8/8/2019 29 oct 2010
1/44
EXPERIMENTAL AND
ANALYTICAL STUDY OF COLDFORMED STEEL SECTIONS
SUBMITTED BY
AMITKUMAR ASHOK SONAWANE
M TECH STRUCTURES
GUIDED BY
PROF K.K.SANGALE
8/8/2019 29 oct 2010
2/44
`Hot rolled steel
`Cold formed steel
8/8/2019 29 oct 2010
3/44
` Hot Rolled steel1.Yielding starts at actual yield
value as the original material.2. Unit weight is comparatively
huge
3. More ductile innature.
4.Most of the time, we consider
only the global buckling of themember.
5. Applicationin Load bearing
structures, usually heavy load
bearing structures and where
ductility is more important (
Example Seismic prone areas)
6. Research is in advanced stages
` Cold Rolled steel1.The yield value is increased by15%-30% due to prework.
2. It is much smaller.
3. Less ductile
4. Local buckling, DistortionalBuckling, Global Buckling have to
be considered.5.Applicationin many variety ofloading cases.This includesbuilding frames, automobile,aircraft, home appliances, etc. Uselimited in cases where high
ductility requirements.
6.More possibilities as the conceptis relatively new and material findswide variety of applications.
8/8/2019 29 oct 2010
4/44
` Change in the mechanical properties of the
material by virtue of the cold working.
` Yield strength, and to a lesser extent the ultimatestrength, is increased as a result of this cold
working particularly in the bends of the section.
` Strength increase could reach 20% to 50%.
` The ductility of the steel is reduced as result .
8/8/2019 29 oct 2010
5/44
` The use of cold-formed steel members in buildingconstruction beganin the 1850s.
` first edition of the Specification for the Design of LightGage Steel Structural Members was published by AISI
in1946.( Allowable stress design(ASD) Specification)
` It was revised subsequently in1956, 1960, 1962, 1968,1980, and 1986 to reflect the technical developments.
` In1991, AISI published the first edition of the load
and resistance factor design Specification.` Both ASD and LRFD Specifications were combined
into a single specificationin1996
8/8/2019 29 oct 2010
6/44
` In2001, the first edition of the North American
Specification for the Design of Cold-Formed Steel
Structural Members was developed.
` It was revised and expanded in2007.` This updated specificationincludes new and revised
design provisions with the additions of the Direct
Strength Method inAppendix 1 and the Second-Order
Analysis of structural systems inAppendix 2.
8/8/2019 29 oct 2010
7/44
` Design standards and recommendations are now
available in Australia, Austria , Canada,
Czechoslovakia , Finland , France , Germany ,
India , Japan , The Netherlands, New Zealand ,The Peoples Republic of China , The Republic of
South Africa , Sweden , Romania , U.K. , U.S. ,
USSR.
8/8/2019 29 oct 2010
8/44
` Applications in residential and other low-rise
buildings.
` Factory assembly ofprefabricated units.
8/8/2019 29 oct 2010
9/44
8/8/2019 29 oct 2010
10/44
Author:Mahmood Md Tahir and Tan Cher Siang along with Shek Poi
Ngian
Proceedings of the 6th Asia-Pacific Structural Engineering and
Construction Conference (APSEC 2006), 5 6 September2006, Kuala
Lumpur, Malaysia
8/8/2019 29 oct 2010
11/44
` The Steel Technology Centre (STC), Universiti
Teknologi Malaysia has carried a ser ies of analytical
and exper imental research on cold-formed steelstructures. A series of research studies carried out in
UTM.
` Member capacities for lipped C-section and hat-
section.
` A full-scale test for roof truss system.
` Cold-formed steel tek-screw connection capacities.
8/8/2019 29 oct 2010
12/44
8/8/2019 29 oct 2010
13/44
8/8/2019 29 oct 2010
14/44
8/8/2019 29 oct 2010
15/44
8/8/2019 29 oct 2010
16/44
8/8/2019 29 oct 2010
17/44
8/8/2019 29 oct 2010
18/44
` Capacities of the proposed sections were ratio from
1.09- 2.21 compared to the design strength.
` The full-scale experimental test on roof truss alsoachieved two times of the estimated design capacities
` The tek-screw connection capacities in resistance to
shear force and pull-out force ranged 76%- 141%
higher than the design requirements.
8/8/2019 29 oct 2010
19/44
Author: DungM. Lue1, Ping-Tsung Chung, Jui-Ling Liu, and Chi-Ling
Pan
International Journal of Steel Structures
September2009, Vol 9, No 3, 231-240
8/8/2019 29 oct 2010
20/44
` The effective sectional area concept was adopted to
conduct the analysis.
` Study tested a total of21 channel specimens including
c-shaped cross-sections with and without web openings` Comparisons were made between the test results and
the predictions based on both the AISI standard and the
ANSYS analysis.
