ZXIN10 SACP CDR Server Installation Guide
-
Upload
ahmed-badr -
Category
Documents
-
view
70 -
download
10
description
Transcript of ZXIN10 SACP CDR Server Installation Guide
Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE
ZXIN10 SACP
CDR Server Installation Guide
ZTE CORPORATION
Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE
Revision History
Document
No.
Version
No.
Drafted
/Modified by Reviewed by
Drafted/M
odified on
Reason for
Revision
Major
Revisions
R1.0 Zhou Jiyou Zhu Liangui 2010-02-4 CDR installation
guide Revision
Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE i
Table of Contents
Chapter 1 Overview ........................................................................................................................ 1 1.1 Introduction ................................................................................................................................. 1 1.2 Technical Terms .......................................................................................................................... 1 1.3 CDR Server ................................................................................................................................ 1 1.4 Installation & Configuration Flow ................................................................................................ 3 1.4.1 Flow Chart ............................................................................................................................... 3 1.4.2 Flow description ...................................................................................................................... 3
Chapter 2 Install CDR Server Platform ......................................................................................... 5 2.1 General ....................................................................................................................................... 5 2.2 Uploading Version ...................................................................................................................... 5 2.3 Install CDR Server Platform ....................................................................................................... 5 2.3.1 Install IMP1.3 Platform ............................................................................................................ 5 2.3.2 Install IMP2.1 Platform ............................................................................................................ 7
Chapter 3 Configure CDR Server Platform ................................................................................ 14 3.1 General ..................................................................................................................................... 14 3.2 Configuration Flow Description ................................................................................................ 14 3.2.1 Configure IMP1.3 Platform .................................................................................................... 14 3.2.2 Configure IMP2.1 Platform .................................................................................................... 18
Chapter 4 Configure SERVER-U ................................................................................................. 23 4.1 General ..................................................................................................................................... 23 4.2 Configuration Flow Description ................................................................................................ 23 4.2.1 Flow Chart ............................................................................................................................. 23 4.2.2 Flow Description .................................................................................................................... 23
Chapter 5 Configure ZTE-HA Cluster ......................................................................................... 27 5.1 General ..................................................................................................................................... 27 5.2 Configuration Flow Description ................................................................................................ 27 5.2.1 Flow Chart ............................................................................................................................. 27 5.2.2 Flow Description .................................................................................................................... 27
Chapter 6 Verify CDR Server ....................................................................................................... 34 6.1 General ..................................................................................................................................... 34 6.2 Verifying CDR server ................................................................................................................ 34
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 1
Chapter 1 Overview
1.1 Introduction
This chapter describes the entire installation flow for CDR server, the function of
CDR server, and the interconnection between CDR server and other network
element.
Section 2 introduces the technical terms in this text.
Section 3 introduces the effect of the CDR server.
Section 4 introduces the installation flow of the CDR server.
This article describes the process for building CDR server under Windows
platform, which can be a guide for the fast installation of CDR server on site.
Chapter 2 introduces the installation process of the CDR server platform.
Chapter 3 introduces the configuration method of the CDR server platform.
Chapter 4 introduces the configuration of SERVER-U.
Chapter 5 introduces the configuration of ZTE-HA cluster server.
Chapter 6 introduces the verification of CDR server.
1.2 Technical Terms
Abbreviation Full Name
CDR Call Detail Record
IMP Interface Message Processor
Ftp File Transfer Protocol
Windows Microsoft Windows
ZXIN ZTE Intelligent Network
DLL Dynamic Link Library
Server Server
SACP Service Access Control Part
1.3 CDR Server
Introduction
CDR server is responsible for the CDR collection for SACP platform and the
format conversion of CDR as required. It also provides FTP service interface for
the third-party to obtain the desired CDR.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 2
The interconnection between CDR server and other network element is shown
in Figure 1.3-1.
Figure 1.3-1 Interconnection between CDR and Other Network Elements
The two network elements interconnected with CDR server are SCP and
BOSS.CDR is connected to SCP via FTP to obtain CDR and store it under the
CDR local directory. Then, BOSS is connected to the CDR storage directory via
FTP to obtain CDR.
