7/29/2019 ZenD_11-12-13_(Body_Care)

http://slidepdf.com/reader/full/zend11-12-13bodycare 1/1

BODY WORK CARE

BODY WORK CARE

107

BODY WORK CARE

Corrosion Prevention 11-1

Vehicle Cleaning 11-2

CORROSION PREVENTION

It is important to take good care of yourvehicle to protect it from corrosion.Listed below are instructions for how tomaintain your vehicle to prevent corrosion.Please read and follow these instructionscarefully.

Important Information About Corrosion

Common causes of corrosion1) Accumulation of road salt, dirt, moisture,

or chemicals in hard to reach areas ofthe vehicle underbody or frame.

2) Chipping, scratches and any damage to

treated or painted metal surfaces resultingfrom minor accidents or abrasion bystones and gravel.

Environmental conditions whichaccelerate corrosion1) Road salt, dust control chemicals, sea air

or industrial pollution will all accelerate thecorrosion of metal.

2) High humidity will increase the rate ofcorrosion particularly when thetemperature range is just above thefreezing point.

3) Moisture in certain areas of a vehicle foran extended period of time may promotecorrosion even though other body

sections may be completely dry.

11-1

4) High temperatures will cause anaccelerated rate of corrosion to parts ofthe vehicle which are not well ventilatedto permit quick drying.

This information illustrates the necessity ofkeeping your vehicle (particularly theunderbody) as clean and dry as possible. Itis equally important to repair any damage tothe paint or protective coatings as soon aspossible.

How to Help Prevent Corrosion

Wash your vehicle frequently

The best way to preserve the finish on yourvehicle and to help avoid corrosion is to keepit clean with frequent washing.Wash your vehicle regularly during the winterand immediately after the winter. Keep yourvehicle, particularly the underside, as cleanand dry as possible.If you frequently drive on salted roads, yourvehicle should be washed at least once amonth during the winter. If you live near theocean, your vehicle should be washed at leastonce a month throughout the year.For washing instructions, refer to the"VEHICLE CLEANING" section.

Remove foreign material depositsForeign material such as salts, chemicals, roadoil or tar, tree sap, bird droppings and industrial

fall-out may damage the finish of your vehicle

if it is left on painted surfaces. Remove thesetypes of deposits as quickly as possible. Ifthese deposits are difficult to wash off, anadditional cleaner may be required. Be surethat any cleaner you use is not harmful topainted surfaces and is specifically intendedfor your purposes. Follow the manufacturer'sdirections when using these special cleaners.

Repair finish damageCarefully examine your vehicle for damageto the painted surfaces. Should you find anychips or scratches in the paint, touch themup immediately to prevent corrosion fromstarting. If the chips or scratches have gonethrough to the bare metal, have a qualifiedbody shop make the repair.

Keep Passenger and luggagecompartments clean.Moisture, dirt or mud can accumulate underthe floor mats and may cause corrosion.Occasionally, check under these mats toensure that this area is clean and dry. Morefrequent checks are necessary if the vehicleis used off road or in wet weather.Certain cargos such as chemicals, fertilizers,cleaners, salts, etc., are extremely corrosiveby nature. These products should betransported in sealed containers. If a spill or

leak does occur, clean and dry the areaimmediately.

108

BODY WORK CARE

VEHICLE CLEANING

Store your vehicle in a dry, wellventilated

area.Do not park your vehicle in a damp, poorlyventilated area. If you often wash your vehiclein the garage or if you frequently drive it inwhen wet, your garage may be damp. The highhumidity in the garage may cause oraccelerate corrosion. A wet vehicle maycorrode even in a heated garage if theventilation is poor.

A WARNING

Do not apply additional undercoatingor rust preventive coating on or aroundexhaust system components such asthe exhaust pipes, etc. A fire could be

started if the undercoating substancebecomes overheated.

Cover your vehicleIf you cannot regularly park your vehicle in agarage, we recommend you use a vehiclecover. Years of exposure to midday sun cancause the colours in paint, plastic parts, andfabrics to fade. Covering your vehicle with ahigh-quality, "breathable" vehicle cover canhelp protect the finish from the harmful UVrays in sunlight, and can reduce the amountof dust and air pollution reaching t ie surface.

109

A WARNING

When cleaning the interior or exteriorof the vehicie, NEVER USE flammablesolvents such as lacquer thlnners,petrol, benzene or cleaning materialssuch as bleach or strong householddetergents. The materials could causepersonal injury or damage to thevehicle.

Cleaning the InteriorVinyl upholsteryPrepare a solution of soap or mild detergentmixed with warm water. Apply the solution tothe vinyl with a sponge or soft cloth and let itsoak for a few minutes to loosen dirt. Rub the

surface with a clean, damp cloth to removedirt and the soap solution. If some dirt stillremains on the surface, repeat this procedure.Fabric upholsteryRemove loose dirt with a vacuum cleaner.Using a mild soap solution, rub stained areaswith a clean damp cloth. To remove soap, rubthe areas again with a cloth dampened withwater. Repeat this until the stain is removed,or use a commercial fabric cleaner for tougherstains. If you use a fabric cleaner, carefullyfollow the manufacturer's instructions andprecautions.

