YB4400 Series - Maxim Crane Works...pivoted fully forward. Boom Elevation Single double acting...
Transcript of YB4400 Series - Maxim Crane Works...pivoted fully forward. Boom Elevation Single double acting...
productguide
features
• 4 models …
YB4409: 8.5T (7.7mt) 3-section boom with25 ft. 2 in. (7.6m) Tip Height
YB4409XL: 8.5T (7.7mt) 3-section boomwith 33 ft. 6 in. (10.2m) Tip Height
YB4409-2: 9.0T (8.1mt) 3-section boomwith 38 ft. 2 in. (11.6m) Tip Height
YB4411: 10.5T (9.5mt) 3-section boomwith 38 ft. 2 in. (11.6m) Tip Height
• 6 ft. (1.8m) fixed extension (YB4409 / XL)and 12 ft. (3.6m) offsettable swingawayextension (YB4409-2 & YB4411)
• 70 bhp (52.2 kW)GM EFI dualfuel engineor 99 bhp(73.8 kW)Cumminsdieselengine
YB4400 Series
Industrial Hydraulic Crane
contentsFeatures 2Specifications 3YB4409
Dimensions 5Range Diagram 6Load Chart 7
YB4409XL
Dimensions 8Range Diagram 9Load Chart 10
YB4409-2
Dimensions 11Range Diagram 12Load Chart 13
YB4411
Dimensions 14Range Diagram 15Load Chart 16
YB4409 (metric)
Range Diagram 17DIN/ISO Load Chart 18
YB4409XL (metric)
Range Diagram 19DIN/ISO Load Chart 20
YB4409-2 (metric)
Range Diagram 21DIN/ISO Load Chart 22
YB4411 (metric)
Range Diagram 23DIN/ISO Load Chart 24
www.manitowoccranegroup.com*Product may be shown with optional equipment.
features
2
Standard: 21 ft. (6.4m) main boom on the YB440930 ft. (9.1m) main boom on the YB4409XL32 ft. 10 in. (10.0m) main boom on the YB4409-2& YB4411
Optional: Manual 4th main boom section adds 10 ft. (3.0m)additional main boom length on YB4409 andYB4409-XL only.
Standard: 4-wheel coordinated steerOptional: 2-wheel, 4-wheel, and crab steer
(std. on YB4409-2)Standard: 2-wheel, 4-wheel, and crab steer with
self alignment (YB4411)
Standard: Open air cab shell w/overhead safetyglass
Optional: Closed cab with hinged door, heater,and defroster
Standard: Cummins QSB 3.3L turbo-charged diesel rated @ 99bhp (73.8kW) @ 2600 rpm.
• Singlepositionoblique styleoutriggers
• Narrow widthfor insideaisle wayusage
3
YB4400
Seri
es
specifications
Superstructure
BoomYB4409: 9 ft. 8 in. – 21 ft. 2 in. (2.9m – 6.5m) three- section fullpower boom.Maximum tip height: 25 ft. 2 in. (7.6m)
YB4409XL: 12 ft. 8 in. – 30 ft. 2 in. (3.8m – 9.2m) three- sectionfull power boom.Maximum tip height: 33 ft. 6 in. (10.2m)
YB4409-2 & YB4411: 13 ft. 10 in. – 32 ft. 10 in. (4.2m – 10.0m)three-section full power boom.Maximum tip height: 38 ft. 2 in. (11.6m)
*Optional BoomYB4409 & YB4409XL: Manual 4th main boom fly section
*Boom ExtensionYB4409 & YB4409XL: 6 ft. (1.8m) fixed pin on extensionYB4409-2 & YB4411: 12 ft. (3.6m) offsettable extension
12-18 ft. (3.6-5.4m) telescopic offsettable extension
Boom NoseYB4409 / XL: Single sheave non-pivoting YB4409-2 & YB4411 only: Single sheave, 3-position (0˚, + 30˚, +80˚) pivoting boom nose for minimizing head spacerequirements. Lowers head height 10.5 in. (0.26m) when nose ispivoted fully forward.
Boom ElevationSingle double acting hydraulic cylinder with integral holdingvalve.Elevation: 0° to 60° for the YB4409 & YB4409XL
0° to 72° for the YB4409-2 & YB4411
Anti-Two Block DeviceStandard anti-two block device, when activated, provides anaudible warning to the crane operator and disengages all cranefunctions whose movement can cause two-blocking.
Load Indicator A simple, effective, and easy to use load indicating system
used in conjunction with the anti-two block system to assist theoperator in efficient operation of the unit within the limits of theload chart. The display panel displays the hook load and warnsthe operator when a preset load capacity is exceeded. Thewarning is by a flashing light on the display panel. Inconjunction with the load display panel (receiver), there is awireless transmitter and load sensing pin attached to the boomhead that transmits the hook load to the display panel.
*Rated Capacity Limiter (RCL)Similar to the Load Indicator, but stops the telescope out
and boom lift down function when a load limit is exceeded.Uses a similar display panel with the addition of displaying boomangle and boom length read outs on the panel.
*Load Moment Indicator (LMI)Digital display of boom angle, boom length, boom radius,capacity, and allows for operator in-put to set the limits based onload chart. Displays color coded light bar and audible alarmwith function cutout if load exceeds entered parameters.
Swing Ball bearing swing circle with 360° continuous rotation. Hydraulic driven worm gear and pinion.Maximum speed: 2.05 rpm
Hydraulic SystemYB4409 & 4409XL: (2) gear pumps
YB4409-2 & YB4411: Variable displacement piston pump andpiggyback gear pump.
Combined flow: 28.5gpm (107.9Lpm)
Maximum system operating pressure: 3600 psi
YB4409 & YB4409XL: Six section valve bank mounted in dashpanel with direct mechanical linkage for low effort lever control.
YB4409-2 & YB4411: Six section valve bank chassis mounted;operated via dash mounted, pilot pressure hydraulic joysticks.
Return line filter with full flow by-pass protection and serviceindicator.
23.5 gallon (89 L) hydraulic reservoir with sight level gauge andsteel side plating to guard against side impact damage.
Hoist Specifications
YB4409 / XL: Worm drive with counter-balance valving. Equalspeed power up and down.
YB4409-2 & YB4411: Piston motor drive w/springapplied/hydraulic released brake.
Drum Diameter:YB4409 / XL: 9.69 in. (0.24m)YB4409-2 & YB4411: 10.63 in. (0.27m)
Maximum Single Line Pull: YB4409 / XL: 10,700lb (4 854kg)YB4409-2 & YB4411: 14,000lb (6 350 kg)
Maximum Single Line Speed:YB4409 / XL: 88 FPM (26.8m / min)YB4409-2 & YB4411: 120FPM (36.6m / min)
Maximum Permissible Single Line Pull:YB4409 / XL : 8,500lb (3 855 kg)(1/2” [12.7mm] Python Ultra XIPS) YB4409-2 & YB4411: 10,000lb (4 536kg)(9/16” [14.0mm] EEIPS)
Rope Length :YB4409 / XL: (3-section boom) 97 ft. (29.6m)
(4-section boom) 130 ft. (39.6m)YB4409-2 & YB4411: 120 ft. (36.6m)
*Denotes optional equipment
Boom
Boom
Boom Extension
Boom Nose
Boom Elevation
Load Moment & Anti-Two Block System
Load Moment & Anti-Two Block System
Load Moment & Anti-Two Block System
Load Moment & Anti-Two Block System
Swing
Hydraulic System
Hoist
4
YB4400
Seri
es
specifications
Carrier
FrameHigh strength alloy steel constructed with integral outriggerhousings; front and rear lifting, towing, and tie-down lugs. 42 ft.2
carrydeck size with 14,000 lb (6 350kg) carrying capacity(YB4409 / XL / YB4409-2) and 17,000 lb (7 711kg) carryingcapacity (YB4411). Deck coated with anti-skid treatment.
OutriggersYB4409, YB4409XL & YB4409-2: Front and rear oblique typebeams at all four corners with integral holding valves. Outriggerpads form an integral part of the beam.YB4411: Hydraulic telescoping beam with oblique type jackprovides extended and down and retracted and down liftingcapacities. Integral holding valves on both beam and jack.
Outrigger ControlsYB4409-2, YB4409 & YB4409XL: Lever controls located on dashpanel which operate the beams in pairs from side to side.YB4411: Two switch operation mounted on dash panel. One -3-position rocker switch to select all beams / jacks, left beams /jacks only, or right beams / jacks only. Separate -4- way toggleswitch to activate beams out / in and jacks down / up. Levelbubble indicator located inside operators compartment.*Independent outrigger controls available as an option.
Std. Engine (Tier III)Cummins QSB 3.3L turbo-charged diesel rated @ 99 bhp(73.8kW) @ 2600 rpm.