The versions of CDR server are only available for Windows platform. At present,
there are only two versions: V1.* and V2.1.
Function Description
The CDR server in SACP service has two functions: CDR collection and FTP
interface for obtaining CDR.
1. CDR collection function: collect the original CDR from service control
point or database.
2. Provide FTP interface to obtain CDR.
Enable FTP function.
Set up FTP user.
Wait for BOSS to obtain CDR.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 3
1.4 Installation & Configuration Flow
1.4.1 Flow Chart
Install CDR Server
Start
Configure CDR
Server
Configure SERVER-U
Configure ZTE-HA Cluster
Check CDR Server
End
Figure 1.4-1 Configuration Flow Chart for CDR Server Installation
1.4.2 Flow description
Purpose
To deploy the CDR server correctly so that all the functions can be used
Personnel
ZXIN10 SACP engineering implementation personnel
Prerequisites
1. The installation of Windows Server operating system for the target
equipment is completed.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 4
2. The patch update and installation of security protection software for
operating system are completed.
3. The built-in internet information service of operating system is closed.
4. The disk array has been mounted successfully.
5. The installation of ZTE-HA and server-u is completed.
Tools
Two PC SERVERs
Procedure Description
1. Install CDR server platform.
2. Configure CDR server platform.
3. Configure server-u.
4. Configure ZTE-HA cluster.
5. Verify CDR server.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 5
Chapter 2 Install CDR Server Platform
2.1 General
This chapter describes the installation procedures of CDR server platform.
Section 2 introduces the method to upload the version of CDR server.
Section 3 introduces the method to create CDR server platform.
2.2 Uploading Version
Purpose
To upload the CDR server version to the CDR server
Personnel
ZXIN10 SACP engineering implementation personnel
Procedure Description
1. Select the correct CDR server platform version, such as IMPV*.*.
2. Copy the CDR server platform version to the CDR server via U-disk. For
remote operation, send the version to CDR server via the remote control
tools such as Radmin and Dameware.
2.3 Install CDR Server Platform
2.3.1 Install IMP1.3 Platform
Purpose
To complete the installation of CDR server platform
Personnel
ZXIN10 SACP engineering implementation personnel
Procedure Description
1. Decompress the CDR server platform version.
2. Copy the Imp directory in the decompressed version package into the
directory C:\zxin10, as shown in Figure 2.3-1.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 6
Figure 2.3-1 Correct Storage Position for IMP Directory
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 7
2.3.2 Install IMP2.1 Platform
2.3.2.1 Flow Chart
Set Running Environment
Start
Decompress CDR Version
Copy version to IMP Directory
End
Figure 2.3-2 Installation Flow Chart for CDR Server Platform
2.3.2.2 Flow Description
Purpose
To complete the installation of CDR server platform
Personnel
ZXIN10 SACP engineering implementation personnel
Procedure Description
1. Set running environment.
(1) Right click My Computer on the desktop, and click Properties in the
pop-up menu to open the System Properties dialog box, as shown in
Figure 2.3-3 and Figure 2.3-4.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 8
Figure 2.3-3 Setting Environment Variables
Figure 2.3-4 Setting Environment Variables
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 9
(2) Click Environment Variables button in Figure 2.3-4 to open the dialog
box. Add the environment variable of ZXINHOME, and add C:\zxin10\bin
and C:\zxin10\lib into the Path environment variables, as shown in
Figure 2.3-5 to Figure 2.3-9.
Figure 2.3-5 Setting Environment Variables
Click New to set ZXINHOME environment variables.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 10
Figure 2.3-6 Setting Environment Variables
Click OK to add ZXINHOME into the system variables.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 11
Figure 2.3-7 Setting Environment Variables
Find the Path variable in the system variables.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 12
Figure 2.3-8 Set environment variables
Click Edit or double-click Path to open the Edit System Variable dialog
box to edit path. Add C:\zxin10\bin and C:\zxin10\lib into the field for
Variable Value, as shown in Figure 2.3-9.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 13
Figure 2.3-9 Setting Environment Variables
2. Decompress the CDR server platform version.
3. Copy the Imp directory in the decompressed version package into the
directory C:\zxin10, as shown in Figure 2.3-10.
