gain and a ripple-free input current is proposed. It consists of two converter cells—a boost cell and an asymmetrical pulse-width-modulation (APWM) full-bridge cell. Boost cell in proposed converter has capabilities of providing ripple-free I/p current.
20 ET13PE20
Step-Up DC/DC Converters With Cascaded Quasi-Z-Source Network
DESCRIPTION
The proposed cascaded qZSI inherits all the advantages of the traditional solution .Moreover, as compared to the conventional qZSI, the proposed solution reduces the shoot-through duty cycle by over 30% at the same voltage boost factor.
POWER SYSTEMS.No CODE PROJECT TITLE
1 ET13PS1
Improvement of power quality by using hybrid fuzzy controlled based IPQC at various load conditions
DESCRIPTIONThis paper presents a hybrid fuzzy logic controlled based improved power quality conditioner used to counterbalance for harmonic distortion in 3-phase system.
2 ET13PS2
A Method for Evaluating Energy Efficiency to Justify Power Factor Correction in Ship Power Systems
DESCRIPTION
This paper presents the methodology and results for the economic evaluation of PFC in marine vessels. A mathematical model, used to determine the relationships among fuel oil consumption, emission and power factor for the diesel electric generator, is derived to quantify the possible benefits with PFC.
3 ET13PS3
Reactive Power Compensation in Single-Phase Operation of Microgrid
DESCRIPTION
A coordinated control of distributed generators (DG) and distribution static compensator (DSTATCOM) in a micro grid is proposed in this paper. With high penetration of distributed sources and single-phase operation of the system, voltage unbalance can often go beyond the acceptable limit.
4 ET13PS4
Technique to Develop Auto Load Shedding &Islanding Scheme to Prevent Power System Blackout
DESCRIPTION
Abnormal condition in a power system generally leads to a fall in system frequency, and it leads to system blackout in an extreme condition. This paper presents a technique to develop an auto load shedding and islanding scheme for a power system to prevent blackout and to stabilize the system under any abnormal condition.
5 ET13PS5
Stabilty Of Power Transmission Capability Of Hvdc System Using Facts Controllers
DESCRIPTION
a desired power condition at the given points are best achieved using power controllers such as the well known High Voltage Direct Current (HVDC) and Flexible Alternating Current Transmission System (FACTS) devices.
6 ET13PS6
Multi objective Optimal Location of FACTS Shunt-Series Controllers for Power System Operation Planning
DESCRIPTION
This paper develops appropriate models of flexible AC transmission systems (FACTS) shunt-series controllers for multiobjective optimization and also presents a multiobjective optimization methodology to find the optimal location of FACTS shunt-series controllers.
7 ET13PS7
Investigation of Domestic Load Control to Provide Primary Frequency Response Using Smart Meters
DESCRIPTION
The ability of smart meters to control domesticdemand during system emergencies was investigated. In ths project load control scheme that used a local frequency measurement from the smart meters was investigated.
POWER SECTORS S.No CODE PROJECT TITLE
1 ET13PT1
Computer based Boiler Feed Pump protection and changeover scheme
DESCRIPTION
The Aim of this project is for protecting the Boiler Feed Pump failure and using a changeover scheme by monitoring the required parameters using pc for the continuous power generation.
2 ET13PT2
Incapability of analog relay protection to detect generator stator winding ground failures at neutral end
DESCRIPTION
The electromechanical ground protection relay 59GN commonly used in generator protection does not respond to grounds in the bottom ~5% of the stator winding. this paper will describe newer ground relay systems that monitor and protect the entire stator winding for grounds.
