Aspire 5610/TravelMate 4200 SeriesService Guide
PRINTED IN TAIWAN
Service guide files and updates are availableon the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
II
Revision HistoryPlease refer to the table below for the updates made on Aspire 5610/TravelMate 4200 service guide.Date Chapter Updates
CopyrightCopyright 2006 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, tat
DisT
Acppdd
AIPOIII
ransmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in ny form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
he prior written permission of Acer Incorporated.
claimerhe information in this guide is subject to change without notice.
cer Incorporated makes no representations or warranties, either expressed or implied, with respect to the ontents hereof and specifically disclaims any warranties of merchantability or fitness for any particular urpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the rograms prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its ealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential amages resulting from any defect in the software.
cer is a registered trademark of Acer Corporation.ntel is a registered trademark of Intel Corporation.entium and Pentium II/III are trademarks of Intel Corporation.ther brand and product names are trademarks and/or registered trademarks of their respective holders.
IV
ConventionsThe following conventions are used in this manual:SCREEN MESSAGES Denotes actual messages that appear on screen.
NOTE Gives bits and pieces of additional information related to the current topic.
WARNING Alerts you to any damage that might result from doing or not doing specific actions.
CAUTION Gives precautionary measures to avoid possible hardware or software problems.
IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.
PrefaceBefore using this information and the product it supports, please read the following general information.
1
2V
. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details.
. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.
VI
Chap
FeaB
Platf
Disp
Stor
Inpu
Aud
System Specifications
Chapter 1tureselow is a brief summary of the computers many feature:
orm and memroy
T Intel Centrino Duo mobile technology, featuring:
t Intel CoreTM Duo processor T2300/T2400/T2500/T2600 (2 MB L2 cache, 1.66/1.83/2/2.16GHz, 667 MHz FSB)
t Intel 945GM/945PM+ICH7M
T Integrated Intel PRO/Wireless 3945ABG network connection (dual-band tri-mode 802.11a/b/g) Wi-Fi CERTIFIEDTM solution, supporting Acer SignalUpTM wireless technology
T 256/512 MB of DDR2 533/677 MHz memory, upgradeable to 2 GB using two so DIMM modules (dual-channel support )
lay and graphicsT 15.4 WXGA color TFT LCD, 1280 x 800 pixel resolution, supporting simultaneous multi-window
viewing via Acer GridVistaTM
T 15 XGA color TFT LCD, 1024x 768 pixel resolution
T NVIDIA GeForceTM Go 7300 (72MV) graphics with 64/128 MB of dedicated GDDR2 VRAM, supporting NVIDIA TurboCacheTM technology with up to 128 MB of additional dynamically shared system memory, Microsoft DirectX 9.0 and PCI Express
T 16.7 million colors
T Intel 945GM integrated 3D graphics, featuring Intel Graphics Media Accelerator 950 and up to 128 MB of dynamically shared system memory, supporing Microsoft DirectX 9.0 and PCI Expresst
T Dual independent display support
T MPEG-2/DVD hardware-assisted capability
age subsystemT 80/100/120 GB ATA/100 hard disk drive
T Optical drive options:t8X DVD-Super Multi double-layert8X DVD-Dual double-layer
t devicesT 88/89-key keyboard
T Touchpad with 4-way scroll button
T 12 function keys
T Four easy-launch buttons
T Two front-access buttons: WLAN LED-button and Bluetooth LED-button
ioT Audio system with two built-in speakerster 1 1
2T Intel High-Definition audio support
T Sound Blaster ProTM and MS Sound compatible
Com
Pow
I/O P
EnviChapter 1
T S/PDIF (Sony/Philips Digital Interface) support for digital speakers
municationT Modem: 56K ITU V.92 modem with PTT approval; wake-on ring ready
T LAN: gigabit Ethernet; wake-on-LAN ready
T WLAN: integrated Intel PRO/Wireless 3945ABG network connection (dual-band tri-mode 802.11a/b/g) Wi-Fi CERTIFIEDTM solution, supporting Acer SignalUpTM wireless technology
T WPAN: integrated Bluetooth 2.0+EDR
er subsystemT ACPI 1.0b power management standard: supports Standby and Hibernation power-saving modes
T 71 W 8-cell, 59.2W 8-cell or 44 W 6-cell Li-ion battery pack
T 2-hour rapid charge; 2.5-hour charge-in-use
T 90 W AC adapter
ortsT PC Card slot (one Type II)
T Four USB 2.0 ports
T External display (VGA) port
T Headphones/speaker/line-out jack with S/PDIF support
T Microphone/line-in jack
T Ethernet (RJ-45) port
T Modem (RJ-11) port
T DC-in jack for AC adaptor
ronmentT Temperature:
toperating: 5 C to 35 C
tNon-operating: -20 C to 65 C
T Humidity (non-condensing):toperating: 20%~80%
tNon-operating: 20%~80%
Chap
System Block DiagramThis is for UMA models
Tter 1 3
his is for discrete models
Power On/Off CKT.
Touch Pad
page 42
CRT & TV-out
LPC BUS
page 36
uFCBGA-1466
page 22
H_A#(3..31)
CardBus
IDSEL:AD20(PIRQA#,GNT#2,REQ#2)
H_D#(0..63)
page 27
ENE CB714
page 16
MDC 1.5
Conn
page 37
page 29
Int.KBD
page 30
page 33
BANK 0, 1, 2, 3
USB conn x4
533/667MHz
ALC883
DMI
page 24
DC/DC Interface CKT.
Yonah
page 33
3.3V 48MHz
PSB
CDROM
Conn.
RJ45
Clock Generator
ICS9LPRS325
page 32
BCM4401E
EC I/O Buffer
Fan Control
Power Circuit DC/DC
HDD
Conn.
PCI BUS
uPGA-478 Package
IEEE 1394
3.3V 33 MHz
IDSEL:AD17(PIRQF#,GNT#3,REQ#3)
page 35
200pin DDRII-SO-DIMM X2
IDSEL:AD16(PIRQE#,GNT#2,REQ#2)
page 40
Intel 945PM/GM
3.3V ATA-100
page 25
LAN (10/100)
Slot 0
BIOS
page 4
1.8V DDRII 400/533
page 4,5
page 33
HDA Codec
page 14
Memory BUS(DDRII)
BGA-652HD Audio
page 47
page 23
page 6,7,8,9,10,11
Intel ICH7-M
Thermal Sensor
page 12,13
page 18,19,20,21
page 35
page 26
ENE KB910Q
Audio AMP
LCD Conn.
USB port 0, 2
page 34
Bluetooth
Conn
USB port5
3.3V 24.576MHz/48Mhz
page 30
1394 Conn.
Phone Jack x3
IDE
RTC CKT.page 35
page 15
Dual Channel
6 in 1
socketpage 25
page 37
page 40,41,42,43 44,45,46,47
S-ATA
page 22
S-ATA HDD
Conn.
Mini PCI
socket
IDSEL:AD18(PIRQG/H#,GNT#3,REQ#3)
page 28
VT6311S(WLAN)
(TV-Tuner)
page 34
LCM Conn.
page 17
DVI-D Conn.
page 31
Super I/OSMsC LPC47N207
FIR
page 31
F75383M
page 37
Subwoofer
page 34
Switch/B Conn.
page 29
New Card
Socket
USB port 1
PCI Express
page 22
SATA-to-IDE
page 26
MINI CARD x2
USB port 3, 7
port 0 port 0
page 34
CIR
page 17
CH7307C SDVO
LAN(GbE)BCM5789
page 28
USB port4, 6
page 31
TPM1.2SLB9635 TT 1.2
page 34
MEDIA/B Conn.
TFDU6102-TR3
SPIF3811-HV096
LVDSDVI
Power On/Off CKT.
Touch Pad
page 42
CRT & TV-out
LPC BUS
page 44
uFCBGA-1466
page 30
H_A#(3..31)
CardBus
IDSEL:AD20(PIRQA#,GNT#2,REQ#2)
H_D#(0..63)
page 35
nVidia G73M/(72M)/72MV
ENE CB714
page 24
MDC 1.5
Conn
page 45
page 37
Int.KBD
page 38
page 41
PCI-Express
BANK 0, 1, 2, 3
USB conn x4
533/667MHz
ALC883
DMI
page 32
DC/DC Interface CKT.
Yonah
page 41
3.3V 48MHz
PSB
CDROM
Conn.
RJ45
Clock Generator
ICS9LPRS325
page 40
BCM4401E
EC I/O Buffer
Fan Control
Power Circuit DC/DC
HDD
Conn.
PCI BUS
uPGA-478 Package
IEEE 1394
3.3V 33 MHz
IDSEL:AD17(PIRQF#,GNT#3,REQ#3)
page 43
200pin DDRII-SO-DIMM X2
IDSEL:AD16(PIRQE#,GNT#2,REQ#2)
page 48
Intel 945PM/GM
3.3V ATA-100
page 33
LAN (10/100)
Slot 0
BIOS
page 4
1.8V DDRII 400/533
page 4,5
page 41
HDA Codec
page 14
Memory BUS(DDRII)
BGA-652HD Audio
page 47
page 31
page 6,7,8,9,10,11
Intel ICH7-M
Thermal Sensor
page 12,13
page 26,27,28,29
page 43
page 34
ENE KB910Q
Audio AMP
LCD Conn.
with 64/128/256MB VRAM
USB port 0, 2
page 42
Bluetooth
Conn
USB port5
3.3V 24.576MHz/48Mhz
page 38
1394 Conn.
Phone Jack x3
IDE
RTC CKT.page 43
page 23
Dual Channel
6 in 1
socketpage 33
page 45
page 49,50,51,52 53,54,55,56
S-ATA
page 30
S-ATA HDD
Conn.