*Optional EngineG.M. 3.0L EFI dual fuel (gasoline / L.P.) rated @ 70 bhp (52.2kW)@ 2600 rpm.
Operators Control StationFrame mounted, open air style control station with cab shell.Includes all crane functions, driving controls, and overheadsafety glass. Other standard equipment include a durableweather resistant seat with seat belt, hourmeter, sight levelbubble, and fire extinguisher. The dash panel includes engineoil pressure gauge, engine water temperature gauge, fuelgauge, transmission low oil and high temperature warning lights,low battery warning light, and brake system low pressurewarning light. The LSI (load indicator) receiver is mounted to thetop of the dash and provides warning for A2B and exceededload capacity.
*Operators Control Station EnclosedIncludes the standard cab shell with the addition of front andrear glass and sliding glass on the right side. Hinged full doorwith sliding glass.
Front windshield wiper and heater and defroster is included.
Fuel Tank Capacity18.5 gallon (70 L) all steel construction with steel side plate toguard against side impact.
Electrical SystemOne 12V maintenance free battery, 820CCA @ 0°. Jump start connections63 amp alternator.
Drive4 x 2 – Front axle drive with planetary hubs and limited slip Differential.
SteerYB4409 / XL: 2-wheel, 4-wheel steerYB4409-2: 2-wheel, 4-wheel w/crab steerYB4411: 2-wheel, 4-wheel, and crab steer w/ electronic self
alignment.
TransmissionYB4409 / XL & YB4409-2: Clark synchromesh -4- speeds
forward and reverse with stalk mountedforward/reverse selector.
YB4411 : Clark powershift -4- speeds forward and reverse.Stalk mounted shifter on left side of steeringcolumn.
AxlesFront: Carraro planetary drive/steer with internal multi-wet-discbrakes and limited slip differential.Rear: Fabricated non-drive steer with disc brakes
Tires10.00 x 15 14PR pneumatic
BrakesHydraulic actuated internal wet-disc service brakes acting on allfour wheels. A dash mounted toggle switch activates the drydisc parking brake on the transmission output yoke with a dashwarning light.
SuspensionFront: Rigid mounted to frame.Rear: Rigid mounted to frame
LightsRecessed mounted, includes head, tail, rear work, stop, and turnsignals.
Maximum Speed22 MPH (35.6km/h)
Gradeability**YB4409 / XL & YB4409-2: 57%....no load
31%....12,000lb (5 443kg) load
YB4411: 68%....no load40%....20,000lb (9 072kg) load
G.V.W.YB4409: 13,400 lb. (6 078 kg)YB4409XL: 15,180 lb (6 885 kg)YB4409-2: 15,800 lb (7 167 kg)YB4411: 16,600 lb (7 530 kg)
Miscellaneous Standard EquipmentSingle sheave, “Quick Reeve” style hookblock.; YB4409 / XL 8.5T (8.0mt); YB4409-2: 9T (8.1mt); YB4411 10.5T(10mt).Back-up alarm.
*Denotes optional equipment**Theoretical
Frame
Outriggers
Outrigger Controls
Engine
Engine
Cab
Cab
Fuel Tank Capacity
Electrical System
Drive
Steering
Transmission
Axles
Tires
Brakes
Suspension
Lights
Speed
Grade
5
YB4400
Seri
es
dimensions
1' 0"(0.30 m)
5' 11.88"(1.33 m)
3' 7.75"(1.1 1 m)
3' 3"(0.99 m)
4' 2.88"(1.88 m)
1' 11.5"(0.60 m)
3.12"(0.08 m)
3' 3.5"(1.0 m)
1' 6"(0.46 m)
3' 4.5"(1.00 m)
5' 7"(1.70 m)
5' 8.38"(1.74 m)
5' 8.38"(1.74 m)
5' 11.88"(1.82 m)
11' 11.75"(3.65 m)
12' 7"(3.84 m)
1' 0"(0.30 m)
6' 7.5"(2.01 m)
9.5" (On T ires)(0.25 m)
3' 6"(1.07 m)
3' 2"(0.97 m)
7' 10"(2.39 m)
5' 9.7"(1.77 m)
5' 3"1.60 m)
6' 4"(1.93 m)
6' 6.25"(1.99 m)
9' 2.75"(2.81 m)
10' 2"(3.10 m)
YB4409 Dimensions
1' 0"(0.30 m)
5' 11.88"(1.33 m)
3' 7.75"(1.1 1 m)
3' 3"(0.99 m)
4' 2.88"(1.88 m)
1' 11.5"(0.60 m)
3.12"(0.08 m)
3' 3.5"(1.0 m)
1' 6"(0.46 m)
3' 4.5"(1.00 m)
5' 7"(1.70 m)
5' 8.38"(1.74 m)
5' 8.38"(1.74 m)
5' 11.88"(1.82 m)
11' 11.75"(3.65 m)
12' 7"(3.84 m)
1' 0"(0.30 m)
6' 7.5"(2.01 m)
9.5" (On T ires)(0.25 m)
3' 6"(1.07 m)
3' 2"(0.97 m)
7' 10"(2.39 m)
5' 9.7"(1.77 m)
5' 3"1.60 m)
6' 4"(1.93 m)
6' 6.25"(1.99 m)
9' 2.75"(2.81 m)
10' 2"(3.10 m)
YB4409 DimensionsYB4409
6
YB4400
Seri
es
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
35
5
10
0
5
10
15
20
25
3S
EC
TIO
N
4S
EC
TIO
N
50 1510 2520 30
30
35
40
45°
30°
60°
0°
15°
10 5 0 5 10 15 20 25 30 35
10
0
5
15
20
30
25
35
40
6'JI
B
YB4409H
EIG
HT
FR
OM
GR
OU
ND
INF
EE
T
OPERATING RADIUS IN FEET FROM AXIS OF ROTATION
range diagram
7
YB4400
Seri
es
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
ON RUBBER (lbs)ON OUTRIGGERS (lbs)
MA
INB
OO
MJI
B
170005.0
RADIUS(ft)
6.0 157008.0 12400
10.0 1020012.0 850014.0 720016.018.020.022.024.526.028.030.031.0
17000144001080086007000
2600
--
-2200
35502700
43005400
- -
2200
--
500027002600
6100
-
1000010000
100007450
2175
825
---
675-
1100950
13251700
44002950
3400
1350
-
--
1150-
17751525
21502650
71504700
F/R 360° F/R 360°
3-SECTION BOOM OR4-SECTION BOOM WITH 4TH RETRACTED
ON RUBBER (lbs)ON OUTRIGGERS (lbs)
61005.0
RADIUS(ft)
6.0 61008.0 5300
10.0 470012.0 440014.0 440016.018.020.022.024.526.028.030.031.0
61006100530047004400
2700
19001700
21252300
41003150
44004400
2200 1625
3100
25002700
440043003700
4400
2300
61006100
61006100
2450
850
575475425
700650
12251000
15251875
52503750
3800
1375
975
800850
12001100
19001600
23252900
53004700
F/R 360° F/R 360°
4-SECTION BOOM WITH 4TH EXTENDED
***
**
10
4-SECTION BOOM
2875
2400
2200
28002700
3500
31503000
4-SECTION BOOM
3325
26002500
22502325
3-SECTION BOOM OR
WITH 4TH RETRACTED WITH 4TH EXTENDED
2875
2400
2200
28002700
3500
31503000
3325
26002500
22502325
BOOM
(deg)ANGLE
MAIN
60
40
15
0
3035
455055
2520
5
0-17000lbs2-PART
0-8500lbs1-PART
RIGGING CHART
FRONT REAR
SIDE
WIRE ROPE: 1/2 inch diameter
Min. breaking strength 29750 lbs.
SIDE
REDUCTION CHART
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
140 lbs
100 lbs
0 lbs
150 lbs
N/A
100 lbs
N/A
0 lbs
15°
30°
15°
30°
The rated loads are the maximum lift
capacities as determined by operating
radius, boom extension and boom
angle. The operating radius is the
horizontal distance from a projection
of the axis of rotation to the
supporting surface, before loading, to
the center of vertical hoist line or
tackle with load applied.
The rated loads shown on outriggers
do not exceed 85% of actual tipping.
The rated loads shown on rubber do
not exceed 75% of actual tipping.
These ratings are based on freely
suspended loads with the crane
leveled, standing on a firm, uniform
supporting surface. Practical working
loads depend on supporting surface,
operating radius and other factors
affecting stability. Hazardous
surroundings, climatic conditions,
experience of personnel and proper
training must all be taken into account
by the operator.
The weights of all load handling
devices such as hooks, hook blocks,
slings, etc., except the hoist rope,
shall be considered as part of the
load. See reduction chart.
Ratings on outrigggers are for either
outriggers fully extended and down or
fully retracted and down. Ratings for
outriggers fully retracted and down
will apply for any intermediate
outrigger setting.