3 ET13PT3
Self-adaptive transformer differential protection
DESCRIPTION
Setting the pickup current and slope of differential relays of power transformer protection is a well-known compromise. It has been the focus of study to improve both the security and sensitivity of transformer differential protection recently. Therefore a novel adaptive protection criterion is proposed in this study,
4 ET13PT4
Application of computer and modern automation system for protection and optimum use of High voltage power
transformer
DESCRIPTION
In this paper an attempt has been made to elaborate the use of computer and modern automation system for protection and optimum use of High voltage power transformer, its advantages and cost effectiveness. Programmable logic controllers (PLC) can be used for control & automation of High voltage power transformer.
5 ET13PT5
Switching and protection of multiple transformer arrangement in industrial distribution system
DESCRIPTION
In modern industrial electrical distributions, medium size transformers require protection systems that are faster, more reliable and selective than the systems used for their earlier counterparts. To achieve such improved
performance, this system is used
6 ET13PT6
Research on the intelligent protection system of coal conveyor belt
DESCRIPTION
A sort of intelligent protection system for conveyor belt was designed, which mainly aimed at the phenomenon of belt slipped, belt broken, overloaded and coupling broken etc. It was designed by using intelligent instrument, monitoring software and fault detection technology, The protection system can automatically detect, diagnose corresponding fault, and give alarm signal with sound and light to stop the fault belt machine in due course. The application effect has proved that the protection system can improve intelligent degree of the whole burning coal transport and reduce the manual greatly and save a lot of funds for enterprise
7 ET13PT7
An Adaptive Fuzzy Mho Relay for Phase Backup Protection With Infeed From STATCOM
DESCRIPTION
This paper presents a fuzzy-logic-based scheme for the operation of generator-phase backup distance protection, otherwise popularly known as “phase 21” function, in the presence of a STATCOM installed at the generator bus.
8 ET13PT8
Impact of Power System Instability on Generator Protection
DESCRIPTION
This paper discusses what relay engineers need to know about power system stability, including the four basic types of power system instability. Voltage instability, Steady-state instability, Transient instability &Dynamic instability.
9 ET13PT9
Research on the intelligent protection system of coal conveyor belt
DESCRIPTION
A sort of intelligent protection system for conveyor belt was designed, which mainly aimed at the phenomenon of belt slipped, belt broken, overloaded and coupling broken etc. The protection system can automatically detect, diagnose corresponding fault, and give alarm signal with sound and light to stop the fault belt machine in due course.
10 ET13PT10
Modeling and Simulation of Digital Frequency Relay for Generator Protection
DESCRIPTION
This paper presents the design and various data conversion steps of a digital frequency relay. The designed relay will cover both over and under frequency conditions.
11 ET13PT11
Modeling and Simulation of Digital Negative Sequence Relay for Unbalanced Protection of Generator
DESCRIPTIONThis paper presents design & various data conversion steps of a digital negative sequence relay.
12 ET13PT12
Modeling and Simulation of Reverse Power Relay for Generator Protection
DESCRIPTIONThe paper has presented the modeling of digital reverse power relays
13 ET13PT13
Protection of Transformer-Ended Feeders Using Multifunction Relays
DESCRIPTION
In this paper, we describe an application of digital multifunction relays for the protection of a feeder that ends with a distribution transformer. In this application, we attempt to provide as many protection functions as possible with fewest relays.
14 ET13PT14
A Novel Adaptive Dispersed Phase Current Differential Protection Criterion
DESCRIPTION
A novel adaptive dispersed phase current differential protection criterion is proposed in this paper, and an objective function with the independent variable of fault current component and through current is defined to revise the restraining ratio of differential protection criterion adaptively.
15 ET13PT15
Analysis and Solutions of Overcurrent Protection Issues in a Micro grid
DESCRIPTION
In this project The changes cause detrimental effect of sympathetic tripping, blinding of protection, relay over-reaching, relay under-reaching and loss of selectivity of the over current protection scheme of generators in micro grid are discussed
16 ET13PT16
Adaptive Differential Protection for Power Transformer Based on Transient Signal Analysis
DESCRIPTIONThis paper presents an adaptive relaying scheme for percentage differential protection of 3-phase power transformers.
