ZL10AVR - BTCdl.btc.pl/kamami_com/zl10avr_en.pdf · socket suitable for selected microcontroller....

Versatile Evaluation Board for AVR Microcontrollers

ZL10AVR

ver. 3.0

Thank you for buying ZL10AVR evaluation

board. We hope that the power and quality

of our tool allow you to appreciate the

advantages of AVR microcontrollers (AT90S,

ATmega and ATtiny families).

http://www.kamami.com/

ZL10AVR – Versatile Evaluation Board for AVR Microcontrollers

IntroductionZL10AVR is a versatile evaluation board designed for engineers and hobbyists who want to prototype systems based on AVR microcontrollers (AT90S, ATmega and ATtiny families in DIP8, DIP20, DIP28 and DIP40 packages). ZL10AVR is equipped with 7 DIP sockets suitable for most of AVR family microcontrollers. LEDs mounted near sockets indicate socket suitable for selected microcontroller. Developer has access to all microcontroller pins (only one microcontroller can be installed at the same time!), which are brought to gold-pin connectors. Board's configuration is complete, user can find on the board following components: USB interface connector (for ZL1USB module), analog potentiometer, 8 MHz crystal oscillator, 4 LED displays, buzzer, RS232 interface with DB9F connector, 4x4 LED matrix, configurable keyboard (1x4 or 4x4 buttons), 8 LEDs, RC5 infrared receiver with TTL output, ISP connector and socket for LCD display (2x16 characters). Thanks to simple PLD logic (from Xilinx) incorporated on the board, most of integrated peripherals can be easy and comfortably connected to any port (PORTA, PORTB, PORTC or PORTD) available in microcontroller used in the application. The gold-pin headers provide access to easy connection of matrix keyboard and matrix display. ZL10AVR board comes with examples of Bascom programs.

Features► Compatible with most of AVR family microcontrollers (AT90S, ATmega, ATtiny families)► RS232 interface (with level converter and DB9F connector)► 4-digit, 7-segment, multiplexed LED common cathode display► Socket for LCD 2 x16 character display (LCD1602 module)► 8 LEDs► 16 LEDs configured as 4x4 matrix ► Configurable microswitch 4x4 or 4x1 keyboard► Integrated infrared RC5 receiver with TTL output► Buzzer► Socket for USB interface (ZL1USB_A module)► ISP Kanda STK200 compatible connector (recommended ISP programmer: ZL2PRG)► Analog potentiometer► Reset pulse generator► Integrated regulated power supply ► Supply 9 VDC/250 mA► Built-in 3,3 V voltage regulator► Easy access to regulated +3,3 V and +5 V power supply for external devices

Supported microcontrollersDevices supported by ZL10AVR:

► AT90: AT90S1200, AT90S2313, AT90S2323, AT90S2343► ATtiny: ATtiny11, ATtiny12, ATtiny13, ATtiny15, ATtiny25, ATtiny26, ATtiny45, ATtiny85, ATtiny2313► ATmega: ATmega8, ATmega16, ATmega32, ATmega48, ATmega88, ATmega161, ATmega162, ATmega163,

ATmega164, ATmega168, ATmega323, ATmega324, ATmega644, ATmega8515, ATmega8535

ZL10AVR board is compatible with most of new AVR microcontrollers in DIP8/20/28 and DIP40 packages.

Code Description

ZL10AVR ► ZL10AVR board (without microcontrollers and LCD display) 1 pcs.

Contents of the package

DisclaimerBTC Korporacja makes no warranty for the use of its products and assumes no responsibility for any errors which may appear in this document nor does it make a commitment to update the information contained herein. BTC Korporacja products are not intended for use in medical, life saving or life sustaining applications. BTC Korporacja retains the right to make changes to these specifications at any time, without notice.All product names referenced herein are trademarks of their respective companies.

