ZN-1000-ZBS Product Specification IEEE 802.11a/b/g/n Wireless Smart AP HW: 0.3 2 / 22

1Revision History DateVersionAuthorDescription 2013/07/01V0.1Iris1st draft version 2013/0709V0.2Iris2nd draft version Review for Main board power spec 2013/8/23V0.3IrisUpdatedtheSystemLEDLightsBehaviors Definition 2Specification 2.1Hardware Specification (Main Board + AHIC ANT Control Board) The Hardware specifications of the product are as below: Table 2-1 Hardware Specification of Main Board Features Additional Information Hardware Chipset SolutionCPUAR9342 RFAR9382 PHY : AR8035 CPU533MHz DDRII64Mbyte FLASH16Mbyte Ethernet PHY10/100/1000Mbps LED definitionSystem LED Light Behavior Definition Power supply-Support POE 802.3 at -Support +48V PTE 2 / 22 Power requirement -Output: +48V DC@0.83A -Input: 90~264V AC, 50/60Hz Anti-static Grade-Contact discharge: 6KV -Air discharge: 8KV Surge CapacityEthernet Line to Earth 2kv Line to Line 1kv Data rate-802.11a: 6/9/12/18/24/36/48/54 Mbps & Auto fallback -802.11b: 1/2/5.5/11 Mbps & Auto fallback -802.11g: 6/9/12/18/24/36/48/54 Mbps & Auto fallback -802.11n:6/6.5/13/13.5/19.5/26/27/39/40.5/52/54/58.5/65/ 78/81/104/108/117/121.5/130/135/ 162/ 216/ 243/ 270/ 300Mbps Data modulation type -IEEE 802.11 a/b/g DSSS (DBPSK, DQPSK, CCK) OFDM (BPSK, QPSK, 16-QAM, 64-QAM) -IEEE 802.11n OFDM (BPSK, QPSK, 16-QAM, 64-QAM) Current consumption (Input 48V) 25.5W RF1 2.4G 500mW (U.FL compliance connectors) Output power @ 25 (per chain 1.5dBm) 11b11g 27dBm@1Mbps 27 dBm@2Mbps 27dBm@5.5Mbps 27dBm@11Mbps 27dBm@6Mbps 27dBm@9Mbps 27dBm@12Mbps 27dBm@18Mbps 27dBm@24Mbps 27dBm@36Mbps 27dBm@48Mbps 24dBm@54Mbps 11gn(Per chain) HT20HT40 27dBm@MCS0/8 27dBm@MCS1/9 27dBm@MCS2/10 27dBm@MCS3/11 27dBm@MCS0/8 27dBm@MCS1/9 27dBm@MCS2/10 27dBm@MCS3/11 3 / 22 27dBm@MCS4/12 27dBm@MCS5/13 27dBm@MCS6/14 24 dBm@MCS7/15 27dBm@MCS4/12 27dBm@MCS5/13 27dBm@MCS6/14 24 dBm@MCS7/15 Sensitivity @ 2 chains 11b11g -94dBm@1Mbps -92dBm@2Mbps -91dBm@5.5Mbp -88dBm@11Mbps -92dBm@6Mbps -91dBm@9Mbps -88dBm@12Mbps -86dBm@18Mbps -83dBm@24Mbps -79dBm@36Mbps -74dBm@48Mbps -73dBm@54Mbps 11gn HT20HT40 -86dBm@MCS0/8 -83dBm@MCS1/9 -81dBm@MCS2/10 -78dBm@MCS3/11 -74dBm@MCS4/12 -70dBm@MCS5/13 -69dBm@MCS6/14 -68dBm@MCS715 -83dBm@MC0/S8 -80dBm@MCS1/9 -78dBm@MCS2/10 -75dBm@MCS3/11 -71dBm@MCS4/12 -67dBm@MCS5/13 -66dBm@MCS6/14 -65dBm@MCS7/15 RF2 5.8G 500mW (R-MMCX compliance connectors) Output power @ 25 (per chain 1.5dBm) 11a 5180MHz~5740MHz 20dBm@6Mbps 20dBm@9Mbps 20dBm@12Mbps 20dBm@18Mbps 20dBm@24Mbps 20dBm@36Mbps 20dBm@48Mbps 20dBm@54Mbps 5745MHz~5850MHz 24dBm@6Mbps 24dBm@9Mbps 24dBm@12Mbps 24dBm@18Mbps 24dBm@24Mbps 24dBm@36Mbps 4 / 22 24dBm@48Mbps 22dBm@54Mbps 11an(Per chain) Freq.HT20HT40 5180MHz~ 5740MHz 20dBm@MCS0/8 20dBm@MCS1/9 20dBm@MCS2/10 20dBm@MCS3/11 20dBm@MCS4/12 20dBm@MCS5/13 20dBm@MCS6/14 20dBm@MCS7/15 20dBm@MCS0/8 20dBm@MCS1/9 20dBm@MCS2/10 20dBm@MCS3/11 20dBm@MCS4/12 20dBm@MCS5/13 20dBm@MCS6/14 20dBm@MCS7/15 5745MHz~ 5850MHz 23.5dBm@MCS0/8 