Mini PCI
socket
IDSEL:AD18(PIRQG/H#,GNT#3,REQ#3)
page 36
VT6311S(WLAN)
(TV-Tuner)
page 42
CD-PLAY/B Conn.
page 25
DVI-D Conn.
page 39
Super I/OSMsC LPC47N207
FIR
page 39
F75383M
page 46
Subwoofer
page 42
Switch/B Conn.
page 15,16,17,18,19,20,21,22 page 37
New Card
Socket
USB port 1
PCI Express
page 30
SATA-to-IDE
page 34
MINI CARD x2
USB port 3, 7
port 0 port 0
page 42
CIR
page 25
CH7307C SDVO
LAN(GbE)BCM5789
page 36
USB port4, 6
page 39
TPM1.2SLB9635 TT 1.2
page 42
MEDIA/B Conn.
TFDU6102-TR3
SPIF3811-HV096
LVDS
LVDSDVI
DVI
4Board Layout
Top
1
2
3
4
5
6
7
8
9Chapter 1
View
JP1 LCD Connector 10 SW7 Touchpad Down Button
SW1 Lid Switch 11 SW2 Touchpad Up Button
JP3 MDC Connector 12 SW5 Touchpad Left Button
JP2 Power Button Connector 13 SW3 Touchapd Left Button
JP6 Media Board Connector 14 JP13 Internal Microphone Connector
JP7 Touchpad Board Connector 15 JP12 Internal Speaker Connector
JP43 SIM Card Connector 16 JP9 PCMCIA Socket
SW4 Touchpad Right Button 17 IR1 FIR Module
SW6 Touchpad Left Button 18 JP8 Internal Keyboard Connector
Chap
Bottom View
N
1
2
3
4
5
6
7
8
9
1
1
1
1
1
1
1ter 1 5
OTE: This is engineering sample. The image above may not be exactly the same as the real main board you get.
JP19 FAN Connector 17 JP40 Headphone/SPDIF Jack
U42 VGA Chipset 18 JP41 Line-In Jack
JP18 CPU Socket 19 JP42 Microphone-in Jack
JP16 DVI Connector 20 IR2 CIR Module
JP15 CRT Connector 21 SW8 Wireless LAN Switch
JP14 TV-Out Connector 22 SW9 Bluetooth and 3G Switch
PCN1 DC-IN Jack 23 U48 South Bridge Chipset
JP17 Mini Card Connector 24 JP30 Mini Card Connector
JP22 DDRII so-DIMM Socket 25 JP29 IEEE 1394 Connector
0 JP21 DDRII so-DIMM Socket 26 JP27 5 IN1 Socket
1 J3 Clear CMOS Jumper 27 JP23 RJ45 Connector
2 JP24 ODD Connector 28 JP5 USB Connector
3 PJP1 Battery Connector 29 JP4 USB Connector
4 JP32 HDD Connector (SATA) 30 JP28 MINIPCI Connector (TV-Tuner)
5 JP33 HDD Connector (PATA) 31 JP25 FAN Connector
6 JP36 Bluetooth Connector 32 U40 North Bridge Chipset
6Jumper Board Layout
Sw
MeChapter 1
itch Board Top View
dia Board Top View
Label Description
SW1 Arcade/TV tunver switch
SW2 Volume Up switch
SW3 Volume Down switch
SW4 Play/Pause switch
SW5 Stop switch
SW6 Forward/Next switch
SW7 Backward/Previous switch
Label Description
SW1 Power Button
SW2 E-mail Button
SW3 Internet Button
SW4 User Button
SW5 E-Power Button
Chap
Media Board Bottom View
LS-2ter 1 7
923P Power Board Top View
Label Description
JP3 USB Connector
JP2 USB Connector
JP6 RF INe Connector
JP5 RF Cable Connector
JP4 AV IN Connector
JP7 Board to Main Board Connector
Label Description
JP1 SIM Card Connector
8Jumper SettingChapter 1
Label Description
J3 Clear CMOS JumperNote: J3 locates at bottom side of the main board as the red circle highlighted.
Chap
Your Acer Notebook tourAfter knowing your computer features, let us show you around your new TravelMate computer.
FroA
1
2
3
4
5
6
7
8
9
1ter 1 9
nt viewspire 5610:
# Item Description
Display screen Also called LCD (liquid-crystal display), displays computer output.
Keyboard For entering data into your computer.
Touchpad Touch-sensitive pointing device which functions like a computer mouse.
Click buttons (left, center and right)
The left and right buttons function like the left and right mouse buttons; the center button serves as a 4-way scroll button.
Palmrest Comfortable support area for our hands when you use the computer.
Microphone Internal microphone for sound recording.
TV/media/volume buttons
For use with Acer Arcade and other media playing programs.
Easy-launch buttons Buttons for launching frequently used programs.
Status indicators Light-Emitting Diodes (LEDs) that light up to show the status of the computers functions and components.
0 Power button Turns the computer on and off.
10
TravelMate 4200:
1
2
3
4
5
6
7
8
9Chapter 1
# Item Description
Display screen Also called LCD (liquid-crystal display), displays computer output.
Keyboard For entering data into your computer.
Touchpad Touch-sensitive pointing device which functions like a computer mouse.
Click buttons (left, center and right)
The left and right buttons function like the left and right mouse buttons; the center button serves as a 4-way scroll button.
Palmrest Comfortable support area for our hands when you use the computer.
Microphone Internal microphone for sound recording.
Easy-launch Buttons Buttons for launching frequently used programs.
Status indicators Light-Emitting Diodes (LEDs) that light up to show the status of the computers functions and components.
Power button Turns the computer on and off.
Chap
Closed Front ViewAspire 5610:
1
2
3
4
5
6
7
8
9
1ter 1 11
# Icon Item Description
Speaker Left and right speakers deliver stereo audio output.
Bluetooth communication button/indicator
Enable/disable Bluetooth function. Indicates the status of Bluetooth-communications.
Wireless communication button/indicator
Enable/disable Wireless function. Indicates the status of wireless LAN communications.
Power indicator Indicates the computers power status.
Battery indicator Indicates the computers battery status.
CIR receiver Receives signals from a remote control.
Microphone-in jack Accepts input from external microphones.
Line-in jack Accepts audio line-in devices (e.g., audio CD player, stereo walkman).
Headphones/speakers/line-out jack with S/PDIF support
Connects to audio line-out devices (e.g., speakers, headphones).
0 Latch Locks and release the lid.
# Icon Item Description
# Icon Item Description
"Easy-launch buttons" on page 18
# Icon Item Description
# Item Description
"Easy-launch buttons" on page 18
# Icon Item Description
# Item Description
12
TravelMate 4200:
LefA
1
2
3
4
5
6
7
8
9Chapter 1
t Viewspire 5610/TravelMate 4200:
# Icon Item Description
Speaker Left and right speakers deliver stereo audio output.
Bluetooth communication button/indicator
Enable/disable Bluetooth function. Indicates the status of Bluetooth-communications.
Wireless communication button/indicator
Enable/disable Wireless function. Indicates the status of wireless LAN communications.
Power indicator Indicates the computers power status.
Battery indicator Indicates the computers battery status.
Microphone-in jack Accepts input from external microphones.
Line-in jack Accepts audio line-in devices (e.g., audio CD player, stereo walkman).
Headphones/speakers/line-out jack with S/PDIF support
Connects to audio line-out devices (e.g., speakers, headphones).
Latch Locks and release the lid.
"Easy-launch buttons" on page 18
# Icon Item Description
# Item Description
"Easy-launch buttons" on page 18
# Icon Item Description
# Item Description
Chap
RigA
1
2
3
4
5
6
1
2
3ter 1 13
ht Viewspire 5610/TravelMate 4200:
# Icon Item Description
Kensington lock slot Connects to a Kensington-compatible computer security lock.
Ventilation slots Enables the computer to stay cool, even after prolonged use.
Two USB 2.0 ports Connects to USB 2.0 devices (e.g., USB mouse, USB camera).
Modem (RJ-11) port Connects to a phone line.
PC Card slot Accepts one Type II PC Card.
PC Card slot eject button
Ejects the PC Card from the slot.
# Icon Item Description
Optical drive Internal optical drive; accepts CDs or DVDs.
Optical disk access indicator
Light up when the optical drive is active.
Optical drive eject button
Ejects the optical disk from the drive.
14
ReaA
BasA
4 Emergency eject hole Ejects the optical drive tray when the comptuer is turned off.Chapter 1
r Panelspire 5610/TravelMate 4200:
e viewspire 5610/TravelMate 4200:
# Icon Item Description
1 Ethernet (RJ-45) port Connects to an Ethernet 10/100/1000-based network (for selected models).
2 Two USB 2.0 ports Connects to USB 2.0 devices (e.g., USB mouse, USB camera).
3 DC-in jack Connects to an AC adapter.
4 External display (VGA) port
Connects to a display device(e.g., external monitor, LCD projector).