17 ET13PT17
A New Algorithm to Avoid Maloperation of Transformer (TFr) Differential Protection in Substations With an
Inner Bridge Connection
DESCRIPTION
This paper analyzes the factors that may lead to the maloperation of transformer differential protection and concludes that local transient saturation of the current TFr (CT) caused by the decaying dc component in the magnetizing inrush is the main cause of the maloperation of the TFr differential protection.
18 ET13PT18
A Real Time DSP based Differential Protection of Low Voltage Bus bar
DESCRIPTION
This paper presents design, implementation and testing of low voltage bus bar relaying scheme in laboratory environment using A Digital Signal Processor.
19 ET13PT19
Application of Intelligent Relays to the Islanding protection of Multiple Synchronous Generators
DESCRIPTION
This article illustrates how intelligent relays can be used to address DG islanding detection issues spawned by the presence of more than one synchronous generator on a distribution feeder.
20 ET13PT20
A Secure Generator Distance Phase Backup Protection Setting for Enhancing Generator Over excitation Thermal Capability during System Disturbances
DESCRIPTION
In this paper, investigations are carried out to explore the impact of generator distance phase backup protection (Relay (21) on the generator over excitation thermal capability.
EMBEDDED & Robotics S.No CODE PROJECT TITLE
1 ET13EM1
A System for Mobile Assisted Living
DESCRIPTION
The system can detect abnormal situations with the person wearing the wearable part ofthe system (e.g. abnormal heart rate) and send this information to the nursing home so that appropriate action can be taken immediately.
2 ET13EM2
Wireless remote monitor and control system based on Zigbee and web
DESCRIPTION
Considering the present development trend of intelligence, convenience and remoteness in equipment monitoring area, our system employs intelligent sensors based on ZigBee wireless communication technology and executable elements, which is integrated with web applications based on network environment is introduced in this project
3 ET13EM3
Low cost smart power metering
DESCRIPTION in this paper a low cost solution for the real-time energy management in a smart grid, is presented. It provides several smart meters, which act as slaves, that continuously monitor connected loads communicating with data aggregator via CAN-bus.
4 ET13EM4
Remote-Control System of High Efficiency and Intelligent Street Lighting Using a ZigBee Network of
Devices and SensorsDESCRIPTION The proposed remote-control system can optimize
management and efficiency of street lighting systems. It uses ZigBee-based wireless devices which enable more efficient street lamp-system management,
5 ET13EM5
Automatic speed and torque monitoring in induction motors using ZigBee and SMS
DESCRIPTION This project is for monitoring the speed and torque in induction motors in real time by employing ZigBee based wireless sensor network. The values calculated by the embedded system are transmitted to a monitoring unit through ZigBee based wireless sensor network.
6 ET13EM6
A RISC Microcontroller Based Voltage Regulator Module with Fuzzy Logic Controller for Processor Core
in Mobile SystemsDESCRIPTION This paper describes the design of Buck converter that has
a fuzzy controller implemented using a RISC based microcontroller from Atmel series along with a choice of hardware components that will ensure better efficiency while delivering good stability and a dynamic response that complies with requirements of the target processor.
7 ET13EM7
Advanced Virtual Embedded System Laboratory
DESCRIPTION
In this virtual web based laboratory a student can perform experiments, simulations and experimental validation of results virtually using a single PC.
8 ET13EM8
A low cost web based remote monitoring system with built-in security feature for vulnerable environments
DESCRIPTION
This paper mainly focus on the design and implementation of an intelligent, low cost and fully automated system which will be able to provide full time monitoring and eventual security to susceptible environment like gas filling station, research and development laboratories etc.
9 ET13EM9
Automatic Control for Laboratory Sterilization Process based on Arduino Hardware
DESCRIPTION
In this paper An automated control system for the sterilization process of biological material is introduced. The proposed system is composed of four modules: flame detection, pressure sensor, Gas Control Module and CPU Module. This System is based on Arduino Board.