8/8/2019 29 oct 2010
21/44
1.Test specimen(65X45X10X1 mm & 92X45X10X1 mm)
8/8/2019 29 oct 2010
22/44
8/8/2019 29 oct 2010
23/44
Setup of test
8/8/2019 29 oct 2010
24/44
8/8/2019 29 oct 2010
25/44
8/8/2019 29 oct 2010
26/44
Test results
8/8/2019 29 oct 2010
27/44
` The shell element (shell 93) of 3D, 8-node, and
homogenous materials was used for the structural
analysis.
` This element was used to simulate a 3-d entitystructure, which has the buckling analysis feature.
` Material property: the basis of the materials tension
test, its youngs modulus is 130,250 mpa.Moreover, its
yielding stress is 198 mpa and its poisson ratio isassumed to be 0.3.
` It is necessary to employ the nonlinear analysis.
8/8/2019 29 oct 2010
28/44
8/8/2019 29 oct 2010
29/44
` The failure type of all specimens is observed and
identified as flexural-torsional buckling type.
` The experiment results indicated that the average
strength of specimen is slightly reduced caused bythe web openings.
` The average ratios of Ptest/PFEM prove that the FEM
is an efficient tool to predict the strength of
specimens.
8/8/2019 29 oct 2010
30/44
Author: B.W. Schafer*, T. Pekoz
Journal of Constructional Steel Research 47 (1998) 193210
8/8/2019 29 oct 2010
31/44
` Advanced computational modeling supplementsexperimental investigation.
` Accuracy of computational models relies significantlyon the characterization of selected inputs.
` No consensus exists on distributions or magnitudes tobe used for modelinggeometric imperfections and formodeling residual stresses of cold-formed steelmembers.
` Ideas are summarized in a preliminary set ofguidelinesfor computational modeling ofimperfections andresidual stresses.
8/8/2019 29 oct 2010
32/44
` Geometric imperfections refer to deviation of a
member from perfect geometry.
` Imperfections of a memberinclude bowing, warping,
and twisting as well as local deviations.` Local deviations are characterized by dents and regular
undulations in the plate.
8/8/2019 29 oct 2010
33/44
For type 2:
width/thickness
8/8/2019 29 oct 2010
34/44
` Computational modeling of residual stresses is
troublesome for analysts
` Residual stresses are often excluded altogether, or the
stressstrain behavior of the material is modified toapproximate the effect of residual stresses.
` Residual stresses are idealized as a summation of two
types: flexural and membrane.
8/8/2019 29 oct 2010
35/44
8/8/2019 29 oct 2010
36/44
` Characterization of geometric imperfections and
residual stresses in cold-formed steel members is
possible.
`
Existing data on imperfections provides a limitedbut useful characterization of imperfection
magnitude
` Data on residual stresses provide insight into
appropriate selection of distribution andmagnitude.
8/8/2019 29 oct 2010
37/44
Author: B.W. Schafer
Fifth International Conference on Coupled Instabilities in Metal
Structures
Sydney, Australia, 23-25 June, 2008
8/8/2019 29 oct 2010
38/44
` Summarize Research and experiences with
computational modeling of cold-formed steel at Johns
Hopkins University.
`
Explains the importance ofimperfections, residualstresses, boundary conditions, element choice, element
discretizationin collapse modeling of cold-formed steel
8/8/2019 29 oct 2010
39/44
` Ultimate strength and post-buckling mechanisms are
both imperfection sensitive
` Imperfections are a modeling convenience (the most
common approach) then the distributionis typically thefirst buckling mode, and the magnitude is either a
function of the plate thickness (i.E., 0.1t) or the plate
slenderness.
8/8/2019 29 oct 2010
40/44
` In conventional models where residual stresses are ignoredThe vonMises yield criteria with isotropic hardeningisused universally.
Boundary Conditions:` Boundary conditions have an majorimpact on cold-formed
steel collapse modeling.` Boundary conditions in cold-formed steel systems are never
as clean as in the computational model, and are usually farmore complicated than would exist in laboratory testing aswell.
8/8/2019 29 oct 2010
41/44
The use of quadratic elements (e.g., S9R5) instead of linear elements gives more
accuracy in results.
Also number ofintegration points
through the thickness of the element needs to be taken care of.
8/8/2019 29 oct 2010
42/44
` Collapse modelinggenerally requires the use of
material and geometric nonlinear finite element
analysis.
`
Solution sensitivities depend on solvers, element choiceand discretization, boundary conditions, material
models, initial imperfections, initial residual stresses.
8/8/2019 29 oct 2010
43/44
` The objective of this project is to carry out
experimentation on cold formed steel sections and
verify experimental results with analytical
methods(computational modeling)
` Experimentation and analysis will be done for
slotted angle sections.
` Software's to be used for analysis ANSYS and
ABAQUS.
8/8/2019 29 oct 2010
44/44
Top Related