8/19/2019 78494036 QUASAR 1F
1/72
QUASAR 1F
7849 4036 - A-08-06-2006 GP-JP-FL
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
OPERATOR’S MANUAL
Machine serial numbers : 4036 - 4037 - 4059
8/19/2019 78494036 QUASAR 1F
2/72
2 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
1 INTRODUCTION TO MACHINE 4
1/1 INTENDED TO USE 5
1/2 RECOMMENDED OPERATING CONDITIONS 5
1/3 COMPONENTS OF THE MACHINE 5
2 SAFETY & ENVIRONMENTAL INSTRUCTIONS 10
2/1 OPERATOR SAFETY INSTRUCTIONS 10
2/2 MAIN SAFETY HAZARDS IN USE OR MAINTENANCE WORK 11
2/3 ENVIRONMENTAL PRECAUTIONS 13
2/4 TYPE PLATE 14
2/5 GRADIENT ANGLE 14
2/6 SAFETY CANOPY 15
2/7 MACHINE IN TRAMMING POSITION AND PARKING 16
2/8 DANGER AREAS 17
2/8/1 DANGER AREA WHEN TRAMMING 17
2/8/2 DANGER AREA WHEN DRILLING 18
2/9 MANNERS AND CONDITIONS IN WHICH THE RIG SHOULD NOT BE USED 19
2/10 NOISE LEVEL AND NOISE EMISSION 19
2/11 ACCELERATION VALUE 19
2/12 SAFETY EQUIPMENT 19
2/13 FIRE PREVENTION 20
2/13/1 REFILLING FUEL TANK 20
2/14 FIRE EXTINGUISHER (OPTIONAL) 21
2/15 EMERGENCY STOPS, MAIN SWITCHES & EMERGENCY BRAKES 22
2/16 ELECTRIC CABLE 24
3 CHECKS AND INSTRUCTIONS 25
3/1 ASSEMBLY AND CHECKING OF A NEW MACHINE 25
3/2 ROUTINE CHECKS BEFORE STARTING A SHIFT 26
3/3 ELECTRIC PANEL 34
3/4 TRAMMING COMPARTMENT 35
4 TRAMMING 38
4/1 STARTING THE ENGINE 38
8/19/2019 78494036 QUASAR 1F
3/72
3 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
4/2 TRAMMING 39
5 DRILLING 42
5/1 BASIC RULES OF SAFETY 42
5/1/1 SAFETY PRECAUTIONS 42
5/1/2 PRE-START CHECK LIST 42
5/1/3 ROCK DRILL 42
5/1/4 DRILL FEED 43
5/1/5 BOOM 43
5/2 SETTING-UP THE MACHINE IN THE DRIFT 44
5/2/1 MACHINE POSITIONING. 44
5/3 START-UP 455/3/1 ELECTRIC POWER 45
5/3/2 ELECTRIC SUPPLY MAIN BREAKER 45
5/3/3 ELECTRIC CONTROL PANEL 46
5/3/4 MOTOR START-UP 46
5/4 DRILLING COMPARTMENT 47
5/4/1 BOOM MOVEMENTS 48
5/5 DRILL FEED MOVEMENTS 50
5/5/1 DRILLING CYCLE FOR NVT DRILL FEED 51
5/5/2 DRILLING METHOD - FACE DRILLING 52
5/6 DRILLING 53
5/6/1 BEFORE DRILLING 53
5/6/2 COLLARING THE HOLE 53
5/6/3 DRILLING 53
5/6/4 CORRECTING DRILLING DIRECTION 54
5/6/5 FEED RETURN 54
5/6/6 MANUAL PERCUSSION 54
5/6/7 DRILLING IMPERATIVES 55
5/6/8 ENDING A SHIFT 55
6 TRANSPORTATION 56
6/1 TOWING THE MACHINE 56
6/2 TRANSPORT PLATFORM 57
6/3 LIFTING THE MACHINE 58
6/4 STORING THE MACHINE 59
7 TECHNICAL DATA 60
8/19/2019 78494036 QUASAR 1F
4/72
4 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F INTRODUCTION TO MACHINE
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
1 INTRODUCTION TO MACHINE
This manual provides instructions for the use and safe operation of a QUASAR 1F face drilling
machineThe information contained in this manual must be studied and thoroughly assimilated beforeattempting to operate this machine.
One or other of the following symbols have been used throughout the manual in order to highlight aparticular aspect of the machine which the operator must be aware of them at all times.
NOTE: This symbol is used to indicate the specific functioning of a particular component.CAUTION: This symbol is used to indicate that failure to comply with the instructions in this manualcould cause damage to the machine.
WARNING: This symbol is used to warn the operator that improper use of the machine
could cause injury to himself and to those in the immediate area of the machine.The information contained in these paragraphs must be adhered to at all times.Never attempt to operate a machine unless all required preventive maintenance has been
performed. All damage and faulty operation must be reported immediately for corrective action by
authorized maintenance personnel.
NOTE: Any and all operators must be properly trained before attempting to operate this machineunassisted.
WARNING: It is the operator’s responsibility to ensure that the machine is in perfectworking condition. At each machine start-up, a pre-start check list MUST becompleted even if the machine has been used earlier in the day. It is the operator whois at the controls that will assume full responsibility if an accident or injury occurs.
NOTE: Whenever FRONT: REAR: RIGHT: LEFT are mentioned throughout this
manual, it is assumed that the operator is standing at the rear of the machine(Engine end) and looking toward the front (Boom end). Right and left DO NOT
REFER to the operator’s seat but refer to the right and left of the machine.
REARFRONT
8/19/2019 78494036 QUASAR 1F
5/72
5 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F INTRODUCTION TO MACHINE
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
1.1 INTENDED TO USE
The QUASAR 1F is intended for use in mining, preparation work and tunneling.
1.2 RECOMMENDED OPERATING CONDITIONS
• Ambient temperature :-30°C .... +50°C
• Maximum altitude from sea level : 3000m
• Before use in exceptional conditions, contact Sandvik Mining and Construction Lyon’s engineeringdepartment.
1.3 COMPONENTS OF THE MACHINEFRONT SECTION
MAIN COMPONENTS
1. Rock drill
2. Feed
3. Boom
4. Front stabilizers
5. Drilling compartment
1
2
34
FRONT SECTION 5
8/19/2019 78494036 QUASAR 1F
6/72
6 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F INTRODUCTION TO MACHINE
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
ROCK DRILL
1. Low pressure accumulator2. Hight pressure accumulator
3. Rotation motor
4. Flushing housing
5. Percussion assy
1. Pressure accumulator
2. Rotation motor housing
3. Percussion housing
4. Flushing head
Feed
1. Hose reel
2. Rock drill carriage
3. Feed cylinder, wire ropes
4. Centralizers, Rod clamp (optional)
1
2
3
4
5
X2
12
3
4
H200
43
NVTF
1
2
8/19/2019 78494036 QUASAR 1F
7/72
7 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F INTRODUCTION TO MACHINE
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
BOOM
DRILLING COMPARTMENT
Feed Extension
Ensure horizontal //
Ensure vertical //
Boom Lift
Boom Swing
Feed Tilt
Feed Roll-over Divergence
Feed Swing
B14F
Air/oil lubrication Rotation
Boom control levers Feed thrust lever Rotation lever
pressure gaugeWater ball valvesight-glass
KVL10 rock drill oiler
Electric control box
air pressure gauge
Feed rearstinger
8/19/2019 78494036 QUASAR 1F
8/72
8 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F INTRODUCTION TO MACHINE
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
REAR SECTION
MAIN COMPONENTS
1. Operator seat
2. Safety telescopic canopy
3. Cable reel
4. Electric control panel
5. Inside or outside rear stabilizers
(optional)
6. Tramming compartment
7. Oil tank
8. Diesel engine
9. Tuflo 1000 air compressor
10. Fuel tank
11. Electric power pack
12. Water pump
13. Air tank
14. Water supply connection
4
REAR SECTION
5
32
REAR SECTION
1
78
11
612
9
10
13
14
8/19/2019 78494036 QUASAR 1F
9/72
9 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F INTRODUCTION TO MACHINE
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
TRAMMING COMPARTMENT
1. Stabilizers, canopy and diesel
boom supply control valve
2. Cable reel lever
3. Steering lever
4. Fire extinguisher push button
(optional)
5. (O) Emergency/Park brakes push
button
6. Tramming pressure gauge
7. Tramming lever
8. Battery switch
9. Main breaker switch
10. Electric panel
11. Emergency stop push button
12. Diesel engine accelerator
13. Unbraking hand pump (optional)
10
12
1
2
3
8
9
7
6
4
5
13
11
8/19/2019 78494036 QUASAR 1F
10/72
10 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F SAFETY & ENVIRONMENTAL INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
2 SAFETY & ENVIRONMENTAL INSTRUCTIONS
RISK OF INJURY AND AUTOMATIC VOIDANCE OF SANDVIK WARRANTY.