BTC Korporacja05-120 Legionowo, Polandul. Lwowska 5e-mail: [email protected]://www.kamami.com

Technical assistanceFor technical assistance, please contact [email protected] provide the following data:► Version of the operating system► Microcontroller type used in your system and its oscillator frequency► Detailed description of the problem


ZL10AVR – Versatile Evaluation Board for AVR Microcontrollers 3

Contents► Board configuration .................................................................................................................................................4

► Board layout .............................................................................................................................................................5

► Microcontroller configuration ..................................................................................................................................6

► 7-segment LED display .........................................................................................................................................10

► LEDs ......................................................................................................................................................................12

► Alphanumeric LCD display ...................................................................................................................................13

► Analog potentiometer .............................................................................................................................................14

► Buzzer ....................................................................................................................................................................15

► RS232/USB interface .............................................................................................................................................16

► IR receiver ..............................................................................................................................................................18

► Matrix LED display ...............................................................................................................................................19

► Microswitch keyboard ...........................................................................................................................................20

► I/O headers .............................................................................................................................................................21

► ISP connector .........................................................................................................................................................22

► Schematics .............................................................................................................................................................23


ZL10AVR – Versatile Evaluation Board for AVR Microcontrollers4

Board configurationBlock schematic of ZL10AVR board is shown below. Logic module integrated in CPLD works as a multiple switch simplifying connections between microcontroller’s ports and 7-segment multiplexed display, 8 LEDs and ISP con-nector.

Peripherals like: crystal resonator, potentiometer, buzzer, IR receiver, RS232 interface, USB interface can be con-nected/disconnected to/from microcontroller with few dedicated jumpers.

Only one microcontroller at the time can be used with ZL10AVR board!

Block schematic of ZL10AVR board



Board layout



Microcontroller configurationActive socket is selected by jumper mounted on JP21 switch.

JP21 closed pins Active sockets

1-2 U4

2-3 U2, U3, U5, U6

3-4 U1, U7

Active (selected) socket is indicated by LED. Microcontrollers that can be used with specific sockets are shown below.

Socket Microcontroller

U1 ATtiny 26

U2 ATmega 32, ATmega 323, ATmega 16, ATmega 163, ATmega 8535, ATmega 164, ATmega 324, ATmega 644

U3 ATmega 8515, ATmega 161, ATmega 162

U4 ATmega 8, ATmega 48, ATmega 88, ATmega 168

U5 ATtiny 2313

U6 AT90S1200, AT90S2313

U7 ATtiny 11, ATtiny 12, ATtiny 13, ATtiny 15, ATtiny 25, ATtiny 45, ATtiny 85, AT90S2323, AT90S2343

Note! ATtiny 11/15 are not ISP programmable.



Crystal oscillator can be disconnected from X1 and X2 pins in U1, U4 and U5 sockets. Recommended configura-tions of jumpers JP9, JP10 (U1 socket), JP2, JP3 (U5 socket) and JP5, JP6 (U4 socket) are shown below.

Jumpers ascribed to U1 crystal pins

JP9 closed pins JP10 closed pins Crystal X1…

1-2 1-2 …connected to X1 i X2 of U3 socket

2-3 2-3 …disconnected

1-2 2-3 Not allowed

2-3 1-2 Not allowed





1-2 2-3 Not allowed

2-3 1-2 Not allowed





1-2 2-3 Not allowed

2-3 1-2 Not allowed

Jumpers JP1 (socket U7), JP4 (socket U5), JP7 (socket U4) and JP11 (socket U1) are used to connect microcon-troller RESET input to reset signal generator (U10), manual reset button S1 and RESET signal generated by ISP programmer. Recommended configurations of these jumpers are shown below.

Configurations of JP1

JP1 closed pins External (global) RESET signal…

1-2 …connected to U7

2-3 …disconnected from U7





Only one (active) socket can be connected to crystal generator and global RESET signal. In other case microcontroller will work incorrectly!











