7/29/2019 2011 Ford f150 Supercharger
1/41
Step 1
Disconnect negative terminal from
battery using 8 mm wrench.
Step 2
Drain cooling system by un-screwing the drain
plug on the passenger of the radiator. This is
best accessed through the fender well.
Attaching a length of 5/16 ID hose to the drain
nipple will help guide the coolant into the
container.
R Removing the coolant bottle cap
will aid in the draining of the coolant. Once
drained, replace the drain plug and the
coolant bottle cap.
7/29/2019 2011 Ford f150 Supercharger
2/41
Step 3Cover the tops of the fenders and the
bumper with protective wrap.
Step 4
Loosen screws on the band clamps on both ends of air intake duct. Remove PCV hose from air
intake duct. Remove break booster hose from air intake duct. Remove entire air intake duct
from engine.
jjkj
7/29/2019 2011 Ford f150 Supercharger
3/41
Step 5
Disconnect throttle body electrical connector.you will need to slide the red lock sideways first
in order to remove the connector.
Step 6
Disconnect purge valve electrical connector.
Step 7
Disconnect PCV hose connection at the
intake manifold.
7/29/2019 2011 Ford f150 Supercharger
4/41
Step 8
Disconnect heater hose connection on
drivers side of engine and move the hose
close to the battery, out of the way.
Step 9
Disconnect purge valve hose and hose
support and move hose out of way.
7/29/2019 2011 Ford f150 Supercharger
5/41
Step 10
Remove drives side fuel rail insulation.
Step 11
Remove passenger side fuel rail insulation.
Step 12
Disconnect brake booster hose connection.
7/29/2019 2011 Ford f150 Supercharger
6/41
Step 13
Disconnect fuel line connection at the fuel rail.
be careful to protect against fuel spray, as there
may be pressure in the fuel system.
Step 14
Remove the four bolts that secure the fuel
rail assembly to the intake manifold,
using a 10 mm socket.
Step 15
Disconnect the eight injector connector
from the injectors.
Step 16
Remove the fuel rail assembly with the injectors.
7/29/2019 2011 Ford f150 Supercharger
7/41
Step 17
Loosen the six intake manifold bolts
using an 8 mm socket.
Note: The bolts do not come out of
the intake manifold assembly.
Step 18
Remove intake manifold assembly from engine.
Step 19
Remove all eight injectors by first removing
the injector retaining clip with a screwdriver.
7/29/2019 2011 Ford f150 Supercharger
8/41
Step 20
Install new injectors using a small amount of
petroleum jelly to lubricate O-Rings.
Step 21
Re-install injector retainer clips.
Step 22
Install fuel rails as shown in photo,
pushing injectors down into seats.
7/29/2019 2011 Ford f150 Supercharger
9/41
Step 23
Install four M6 X 80 mm SHCS and M6
washer onto the injector bracket hole.
Step 24
Remove the eight intake seals from the
stock intake.
Step 25
Install the eight intake seals into the grooves
on the supercharger intake manifold.
7/29/2019 2011 Ford f150 Supercharger
10/41
Step 26Remove the four bolts retaining the throttle
body onto the stock intake using 8 mm socket.
Step 27
Remove the stock seal from the original
intake manifold using 8 mm socket.
Step 28
Remove the two bolts securing the purge valve
to the stock intake manifold using an 8 mm socket.
7/29/2019 2011 Ford f150 Supercharger
11/41
Step 29
Remove the bolt securing the PCV nipple to the
stock intake using an 8 mm socket.
Step 30
Using a utility knife, cut the plastic fuel
line, where it attaches to the steel line
at the firewall. Remove the plastic line.
Step 31
Cut the plastic line with a utility knife where
it attaches to the fuel rail connector, and
discard the plastic line.
7/29/2019 2011 Ford f150 Supercharger
12/41
Step 32
Connect the supplied 5/16 fuel line to the
fuel rail connector, and install the supplied
fuel hose clamp and tighten.