Figure 2.3-10 Correct Storage Position for IMP Directory
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 14
Chapter 3 Configure CDR Server Platform
3.1 General
After the installation of CDR server platform is completed, it is required to
configure the platform configuration file imp.ini to ensure the normal running of
platform. For IMP2.1 platform, the user also needs to configure the module.ini
file.
Section 2 explains the configuration method for the configuration file of CDR
server platform, and describes the configuration used in engineering in details.
3.2 Configuration Flow Description
3.2.1 Configure IMP1.3 Platform
Purpose
To make the CDR server platform work properly
Personnel
ZXIN10 SACP engineering implementation personnel
Procedure Description
1. Configure Imp.ini file.
(1) Configuration description of [general] section
alarm = 0
comm = 0 ……CDR server does not need to establish
link with any other network element.
activeNewComm = 0
dbconn = 0 ……CDR server does not need to create
any database connection.
logfilenum = 30 ……This value is enough for the CDR
server.
interfacecount = 0 ……Determine this value according to the
number of interfaces opened by the CDR server.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 15
ftpcnt = 1 ……Determine this value according to the
number of FTP threads opened by the CDR server.
cdrconvertcnt = 0 ……Determine this value according to the
number of Dll for platform CDR conversion opened by the CDR server.
The SACP service does not need CDR conversion, so the value is 0.
monitor = 0
logfilepath = c:\zxin10\log ……Keep the default value
CpuOccupy = 80 ……Keep the default value or
configure it to 0.
(2) Configuration description of [idf*] section
If dbconn = 0 in [general] section, the functions for this section are
disabled. Generally, the configuration of [idf*] section is not required for
CDR server.
(3) Configuration description of [interface*] section
If interfacecount = 0 in [general] section, the functions for this section are
disabled.
(4) Configuration description of [imptrace] section
logwrite = 0
tracepno = ……interface tread number traced by the
IMP log The CDR server of SACP service does not need to use interface,
so it is null here.
encyptfname = all
(5) Configuration description of [assist] section
Since CDR server has no interface service function and does not require
message communication with any network element, all the functions for
this section are disabled.
(6) Configuration description of [alarm] section and [vmalarm] section.
For CDR server, the alarm module function is usually disabled, which
means alarm = 0 in [general] section. And the functions for [alarm]
section and [vmalarm] section are disabled.
(7) Configuration description of [monitor] section
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 16
For CDR server, the Monitor automatic changeover function is usually
disabled, which means monitor = 0 in [general] section. And the functions
for [monitor] section are disabled.
(8) Configuration description of [ftpap*] section
This section configures the internal FTP thread of CDR server platform. It
is used to obtain the original CDR from service control point or database.
These FTP threads can download and upload CDR.
ftpgetaddress = 192.168.1.133 ;destination address to obtain
and send CDR
ftpgetusername = zxin10
ftpgetpassword = zxin10
ftpgetport = 21
ftpgetdir =/home/zxin10/cdr ;directory to obtain CDR
ftpgetscp = 0
As shown in the above configuration, FTP thread is responsible for
obtaining the original CDR from 192.168.1.133. The user name and
password for the automatic login of FTP are zxin10. The login port is 21.
The login path is the CDR subdirectory under the current directory. The
obtained CDR should be saved in the preset directory of CDR server.
The configuration options are given below.
ftpputdircount = 1 ……directory number of the local CDR
ftpputdir = e:\sacp, ……specific directory of the local
CDR
putdirproperty =0 ……method to store the CDR of each
directory
putdirbakdays = 90 ……Retention days for CDR of each
directory
opertype = 0 ……the method for FTP to obtain CDR.