23.5dBm@MCS1/9 23.5dBm@MCS2/10 23.5dBm@MCS3/11 23.5dBm@MCS4/12 23.5dBm@MCS5/13 23.5dBm@MCS6/14 23.5dBm@MCS7/15 24dBm@MCS0/8 24dBm@MCS1/9 24dBm@MCS2/10 24dBm@MCS3/11 24dBm@MCS4/12 24dBm@MCS5/13 24dBm@MCS6/14 22dBm@MCS7/15 Sensitivity @2 chains 11a -92dBm@6Mbps -91dBm@9Mbps -88dBm@12Mbps -86dBm@18Mbps -83dBm@24Mbps -79dBm@36Mbps -74dBm@48Mbps -73dBm@54Mbps 11an HT20HT40 -86dBm@MCS0/8 -83dBm@MCS1/9 -81dBm@MCS2/10 -78dBm@MCS3/11 -74dBm@MCS4/12 -70dBm@MCS5/13 -69dBm@MCS6/14 -68dBm@MCS7/15 -83dBm@MCS0/8 -80dBm@MCS1/9 -78dBm@MCS2/10 -75dBm@MCS3/11 -71dBm@MCS4/12 -67dBm@MCS5/13 -66dBm@MCS6/14 -65dBm@MCS7/15 5 / 22 Table 2.1.1 General Specification of AHIC ANT Control Board FeaturesAdditional Information Chip set solutionCPLD: 5M240ZT100I5N RF Path Design1 to 4 RF Switch design *2 Standard compliance - IEEE 802.3u MDI / MDIX 10/100 Base-T Ethernet & IEEE 802.ab 1000 Base-T Ethernet Interfaces - 2 RJ45 support 10/100/1000MbpsFor 1*POE In + 1*POE Out - 1 MINI DIN JACK MDG-06-NS DIP 6PIN BlackFor Console - 1BOXHeaderDualStraight2x52.54mm180DIPForDigital Control - 1 Header Male 1x4 P=2.0mm 180 White TIN DIP - 2HeaderMale1x2P=2.54mm180BlackDIPConsole*1For connect with Main board + 1* External Power Supplier Light RJ45 portsupport 10/100/1000Mbps Restore buttonReset to factory default RF Frequency Range FCC : 2412-2472MHz CE:2412-2472MHz SRRC2412-2472MHz RFcharacteristic RF SWIsolation50dB Insertion Loss1.5dB Disable Diode Isolation30dB Enable Chain 1 Diode Insertion Loss3dB EVM0.6% Enable Chain 2 Diode Insertion Loss6dB EVM0.6% Enable Chain 3 Insertion Loss8dB EVM0.6% 6 / 22 Diode Enable Chain 4 Diode Insertion Loss10dB EVM0.6% 2.2Firmware Specification The Firmware Specifications of ZC-3101 as below: ZC-3101 is based on Atheros AR9342 network processor with 32 MBytes SDRAM memory and 16 MBytes flash memory. It is reliable and can work well in wide temperature range. It is suitable for use in many embedded applications such as high performance outdoor AP, high performance wireless print server,etc. It is an IEEE 802.11 a/b/g/n Wireless device, high throughput. Table 1-1 Firmware Specification 7 / 22 Feature / CertificationZC-3101 Standard Networking Wireless Networking Compatibility IEEE 802.11N IEEE 802.11A IEEE 802.11B IEEE 802.11G RF Card Optional Two RF Card support Access Point Mode Auth mode Open system Shared key 802.1x WPA WPA2 WPA&WPA2 WPA-PSK WPA2-PSK WPA-PSK & WPA2-PSK Encryption TKIP AES WEP 64 bit Encryption 128 bit Encryption 152 bit Encryption Key Type Passphrase Key1 Key2 Key3 8 / 22 Key4 Hex SSID (Service Set Identifier)SSID Broadcast Disable Multiple SSIDs/VAP/VLAN Settings(Max. 16) Each SSID has its own security mode Restrict Access by MAC (ACL) Local MAC Radius MAC Wireless Client Isolation QoS (802.11e) / WMM MAX Station Number(0-32) AP Flow Control(Tx) DFS DFS(Bridge) Beacon Interval (20-1024) Station Adapter Mode Multi-Client MAC Clone LAN to LAN Site Survey Uplink Speed Control(Tx) control by AP Auth Mode Open