Step 33
Connect the other end of the supplied fuel
line to the steel fuel line at the firewall, and
install the supplied fuel hose clamp and
tighten.
Step 34
Remove the protective tape from
the rear of the supercharger.
7/29/2019 2011 Ford f150 Supercharger
13/41
Step 35
Install the supplied vacuum nipple to the
intake manifold using a small amount of
red threadlocker.
Step 36
Install the supplied O-Ring to the rear of the
supercharger. A small amount of petroleum
jelly may help in holding the O-Ring in place.
Step 37
Install the inlet elbow at the rear of the
supercharger.
7/29/2019 2011 Ford f150 Supercharger
14/41
Step 38
Install the three M8 X 25 SHCS and M8
washers and tighten.
Step 39
Install the M8 hex nut onto the stud and
tighten with a 13mm wrench.
Step 40
Install the PCV nipple and secure with the
supplied M6 X 16 SHCS and M6 washer.
7/29/2019 2011 Ford f150 Supercharger
15/41
Step 41
Connect supplied vacuum line to the
bypass valve nipple.
Step 42
Connect other end of vacuum line to the
nipple on upper rear of intake manifold.
Step 43
Installed supplied NPT elbow to inlet elbow
using a small amount of red thread locker.
7/29/2019 2011 Ford f150 Supercharger
16/41
Step 44
Install supplied brake booster hose nipple
onto the NPT elbow using a small amount
of red threadlocker.
Step 45
Install purge valve onto intake elbow with
original bolts using an 8 mm socket.
Step 46
Loosen the knock sensor bolts and adjust the rotation of the sensors to place them
as close as possible to the cylinder heads. It may be necessary to remove some of the
wire harness cover between the two sensors in order to rotate the sensors to the correct
location. Torque the sensors to 177 lb / in (20 Nm).
7/29/2019 2011 Ford f150 Supercharger
17/41
Step 47
Install the supercharger/intake manifold assembly onto the engine. This is a tight fit, so go
slowly. Once in place, the fuel rail bolts should start into the threaded holes on the cylinderheads.
Step 48
Tighten the four M6 X 80mm SHCS securing
the fuel rails, using an M4 allen socket.
7/29/2019 2011 Ford f150 Supercharger
18/41
Step 49
Install the six M6 X 40mm SHCS and M6 washers
into the intake manifold and tighten using an
M4 allen socket.
Step 50
Connect the eight fuel injector
electrical connectors.
Step 51
Remove the two thermostat housing bolts
using an 8mm socket.
7/29/2019 2011 Ford f150 Supercharger
19/41
Step 52
Remove the two water outlet housing
bolts using a 10mm socket.
Step 53
Remove the radiator hose from the
water outlet housing with
adjustable pliers.
Step 54
Remove the original hose clamp from the
radiator hose. The clamp is bonded to the
hose, so you must carefully cut the clamp
away from the hose.
7/29/2019 2011 Ford f150 Supercharger
20/41
Step 55
Install the hose onto the water outlet
housing, using the supplied HS24 hose
clamp. Note: How the hose sits
approximately inch further out
on the outlet housing.
Tighten clamp.
Step 56
Release tensioner with a Johnson
bar and a 15mm socket. Remove
the drive belt.
Step 57
Remove top water pump bolt using
a 10mm wrench.
7/29/2019 2011 Ford f150 Supercharger
21/41
Step 58
Remove water pump pulley bolts usinga 10mm socket. Remove pulley.
Step 59
Install supercharger belt idler pulley
and bracket using a 6mm allen socket.
Step 60
Re-install water pump pulley using
a 10mm socket.
7/29/2019 2011 Ford f150 Supercharger
22/41
Step 61
Install supercharger drive belt
per diagram.
Step 62Install O-Ring on water pump outlet
spacer using a small amount of
petroleum jelly to hold the O-Ring
in place during assembly.
Step 63
Install spacer between water pump outlet
and water pump with the O-Ring towards
the engine using the M6 X 75mm SHCS and
6mm washers. Tighten with 4mm allen
socket.
