8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 1/96
Dishwasher Training – 2011
New Door Configuration2011 E - Star
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 2/96
2
Updates Front Control Models
• 2011 E-star w/ enhanced control.
• Locking connectors on control/harnesses.
• Upper rack slides improved to wheels on rails.
• Revised tines spacing in upper/lower racks.
New Product Top Controls on Plastic Tubs
• Top controls – new console and tactile UI for control.
• Locking connectors on harnesses.
• Pocket handle and towel bar handle models.
• Racking improvements – upper rack slides + tine spacing improvements.
• Gray tubs and inner doors .
New Product Entry level Top Controls on SS Tubs
• Top controls – new console and tactile UI (same as above)
• Limited pocket handle models.
Current front control
New pocket handle top control
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 3/96
3 7/28/2011
IMPORTANT SAFETY NOTICE
The information in this presentation is intended for use by individualspossessing adequate backgrounds of electrical, electronic, & mechanicalexperience. Any attempt to repair a major appliance may result in
personal injury & property damage. The manufacturer or seller cannot beresponsible for the interpretation of this information, nor can it assumeany liability in connection with its use.
WARNING
To avoid personal injury, disconnect power before servicing this product.
If electrical power is required for diagnosis or test purposes, disconnectthe power immediately after performing the necessary checks.
RECONNECT ALL GROUNDING DEVICES
If grounding wires, screws, straps, clips, nuts, or washers used to
completea path to ground are removed for service, they must be returned to theiroriginal position & properly fastened.
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 4/96
4 7/28/2011
GE Factory Service Employees are required to use safety glasses with side
shields, safety gloves steel toe shoes for all repairs.
Dyneema® CutResistant Glove
Steel Toe Shoes Plano Safety Glasses
VR Gloves – provide shock protection
Prescription Safety Glasses
Safety Glasses
must be
compliant with
ANSI Z87.1-2003
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 5/96
5 7/28/2011
Front Control
Top Control
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 6/96
6
7/28/2011
New Door componentsTactile Control Buttons, Vent, Pocket Door Handle and
Front Light Indicator Lens
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 7/96
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 8/96
8
7/28/2011
Cycles and Times (Top Control):
Auto**: 5-7 gallons* 49-133 minutes*
Sanitize: 8.8-11.8 gallons* 50-279 minutes*
Normal: 3.3-8.3 gallons* 54-143 minutes*
Light: 7.6-10.5 gallons* 46-88 Minutes*
*Min = low soil
Max = high soil and all options selected
35 minute heated dry in Normal Wash
45 minute dry in Auto, Sanitize and Light Wash
Steam Option adds 15 minutes to cycle
**Some models do not have an Auto Cycle
Use and Care shows Minimum Times. No Enhancements
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 9/96
9
7/28/2011
Cycles and Times (Front Control):
Pots Pans or Heavy**:
11.8 gallons 88 minutes (Timed cycle)
Sanitize**: 8.8-11.8 gallons* 50-279 minutes*
Normal: 3.3-8.3 gallons* 54-143 minutes*
Light**:
7.6-10.5 gallons* 46-88 Minutes*
China Crystal**:
9.2 gallons 41 minutes (Timed Cycle)
Rinsed Only**: 1.2 gallons 7 minutes
*Min = low soil
Max = high soil and all options selected
35 minute heated dry in Normal Wash
45 minute dry in Auto, Sanitize and Light Wash
Steam Option adds 15 minutes to cycle
**Some models do not have an this Cycle
Use and Care shows Minimum Times. No Enhancements
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 10/96
10 7/28/2011
Cycle Time Definition Normal or Auto Cycles with allHeat Options selected (times and cycles change
depending on Turbidity Sensor readings)Pre- Pre- Pre- Steam Steam Pre- Pre- Main Post Post FinalWash Wash Wash Wash Wash Wash Wash Wash Rinse
Water Valve (seconds) 63 17 17 63 21 63 21 21 63 23 23Circulation (minutes) 5 5 5 15 2 10 15 30 2 3 10Heater (minutes) 17 7 10 15 30 8 5Drain (seconds 7 7 75 10 75 10 10 75 11 11 105
35 minute heated dry in Normal Wash45 minute dry in Auto,
Note: depending on Turbidity Response, it is possible the cycle could skipfrom the first Pre-Wash to the Main Wash and then to Final Rinse.