5 Ventilation slots Enable the computer to stay cool, even after prolonged use.
Chap
IndTf
A
Tc
# Item Description
1
2
3
4
5
6ter 1 15
icatorshe computer has four easy-to-read status indicators on the upper-right above the keyboard, and four on the
ront panel.
spire 5610/TravelMate 4200:
he power, battery and wireless communication status indicators are visible even when the LCD display is losed.
Battery lock Locks the battery in position.
Battery bay Helps keep the computer cool.Note: Do not cover or obstruct the opening of the fan.
Hard disk bay Houses the computers hard disk (secured with screws)
Acer DASP (Disk Anti-Shock Protection)
Protects the hard disk drive from shocks and bumps. (for TravelMate 4200)
Memory compartment Houses the computers main memory.
Ventilation slots and cooling fan
Release the battery for removal.
Icon Function Description
Cap lock Lights when Cap Lock is activated
Num lock Lights when Num Lock is activated.
HDD Indicates when the hard disc or optical drive is active.
Icon Function Description
16
N
EasL
W
Par
Icon Function DescriptionChapter 1
OTE: 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows green when in AC mode.
y-Launch Buttonsocated above the keyboard are four buttons. These buttons are called easy-launch buttons. They are: mail
eb browser, Empowering Key and one user-programmable button.
ress to run the Acer Empowering Technology. The mail and Web browser buttons are pre-set to email nd Internet programs, but can be reset by users. To set the Web browser, mail and programmable buttons, un the Acer Launch Manager.
Bluetooth Indicates the status of Bluetooth communication.
Wireless LAN Indicates the status of wireless LAN communication.
Battery Lights up when the battery is being charged.
Power Lights up when the computer is on.
Launch key Default application
P User-programmable
P User-programmable
Acer Empowering Technology (user-programmable)
Chap
Launch key Default applicationter 1 17
Web browser Internet browser (user-programmable)
Mail Email application (user-programmable)
18
Using the KeyboardThe keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and t
LocT
A
T
Tla
C
N+
When Scroll Lock is on, the screen moves one line up or down when you press the up or down arrow keys respectively. Scroll Lock does not work with some applications.
Desired Access Num Lock On Num Lock Off
umber keys on embedded eypad
Type numbers in a normal manner.
ursor-control keys on mbedded keypad
Hold while using cursor-control keys.
Hold while using cursor-control keys.
Chap
WinT
HotTb
T
A
T
Main keyboard keys Hold while typing letters on embedded
Type the letters in a normal manner.
W
o
Desired Access Num Lock On Num Lock Offter 1 19
dows Keyshe keyboard has two keys that perform Windows-specific functions.
Keyshe computer employs hotkeys or key combinations to access most of the computers controls like sreen rightness, volume output and the BIOS utility.
o activate hot keys, press and hold the key before pressing the other key in the hotkey combination.spire 5610:
ravelMate 4200:
keypad.
Key Icon Description
indows key Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the Start menu. It can also be used with other keys to provide a variety of function:
+ Activates next taskbar button.
+ Opens the My Computer window
+ Opens Help and Support.
+ Opens the Find: All Files dialog box.
+ Opens the Run dialog box.
+ M Minimizes all windows.
+ + Undoes the minimize all windows action.
Applicatin key
This key has the same effect as clicking the right mouse button; it opens the applications context menu.
20
F
F
F
F
F
F
F
F
F
F
FChapter 1
Hot Key Icon Function Description
n-F1 Hot key help Displays help on hot keys.
n-F2 Acer eSetting Launches the Acer eSettings in Acer eManager.
n-F3 Acer ePowerManagement
Launches the Acer ePowerManagement in Acer eManager.
n-F4 Sleep Puts the computer in Sleep mode.
n-F5 Display toggle Switches display output between the display screen, external monitor (if connected) and both.
n-F6 Screen blank Turns the display screen backlight off to save power. Press any key to return.
n-F7 Touchpad toggle Turns the internal touchpad on and off.
n-F8 Speaker toggle Turns the speakers on and off.
n-w Volume up Increases the speaker volume.
n-y Volume down Decreases the speaker volume.
n-x Brightness up Increases the screen brightness.
Chap
SpeYT
A
T
The 1
2
The 1
2
N
N
Fn-z Brightness down Decreases the screen brightness
Hot Key Icon Function Descriptionter 1 21
cial Keyou can locate the Euro symbol and US dollar sign at the upper-center and/or bottom-right of your keyboard. o type:
spire 5610:
ravelMate 4200:
Euro symbol. Open a text editor or word processor.
. Either directly press the symbol at the bottom-right of the keyboard, or hold and then press the symbol at the upper-center of the keyboard.
US dollar sign. Open a text editor or word processor.
. Either directly press the key at the bottom-right of the keyboard, or hold and then press the key at the upper-center of the keyboard.
OTE: This function varies by the operating system version.
OTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/typography/faq/faq12.htm for more information.
22
Acer Empowering TechnologyAcers innovative Empowering Technology makes it easy for you to access frequently used functions and m
TTT
TTTTT
Fa
AceAuChapter 1
anage your new Acer notebook. It features the following handy utilities:
Acer eDataSecurity Management protects data with passwords and advanced encryption algorithms.Acer eLock Management limits access to external storage media.Acer ePerformance Management improves system performance by optimizing disk space, memory and registry settings.Acer eRecovery Management backs up/recovers data flexibly, reliably and completely.Acer eSettings Management accesses system information and adjusts settings easily.Acer eNet Management hooks up to location-based networks intelligently.Acer ePower Management extends battery power via versatile usage profiles.Acer ePresentation Management connects to a projector and adjusts display settings conveniently.
or more information, press the < > key to launch the Empowering Technology menu, then click on the ppropriate utility and select the Help function.
r eDataSecurity Managementcer eDataSecurity Management is handy file encryption utility that protexts your files from being accessed by nauthorized persons. It is conveniently integrated with Windows explorer as a shell extension for quick and
Chap
easy data encryption/decryption and also supports on-the-fly file encryption for MSN Messager and Microsoft Outlook.
Tsts
Nter 1 23
here are two passwords that can be used to encrypt/decrypt a file; the supervisor passowrd and the file-pecific password. The supervisor passwork is a master password that cna decrypt any file on your system; he file-specific password will be used to encrypt files by default, or you cna choose to enter your own file-pecific password when encrypting a file.
OTE: The password used encrypt a file is the unique key that the system needs to decrypt it. If you lose the password, the supervisor password is the only other key capable of decrypting the file. If you lose both passwords, there will be no way to decrypt your encryped file! Be sure to safeguard all related passwords!
24
AceAd
T
TT
Tta
Ir
NChapter 1
r eLock Managementcer eLock Management is a security utility that allows you to lock up your removable data, optical and floppy rives to ensure that data cant be stolen while your notebook is unattended.
Removable data devices - includes USB disk drives, USB pen drives, USB flash drives, USB MP3 drives, USB memory card readers, IEEE 1394 disk drives and any other removable disk drives that can be mounted as a file system when plugged into the system.Optical drive deivces - includes any kind of CD-ROM or DVD-ROM drives.Floppy disk drives - 3.5-inch disks only.
o activate Acer eLock Management, a password must be set first. Once set, you may apply lock to any of the hree kinds of devices. Lock(s) will immediately be set without any reboot necessary, and will remain locked fter rebooting, until unlocked.
f you do not set a password, Acer eLock Management will reset back to the initial status with all locks emoved.
OTE: If you lose your password, there is no method to reset it except by reformatting your notebook or taking your notebook to anAcer Customer Serivce Center. Be sure to remember or write down your password.
Chap
AceAn
TTTter 1 25
r ePerformance Managementcer ePerformance Management is a system optimization tool that boosts the performance of your Acer otebook. It provides you with the following options to enhance overall system performance:
Memory optimization - releases unused memory and check usage.Disk optimization - removes unneeded items and files.Speed optimization - improves the usability and performance of your Windows XP system.
26
AceAtsw
TTT
TChapter 1
r eRecovery Managementcer eRecovery Management is a powerful utility that does away with the need for recovery disks provided by
he manufacturer. The Acer eRecovery Management utility occupies space in a hidden partition on your ystems HDD. User-created backups are stored on D:\ drive. Acer eRecovery Management provides you ith:
Password protection.Recovery of applications and drivers.Image/data backup:
T Back up to HDD (set recovery point).
T Back up to CD/DVD.Image/data recovery tools:
T Recover from a hidden partition (factory defaults).
T Recover from the HDD (most recent user-defined recovery point).
T Recover from CD/DVD.
Chap
N
AceAsy
A
TTTTTter 1 27
OTE: If your computer did not come with a Recovery CD or System CD, please use Acer eRecovery Managements System backup to optical disk feature to burn a backup image to CD or DVD. To ensure the best results when recovering your system using a CD or Acer eRecovery Management, detach all peripherals (except the external Acer ODD, if your computer has one), including your Acer ezDock.
r eSettings Managementcer eSettings Management allows you to inspect hardware specifications and to monitor the system health tatus. Furthermore, Acer eSettings Management enables you to optimize your Windows operating system, so our computer runs faster, smoother and better.
cer eSettings Management also:
Provides a simple graphical user interface for navigating through the program effortlessly.Displays general system status and advanced monitoring for power users.Logs when a hardware component has been removed or replaced.Permits you to migrate personal settings.Keeps a history log of all alerts that were previously issued.
