7/25/2019 000 Round Trip Time Calculations
1/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 1 of 24
Chapter 3Elevator Traffic Analysis and Design
(Revision 9.0, 9/3/2011)
1. Summary of the Traffic Analysis and Design StepsThe following steps have to be followed in the elevator traffic analysis and designprocedure.
1) Inputs: The input parameters needed in order to carry out the traffic analysis for abuilding are as follows:
a) Type of building (office, residential, hotel, hospital, shopping centre.....etc).b) Number of floors above ground.c) Floor heights.d) Net areas for each floor.
e) In certain cases the client might specify the required interval and theexpected arrival rate.
2) Analysis: The designer will then carry out the following:
a. Find the recommended speed based on dividing the total travel by 20 andfinding the nearest preferred speed value.
b. Set the suitable values of jerk and acceleration depending on the type oftraffic in the type of building given (e.g., for a hospital, select low values ofacceleration and jerk).
c. If not set by the client, deciding on the suitable arrival rate for the type oftraffic in the type of building given.
d. If not set by the client, deciding on the suitable interval for the type of trafficin the type of building given.
e. Decide on a starting number of lifts.f. Decide on a starting capacity for the lifts.g. Carry out the traffic analysis that provides the required interval at the
expected arrival rate.h. Change the number of lifts up or down until the required interval is
achieved.i. Once the interval is achieved, fix the number of lifts.
j. If it is not possible to find a suitable solution using a maximum number of10 lifts then investigate zoning the building into two or three zones ifneeded.
k. Depending on the car loading percentage, reduce the capacity of the liftsused until the loading percentage is near 80%.
l. Select the suitable number, speed and capacity of the goods lift required.m. Select the suitable number of fie fighting lifts, using the 60 second rule to
decide on the speed of the lifts.
3) Outputs: The aim of the traffic is to find the following parameters:
a) Speed of the lifts.b) Number of lifts.
7/25/2019 000 Round Trip Time Calculations
2/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 2 of 24
c) Capacity of the lifts.d) Zoning if required.e) Goods lift requirements.f) Fire fighting lifts requirements.
2. Legend is the round trip time in sint is the interval at the main terminal in sL is the number of the elevators in the groupU is the total building populationUiis the building population on the i
thfloorHC% is the handling capacity expressed as a percentage of the building population
in five minutesAR% is the passenger arrivals expressed as a percentage of the building population
in the busiest five minutes
N is the number of floors above the main terminalHis the highest reversal floor (where floors are numbered 0, 1, 2.NS is the probable number of stopsdfis the typical height of one floor in mvis the top rated speed in m/sais the top acceleration in m/s
2
jis the top rated speed in m/s3tfis the time taken to complete a one floor journey in s assuming that the lift attains
the top speed vCC is the car carrying capacity in personsPis the number of passengers in the car when it leaves the ground (does not need to
be an integer)dGis the height of the ground in m where more than the typical floor heighttdois the door opening time in stdcis the door closing time in stsdis the motor start delay in stao is the door advance opening time in s (where the door starts opening before the
car comes to a complete standstill)tpiis the passenger boarding time in stpois the passenger alighting time in s
3.0 Introduction
The round trip time ( ): The round trip time is defined as the time taken for theelevator to pick up the passengers from the main lobby, travel to the upper floors anddeliver the passengers to their destinations and then express back to the mainterminal again to pick up more passengers.
must be measured between one event and exactly the following event. Forexample it could be measured between the doors starting to open at the mainterminal until they start re-opening again at the main terminal.
The highest floor that the elevator reaches in one round trip is called the highestreversal floor, H. It can be less than or equal to N, the number of floor above themain terminal. It does not need to be an integer.
The number of stops that the elevator makes in one round trip is called theprobable number of stops, S. It can be less than or equal to the number ofpassengers in the car, P. It does not need to be an integer.
7/25/2019 000 Round Trip Time Calculations
3/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 3 of 24
When more than one lift is present in the same group, then ideally they have to bespread evenly. The interval is the time between the arrivals of the lift in the mainterminal. The interval is obtained by dividing the round trip time by the number ofelevators in the same group. Thus the interval can be improved either by increasingthe number of elevators or reducing the round trip time. The round trip time can bereduced by increasing the speed or reducing the number of stops or reducing thehighest reversal floor.