10 ET13EM10
Online Control of Fuzzy Based Mine Detecting Robot Using Virtual Instrumentation
DESCRIPTION
In the real time applications detection & location of bomb is highly essential in the field of defense applications. This paper proposes the design of a micro-controller based fuzzy logic controller for a remote controlled mine detecting robot.
11 ET13EM11
Design and Conceptual Development of a Sunbathe Laundry Robot
DESCRIPTION
The main objective of this project is to design and develop a prototype that base on light detection sensor and water detection circuit with both parameters interface with twin motor gearbox for movement purpose.
12 ET13EM12
Design and Implementation of Industrial Network Monitoring Protocol for Networked Industrial Sensors
DESCRIPTION
in this project a Industrial Network Monitoring Protocol is proposed. the proposed protocol provides device message sets. For maintainability, it provides the fault detection and reporting. For the user’s convenience, it provides a categorized addressing system.
13 ET13EM13
Automatic Measurement and Reporting System of Water Quality Based on GSM
DESCRIPTION
The system consists of multiple sensors of water quality testing, single-chip microcontroller data acquisition module, information transmission module, monitoring center and other Accessories. Various parameters of water quality are automatically detected and the data are instantaneously sent to monitoring center by GSM network in the form of SMS.
14 ET13RO1
Developing a 32-bit microcontroller board for embedded applications
DESCRIPTION
This paper describes development of a 32-bit embedded microcontroller board intended for a broad range of applications.
15 ET13RO2
Online control of remote operated agricultural Robot using Fuzzy Controller and Virtual Instrumentation
DESCRIPTIONThis paper details the design of a micro-controller based fuzzy logic controller for an agricultural Robot which can be used for plugging, seeding and soil moisture sensing.
LABVIEWS.No CODE PROJECT TITLE
1 ET13LV1
Online control of remote operated agricultural Robot using Fuzzy Controller and Virtual Instrumentation
DESCRIPTION
This paper details the design of a micro-controller based fuzzy logic controller for an agricultural Robot which can be used for ploughing, seeding and soil moisture sensing
2 ET13LV2
Virtual Lab: Remote Access and Speed Control of DC Motor using Ward-Leonard System
DESCRIPTION
The objective of this project is to demonstrate the real-time web based laboratory experiment conduction by accessing the laboratory set-up from a remote location and measure the experimental parameters by generating the control commands at a distant client.
3 ET13LV3
The Design of ZigBee Protocol Based Mobile Node in Wireless Sensor Network
DESCRIPTION
In order to overcome the defects of static wirelesssensor network nodes, such as poor adaptability, communication disruption, lack of dynamic network & so on, a kind of approach to design mobile wireless sensor node is proposed in this paper.
4 ET13LV4
Remote Monitoring and Controlling of Gas Sensors Using VPN Connection
DESCRIPTION
The use of sensors is witnessing a dramatic increase. They are applied in diverse fields such as military, industrial, health, and smart homes. Monitoring these sensors could be made remotely with the help of communication networks. Using Labview
5 ET13LV5
Oxygen Level Monitoring in an Oxygen Cylinder
DESCRIPTION
The amount of oxygen present inside the cylinder is measured by the pressure at the outlet nozzle. The pressure is measured using a high precision MEMS Pressure Sensor & displayed in Labview.
6 ET13LV6
Experiential Learning of Digital Communication Using LabVIEW
DESCRIPTION
. This paper discusses the design & implementation of laboratories and course projects using Labview in instrumentation course. Pedagogical challenge is to enhance students’ learning of digital communication using LabVIEW.
7 ET13LV7
Data Acquisition and Realization of Communication Transmission Based on Labview
DESCRIPTION
Through the Internet we can make the virtual experiments platform published on the web, sharing resources and avoid duplication of equipment purchased and waste of resources. A lot of data acquisition and wireless communication framework was developed based on graphic programming platform of Labview.