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 11/96
11 7/28/2011
Mini Manual Location - Plastic Tub
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 12/96
12 7/28/2011
Passive Vent, No Fan or damper
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 13/96
13 7/28/2011
Indicator Lamp Lens
Solid Amber when running, Solid Green when Clean
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 14/96
14 7/28/2011
Improved Racks, Rollers and Tracks, Plastic tub
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 15/96
15 7/28/2011
New rollers on Rack
New end caps, notice new tab
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 16/96
16 7/28/2011
Push Tabto centerto remove
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 17/96
17 7/28/2011
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 18/96
187/28/2011
Track, Rear Cap and Roller / Stud on tub
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 19/96
197/28/2011
Door Strike / Catch is non adjustable
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 20/96
207/28/2011
Tub TCO location
1 shot with Manual reset Trip at 189 with manual reset
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 21/96
217/28/2011
Tub TCO is resettable, if tripped, Reset TCO &replace the control
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 22/96
227/28/2011
Fill hose should be inserted 1 1/2 inches
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 23/96
23
7/28/2011
Fill Funnel, inside tub
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 24/96
24
7/28/2011
Rotate Clockwise to remove
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 25/96
25
7/28/2011
Fill funnel seal
seal
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 26/96
26
7/28/2011
Turn Counterclockwise and lift to remove wash arm
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 27/96
27
7/28/2011
Coarse Filter
Fine Filter
Hub Nut
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 28/96
28
7/28/2011
Remove nut to remove Fine Filter
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 29/96
29
7/28/2011
Lift Fine Filter to remove
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 30/96
30
7/28/2011
To remove Top Wash Arm and Conduit, remove¼” Hex screw
Conduit
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 31/96
31
7/28/2011
Lift Tab, continue to remove Conduit
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 32/96
32
7/28/2011
Push Conduit back and to side to finish removal,being careful to not break tab.
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 33/96
33
7/28/2011
To remove Sump Cover push in 4 tabs and lift cover
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 34/96
34
7/28/2011
To Remove sump filter, the tabs can be released with ascrewdriver or putty knife
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 35/96
35
7/28/2011
Push Sump Filter to right and lift to remove
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 36/96
36
7/28/2011
Tab location for cover and filter removal
Cover tabs
Sump Tabs
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 37/96
37
7/28/2011
To remove the wash arm hub or support, twistcounterclockwise. It will make a snap noise when the locator
tab on the tub breaks (this is normal).
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 38/96
38
7/28/2011
With hub removed, Coarse Filter can now be removed
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 39/96
39
7/28/2011
Coarse Filter removal.
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 40/96
40
7/28/2011
Proper location of the Wash Arm Bearing or ThrustWasher
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 41/96
41
7/28/2011
Make sure the Bearing or Thrust Washer is in placewhen re-assembled.
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 42/96
42
7/28/2011
Overfill System will only cut voltage to Water Valve.To remove cover, unscrew ¼” Screw and lift Cover
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 43/96
43
7/28/2011
Float Dome, to remove, simply lift
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 44/96
44
7/28/2011
Float Stem activates Flood Switch below.
I d l2 screws at bottom of door
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 45/96
45
7/28/2011
Inner door removal
2 machine screws located at hinge
6 screws top part of inner door
New Door Components
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 46/96
46
7/28/2011
New Door Components;
Inner DoorOuter Door
Tactile SwitchesVentingLocking Connectors
Passive Vent
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 47/96
47
7/28/2011
New Top Control Inner Door configuration
Console
Vent TactileSwitch
Vinyl Shield
Cover
Door Switch Assembly
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 48/96
48
7/28/2011
Vinyl Shield will only have to be removed if console isreplaced, it can be folded up to access control.