The various parameters used in the elevator traffic analysis are shown in the tablebelow:
7/25/2019 000 Round Trip Time Calculations
4/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 4 of 24
Parameter DefinitionTypical valuesor comments
The round trip time
The average time taken by the elevator to do acomplete cycle in the building during up peak
conditions (pick up passengers from the mainterminal, travel to the upper floors and thenexpress back to the main terminal again)
int The intervalThe average time between successive arrivals of
elevators in the main terminal30 s
LNumber of elevators in
the same groupNumber of elevators in the same group 2 to 8
U Population Total building population
HC% The handling capacityThe percentage of the building population
transported in five minutes
AR% The arrival rateThe passenger arrivals expressed as a percentageof the building population in the busiest five minutes
N Number of floors The number of floors above the main terminal
Note that the
total number offloors is N+1
(when the mainterminal isincluded)
HThe highest reversal
floor
Highest reversal floor (where floors are numbered0, 1, 2.N) NH
CC Car carrying capacityThe car carrying capacity in persons. This is
theoretical capacity of the car.
P Passengers in the carThe number of passengers in the car when it leavesthe main terminal (does not need to be an integer).
This is the effective capacity of the carCCP 8.0
SThe probable number
of stops
Probable number of stops the that elevator willmake in one round trip PS
df Floor to floor heightThe typical height of one floor in m (finished floor
level to finished floor level, FFL to FFL)
No need toenter this value
for the topmost floor
4 m
v Speed The rated speed in m/s
a Acceleration The top acceleration in m/s 1
j Jerk The top rated speed in m/s3 0.5 to 1.5
tf One floor cycle timeThe time taken to complete a one floor journey in s
assuming that the lift attains the top speed v
dG Main terminal heightthe height of the main terminal in m where more
than the typical floor height5 m
tdo Door opening timeThe door opening time in s
2 s
tdc Door closing timeThe door closing time in s
3 s
tsd Motor start delayThe motor start delay in s
0.5 s
taoAdvance door opening
time
The door advance opening time in s (where thedoor starts opening before the car comes to a
complete standstill)
Do not use onsafety grounds
tpiPassenger boarding
timeThe passenger boarding time in s 1 to 1.2 s
tpoPassenger alighting
timeThe passenger alighting time in s 1 to 1.2 s
7/25/2019 000 Round Trip Time Calculations
5/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 5 of 24
4. Number of passengersIt is accepted in practice that the car does not fill up completely. In general it only fillsup to 80% of the car carrying capacity.
CCP %80
5. The Probable Number of StopsThe probable number of stops S is the average number of stops that the elevatormakes in one round trip journey
P
N
111NS
for equal floor populations
N
1i
P
i
U
U1NS
for unequal floor populations where Uiis the
population of floor iand Uis the total buildingpopulation.
6. The Highest Reversal FloorThe highest reversal floor H is the highest floor that the lift reaches in a round tripjourney.
P1N
1i N
iNH
for equal floor populations
1N
1j
Pj
1i
i
UUNH for unequal floor populations where Uiis the floorpopulation of floor iand Uis the total building
population.
7. The Round Trip Time EquationIn this section, the equation for the round trip time equation is derived from firstprinciples. It makes the following assumption:
1. The traffic is pure incoming traffic (up peak only). All passengers arrive at theentrance and board the elevator to go to his/her destination on one of the
upper floors.
2. In one trip time, the elevator makes Sstops and reaches Hhighest reversalfloor. These two variables have been derived elsewhere. They depend on thenumber of floors above the main entrance (the lobby), N, and on the numberof passengers in the car, P. They can be derived for the general case wherethe floor populations are unequal or for the special case where the floorpopulations are equal.
3. The elevator collects P passengers from the main terminal (lobby) anddelivers them to their selected destinations. It then expresses back to the
main terminal to pick another set of Ppassengers.
7/25/2019 000 Round Trip Time Calculations
6/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 6 of 24
4. Every time the elevators stops at a floor, it takes time for the doors to open,the passengers to transfer (in at the main terminal and out at the destinationfloors) and then for the doors to close. Further delay at each stop is causedby the start delay of the motor. The delay will be reduced in the case ofadvanced door opening.
