Building Web Services with Zend Framework (PHP Benelux meeting 20100713 Vlissingen)
ZenD 10 (Emergency Services)
-
Upload
15011977anand -
Category
Documents
-
view
216 -
download
0
Transcript of ZenD 10 (Emergency Services)
-
7/29/2019 ZenD 10 (Emergency Services)
1/1
EMERGENCY SERVICE
EMERGENCY SERVICE
Jacking Instructions 10-1
Jump Starting Instructions 10-2
Towing 10-4
Emergency Remedies 10-4
99
EMERGENCY SERVICE
JACKING INSTRUCTIONS
70F-04-020
1) Park the vehicle securely on hard levelground.
2) Choke the front and rear wheel diagonallyopposite the wheel to be changed.
3) Switch on the hazard warning flasher ifyour vehicle is in or near traffic.
4) Slacken but do not remove wheel nuts onthe wheel to be changed.
5) Position the jack vertically and raise thejack by turning the jack handle clockwiseuntil the jack head fits the front suspensionarm or the rear axle as shown overleaf.
70F-04-022 70F-08-001
CAUTION
Do not put the jack head on to thelateral rod (if equipped), or the lateralrod will be damaged.
6) Continue to raise the jack slowly andsmoothly until the tyre clears the ground.Do not raise the vehicle more thannecessary.
WARNING
Use the jack only to changewheels.
Never jack up the vehicle on aninclined surface.
Never raise the vehicle with thejack in a location other than the placespecified in the illustration near thewheel to be changed.
Make sure that the jack is raisedat least 2 Inches (51 mm) beforeit contacts the vehicle. Use of the
jack when it is within 2 inches ofbeing fully collapsed may result
in failure of the jack.
10-1 100
EMERGENCY SERVICE
JUMP STARTING INSTRUCTIONS
70F-08-002E 70F-08-003E
WARNING
Never get under the vehicle when itis supported by the Jack,
Never run the engine when thevehicle is supported by the jack andnever allow passengers to remain inthe vehicle.
Never attempt to jump start yourvehicle if the battery appears to befrozen. Batteries in this conditionmay explode or rupture if jumpstarting is attempted.
When making jump leadconnections, be certain that yourhands and the jump leads remainclear from pulleys, belts, or fans.
Batteries produce flammablehydrogen gas. Keep flames andsparks away from the battery or anexplosion may occur. Never smokewhen working in the vicinity of thebattery.
If the booster battery you use forjump starting Is installed In anothervehicle, make sure the two vehiclesare not touching each other.
If your battery dischargesrepeatedly, for no apparent reason,have your vehicle inspected by anauthorized MARUTI dealer.
101 10-2
EMERGENCY SERVICE
WARNING
To avoid harm to yourself or damageto your vehicle or battery, follow thejump starting instructions belowprecisely and in order. If you are in
doubt, call for qualified road service.
70F-08-004E
When jump starting your vehicle, use thefollowing procedure:1) Use only a 12 volt battery to jump start
your vehicle. Position the good 12V batteryclose to your vehicle so that the jumpleads will reach both batteries. When usinga battery installed on another vehicle, DONOT LET THE VEHICLES TOUCH. Applythe parking brakes fully on both vehicles.
2) Turn off all vehicle accessories, exceptthose necessary for safety reasons (forexample, headlights or hazard lights).
3) Make jump lead connections as follows:a) Connect one end of the first jump lead
to the positive (+) terminal of the flatbattery.
b) Connect the other end to the positive(+) terminal of the booster battery.
c) Connect one end of the second jumplead to the negative (-) terminal of thebooster battery.
d) Make the final connection to anunpainted, heavy metal part of theengine of the vehicle with the flatbattery.
WARNING
Never connect the jump lead directlyto the negative (-) terminal of thedischarged battery, or an explosionmay occur.
4) If the booster battery you are using is fittedto another vehicle, start the engine of the
vehicle with the booster battery. Run theengine at moderate speed.
5) Start the engine of the vehicle with theflat battery.
6) Remove the jump leads in the exactreverse order in which you connectedthem.
10-3 102
EMERGENCY SERVICE
TOWING EMERGENCY REMEDIES
If you need to have your vehicle towed, contacta professional service.
CAUTION
To help avoid damage to your vehicleduring towing, proper equipment andtowing procedures must be used.