system Shared key WPA-PSK WPA2-PSK 802.1X-Only (WPA-Enterprise) WPA (WPA-Enterprise) WPA2 (WPA2-Enterprise) Encryption TKIP 9 / 22 AES WEP 64 bit Encryption 128 bit Encryption 152 bit Encryption Auto Search AP Wireless Distribution System (WDS) Point to Point Bridge Point to Point Multi-bridge(MAX:4) Encryption TKIP AES WEP 64 bit Encryption 128 bit Encryption 152 bit Encryption Uplink Speed Control(Tx) WDS Separation Output Power Control(Step by 1dBm) Antenna (1,200 unique antenna patterns) Antenna Gain Channel / Frequency Data Rate Selection Data Rate Selection(Client) Extension Channel Wirelss channel mode(20MHz/40MHz) Wirelss channel mode(5MHz/10MHz) HT Protect A-MPDU aggregation A-MSDU aggregation short GI Advanced Settings RTS Threshold (0-2347) 10 / 22 Fragmentation Threshold(256~2346)DTIM Interval (1-255) Preamble Type(long and short) IGMP Snooping Space In Meter Regatta Mode Extension channel protection mode RIFS Link Integration TDM Coordination Layer 3 / Layer 4 Routing DHCP Server DHCP Relay PPPoE Firewall Source IP Filtering Destination IP Filtering Source Port Filtering Destination Port Filtering Port For wading DMZ Traffic Shaping Incoming/Out coming Limit Incoming/Out coming Burst IP Protocol (RFC 791) Static DHCP Client DNS Layer 2 Ethernet Bridging Spanning Tree Protocol (IEEE 802.1d) Virtual LAN ID (802.1q) Management VLAN ID Ethernet Data Rate 11 / 22 Secondary RJ45 Power Security RADIUS Client (RFC2865-2866)EAP-LEAP EAP-TLS EAP-TTLS EAP-PEAP System Management Management Interfaces Management Privacy Mode WEB UI management SNMP WISE Login Web UI Login SSH Login Management Protocols Telnet access to command line interface (RFC 854-861) Capability to restrict to SSH Embedded Web Server for web based management Capability to restrict to HTTPS Capability to restrict to SSL Multi-session support Upgrade firmware via Web Browser FTP Server upload for software upload and download for configuration NTP Client Automatic Daylight Saving Adjustment Manual Daylight Saving Adjustment Configuration Management Capability to store configuration backup Configuration changes via: 12 / 22 Local command line Remote command lineSSH Web interface Capability to Restore factory (or service provider) defaults via Web via push button SNMP for status and event notification SNMP v1 (RFC 1157) SNMP v2c (RFC 2011-2013) SNMP v3 (RFC 2571-2576) user name and password authentication type encrytion type SNMP trap transmit SNMP Location CoovaChilli RADIUS Server RADIUS Server Administrative-User Captive Portal Fault Management Event Logging SYSLOG (RFC 3164) Delivery Performance Management Statistics Ethernet Wireless Connection State Management Statistics Wireless and Wired Port statereal-time display of uplink/downlink speedNetwork Activities System State CPU Usage Memory UsageRouter State 13 / 22 ARP Table Bridge Table DHCP Clients Security Management Password protected configuration or management sessions for web or console access