TO WHOM IT MAY CONCERN:
SANDVIK HAS DESIGNED SAFETY FEATURES BECAUSE IT BELIEVES SUCH FEATURES WILL
BETTER PROTECT PEOPLE. DO NOT DO ANYTHING THAT MAY HAMPER SAFETY FEATURES ON
EQUIPMENT.
It is strictly forbidden to make ANY modification to a Sandvik product without prior written approval of the
factory. If ANY modifications are made without written approval, Sandvik Tamrock can not be held
responsible for any accidents, incidents or damage to persons or property, especially if modifications are
made on any safety feature including, but not limited to, safety critical circuits or components.
In many cases, the affect of a modification to a machine's total performance is unknown.
Therefore, if a machine is modified for any reason, even if safety is not affected, Sandvik's warranty will
be void.
2.1 OPERATOR SAFETY INSTRUCTIONS
WARNING: Operation, maintenance and adjustments are only allowed to personswith specific training in operation and maintenance of the equipment. Read the
operating and maintenance instructions before using or servicing the equipment.
WARNING: Plan your work carefully in advance to avoid possible accidents andinjuries. The operator must be familiar with the functions of the equipment beforetaking it into use.
WARNING: The operator must always wear required personal protection, such assafety helmet, protective overall, safety boots, hearing protectors, safety gogglesetc...Always ensure that those protections are in good shape before using them.
WARNING: Adequate ventilation must always be provided.Make sure that ventilation is sufficient to prevent exhaust fumes and dust.Exhaust fumes can be lethal.When operating in confined conditions the exhaust gases and dust must bedirected in such a way that they do not return to the working area and create ahazard.Check regularly the exhaust purifier clogging according to its maintenancemanual.
WARNING: Always have a fire extinguisher at hand and learn how to use it.Have the extinguisher inspected and serviced regularly according to the local
regulations and to the extinguisher maintenance manual.
WARNING
WARNING
WARNING
WARNING
8/19/2019 78494036 QUASAR 1F
11/72
11 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F SAFETY & ENVIRONMENTAL INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
WARNING: Take care of sufficient lightning.
WARNING: Insufficient scaling of drilling site.
2.2 MAIN SAFETY HAZARDS IN USE OR MAINTENANCE WORK
WARNING: MAKE SURE THAT THERE ARE NO UNAUTHORIZED PERSONS IN THEDANGER AREAS DURING DRILLING OR TRAMMING.
WARNING: Simultaneous charging and drilling is strictly forbidden.
WARNING: Always check the efficiency of the safety devices before using themachines: emergency stop push button, emergency brakes, backward tramminglight and buzzer, tramming and working light, horn, etc...
WARNING: All hoods must be correctly mounted on the machine and the doorscorrectly closed and locked, this all the time in order to prevent accident with movingcomponents such a engine belt, cable reel chain, etc...
WARNING: danger of slipping, tripping or falling.Keep the ladders, steps, hand rails, handles and working platforms clean of oil, dirtand ice.
WARNING: Observe the balance of the rig.Never exceed the specified inclination angles when parking, tramming or drilling.
WARNING: While tramming NEVER SWING THE BOOM, if needed SWING THE DRILLFEED.
WARNING: Before moving the booms make sure that the jacks and the stabilizers arefirmly in contact to the ground.
WARNING: Crushing hazard : do not stay in dangerous area, for instance: centralarticulation, front chassis and rear chassis...
WARNING: The movements and rotation of components form also danger areas(boom, feed and drilling equipment).
MAKE SURE THAT THERE ARE NO UNAUTHORIZED PERSONS IN THE DANGER
AREAS.
WARNING
WARNING
8/19/2019 78494036 QUASAR 1F
12/72
12 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F SAFETY & ENVIRONMENTAL INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
WARNING: Danger of hot surface.Hot surface can cause serious injuries.Components as diesel engine, exhaust gas purifier, rod, shank or hydraulic
components can be hot and before starting a maintenance work, please let them cooloff.
WARNING: Service operations should be carried out only when the rig is stopped.Replace or repair faulty tools and equipment.Make sure that there are no unauthorized persons in the working area when youcarry out service and repair work.The drilling equipment must always be kept clean of oil and dirt.
WARNING: Make sure that the boom is properly supported before servicing the
hydraulic system.
WARNING: Danger of high pressure air streams. The air streams can cause seriouspersonal injuries.Release the pressure before opening filling caps or pneumatic connections.
WARNING: The lubricator, the compressor air/oil receiver and any air receiver arepressure vessels and they are not allowed to be repaired without properauthorization.Check regularly the certification validity of those componnents.At the end of validity period, you must make recertify the component by aregistered organization or replace it by a new one.
WARNING: Danger of high pressure oil jets.High pressure oil jets can cause serious personal injuries.Release the pressure in the hydraulic circuits before opening caps or connections.(Accumulator,Cylinder and Hydraulic circuit)
WARNING: If the component must be live, a fellow worker must be standing by to cut
OFF voltage at the emergency or main switch in an emergency situation.
WARNING: If you have to weld the rig, disconnect the alternator cables or open themain switch before starting to weld. Consider also the fire and explosion risk causedby welding. Make sure that the rig and its surroundings are clean and fire-safe.
Gloves
WARNING
WARNING
WARNING
WARNING
+ +- -
8/19/2019 78494036 QUASAR 1F
13/72
13 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F SAFETY & ENVIRONMENTAL INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
2.3 ENVIRONMENTAL PRECAUTIONS
WARNING: Please notice that the hydraulic oil, fuel, and battery liquid can causepollution. Please refer to your own environmental standars for the liquide processing
Before operating maintenance always plan your work in order to use adequate andin good shape receptacles.
Do not use the diesel engine if it is not needed because of exhaust gas, think aboutthe people and the environment.
For decommissioning, scrapping and disposal of machine’s components (dieselengine, tyres, batteries, etc...), you must always observe the law in force in yourcountry.In case of no law or if you think it’s not suficient, you can contact the conponentsupplier.
Always have a fire extinguisher at hand and lurn of to use it.
8/19/2019 78494036 QUASAR 1F
14/72
14 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F SAFETY & ENVIRONMENTAL INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
2.4 TYPE PLATE
2.5 GRADIENT ANGLE
1. Machine name and type
2. Serial number
3. Diesel engine power
4. Electric input power
5. Electric voltage
6. Electric frequency
7. Total weight of the machine
8. Manufacturing date
WARNING: The maximum gradientangle is 15°.
WARNING: The maximum sideslope angle is 5 °.
WARNING: On slippery surfaces,e.g. ice or smooth rock, safetramming and drilling gradientsare much smaller than on surfaceswith good grip.
NB: There are two inclination gauges at the tramming compartment.
QUASAR 1F
12
3
5
4
6
7
8
8/19/2019 78494036 QUASAR 1F
15/72
15 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F SAFETY & ENVIRONMENTAL INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
2.6 SAFETY CANOPY
The canopy is FOPS certified for only 2 positions of the canopy:- Position HIGH for standing operator.
- Position LOW for sitting operator.
These two positions must clearly be marked on thecanopy telescoping leg in order to inform the
operator of the machine.
WARNING: You must paint these two
marks on the canopy leg, using the pen suppliedin the package. Apply a paint line over a width
approximately 15mm (1/2 inch) wide.
CANOPY IN HIGH POSITION CANOPY IN LOW POSITION
High position paint line
Canopytelescoping leg
Low position paint line
Canopy
PAINT LINE
telescoping leg
8/19/2019 78494036 QUASAR 1F
16/72
16 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F SAFETY & ENVIRONMENTAL INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
2.7 MACHINE IN TRAMMING POSITION AND PARKING
• Boom must be in line with the machine axis.
• Lower the drill feed and boom as far as possible.
• Machine must be on stabilizers in parking position.
WARNING: While tramming NEVER SWING THE BOOM, if needed SWING THE DRILLFEED.
WARNING: Crushing hazard : do not stay in dangerous area, for instance: centralarticulation, front chassis and rear chassis...
WARNING
WARNING
TRAMMING POSITION
PARKING POSITION
WARNING
8/19/2019 78494036 QUASAR 1F
17/72
17 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F SAFETY & ENVIRONMENTAL INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
2.8 DANGER AREAS
2.8.1 DANGER AREA WHEN TRAMMING
Do not allow other personnel to stand in the area
shown beside.
DANGEROUS AREAS:
• 5m toward the front end of the drill feed and
5m backward the rear end of the carrier.
• Area between the machine and the side wall
of the drift.
Never allow riders on any part of the machine.
Always sound the horn before starting the engine.