28
AceAvoa
Af
AaChapter 1
r eNet Managementcer eNet Management helps you to quickly and easily connect to both wired and wireless networks in a ariety of locations. To access this utility, either click on the Acer eNet Management icon on your notebook, r start the program from the Start menu. You also have the option to set Acer eNet Management to start utomatically when you boot up your PC.
cer eNet Management automatically detects the best settings for a new location, while offering you the reedom to manually adjust the settings to match your needs, simply by right-clicking on the icon in the taskbar.
cer eNet Management can save network settings for a location to a profile, and automatically apply the ppropriate profile when you move from one location to another. Settings stored include network connection
Chap
settings(IP and DNS settings, wireless AP details, etc.), as well as default printer settings. Security and safety concerns mean that Acer eNet Management does not store username and password information.
AceAMi
AcerTsC
DC MTM
Crea1
2
3
4
5
BattFwter 1 29
r ePower Managementcer ePower Management features a straightforward user interface. To launch it, select Acer ePower anagement from the Empowering Technology interface, or double-click the Acer ePower Management icon
n the task tray.
Modehe default setting is Maximum Performance. You can adjust CPU speed, LCD brightness and other ettings, or click on buttons to turn the following functions on/off: Wireless LAN, Bluetooth, CardBus, Memory ard, Audio, and Wired LAN.
odeo suit your usage, there are four pre-defined profiles - Entertainment, Presentation, Word Processing, and aximum Battery. Or, you can define up to three of your own profiles.
te new power scheme. Assign a name for the new scheme.
. Choose existing scheme to use as a template.
. Select whether used for mains (AC) or batery mode.
. Choose which power options best fit your needs, then click OK.
. The new profile will appear on the main screen.
ery statusor real-time battery life estimates based on current usage, referto the panel on the lower left-hand side of the indow.
30
Y
TTT
TChapter 1
ou can also click Advanced Settings to:
Set alarms.Re-load factory defaults.Select what actions will be taken when the cover is closed, and set passwords for accessing the system after Hibernation or Standby.View information about Acer ePower Management.
Chap
AcerASter 1 31
ePresentation Managementcer ePresentation Management lets you select from two of the most common projector resolutions: XGA and VGA.
32
Hardware Specifications and Configurations
Processor
B
S
C
C
1
2
C
SChapter 1
Item Specification
CPU type Intel CoreTM Duo processor T2300/T2400/T2500/T2600 (2 MB L2 cache, 1.66/1.83/2/2.16GHz, 667 MHz FSB)
Core logic Intel 945GM/945PM+ICH7-M
CPU package FCBGA-1466
CPU core voltage
IOS
Item Specification
BIOS vendor Phneoix
BIOS Version V1.10
BIOS ROM type 512K Flash ROM
BIOS ROM size 1MB Flash BIOS
BIOS package 32-pin PLCC
Supported protocols ACPI 1.0b/2.0/3.0, PCI2.2, System/HDD Password Security Control, INT 13h Extensions, PnP 1.0a, SMBIOS 2.4, BIOS Boot Specification (Compaq, Phoenix, INtel), Simple Boot Flag 1.0, Boot Block, PCI Bus Power Management Interface Specification,USB 1.1/2.0, PC Card 95, IrDA 1.0, Intel AC97 CNR Specification, WfM 2.0, PXE 2.1, Boot Integrity Service Application Program Interface (BIS) 1.0, PC99a and Mobile PC2001 Compliant, Intel (R) SpeedStep Technology, Legacy 1394 Device support, DMI 2.0, PS/2 keyboard and mouse
BIOS password control Set by setup manual
econd Level Cache
Item Specification
ache controller Built-in CPU
ache size 2MB for Intel Pentium M 945GM/945PM Processor
st level cache control Always enabled
st level cache control Always enabled
ache scheme control Fixed in write-back
ystem Memory
Item Specification
Memory controller Built-in Intel 945GM/945PM
Memory size 0MB (no on-board memory)
DIMM socket number 2 sockets
Supports memory size per socket 1024MB
Supports maximum memory size 2G (by two 1024MB SO-DIMM module)
Supports DIMM type DDR 2 Synchronous DRAM
Supports DIMM Speed 400 MHz
Supports DIMM voltage 1.8V
Supports DIMM package 200-pin soDIMM
Memory module combinations You can install memory modules in any combinations as long as they match the above specifications.
Chap
N
Memory Combinations
L
C
S
L
L
F
M
D
S
M
M
Bter 1 33
OTE: Above table lists some system memory configurations. You may combine DIMMs with various capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be reversed.
Slot 1 Slot 2 Total Memory
0MB 128MB 128MB
0MB 256MB 256MB
0MB 512MB 512MB
0MB 1024MB 1024MB
128MB 128MB 256MB
128MB 256MB 384MB
128MB 512MB 640MB
128MB 1024MB 1152MB
256MB 128MB 384MB
256MB 256MB 512MB
256MB 512MB 768MB
256MB 1024MB 1280MB
512MB 128MB 640MB
512MB 256MB 768MB
512MB 512MB 1024MB
512MB 1024MB 1536MB
1024MB 0MB 1024MB
1024MB 128MB 1152MB
1024MB 256MB 1280MB
1024MB 512MB 1536MB
1024MB 1024MB 2048MB
AN Interface
Item Specification
hipset BroadCom BCM4401E
upports LAN protocol 10/100Mbps
AN connector type RJ45
AN connector location Right side
eatures Integrated 10/100 BASE-T transceiverWake on LAN support compliant with ACPI 2.0PCI v2.2
odem Interface
Item Specification
ata modem data baud rate (bps) 56K
upports modem protocol V.90/V.92
odem connector type RJ11
odem connector location Right side
luetooth Interface
Item Specification
Chipset Built-in Intel ICH7-M
34
W
H
Bluetooth Interface
Item SpecificationChapter 1
Data throughput 723 bps (full speed data rate)
Protocol Bluetooth 2.0
Interface USB 1.1
Connector type Mini-USB
ireless Module 802.11b/g (optional device)
Item Specification
Chipset Built-in ICH7-M
Data throughput 11~54 Mbps
Protocol 802.11b+g
Interface Mini-PCI type II (What does PCI Bus means on the system block diagram?)
ard Disk Drive Interface
Item
Vendor & Model Name
Seagate 40G ST9402112AToshiba MK4025GAS Hitachi HTS421240H9AT00WD WD400UE-22HCT0Samsung M40MP0402H
Seagate ST96812ASeagate ST960821AToshiba MK6025GASHGST HTS541260H9AT00WD WD600UE-22HCT0
TOSHIBA MK8025GAS HITACHI HTS421280H9AT00SEAGATE ST9808210ASEAGATE ST98823ATOSHIBA MK8026GAXHGST HTS541280H9AT00WD WD800UE-22HCT0
Capacity (MB) 40000 60000 80000
Bytes per sector
512 512 512
Data heads 2 3 (for Hitachi and Seagate)4 (for Toshiba)
4 (for Hitachi)3 (for Seagate)
Drive Format
Disks 1 2 2
Spindle speed (RPM)
4200 RPM 4200 RPM 4200 RPM
Performance Specifications
Buffer size 2048KB 8192KB 8192KB
Interface ATA/ATAPI-6; ATA-6 ATA/ATAPI-6; ATA-6 ATA/ATA-6; ATA-6
Max. media transfer rate (disk-buffer, Mbytes/s)
372 350 350
Data transfer rate (host~buffer, Mbytes/s)
100 MB/Sec.Ultra DMA mode-5
100 MB/Sec.Ultra DMA mode-5
100 MB/Sec.Ultra DMA mode-5
DC Power Requirements
Voltage tolerance
5V(DC) +/- 5% 5V(DC) +/- 5% 5V(DC) +/- 5%
Chap
Combo Drive Interface
V
P
T
B
I
A
L
P
I
D
V
P
T
B
I
A
L
P
I
Hter 1 35
Item Specification
endor & model name DVD/CDRW HLDS GCC-4244N
erformance Specification With CD Diskette With DVD Diskette
ransfer rate (KB/sec) Sustained:Max 3.6Mbytes/sec
Sustained:Max 10.8Mbytes/sec
uffer Memory 2MB
nterface Enhanced IDE(ATAPI) compatible
pplicable disc format DVD: DVD-ROM, (DVD-5, DVD-9, DVD-10, DVD-18),DVD-R (read, single border), DVD-RW, DVD-RAM (2.6GB, 4.7GB)CD: CD-DA, CD-ROM, CD-ROM XA, CD-R, CD-RW Photo (Multisession) Video CD, CD-Extra, (CD+), CD-test
oading mechanism Load: ManualRelease: (a) Electrical Release (Release Button) (b) Release by ATAPI command (c) Emergency Release
ower Requirement
nput Voltage 5 V +/- 5 % (Operating)
VD-Dual Interface
Item Specification
endor & model name LITEON SOSW-833SPIONEER DVR-K16RA
erformance Specification With CD Diskette With DVD Diskette
ransfer rate (KB/sec) Sustained:Max 3.6Mbytes/sec
Sustained:Max 10.8Mbytes/sec
uffer Memory 2MB
nterface Enhanced IDE(ATAPI) compatible
pplicable disc format Support disc formats1. Reads data in each CD-ROM, CD-ROM XA, CD-1, Video CD, CD-Extra and CD-Text2. Reads data in Photo CD (single and Multi-session)3. Reads standard CD-DA4. Reads and writes CD-R discs5. Reads and writes CD-RW discs6. Reads and writes in each dVD+R/RW (Ver. 1.1)7. Reads data in each DVD-ROM and DVD-R (Ver. 2.0 for Authoring)8. Reads and writes in each DVD-R (Ver. 2.0 for general), DVD-RW and DVD+R/RW (Ver1.1)
oading mechanism Load: ManualRelease: (a) Electrical Release (Release Button) (b) Release by ATAPI command (c) Emergency Release
ower Requirement
nput Voltage 5 V +/- 5 % (Operating)
D Audio Interface
Item Specification
Audio Controller ALC883
36
N
V
V
U
C
U
O
HD Audio Interface
Item SpecificationChapter 1
OTE: RAMDAC refers to Random Access Memory Digital to Analog Converter: the VGA controller chip that maintains the range of colors and converts data from memory into analog signals for the monitor.