Ratings on rubber depend on tire
capacity, condition of tires and proper
inflation pressure (100 psi). Loads on
rubber may be transported at a
maximum speed of 2.5 mph on a
smooth hard level surface with boom
retracted to the shortest length
possible and centered over front.
For operating radius not shown, use
load rating of next larger radius.
The maximum combined total boom
and deck load is 12000 lbs. The
maximum deck load only is 14000 bs.
Do not induce any external side loads
to boom or jib.
1) 5)
6)
7)
8)
2)
3)
4)
JIB STRUCTURAL CAPACITIES (lbs.)
*LIMIT RATINGS TO 11,800 LBS WHEN 3RD SECTION IS EXTENDED ANY AMOUNT.
JIB CAPACITY IS LIMITED BY BOTH STRUCTURALCAPACITY CHART AND MAIN CAPACITY CHART.
SHADED AREAS ARE GOVERNED BY STRUCTURALSTRENGTH, DO NOT RELY ON TIPPING.
YB4409
load chart
8
YB4400
Seri
es
dimensions
1' 0"(0.30 m)
5' 11.88"(1.33 m)
4' 9.13"(1.45 m)
2' 11.75"(0.91 m)
4' 2.88"(1.88 m)
1' 11.5"(0.60 m)
3.12"(0.08 m)
3' 3.5"(1.0 m)
1' 6"(0.46 m)
3' 4.5"(1.00 m)
5' 7"(1.70 m)
5' 8.38"(1.74 m)
5' 8.38"(1.74 m)
5' 11.88"(1.82 m)
11' 11.75"(3.65 m)
15' 7"(4.75 m)
1' 0"(0.30 m)
9' 7.5"(2.93 m)
9.5" (On Tires)(0.25 m)
3' 6"(1.07")
3' 2"(0.97 m)
7' 10"(2.39 m)
5' 9.7"(1.77 m)
5' 3"1.60 m)
6' 4"(1.93 m)
6' 6.25"(1.99 m)
9' 2.75"(2.81 m)
10' 2"(3.10 m)
YB4409XL Dimensions
1' 0"(0.30 m)
5' 11.88"(1.33 m)
4' 9.13"(1.45 m)
2' 11.75"(0.91 m)
4' 2.88"(1.88 m)
1' 11.5"(0.60 m)
3.12"(0.08 m)
3' 3.5"(1.0 m)
1' 6"(0.46 m)
3' 4.5"(1.00 m)
5' 7"(1.70 m)
5' 8.38"(1.74 m)
5' 8.38"(1.74 m)
5' 11.88"(1.82 m)
11' 11.75"(3.65 m)
15' 7"(4.75 m)
1' 0"(0.30 m)
9' 7.5"(2.93 m)
9.5" (On Tires)(0.25 m)
3' 6"(1.07")
3' 2"(0.97 m)
7' 10"(2.39 m)
5' 9.7"(1.77 m)
5' 3"1.60 m)
6' 4"(1.93 m)
6' 6.25"(1.99 m)
9' 2.75"(2.81 m)
10' 2"(3.10 m)
YB4409XL DimensionsYB4409XL
9
YB4400
Seri
es
YB4409XL
355
NOITCES
3
NOITCES
4
50 1510 2520 30
45°
30°
60°
40
0°
15 °
5 0 5 10 15 20 25 30 35 40
10
0
5
15
20
30
25
35
40
45
45
45
BIJ'6
50
5
100
10
15
20
25
30
35
40
45
10
50
OPERATING RADIUS IN FEET FROM AXIS OF ROTATION
HEIG
HTFR
OMGR
OUND
INFE
ET
range diagram
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
10
YB4400
Seri
es
load chart
YB4409XL
8. Do not induce external side loads to boom or jib.
is 14,000 lbs with 10:00 x 15 tires. Tire inflation at
12,000 lbs. For deck loads only, the maximum load
7. The maximum combined total boom and deck load is
next larger radius.
6. For operating radius not shown, use load rating of the
on a smooth hard level surface with boom retracted
may be transported at a maximum speed of 2.5 mph
tires, and proper inflation pressure (100 psi). Loads on rubber
5. Ratings on rubber depend on tire capacity, condition of
4. Ratings on outriggers are with outriggers fully extended.
be considered as part of the load. See reductrion chart.
hook blocks, slings, etc., except the hoist rope, shall
3. The weights of all load handling devices, such as hooks,
proper handling must all be taken into account by the
Hazardous surroundings, experience of personnel and
Practical working loads depend on supporting surface,
leveled, standing on a firm, uniform supporting surface.
based on freely suspended loads with the machine
not exceed 75% of actual tipping. These ratings are
of actual tipping. The rated loads shown on rubber do
2. The rated loads shown on outriggers do not exceed 85%
the supporting surface, before loading, to the center
distance from a projection of the axis of rotation to
operating radius. The operating radius is the horizontal
of boom lengths and angles may be used to obtain
determined by operating radius only. Any combination
of vertical hoist line or tackle with load applied.
operating radius, and other factors affecting stability.
operator.
to the shortest length possible and centered over front.
at 100 psi.
RELY ON TIPPING.
DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
30°
15° 15°
30°
FRONT REAR
SIDE
SIDE
3-SECTION BOOM OR 4-SECTION BOOM WITH 4TH RETRACTED
RADIUS
OPERATING
0-17000lbs
2-PART
0-8500lbs
1-PART
RIGGING CHART
950 lbs
1100 lbs
1300 lbs
1500 lbs
1800 lbs
2150 lbs
2750 lbs
3800 lbs
5400 lbs
8000 lbs
32.0 ft
30.0 ft
28.0 ft
26.0 ft
24.0 ft
22.0 ft
20.0 ft
18.0 ft
16.0 ft
14.0 ft
12.0 ft
10.0 ft
8.0 ft
6.0 ft
5.0 ft
2900 lbs
3300 lbs
3800 lbs
4450 lbs
33.5 ft
1450 lbs
1150 lbs
950 lbs
800 lbs
650 lbs
550 lbs
5600 lbs
3800 lbs
2700 lbs
1950 lbs
4650 lbs
2050 lbs
2350 lbs
2700 lbs
3150 lbs
3800 lbs
4-SECTION BOOM WITH 4TH EXTENDED
ON RUBBER
28.0 ft
33.5 ft
36.0 ft
30.0 ft
32.0 ft
5.0 ft
16.0 ft
22.0 ft
24.0 ft
26.0 ft
18.0 ft
20.0 ft
10.0 ft
12.0 ft
14.0 ft
6.0 ft
8.0 ft
FRONT
ON OUTRIGGERS
360°
950 lbs
800 lbs
700 lbs
625 lbs
550 lbs
600 lbs
500 lbs
400 lbs
325 lbs
250 lbs
2000 lbs
1800 lbs
1600 lbs
1400 lbs
1250 lbs
2750 lbs
2450 lbs
2200 lbs
1950 lbs
1750 lbs
WIRE ROPE: 1/2 inch diameter
Min. breaking strength 29750 lbs.
27.0 ft 850 lbs 500 lbs 2750 lbs 1900 lbs 27.0 ft
SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND
42.0 ft
40.0 ft
38.0 ft
43.0 ft
475 lbs
325 lbs
350 lbs
400 lbs
125 lbs
150 lbs
200 lbs
225 lbs
1300 lbs
1350 lbs
1475 lbs
1625 lbs
875 lbs
925 lbs
1025 lbs
1125 lbs
525 lbs
600 lbs
700 lbs
800 lbs
275 lbs
325 lbs
400 lbs
475 lbs
1875 lbs
2025 lbs
2275 lbs
2525 lbs
1300 lbs
1425 lbs
1600 lbs
1775 lbs
REDUCTION CHART
FRONT 360°
ON RUBBER
FRONT
ON OUTRIGGERS
360° FRONT 360°
RADIUS
OPERATING
MO
OB
NIA
MB I
J
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
140 lbs
100 lbs
0 lbs
150 lbs
N/A
100 lbs
N/A
0 lbs
JIB STRUCTURAL CAPACITIES @ MAIN BOOM ANGLE (ALSO DO NOT EXCEED CAPACITIES IN ABOVE CHART)
0° 15° 30° 45° 60°
JIB STRUCTURAL CAPACITIES @ MAIN BOOM ANGLE (ALSO DO NOT EXCEED CAPACITIES IN ABOVE CHART)
0° 15° 30° 45° 60°
42.0 ft
40.0 ft
38.0 ft
43.0 ft
36.0 ft -- -
- --
-
-
-- -
- --
-
-
- -- -
6000 lbs7100 lbs 8500 lbs 10200 lbs 12400 lbs15700 lbs 17000 lbs
5200 lbs
17000 lbs
5800 lbs 6950 lbs 8500 lbs 10800 lbs14400 lbs 9500 lbs
10000 lbs 8200 lbs
10000 lbs
2900 lbs
1100 lbs
1350 lbs
1600 lbs
1950 lbs
2400 lbs
2100 lbs
700 lbs
850 lbs
1050 lbs
1350 lbs
1700 lbs
2600 lbs
3300 lbs
4250 lbs
2300 lbs
2650 lbs
-- -
- --
-
-
1000 lbs 650 lbs2900 lbs 2150 lbs
3100 lbs
2900 lbs 2900 lbs 2900 lbs 2900 lbs 2900 lbs
3400 lbs 3800 lbs 4300 lbs 4900 lbs
3400 lbs 3100 lbs
2900 lbs 2900 lbs 2900 lbs
3800 lbs
4900 lbs 4300 lbs
3400 lbs 3800 lbs 4300 lbs 4900 lbs 4900 lbs
2000 lbs 2100 lbs 2200 lbs 2600 lbs 3400 lbs 2200 lbs 2400 lbs 2700 lbs 3000 lbs 3500 lbs
1. The rated loads are the maximum lifting capacities as
al side loads to boom or jib.