The operator must be attentive at any time and haveto stop the machine if a person is in the dangerous
area
Keep hands, arms, legs and head completely inside
the tramming compartment.
Ensure that the machine is in perfect operating
condition.
Complete in full, at each shift, the pre-start check list.
5 m
5 m
8/19/2019 78494036 QUASAR 1F
18/72
18 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F SAFETY & ENVIRONMENTAL INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
2.8.2 DANGER AREA WHEN DRILLING
DURING DRILLING OPERATION, NEVER ALLOW PERSONNEL TOSTAND IN THE AREA BETWEEN THE DRILLING COMPARTMENT
AND THE ZONE BEING DRILLED.
A MACHINE SHOULD NEVER BE IN AN AREA THAT HAS NOT BEEN
CAREFULLY SCALED.
NO PERSONNEL ALLOWED
NO PERSONNEL ALLOWED
8/19/2019 78494036 QUASAR 1F
19/72
19 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F SAFETY & ENVIRONMENTAL INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
2.9 MANNERS AND CONDITIONS IN WHICH THE RIG SHOULD NOT BE USED
Risk factors for personnel:
• Operator does not have sufficient training.• Unauthorized person are present in the working area.
• Insufficient scaling of the working area.
• Exposition to gases in the drift.
• Safety systems are deficient or out of order.
• The field is charged.
• Transportation of persons.
• Use of the rig for lifting purposes.
• Inadequate ventilation.
• Inadequate lightning.
• Inadequate electric earthing.
• Defective safety devices.
2.10 NOISE LEVEL AND NOISE EMISSION
Noise level
The measurement of the noise emission and the noise level at the operator compartment have been
measured in accordance of the European Standard Drill Rig safety 89/392/EEC and changes of 91/
368/EEC AND 93/44/EEC.
Noise emission:100 db(A) the rockdrill in operation.
Level at the operator compartment: 98 db(A) the rockdrill in operation.
2.11 ACCELERATION VALUE
The measurement of the acceleration value at the operator’s positions have been measured in
accordance of European Standard Drill Rigs - safety 89/392/EEC and changes of 91/368/EEC and 93/
44/EEC.
Acceleration value does not exceed 0.5 m/s2
2.12 SAFETY EQUIPMENT
WARNING: Check the emergency stop buttons and safety equipment for properoperation and condition at the beginning of each shift and always after tramming.
• Fire extinguisher(s)
• Emergency stop buttons
• Safety and protection devices
WARNING: Always check the emergency/park brake efficiency prior to move the
machine.
8/19/2019 78494036 QUASAR 1F
20/72
20 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F SAFETY & ENVIRONMENTAL INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
2.13 FIRE PREVENTION
• Keep the machine clean at all times, especially from fuel, grease, oil rags and paper.• Wash the machine regularly.
• Check fire extinguishers and/or fire prevention equipment daily to ensure that they arein perfect working order.
• Keep electric components and wiring in good condition.
• The filling of tanks must be carried out in a well-ventilated area.
• The control and recharging of batteries must be carried out in a well-ventilated area.
2.13.1 REFILLING FUEL TANK
The following precautions must be observed when replenishing fuel:
• Do not fill fuel tank when the engine is running.
• Take care not to spill fuel on hot surfaces.
• Fuel filling should be done in a well ventilated space.
• Smoking, open flame and sparks are dangerous when the fuel tank is being filled.
• Wipe off spilled fuel before starting the engine.
• Keep the fuel replenishing pipe in contact with the fuel tank or arrange earthing to prevent sparkingcaused by static electricity.
WARNING: Smoking during filling or control operations is forbidden.
8/19/2019 78494036 QUASAR 1F
21/72
21 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F SAFETY & ENVIRONMENTAL INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
2.14 FIRE EXTINGUISHER (OPTIONAL)
The fire extinguisher actuators are located in A at the tramming compartment and in B at the rear ofthe machine, as shown on the drawing.
To activate the fire extinguisher:
• Step 1 : Pull out the lock pin.
• Step 2 : Push the red button.
PIN
PUSH BUTTON
1
2
A
B
8/19/2019 78494036 QUASAR 1F
22/72
22 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F SAFETY & ENVIRONMENTAL INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
2.15 EMERGENCY STOPS, MAIN SWITCHES & EMERGENCY BRAKES
WARNING: Always ensure free access to the emergency stops.
WARNING: Check the operation of the emergency stop at the trammingcompartment prior to use the machine.
When the emergency stop push button is depressed, the Diesel engine and the power pack stop at
once.
EMERGENCY STOP PUSH BUTTON
EMERGENCY STOP
PUSH BUTTON
8/19/2019 78494036 QUASAR 1F
23/72
23 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F SAFETY & ENVIRONMENTAL INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
(O) EMERGENCY/PARK BRAKES
TO ACTIVATE THE BRAKES, PUSH THE RED BUTTON.
WARNING: As the machine may come to an abrupt halt, the operator must be correctlyseated and attentive at all times.
TRANSPORTING PASSENGERS AND STANDING UP WHILE TRAMMING IS STRICTLYFORBIDEN.
WARNING: Memorise the location of this brake valve in order to be able to activate itrapidly in case of emergency.
PUSH BUTTON
(O) EMERGENCY/ PARK BRAKES
Pull = Brakes released
Push = Brakes applied
8/19/2019 78494036 QUASAR 1F
24/72
24 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F SAFETY & ENVIRONMENTAL INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
2.16 ELECTRIC CABLE
WARNING: Never use an electric cable unless it is firmly positioned on itssupport. this will prevent unnecessary tension on the cable which may result inthe plug being pulled from its socket.
The cable must never be live before the machine is ready to drill and the cableitself has been placed in its support and support hooks.NEVER HANDLE A LIVE CABLE.
Never move the machine if the cable is live.To ensure that no vehicle will drive over the cable, lay the cable in hooks whichhave been placed in the sidewall along the length of the gallery being drilled.
BATTERY MASTER SWITCH
CAUTION: In order to prevent thealternator to be damaged, stop theengine prior to turn the battery masterswitch to the «OFF» position.
NOTE: In drilling electric mode, switch offthe battery in order not to dischange thebattery.
ELECTRIC MAIN CIRCUIT-BREAKER
WARNING: Switching off the maincircuit-breaker do not shut off thepower at the cable reel and in thecable connected to the machine.Consequently the cable is still live.NEVER HANDLE A LIVE CABLE.Never leave the machine whilemotors are running.
CAUTION: Do not rotate the mainswitch if a motor is running. Stop allmotors prior to use the main switch.
NOTE: if the electric main circuit-breaker trip OFF automatically due to
an electric problem, move the handlefully to reset position prior to place itback to ON position.
ON
OFF CAUTION
ON
OFFRESET
DANGER
HIGHVOLTAGE
CAUTION
DANGER
HIGHVOLTAGE
8/19/2019 78494036 QUASAR 1F
25/72
25 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F CHECKS AND INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
3 CHECKS AND INSTRUCTIONS
3.1 ASSEMBLY AND CHECKING OF A NEW MACHINE
If the machine is delivered disassembled, please pay special attention to the following points:
• The assembly site must be properly equipped (cleanliness, good lighting, lifting equipment, etc...).
• The assembly operation must be done by qualified personnel.
• Check that all components are delivered.
• Fasten all bolts and connections properly.
• Observe cleanliness when installing hydraulic hoses to prevent particles to enter in the hydraulic
circuit.
• Lubricate all greasing points.
• Wash the machine before using it.
VISUAL CHECKING OF THE NEW MACHINE
CHECK FOR :
• Possible transportation damage.
• Tyre pressure and condition.
• All oil and fuel levels.
CAUTION: Remove the centralarticulation locking bar before movingthe machine.
WARNING: All electric safetydevices must be thoroughlychecked prior to attempt to startthe machine.WARNING: The rock drillaccumulators must be inflated withNITROGEN (N2).
Locking barin locking position
Central articulation
locking bar
CHECK
CAUTION
8/19/2019 78494036 QUASAR 1F
26/72
26 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F CHECKS AND INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
3.2 ROUTINE CHECKS BEFORE STARTING A SHIFT
WARNING: Report any damage or faulty components immediately and do not use themachine.
PINS
TYPE A
• Lock plate 2 must be in contact to thesupport 1.
• Fastening screws in place and tighten.
TYPE B
• Fastening bolt 1 in place and tighten.
TYPE C
• Fastening bolt 1 in place and tighten.
HOSES, FITTINGS AND HYDRAULIC CONNECTIONS
When moving around the machine, look for
hydraulic damages
• Hoses
• Fittings and connections
• Hydraulic leaks
1
2
1
1
8/19/2019 78494036 QUASAR 1F
27/72
27 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F CHECKS AND INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
DIESEL ENGINE OIL LEVEL
• Ensure that the engine oil ilevel s
between the minimum and the maximumlevel marks on the dipstick.