8 ET13LV8
Novel Design Solutions for Remote Access, Acquire and Control of Laboratory Experiments on DC Machines
DESCRIPTION
This paper presents the novel design techniquesto access experiments on electrical machines remotely through the Web using virtual instrumentation (VI) tools.
9 ET13LV9
LabVIEW Based Automatic Paralleling of Synchronous Generator System
DESCRIPTION This paper describes the development & implementation of automatic paralleling of synchronous generator system using Labview platform.
10 ET13LV10
Online Control of Fuzzy Based Mine Detecting Robot Using Virtual Instrumentation
DESCRIPTION
In the real time applications the detection andlocation of bomb is highly essential in the field of defense applications. Considering the value of human life the robot is allowed in the field to detect the bomb.
RASPBERRY PiS.No CODE PROJECT TITLE
1 ET13RP1
Proposal of Sensor Data Gathering with Single Board Computer
DESCRIPTION
We propose a sensor data gathering system using a single board computer for home energy management systems. This sensor system should be capable of handling 100 sensor data per second. Since a single board computer has low power consumption and low performance, it is used as the sensor data gathering server.
2 ET13RP2
Building network appliances with NanoBSD operating system on Single Board Computers
DESCRIPTION
There is presented an overview what NanoBSD operating system is and how to use it in building powerful network appliances on Single Board Computers (SBC). The supposed audience of this paper is IT/network engineers, researchers, students, Unix/Linux or BSD fans with interest focused on building their own network appliances based on embedded computers
3 ET13RP3
Evaluation of clock synchronization methods for measurement and control using embedded Linux SBCs
DESCRIPTION
This paper reports a study and practical evaluation of two different clock synchronization methods for distributed measurement and control nodes based on Linux Single Board Computers (SBCs) with ARM processors and communicating through a TCP/IP wide area network.
4 ET13RP4
An improved real-time surveillance system for home security system using BeagleBoard SBC, Zigbee and FTP
webserver
DESCRIPTION
A number of surveillance devices in a Zigbee protocol (IEEE 802.15.4) based wireless network are connected to a Beagle-Board Single Board Computer (SBC) based surveillance management system. Remote alerting on fire and intruder detection are the key features of the system. When smoke or intruder movement is detected, the system sends warning messages through Short Message Service (SMS) to cell phones, starts capturing real-time video for fixed duration and makes the alarm on.
INDUSTRIAL AUTOMATION & PLC
S.No CODE PROJECT TITLE
1 ET13iP1
Utilization of the PLC as a web server for remote monitoring the technological process
DESCRIPTION
This paper presents a new methodology to develop remote laboratories for systems engineering and automation control courses, based on the combined use of TwinCAT, a laboratory Java server application, and Easy Java Simulations (EJS). The TwinCAT system is used to close the control loop for the selected plants by means of programmable logic controllers (PLCs) deployed in PCs with the a run-time tool.
2 ET13iP2
Remote Control Laboratory Using EJS Applets and TwinCAT Programmable Logic Controllers
DESCRIPTION
This paper presents how it is possible to utilize PLC in the task of the Web server. Described is configuration of the PLC and its connection to the computer network. Next is described principle of creation dynamic web page and described are function for process variable data read and write.
3 ET13iP3
Development of a Low Cost Programmable Logic Controller
DESCRIPTION
The aim of this study is to develop a low cost small module (hardware card), for use in the automation of simple machines and equipments. programmable logic controller (PLC) will be part of an open platform that also contains a free software tool for programming PLC in C language & online tutorial with detailed instructions about building & programming the system.
4 ET13iP4
Optimization through artificial neural network on a Programmable Logic Controller for a Sludge Drying
Plant
DESCRIPTION
The Sludge Drying Plant (SDP) is the final processing facility of Effluent Treatment System (ETS) that produces bio-sludge cake before it is sent out for final disposal. Due to the process disturbances, mechanical and inconsistent chemical reactions, the amount dry solid is reduced tremendously.