0 x 15 tires. Tire inflation at
oads only, the maximum load
ned total boom and deck load is
not shown, use load rating of the
l surface with boom retracted
a maximum speed of 2.5 mph
on pressure (100 psi). Loads on rubber
5 pend on tire capacity, condition of
are with outriggers fully extended.
of the load. See reductrion chart.
c., except the hoist rope, shall
3 d handling devices, such as hooks,
all be taken into account by the
gs, experience of personnel and
s depend on supporting surface,
firm, uniform supporting surface.
nded loads with the machine
ual tipping. These ratings are
ated loads shown on rubber do
2 n on outriggers do not exceed 85%
, before loading, to the center
tion of the axis of rotation to
operating radius is the horizontal
ngles may be used to obtain
ng radius only. Any combination
tackle with load applied.
other factors affecting stability.
possible and centered over front.
RELY ON TIPPING.
DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
30°
15° 15°
30°
FRONT REAR
SIDE
SIDE
3-SECTION BOOM OR 4-SECTION BOOM WITH 4TH RETRACTED
0-17000lbs
2-PART
0-8500lbs
1-PART
RIGGING CHART
950 lbs
1100 lbs
1300 lbs
1500 lbs
1800 lbs
2150 lbs
2750 lbs
3800 lbs
5400 lbs
8000 lbs
3
0 lbs
0 lbs
0 lbs
0 lbs
3
1450 lbs
1150 lbs
950 lbs
800 lbs
650 lbs
550 lbs
5600 lbs
3800 lbs
2700 lbs
1950 lbs
4650 lbs
2050 lbs
2350 lbs
2700 lbs
3150 lbs
3800 lbs
4-SECTION BOOM WITH 4TH EXTENDED
ON RUBBER
28.0 ft
33.5 ft
36.0 ft
30.0 ft
32.0 ft
5.0 ft
16.0 ft
22.0 ft
24.0 ft
26.0 ft
18.0 ft
20.0 ft
10.0 ft
12.0 ft
14.0 ft
6.0 ft
8.0 ft
FRONT
ON OUTRIGGERS
360°
950 lbs
800 lbs
700 lbs
625 lbs
550 lbs
600 lbs
500 lbs
400 lbs
325 lbs
250 lbs
2000 lbs
1800 lbs
1600 lbs
1400 lbs
1250 lbs
2750 lbs
2450 lbs
2200 lbs
1950 lbs
1750 lbs
WIRE ROPE: 1/2 inch diameter
Min. breaking strength 29750 lbs.
2 850 lbs 500 lbs0 lbs 1900 lbs 27.0 ft
SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND
42.0 ft
40.0 ft
38.0 ft
43.0 ft
475 lbs
325 lbs
350 lbs
400 lbs
125 lbs
150 lbs
200 lbs
225 lbs
1300 lbs
1350 lbs
1475 lbs
1625 lbs
875 lbs
925 lbs
1025 lbs
1125 lbs
525 lbs
600 lbs
700 lbs
800 lbs
275 lbs
325 lbs
400 lbs
475 lbs
5 lbs
5 lbs
5 lbs
5 lbs
1300 lbs
1425 lbs
1600 lbs
1775 lbs
REDUCTION CHART
FRONT 360°
ON RUBBER
RONT
ON OUTRIGGERS
360° FRONT 360°
RADIUS
OPERATING
MO
OB
NIA
MB I
J
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
140 lbs
100 lbs
0 lbs
150 lbs
N/A
100 lbs
N/A
0 lbs
J PACITIES @ MAIN BOOM ANGLE (ALSO DO NOT EXCEED CAPACITIES IN ABOVE CHART)
15° 30° 45° 60°
JIB STRUCTURAL CAPACITIES @ MAIN BOOM ANGLE (ALSO DO NOT EXCEED CAPACITIES IN ABOVE CHART)
0° 15° 30° 45° 60°
- -
- -
-
-
- -
- -
-
-
- --
0 lbs7 lbs 0 lbs
0 lbs 1 0 lbs1 0 lbs 1 0 lbs
0 lbs
17000 lbs
5800 lbs 6950 lbs 8500 lbs 10800 lbs14400 lbs 9500 lbs
10000 lbs 8200 lbs
10000 lbs
2900 lbs
1100 lbs
1350 lbs
1600 lbs
1950 lbs
2400 lbs
2100 lbs
700 lbs
850 lbs
1050 lbs
1350 lbs
1700 lbs
2600 lbs
3300 lbs
4250 lbs
2300 lbs
2650 lbs
-- -
- --
-
-
1000 lbs 650 lbs 2900 lbs 2150 lbs
3100 lbs
2900 lbs 2900 lbs 2900 lbs 2900 lbs 2900 lbs
3400 lbs 3800 lbs 4300 lbs 4900 lbs
3400 lbs 3100 lbs
2900 lbs 2900 lbs 2900 lbs
3800 lbs
4900 lbs 4300 lbs
3400 lbs 3800 lbs 4300 lbs 4900 lbs 4900 lbs
2000 lbs 2100 lbs 2200 lbs 2600 lbs 3400 lbs 2 2400 lbs 2700 lbs 3000 lbs 3500 lbs
e maximum lifting capacities as
ANTY.
30°
15° 15°
30°
FRONT REAR
SIDE
SIDE
0-17000lbs
2-PART
0-8500lbs
1-PART
RIGGING CHART
4-SECTION BOOM WITH 4TH EXTENDED
ON RUBBER
FRONT
ON OUTRIGGERS
360°
950 lbs
800 lbs
700 lbs
625 lbs
550 lbs
600 lbs
500 lbs
400 lbs
325 lbs
250 lbs
2000 lbs
1800 lbs
1600 lbs
1400 lbs
1250 lbs
2750 lbs
2450 lbs
2200 lbs
1950 lbs
1750 lbs
WIRE ROPE: 1/2 inch diameter
Min. breaking strength 29750 lbs.
NOT
AND
475 lbs
325 lbs
350 lbs
400 lbs
125 lbs
150 lbs
200 lbs
225 lbs
1300 lbs
1350 lbs
1475 lbs
1625 lbs
875 lbs
925 lbs
1025 lbs
1125 lbs
REDUCTION CHART
FRONT 360°
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
140 lbs
100 lbs
0 lbs
150 lbs
N/A
100 lbs
N/A
0 lbs
J RAL CAPACITIES @ MAIN BOOM ANGLE (ALSO DO NOT EXCEED CAPACITIES IN ABOVE CHART)
15° 30° 45° 60°
2900 lbs
1100 lbs
1350 lbs
1600 lbs
1950 lbs
2400 lbs
2100 lbs
700 lbs
850 lbs
1050 lbs
1350 lbs
1700 lbs
2600 lbs
3300 lbs
4250 lbs
2300 lbs
2650 lbs
-- -
- --
-
-
1000 lbs 650 lbs 2900 lbs 2150 lbs
3100 lbs
2900 lbs 2900 lbs 2900 lbs 2900 lbs 2900 lbs
3400 lbs 3800 lbs 4300 lbs 4900 lbs
3400 lbs 3100 lbs
2900 lbs 2900 lbs 2900 lbs
3800 lbs
4900 lbs 4300 lbs
3400 lbs 3800 lbs 4300 lbs 4900 lbs 4900 lbs
2 2100 lbs 2200 lbs 2600 lbs 3400 lbs 2
8. Do not induce external side loads to boom or jib.
is 14,000 lbs with 10:00 x 15 tires. Tire inflation at
12,000 lbs. For deck loads only, the maximum load
7. The maximum combined total boom and deck load is
next larger radius.