7/29/2019 2011 Ford f150 Supercharger
23/41
Step 64
Re-install water outlet housing to drivers
side cylinder head using 10mm socket.
Check for adequate clearance between
radiator hoses and supercharger drive
belt.
Step 65
Re-connect heater hose to drivers
side head, routing the hose over
the supercharger.
Step 66
Remove passenger side PCV hose from
valve cover and cut tube on both ends
to enable hose to be removed from thefittings.
7/29/2019 2011 Ford f150 Supercharger
24/41
Step 67
Push PCV fittings onto each end of supplied
5/8 ID hose. Install heat shrink bands to
secure hose ends using a heat gun to shrink
the bands into place.
Step 68
Install one end of PCV hose onto nipple
on passenger valve cover and installother end onto PCV nipple located on
supercharger inlet elbow.
Step 69
Install original throttle body seal into
groove in supercharger inlet elbow.
7/29/2019 2011 Ford f150 Supercharger
25/41
Step 70
Install throttle body onto inlet elbow
using original bolts and an 8mm socket.
Step 71
Cut brake booster hose to shorten
length in order to connect to barb
fitting on supercharger inlet elbow.
Step 72
Push hose onto barb and retain using
original clamp.
7/29/2019 2011 Ford f150 Supercharger
26/41
Step 73
Cut hose at end of purge valve line,
in order to remove purge valve fitting.
Step 74
Cut purge valve hose shorter and
connect purge valve fitting. Connect
purge valve line to purge valve.
Step 75
Cut throttle body wiring approx. 6 inches
back from connector.
7/29/2019 2011 Ford f150 Supercharger
27/41
Step 76
Cut purge valve wiring approx. 6 inches
back from connector.
Step 77
Use supplied wiring extensions and
connectors to lengthen the throttle
body harness and the purge valve
harness.
Step 78
Use supplied split loom to cover wiring
once extensions have been spliced in.
7/29/2019 2011 Ford f150 Supercharger
28/41
Step 79
Route wiring for throttle body and purge valve down passenger side valve cover,
around rear of supercharger and connect each to proper connector. Secure wiring
loom with supplied tie wraps.
Step 80
Connect intake sensor harness suppliedto the IAT sensor on the rear of the
supercharger intake.
Step 81
Route the wiring towards the air filter
box. Connect the blue wire from the
mass air flow sensor wire harness using
the supplied scotchlock connector.
7/29/2019 2011 Ford f150 Supercharger
29/41
Step 82
Cut the purple wire in the mass air flow sensor
wire harness and connect the purple wire from
the intake air sensor harness to the purple
wire on the wire harness. Seal the harness with
supplied electrical tape. Cover wiring with
supplied split loom and secure harness with
supplied tie wraps.
Step 83
Install air inlet ducts and tubing connectors as shown in photos. Attach with supplied
HS56 hose clamps and tighten with screwdriver.
Step 84
Connect supplied 5/8 PCV hose to two
supplied PCV connectors as shown in
photo.
7/29/2019 2011 Ford f150 Supercharger
30/41
Step 85 (no photo)
Use supplied heat shrink tubing to Step 86 photo
secure PCV hose to connectors.
Step 86
Install completed PCV hose assembly as
shown in photo.
Step 87
Install intercooler water pump onto heat
exchanger as shown in photo using
supplied HS36 hose clump. Tighten
clamp with a screwdriver.
Step 88
Cut approx. 2 inches off short leg of
supplied hose.
7/29/2019 2011 Ford f150 Supercharger
31/41
Step 89
Install hose as shown in photo using supplied
HS12 hose clamps. Tighten clamps with a
screwdriver.
Step 90
Remove two upper front bumper bracket
bolts using 13/16 socket.
Step 91
Remove horn bracket mounting bolt using
10mm socket.
7/29/2019 2011 Ford f150 Supercharger
32/41
Step 92
Bolt heat exchanger to upper radiator (no photo)
support using the original bolt and a
10mm socket.