5 ET13iP5
Programmable Logic Controller (PLC) for polymer mixing tank
DESCRIPTION
The process requires manually mixing the cationic polymer long chains with raw water to produce a product that will be sent to the sludge tank process and filter press process where the sludge will harden for disposal.
6 ET13iP6
Design and fabrication of Programmable Logic Controller Kit with multiple output module for teaching
and learning purposes
DESCRIPTION
The existing PLC trainer board comes with a casing where students have the difficulty in observing and understanding the connection between the input module, PLC controller and output modules. The development of PLC Kit has been designed and improved by increasing the number of input and output components, cost reduction and it is also user friendly.
DIGITAL IMAGE PROCESSINGS.No CODE PROJECT TITLE
1 ET13iM1
Research on edge detection algorithm for plate image
DESCRIPTION
In view of the problems that traditional edge detection algorithms are sensitive to noise and the environment of plate scene is complex, plate image is smoothed with Gaussian filter, and by comparison of edge images from non-subsampled contour let edge detection algorithm and multi-scale wavelet edge detection algorithm, a new algorithm, pulse coupled neural network edge detection algorithm based on multi-scale wavelet transform is proposed.
2 ET13iM2
A Flexible Method For Recognizing Four-Digit Numbers On A License-Plate In A Video Scene
DESCRIPTION
In order to realize a simple system for monitoring car movements, a flexible method was developed for recognizing four-digit numbers on a license-plate in a video scene. The method consisted of three parts; global search for finding a license plate in a scene, corner detection for removing shape deformation, and numeral character recognition. The spatial features and the spectral (color) ones were merged and processed at a time in the global search.
3 ET13iM3
An adaptive threshold edge detection method based on the law of gravity
DESCRIPTION
This algorithm make up for the traditional algorithm in the whole image only used a single threshold. Through the experimental comparison, this paper algorithm can create dynamic adaptive threshold value. The algorithm has good inhibition effect used in image with salt and pepper noise and gaussian noise. it can extract image edge efficiently.
4 ET13iM4
Facial Feature Extraction With A Depth Aam Algorithm
DESCRIPTION
The main idea of our method is to use the face detection algorithm with a Kinect camera to accurately locate human head and estimate head pose. A depth AAM algorithm is developed to locate the detailed facial features. Experimental results show that our depth AAM algorithm can effectively and accurately locale facial features from video objects in conditions of complex backgrounds and various poses.
5 ET13 iM5
An Informed Watermarking Scheme Using Hidden Markov Model In The Wavelet Domain
DESCRIPTION
This paper presents a new informed image watermarking scheme with high robustness and simplified complexity. Simulation results demonstrate that the proposed informed watermarking algorithm has high robustness against common attacks in signal processing and shows a comparable performance to the state-of-the-art scheme with a greatly reduced arithmetic complexity.
6 ET13 iM6
A Novel Data Embedding Method Using Adaptive Pixel Pair Matching
DESCRIPTION
This paper proposes a new data-hiding method based on pixel pair matching (PPM). The basic idea of PPM is to use the values of pixel pair as a reference coordinate, and search a coordinate in the neighborhood set of this pixel pair according to a given message digit. Experimental results reveal that the proposed method not only provides better performance than those of OPAP and DE, but also is secure under the detection of some well-known steganalysis techniques.
7 ET13 iM7
TRAFFIC CONGESTION IDENTIFICATION BASED ON IMAGE PROCESSING
DESCRIPTION
This study proposes a novel approach towards traffic congestion identification based on vehicle trajectories in intelligent vehicle infrastructure co-operation system (IVICS). Considering spatial-temporal trajectories as image, this study uses self-correlation to extract propagation speed of congestion wave.