Whenever possible, your vehicle should betowed from the front with the front wheels
lifted. If the steering and drivetrain are in goodcondition, your vehicle may be towed from therear with the rear wheels lifted and the frontwheels on the ground. Before towing, makesure the steering is unlocked and thetransmission is in neutral.
If the Starter Does Not Operate:1) Try turning the ignition switch to the
"START" position with the headlightsturned on to determine the batterycondition. If the headlights go excessivelydim or go off, it usually means that eitherthe battery is flat or the battery terminalcontact is poor. Recharge the battery orcorrect battery terminal contact asnecessary.
2) If the headlights remain bright, check thefuses. If the reason for failure of the starteris not obvious, there may be a majorelectrical problem. Have the vehicleinspected by your authorized MARUTIdealer.
103
If the vehicle runs out of fuel:If the vehicle runs out of fuel or work is carriedout on the fuel system, the fuel system mustbe primed as follows.
1) In case of running out of fuel, pour atleast5 litres into the tank with vehicle parkedon level ground.
2) Loosen the 1st priming nozzle shown inthe illustration.
3) Operate the bulb of the primer pumpslowly and steadily until air stops coming
out along with fuel from priming nozzle.4) Retighten the priming nozzle.
5) Loosen the 2nd priming nozzle shown inthe illustration.
10-4
EMERGENCY SERVICE
6) Operate the blub of the primer pump
slowly and steadily until air stops comingout along with fuel from priming nozzle.
7) Retighten the 2nd priming nozzle.
8) Operate the starter motor whilst slightlydepressing the accelerator pedal. If theengine fails to start at the first attempt,wait 15 seconds before trying again.
9) If the engine fails to start after severalattempts, prime the system again.
10) When the engine is idl ing, accelerateslightly to complete the bleeding of circuit.
If the Engine Overheats
The engine could overheat temporarily undersevere driving conditions. If the engine coolanttemperature gauge indicates overheatingduring driving:1) Turn off the air conditioner, if equipped.
2) Take the vehicle to a safe place and park.
3) Check the cooling fan is working and letthe engine run at normal idle speed for afew minutes until the indicator is withinthe normal, acceptable temperaturerange between "H" and "C .
WARNING
If you see or hear escaping steam, stop
the vehicle in a safe place andimmediately turn off the engine to letit cool. Do not open the bonnet whensteam is present. When the steam canno longer be seen or heard, open thehood to see if the coolant is stillboiling. If it is, you must wait until itstops boiling before you proceed.
If the temperature indication does not come
down to within the normal, acceptable range:
1) Turn off the engine and and wait until thecoolant temperature has lowered.
2) Check the coolant level in the reservoir. Ifit is found to be lower than the "LOW"mark, look for leaks at the radiator, aroundthe engine, and radiator and heater hoses.If you locate any leaks that may havecaused the overheating, do not run theengine until these problems have beencorrected.
WARNING
It is dangerous to remove the reservoircap when the water temperature ishigh, because scalding fljid and steammay be blown out under pressure.Thecap should only be taken off when thecoolant temperature has lowered.
WARNING
To help prevent personal injury, keephands, tools and clothing away fromthe engine cooling fan. Fan canautomatically turn on without warning.
10-5 104
EMERGENCY SERVICE
WARNING TRIANGLE
3) If you do not find a leak, carefully addcoolant to the reservoir. (Refer to "ENGINECOOLANT" in the "INSPECTION ANDMAINTENANCE" section.)
70F-08-002
In case of vehicle breakdown or during
emergency stopping where your vehicle
could become a potential traffic hazard,
keep the warning triangle, provided with
your vehicle, on the road free from any
obstacles behind your vehicle so as to warn
the approaching traffic, at an approximatedistance of 50-100 m, the reflecting side
of the triangle should face the on coming
traffic. Please activate the hazard warning
lamps before alighting the vehicle to keep
the warning triangle.
70F-08-003
Remove the warning trianglecarefully from the box as shown byarrow 1.
Open both the reflector arms as shownby arrows and lock arms with each other
with the clip provided in the right arm.Open the bottom stand in counter clock-wise direction as shown by arrow 3.Position the warning triangle behind thevehicle on a plain surface.
Reverse the removal procedure forkeeping inside the box.
105 10-6
EMERGENCY SERVICE
70F-08-004
10-7 106
WARNING