Vinyl Shield MUST be in place.
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 49/96
49
7/28/2011
Shield folded back to show control TCO, locatedon cover
1 shot Trip at 280
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 50/96
50
7/28/2011
Control TCO is one shot, If tripped, look for control,connector wire damage. Replace damaged components.
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 51/96
51
7/28/2011
Cover removal, 1. lift top and pull out, 2. pushbottom down
1.
2.
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 52/96
52
7/28/2011
To remove control board, remove 1 screw in center ofboard and release tabs. Notice locking connectors.
Tabs Screw
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 53/96
53
7/28/2011
Model Select MUST be Transferred or newcontrol will not operate, just flash
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 54/96
54
7/28/2011
Insulator between control board and console,Must be installed
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 55/96
55
7/28/2011
Pocket Handle has 4 screws, control board mustbe removed to access screw under control.
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 56/96
56
7/28/2011
Handle can now be removed from the front
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 57/96
57
7/28/2011
Tactile switch has 2 screws securing switch toconsole
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 58/96
58
7/28/2011
Switch has a silicone pad to protect frommoisture and buttons. Wire harness must be
removed from control board.
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 59/96
59
7/28/2011
Buttons and Silicone Pad come as an assembly
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 60/96
60
7/28/2011
Notice buttons are keyed, they fit one way
Indicator light on front panel Solid Amber when unit is
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 61/96
61
7/28/2011
Indicator light on front panel. Solid Amber when unit isoperating, Solid Green when cycle ended and dishes
are clean
To Remove Door Switch assembly
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 62/96
62
7/28/2011
To Remove Door Switch assembly,unscrew 2 screws, Insulator MUST be used
Door Switch Assembly held in place with bracket and 2
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 63/96
63
7/28/2011
Door Switch Assembly held in place with bracket and 2screws. Insulator must be in place (previous slide)
Door Switch comes as an assembly 2 switches and
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 64/96
64
7/28/2011
Door Switch comes as an assembly, 2 switches andbracket / actuator
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 65/96
65
7/28/2011
When replacing Front Panel, Console or Light Lens, theVent will have to be removed and replaced
(double back tape cannot be reused)New vent will come with Console and Lens as a Kit
vent
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 66/96
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 67/96
67
7/28/2011
Remove any excess adhesive from the outer door
Disposeold vent
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 68/96
68
7/28/2011
Install new vent on clean panel
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 69/96
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 70/96
70
7/28/2011
Console removed
Lens
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 71/96
717/28/2011
Lens
Adhered with doubleback tape
Console must be removedto access lens
WASHABILITY COMPLAINTS1 Level DW left to right and front to back
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 72/96
727/28/2011
1. Level DW left to right and front to back.
2. Verify presence of air gap or high drain loop.
3. Confirm lower spray arm thrust washer is installed
4. Confirm spray arms spin freely.
5. Confirm spray arm jets are clear.
6. Confirm no breaches, tears or clogs in fine filter under the bottom spray arm. Clean if necessary.
7. Confirm coarse filter clean and seated with no gaps (not warped).
8. Remove cover inlet and sump filter.
9. Remove any debris from sump.
10. Reinstall sump filter and cover.
11. Confirm Calrod is operating properly. If not, check connections and TCO. If TCO is open,
suspect control problem.12. Close detergent cup and use Service Mode to verify the lid opens.
13. Inlet water temperature should be at least 120 degrees F.
14. Turn on dishwasher and fill; check for correct water level
15. Test water hardness with WD01X10295 or WX5X370 test strip. Adjust detergent use
accordingly. Refer to Owner's Manual.
16. Use a highly rated detergent: generally detergent tablets or packs work best. Refer to Owner's
Manual.17. Use a rinse agent.
18. Load dishwasher per Owner's Manual.19. Select cycles and options according to the soil level. Refer to Owner's Manual.
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 73/96
737/28/2011
Correct water levelMain wash is suggested time to check for proper level.
