CISCO 300-115 CCDP CISCO
CERTIFIED DESIGN PROFESSIONAL
ABOUT 300-115 EXAM QUESTIONS
Implementing Cisco IP Routing (ROUTE 300-115) is a 120-minute qualifying exam
with 50‒60 questions for the Cisco CCNP Routing and Switching and CCDP
certifications. The ROUTE 300-115 exam certifies the routing knowledge and skills of
successful candidates. They are certified in using advanced IP addressing and routing in
implementing scalable and highly secure Cisco routers that are connected to LANs,
WANs, and IPv6.
FEATURES
Real Exam Questions Answers
100% Passing Guarantee
PDF Dumps
Free Demo
CISCO 300-115 EXAM QUESTIONS ANSWERS
Question: 1
What is the maximum number of switches that can be stacked using Cisco
StackWise?
A. 4
B. 5
C. 8
D. 9
E. 10
F. 13
Answer: D
CISCO 300-115 EXAM QUESTIONS ANSWERS
Question: 2
A network engineer wants to add a new switch to an existing switch stack.
Which configuration must be added to the new switch before it can be added
to the switch stack?
A. No configuration must be added.
B. stack ID
C. IP address
D. VLAN information
E. VTP information
Answer: A
CISCO 300-115 EXAM QUESTIONS ANSWERS
Question: 3
What percentage of bandwidth is reduced when a stack cable is broken?
A. 0
B. 25
C. 50
D. 75
E. 100
Answer: C
CISCO 300-115 EXAM QUESTIONS ANSWERS
Question: 4
After the implementation of several different types of switches from different
vendors, a network engineer notices that directly connected devices that use
Cisco Discovery Protocol are not visible. Which vendor-neutral protocol could
be used to resolve this issue?
A. Local Area Mobility
B. Link Layer Discovery Protocol
C. NetFlow
D. Directed Response Protocol
Answer: B
CISCO 300-115 EXAM QUESTIONS ANSWERSQuestion: 5
Several new switches have been added to the existing network as VTP clients. All of the new
switches have been configured with the same VTP domain, password, and version. However,
VLANs are not passing from the VTP server (existing network) to the VTP clients. What
must be done to fix this?
A. Remove the VTP domain name from all switches with "null" and then replace it with the
new domain name.
B. Configure a different native VLAN on all new switches that are configured as VTP clients.
C. Provision one of the new switches to be the VTP server and duplicate information from
the existing network.
D. Ensure that all switch interconnects are configured as trunks to allow VTP information to
be transferred.
Answer: D
CISCO 300-115 EXAM QUESTIONS ANSWERS
Question: 6
After implementing VTP, the extended VLANs are not being propagated to other VTP
switches. What should be configured for extended VLANs?
A. VTP does not support extended VLANs and should be manually added to all switches.
B. Enable VTP version 3, which supports extended VLAN propagation.
C. VTP authentication is required when using extended VLANs because of their ability to
cause network instability.
D. Ensure that all switches run the same Cisco IOS version. Extended VLANs will not
propagate to different IOS versions when extended VLANs are in use.
Answer: B
CISCO 300-115 EXAM QUESTIONS ANSWERS
Question: 7
Switch A, B, and C are trunked together and have been properly configured for VTP.
Switch C receives VLAN information from the VTP server Switch A, but Switch B does
not receive any VLAN information. What is the most probable cause of this behavior?
A. Switch B is configured in transparent mode.
B. Switch B is configured with an access port to Switch A, while Switch C is configured
with a trunk port to Switch B.
C. The VTP revision number of the Switch B is higher than that of Switch A.
D. The trunk between Switch A and Switch B is misconfigured.
Answer: A
CISCO 300-115 EXAM QUESTIONS ANSWERS
Question: 8
Switch A, B, and C are trunked together and have been properly
configured for VTP. Switch B has all VLANs, but Switch C is not receiving
traffic from certain VLANs. What would cause this issue?
A. A VTP authentication mismatch occurred between Switch A and
Switch B.
B. The VTP revision number of Switch B is higher than that of Switch A.
C. VTP pruning is configured globally on all switches and it removed
VLANs from the trunk interface that is connected to Switch C.
D. The trunk between Switch A and Switch B is misconfigured.
Answer: C
CISCO 300-115 EXAM QUESTIONS ANSWERS
Question: 9
How can the traffic that is mirrored out the GigabitEthernet0/48 port be limited to only
traffic that is received or transmitted in VLAN 10 on the GigabitEthernet0/1 port?
A. Change the configuration for GigabitEthernet0/48 so that it is a member of VLAN 10.
B. Add an access list to GigabitEthernet0/48 to filter out traffic that is not in VLAN 10.
C. Apply the monitor session filter globally to allow only traffic from VLAN 10.
D. Change the monitor session source to VLAN 10 instead of the physical interface.
Answer: C
DOWNLOAD YOUR CISCO 300-115
EXAM DUMPS WITH 100% PASSING
GUARANTEE AND GET FULL
REFUND.