6. For operating radius not shown, use load rating of the
on a smooth hard level surface with boom retracted
may be transported at a maximum speed of 2.5 mph
tires, and proper inflation pressure (100 psi). Loads on rubber
5. Ratings on rubber depend on tire capacity, condition of
4. Ratings on outriggers are with outriggers fully extended.
be considered as part of the load. See reductrion chart.
hook blocks, slings, etc., except the hoist rope, shall
3. The weights of all load handling devices, such as hooks,
proper handling must all be taken into account by the
Hazardous surroundings, experience of personnel and
Practical working loads depend on supporting surface,
leveled, standing on a firm, uniform supporting surface.
based on freely suspended loads with the machine
not exceed 75% of actual tipping. These ratings are
of actual tipping. The rated loads shown on rubber do
2. The rated loads shown on outriggers do not exceed 85%
the supporting surface, before loading, to the center
distance from a projection of the axis of rotation to
operating radius. The operating radius is the horizontal
of boom lengths and angles may be used to obtain
determined by operating radius only. Any combination
of vertical hoist line or tackle with load applied.
operating radius, and other factors affecting stability.
operator.
to the shortest length possible and centered over front.
at 100 psi.
RELY ON TIPPING.
DISREGARD OF IN
3-SECTION BOOM OR 4-SECTION BOOM WITH 4TH RETRA
RADIUS
OPERATING
950 lbs
1100 lbs
1300 lbs
1500 lbs
1800 lbs
2150 lbs
2750 lbs
3800 lbs
5400 lbs
8000 lbs
32.0 ft
30.0 ft
28.0 ft
26.0 ft
24.0 ft
22.0 ft
20.0 ft
18.0 ft
16.0 ft
14.0 ft
12.0 ft
10.0 ft
8.0 ft
6.0 ft
5.0 ft
2900 lbs
3300 lbs
3800 lbs
4450 lbs
33.5 ft
4650 lbs
2050 lbs
2350 lbs
2700 lbs
3150 lbs
3800 lbs
4
27.0 ft 850 lbs 52750 lbs 1900 lbs
SHADED AREAS AR
OPERATION OF TH
525 lbs
600 lbs
700 lbs
800 lbs
1875 lbs
2025 lbs
2275 lbs
2525 lbs
1300 lbs
1425 lbs
1600 lbs
1775 lbs
R
ON R
FRONT
ON OUTRIGGERS
360° FRONT
JIB STRUCTURAL CAPACITIES @ MAIN BOOM ANGLE (ALSO DO NOT EXCEED CAPACITIE
0° 15° 30° 45°
42.0 ft
40.0 ft
38.0 ft
43.0 ft
36.0 ft --
--
-
-
--
--
-
-
-- -
6000 lbs7100 lbs 8500 lbs 10200 lbs 12400 lbs15700 lbs 17000 lbs
5200 lbs
17000 lbs
5800 lbs 6950 lbs 8500 lbs 10800 lbs14400 lbs 9500 lbs
10000 lbs 8
2200 lbs 2400 lbs 2700 lbs 3000 lbs 3500 lbs
1. The rated loads are the maximum lifting capacities as
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
11
YB4400
Seri
es
YB4409-2
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
dimensions
Retracted 13’ 10” & Extended 32’ 10”(Retracted 4.22 m & Extended 10.01 m)
11’ 7.75”(3.5 m)
11’ 5.5”(3.39 m)
4’ 4”(1.32 m)
15.5”(394 m)
2’ 2”(0.51 m)
1’ 0”(0.30 m)
3’ 4.5”(1.00 m)
5’ 8.38”(1.74 m)
11’ 11.75”(3.65 m)
1’ 0”(0.30 m)
5’7”(1.70 m)
1’ 6”(0.46 m)
5’ 8.38”(1.74 m)
5’ 6.92”(1.70 m)
5’ 11.88”(1.74 m)
6’ 5”(1.96 m)
7’ 3”(2.21 m)
5’ 9.7”(1.77 m)
10”
5’ 3”(1.60 m)
9’ 2.75”(1.81 m)
10’ 2”(3.10 m)
2.5”(6.35 cm)
3’ 4.5”(1.03 m)
3’ 2.5”(.98 m)
30°
54.0”(*1.37 m)
53.0”(1.34 m)
43.5”(1.10 m)
0°*0° boom headposition can onlybe used with adown haul block
80°
Dimensions are with boom horizontaland the anti-two block bottomed.
See Insert
Dimensions are withboom horizontaland the anti-twoblock bottomed.
12
YB4400
Seri
es
range diagram
YB4409-256
54
52
50
48
46
44
42
40
38
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
0
56
54
52
50
48
46
44
42
40
38
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
0
OPERATING RADIUS IN FEET FROM AXIS OF ROTATION
6 4 2 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48
6 4 2 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48
HE
IGH
TF
RO
MG
RO
UN
DIN
FE
ET
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
13
YB4400
Seri
es
load chart
YB4409-2
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
14
YB4400
Seri
es
dimensions
11' - 7.75"(3.55 m)
YB4411 Dimensions
(1346 mm)53"
30o
(1105 mm)
43.5"80o
(1372 mm)
*54"0o
SEE
INSET
*0o boomhead position can only
be used with headache ball.
Dimensions are with the boom horizontal
and the anti-two block bottomed.
11' - 7.75"(3.55 m)
YB4411 Dimensions
(1346 mm)53"
30o
(1105 mm)
43.5"80o
(1372 mm)
*54"0o
SEE
INSET
*0o boomhead position can only
be used with headache ball.
Dimensions are with the boom horizontal
and the anti-two block bottomed.
YB4411
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
15
YB4400
Seri
es
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
40
400
4
2
6
6 4 2
20
8
10
12
14
16
18
22
24
26
30
28
32
201020 4 6 8 12 14 16 18 3022 24 26 28 32 34 36 38
15o
20o
0o
5o
10o
25o
30o
35o
40o
45o
46
36
34
38
40
42
44
48
50
52
54
566 4 2
70o
65o
60o
55o
50o
201020 4 6 8 12 14 16 18 3022 24 26 28 32 34 36 38
42 44 4846
4
2
6
20
8
10
12
14
16
18
22
24
26
30
28
32
46
36
34
38
40
42
44
48
50
52
54
5642 44 4846
72o
13'-1
0"B
OO
M
23'-4
"B
OO
M
32'-1
0"B
OO
M
44'-1
0"B
OO
M
50'-1
0"B
OO
M
WIT
H12
'-0"
JIB
WIT
H12
'-0"
JIB
&6'
-0"
ST
ING
ER
50
500
HE
IGH
TF
RO
MG
RO
UN
DIN
FE
ET
OPERATING RADIUS IN FEET FROM AXIS OF ROTATION
YB4411
range diagram
YB4400
Seri
es
16
load chart
15°
30°
15°
30°
FRONT REAR
SIDE
SIDE
0-21000 lbs2-PART
0-10000 lbs1-PART
RIGGING CHART
WIRE ROPE: 9/16 inch diameterMin. breaking strength 36750 lbs.
RATING CHARTS AND DISREGARD OF INSTRUCTIONSIS DANGEROUS AND VOIDS WARRANTY .
OPERATION OF THIS EQUIPMENT IN EXCESS OF
REDUCTION CHART
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
140 lbs
100 lbs
0 lbs
450 lbs
N/A
100 lbs
N/A
0 lbs
The rated loads are the maximum lift
capacities as determined by operating
radius, boom extension and boom
angle. The operating radius is the
horizontal distance from a projection
of the axis of rotation to the
supporting surface, before loading, to
the center of vertical hoist line or
tackle with load applied.
The rated loads shown on outriggers
do not exceed 85% of actual tipping.
The rated loads shown on rubber do
not exceed 75% of actual tipping.
These ratings are based on freely
suspended loads with the crane
leveled, standing on a firm, uniform
supporting surface. Practical working
loads depend on supporting surface,
operating radius and other factors
affecting stability. Hazardous
surroundings, climatic conditions,
experience of personnel and proper
training must all be taken into account
by the operator.
The weights of all load handling
devices such as hooks, hook blocks,
slings, etc., except the hoist rope,
shall be considered as part of the
load. See reduction chart.
1)
Ratings on rubber depend on tire
capacity, condition of tires and proper
inflation pressure (100 psi). Loads on
rubber may be transported at a
maximum speed of 2.5 mph on a
smooth hard level surface with boom
retracted to the shortest length
possible and centered over front.
For operating radius not shown, use
load rating of next larger radius.
The maximum combined total boom
and deck load is 12000 lbs. The
maximum deck load only is 14000 bs.
Do not induce any external side loads
to boom or jib.
5)
6)
7)
8)
2)
3)
Ratings on outrigggers are for either
outriggers fully extended and down or
fully retracted and down. Ratings for
outriggers fully retracted and down
will apply for any intermediate
outrigger setting.