5. The assumption will be made that the elevator will attain its top speed in onefloor journey.
6. The assumption will also be made that the floor heights are equal.
7. The assumption will also be made that there is only one entrance floor (arrivalfloor). All passengers arrive through this single entrance.
The round trip time is made up of main three parts: the time spent at the ground floor
collecting passengers, the time spent travelling to the upper floors and deliveringpassengers to their destination, and the third part is the express travel back from thehighest reversal back to the main terminal.
taccis the time taken to accelerate up to the top speed from standstill in stdecis the time taken to decelerate down from the top speed down to standstill in s
HSMT
Where:
MT is the time spent at the main terminal in s
S is the time spent travelling to the upper destination floors and delivering the
passengers in s
H is the time spent expressing back to the main terminal from the highest reversal
floor in s
The time spent at the main terminal involves the opening of the door, the transfer ofP passengers into the car and the closing of the door, in addition to the start delayminus the advanced door opening.
piaosddcdoMT tPtttt
poaosddcdodecacc
fff
poaosddcdodecacc
f
poaosddcdo
f
decaccS
tPttttttv
d
v
dS
v
dH
tPttttttSv
dH
tPttttSv
dHttS
But
7/25/2019 000 Round Trip Time Calculations
7/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 7 of 24
j
a
a
v
v
dttttt
v
dt
f
decaccvdecacc
f
f
poaosddcdof
f
f
S tPttttv
d
tSv
d
H
The third part of the round trip time equation is the time taken to travel back from thehighest reversal floor express back to the main terminal:
v
dt
v
dH
j
a
a
v
v
dH
j
a
a
v
v
dH
f
f
f
f
f
H
Adding all the three elements together gives:
popiaosddcdof
f
f
f
f
f
poaosddcdo
f
f
f
piaosddcdo
HSMT
ttPttttv
dtS
v
dH
vdt
vdH
tPttttv
dtS
v
dHtPtttt
12
The equation for the round trip time (RTT) can be written as follows:
v
ddttPtttt
v
dtS
v
dH
fG
popiaosddcdo
f
f
f212
Note that the last term has been added to the case where the main terminal (thelobby) has a floor height that is more than the typical floor height. As this distance iscovered in both the up and down directions, it has been multiplied by 2. dG is theheight of the main terminal floor.
In general for most buildings (especially office buildings) the main terminal orthe lobby has a height greater than the typical floor height, usually for aestheticreasons but sometimes for functional reasons as well.
8. The Handling CapacityThe handling capacity is the percentage of the building population that can be movedin five minutes.
7/25/2019 000 Round Trip Time Calculations
8/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 8 of 24
U
PLHC
300%
9. The Interval
The interval is the average time between the arrivals of consecutive elevators in themain terminal.
Lint
11. Kinematic EquationsThe time t taken to complete a journey of distance d, with a top speed of v, topacceleration a,and top jerk jcan be calculated as follows under the three differentconditions:
If
aj
jvvad
22
then j
a
a
v
v
d
t
If
aj
jvvad
j
a2 22
2
3
then
2
j
a
a
d4
j
at
If2
3
j
a2d then
3
1
j
d32t
12. Mathematical Proof the Probable Number of Stops for Equal floorPopulationStarting from first principles, derive an expression for the probable number of stops(S) and the probable highest reversal floor (H) that a lift will make in a round tripjourney during up peak (incoming traffic).
Under up peak (incoming traffic) conditions, the lift will fill up with passengers atthe ground floor, and then deliver the passengers to their destinations in the upperfloors. It then expresses back to the ground floor to collect more passengers and soon.
The car has a capacity CC, but only fills up to P passengers. The number offloors above ground is denoted by N.
Assume that the floors have equal populations. State all the assumptions that you
make in your derivation.
Solution
We shall assume equal floor populations and that passenger destinations areindependent (i.e., one passengers choice of destination will not influence anotherpassengers choice of destination).