FUEL LEVEL
• Check the fuel level.
• Check for cracks and leaks.
WARNING: Top up the fuel tank in a
well ventilated area.
AIR FILTER
• Ensure that the clogging indicator stays inthe green zone. An indicator located in thered zone calls for filter element
replacement.
• Remove the dust collector to extract thedust.
• Check the hose between the filter and the
engine intake manifold for fraying cracksand damaged clips
Filter cloggingindicator
Dust collector
8/19/2019 78494036 QUASAR 1F
28/72
28 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F CHECKS AND INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
HYDRAULIC OIL LEVEL
• The quantity of hydraulic oil must bemaintained between the maximum andminimum notches on the level sight glass.
CAUTION: To fill up the tank, use thehand pump or the electric filling pump(optional). This ensure that the oil is
filtered before it enters the tank. The oilcapacity contained between theminimum and the maximum level is 60
liters.
TUFLO 1000 COMPRESSOR
• Check the oil level.
• Remove the filling plug.
• The oil sump should be totally filled up.
Level indicator
Oil filling hand pump
Filling cap
8/19/2019 78494036 QUASAR 1F
29/72
29 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F CHECKS AND INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
AIR CIRCUIT
Every day, bleed the air circuit and the air
tank:
• First stop the air compressor.
• Open the drain ball valves to remove the
condensed water.
Close the bleeding valves before starting
the compressor.
PRESSURIZED AIR: Open the
bleeding valves slowly, so as
to prevent heavy air blow.
Check also the water separator clogging.
WARNING
Drain ball valves
Water separator clogging indicator
WARNING
8/19/2019 78494036 QUASAR 1F
30/72
30 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F CHECKS AND INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
KVL10 ROCK DRILL OILER
• Read the gauge, it should show nopressure.
• Open slowly the hand valve to drain thecondensed water.
• Open the cap, This cap includes adipstick. Pull it up, check the rock drill
lubrication oil level.
• Once a week, drain all remaining oil, fillup with new rock drill oil.
WATER SUPPLY
Check the water supply (1):
• Correct water supply connection.
• No leaks in water circuit components.
The mine water supply pressure must stay
between 3 bar and 14 bar.
NOTE: A lack of water or a loss of pressure
stops all drilling operations (percussion,
rotation and feed halted).
Drain ball valve
Gauge
Filling cap
Mine’s water supply connection
8/19/2019 78494036 QUASAR 1F
31/72
31 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F CHECKS AND INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
WATER PUMP
The water pump must be drained before
each start and after each maintenance workon the water circuit.
DRILL FEED AND BOOM
• Ensure that the rock drill cradle (1) guideshoes are correctly positioned and tightly
in place.
• The rock drill/flushing head assembly (2)
must be correctly fastened on its cradleand screws and nuts must be tightened at
the recommended torque (See rock drillmaintenance booklet).
• Ensure that the feed rails (3) are in good
condition and free of dirt which could
obstruct the drilling and bolting movements(wash them if necessary).
• There must be no missing or loose nuts
and screws.
• Check condition of pulleys and cable.• Check condition of centralizers (4) or rod
clamp (optional).
• Check all the hoses for fraying or wear.
NOTE: The hoses must be kept under the
protection of their spiral sheath.
• Check and grease all pins and pulleys.
NOTE : Do not grease the rails.
3
4 2
1
8/19/2019 78494036 QUASAR 1F
32/72
32 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F CHECKS AND INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
Rotary actuator grease nipples
Pin grease nipples
Armature tube grease nipples
8/19/2019 78494036 QUASAR 1F
33/72
33 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F CHECKS AND INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
BOLSTER PIN
The bolster pin must be greased using thetwo deported greasing points.
WHEELS
• Visualy check the tyres, look for
damages.
• Make sure the nuts 1 are correctlytighten.
• Make sure the lock ring is correctly in
place.
• Check the pressure (tyre pressure : front: 8 bar & rear: 5 bar).
Greasing points
1
8/19/2019 78494036 QUASAR 1F
34/72
34 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F CHECKS AND INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
3.3 ELECTRIC PANEL
power packDiesel
Percussion
HOURMETERS
Electric
Main caution light
Alternatorcaution light
Horn
Contact key
Glow plugindicator
Diesel / electricselector
Main supply “OK”
Main supply “ON”
Blower belt failure
Engine oil pressure
caution light
Starting key
Tramming lights
Power pack “OFF”
Buzzer
Fuel tank level
Emergency stoppush button
caution light (optional)
Cable reel endcaution light (optional)
Working lights
Engine temperature
caution light
Power pack “ON”
Power pack “ON”
8/19/2019 78494036 QUASAR 1F
35/72
35 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F CHECKS AND INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
3.4 TRAMMING COMPARTMENT
TRAMMING COMPARTMENT
TRAMMING COMPARTMENT
1. Stabilizers, canopy and diesel
boom supply control valve
2. Cable reel lever
3. Steering lever
4. Fire extinguisher push button
(optional)
5. (O) Emergency/Park brakes push
button
6. Tramming pressure gauge
7. Tramming lever
8. Battery switch
9. Main breaker switch
10. Electric panel
11. Emergency stop push button
12. Diesel engine accelerator
13. Unbraking hand pump (optional)
10
12
1
2
3
8
9
7
6
4
5
13
11
8/19/2019 78494036 QUASAR 1F
36/72
36 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F CHECKS AND INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
STABILIZERS, CANOPY AND DIESEL BOOM SUPPLY
CONTROL VALVE’S LEVERS
• 1. Optional equipment (cleaner).
• 2. Front right outrigger.
• 3. Front left outrigger.
• 4. Rear stabilizing jacks (optional)
• 5. Diesel oil supply to boomcontrols.
• 6. Canopy.
Push the levers to bring the stabilizers
in contact to the ground.Pull the levers to retract the stabilizersin tramming position.
• FIRST retract the rear stabilizing jacks.
• Then retract the front outriggers.
• Position the telescopic canopy sothat it will be at the correct height
with regard to the hidding.
WARNING: Ensurethat the position ofthe boom ishorizontal andcentered with thefront chassis centerline.
WARNING: Never
swing the boom unless all fourstabilizing jacks are in solidcontact with the ground.When tramming, only the drillfeed swing is authorized. referto chapter «drilling» for boomoperation.Always adhere to the grade andside slope limitations.
1234
56
PUSH
PULL
8/19/2019 78494036 QUASAR 1F
37/72
37 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F CHECKS AND INSTRUCTIONS
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
CABLE REEL
• Position the cable reel tensionlever in the middle position .
• Ensure that the power supply
from the mine electric box to themachine is OFF .
• Plug the cable into the mineelectric box.
• Secure the cable on the supportprovided by the mine.
• Move the cable reel tension lever in the controlled reeling/unreeling
cable tension position.
WARNING:Never use anelectric cableunless it isfirmly
positioned onits support. thiswill preventunnecessary
tension on the cable which mayresult in the plug being pulledfrom its socket.The cable must never be livebefore the machine is ready todrill and the cable itself hasbeen placed in its support andsupport hooks.
NEVER HANDLE A LIVECABLE.Never move the machine if thecable is live.To ensure that no vehicle willdrive over the cable, lay thecable in hooks which have beenplaced in the sidewall along thelength of the gallery beingdrilled.
Cable reel tension lever
Push for reelingPull for unreeling
Middle position free
Cable reel end caution light (optional)
DANGER
HIGHVOLTAGE
8/19/2019 78494036 QUASAR 1F
38/72
38 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TRAMMING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
4 TRAMMING
4.1 STARTING THE ENGINE
WARNING: Always make sure before starting the engine that there is no unauthorizedpersons in the danger areas around the machine and that no controls are in operatingposition.
WARNING: Sound the horn to warn any person of your intention to start and move themachine.Make sure that all covers and protective hoods and doors are installed and properlyclosed.
TRAMMING CONTROL PANEL
• Turn the batteries master switch to the ON
position.
• Turn the contact key 1.
• Rotate the selector switch 2 to the left in Dieselposition.
• Turn the tramming light switch 3 to the right.
• Sound the horn 4 to inform everybody of your
intention to start the engine.• Turn the starting key 5.
WARNING
WARNING
3
2
5
4
1
8/19/2019 78494036 QUASAR 1F
39/72
39 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TRAMMING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
4.2 TRAMMING
Using the accelerator lever, bring the engine to FULL RPM. The pressure indicated on the 0-25 barpressure gauge, located at the operator compartment, must read no less than 15 bar.
CAUTION DEVICES
If during the operation, the buzzer sounds and
any of the lights come on, stop the machine and
locate the cause of the audio visual warning
immediately.
The engine oil pressure gauge is situated in the
tramming compartment. The engine oil pressure
must stay above 2 bar while the engine is
running.