It must be configured to be 0, which is the binary method.
filename = in01_G_101_*.r ……the type of CDR obtained
from the target equipment. in01_G_101_*.r indicates the CDR type such
as in01_G_101_09123000798.r; * indicates any contents.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 17
dealflag = 3 ……the way to deal with the obtained
CDR from the target equipment. Avoid obtaining the same CDR.
tempdir = o
begintime = 00000000 ……set the beginning time to obtain
CDRTime format: XX day XX hour XX minute XX second
endtime = 31240000 ……set the ending time for obtaining
CDRTime format: XX day XX hour XX minute XX second
interval = 60 ……the time interval for FTP to obtain
CDR. It is usually configured to be 60, which means to obtain CDR every
minute.
The above text introduces the configuration for FTP to download CDR.
The text below begins to describe the relevant configuration for CDR
upload, the configuration method of which is similar to the one for CDR
download.
ftpputaddress =
ftpputusername = wxp
ftpputpassword = 4321
ftpputport = 21
(9) Configuration description of [cdrconvert*] section
Configure the relevant information of CDR conversion Dll. If there is N
[cdrconvert*], cdrconvertcnt = N in [general] section.
cdrconvertcnt = 0 in [general] section. At present, [cdrconvert*] is closed.
(10) Configuration description of [sftp] section
Just keep the default value without modification.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 18
3.2.2 Configure IMP2.1 Platform
3.2.2.1 Flow Chart
Start
Config Module.ini
Config imp.ini
End
Figure 3.2-1 Configuration Flow Chart for CDR Server Platform
3.2.2.2 Flow Description
Purpose
To make the CDR server platform work normally
Personnel
ZXIN10 SACP engineering implementation personnel
Procedure Description
1. Configure module.ini
[general]
ipcmode=0 ----- Only refer to the module number to locate the
receiving party in communication. Since ipcmode is configured to be 0
for intelligent network platform, imp is consistent with the IN platform.
ctimode=0
isenglish=0
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 19
isimpmode=1 ----- zxinos is running under imp mode, so it
must be configured to 1.
modulecount=3 ----- the number of processes to be enabled.
It is configured to 3 here, which means to enable three processes:
impcomm, impassist, impservice
iszxinitexit=0
zxshmem=1
zxshsize=100
zxshhead=0x40000000 ----- first address of the shared memory. It
should be configured to 0x30000000 under XP.
chkshmrate=90
[module1]
startscript=impcomm.exe -----communication process
[module2]
startscript=impservice.exe -----It is responsible for the loading and
application of IMP dynamic library.
[module3]
startscript=impassist.exe -----mainly provide functions such as ftp,
cdconvert and vmalarm
2. Configure Imp.ini file.
(1) Configuration description of [general] section
alarm = 0
comm = 0 ……CDR server does not need to establish
link with any other network element.
activeNewComm = 0
dbconn = 0 ……CDR server does not need to create
any database connection.
logfilenum = 30 ……This value is enough for the CDR
server.
interfacecount = 0
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 20
……Determine this value according to the number of interfaces opened
by the CDR server.ftpcnt = 1 ……Determine this
value according to the quantity of FTP threads opened by the CDR
server.
cdrconvertcnt = 0 ……Determine this value according to the
quantity of Dll for platform CDR conversion opened by the CDR server.
The SACP service does not need CDR conversion, so the value is 0.
monitor = 0
logfilepath = c:\zxin10\log ……Keep the default value
CpuOccupy = 80 ……Keep the default value or
configure it to 0.
(2) Configuration description of [idf*] section
If dbconn = 0 in [general] section, the functions for this section are
disabled. Generally, the configuration of [idf*] section is not required for
CDR server.
(3) Configuration description of [interface*] section
If interfacecount = 0 in [general] section, the functions for this section are
disabled.
(4) Configuration description of [imptrace] section
logwrite = 0
tracepno = ……interface tread number traced by the
IMP log The CDR server of SACP service does not need to use interface,
so it is null here.
encyptfname = all
(5) Configuration description of [assist] section
Since CDR server has no interface service function and does not require
message communication with any network element, all the functions for
this section are disabled.