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 74/96
747/28/2011
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 75/96
757/28/2011
Schematic
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 76/96
767/28/2011
Schematic
Control replacement / Calibration
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 77/96
777/28/2011
The dishwasher will enter into the TEST/
CALIBRATION mode at first power-up.
The door must be closed and latched.
WAIT until the second fill (approximately6 minutes from power-up) to cancel cycle
by pressing the Start/Reset pad.
The dishwasher will be ready to operate
after the pump out.
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 78/96
787/28/2011
SS units have different Racking andInner Door Vent
Tactile Switch Assembly and Vent on outer
door is the same as on Plastic Tub
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 79/96
79 7/28/2011
Mini Manual Location - Stainless Tub
Tub TCO is located Front Center behind cross member
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 80/96
807/28/2011
Tub TCO is located Front Center behind cross member.If it is open, replace the control.
TCO
Trips at 165, auto reset at 150
SS Upper rack - slide
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 81/96
817/28/2011
Upper rack extended outward Front view with rack pushed in.
NOTE: Removing front end caps
will not release rack
Upper rack - slide
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 82/96
827/28/2011
To remove upper rack assembly, press “down” to disengage lever on left side
and “up” on the right side.
(Right side)
Pull rack assembly forward and out
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 83/96
837/28/2011
Door catch is non-adjustable
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 84/96
847/28/2011
Door separated, there are no hangers to balance thedoor as on previous models.
Inner door componentsC ff
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 85/96
857/28/2011
Vent, Control cover and door switch different,compared to plastic tub
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 86/96
867/28/2011
Console Component ViewTo remove Console, Handle and Vent must be
removed
Handle ScrewsVent
Door Switch
TCO
Control and cover
Tactile Switch
1 shot Trip at 280
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 87/96
877/28/2011
Single door switch, breaks line side
Vent on SS units is different than Plastic Tubs
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 88/96
887/28/2011
Vent on SS units is different than Plastic Tubs.Correct install is critical for proper operation.
It is possible to install the vent incorrectly!
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 89/96
897/28/2011
The vent is keyed, but in the middle.The vent can be installed incorrectly.
SS Vent correctly installed
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 90/96
907/28/2011
Correct positioning
Incorrect position, no airflow = no dry / poor dry and leaks out bottom of door
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 91/96
917/28/2011
Incorrect position
WASHABILITY COMPLAINTS1. Level DW left to right and front to back.
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 92/96
927/28/2011
2. Verify presence of air gap or high drain loop.
3. Confirm lower spray arm thrust washer is installed
4. Confirm spray arms spin freely.
5. Confirm spray arm jets are clear.
6. Confirm no breaches, tears or clogs in fine filter under the bottom spray arm. Clean if necessary.7. Confirm coarse filter clean and seated with no gaps
8. Remove cover inlet and sump filter.
9. Remove any debris from sump.
10. Reinstall sump filter and cover.
11. Confirm Calrod is operating properly. If not, check connections and TCO. If TCO is open,
suspect control problem.12. Close detergent cup and use Service Mode to verify the lid opens.
13. Inlet water temperature should be at least 120 degrees F.
14. Turn on dishwasher and fill; check for correct water level
15. Test water hardness with WD01X10295 or WX5X370 test strip. Adjust detergent use
accordingly. Refer to Owner's Manual.
16. Use a highly rated detergent: generally detergent tablets or packs work best. Refer to Owner's
Manual.17. Use a rinse agent.
18. Load dishwasher per Owner's Manual.19. Select cycles and options according to the soil level. Refer to Owner's Manual.
Correct water levelMain wash is suggested time to check for proper level.
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 93/96
937/28/2011
gg p p1st fill is 63 seconds, there is a partial drain and fill before
main wash.
Service Mode SS
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 94/96
94 7/28/2011
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 95/96
8/9/2019 2011 E Star GE Dishwasher Training - 2011 New Door Configuration
http://slidepdf.com/reader/full/2011-e-star-ge-dishwasher-training-2011-new-door-configuration 96/96
Top Related