Examples of board configurationsATmega32, external resonatorMicrocontroller in U2 socket. Jumpers configuration: JP21 (SOCKET) – 2-3 (U2/3/5/6) JP11 (U1 GRES) – 2-3 (Off) JP9 (U1 CRYST) – 2-3 (Off) JP10 (U1 CRYST) – 2-3 (Off) JP5 (U4 CRYST) – 2-3 (Off) JP6 (U4 CRYST) – 2-3 (Off) JP7 (U4 GRES) – 2-3 (Off) JP2 (U5 CRYST) – 2-3 (Off) JP3 (U5 CRYST) – 2-3 (Off) JP4 (U5 GRES) – 2-3 (Off) JP1 (U7 GRES) – 2-3 (Off)

ATtiny2313, external resonatorMicrocontroller in U5 socket. Jumpers configuration: JP21 (SOCKET) – 2-3 (U2/3/5/6) JP11 (U1 GRES) – 2-3 (Off) JP9 (U1 CRYST) – 2-3 (Off) JP10 (U1 CRYST) – 2-3 (Off) JP5 (U4 CRYST) – 2-3 (Off) JP6 (U4 CRYST) – 2-3 (Off) JP7 (U4 GRES) – 2-3 (Off) JP2 (U5 CRYST) – 1-2 (On) JP3 (U5 CRYST) – 1-2 (On) JP4 (U5 GRES) – 1-2 (On) JP1 (U7 GRES) – 2-3 (Off)

ATtiny2313, internal oscillatorMicrocontroller in U5 socket. Jumpers configuration: JP21 (SOCKET) – 2-3 (U2/3/5/6) JP11 (U1 GRES) – 2-3 (Off) JP9 (U1 CRYST) – 2-3 (Off) JP10 (U1 CRYST) – 2-3 (Off) JP5 (U4 CRYST) – 2-3 (Off) JP6 (U4 CRYST) – 2-3 (Off) JP7 (U4 GRES) – 2-3 (Off) JP2 (U5 CRYST) – 2-3 (Off) JP3 (U5 CRYST) – 2-3 (Off) JP4 (U5 GRES) – 1-2 (On) JP1 (U7 GRES) – 2-3 (Off)

ATmega8, external resonatorMicrocontroller in U4 socket. Jumpers configuration: JP21 (SOCKET) – 1-2 (U4) JP11 (U1 GRES) – 2-3 (Off) JP9 (U1 CRYST) – 2-3 (Off) JP10 (U1 CRYST) – 2-3 (Off) JP5 (U4 CRYST) – 1-2 (On) JP6 (U4 CRYST) – 1-2 (On) JP7 (U4 GRES) – 1-2 (On) JP2 (U5 CRYST) – 2-3 (Off) JP3 (U5 CRYST) – 2-3 (Off) JP4 (U5 GRES) – 2-3 (Off) JP1 (U7 GRES) – 2-3 (Off)



7-segment LED displaySegments of LED displays can be controlled by one of four microcontroller I/O ports (8 lines each): PORTA, PORTB, PORTC or PORTD. Active port is selected by JP17 (LED_DSP) simultaneously with display’s cathodes drivers. Cathodes are controlled by 4 LSB lines of PORTA, PORTB, PORTC or PORTD.

LED displays port selection (JP17 - LED_DSP)

JP17 closed pins Segments controlled by… Cathodes controlled by (MSD…LSD)…

1-2 …PA …PB(3…0)

2-3 …PB …PC(3…0)

3-4 …PC …PD(3...0)

4-5 …PD …PA(3...0)

Displays segments are connected to I/O port lines as shown below.

Connection of LED diplays segments

Displays segment I/O line (x=A/B/C/D)

A Px0

B Px1

C Px2

D Px3

E Px4

F Px5

G Px6

DP Px7

DIP-switch S2 selects number of active displays (non-active displays can be switched-off).



LEDsLEDs can be connected to one of four ports: PORTA, PORTB, PORTC or PORTD. Active port is selected by JP22.

LEDs port selector (JP22)

JP22 closed pins LEDs controlled by…

1-2 …PA

2-3 …PB

3-4 …PC

4-5 …PD



Alphanumeric LCD displayStandard LCD display with HD44780 compatible controller (LCD1602 module) can be mounted in W1 socket. Connections between microcontroller and display module lines are show below.