4)
210004.0
BOOM
ON OUTRIGGERS (lbs)
MA
INB
OO
MJI
B
BOOM
(deg)ANGLE
MAINRADIUS
(ft)
RETRACTED
5.0 18000
6.0 15700
8.0 12200
10.0 10200
12.0 8400
14.0
16.0
18.0
20.0
22.0
24.0
26.0
28.0
31.0
34.0
36.0
38.0
40.0
48.0
46.0
44.0
42.0
15000
14700
14400
12200
10200
4300
2900
2600
3300
3700
6000
5000
7100
8400
41006100
12002000
8001300
1150 700
1500
1700 1050
950
20002900
2400 1600
3600
4600 3000
2400
360
940011500
8100
10000
5900
7800
11500 11500
ON RUBBER (lbs)
F/R
-
-
-
-
-
-
-
-
1200
1000
1100
1575
1425
1300
1975
1775
2300 900 500
-
-
-
-
-
-
-
-
RETRACTED F/REXTENDED 360o
EXTENDEDBOOM
21000
18000
15000
14700
375
300
325
625
525
425
850
750
6700
2100
1300
1150
1000
1800
1500
3100
2600
3800
5000
14400
9400
-
-
-
-
-
-
-
-
6700
-
-
-
-
-
-
-
-
-
5000
14400
9400
RETRACTED 360o 12 FTJIB
0OFFSET
2800
3500
1600
1300
1200
2300
7500
5700
4500
72
55
30
0
15
45
50
60
65
OFFSET15
3000
1500
1300
-
2500
2200
5100
4100
3500
OFFSET30
2550
1400
-
-
2300
2000
3500
3100
2800
OFFSET0
2450
1400
1100
1000
2150
1900
4000
3200
2800
OFFSET15
2150
1300
1100
-
1950
1750
3300
2700
2400
OFFSET30
1700
1300
-
-
1600
1500
2300
2000
1850
18 FTJIB
70 7000 4800 3400 3750 3100 2200
40 2000 1900 1800 1700 1600 1400
35 1775 1675 1600 1525 1450 1350
EXTENDEDBOOM
RETRACTEDBOOM ANY
BOOMANY
BOOM
20 13501350 - 1175 1125 -
25 1450 1400 - 1275 1200 -
10
5
1275
1225
-
-
-
- 1025
1050 -
-
-
-
700
600
500
425
350
300
275
250
350
275
200
125
75
0
0
0
-
JIB CAPACITY IS LIMITED BY BOTH STRUCTURALCAPACITY CHART AND MAIN CAPACITY CHART.
SHADED AREAS ARE GOVERNED BY STRUCTURALSTRENGTH, DO NOT RELY ON TIPPING.
JIB STRUCTURAL CAPACITIES (lbs)
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
YB4411
17
YB4400
Seri
es
1.5
0
3.0
4.6
6.1
7.6
3S
EC
TIO
N
4S
EC
TIO
N
9.1
10.7
12.2
45o
30o
60o
0o
15o
3.0 1.5 0 1.5 3.0 4.6 6.1 7.6 9.1 10.7
1.8m
JIB
3.0 1.5 0 1.5 3.0 4.6 6.1 7.6 9.1 10.7
1.5
0
3.0
4.6
6.1
7.6
9.1
10.7
12.2
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
range diagramH
EIG
HT
FR
OM
GR
OU
ND
INM
ET
ER
S
OPERATING RADIUS IN METERS FROM AXIS OF ROTATION
YB4409
DIN/ISOload chart
18
YB4400
Seri
es
ON RUBBER (kg)ON OUTRIGGERS (kg)
MA
INB
OO
MJI
B
77101.5
RADIUS(m)
1.8 7120
2.4 5620
3.0 4630
3.7 3860
4.3 3270
4.9
5.5
6.1
6.7
7.5
7.9
8.5
9.1
9.4
7710
6530
4900
3900
3000
1120
-
-
-
930
1470
1220
1800
2250
- -
1000
-
-
2100
1220
1180
2580
-
4540
4540
4380
3260
950
340
-
-
-
260
-
460
400
570
730
1970
1300
1520
590
-
-
-
480
-
770
670
930
1160
3200
2080
F/R 360o F/R 360o
3-SECTION BOOM OR4-SECTION BOOM WITH 4TH RETRACTED
ON RUBBER (kg)ON OUTRIGGERS (kg)
2770
RADIUS(m)
2770
2400
2130
2000
2000
2770
2770
2400
2130
2000
1110
780
690
870
940
1720
1310
2000
2000
920 660
1290
1080
1190
2000
1800
1540
2000
970
2770
2770
2770
2770
1080
340
210
170
150
270
250
510
420
650
820
2380
1560
1660
590
410
330
350
500
460
820
690
1010
1280
2400
2130
F/R 360o F/R 360o
4-SECTION BOOM WITH 4TH EXTENDED
BOOM
(deg)ANGLE
MAIN
4-SECTION BOOM
60
40
15
0
30
35
45
50
1305
1090
1000
1270
1225
1590
1430
1360
4-SECTION BOOM
JIB STRUCTURAL CAPACITIES (kg)
55 1510
25 1180
20 1135
5 1020
10 1055
JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL
3-SECTION BOOM OR
WITH 4TH RETRACTEDWITH 4TH EXTENDED
1304
1089
998
1270
1225
1588
1429
1361
1508
1179
1134
1021
1055
LIMIT RATINGS TO 5 350 kg WHEN 3RD SECTION IS EXTENDED ANY AMOUNT.*
0-7710 kg2-PART
0-3855 kg1-PART
RIGGING CHART
WIRE ROPE: 13mm diameter
Min. breaking strength 139.8 kN
REDUCTION CHART
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
64 kg
45 kg
0 kg
68 kg
N/A
45 kg
N/A
0 kg
1.5
1.8
2.4
3.0
3.7
4.3
4.9
5.5
6.1
6.7
7.5
7.9
8.5
9.1
9.4
FRONT REAR
SIDE
SIDE
15o
30o
15o
30o
SHADED AREAS ARE GOVERNED BY STRUCTURALSTRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OFRATING CHARTS AND DISREGARD OF INSTRUCTIONSIS DANGEROUS AND VOIDS WARRANTY.
CAPACITY CHART AND MAIN CAPACITY CHART.
1) The rated loads are the maximumlifting capacities as determined by operating radius only. Anycombination of boom lengths and angles may be used to obtainoperating radius. The operating radius is the horizontal distance from a projection of the axis ofrotation to the supporting surface,before loading, to the center ofvertical hoist line or tackle withload applied.
2) The rated loads shown on outriggers do not exceed 80% ofactual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniformsupporting surface. Practicalworking loads depend on supporting surface, operating radiusand other factors affecting stability.Hazardous suroundings, climatic conditions, experience of operatorand proper training must be takeninto account by the operator.
3) The weights of all load handlingdevices, such as hooks, hookblocks, slings, etc., except the hoistrope, shall be considered as partof the load. See reduction chart.
4) Ratings on outriggers are withoutriggers fully extended.
5) Ratings on rubber depend on tirecapacity, condition of tires andproper inflation pressure (6.9 bar).Loads on rubber may be transported at a maximum speedof 4 km/h on a smooth, hard, levelsurface with the boom retracted tothe shortest length possible and centered over the front.
6) For operating radius not shown, useload rating of next larger radius.
7) The maximum combined totalboom and deck load is 5 440 kgs.The maximum deck load only is 6 350 kgs.
8) Do not induce any external sideloads to boom or jib.
The
rated
loads
are the
maximum
lifting
capacities
as
determined
by
operating
radius
only.
Any
combination
of
boom
lengths
and
angles
may be
used to
obtain
operating
radius.
The
operating
radius is
the
horizontal
distance
from a
projection
of the
axis of
rotation
to the
supporting
surface,
before
loading,
to the
center
of
vertical
hoist line
or
tackle
with load
applied.
The
rated
loads
shown
on
outriggers
do not
exceed
80 of
actual
tipping.
The
rated
loads
shown
on
rubber
do not
exceed
75 of
actual
tipping.
These
ratings
are
based
on
freely
suspended
loads
with the
crane
leveled,
standing
on a
firm,
uniform
supporting
surface.
Practical
working
loads
depend
on
supporting
surface,
operating
radius
and
other
factors
affecting
stability.
Hazardous
surroundings,
climatic
conditions,
experience
of
personnel
and
training
must all
be
into
account
by the
operator.