Derivation of the probable number of stopsThe probably that passengerjwill stop at a floor i:
N
1)iflooratstopwilljpass(P
7/25/2019 000 Round Trip Time Calculations
9/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 9 of 24
where N is the number of floors above the main lobby. Thus the probability thatpassengerjwill not stop at a floor iis:
N
11)iflooratstopNOTwilljpass(P
But the car contains Ppassengers. So the probability that none of them will stop atfloor iis the product of all of their respective probabilities:
P
N
11)iflooratstopNOTwillpassall(P
where Pis the number of passengers in the car when it leave the ground floor. Thecomplement of this quantity is the probability that at least one passenger will stop at
a floor:
P
N
111)iflooraatstopwillpassoneleastat(P
But this is the same as the probability that a stop will take place on floor i. So theprobability of stopping on a floor iis:
P
N
111)iflooratstopa(P
The expected value of the number of stops can be obtained by adding theprobabilities of stopping on all N.
PN
1i
P
N
111N
N
1111stopsofnumberE
Thus the probable number of stops S is equal to:
P
N111NstopsofnumberES
13. Mathematical Proof the Highest Reversal Floor for Equal Floor PopulationsStarting from first principles, derive an expression for the probable highest reversalfloor (H) that a lift will make in a round trip journey during up peak (incoming traffic).
Under up peak (incoming traffic) conditions, the lift will fill up with passengers atthe ground floor, and then deliver the passengers to their destinations in the upperfloors. It then expresses back to the ground floor to collect more passengers and soon.
The car has a capacity CC, but only fills up to P passengers. The number offloors above ground is denoted by N.
7/25/2019 000 Round Trip Time Calculations
10/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 10 of 24
Assume that the floors have equal populations. State all the assumptions that youmake in your derivation.
Solution
The probably that passengerjwill stop at a floor i:
N
1)iflooratstopwilljpass(P
where N is the number of floors above the main lobby. Thus the probability thatpassengerjwill not stop at a floor iis:
N
11)iflooratstopNOTwilljpass(P
But the car contains P passengers. So the probability that none of them will stop atfloor iis the product of all of their respective probabilities:
P
N
11)iflooratstopNOTwillpassall(P
The probability that the lift will not travel any higher than a floor iis the probability thatit will not stop on floor i+1or i+2or i+3all the way to floor N. This is expressed asthe product of these individual probabilities:
PPPPP
1i
11
2i
11.......
2N
11
1N
11
N
11
)ifloorabovetravelnotwilllift(P
This can be re-written as:
PPPPP
1i
i
2i
1i
.......2N
3N
1N
2N
N
1N
)ifloorabovetravelnotwilllift(P
Putting all terms inside the same bracket gives:
P
1i
i
2i
1i.......
2N
3N
1N
2N
N
1N
)ifloorabovetravelnotwilllift(P
This simplifies to:
7/25/2019 000 Round Trip Time Calculations
11/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 11 of 24
P
N
i)ifloorabovetravelnotwilllift(P
Note that this is also equal to the probability that the highest reversal floor will be any
of the floors 1 to i. In other words, it is the probability that the higher reversal floorwill be floor 1 or 2 or 3..or i, or the sum of these probabilities.
)().........3()2()1()( iHPHPHPHPifloorabovetravelnotwillliftP
Applying the same argument to floor i-1, gives the following:
P
N
iifloorabovetravelnotwillliftP
1
)1(
Note that this is also equal to the probability that the highest reversal floor will be anyof the floors 1 to i-1. In other words, it is the probability that the higher reversal floorwill be floor 1 or 2 or 3..or i-1, or the sum of these probabilities.
)1().........3()2()1()( iHPHPHPHPifloorabovetravelnotwillliftP
If we subtract the two expressions from each other only one term remains (which isthe probability that the highest reversal floor is i. So the probability that the i
thfloor is
the highest reversal floor is the probability that the lift does not travel above the ithfloor minus the probability that the lift does not travel above the (i-1)
thfloor. Thus:
PP
N
i
N
ifloorreversalhighesttheisifloorP
1)(
But any of the floors from 1 to Ncould be the highest reversal floor. The expectedvalue of the highest reversal is the weighted sum of all the possible highest reversalfloors (i.e., 1to N) each multiplied by their respective probabilities:
N
1i
PP
N
1i
N
i
i)H(E
)floorreversalhighest(valueectedexp
Re-arranging the two terms will make it easier to simplify later on:
N
1i
PP
N
i
N
1ii)H(E
Expanding gives:
7/25/2019 000 Round Trip Time Calculations
12/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 12 of 24
PPPP
PPPPPP
PPPP
PPPPPP
N
NN
N
1NN
N
1N1N
N
2N1N
...N
33
N
23
N
22
N
12
N
1
N
0
N
N
N
1NN
N
1N
N
2N1N
...N
3
N
133
N
2
N
122
N
1
N
111)H(E
Simplifying gives:
NN
1N
.....N
3
N
2
N
1
0)H(E
PPPP
This can be rearranged as:
1N
1i
P
N
iN)H(E
Note that the summation extends only to N-1 (i.e., not N). Also note that themaximum possible value of His N, which is to be expected at high values of P.