Seat Belts

Clean seat belts with a mild soap and water.Do not use bleach or dye on the belts. Theymay weaken the fabric in the belts.

Vinyl floor matsOrdinary dirt can be removed from vinyl withwater or mild soap. Use a brush to help loosendirt. After the dirt is loosened, rinse the matthoroughly with water and dry it in the shade.

CarpetsRemove dirt and soil as much as possible witha vacuum cleaner. Using a mild soap solution,rub stained areas with a clean damp cloth. Toremove soap, rub the areas again with a clothdampened with water. Repeat this until the

stain is removed, or use a commercial carpetcleaner for tougher stains. If you use a carpetcleaner, carefully follow the manufacturer'sinstructions and precautions.

11-2

BODY WORK CARE

Cleaning the Exterior

CAUTION

K Is important that your vehicle be keptclean and free from dirt. Failure to keepyour vehicle clean may result in fadingof the paint or corrosion to various

parts of the vehicle body.

Washing

A WARNING

• Never attempt to wash and wax yourvehicle with the engine running.

• When cleaning the underside of thebody and fender, where there maybe sharp-edged parts, you shouldwear gloves and a longsleeved shirtto protect your hands and arms frombeing cut.

• After washing your vehicle, carefullytest the brakes before driving tomake sure they have maintainedtheir normal effectiveness.

When washing the vehicle, follow theinstructions below:

1) Flush the underside of body and wheelhousings with pressurized water toremove mud and debris. Use plenty ofwater.

CAUTIONWhen washing the vehicle, avoiddirecting steam or hot water of morethan 80°C (176°F) on plastic parts.

2) Remove dirt and mud from the bodyexterior with running water. You may usea soft sponge or brush. Do not use hardmaterials which can scratch the paint.

3) Wash the entire exterior with a milddetergent or car wash soap using asponge or soft cloth. The sponge or clothshould be frequently soaked in the soapsolution.

CAUTION

When using a commercial car washproduct, observe the cautionsspecified by the manufacturer. Neveruse strong household detergents orsoaps.

4) Once the dirt has been completelyremoved, rinse off the detergent withrunning water.

5) After rinsing, wipe off the vehicle bodywith a wet chamois or cloth and allow itto dry in the shade.

6) Check carefully for damage to painted

surfaces. If there is any damage,"Touchup" the damage following theprocedure below:a) Clean all damaged spots and allow

them to dry.b) Stir the paint and "touchup" the

damaged spots lightly using a smallbrush.

c) Allow the paint to dry completely.

WaxingAfter washing the vehicle, waxing andpolishing are recommended to further protectand beautify the paint.* Only use waxes and polishes of good

quality.

• When using waxes and polishes, observethe precautions specified by themanufacturers.

11-3 110

GENERAL INFORMATION

GENERAL INFORMATIONVehicle Identification 12-1

GENERAL INFORMATION

VEHICLE IDENTIFICATION

70F-10-001

Chassis Serial NumberThe chassis and/or engine serial numbers areused to register the vehicle. They are also

used to assist your dealer when ordering orreferring to special service information.Whenever you have occasion to consult yourMARUTI dealer, remember to identify yourvehicle with this number. Should you find thenumber difficult to read, you will also find it onthe identification plate.

70F-10-002

Engine Serial NumberThe engine serial number is stamped on thecylinder block as shown in the illustration and

also on the identification plate.

12-1 112

SPECIFICATIONS

SPECIFICATIONSSpecifications 13-1

113

SPECIFICATIONS

NOTE: 

Specifications are subject to change without notice.

DIMENSIONS

Overall lengthOverall widthOverall heightWheelbaseTread front

rearGround clearance

MASS (WEIGHT)

Kerb mass (weight)Gross vehicle mass (weight) ratingSeating Capacity

ENGINETypeNumber of cylindersBoreStrokePiston displacementCompression ratio

UNIT:mm

3 5351 4951 4052 3351335

1305165

UNIT:Kg

8501225

5 persons

Four-stroke cycle, 16 valve, water cooled (SOHC)4

77.0 mm82.0 mm1527 cm

3

23:1

13-1 114

SPECIFICATIONS

ELECTRICALIdle speed (rpm)BatteryFusesHeadlightTurn signal fightSide turn signal lightClearance lightTail/brake lightRegistration plate lightReversing light

WHEEL AND SUSPENSION

Tyre size, front and rearTyre pressures front

rearSuspension type front

rear

STEERINGToe-in

CAPACITIESCoolant(Including reservoir tank)Fuel tankEngine oilTransmission oil

850 ± 25 rpm38B20R (28AH/5HR)See "INSPECTION AND MAINTENANCE" section12V60/55W12V 21W12V 5W12V 5W12V 5/21W12V 5W12V 21W

145/70R1371S2.3 kg/cm2

2.1 kg/cnfStrutCoil spring

0±1 mm

6.0 L

35 L4.75 L (Replacement with Oil Filter)2.4 L

115 13-2

111