EMERGENCY/ PARK BRAKES TEST
Before moving the machine, ensure that the
emergency/parking brakes are in good working
order (spring applied, pressure released).
The pressure supplied by the tramming pump
releases the brakes. A spring system applies the
brakes.
• Apply the brakes by depressing the red button
on the brake valve.
• Slowly move the tramming lever until there isa slight drop in engine RPM.
THE WHEELS MUST NOT TURN DURINGTHIS TEST.
WARNING: IF THE WHEELSTURN, DO NOT USE THEMACHINE AND NOTIFYMAINTENANCE IMMEDIATLY.
Blower beltEngine Engine oil pressuretemperature
failure
CAUTION LIGHTS
Pull = Brake released
Push = Brake applied
8/19/2019 78494036 QUASAR 1F
40/72
40 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TRAMMING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
MOVING THE MACHINE
WARNING: sound the horn to warnpeople before moving the machine.
• Always refer to the maximum gradient angle.
• Make sure the boom is in tramming position.
• Retract the stabilizers (rear first then front).
• Pull up the brake valve to release the brakes.
• Select the direction you want by using theSteering lever 1 to push to move forward, to pull
to move backward.
• Push slowly on the Tramming lever 2.
HOW TO STOP THE MACHINE?
• 1. Steering lever.
• 2. Tramming lever.
• 3. Emergency/Park brake push button.
The machine can be stopped on a flat or graded
surface simply by moving the tramming lever 2 tothe neutral position.
1
2
3
8/19/2019 78494036 QUASAR 1F
41/72
41 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TRAMMING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
WHERE USING LOW SPEED RANGE?
• Drive slowly around corners, sound the hornand warn people in areas you cannot see.
• Observe speed limit regulation.
Speed depend on the position of the Tramminglever 2.
• For fast forward, PUSH the lever from the
NEUTRAL position to MAXIMUM forward.
• For fast backward, PULL the lever from theNEUTRAL position to MAXIMUM backward.
Steering is controled by steering lever 1.
• Push the lever : machine to the right
• Pull the lever : machine to the left.
DIESEL ENGINE ACCELERATOR
The diesel engine is NEVER used to controlspeed and MUST ALWAYS be maintained at max-imun RPM.
NeutralPush = FORWARDPull = BACKWARD
Fast FastSlow Slow
STEERING LEVER
PULL
PUSH
TRAMMING LEVER
Accelerator
8/19/2019 78494036 QUASAR 1F
42/72
42 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F DRILLING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
5 DRILLING
5.1 BASIC RULES OF SAFETY
5.1.1 SAFETY PRECAUTIONS
USER’S SAFETY, HIGH AVAILABILITY AND LOW OPERATING COST are dependent on the
correct use of this machine.MACHINE, UNDERSTAND ITS CAPABILITIES, FOLLOW OPERATING PROCEDURES AND BECONVERSANT WITH THE SAFETY RELATED PROCEDURES CONTAINED IN THIS MANUAL.
A MACHINE SHOULD NEVER BE IN AN AREA THAT HAS NOT BEEN CAREFULLY SCALED
AND ROOFBOLTED.
BEFORE STARTING THE POWERPACK MAKE SURE THAT ALL CONTROL LEVERS ARE IN
NEUTRAL POSITION.
ENSURE THAT THERE IS NOBODY IN THE DANGER AREA BEFORE ATTEMPTING TO MOVETHE BOOM(S).
5.1.2 PRE-START CHECK LIST
WARNING: POSITION THE MACHINE IN AN AREA OF THE DRIFT ROOFBOLTEDBEFOREHAND to proceed with the pre-start check list.
5.1.3 ROCK DRILL
• There must be no missing or loose nuts and screws.
• At each shift, tighten the water flushing head at the recommended torque.• At each shift, tighten the rockdrill screws at the recommended torque.
• Check all the hoses for fraying or wear.
NOTE: Read also the rock drill maintenance manual.
8/19/2019 78494036 QUASAR 1F
43/72
43 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F DRILLING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
5.1.4 DRILL FEED
• Ensure that the guide shoes are correctly positioned and tightly in place.
• The Rockdrill must be able to move without resistance on the guide rails.
• The feed rails are in good condition and free of dirt which could slow down the movement of the
Rockdrill (wash the drill feed if necessary).
• The feed rails are neither loosen or twisted.
• All the rails nuts are properly tightened.
• Check the hose tension. Tighten if necessary to prevent rapid wear or damage.
NOTE: Read also the drill feed maintenance manual.
5.1.5 BOOM
General inspection:All the articulation and cylinder pins must be greased and correctly positioned.
The hoses must be kept under the protection of the spiral sheath which offers two advantages: - preventing the hoses from becoming coated with oil and grease
- preventing wear by direct contact with the ground.
NOTE: Read also the boom maintenance manual.
WARNING! REPORT ANY DAMAGE OR DEFECT IMMEDIATELY.
8/19/2019 78494036 QUASAR 1F
44/72
44 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F DRILLING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
5.2 SETTING-UP THE MACHINE IN THE DRIFT
5.2.1 MACHINE POSITIONING.
Stop the machine so that the distance between the machine and the face to be drilled = the length ofthe drill feed + 300 mm (1 foot).
This position will allow the drill feed to access the lifters which are directly aligned with the machine.
Position of the front triggers, do not over lift the chassis for maximum stability (see figure).WARNING: When placing the stabilizers, pay attention that nobody is close to them.
Position ofDrill feed overall length
2’the lifter
Mini. clearance
Maximum front stability
Maximum rearstability
8/19/2019 78494036 QUASAR 1F
45/72
45 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F DRILLING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
For optimum stability, and perfectly parallelholes, the carrier must be aligned with thegallery being drilled.
Place the machine lengthways of the drift atan equal distance from the sidewalls.
5.3 START-UP
5.3.1 ELECTRIC POWERCheck following points before switching the main breaker on.
• Machine correctly installed
• Water hose connected
• Air hose connected (optional)
• Electric cable carefully positioned along the sidewall
5.3.2 ELECTRIC SUPPLY MAIN BREAKER
Place the main breaker in position ON.
NOTE: To be able to use the main electric switch you should turn first the battery master switch ON.Rotate then the main switch in position ON.
After using of the emergency stop button the main breaker will be placed automatically in TRIP
position.
To reset the power to the machine- Rotate the lever fully to OFF position.- Then rotate clockwise in ON position.
NOTE: do not use the emergency stop button in normal process to stop any of the power pack, usededicated stop button
ON
OFFRESET
8/19/2019 78494036 QUASAR 1F
46/72
46 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F DRILLING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
5.3.3 ELECTRIC CONTROL PANEL
If the electric supply is correct following lights must glow:
• Main electric supply light.
• Phase setting light.
THE MOTOR(S) CAN NOW BE STARTED. While the motor is running the «motor running» light is
activated.
5.3.4 MOTOR START-UP
- Ensure that all the control levers for the hydraulic control valves, particularly the BCI lever, are in
the NEUTRAL POSITION.CAUTION: NEVER START A MOTOR WHILE IT IS UNDER LOAD.
Position the tramming/drilling selector to the DRILLING POSITION symbolized by the power symbol(turn the switch clockwise).
Depress the start button. The motor will start-up.CAUTION: WAIT SEVERAL SECONDS BEFORE USING ANY ONE OF THE CONTROL LEVER
Power pack ON
Power pack OFF
Phase settingPower packON
light
selector switchDiesel / Electric
Main electricsupply “ON”
8/19/2019 78494036 QUASAR 1F
47/72
47 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F DRILLING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
5.4 DRILLING COMPARTMENT
Air/oil lubrication Rotation
Boom control levers Feed thrust lever
pressure gaugeWater ball valvesight-glass
KVL10 rock drill oilerair pressure gauge
Feed rearstinger
Rotation leverDown : Drilling rotationUp : Reverse rotation
Automatic returnManual feed(for maintenance use only)
ELECTRIC CONTROL BOX
(optional)Manual percussion
(Half power)
Air flushing
OFF - ON
(optional)
8/19/2019 78494036 QUASAR 1F
48/72
48 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F DRILLING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
5.4.1 BOOM MOVEMENTS
BOOM CONTROLS
Feed Extension
Ensure horizontal //
Ensure vertical //
Boom Lift
Boom Swing
Feed Tilt
Feed Roll-over Divergence
Feed Swing
Rod Clamp
Rear Stinger
Optional
1
2 3
4 5
LEF T RIGHT
P USH
P ULL
P USH
P ULL
P USH
P ULL 6
7
8/19/2019 78494036 QUASAR 1F
49/72
49 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F DRILLING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
LEVER 1 - ROD CLAMP
• PUSH : Rod clamp closing.
• PULL : Rod clamp opening.
LEVER 2 - BOOM LIFT & SWING
• PUSH : Boom down.