14. Mathematical Proof the Lowest Floor Express for Equal Floor PopulationsStarting from first principles, derive an expression for the probable lowest floor towhich the lift will travel without stopping in a round trip journey during up peak(incoming traffic).
Under up peak (incoming traffic) conditions, the lift will fill up with passengersat the ground floor, and then deliver the passengers to their destinations in the upperfloors. It then expresses back to the ground floor to collect more passengers and soon.
The car has a capacity CC, but only fills up to P passengers. The number offloors above ground is denoted by N. Assume that the floors have equal populations.
State all the assumptions that you make in your derivation.
Solution
The probably that passengerjwill stop at a floor i:
N
1)iflooratstopwilljpass(P
where N is the number of floors above the main lobby. Thus the probability thatpassengerjwill not stop at a floor iis:
7/25/2019 000 Round Trip Time Calculations
13/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 13 of 24
N
11)iflooratstopNOTwilljpass(P
But the car contains P passengers. So the probability that none of them will stop at
floor iis the product of all of their respective probabilities:
P
N
11)iflooratstopNOTwillpassall(P
The probability that the lift will not stop at any floor lower than iis the probability thatit will not stop on floor 1, 2, 3 all the way to floor i-1. This is expressed as theproduct of these individual probabilities:
PPPP
iNNNN
ibelowflooranyatstopnotwillelevatorP
2
11.......
2
11
1
11
11
)(
This can be re-written as:
PPPPP
iN
iN
iN
iN
N
N
N
N
N
N
ibelowflooranyatstopnotwillelevatorP
2
1
1.......
2
3
1
21
)(
Putting all terms inside the same bracket gives:
P
iN
iN
iN
iN
N
N
N
N
N
N
ibelowflooranyatstopnotwillelevatorP
2
1
3
2.......
2
3
1
21
)(
This simplifies to:
P
N
iNibelowflooranyatstopnotwillelevatorP
1)(
The term above is the probability that the elevator will not stop at any floor lower thanthe ithfloor. In effect it is also that probability that any of the floors above the ithfloorcould be the lowest call express.
In a similar manner, the probability that the lift will not stop at a floor below thei+1th floor can be calculated as shown below:
P
N
iNibelowflooranyatstopnotwillelevatorP
)1(
7/25/2019 000 Round Trip Time Calculations
14/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 14 of 24
The term above is the probability that the elevator will not stop at any floor lower thanthe i+1thfloor. In effect it is also that probability that any of the floors above the i+1thfloor could be the lowest call express.
Subtracting the two expressions from each other, gives the probability that theithfloor is the lowest floor express (i.e., is on average the floor at which the elevatormakes the first stop when travelling in the up direction on a round trip journey). Theprobability that the ith floor is the lowest floor express is the probability that the liftdoes not stop below the i
thfloor minus the probability that the lift does not stop below
the (i+1)thfloor. Thus:
PP
N
iN
N
iNP
1)expresscalllowesttheisifloor(
But any of the floors from 1 to N could be the lowest call express. The expectedvalue of the lowest call express is the weighted sum of all the possible lowest call
express floors (i.e., 1to N) each multiplied by their respective probabilities:
N
i
PP
N
iN
N
iNiLCEE
valueected
1
1)(
)expresscalllowest(exp
Re-arranging the two terms will make it easier to simplify later on:
N
i
PP
N
iN
N
iN
iLCEE1
1
)(
Expanding gives:
1
1
1
01.......
3211
01121
...32
321
21
1)(
N
i
P
PPPPP
PPPP
PPPPPP
N
iLCE
NNN
N
N
N
N
N
NNN
NNN
N
N
N
N
N
N
N
N
N
N
N
NLCEE
Simplifying gives:
PPPPP
NNN
N
N
N
N
NLCE
01.......