Step 93
Drill 3/16 hole in upper radiator support
being careful to ensure the heat
exchanger is level.
Step 94
Use supplied X 1 self tapping screw
and fender washer to mount drivers
side upper strap to radiator support using
an 11mm socket.
7/29/2019 2011 Ford f150 Supercharger
33/41
Step 95
Tighten original upper bumper nuts
to secure lower heat exchanger
brackets using 13/16 socket.
Step 96
Photo shows installed heat exchanger.
Step 97
Bolt horn bracket on to passenger side
upper heat exchanger bracket using
supplied X 1 bolt, nylock nut and
washers with an 11mm socket.
7/29/2019 2011 Ford f150 Supercharger
34/41
Step 98
Drill holes into radiator shroud using
3/16 drill bit to mount intercooler
bottle bracket.
Step 99
Rivet bracket in place using 3/16
supplied rivets.
Step 100
Bolt bottle to bracket using M6 X 25
bolt and washer.
7/29/2019 2011 Ford f150 Supercharger
35/41
Step 101
Cut a 30 inch length of hose from the supplied hose, connect one end of hose
to lower nipple of intercooler bottle and the other end to intercooler pump.
Secure with supplied HS12 hose clamps and tighten with screwdriver.
Step 102
Cut an 18 inch length of hose and a 3 inch length of hose from the supplied hose.
Connect one end to upper nipple of intercooler bottle and the other end to the 90 degree
fitting. The 3 inch hose connects the other side of the 90 degree fitting to the vertical
intercooler nipple on the front of the intake manifold. Use supplied HS12 hose clamps to
secure the hoses. Tighten with a screwdriver.
7/29/2019 2011 Ford f150 Supercharger
36/41
Step 103
Cut a 32 inch length of hose and a 3 inch length of hose and a 6 inch length of hose
from the supplied hose. Connect the 3 inch piece on one end of the 32 inch hose using a
supplied 90 degree fitting and the 6 inch piece on the other end of the 32 inch hose. Connect
the 6 inch hose to the lower heat exchanger nipple and the 32 inch hose through the radiator
support to route. Connect the 3 inch hose to the 45 degree intercooler nipple located at thescrewdriver.
Step 104
Using a trim tool, remove the upper
radiator support trim panel.
7/29/2019 2011 Ford f150 Supercharger
37/41
Step 105
Drill a 3/16 hole in the passenger side
fuse box bracket next to the hole for
the trim clip.
Step 106
Attach the relay using the supplied
3/16 rivet.
Step 107
Connect the 10 gauge red wire with the
male spade connector to the lower left
pin in cavity 9.
7/29/2019 2011 Ford f150 Supercharger
38/41
Step 108
Connect the ring terminal of the 10 gauge
red wire to the positive terminal inside
the fuse box. Tighten nut with a 10mm
socket.
Step 109
Connect ground wire ring terminal to
negative terminal of battery cable
using a 10 mm socket.
Step 110
Connect water pump electrical connector
to the water pump and route wiring close
to radiator support. Use tie wraps tosecure wiring.
7/29/2019 2011 Ford f150 Supercharger
39/41
Step 111
Re-install upper radiator support
trim panel using original trim clips.
Step 112
Connect negative terminal to battery,
tighten with 8mm socket.
Step 113
Connect handheld programmer to OBD connector under dash. Follow directions on
programmer to install custom tune. Ensure battery is fully charged before starting download.
7/29/2019 2011 Ford f150 Supercharger
40/41
Step 114
Fill radiator bottle with 50/50 mixture
of Ford antifreeze and water.
Step 115
Fill intercooler bottle with 50/50 mixture of Ford antifreeze and water. Turn ignition key to
run position and verify that the coolant is circulating through bottle.
Step 116
Fill truck with 91 octane fuel. Start engine and warm up truck fully. Check fluid levels.
7/29/2019 2011 Ford f150 Supercharger
41/41
Top Related