• PULL : Boom up.• RIGHT: Right boom swing.
• LEFT: Left boom swing.
LEVER 3 - FEED EXTENSION & ROLL-OVER
• PUSH : Feed extension.
• PULL : Feed retraction.
• RIGHT: Right feed roll-over.
• LEFT: Left feed roll-over.
LEVER 4 - FEED SWING
• PUSH : Left feed swing.
• PULL : Right fed swing.
LEVER 5 - FEED TILT
• PUSH : Down feed tilt.
• PULL : Up feed tilt.
LEVER 6 - DIVERGENCE
• PUSH : Up feed divergence.
• PULL : Down feed divergence.
LEVER 7 - REAR STINGER
• PUSH : Rear stinger retraction.
• PULL : Rear stinger extension.
FEED PRESSURE ADJUSTMENT KNOB
• Turn clockwise to increase pressure,
counter clockwise to decrease
pressure.
8/19/2019 78494036 QUASAR 1F
50/72
50 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F DRILLING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
5.5 DRILL FEED MOVEMENTS
Front head extension
Rod clamp
Feed
Feed extesion
Rear stinger(Optional)
(Optional)
8/19/2019 78494036 QUASAR 1F
51/72
51 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F DRILLING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
5.5.1 DRILLING CYCLE FOR NVT DRILL FEED
1 - FRONT HEAD EXTENSION / CRADLE WITHDRAW
2 - FEED EXTENSION UNTIL CONTACT WITH
3 - DRILLING UP TO THE CRADLE STOP
5 - END OF THE DRILLING CYCLE
FRONT HEAD’S CYLINDER STROKEUNTIL THE END OF THE
4 - AUTOMATIC FEED FORWARD MOTION
THE FACE TO BE DRILLED
CradleFront head
8/19/2019 78494036 QUASAR 1F
52/72
52 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F DRILLING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
5/5/2 DRILLING METHOD - FACE DRILLING
• Disconnect and remove the rod clamp.
• Withdraw the rear prop.
• Unlock the front head by removing the locking plate (see Bellow).
• Position the drill feed using boom’s movements levers.
• Phase 1 - Withdraw the drilling cradle and the front head’s extension will start as soon as the cradleis fully retracted.
• Phase 2 - Bring the stinger in contact with the rock using the feed extension movement.
• Phase 3 - Proceed to "hole collaring" then drill the rock up to the end of the drill feed travel.
• Phase 4 - When the cradle is in maximum forward position on the drill feed, an automatic controlvalve control the retraction of the "feed extention" cylinder. Then both drill feed and rockdrill willmove frorward and progress in drilling. During this phase, keep the feed forward lever in maximum
feed position.
• Phase 5 - The front head is fully withdrawn. The rock drill reaches the end of the drilling cycle inahead postion. For a new drilling cycle, proceed to phase 1.
LOCKING PLATE TO BE REMOVED IN ORDER TO UNLOCK THE FRONT HEAD
8/19/2019 78494036 QUASAR 1F
53/72
53 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F DRILLING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
5.6 DRILLING
5.6.1 BEFORE DRILLINGINITIAL CONTROLS:
• Be sure that the position and the direction of the hole is correct.
• Be sure that the drill feed is firmly placed against the face and maintained in that position throughoutthe drilling operation.
• Open the water flushing valve.
The pump will start automatically if the inlet water pressure is greater than 2 bar (51 psi).
NOTE: If the water pressure supplied by the mine is less than 2 bar or if the water filter is clogged,the water pump stops automatically.
5.6.2 COLLARING THE HOLE
• Push the rotation lever DOWNWARD.
• Slowly push DOWNWARD the feed thrust lever. When the bit touches the face, low energy
percussion will automatically start.
When drilling in difficult location as lifters or side wall holes: do not operate the rotation and usegently the feed forward then activate the MANUAL PERCUSSION .
STOP this process as soon as the bit has taken its place into the rock.Use this process for few seconds only to place all the carbide inserts properly in contact to the rock.
• When the bit has penetrated the rock, the collaring process is finished.
• Re-centre the rod in the rod guide if necessary while the machine is still drilling.
5.6.3 DRILLING
• According to drilling conditions, proceed drilling with water flushing.
• Keep the rotation lever pushed DOWNWARD.
• Push the feed thrust lever DOWNWARD to the MAXIMUM feed position.
NOTE: The feed forward movement stops if there is lack of air pressure or water flow.
8/19/2019 78494036 QUASAR 1F
54/72
54 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F DRILLING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
5.6.4 CORRECTING DRILLING DIRECTION
CAUTION: Displacing the boom once the bit has penetrated the rock will create stress on the rod
guides, the articulations, and the cylinders. The only correction allowed is recentering the rod in therod guides.
Correction while drilling:
• Using the feed extention lever, return the drill feed to allow the stinger to loose contact to the face.
• Move the boom until the rod is recentered in the rod guides.
• Use the feed extention forward until the drill feed is in contact with the face.
5.6.5 FEED RETURN
1 - MANUAL RETURN
Move the feed lever upward to activate the rock drill’s backward movement.
2 - AUTOMATIC RETURN (OPTIONAL)
If the automatic feed return is set active, at the electric control box, then, when the rock drill hasreached the end of the drill feed, an automatic device activates the return of the rock drill.Leave the feed lever in position until complete rod retraction.
CAUTION: After complete retraction, do not forget to position the feed lever in the neutral position(lever in upward position) before positioning the boom to drill the next hole to avoid oil overheating.
3 - ROD UNCOUPLING
Recommended procedure for uncoupling the bit or the shank adaptor.
• Anchor the drill feed and then open the water circuit.
• DO NOT USE THE ROTATION.
• Using the Feed Lever , advance the rockdrill.
• Move the Feed Lever to the ’MAXIMUM feed’ position. This allows the full percussion energy to beactivated for a better breaking capability.
5.6.6 MANUAL PERCUSSION
Push the manual percussion button at the electric control box.Half energy percussion is activated.It is possible to use the manual percussion and the feed control lever to advance or return.
CAUTION: When using manual percussion, most of the energy generated by the percussion isabsorbed by the rock drill itself, the front head and the carriage assembly. An excessive use of
manual percussion will result in rapid wear of the water flushing head, and premature breaking ofthe shank.
8/19/2019 78494036 QUASAR 1F
55/72
55 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F DRILLING
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
5.6.7 DRILLING IMPERATIVES
The following rules guarantee optimum drilling performance, resulting in
high productivity at low operating costs.
The drilling tools must be in good operating condition.1 - THE BIT
A correct clearance angle and proper water pressure, evacuate the cutting
as soon as they have been broken from the face.
CAUTION: Drilling with a worn bit results in an increase in rotation torque
and loss of penetration rate.
To increase productivity a worn bit should be replaced with a new or
resharpened one.
5.6.8 ENDING A SHIFT
When you stop the drilling process at the end of the shift or for any other reason, carry on following
operations:
• Tilt the front end of the drill feed downward the stinger in contact to the ground.
• Stop the powerpack
• Close the water supply valve at the mine line
• As to prevent the alternator to be damaged, stop the diesel engine prior to turn the battery masterswitch to the "OFF" position.
• Place the main electric breaker to the "OFF" position
• Shut OFF the power at the mine electric box.
• Wash the machine mainly the drill feed and the boom.
• Fill-up the shift report form.
• Report any defects that you have noticed.
Clearance Angle
8/19/2019 78494036 QUASAR 1F
56/72
56 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TRANSPORTATION
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
6 TRANSPORTATION
6.1 TOWING THE MACHINE
WARNING:THE MAXIMUM TOWING SPEED MUST BE 1 KM/H. This to prevent the
tramming component to be damaged and operator affect at drilling compartment.
THE USE OF CABLE OR CHAIN IS STRICTLY FORBIDEN. While towing, one
operator should be at the tramming compartment ready to apply the brake in a case
of emergency or operate the steering valve to allow the steering cylinder to move.
If it is necessary to tow the machine, comply to
the following procedure:
• Ensure that the power supply from the mine
electric box to the machine is OFF.
• Unplug the cable into the mine electric box.• Connect up the towing machine to the
towed machine with a RIGID BAR. Hook the
bar at the towing points located at the rear
of the machine (see the figure below).
CAUTION: Never try to tow the machine if
the multi-function HP valves, located on the
tramming pump (see figures below) are
tightened. The maximum towing distance
allowed is 1/2 km, over this distance the
hydraulic motor(s) could be damaged due tolack in internal lubrication.
• Untight the both valves and turn them four
revolutions counter-clockwise, to by-pass
the oil flow. The tramming motor can now
turn without resistance.
• Release the emergency/park brake valve by pulling, fully upward, the red knob.
DANGER
!