Configurable SNMP community string GPS Coordinate Chrome Support Tools Site Survey Ping Watchdog Data Rate Test Antenna Alignment Speed Test AirView OEM Settings Logo Image Output Power Limit Channel List Limit(Debug Country) DFS Model Name MAC Address 14 / 22 2.3Power Adapter Specification -Support POE 802.3 at -Support +48V PTE2.4Physical specification The Physical specifications of the product are as below: Table 2-4 Physical Specification ItemsDescription Dimension 242.05 x242.05x140.95mm WeightTBC EnclosureIP67 2.5Environment specification The Environment specifications of the product are as below: Table 2-5 Environment Specification ItemsDevice DescriptionPower Supply Spec Operating Temperature(Max)-20 ~ +55C TBD Operating Humidity (non-condensing)10 to 95% RHTBD Storage Temperature-40 ~ +70CTBD Storage Humidity (non-condensing)10 to 95% RHTBD Warranty12 Months GreenRoHs/REACH Compliant 15 / 22 2.6Safety/Country Approval We will do EMI/EMC pre-test according to the following items:Table 2-6 Safety/Country Approval ItemsDescriptionID numberCE/FCCDetails specTBD SRRC(High Band)Details specTBD SurgeDetails specTBD ESD Details specTBD EFT Details specTBD 2.7Packaging Specification The following items will be required for the complete packaging of the ZC-3101: Table 2-7 Package ItemComments CartonTBD Gift Box / CushionTBD Power Supply NA PoEinjector Support POE 802.3 at / 48V PT Steel Cable TieTBD 16 / 22 3Mechanical Spec 3.1Device Outline DrawingDefault Housing Color is White Details Dimensions - TBD 3.2Assy Drawing TBD 17 / 22 3.3Antenna Product Spec & DrawingElectrical Specification Vertical Polarization NOItemsSpecifications 1Antenna component MaterialPCB 2Frequency Band2.4GHz~2.5GHz 3Power Handling1w (cw) 4Impedance50 5VSWR< 2.0:1 6PolarizationLinear 7Antenna Peak Gain7.5dBi 8 HPBW_Horizontal NA 9 HPBW_Vertical NA 10 Front to Back RatioNA 11Side-lobeNA 12 Cross-Polarization NA 13RF CableOd 1.37mm * L 200 mm 14RF Cable ConnectorIPEX (MHF) 15CoreNA Horizontal Polarization 18 / 22 NOItemsSpecifications 1Antenna component MaterialPCB 2Frequency Band2.4GHz~2.5GHz 3Power Handling1w (cw) 4Impedance50 5VSWR< 2.0:1 6PolarizationLinear 7Antenna Peak Gain7.5dBi 8 HPBW_Horizontal NA 9 HPBW_Vertical NA 10 Front to Back RatioNA 11Side-lobeNA 12 Cross-Polarization NA 13RF CableOd 1.37mm * L 200 mm 14RF Cable ConnectorIPEX (MHF) 15CoreNA RX Assistance ANTNOItemsSpecifications 19 / 22 1Antenna component Materialmetal 2Frequency Band2.4GHz~2.5GHz 3Power Handling1w (cw) 4Impedance50 5VSWR< 2.0:1 6PolarizationLinear 7Antenna Peak Gain3dBi 8 HPBW_Horizontal NA 9 HPBW_Vertical NA 10 Front to Back RatioNA 11Side-lobeNA 12 Cross-Polarization NA 13RF CableOd 1.13mm * L 200 mm 14RF Cable ConnectorIPEX (MHF) 15CoreNA Environmental & Mechanical Characteristics NOItemsSpecifications 1Operating Temperature-10 C ~ +60 C 20 / 22 2Storage Temperature-10 C ~ +70 C 4Label4.1LED LENS Spec TBD 5Pin Assignment And Dimension of DiP Connector TBD