Connections between microcontroller and display module

LCD module signal name LCD module pin AVR I/O lines

RS 4 PB0

RW 5 PB1

E 6 PB2

D0 7 PD0

D1 8 PD1

D2 9 PD2

D3 10 PD3

D4 11 PD4

D5 12 PD5

D6 13 PD6

D7 14 PD7



Analog potentiometerZL10AVR board is equipped with analog potentiometer R8 allowing to regulate select form 0 up to +5 V. Potentiometer can be connected to analog input on line PA0 or PC0 as shown below.

Analog potentiometer configurations

JP24 closed pins JP25 closed pins * Potentiometer R8…


1-2 2-3 …connected to PA0


2-3 2-3 …connected to PC0

* There is an error on Top Overlay: potentiometer R8 is disconnected, when jumper JP25 is in position On (closed pins 1-2). Potentiometer R8 is connec-ted, when jumper JP25 is in position Off (closed pins 2-3).



BuzzerBuzzer Gl1 can be connected to PB0 line. Jumper JP23 (SPEAKER) disconnects buzzer.

Buzzer connection

JP23 closed pins Gl1…

1-2 (On) …connected to PB0

2-3 (Off) …disconnected



RS232/USB interfaceZL10AVR board is equipped with:

► DB9F connector connected to MAX232-compatible voltage converter (RS232 interface),► JP15 socket for USB2RS232 interface module (recommended type is ZL1USB).Serial interfaces are configured by JP8, JP12, JP13 and JP14 jumpers.

Serial ports configurations

JP8 closed pins

JP12 closed pins Selected… JP13 closed

pinsJP14 closed

pins TxD… RxD… Configuration

– – – 1-2 1-2 …disconnected …disconnected Serial interface disconnected

– 1-2 …channel RxD RS232 1-2 2-3 …disconnected …connected to PD0 –

– 2-3 …channel RxD USB 1-2 2-3 …disconnected …connected to PD0 –

1-2 – …channel TxD RS232 2-3 1-2 …connected to PD1 …disconnected –

2-3 – …channel TxD USB 2-3 1-2 … connected to PD1 …disconnected –

1-2 1-2 …RS232 (TxD and RxD) 2-3 2-3 … connected to PD1 …connected to PD0 RS232 interface

connected to microcontroler

2-3 2-3 …USB (TxD and RxD) 2-3 2-3 … connected to PD1 …connected to PD0 USB2RS232 interface

connected to microcontroler

Note! Yellow colour marks recommended jumper positions.



IR receiverZL10AVR board is equipped with TFMS5360 (U12) IR receiver. Possible connections of its output are shown below.

Configurations of JP19 and JP20

JP19 closed pins JP20 closed pins IR receiver output…

1-2 1-2 …connected to PD2

1-2 2-3 …connected to PB6

2-3 – …disconnected



Matrix LED displayMatrix (4x4 LEDs) LED display mounted on the ZL10AVR is connected to I/O port with 16 wires IDC ribbon ca-ble (not included). Connections of rows and columns of LEDs matrix is shown below. We recommend to use only one LED in each row at the time, to avoid lumination intensity modulation.



Microswitch keyboardZL10AVR board is equipped with 16 microswitches connected as 4x4 matrix or simple 4x1 keyboard (with „0” logic level active). Keyboard can be connected to any accesible I/O microcontroller port with IDC ribbon cable (zl5 gold-pin header).


JP26 closed pins Keyboard configuration is…

1-2 …simply 4 x 1 switches

2-3 …matrix 4 x 4



I/O headers



ISP connectorPin layout of ISP connector (JP16, Kanda STK200 compatible) is shown below. Kamami recommends using ZL2PRG ISP programmer (for PC with parallel port) or KamProg for AVR (for PCs with USB).

ISP connector pins



Schematics

ZL10AVR - BTCdl.btc.pl/kamami_com/zl10avr_en.pdf · socket suitable for selected microcontroller....

Documents

Transcript of ZL10AVR - BTCdl.btc.pl/kamami_com/zl10avr_en.pdf · socket suitable for selected microcontroller....