AndroidS.No. CODE PROJECT TITLE
1 ET13AN1
Energy management application for smart grids aiming at mobile device
DESCRIPTION
This paper presents methods for monitoring and controlling the energy consumption, which supported the development of an Android application (for mobile devices) to interact with a Smart Grid Network.Through this application the costumer may visualize its energy consumption data and use this information to support decisions regarding the management, control or adequacy of their consumption habits.
2 ET13AN2
Portable wireless biomedical temperature monitoring system: Architecture and
implementation
DESCRIPTION
This paper demonstrates the design and implementation of a portable embedded system targeting continuous temperature monitoring with wireless interface capability. Our main motive is to provide a solution for monitoring babies', disable or elderly population body temperature and initiate immediate alarm in case of hazardous cases.
3 ET13AN3
Design and implementation of a wireless tensiometer with smartphone interface
DESCRIPTION
The prototype has been developed to allow the final user to keep a register of its own blood pressure measurement. The application also can generate a report with the measurement data that can be sent to a doctor or to an online database historical profile keeping, which may be useful for remote diagnosis procedures.
4 ET13AN4
A Common Interface for Bluetooth-based Health Monitoring Devices
DESCRIPTION
In this project a patient temperature and heart rate are monitored and displayed in an android device. This data’s are sent and received by using a Bluetooth module
5 ET13AN5
Remote Monitoring System of ECG and Human Body Temperature Signals
DESCRIPTION
The paper presents a remote monitoring system for electrocardiographic and temperature signals. The system consists of a hardware module for acquisition, a Bluetooth transmission module and finally a displaying module (PC or mobile devices). Information is sent via IP (GPRS or Wi-Fi) to a database
6 ET13AN6
A Bluetooth toy car control realization by android equipment
DESCRIPTION
A remote toy car controlled by an android mobile platform with Bluetooth technology is presented in this paper. The mobile platform requests to connect with the small car then sends instructions to control it by calling the android system Bluetooth API.
7 ET13AN7
Smart home system for Disabled People via Wireless Bluetooth
DESCRIPTION
in our project work, we attempt to design the smart home system including the wireless controller via Bluetooth technology. This software application adapt in mobile phone, PDA, mobile computer using android's operating system (OS). This software application will control the electrical appliances switches wirelessly (Bluetooth).
8 ET13AN8
Bluetooth-Based Android Interactive Applications for Smart Living
DESCRIPTION
For smart living, interactive applications are increasingly important especially on interaction of people and the environment. In this work, a Bluetooth-based mobile sensor interactive application in Android- designed & implemented.
ARDUINO
S.No. CODE PROJECT TITLE1 ET13A
R1Data acquisition and control using Arduino-
Android platform: Smart plug
DESCRIPTION
In this work, we propose to develop a smart plug, an energy monitoring system that provides real time update of the energy consumption at the device level. The proposed device is using an arduino microcontroller board, an ENC28J60 ethernet module, and a current transformer sensor.
2 ET13AR2
ZigBee wireless sensor network for radiation monitoring at nuclear facilities
DESCRIPTION
This paper describes the design of a WSN that allows smart real time monitoring of radiation levels at nuclear facilities. We develop a local low cost prototype of wireless sensor node equipped with a radiation sensor. The wireless node based on ZigBee technology and Arduino platform.
3 ET13AR3
Development of an educational environment for online control of a biped robot using MATLAB and
Arduino
DESCRIPTION
This paper describes the development of innovative low-cost educational platform to study and control a biped robot in real-time using MATLAB and Arduino board. MATLAB was used as a control and visualization environment, while the Arduino board was utilized as a final controller for the servo motors as well as a Data Acquisition Card (DAC).
4 ET13AR4
Automatic control for laboratory sterilization process based on arduino hardware
DESCRIPTION
This System is based on Arduino Board. Arduino is an Open Hardware platform that allows a fast prototype development, Arduino microcontroller is programmed on C++. making development and tests not a difficult part of overall work.
Top Related