Audio onboard or optional Built-in
Mono or Stereo Stereo
Resolution Wide range (V80dB ~ +42dB) volume control with 1.5dB resolution of analog to analog mixer gain 16 bit stereo digital to analog converter16 bit stereo analog to digital converter
Compatibility HD Audio
Mixed sound source Line-in, CD
Voice channel 8/16-bit, mono/stereo
Sampling rate All DACs support 44.1k/48k/96k/192kHz sample rate All ADCs support 44.1k/48k/96kHz sample rate 16/20/24-bit S/PDIF-OUT supports 44.1k/48k/96k/192kHz sample rate 16/20/24-bit S/PDIF-IN supports 44.1k/48k/96kHz sample rate
Internal microphone Yes
Internal speaker / Quantity Yes/2
ideo Interface
Item Specification
Chipset Built-in Intel 945GM for UMA models
NVIDIA GeForceTM Go 7300 (72MV) for discrete models
Package 35.5 mm x 40 mm 1257 pin mBGA
Interface internal PCIE
Supports ZV (Zoomed Video) port Yes
Memory Interface 64-bit
Memory Bandwidth(GB/sec) 5.6
Fill Rate (Gpixels/sec) 1.4
Vertices/Second (Millions) 260
Memory Data Rate (MHz) 700
RAMDACs (MHz) 400
ideo Memory
Item Specification
Chipset Built-in Intel 945GM for UMA models
NVIDIA GeForceTM Go 7300 (72MV) for discrete models
Memory size 64MB/128MB
Interface DDR2
SB Port
Item Specification
hipset Built-in ICH7-M
SB Compliancy Level 2.0
HCI USB 1.1 and USB 2.0 Host controller
Chap
N
L
S
P
S
K
B
USB Port
Item Specificationter 1 37
umber of USB port 3
ocation Three on the right side
erial port function control Enable/Disable by BIOS Setup
CMCIA Port
Item Specification
PCMCIA controller ENE CB714
Supports card type Type-II
Number of slots One type-II
Access location Left panel
Supports ZV (Zoomed Video) port No ZV support
Supports 32 bit CardBus Yes
ystem Board Major Chips
Item Controller
Core logic Intel 945GM?945PM+ICH7-M
VGA Built in Intel945GM for UMA models
NVIDIA GeForceTM Go 7300 (72MV) for discrete models
LAN ENE BCM4401E
USB 2.0 Built in ICH7-M
Super I/O controller SMsC LPC47N207
MODEM Built-in ICH7-M
Bluetooth Built-in ICH7-M
Wireless 802.11 b+g Built-in ICH7-M
PCMCIA ENE CB714
HD Audio Realtek ALC883
eyboard
Item Specification
Keyboard controller ENE KB 910Q
Total number of keypads 88-/89-key
Windows logo key Yes
Internal & external keyboard work simultaneously
Plug USB keyboard to the USB port directly: Yes
attery
Item Specification
Vendor & model name Sanyo (6cell) 2.0Sony (6cell) 2.0Panasonic (6cell) 2.0Snayo (6cell) 2.4Sony (6cell) 2.4Panasonic (6cell)2.4Sanyo (9cell) 2.4
38
L
Battery
Item SpecificationChapter 1
Battery Type Li-ion
Pack capacity 4000 mAH forSanyo (6cell) 2.03920 mAH Sony (6cell) 2.03900 mAH Panasonic (6cell) 2.04800 mAH Snayo (6cell) 2.44800 mAH Sony (6cell) 2.44800 mAH Panasonic (6cell)2.4Sanyo (9cell) 2.4
Number of battery cell 6/9
Package configuration 3 cells in series, 2 series in parallel3 cells in series, 3 series in parallel
Normal voltage 14.8V
Charge voltage 16.8+-0.2v
CD 14.1 inch
Item Specification
Vendor & model name AU B141EW01 CMO N141I1-L02
QDI QD14TL01-03
SAMSUNG LTN141W1-L01
Screen Diagonal (mm) 14.1 inches 14.1 inches 14.1 inches 14.1 inches
Active Area (mm) 304.1x228.1 304.1x228.1 304.1x228.1
Display resolution (pixels) 1024x768 XGA 1024x768 XGA 1024x768 XGA
Pixel Pitch 0.297x0.297 0.099x0.297 0.297x0.297
Pixel Arrangement R.G.B. Vertical Stripe
R.G.B. Vertical Stripe
R.G.B. Vertical Stripe
Display Mode Normally White Normally White Normally White
Typical White Luminance (cd/m2)also called Brightness
180 (5 point average)150 (5 point average)
160 150
Luminance Uniformity N/A N/A 70
Contrast Ratio 300 300 250
Response Time (Optical Rise Time/Fall Time)msec
24/1115/35
8/17 10/25
Nominal Input Voltage VDD +3.3V Typ. +3.3V 3.3V
Typical Power Consumption (watt) 5.6/5.7 3.96 N/A
Weight 550 570 600
Physical Size(mm) 317.3x242.0x6.0
317.3x242.0x5.9
317.3x242.0x6.5
Electrical Interface 1 channel LVDS 1 channel LVDS 1 channel LVDS
Support Color 262K colors (RGB 6-bit data driver)
262,144 262,144
Viewing Angle (degree)Horizontal: Right/LeftVertial: Upper/Lower
40/4010/30
45/4515/35
40/4020/40
Temperature Range( C)
OperatingStorage (shipping)
0 to +50-20 to +60
0 to +50-25 to +60
0 to +50-20 to +60
Chap
LCD Inverter
A
Ster 1 39
Item Specification
Vendor & model name Darfon/V189-301GP
Brightness conditions N/A
Input voltage (V) 9~21
Input current (mA) 2.56 (max)
Output voltage (V, rms) 780V (2000V for kick off)
Output current (mA, rms) 6.5 (max)
Output voltage frequency (k Hz) 65K Hz (max)
C Adaptor
Item Specification
Input rating 90V AC to 264V AC, 47Hz to 63Hz
Maximum input AC current 1.7A
Inrush current 220A@115VAC220A@230VAC
Efficiency 82% min. @115VAC input full load
ystem Power Management
ACPI mode Power Management
Mech. Off (G3) All devices in the system are turned off completely.
Soft Off (G2/S5) OS initiated shutdown. All devices in the system are turned off completely.
Working (G0/S0) Individual devices such as the CPU and hard disc may be power managed in this state.
Suspend to RAM (S3) CPU set power downVGA SuspendPCMCIA SuspendAudio Power DownHard Disk Power DownCD-ROM Power DownSuper I/O Low Power mode
Save to Disk (S4) Also called Hibernation Mode. System saves all system states and data onto the disc prior to power off the whole system.
40 Chapter 1
Chap
BIOTO
YyT
To
Pb
Pe
F
E
System Utilities
Chapter 2S Setup Utilityhe BIOS Setup Utility is a hardware configuration program built into your computers BIOS (Basic Input/utput System).
our computer is already properly configured and optimized, and you do not need to run this utility. However, if ou encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 roubleshooting when problem arises.
o activate the BIOS Utility, press m during POST (when Press to enter Setup message is prompted n the bottom of screen).
ress m to enter setup. The default parameter of F12 Boot Menu is set to disabled. If you want to change oot device without entering BIOS Setup Utility, please set the parameter to enabled.
ress during POST to enter multi-boot menu. In this menu, user can change boot device without ntering BIOS SETUP Utility.
PhoenixBIOS Setup Utility
CPU Type : Genunie Intel (R) CPU
CPU Speed :
BIOS Version: V1.10
VGA BIOS Ver Intel V1256
Serial Number xxxxxxxxxxxxxxxxxxxxxx
Asset Tag Number
N/A
Produce Name
TravelMate 4200
Manufacturer Name:
Acer
UUID:
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
1 Help Select Item F5/F6 Change Values F9 Setup Defaults
sc Exit Select Menu Enter Select 4Sub-Menu F10 Save and Exit
HDD Model Name :
HDD Serial Number :
22 Byte
32 Byte
16 Byte
16 Byte
32 Byte
1.66GHz
ATAPI Serial Number : None
ATAPI Model Name : None
Main Advanced Security Boot ExitInformationter 2 37
38
Navigating the BIOS UtilityThere are six menu options: Info., Main, System Devices, Security, Boot, and Exit.