(6) Configuration description of [alarm] section and [vmalarm] section.
For CDR server, the alarm module function is usually disabled, which
means alarm = 0 in [general] section. And the functions for [alarm]
section and [vmalarm] section are disabled.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 21
(7) Configuration description of [monitor] section
For CDR server, the Monitor automatic changeover function is usually
disabled, which means monitor = 0 in [general] section. And the functions
for [monitor] section are disabled.
(8) Configuration description of [ftpap*] section
This section configures the internal FTP thread of CDR server platform. It
is used to obtain the original CDR from service control point or database.
These FTP threads can download and upload CDR.
ftpgetaddress = 192.168.1.133 ;destination address to obtain
and send CDR
ftpgetusername = zxin10
ftpgetpassword = zxin10
ftpgetport = 21
ftpgetdir =/home/zxin10/cdr ;directory to obtain CDR
ftpgetscp = 0
As shown in the above configuration, FTP thread is responsible for
obtaining the original CDR from 192.168.1.133. The user name and
password for the automatic login of FTP are zxin10. The login port is 21.
The login path is the CDR subdirectory under the current directory. The
obtained CDR should be saved in the preset directory of CDR server.
The configuration options are given below.
ftpputdircount = 1 ……directory quantity of the local CDR
ftpputdir = e:\sacp, ……specific directory of the local
CDR
putdirproperty =0 ……method to store the CDR of each
directory
putdirbakdays = 90 ……Retention days for CDR of each
directory
opertype = 0 ……the method for FTP to obtain CDR.
It must be configured to be 0, which is the binary method.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 22
filename = in01_G_101_*.r ……the type of CDR obtained
from the target equipment. in01_G_101_*.r indicates the CDR type such
as in01_G_101_09123000798.r; * indicates any contents.
dealflag = 3 ……the way to deal with the obtained
CDR from the target equipment. Avoid obtaining the same CDR.
tempdir = o
begintime = 00000000 ……set the beginning time to obtain
CDRTime format: XX day XX hour XX minute XX second
endtime = 31240000 ……set the ending time for obtaining
CDRTime format: XX day XX hour XX minute XX second
interval = 60 ……the time interval for FTP to obtain
CDR. It is usually configured to be 60, which means to obtain CDR every
minute.
The above text introduces the configuration for FTP to download CDR.
The text below begins to describe the relevant configuration for CDR
upload, the configuration method of which is similar to the one for CDR
download.
ftpputaddress =
ftpputusername = wxp
ftpputpassword = 4321
ftpputport = 21
(9) Configuration description of [cdrconvert*] section
Configure the relevant information of CDR conversion Dll. If there is N
[cdrconvert*], cdrconvertcnt = N in [general] section.
cdrconvertcnt = 0 in [general] section. At present, [cdrconvert*] is closed.
(10) Configuration description of [sftp] section
Just keep the default value without modification.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 23
Chapter 4 Configure SERVER-U
4.1 General
This chapter introduces the configuration of server-u.
Section 2 explains the method to create FTP users on server-u and set up user
directory rights.
4.2 Configuration Flow Description
4.2.1 Flow Chart
Start
Create User
Set user directory right
End
Figure 4.2-1 Configuration Flow Chart for CDR Server Platform
4.2.2 Flow Description
Purpose
To create FTP user for BOSS system to obtain CDR
Prerequisites
The installation of Server-u is completed.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 24
Personnel
ZXIN10 SACP engineering implementation personnel
Procedure Description
1. Create FTP user.
Start server-u and put the cursor on Serv-U via Servers > Domains >
Users. Then click the right mouse button and select New User to create
FTP user, as shown in Figure 4.2-2.