Unbraking hand pumpTramming pump
Towing point
(optional)
multi-function HP valves
valve in towing position
Unscrew
Oil by pass
8/19/2019 78494036 QUASAR 1F
57/72
57 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TRANSPORTATION
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
• Close the ball valve of the unbraking hand-pump.
WARNING: This ball valve must be always open in normal use of the machine. If not, the park brake may not work, don’t forget to reopen the ball valve after towing the machine.
• Use the unbraking hand pump to pressurize the brake cylinders. The pressure build up by the handpump is sufficient to release the brakes.
NOTE: The brake valve is always functionning. To apply the brakes push downward the red knob, as
you do in normal conditions.
WARNING: Never try to tow a machine which presents problems on tramming
components
WARNING: The valves should be retighten as soon as the towing process as been
completed. NEVER START THE ENGINE THE HP VALVES UNTIGHTEN IN
TOWING POSITION.
6.2 TRANSPORT PLATFORM
WARNING: BEFORE DRIVING THE MACHINE ONTO A TRANSPORT PLATFORM,
MOVE THE BOOMS AND THE FEEDS INTO THE TRAMMING POSITION. NEVER
EXCEED THE MAXIMUM SIDE AND SLOPE LIMITATION.
When driving the machine onto a transport platform, use ramps. this should always be done on level
ground.
Always use low speed and observe special caution when coming from the ramps to the platform.
WARNING: It is imperative to block the two locking screws at the central articulation.
Before moving the platform:
- Lower all stabilizers against the platform floor.
- Move the booms as low as possible and fasten them to platform.
- Fasten the machine chassis to the platform using proper straps or chains.
DANGER
!
DANGER
!
DANGER!
DANGER
!
8/19/2019 78494036 QUASAR 1F
58/72
58 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TRANSPORTATION
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
6.3 LIFTING THE MACHINE
WARNING: Always respect the law and all the local safety regulations in lifting work.Keep in mind the total weight of the rig, given on the type plate.Move the boom and the drill feed or turret to the tramming position .Install the locking bar at the central articulation. Install 4 hooks and chains orcables at the front and rear lifting points.
WARNING: Do not stand under the machine during lifting process. Use proper liftingdevices such as hooks, cables or chains for a safe work.Use a lifting frame to maintain all 4 four chains or cables vertical and parallel toeach other.
Lifting hook
WARNING
Lifting hook
WARNING
LIFTING FRAME
Central articulation locking bar
WARNING
8/19/2019 78494036 QUASAR 1F
59/72
59 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TRANSPORTATION
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
The lifting device used must be of the correct type and have sufficient lifting capacity.
The rig or parts of it must not be lifted with any devices that are not specifically designed for lifting
purposes.
You must always know the exact weight of the load, and never exceed the lifting capacity specified by the
manufacturer of the lifting device.
Lifting routes should be planned so that the load is not moved over persons or such places where persons
may be present.
Make sure that the lifting equipment is in proper condition Wire ropes and chains used for lifting must be
checked regularly. Damaged wire ropes must be marked clearly and discarded at once.
Lift the load only a few centimetres at first to make sure that it is properly fastened and in balance. Do not
continue lifting until you are sure of proper fastening and balance.
The lifting wire ropes must be fastened according to the manufacturer’s instructions.
6.4 STORING THE MACHINE
• The storing place temperature should be higher than the freezing point, and protected against direct
sunlight and rain.
• Wash the machine if it has been used or transported by sea using a high pressure steam washing
machine.• Drain and blow air through the water circuit. Blow some anti-freeze (rust inhibitor) through the
circuit.
• Lubricate all greasing points.
• Bring the stabilizers in contact to the ground.
• The drill feed stinger should be in contact to the ground.
• The nitrogen rockdrill accumulator should be empty, PLACE A TAG TO REMIND THAT THE
ACCUMULATORS HAVE BEEN DISCHARGED.
• Coat the cylinder rod with grease.
• Drain the air reservoir(s).
• Replace all fluids: engine, hydraulic axle and gear oil.
• Spray a dust and corrosion inhibitor product on all electric devices.
• As to prevent the alternator to be damaged, stop the engine prior to turn the battery master switch
to the «OFF»position.
8/19/2019 78494036 QUASAR 1F
60/72
60 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TECHNICAL DATA
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
7 TECHNICAL DATA
Technical Specification
QUASAR F
6-110 S-C2003-01-27
APPLICATION
The Tamrock Quasar 1F is a compact and flexible single
boom electro hydraulic jumbo for mining development in
cross sections up to 24 m².
The robust universal boom have a large optimum
shaped coverage, 360° rotation and full automatic
parallelism for fast and easy face drilling. The boom can
also be used for cross-cutting and bolt-hole drilling.
The jumbo layout is designed for good visibility and
balance, this and the powerful four-wheel-drivearticulated carrier ensure fast and safe manoeuvering in
small drifts.
The high performance drilling system allows high drilling
performance with good drill steel economy and high
machine reliability.
The operator environment and added automatic
functions allow the operator to concentrate on safe, fast
and accurate drilling.
All the service points are well protected but easy to
access.
MAIN SPECIFICATIONS
Carrier 1 x Quasar
Rock drill 1 x X 2 F
Boom 1 x B 14 F
Feed 1 x CC 2500
Length 9 090 mm
Width 1 200 mm
Height roof down 1 850 mm
roof up 2 750 mm
Turning radius 5 100 / 3 400 mm
Tramming speed horizontal 6.5 kph13%=1;7=8° 4 kph
Gradeability, maxi 35 %
Noise level < 98 dB(A)
Weight 9 100 kg
8/19/2019 78494036 QUASAR 1F
61/72
61 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TECHNICAL DATA
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
Technical Specification
QUASAR F
6-110 S-C
2003-01-27
ROCK DRILL (Technical specification 2-310 S)
Model X 2 F
Standard male shank R 38 - T 38
Weight 135 kg
Impact frequency 52 - 59 Hz
Percussion pressure 160 - 210 bar
Impact power 14 - 19 kW
FEED (Technical specification 3-100 S)
Model CC 2500
Drill steel H 25 till H 35
FEED ALTERNATIVE (Technical specification 3-401 S)
Model NVTF
Type Telescopic
Steel length 6/10 ft
Drill steel H 25 till H 35
BOOM (Technical specification 4-100 S)
Model B 14 F
Type Parallel holding
Weight (with hoses) 1 500 kg
Feed roll-over 360°
Feed extension 2 000 mm
HYDRAULIC CONTROL SYSTEM
Type IBCQF
Control functions Auto smooth collaring
Precise anti-jamming
Only 1 control lever for thrust/percussion(full & half)
ELECTRO HYDRAULIC POWER PACK
Electrical motor 45 kW (60hp)
Hydraulic pump type Radial piston
Fixed displacement
CC2508
CC2510
CC2512
CC2514
Total length (mm) 4055 4665 5275 5880
Drill steel length (mm) 2475 3090 3700 4305
Hole depth (mm) 2090 2700 3310 3910
Net weight (kg) 300 360 420 480
Feed force, max. (kN) 12 12 12 12
220
4735
1000 1195 1910
16501850
900
1300
Overall Length
CC 2508 9 090
CC 2510 9 090
CC 2512 9 530
CC 2514 9 670 All dimensions in mm
150
GENERAL DIMENSIONS
8/19/2019 78494036 QUASAR 1F
62/72
62 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TECHNICAL DATA
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
Technical Specification
QUASAR F
6-110 S-C
2003-01-27
CARRIER (Technical specification 1-100 S)
Model Quasar
Diesel engine Deutz F3L 912 W, 30 kW (41 hp)
- Exhaust Catalyser
Hydrostatic transmission
- One pump Variable displacement
Axial piston, 0-75 cm³/rev
- Four wheel-motor Radial piston
Oscillation Rear axle, 2 x 6°
Tyres 10.00 x 15
Steering Frame steering, 2 x 30°
Brakes
- Service Hydrostatic transmission
- Emergency & parking Hydraulic oil immersed
multiple disc brakes on each wheel
Stabilizers 2 hydraulic outriggers, front
- with 14 ft.or telescopic feed 2 hydraulic jacks, rear
Safety canopy Hydraulic, FOPS
- Lowering capability 900 mm
Fuel tank 60 litre
Hydraulic tank 130 litre
AIR CIRCUIT
Compressor C.T. 1, piston type- Capacity 400 l/min.at 4 bar
Electric motor 3 kW (4 hp)
WATER CIRCUIT
Water booster pump W.B.P. 2, centrifugal
- Capacity 4000 l/h at 15 bar
- Electric motor 4 kW (5.5 hp)
Oil cooler OC 25, water-actuated counterflow
- Cooling capacity 25 kW
ELECTRICAL SYSTEM
Total installed power 60 kW
High / Low voltage Separate cabinets
Voltage Standard 380 - 660 V
Alternative 1 000 V
Frequency 50 or 60 Hz
Starting method Star / Delta
Cable reel CRQ type (Technical specification 5-500 S)
- Capacity 80 m of cable 32 mm O.D
Lighting
- Working lights 2 x 70 W, 24 V
- Tramming lights 3 x 70 W, 24 V(the 2 front lights are also used as working lights)
FULL DIESEL VERSION AVAILABLE
Air-cooled engine Deutz F6L 912 W
- Max. rating at 2300 rpm 54 kW (74 hp)
Fuel tank capacity 170 litre
Compressor & water pump driven by hydraulic motors
Total machine weight 8 200 kg
270030°
B
A
All dimensions in mm
Outriggers A B
Standard 2360 2700
Narrow 2015 2100
MINI OPERATING SECTIONTURNING RADIUS
220
2195 1910
1650
1850
4735
Overall Length
CC 2508 9 090
CC 2510 9 090
CC 2512 9 530
CC 2514 9 670
3400
5100
1200
TRAMMING DIMENSIONS
8/19/2019 78494036 QUASAR 1F
63/72
63 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TECHNICAL DATA
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
Technical Specification
QUASAR F
6-110 S-C2003-01-27
DRILLING SYSTEM
H.A.R. Rock drill auto-return.