F
NChapter 2
ollow these instructions:
T To choose a menu, use the cursor left/right keys (zx).
T To choose a parameter, use the cursor up/down keys ( wy).
T To change the value of a parameter, press por q.
T A plus sign (+) indicates the item has sub-items. Press e to expand this item.
T Press ^ while you are in any of the menu options to go to the Exit menu.
T In any menu, you can load default settings by pressing t. You can also press u to save any changes made and exit the BIOS Setup Utility.
OTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a particular menu are shown on the bottom of the screen. Help for parameters are found in the Item Specific Help part of the screen. Read this carefully when making changes to parameter values. Please note that system information is subject to different models.
Chap
Information
N
C
I
I
I
I
S
V
K
S
A
P
M
U
F
Eter 2 39
OTE: The system information is subject to different models.
Parameter Description
PU Type This field shows the CPU type and speed of the system.
DE1 Model Name This field shows the model name of HDD installed on primary IDE master.
DE1 Serial Number This field displays the serial number of HDD installed on primary IDE master.
DE2I Model Name This field displays the mofel name of devices installed on secondary IDE master. The hard disk drive or optical drive model name is automatically detected by the system.
DE2 Serial Number This field shows the serial number of devices installed on secondary IDE master.
ystem BIOS ver Displays system BIOS version.
GA BIOS Ver This field displays the VGA firmware version of the system.
BC Ver This field shows the keyboard
erial Number This field displays the serial number of this unit.
sset Tag Number This field displays the asset tag number of the system.
roduct Name This field shows product name of the system.
anufacturer Name This field displays the manufacturer of this system.
UID Number This will be visible only when an internal LAN device is presenting.UUID=32bytes
PhoenixBIOS Setup Utility
CPU Type : Genunie Intel (R) CPU
CPU Speed :
BIOS Version: V1.10
VGA BIOS Ver Intel V1256
Serial Number xxxxxxxxxxxxxxxxxxxxxx
Asset Tag Number
N/A
Produce Name
TravelMate 4200
Manufacturer Name:
Acer
UUID:
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
1 Help Select Item F5/F6 Change Values F9 Setup Defaults
sc Exit Select Menu Enter Select 4Sub-Menu F10 Save and Exit
HDD Model Name :
HDD Serial Number :
22 Byte
32 Byte
16 Byte
16 Byte
32 Byte
1.66GHz
ATAPI Serial Number : None
ATAPI Model Name : None
Main Advanced Security Boot ExitInformation
40
MainThe Main screen displays a summary of your computer hardware information, and also includes basic setup p
N
F
EChapter 2
arameters. It allows the user to specify standard IBM PC AT system parameters.
OTE: The screen above is for your reference only. Actual values may differ.
PhoenixBIOS Setup Utility
Information Main Advanced Security Boot Exit
Item Specific Help
System Time: [22:03:28]
System Date: [12/21/2005]
System Memory: 640 KB
Extended Memory: 255 MB
Video Memory [64MB]
Quiet Boot: [Enabled]
Power on display: [Auto ]
Network boot [Enabled]
F12 Boot Menu
[Disabled]
, , or
selects field.
1 Help Select Item F5/F6 Change Values F9 Setup Defaults
sc Exit Select Menu Enter Select 4Sub-Menu F10 Save and Exit
Shows system base memory size
Shows extended memory size
VGA memory size
D2D Recovery [Enabled]
Chap
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings.
N
S
S
S
E
V
Q
P
N
F
Dter 2 41
OTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is because the user is not allowed to control the settings in these cases.
Parameter Description Format/Option
ystem Time Sets the system time. The hours are displayed with 24-hour format.
Format: HH:MM:SS (hour:minute:second) System Time
ystem Date Sets the system date. Format MM/DD/YYYY (month/day/year)System Date
ystem Memory This field reports the memory size of the system. Memory size is fixed to 640MB
xtended Memory This field reports the memory size of the extended memory in the system. Extended Memory size=Total memory size-1MB
GA Memory Shows the VGA memory size. VGA Memory size=64/128MB
uiet Boot Determines if Customer Logo will be displayed or not; shows Summary Screen is disabled or enabled. Enabled: Customer Logo is displayed, and Summary Screen is disabled.Disabled: Customer Logo is not displayed, and Summary Screen is enabled.
Option: Enabled or Disabled
ower on display Auto: During power process, the system will detect if any display device is connected on external video port. If any external display device is connected, the power on display will be in CRT (or projector) only mode. Otherwise it will be in LCD only mode.Both: Simultaneously enable both the integrated LCD screen and the systems external video port (for an external CRT or projector).
Option: Auto or Both
etwork Boot Enables, disables the system boot from LAN (remote server).
Option: Enabled or Disabled
12 Boot Menu Enables, disables Boot Menu during POST. Option: Disabled or Enabled2D Recovery Enables, disables D2D Recovery function. The
function allows the user to create a hidden partition on hard disc drive to store operation system and restore the system to factory defaults.
Option: Enabled or Disabled
42
AdvancedThe Advanced screen contains parameters involving your hardware devices. It also provides advanced
T
F
EChapter 2
settings of the system.
he table below describes the parameters in the screen. Settings in boldface are the default and suggested
parameter settings.
Description OptionInfrared Port Configure serial port B using options:
[Disabled]: No configuration[Enabled]: User configuration[Auto]: BIOS or OS chooses configuration(OS Controlled) Displayedd when controlled by OS
DisabledEnabledAuto
PhoenixBIOS Setup Utility
Information Main Advanced Security Boot Exit
Item Specific Help
Infrared Port (FIR)
Configure Infrared Port
using options:
[Disable]
No configuration
[Enabled]
User configuration
1 Help Select Item F5/F6 Change Values F9 Setup Defaults
sc Exit Select Menu Enter Select 4 Sub-Menu F10 Save and Exit
[Enabled]
Chap
SecurityThe Security screen contains parameters that help safeguard and protect your computer from unauthorized u
F
Eter 2 43
se.
PhoenixBIOS Setup Utility
Information Main Advanced Boot
Item Specific Help
Supervisor Password Is : Clear
User Password Is :
HDD Password Is:
Clear
Clear
Set Supervisor Password
Set User Password
Set Hdd Password
Password on Boot [Disabled]
Supervisor Password
controls accesses of the
whole setup utility.
It can be used to
boot up when Password
on boot is enabled.
1 Help Select Item F5/F6 Change Values F9 Setup Defaults
sc Exit Select Menu Enter Select 4 Sub-Menu F10 Save and Exit
[Enter]
[Enter]
[Enter]
ExitSecurity
44
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings.
N
SetF
1
2
I
3
4
5
RemFChapter 2
OTE: When you are prompted to enter a password, you have three tries before the system halts. Dont forget your password. If you forget your password, you may have to return your notebook computer to your dealer to reset it.
ting a Passwordollow these steps as you set the user or the supervisor password:
. Use the w andy keys to highlight the Set Supervisor Password parameter and press the e key. The Set Supervisor Password box appears:
. Type a password in the Enter New Password field. The password length can not exceeds 8 alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the Confirm New Password field.
MPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
. Press e. After setting the password, the computer sets the User Password parameter to Set.. If desired, you can opt to enable the Password on boot parameter.
. When you are done, press u to save the changes and exit the BIOS Setup Utility.
oving a Passwordollow these steps:
Parameter Description Option
User Password is Shows the setting of the user password. Clear or SetSupervisor Password is Shows the setting of the Supervisor password Clear or SetSet User Password Press Enter to set the user password. When
user password is set, this password protects the BIOS Setup Utility from unauthorized access. The user can enter Setup menu only and does not have right to change the value of parameters.
Set Supervisor Password Press Enter to set the supervisor password. When set, this password protects the BIOS Setup Utility from unauthorized access. The user can not either enter the Setup menu nor change the value of parameters.
Primary HardDisk Security Enables or disables primary hard disk security function.
Password on Boot Defines whether a password is required or not while the events defined in this group happened. The following sub-options are all requires the Supervisor password for changes and should be grayed out if the user password was used to enter setup.
Disabled or Enabled
Chap
1. Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set Password box appears:
2
3
4
Cha1
2
3
4
5
6
I
T
ISter 2 45
. Type the current password in the Enter Current Password field and press e.
. Press e twice without typing anything in the Enter New Password and Confirm New Password fields. The computer then sets the Supervisor Password parameter to Clear.
. When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
nging a Password. Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Password box appears:
. Type the current password in the Enter Current Password field and press e.
. Type a password in the Enter New Password field. Retype the password in the Confirm New Password field.
. Press e. After setting the password, the computer sets the User Password parameter to Set.
. If desired, you can enable the Password on boot parameter.
. When you are done, press u to save the changes and exit the BIOS Setup Utility.
f the verification is OK, the screen will display as following.
he password setting is complete after the user presses u.
f the current password entered does not match the actual current password, the screen will show you the etup Warning.
46
ImChapter 2
f the new password and confirm new password strings do not match, the screen will display the following essage.
Chap
BootThis menu allows the user to decide the order of boot devices to load the operating system. Bootable devices i
F
Eter 2 47
ncludes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
PhoenixBIOS Setup Utility
Information Main Advanced Security Exit
Item Specific Help
Use or to select a device
devices, then press to
move it up the list, or to
move it down the list. Press
to escape the menu.