The
weights
of all
load
handling
devices
such as
hooks,
YB4409
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
19
YB4400
Seri
es
YB4409XL
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
range diagram
10.7
1.5
3.00
1.5
3.0
4.6
6.1
7.6
3S
EC
TIO
N
4S
EC
TIO
N
1.50 4.63.0 7.66.1 9.1
9.1
10.7
12.2
13.7
45o
30o
60o
12.2
0o
1515oo
013.7
1.8m
JIB
15.210.73.0 1.5 1.50 4.63.0 7.66.1 9.1 12.2 13.7
1.5
3.0
4.6
6.1
7.6
9.1
10.7
12.2
13.7
15.2
HE
IGH
TF
RO
MG
RO
UN
DIN
ME
TE
RS
OPERATING RADIUS IN METERS FROM AXIS OF ROTATION
YB4409XL
20
YB4400
Seri
es
YB4409XL
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
DIN/ISOload chart
1) The rated loads are the maximumlifting capacities as determined by operating radius only. Anycombination of boom lengths and angles may be used to obtainoperating radius. The operating radius is the horizontal distance from a projection of the axis ofrotation to the supporting surface,before loading, to the center ofvertical hoist line or tackle withload applied.
2) The rated loads shown on outriggers do not exceed 80% ofactual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniformsupporting surface. Practicalworking loads depend on supporting surface, operating radiusand other factors affecting stability.Hazardous suroundings, climatic conditions, experience of operatorand proper training must be takeninto account by the operator.
3) The weights of all load handlingdevices, such as hooks, hookblocks, slings, etc., except the hoistrope, shall be considered as partof the load. See reduction chart.
4) Ratings on outriggers are withoutriggers fully extended.
5) Ratings on rubber depend on tirecapacity, condition of tires andproper inflation pressure (6.9 bar).Loads on rubber may be transported at a maximum speedof 4 km/h on a smooth, hard, levelsurface with the boom retracted tothe shortest length possible and centered over the front.
6) For operating radius not shown, useload rating of next larger radius.
7) The maximum combined totalboom and deck load is 5 443 kgs.The maximum deck load only is 6 350 kgs.
8) Do not induce any external sideloads to boom or jib.
0-7710 kg2-PART
0-3855 kg1-PART
RIGGING CHART
WIRE ROPE: 13mm diameter
Min. breaking strength 139.8 kN
REDUCTION CHART
MA
INB
OO
MJI
B
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
64 kg
45 kg
0 kg
68 kg
N/A
45 kg
N/A
0 kg
771071205625462538553220
77106530490038553150
1100
770730
820950
15701290
19302550
970880
---- -
---
580530
650
1360
11201180
236018501570
2720
1070
45354310
45353720
-
---
9060
1170
310
170140110
240190
470380
610830
24901670
-
---
240220
1670
540
340
280310
450370
770630
9301200
35802400
800
F/R 360o F/R 360o
- - --
3-SECTION BOOM OR4-SECTION BOOM WITH 4TH RETRACTED
ON RUBBER (kg)ON OUTRIGGERS (kg)
-1.5
RADIUS(m)
1.8 -2.4 22253.0 19503.7 17254.3 15404.95.56.16.77.37.98.28.59.19.8
10.211.011.6
12.812.2
--
860800
9301080
990890
700650610570 370
480440410
630540
710
1315
12001315
131513151315
1405
1120
--
--
10
604020
130100
1450
430
240220180
340270
720560
9001130
22251880
130
200180150
270230
680
400
310370
560450
1040830
1270
790
F/R 360o F/R 360o
13.1 540 350 0120
4-SECTION BOOM WITH 4TH EXTENDED
BOOM
(deg)ANGLE
MAIN
4-SECTION BOOM
60
40
15
0
3035
4550
1305
1090
1000
12701225
1590
14301360
1100
955
905
10451000
1540
12951180
4-SECTION BOOM
JIB STRUCTURAL CAPACITIES (kg)
55 1510 1405
25 1180 97520 1135 965
5 1020 92010 1055 930
3-SECTION BOOM OR
WITH 4TH RETRACTED WITH 4TH EXTENDED
2225195017251540
131513151315
1405
2225195017251540
ON RUBBER (kg)ON OUTRIGGERS (kg)
1.5
RADIUS(m)
1.82.43.03.74.34.95.56.16.77.37.98.28.59.19.8
10.211.011.6
12.812.2
13.1
FRONT REAR
SIDE
SIDE
15o
30o
15o
30o
SHADED AREAS ARE GOVERNED BY STRUCTURALSTRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OFRATING CHARTS AND DISREGARD OF INSTRUCTIONSIS DANGEROUS AND VOIDS WARRANTY.
JIB CAPACITY IS LIMITED BY BOTH STRUCTURALCAPACITY CHART AND MAIN CAPACITY CHART.
21
YB4400
Seri
es
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
10o
5o
0o
15o
20o
25o
30o
35o
40o
45o
50o
55o
60o
65o
72o
70o
1.8 1.2 0.6 0 0.6 1.2 1.8 2.4 3.0 3.7 4.3 4.9 5.5 6.1 6.7 7.3 7.9 8.5 9.1 9.8 10.4 11.0 11.6 12.2 12.8 13.4 14.0 14.6 15.2
1.8 1.2 0.6 0 0.6 1.2 1.8 2.4 3.0 3.7 4.3 4.9 5.5 6.1 6.7 7.3 7.9 8.5 9.1 9.8 10.4 11.0 11.6 12.2 12.8 13.4 14.0 14.6 15.217.1
16.5
15.9
15.2
14.6
14.0
13.4
12.8
12.2
11.6
11.0
10.4
9.8
9.1
8.5
7.9
7.3
6.7
6.1
5.5
4.9
4.3
3.7
3.0
2.4
1.8
1.2
0.6
0
17.1
16.5
15.9
15.2
14.6
14.0
13.4
12.8
12.2
11.6
11.0
10.4
9.8
9.1
8.5
7.9
7.3
6.7
6.1
5.5
4.9
4.3
3.7
3.0
2.4
1.8
1.2
0.6
0
3.7 m JIB 5.5m JIB
HE
IGH
TF
RO
MG
RO
UN
DIN
ME
TE
RS
OPERATING RADIUS IN METERS FROM AXIS OF ROTATION
YB4409-2
range diagram
22
YB4400
Seri
es
0-8160 kg2-PART
0-4540 kg1-PART
RIGGING CHART
WIRE ROPE: 14 mm diameter
Min. breaking strength 161.3 kN
REDUCTION CHART
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
60 kg
45 kg
0 kg
200 kg
N/A
45 kg
N/A
0 kg
1) The rated loads are the maximumlift capacities as determined by operating radius, boom extension and boom angle. The operating radius is the horizontaldistance from a projection of the axis of rotation to the supporting surface,before loading, to the center ofvertical hoist line or tackle with load applied.
The rated loads shown on outriggers do not exceed 80% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface.Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account bythe operator.
2)
The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered as part of the load. See reduction chart.
Ratings on outrigggers are for outriggers fully extended.
Ratings on rubber depend on tirecapacity, condition of tires and proper inflation pressure (700 kPa). Loads on rubber may betransported at a maximum speed of 1.4 km/h on a smooth hard levelsurface with boom retracted to the shortest length possible and centered over front.
For operating radius not shown, use load rating of next larger radius.
The maximum combined total boom and deck load is 5440 kg. The maximum deck load only is 6530 kg.
Do not induce any external side loads to boom or jib.
5)
6)
7)
8)
3)
4)
FRONT REAR
SIDE
SIDE
15o
30o
15o
30o
SHADED AREAS ARE GOVERNED BY STRUCTURALSTRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OFRATING CHARTS AND DISREGARD OF INSTRUCTIONSIS DANGEROUS AND VOIDS WARRANTY.
JIB CAPACITY IS LIMITED BY BOTH STRUCTURALCAPACITY CHART AND MAIN CAPACITY CHART.
BOOM
(deg)ANGLE
MAIN3.7 m JIB
0o
OFFSET
12701590
730
590
540
1040
3400
25902040
72
55
30
0
15
4550
6065
OFFSET15o
1360
680
590
-
11301000
2310
18601590
OFFSET30o
1160
640
-
-
1040910
1590
14101270
OFFSET0o
1110
640
500
450
980860
1810
14501270
OFFSET15o
980
590
500
-
880790
1500
12201090
OFFSET30o
770
590
-
-
730680
1040
910840
5.5 m JIB
JIB STRUCTURAL CAPACITIES (kg)
70 3180 2180 1540 1700 1410 1000
40 910 860 820 770 730 64035 810 760 730 690 660 610
20 610610 - 530 510 -25 660 640 - 580 540 -
105
580560
--
-- 460
480 --
--
BOOM
ON OUTRIGGERS (kg)
MA
INB
OO
MJI
B
RADIUS(m)
RETRACTED
1.5 81601.8 71202.4 55303.0 46303.7 38104.34.95.56.16.77.37.98.59.4
10.411.011.612.2
14.614.013.412.8
6670653055304630
2010
12401090
14301670
28102450
32703810
15502440
420700
220400330 170
480570 340
280
6601050850 520
13301730 1130
840
360o
42605220
36704540
22403360
ON RUBBER (kg)
F/R
--
------
460
430440
630560490
780710
920 250 120
-
--
---
-
-
EXTENDEDBOOM
8160 6670
320
270300
460400350
590530
4130
1490
910810690
12501060
22201800
28003450
65305170
-
--
---
--
4130
-
-
--
--
--
-3450
68005170
EXTENDEDBOOM
RETRACTEDBOOM ANY
BOOMANY
BOOM
1801501108050403020
70401000000
-
F/R 360o
YB4409-2
DIN/ISOload chart
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
0
15o
20o
0o
5o
10o
25o
30o
35o
40o
45o
70o
65o
60o
55o
50o
0
72o
4.2
mBO
OM
7.1
mBO
OM
10.0
mBO
OM
13.7
mBO
OM
15.5
mBO
OM
WIT
H3.
