Z purlinZ purlin Our pre punched purlins are quick to install and suitable for both insulated and...
Transcript of Z purlinZ purlin Our pre punched purlins are quick to install and suitable for both insulated and...
Z purlinOur prepunched purlins are quick to install and suitable for both insulated and uninsulated roofs and walls.
The thickness and height of the purlin selected depend on span length and loads. To optimise the design, use ourPurCalc software.
Applications:
• Industrial construction
• Hall and warehouse construction
• Extension construction and renovation
The information on our web site is accurate to the best of our knowledge and understanding. Although every effort has been made to ensureaccuracy, the company cannot accept any responsibility for any direct or indirect damages resulting from possible errors or incorrect
application of the information of this publication. We reserve the right to make changes.
Copyright © 2015 SSAB or its affiliates. All Rights Reserved.
Document printed on 14.10.2015 www.ruukki.com
Properties
Section type: Zsections
Height: 100, 120, 150, 200, 250, 300, 350 mm
Thickness: 1.0–3.0 mmMinimum length 1600 mmMaximum length 18500 mm
Material: Hot galvanised steel sheetSteel quality S350GD+Z275 according to EN10346
Tolerances: Roll formed products EN 10162Pressbraked products EN 10162 and EN10902Material EN 10143
Dimensioning: It is advisable to use PurCalc software whendimensioning lightweight purlins. Dimensioningcurves are also available.
Z purlin
2
Lightweight purlins Z – crosssection geometries
Z PurlinTypeofpurlin
Thickness stripwidth
Height Widthofwide flange
Widthofnarrowflange
Fold Weight Crosssectionarea,gross
CrosssectionCrosssection area,effective *
Bressbrake
Rollformed
Max / Minlength
Steelgrade
tnom W H A B C g Agross Aeff
mm mm mm mm mm mm kg/m cm2 cm2
LPZ100
1 207 100 45 39 >=15.50 1.63 199.4 120.6 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
1.2 45.4 39.4 >=15.90 1.96 240.8 167.7 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
1.5 46 40 >=16.50 2.45 302.8 236.2 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
LPZ120
1 230(228)
120 45 39 >=16.00 1.81 219.6 120.8 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
1.2 45.4 39.4 >=16.40 2.17 265.2 168.8 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
1.5 46 40 >=17.00 2.71 333.4 238.6 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
2 47 41 >=18.00 3.61 447 363.2 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
LPZ150
1 260(258)
150 45 39 >=16.00 2.04 248.4 120 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
1.2 45.4 39.4 >=16.40 2.45 300 167.6 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
1.5 46 40 >=17.00 3.06 377.2 238.3 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
2 47 41 >=18.00 4.08 505.8 366.1 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
LPZ200
1.5 370(368)
200 70 62 >=24.00 4.36 549.5 277.8 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
2 71 63 >=25.00 5.81 737 467.7 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
2.5 72 64 >=26.00 7.26 924.2 655.9 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
3 73 65 >=27.00 8.71 1111 855.7 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
LPZ250
1.5 420(418)
250 70 62 >=24.00 4.92 622.5 275.7 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
2 71 63 >=25.00 6.56 835 464.1 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
2.5 72 64 >=26.00 8.2 1047.2 655.2 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
3 73 65 >=27.00 9.84 1259 859.8 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
LPZ300
1.5 505 300 89 81 >=22.50 5.95 746.6 259.5 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
2 90 82 >=23.50 7.93 1001.6 449.2 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
2.5 91 83 >=24.50 9.91 1256.3 674.5 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
3 92 84 >=25.50 11.89 1510.6 905.9 l 1600mm/18000mm
PlaingalvanizedS350GD+Z275
* Cross section is fully compressed
Z purlin
3
Services
Purlins can be prepunched in our factory. This makes construction onsite faster and easier. The standardised sizes andlocations of holes for fixing screws are presented below. Please contact us for additional information about the prepunchingpossibilities.
Holes are made during production at continuous line – information:
• max. material thickness 3mm (for ø 60mm max. material thickness 2mm),
• holes can be made in a row,
• oval and rectangular holes can be rotated by 90°.
Type of hole Diameter (mm) Rotation (°)
7
10
12
14
16
18
20
22
26
60
12×24 90
14×24 90
16×35 90
18×31.7 90
18×35 90
20×35 90
5×25 90
Design tools
Our PurCalc software is constantly improved and updated to easily design and optimise Ruukki’s lightweight purlinsections.
Choosing the right filters will help you to select the right product characteristics. The software enables the calculation ofvarious roof purlin systems, whether the purlins are restrained by trapezoidal sheeting or roof sandwich panels. DownloadPurCalc
Order & delivery
Use Ruukki's optimisation software PurCalc to design the purlin structure.
Please provide the following information in the order:
• Type of purlin
• Thickness
Z purlin
4
• Length
• Number
In case of prepunched purlins, please send us purlin drawings showing the location of the holes.
Note! Our standard raw material for purlins is S350GD+Z275.
Declaration of Performance
The content of this document has been created from web page last updated 28 Sep 2015Our sales and technical support are happy to give you more information. Visit www.ruukki.com/contactus.
Z purlin
5