1 Help Select Item F5/F6 Change Values F9 Setup Defaults
sc Exit Select Menu Enter Select 4 Sub-Menu F10 Save and Exit
Boot
Boot priority order:
1: IDE 0: TOSHIBA MK6025GAS-(PM)
2: IDE 1: MATSHITADVD-RAM UJ-845S
3: IDE 2:
4: USB FDD:
5: PCI LAN: Broadcom MBA
6: USB HDD:
7: USB KEY:
8: USB CDROM:
48
ExitThe Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
T
E
E
L
D
S
F
EChapter 2
he table below describes the parameters in this screen.
Parameter Description
xit Saving Changes Exit System Setup and save your changes to CMOS.
xit Discarding Changes Exit utility without saving setup data to CMOS.
oad Setup Default Load default values for all SETUP item.
iscard Changes Load previous values from CMOS for all SETUP items.
ave Changes Save Setup Data to CMOS.
PhoenixBIOS Setup Utility
Information Main Advanced Security Boot
Item Specific Help
Exit Saving Changes
Exit Disarding Changes
Load Setup Defaults
Exit System Setup and save
your changes to CMOS.
1 Help Select Item F5/F6 Change Values F9 Setup Defaults
sc Exit Select Menu Enter Select 4 Sub-Menu F10 Save and Exit
Discard Changes
Exit
Save Changes
Chap
BIOS Flash UtilityThe BIOS flash memory update is required for the following conditions:
U
N
N
N
F
F
1
2
3
A
1
2
3ter 2 49
T New versions of system programs
T New features or options
T Restore a BIOS when it becomes corrupted.
se the Phlash utility to update the system BIOS flash ROM.
OTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery Diskette before you use the Phlash utility.
OTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
OTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not completely loaded.
ellow the steps below to run the Phlash:
irst, you have to create a crisis diskette. Follow the steps to create a crisis diskette.
. Insert a floppy disk to the notebook under Windows mode.
. Execute wincris.exe
. Wait for few minutes. The process will completed automatically.
fter you have created crisis diskette, you can then recovery the fail system.
. Insert the Crisis diskette to the computer.
. Press Fn+Esc and power on the sytem.
. The systme will execute the file automatically. Wait for few minutes the system will reboot as the entire process completed.
50 Chapter 2
Chap
Tm
T
N
Chapter 3
Machine Disassembly and Replacementhis chapter contains step-by-step procedures on how to disassemble the notebook computer for aintenance and troubleshooting.
o disassemble the computer, you need the following tools:
T Wrist grounding strap and conductive mat for preventing electrostatic discharge
T Small Philips screw driver
T Philips screwdriver
T Plastic flat head screw driver
T TweezersOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components. When you remove the stripe cover, please be careful not to scrape the cover.ter 3 51
52
General Information
BefB
1
2
3Chapter 3
ore You Beginefore proceeding with the disassembly procedure, make sure that you do the following:
. Turn off the power to the system and all peripherals.
. Unplug the AC adapter and all power and signal cables from the system.
. Remove the battery pack.
Chap
Disassembly Procedure FlowchartThe flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence art
Syter 3 53
nd instructs you on the components that need to be removed during servicing. For example, if you want to emove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in hat order.
Start
ThermalDoor HDD Door
LCD Module
Middle Cover
HDD Bracket
Keyboard
Battery Pack
F*2D*5F*1
B*4
C*2 LCD hinges to logicD*2 LCD hinges to logic
C*2 on bottom side
C*8 upper case assembly to lower case assembly on bottom sideC*2 upper case assembly to lower case assembly on upper side
Lower CaseAssembly
ModemBoard
Switch Board(for ASmodels)
Upper CaseAssembly
Main Board
H*4
Speaker Set
ODD Module
ThermalModule
Lower Case
F*2F*1
F*2
F*1
stem Fan Memory
CPU
B*1D*1
HDD
F*1
F*2
Media Board(for ASmodels)
TouchpadBracket
F*1
Touchpad TouchpadFFC
Mimi Cover
F*1
54
SChapter 3
crew ListItem Description Part Number
A SCREW M2.5*3(NL) 86.TAVV5.001
B SCREW M2.5*6(NL) 86.TAVV5.002
C SCREW M2.5*10(NL) 86.TAVV5.003
D SCREW M2.5*15(NL) 86.TAVV5.004
E SCREW M2*2.2 86.TAVV5.005
F SCREW M2*3(NL) 86.TAVV5.006
G SCREW M2*4 86.TAVV5.007
H SCREW M3*4(NL) 86.TAVV5.008
I SCREW D-SUB 4#X40* 1/5-NI (NL) 86.TAVV5.009
LCD Module
LCD Inverter
LCD Panel
WirelessAntenna Set
LCD Bezel
G*1 for 15"G*2 for 15.4"
B*4
B*2
G*2 for 15.4"
F*8 (4 on left; 4 on right)
LCDAssembly
LCD Cable LCD BracketSets
LCD
Chap
Removing the Battery Pack1. Slide the battery latch then remove the battery.
ter 3 55
56
Removing the HDD Module/Memory/System Fan/Thermal Module/CPU/ODD Module and LCD Module
Rem1
2
3
4
Rem1
2
3
4
5Chapter 3
oving the HDD Module. Remove the two screws fastening the HDD door.
. Detach the HDD door from the notebook.
. Pull the HDD module outwards to disconnect the HDD module from the main board.
. Take out the HDD module carefully.
oving the Memory/System Fan/Thermal Module/CPU. Remove the six screws fastening the thermal door. (M2.5*15(NL) for red circle; M2*3(NL) for yellow circle)
. Detach the thermal door from the notebook.
. Pop out the memory then remove it
. Use a tweezer to take out the fan cable as shown.
. Disconnect the fan cable from the main board.
Chap
6
7
8
9
1
1
1
1ter 3 57
. Remove the two screws fastening the system fan.
. Take out the system fan from the main unit.
. Remove the four screws fastening the thermal module.
. Then detach the thermal module carefully.
0. Use a flat-headed screwdriver to release the CPU lock (Turn anti-clockwise).
1. Detach the CPU from the CPU socket carefully.
2. Tear off the tape fastening the antenna set.
3. Then remove the antenna protection cover.
58
1
1
Rem1
2
Rem1
2
3
4Chapter 3
4. Remove the screw holding the mini cover.
5. Detach the mini cover from the main unit.
oving the ODD Module. First, remove the screw fastening the ODD module as shown.
. Push the ODD module outwards then remove it.
oving the LCD Module. Open the LCD module as shown (See the left and the middle picture).
. Detach the middle cover from the main unit carefully.
. Remove the screw fastening the keyboard.
. Then turn over the keyboard as shown.
Chap
5. Disconnect the keyboard cable from the main board.
6
7
8
9ter 3 59
. Turn over the notebook, remove two screws fastening the LCD module on the bottom.
. Then turn the notebook to the front side. Take out the antenna then disconnect the LCD cable (See the middle and the right images).
. Remove four screws fastening the LCD module (M2.5*10(NL) for yellow circles; M2.5*15(NL) for red circles).
. Then detach the entire LCD module from the main unit carefully.
60
Disassembling the Main Unit
Sep1
2
3
4
5
Disa6
7
8
N
9
1
1Chapter 3
arate the Main Unit Into the Upper and the Lower Case Assembly. Remove two screws fastening the upper case assembly to the lower case assembly.
. Disconnect the LED board cable from the main board.
. Disconnect the touchpad cable from the main board.
. Remove eight screws fastening the upper case assembly and the lower case assembly on the bottom as shown.
. Detach the upper case assembly carefully.
ssembling the Upper Case Assembly. Remove the two screws fastening the media board.
. Take out the media board cable from the lower case as shown.
. Detach the media board from the upper case carefully.
OTE: Only Aspire 5650 series have media board.
. Tear off the mylar on top of the touchpad bracket.
0. Remove the screws holding the touchpad bracket.
1. Then detach the touchpad bracket from the uppwer case.
Chap
1
1
1
Disa1
2
3
4
5
6ter 3 61
2. Disconnect the touchpad FFC.
3. Then remove the touchpad FFC from the touchpad.
4. Detach the touchpad from the upper case.
ssembling the Lower Case Assembly. Detach the switch board from the main board.
. Remove the screw fastening the modem board.
. Disconnect the modem board from the main board then detach the modem board.
. Detach the modem cable from the lower case.
. Disconnect the speaker cable from the main board.
. Then disconnect the microphone cable from the main baord.
62
7. Remove the screw fastening the main board to the lower case.
8
9
1
1Chapter 3
. Pull the lower case outwards as the image shows and detach the main board from the lower case carefully.
. Take out the microphone from the lower case.
0. Remove the two screws fastening the speaker set.
1. Take out the speaker from the lower case.
Chap
Disassembling the LCD Module1. Remove the four screw caps as shown.
2
3
4
5
6
7
8
9
1
1ter 3 63
. Remove the four screws holding the LCD bezel.
. Then detach the LCD bezel from the LCD module.
. Remove the screw fastening the LCD inverter.
. Take out the LCD inverter from the LCD cover, then disconnect the LCD cable from the inverter.
. Disconnect the LCD power cable on the other side.