3211
7/25/2019 000 Round Trip Time Calculations
15/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 15 of 24
This can be rearranged as:
1
1
1N
i
P
N
iLCEE
Note that the summation extends only to N-1 (i.e., not N). Also note that theminimum possible value of LCEis 1, which is to be expected at high values of P.
Comparing the equation for Hand the equation for LCEwe can see that thesame summation term exists in both. The difference between Nand H is the samedifference between LCEand 1 (symmetrical values between 1 and N). The additionof Hand LCEalways results in the value of N+1.
1 NLCEH
15. Assumptions in deriving the basis round trip time equationWhen deriving the basic equation for the round trip time, the following assumptionshave been made:
1. Equal floor populations in the derivation of H and S.2. Passenger choices of floors are independent of each other (this affects the
derivation of H and S).3. Constant passenger arrival rate. It is assumed that the arrival process of
passengers is not random and that passengers arrive in a uniform mannerwith equal time spacing between them. In reality passengers arrive randomlyin a process that is best represented by a Poisson arrival process.
4. An important assumption made in the derivation f the round trip time equationis that the top speed is attained in one floor journey. This is not correct inmany cases where the speed is above 2.5 ms
-1.
5. It has been assumed that only one passenger is boarding or alighting at thesame time.
6. The only type of traffic present is the incoming traffic (up peak traffic).7. Equal floor heights have been assumed.8. It has been assumed that the doors starts closing immediately after the last
passenger has boarded or alighted. In reality there will be delay depending onthe timer controlling the door operation, and depending on whether otherpassengers use the door close button.
9. It has been assumed that passengers enter the building from one singleentrance. In reality many buildings have underground car parks or differentlevel street entrances.
10. No door re-openings have been assumed.11. It has been assumed that all lifts in the same group serve all floors and that
any passenger regardless of his/her destination can board any available lift.
16. Solved Design ExerciseThe parameters for an office building are shown below.
Assume the following parameters:
a. Passenger arrival rate is 15%.b. Number of floors above ground is 14 floors.
7/25/2019 000 Round Trip Time Calculations
16/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 16 of 24
c. Car capacity is 21 person (1600 kg).d. Floor height is 4.5 m (finished floor level to finished floor level).e. Three basement floors, B1, B2, B3 used as car parks.f. Basement floor height is 4.5 m.g. Top speed, v, is 1.6 ms
-1.
h. Top acceleration, a, is 1 ms-2.i. Top jerk,j, is 1 ms-3.j. Passenger transfer time out of the car is 1.2 s.k. Passenger transfer time into the car is 1.2 s.l. Door opening time is 2 s.m. Door closing time is 3 s.n. Advanced door opening is 0.5 s.o. Start delay is 1 s.p. Total building population of 1100 persons.q. Equal floor populations.
Find the number of lifts required assuming no arrivals from the basement.Find the actual interval and the actual handling capacity.
SolutionThe equation for the round trip time ( ) can be written as follows:
v
ddttPtttt
v
dtS
v
dH
fG
popiaosddcdo
f
f
f212
Where: is the round trip time in s
His the highest reversal floor (where floors are numbered 0, 1, 2.NS is the probably number of stopsdfis the typical height of one floor in mvis the top rated speed in m/stfis the time taken to complete a one floor journey in s assuming that the lift attains
the top speed vPis the number of passengers in the car when it leaves the ground floor (does not
have to be an integer for this calculation, but is used as an integer for thepurposes of calculating Hand S)
dGis the height of the ground in m where more than the typical floor heighttdois the door opening time in stdcis the door closing time in stsdis the motor start delay in staois the door advance opening time in s (where the door starts opening before the
car comes to a complete standstill)tpiis the passenger boarding time in stpois the passenger alighting time in s
We need to check that the lift will attain top speed in a one floor journey.We use the following equation as a check:
7/25/2019 000 Round Trip Time Calculations
17/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 17 of 24
16.41
16.16.11
aj
jvva5.4d
222
So the top speed of 1.6 m/s will be attained in a one floor jump. In this case, the time
taken to complete a one floor journey, tfwill be:
s4.51
1
1
6.1
6.1
5.4
j
a
a
v
v
dtf
We first start by finding the value of P based on 80% car loading. P works out as16.8 passengers.