7m
JIB
WIT
H3.
7m
JIB
&1.
8m
STIN
GER
1230
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
3 2 1 31 2 4 5 6 7 8 9 10 11 12 13 14 15
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
HE
IGH
TF
RO
MG
RO
UN
DIN
ME
TE
RS
OPERATING RADIUS IN METERS FROM AXIS OF ROTATION
YB4411
23
YB4400
Seri
es
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
range diagram
0-9530 kg2-PART
0-4540 kg1-PART
RIGGING CHART
95301.2
WIRE ROPE: 14 mm diameter
Min. breaking strength 172.8 kN
SHADED AREAS ARE GOVERNED BY STRUCTURAL
OPERATION OF THIS EQUIPMENT IN EXCESS OF
REDUCTION CHART
BOOM
ON OUTRIGGERS (kg)
MA
INB
OO
MJI
B
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
60 kg
45 kg
0 kg
200 kg
N/A
45 kg
N/A
0 kg
BOOM
(deg)ANGLE
MAINRADIUS
(m)
RETRACTED
1.5 8160
1.8 7120
2.4 5530
3.0 4630
3.7 3810
4.3
4.9
5.5
6.1
6.7
7.3
7.9
8.5
9.4
10.411.0
11.6
12.2
14.6
14.0
13.4
12.8
6800
6670
6530
5530
4630
1790
1190
1060
1360
1530
2720
2270
3220
3810
18102720
540860
320540
480 270
630
730 430
380
8201270
1040 680
1590
2040 1310
1040
360o
42605220
3670
4540
2680
3540
5220 5220
ON RUBBER (kg)
F/R
-
-
-
-
-
-
-
-
460
380
420
620
560
510
790
710
930 360 180
-
-
-
-
-
-
-
-
RETRACTED F/REXTENDED 360o
EXTENDEDBOOM
9530
8160
6800
6670
110
80
90
220
180
130
310
270
2810
850
510
440
380
720
590
1270
1060
1570
2090
6530
3960
-
-
-
-
-
-
-
-
2810
-
-
-
-
-
-
-
-
-
2090
6530
3960
RETRACTED 360o 3.7 m JIB
0o
OFFSET
1270
1590
730
590
540
1040
3400
2590
2040
72
55
30
0
15
45
50
60
65
OFFSET15o
1360
680
590
-
1130
1000
2310
1860
1590
OFFSET30o
1160
640
-
-
1040
910
1590
1410
1270
OFFSET0o
1110
640
500
450
980
860
1810
1450
1270
OFFSET15o
980
590
500
-
880
790
1500
1220
1090
OFFSET30o
770
590
-
-
730
680
1040
910
840
5.5 m JIB
JIB STRUCTURAL CAPACITIES (kg)
70 3180 2180 1540 1700 1410 1000
40 910 860 820 770 730 640
35 810 760 730 690 660 610
EXTENDEDBOOM
RETRACTEDBOOM ANY
BOOMANY
BOOM
20 610610 - 530 510 -
25 660 640 - 580 540 -
10
5
580
560
-
-
-
- 460
480 -
-
-
-
270
230
180
150
110
90
80
70
110
80
40
10
0
0
0
0
-
JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL
FRONT REAR
SIDE
SIDE
STRENGTH, DO NOT RELY ON TIPPING.
RATING CHARTS AND DISREGARD OF INSTRUCTIONS
15o
30o
15o
30o
IS DANGEROUS AND VOIDS WARRANTY.
CAPACITY CHART AND MAIN CAPACITY CHART.
4)
5)
6)
7)
8)
Ratings on outriggers are withoutriggers fully extended.
Ratings on rubber depend on tirecapacity, condition of tires and proper inflation pressure (6.9 bar).Loads on rubber may be transported at a maximum speed of4 km/h on a smooth, hard, level surface with the boom retracted to the shortest length possible and centered over the front.
For operating radius not shown, use load rating of next larger radius.
The maximum combined total boom and deck load is 5 440 kgs. The maximum deck load only is 6 350kgs.
Do not induce any external side loads to boom or jib.
1)
2)
3)
The rated loads are the maximum lifting capacities as determined by operating radius only. Any combination of boom lengths and angles may be used to obtain operating radius. The operatingradius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with loadapplied.
The rated loads shown on outriggers do not exceed 80% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operatingradius and other factors affecting stability. Hazardous suroundings,climatic conditions, experience of operator and proper training must be taken into account by the operator.
The weights of all load handlingdevices, such as hooks, hookblocks, slings, etc., except thehoist rope, shall be considered as part of the load. See reduction chart.
24
YB4400
Seri
es
YB4411
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
DIN/ISOload chart
25
YB4400
Seri
es
notes
notes
26
YB4400
Seri
es
27
YB4400
Seri
es
notes
Constant improvement and engineering progressmake it necessary that we reserve the right to makespecification, equipment and price changes withoutnotice. Illustrations shown may include optionalequipment and accessories, and may not include allstandard equipment.
AmericasBrazilAlphavilleTel: +55 11 3103 0200Fax: +55 11 4688 2013
MexicoMonterreyTel: +52 81 8124 0128Fax: +52 81 8124 0129
Europe, Middle East, AfricaAlgeriaHydraTel: +21 3 21 48 1173Fax: +21 3 21 48 1454
Czech RepublicNetvoriceTel: +420 317 78 9313Fax: +420 317 78 9314
FranceBaudemontTel: +33 385 28 2589Fax: +33 385 28 0430
CergyTel: +33 130 31 3150Fax: +33 130 38 6085
DecinesTel: +33 472 81 5000Fax: +33 472 81 5010
GermanyLangenfeldTel: +49 21 73 8909-0Fax: +49 21 73 8909 30
HungaryBudapestTel: +36 13 39 8622Fax: +36 13 39 8622
ItalyParabiagoTel: +390 331 49 3311Fax: +390 331 49 3330
NetherlandsBredaTel: +31 76 578 3999 Fax: +31 76 578 3978
PolandWarsawTel: +48 22 843 3824Fax: +48 22 843 3471
PortugalAlfenaTel: +351 229 69 8840Fax: +351 229 69 8848
LisbonTel: +351 212 109 340Fax: +351 212 109 349
RussiaMoscowTel: +7 495 641 2359Fax: +7 495 641 2358
U.A.E.DubaiTel: +971 4 3381 861Fax: +971 4 3382 343
U. K.MiddlesexTel: +44 1 895 43 0053Fax: +44 1 895 45 9500
SunderlandTel: +44 191 522 2000Fax: +44 191 522 2052
Asia – PacificAustraliaMelbourneTel: +61 3 9 336 1300Fax: +61 3 9 336 1322
SydneyTel: +61 2 9 896 4433Fax: +61 2 9 896 3122
ChinaBeijingTel: +86 10 58674761Fax: +86 10 58674760
Xi’anTel: +86 29 87891465Fax: +86 29 87884504
KoreaSeoulTel: +82 2 3439 0400Fax: +82 2 3439 0405
PhilippinesMakati CityTel: +63 2 844 9437Fax: +63 2 844 4712
Factories
BrazilAlphaville
ChinaZhangjiagang
FranceCharlieuLa ClayetteMoulins
GermanyWilhelmshaven
IndiaCalcuttaPune
ItalyNiella Tanaro
PortugalBaltarFânzeres
SlovakiaSaris
U.S.A.ManitowocPort WashingtonShady Grove
Regional Offices
AmericasManitowoc, Wisconsin, USATel: +1 920 684 6621Fax: +1 920 683 6278
Shady Grove, Pennsylvania, USATel: +1 717 597 8121Fax: +1 717 597 4062
Europe, Middle East, AfricaEcully, FranceTel: +33 472 18 2020Fax: +33 472 18 2000
Asia – PacificShanghai, ChinaTel: +86 21 51113579Fax: +86 21 51113578
SingaporeTel: +65 6264 1188Fax: +65 6862 4142
Regional Headquarters
©2007 MANITOWOCPrinted in USA Form No. YB4400 Series Part No. 04-019 / 0108 / 2M
www.manitowoccranegroup.com