. Remove the two screws fastening the LCD assembly.
. Take out the LCD assembly from the LCD panel.
. Tear off the tape fastening the LCD cable.
0. Remove the four screws fastening the LCD right bracket.
1. Remove the LCD right bracket.
64
1
1Chapter 3
2. Remove the four screws holding the LCD left bracket.
3. Remove the LCD left bracket.
Chap
Disassembling the External Modules
Disa1
2
3
Disa1
2ter 3 65
ssembling the HDD Module. Remove two screws hodling the HDD bracket on one side.
. Remove another two screws fastening the HDD bracket on the other side.
. Detach the HDD from the HDD bracket.
ssembling the ODD Module. Remove the three screws holding the optical bracket.
. Remove the optical bracket from the optical disk drive.
66 Chapter 3
Chap
U
N
1
2
3
Po
Pc
Po
Oo
Sp
Troubleshooting
Chapter 4se the following procedure as a guide for computer problems.
OTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses.
. Obtain the failing symptoms in as much detail as possible.
. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation.
. Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified) Go To
ower failure. (The power indicator does not go n or stay on.)
Power System Check on page 69.
OST does not complete. No beep or error odes are indicated.
Power-On Self-Test (POST) Error Message on page 72Undetermined Problems on page 84
OST detects an error and displayed messages n screen.
Error Message List on page 73
ther symptoms (i.e. LCD display problems or thers).
Power-On Self-Test (POST) Error Message on page 72
ymptoms cannot be re-created (intermittent roblems).
Use the customer-reported symptoms and go to Power-On Self-Test (POST) Error Message on page 72Intermittent Problems on page 83Undetermined Problems on page 84ter 4 67
68
System Check Procedures
ExtDr
N
D
1
2
3
I
I
1
2
3
ExtDn
D
1
2
3
I
1
2
3
KeR
Ie
I
In
1
2
3
TChapter 4
ernal Diskette Drive Checko the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is
equired.
OTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause damage to the drive or cause the drive to fail.
o the following to select the test device.
. Boot from the diagnostics diskette and start the diagnostics program.
. See if FDD Test is passed as the program runs to FDD Test.
. Follow the instructions in the message window.
f an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
f the error still remains:
. Reconnect the external diskette drive/DVD-ROM module.
. Replace the external diskette drive/CD-ROM module.
. Replace the main board.
ernal CD-ROM Drive Checko the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does ot have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
o the following to select the test device:
. Boot from the diagnostics diskette and start the diagnostics program.
. See if CD-ROM Test is passed when the program runs to CD-ROM Test.
. Follow the instructions in the message window.
f an error occurs, reconnect the connector on the System board. If the error still remains:
. Reconnect the external diskette drive/CD-ROM module.
. Replace the external diskette drive/CD-ROM module.
. Replace the main board.
yboard or Auxiliary Input Device Checkemove the external keyboard if the internal keyboard is to be tested.
f the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable xtending from the keyboard is correctly seated in the connector on the system board.
f the keyboard cable connection is correct, run the Keyboard Test.
f the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a on-defective FRU:
. Reconnect the keyboard cables.
. Replace the keyboard.
. Replace the main board.
he following auxiliary input devices are supported by this computer:
T Numeric keypad
T External keyboard
Chap
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
MeM
1
2
3
4N
PowT
1
2
3
Iter 4 69
mory checkemory errors might stop system operations, show error messages on the screen, or hang the system.
. Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.
. Go to the diagnostic memory in the test items.
. Press F2 in the test items.
. Follow the instructions in the message window.OTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
er System Checko verify the symptom of the problem, power on the computer using each of the following power sources:
. Remove the battery pack.
. Connect the power adapter and check that power is supplied.
. Disconnect the power adapter and install the charged battery pack; then check that power is supplied by the battery pack.
f you suspect a power problem, see the appropriate power supply check in the following list:
T Check the Power Adapter on page 70
T Check the Battery Pack on page 71
70
Check the Power AdapterUnplug the power adapter cable from the computer and measure the output voltage at the plug of the power a
1
2
N
3
4Chapter 4
dapter cable. See the following figure
. If the voltage is not correct, replace the power adapter.
. If the voltage is within the range, do the following:
T Replace the System board.
T If the problem is not corrected, see Undetermined Problems on page 84.
T If the voltage is not correct, go to the next step.OTE: An audible noise from the power adapter does not always indicate a defect.
. If the power-on indicator does not light up, check the power cord of the power adapter for correct continuity and installation.
. If the operational charge does not work, see Check the Battery Pack on page 71.
Pin 1: +19 to +20.5VPin 2: 0V, Ground
Chap
Check the Battery Pack To check the battery pack, do the following:
F
1
2
3
4
F
1
2
3
To
IR
Iu
TouIn
1
2
3
Acpter 4 71
rom Software:
. Check out the Power Management in control Panel
. In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total Battery Power Remaining are correct.
. Repeat the steps 1 and 2, for both battery and adapter.
. This helps you identify first the problem is on recharging or discharging.
rom Hardware:
. Power off the computer.
. Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the following figure
. If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
o check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50% f the total power remaining when installed in the computer.
f the battery status indicator does not light up, remove the battery pack and let it return to room temperature. e-install the battery pack.
f the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light p, replace the DC/DC charger board.
chpad Checkf the touchpad doesnt work, do the following actions one at a time to correct the problem. Do not replace a on-defective FRU:
. Reconnect the touchpad cables.
. Replace the touchpad.
. Replace the system board.
fter you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement an occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware roblem. No service actions are necessary if the pointer movement stops in a short period of time.
72
Power-On Self-Test (POST) Error Message Tl
N
T
I
Tb
N
NChapter 4
he POST error message index lists the error message and their possible causes. The most likely cause is isted first.
OTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU.
his index can also help you determine the next possible FRU to be replaced when servicing a computer.
f the symptom is not listed, see Undetermined Problems on page 84.
he following lists the error messages that the BIOS displays on the screen and the error symptoms classified y function.
OTE: Most of the error messages occur during POST. Some of them display information about a hardware device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the way it has been configured.
OTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter Setup and install Setup defaults or correct the error.
Chap
Index of Error Messages
E
E
F
S
K
K
K
M
S
S
E
S
Sc
Ster 4 73
rror Code List
Error Codes Error Messages
006 Equipment Configuration ErrorCauses:1. CPU BIOS Update Code Mismatch2. IDE Primary Channel Master Drive Error(THe causes will be shown before Equipment Configuration Error)
010 Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh)
070 Real Time Clock Error
071 CMOS Battery Bad
072 CMOS Checksum Error
110 System disabled.Incorrect password is specified.
Battery critical LOWIn this situation BIOS will issue 4 short beeps then shut down system, no message will show.
Thermal critical HighIn this situation BIOS will shut down system, not show message.
rror Message List
Error Messages FRU/Action in Sequence
ailure Fixed Disk Reconnect hard disk drive connector.Load Default Settings in BIOS Setup Utility.Hard disk driveSystem board
tuck Key see Keyboard or Auxiliary Input Device Check on page 68.
eyboard error see Keyboard or Auxiliary Input Device Check on page 68.
eyboard Controller Failed see Keyboard or Auxiliary Input Device Check on page 68.
eyboard locked - Unlock key switch Unlock external keyboard
onitor type does not match CMOS - Run Setup Run Load Default Settings in BIOS Setup Utility.
hadow RAM Failed at offset: nnnn BIOS ROMSystem board
ystem RAM Failed at offset: nnnn DIMMSystem board
xtended RAM Failed at offset: nnnn DIMMSystem board
ystem battery is dead - Replace and run Setup Replace RTC battery and Run BIOS Setup Utility to reconfigure system time, then reboot system.
ystem CMOS checksum bad - Default onfiguration used
RTC batteryRun BIOS Setup Utility to reconfigure system time, then reboot system.
ystem timer error RTC batteryRun BIOS Setup Utility to reconfigure system time, then reboot system.System board
74
R
Pu
MC
D
I
S
C
D
S
F
D
A
F
F
I
I
O
Error Message List
Error Messages FRU/Action in SequenceChapter 4
eal time clock error RTC batteryRun BIOS Setup Utility to reconfigure system time, then reboot system.System board
revious boot incomplete - Default configuration sed
Run Load Default Settings in BIOS Setup Utility.RTC batterySystem board
emory size found by POST differed from MOS
Run Load Default Settings in BIOS Setup Utility.DIMMSystem board
iskette drive A error Check the drive is defined with the proper diskette type in BIOS Setup UtilitySee External Diskette Drive Check on page 68.
ncorrect Drive A type - run SETUP Check the drive is defined with the proper diskette type in BIOS Setup Utility
ystem cache error - Cache disabled System board
PU ID: System board
MA Test Failed DIMMSystem board
oftware NMI Failed DIMMSystem board
ail-Safe Timer NMI Failed DIMMSystem board
evice Address Conflict Run Load Default Settings in BIOS Setup Utility.RTC batterySystem board
llocation Error for device Run Load Default Settings in BIOS Setup Utility.RTC batterySystem board
ailing Bits: nnnn DIMMBIOS ROMSystem board
ixed Disk n None
nvalid System Configuration Data BIOS ROMSystem board
/O device IRQ conflict Run Load Default Settings in BIOS Setup Utility.RTC batterySystem board
perating s
Top Related