Moving on to calculate H and S as follows:
1014
1
1114N
1
11NS
8.16P
62.13......0174.0075.0288.01414
i14
N
iNH
13
1i
8.161N
1i
P
Substituting in the RTT equation gives:
s
v
ddttPtttt
v
dtS
v
dH
fG
popiaosddcdo
f
f
f
82.2053.40895.76
6.1
5.45.422.12.18.165.0132
6.1
5.44.5110
6.1
5.46.132
212
In order to meet the expected arrival rate of 15%, the number of lifts required can becalculated as follows:
738.68.16300
82.205110015.0
300
%
300%
P
UHCL
U
PLHC
So the nearest larger integer is 7 lifts. So seven lifts are required to achieve thehandling capacity that meets the expected arrival rate.
In practice the handling capacity achieved will be:
%6.15110082.205
8.167300300%
U
PLHC
which is more than the expected arrival rate of 15%.
7/25/2019 000 Round Trip Time Calculations
18/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 18 of 24
The achieved interval will be:
sL
int 4.297
82.205
which is less than the 30 s limit specified for offices.
ProblemsFor each of the following cases, design a suitable VT system, by finding the suitablenumber of elevators and their speed, as well as the actual car loading.
Try to find the most economical solution by looking for the minimum number ofelevators that meets the requirements.Assume equal floor population and equal floor heights.In using the round trip time equation ignore the fact that the top speed has not been
attained.Select the speed v by dividing the total travel distance and then rounding downto thenearest preferred speed (1, 1.6, 2, 2.5, 3.15, 4, 5, 6.3, 8, 10 ms
-1).
Find:L, v, Pact, intactand HC%Also calculate the actual car loading. Actual car loading = (Pact/CC)%
Assume that the door opening time is 2 sAssume that the door closing time is 3 sAssume that the start delay is 1 s
Assume that the advance door opening is 0.5 s.Assume that the passenger transfer time is 1.2 sAssume that the acceleration,a,= 1 ms-2Assume that the jerk,j, = 1.5 ms
-3
1. Office Building: An office building has the following parameters.N= 20 floors above the main terminal.AR%= 12%Target interval, inttarof 30 sCar capacity, CC, of 26 personsFloor height, df,= 4.5 m
Total population, Uis 1600 persons
Assume one single main entrance.
2. Office Building: An office building has the following parameters.N= 25 floors above the main terminal.AR%= 10%Target interval, inttarof 25 sCar capacity, CC, of 26 personsFloor height, df,= 4.5 m
Total population, Uis 1000 persons
Solve for the following two cases:
7/25/2019 000 Round Trip Time Calculations
19/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 19 of 24
a) Single entrance without any basements.b) One main entrance and three car park basements, each basement with an arrivalpercentage of 6% for each.
3. Office Building: An office building has the following parameters.N= 12 floors above the main terminal.AR%= 15%Target interval, inttarof 30 sCar capacity, CC, of 26 personsFloor height, df,= 4.5 mTotal population, Uis 800 persons
Assume one single main entrance.
4. Residential Building: An office building has the following parameters.
N= 30 floors above the main terminal.AR%= 7%Target interval, inttarof 50 sCar capacity, CC, of 16 personsFloor height, df,= 3.2 mTotal population, Uis 240 persons
Assume one single main entrance.
References1. Basset Jones The probable number of stops made by an elevator GE Review
26(8) 583-587 (1923)
7/25/2019 000 Round Trip Time Calculations
20/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 20 of 24
Appendix AThe Round Trip Time Equation for the Case of Unequal Floor Heights
In the case where the floor heights are unequal, this will have an effect on thecalculation of the round trip time equation. The equation for the round trip time canbe amended as follows in order to account for this case as follows.
The effect of the unequal floor heights can be taken into consideration byassuming an effective floor height df effthat can be inserted into the original round triptime equation.
The effective floor height df eff is the expected value fo the floor height. Theeffective floor height is the weighted average of all the floor heights multiplied by theprobability of the elevator passing through that floor. In order for the elevator to passthrough a floor it should travel to any of the floors above that floor. Thus it isnecessary to find the probability of the elevator travelling above a certain floor, i.