Drill angle measuring instrument TMS D2.
Air flushing.
Air mist flushing kit for auxiliary water/air connection.
*) Front clamping head on drill feed.
BRAKES
Hand pump for manual brake release.
ELECTRICAL SYSTEM*) 1 000 V electric power supply.
Ground fault detector
- not applicable to 1 000 V
Electric cable (Technical specifications 5-506 S and 5-507 S)
- 380-575 V, 4 x 25 mm², ø 32 mm, 80 m length
- 660-690 V, 4 x 25 mm², ø 32 mm, 80 m length, direct start
*) Allen Bradley electrics.
CARRIER
*) Front narrow outriggers for confined areas + 2 rear jacks.
*) Extendable front jacks.
Fume diluter.
*) Electric oil filling pump.
Hydraulic low oil level indicator and switch.
Complete spare wheel.
*) 4 Michelin X mine D2 instead of standard types.
OTHER OPTIONAL EQUIPMENT
Fire suppression system ANSUL, 6 nozzles.Reverse alarm.
*) EU, UL, CSA, AUS norms package + local standards and
regulations.
Automatic lubrication system (Lincoln) for both boom and carrier.
Central lubrication system.
Hook up for mine air network (IP5 air cleaner included).
*) Ni-Cr plated cylinder rods.
Manuals other than French/English language.
*) replaces standard component
OPTIONAL EQUIPMENT
COVERAGE AREA
Quasar 1F on jacks.
Auto-parallel coverage
Extra coverage with manual override
3600
4400
4500
5500
All dimensions in mm.
8/19/2019 78494036 QUASAR 1F
64/72
64 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TECHNICAL DATA
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
Technical Specification
X Series Rock Drill
2-310 S-C2003-11-27
APPLICATION
The X2 hydraulic rock drill is designed for tunneling andmine development drilling with Tamrock Axera jumbos.It is also suitable for bolt hole and long hole drilling.
DESCRIPTION
The X2 series is a hydraulic percussive rock drill with
independent reversible rotation and low profile height.
Two X2 models are available.
The X2 F, designed for face drilling or rock bolting,
equipped with :
- a 125 cm³ rotation motor,
- a stainless flushing head (optional) with stainlesssteel water cartridge replaceable without removingthe shank.
The X2 L, designed for long hole drill ing, equipped with :
- a high-torque 200 cm³ rotation motor,- a flushing enabling retro-percussion (optional).
It is possible to switch over from version X2 F to versionX2 L simply by changing the rotation motor and theflusning head.
TECHNICAL DATA
Drill steel drifting H32 - H35 drifter rodslong hole drilling Ø39 - Ø45 mm MF rods
T38 - T45 tube
bolt hole drilling H25 - H28
Shank male R38 - T38 - T45 - R32
Hole diameter blast hole 43 - 51 mmburn cut hole 76 - 127 mm
long hole T38 64 - 76 mm
long hole T45 76 - 89 mmbolt hole 35 51 mm
Weight (w/o flushing head 135 kg
Length (w/o shank 969 mm
Profile height 87 mm
Impact rate 52 Hz
Impact power 14 -21 kW
Percussion hydraulic pressure 160-210 bar
OPTIONAL EQUIPMENT
Flushing head.Special tools for X2
8/19/2019 78494036 QUASAR 1F
65/72
65 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TECHNICAL DATA
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
Technical Specification
X Series Rock Drill
2-310 S-C2003-11-27
Accumulator gas Nitrogen N2
High pressure (HP) 55 bar
Low pressure (LP) 4 bar
Filling valve Vg8 DIN 7756
Flushing
Water flow 25 l/min (12 bar)
Water pressure 12-15 bar
Working temperature (water flushing)
Ambient temperature +0...+40° COil operating pressure +40...+60° C
Shank lubrication
Air flow (at 2.5 bar) 250 Nl/min
Pressure 2.5 bar
Oil consumption 100 g/h
Hose fitting size
Percussion JIC 1 1/16 - 3/4
Rotation X2 F JIC 7/8 - 5/8
X2 L JIC 1 1/16 - 3/4
Lubrication JIC 9/16 - 3/8
Flushing JIC 7/8 - 1/2
Drain X2 F JIC 3/4 - 1/2
X2 L JIC 7/8 - 5/8
WORKING PARAMETERS
X2 F X2 L (30 m)
Percussion mechanism
Operating pressure 160 - 210 bar 175 - 210 bar
Percussion power 14 - 19 kW 15 - 19 kW 16 - 21 kW
Percussion rate 52 - 59 Hz 57 - 59 Hz 53 - 55 Hz
Flow 90 l/min 90 l/min
Rotation mechanism
Motor Orbit type, 125 ccm Orbit type, 200 ccm
Flow 40 - 70 l/min 40 - 70 l/minRotation speed 220 - 350 rpm 135 - 240 rpm
Pressure 175 - 210 bar 140 - 175 bar
Torque 390 - 470 Nm 500 - 620 Nm
GENERAL DIMENSIONS
X 2 F X 2 L
87 115
190
155 130
1099
969
1099
969
190
155 130
8/19/2019 78494036 QUASAR 1F
66/72
66 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TECHNICAL DATA
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
Technical Specification
HYDRASTAR 200 Rock DrillHYDRASTAR 200 Rock DrillHYDRASTAR 200 Rock DrillHYDRASTAR 200 Rock Drill2-100 S-B2004-05-06
APPLICATION
The Hydrastar 200 hydraulic rock drill is designed forrock bolting in hard rock with Tamrock Robolt bolters.It is also suitable for tunneling and mine developmentdrilling with Tamrock Quasar jumbos.
DESCRIPTION
The Hydrastar 200 is a hydraulic percussive rock drillwith independent reversible rotation and low profileheight, specially designed for upward drilling.
The Hydrastar 200 is equipped with :
- a 125 cm³ direct mounted rotation motor,- a separate lateral flushing head with easily replace-able water cartridge.
TECHNICAL DATA
Drill steel bolt hole dri ll ing H25 - H28 drifter rodsH22 - H25 integral rods
drifting H25 - H28 drifter rods
Shank bolting Female R25-R28-R32dri fting Male R32-R38
Hole diameter bolt hole 27 - 45 mmblast hole 35 - 41 mm
burn cut hole 76 - 89 mm
Weight (w/o flushing head 95 kg
Length (w/o shank 583 mm
Profile height 70 mm
Impact rate 40 - 65 Hz
Impact power 6 -10 kW
Percussion hydraulic pressure 140 - 200 bar
Noise level 103 dB(A)
OPTIONAL EQUIPMENT
Flushing head (+ 20 kg).Special tools for Hydrastar 200
8/19/2019 78494036 QUASAR 1F
67/72
67 (72) 7849 4036 - A-08-06-2006 GP-JP-FL
QUASAR 1F TECHNICAL DATA
SANDVIK MINING AND CONSTRUCTION LYON S.A.S.19, av. De Lattre de TassignyB.P. 46 - 69881 LYON cedex, FRANCETel: +33 (0)4 72 45 22 00 Fax: +33 (0)4 78 31 79 80
Technical Specification
HYDRASTAR 200 Series Rock DrillHYDRASTAR 200 Series Rock DrillHYDRASTAR 200 Series Rock DrillHYDRASTAR 200 Series Rock Drill2-100 S-B2004-05-06
45
40
35
30
25
20
15
10
5
0
0 100 200 300 400 500
1 0 l / m i n
2 0 l / m i n
3 0 l / m i n
4 0 l / m i n
5 0 l / m i n
6 5 l / m i n
8 0 l / m i n
5
Top Related