Figure 4.2-2 Creating FTP User
To create FTP user, it is required to set up user name, password, home
directory, and decide whether to lock the user in home directory. The
home directory for the user is the storage directory of CDR, which is also
the ftpputdir value configured for [ftpap*] section in the file imp.ini. The
user information after the user is created is shown in Figure 4.2-3.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 25
Figure 4.2-3 FTP User Information
2. Set up the rights for user home directory.
Click FTP user on the interface of server-u, and select Dir Access on the
user information interface to set up directory rights and file rights. Select
Read for Files and List for Directories, as shown in Figure 4.2-4.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 26
Figure 4.2-4 Setting up User Directory Rights
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 27
Chapter 5 Configure ZTE-HA Cluster
5.1 General
This chapter introduces the configuration of ZTE-HA cluster server.
Section 2 explains the whole configuration process of ZTE-HA.
5.2 Configuration Flow Description
5.2.1 Flow Chart
Config Heartbeat
Start
Config Cluster Resource
Config User Resource
End
Figure 5.2-1 Configuration Flow Chart for CDR Server Platform
5.2.2 Flow Description
Purpose
To configure cluster server for CDR to enhance system reliability
Prerequisites
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 28
The installation of ZTE-HA is completed.
Personnel
ZXIN10 SACP engineering implementation personnel
Procedure Description
Click Start > Program > Tools > Start Cluster Operation to start Cluster
Service on the active/standby server.
1. Configure heartbeat address.
Firstly, on the active server, click View > Private Net; Private Net >
TCP/IP Socket. Select heartbeat IP and use the default values for other
parameters. Then, click Add, as shown in Figure 5.2-2.
Figure 5.2-2 Configuring Heartbeat IP on Active Server
Configure heartbeat on the standby server, as shown in Figure 5.2-3.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 29
Figure 5.2-3 Configuring Heartbeat IP on Standby Server
After the configuration of heartbeat is completed, it can be viewed that
the heartbeat communication is normal on both active and standby
servers, as shown in Figure 5.2-4.
Figure 5.2-4 Normal Heartbeat Communication
2. Configure cluster resource.
Add cluster resource. The following operations only need to be executed
on one server. Click View > Resource Objects and switch to resource
view.
(1) Add shared disk volume resource.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 30
Right-click the mouse button on zx027001217 and select Create
Resource > Volume, as shown in Figure 5.2-5.
Figure 5.2-5 Creating Shared Volume Group
Configure shared disk volume, as shown in Figure 5.2-6.
Figure 5.2-6 Configuring Shared Disk Volume
Click Create to create the shared volume resource.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 31
(2) Bring the shared disk into cluster. Click the right mouse button on
Volume K:, and select Bring in Cluster, as shown in Figure 5.2-7.
Figure 5.2-7 Bringing in Cluster
Note:
After bringing in cluster, the user can only visit K: on the active server. K is the
drive letter for the shared volume. The state of resource is shown in Figure
5.2-8.
Figure 5.2-8 State of the shared volume resource
(3) Add floating IP address resource. Click the right mouse button on
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 32
zx027001217, and select Create Resource > IP Address. Configure IP
address resource, as shown in Figure 5.2-9. Bring in floating IP address
resource.
Figure 5.2-9 Configure IP Resource
3. Configure user resource.
Add user resource. Click the right mouse button on zzx027001217, and
select Create Resource > User Defined. Configure the user resource
information, as shown in Figure 5.2-10. Bring in user resource.
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 33
Figure 5.2-10 Configure User Resource
ZXIN10 SACP CDR Server Installation Guide Internal Use Only▲
All Rights reserved, No Spreading abroad without Permission of ZTE 34
Chapter 6 Verify CDR Server
6.1 General
This chapter introduces the verification of CDR server and the interconnection
between CDR and other network element.
Section 2 explains the verification of CDR server.
6.2 Verifying CDR server
Purpose
To verify if the installation and configuration of CDR server is correct
Prerequisites
The installation and configuration of CDR is completed. There is CDR
generated on SCP.
Personnel
ZXIN10 SACP engineering implementation personnel
Procedure Description
1. Log on to CDR server and enter the CDR storage directory which is
configured in [ftpap] section of imp.ini. Verify if there is file in
in01_G_101_* format under the directory.
2. Connect to CDR server via FTP tools to verify if the CDR file can be
downloaded from the CDR storage directory.