The probability of the elevator not stopping at a certain floor, assuming equal
floor populations is the probability that passengerjwill stop at a floor i:
N
1)iflooratstopwilljpass(P (1)
where N is the number of floors above the main lobby. Thus the probability thatpassengerjwill not stop at a floor iis:
N
11)iflooratstopNOTwilljpass(P (2)
But the car contains P passengers. So the probability that none of them will stop atfloor iis the product of all of their respective probabilities:
P
N
11)iflooratstopNOTwillpassall(P
(3)
The probability that the lift will not travel any higher than a floor iis the probability thatit will not stop on floor i+1or i+2or i+3all the way to floor N. This is expressed asthe product of these individual probabilities:
PPPPP
1i
11
2i
11.......
2N
11
1N
11
N
11
)ifloorabovetravelnotwilllift(P
(4)
This can be re-written as:
PPPPP
1i
i
2i
1i.......
2N
3N
1N
2N
N
1N
)ifloorabovetravelnotwilllift(P
(5)
7/25/2019 000 Round Trip Time Calculations
21/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 21 of 24
Putting all terms inside the same bracket gives:
P
1i
i
2i
1i.......
2N
3N
1N
2N
N
1N
)ifloorabovetravelnotwilllift(P
(6)
This simplifies to:
P
N
i)ifloorabovetravelnotwilllift(P
(7)
Thus the probability that the lift will travel above the floor iis:
P
NiifloorabovetravelwillliftP
1)( (8)
Thus the expected value of the travel distance can be calculated as the weightedaverage of the various floor height as follows:
P
f
P
f
P
f
P
ftotal
N
NNd
N
NNd
Nd
NddE
11
11
...2
121
11
(9)
Where:E(dtotal)is the expected value of the distance travelled in the up direction.
The last term above reduces to zero (as it is impossible for the elevator to passthrough floor N). The expected floor height is obtained by dividing the expected totatravel distance by the highest reversal floor, H. So the equation for the effective floorheight can be expressed as shown below (assuming equal floor populations):
H
Niid
dE
N
i
P
f
f
1
1
1(10)
Where:
idf is the floor height for floor i
fdE is the expected value of the floor heights (effective floor height)
H is the highest reversal floor
Nis the number of floors above the main terminalPis the number of passengers boarding the car from the main terminal
7/25/2019 000 Round Trip Time Calculations
22/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 22 of 24
Appendix BProof of the time for a one floor journey assuming that the top speed has been
attained
Assume the journey is split into 6 parts: d1, d2, d3, d4, d5, d6and d7. Also assume thetime duration for each part is t1, t2, t3, t4, t5, t6and t7 respectively. The total distanceof the journey is d,the top speed is v, the top acceleration is aand the jerk is constantat a value ofj.
Note from symmetry the following equations apply:
7531 tttt
And:
62 tt
The distances are also equal as follows:
71 dd
53 dd
62 dd
At the end of the time t1, the acceleration would have attained its top value. Hence:
j
at 1
The speed at the time t1is:
7/25/2019 000 Round Trip Time Calculations
23/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
Copyright held by the author 2011, Lutfi Al-Sharif Page 23 of 24
j
atjtv
22
1 2211
The speed at the time t1+t2is:
j
avttv
2
2
21
The distance covered at time t1is:
2
3
0
2
162
11
j
adttjd
t
The distance d3is equal to the area of a rectangle less the area d1(from symmetry).
2
3
2
3
1366 j
a
j
av
j
atvd
The time t2can be calculated as follows:
j
a
a
v
a
j
a
j
av
t
22
22
2
The area d2is the area of a trapezoid, calculated as follows:
j
av
a
v
j
a
a
vvt
j
a
j
av
d2222
22 2
2
22
2
The total distance d1+d2+d3+d5+d6+d7can be calculated as follows:
a
v
j
av
j
av
a
v
j
avdddddd
22
76532122
2
a
v
j
avddddddddd
2
7653214
7/25/2019 000 Round Trip Time Calculations
24/24
3 Elevator Traffic Analysis andDesign
Selected Topics in Mechatronics 0908589
C i ht h ld b th th 2011 L tfi Al Sh if P 24 f 24
j
a
a
v
v
d
v
a
v
j
avd
t
2
4
j
a
a
v
v
d
j
a
a
v
v
d
j
a
a
v
j
atttt 2424 421
Top Related