Yamaha-RXV1200_2200 rec.pdf

RX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200SERVICE MANUAL

AV RECEIVER

RX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

IMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users, and have therefore not been restated.

WARNING:

Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributor's Service Division.

WARNING:

Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.

I CONTENTSTO SERVICE PERSONNEL .......................................... 1 IMPEDANCE SELECTOR ............................................. 1 FRONT PANELS ........................................................ 2~3 REAR PANELS .......................................................... 3~7 REMOTE CONTROL TRANSMITTER .......................... 8 SPECIFICATIONS .................................................... 9~10 INTERNAL VIEW ......................................................... 11 DISASSEMBLY PROCEDURES ........................... 12~14 SELF DIAGNOSIS FUNCTION (DIAG) ................. 15~36 AMP ADJUSTMENT .................................................... 36 DISPLAY DATA ..................................................... 37~38 IC DATA ................................................................. 39~45 BLOCK DIAGRAM ................................................. 46~49 PRINTED CIRCUIT BOARD .................................. 50~89 PIN CONNECTION DIAGRAM .............................. 90~91 SCHEMATIC DIAGRAM ........................................ 92~99 PARTS LIST ....................................................... 100~126 REMOTE CONTROL TRANSMITTER .............. 127~130

100792P.O.Box 1, Hamamatsu, Japan

RX-V1200/RX-V1200RDS/HTR-5490/RX-V2200

I TO SERVICE PERSONNELRX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

1. Critical Components Information Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits.G

WALL OUTLET

EQUIPMENT UNDER TEST

AC LEAKAGE TESTER OR EQUIVALENT

Meter impedance should be equivalent to 1500 ohm shunted by 0.15F. Leakage current must not exceed 0.5mA. Be sure to test for leakage with the AC plug in both polarities.

INSULATING TABLE

G G

CAUTION F201, F202: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 8A, 125V FUSE. CAUTION F201, F202: REPLACE WITH SAME TYPE 8A, 125V FUSE. ATTENTION F201, F202: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 8A, 125V.

WARNING: CHEMICAL CONTENT NOTICE!The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food. DIMENSIONS

I IMPEDANCE SELECTOR

394 (15-1/2") 150 (5-7/8")435 (17-1/8") Unit : mm (inch)

IMPEDANCE SELECTOR WARNING: Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged.

1

21 (13/16")

171 (6-3/4")

16 (5/8")

431.5 (17")

21.5 (7/8")


I FRONT PANELSRX-V1200 (U, C, A, R, T, K models)RX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

RX-V1200RDS (B, G models)

HTR-5490 (U, C, A, T models)

2


RX-V2200 (U, C, A, R, T models)


I REAR PANELSRX-V1200 (U model)

RX-V1200 (C model)

3


RX-V1200 (A model)


RX-V1200 (R, T, K models)

RX-V1200RDS (B model)

4


RX-V1200RDS (G model)


HTR-5490 (U model)

HTR-5490 (C model)

5


HTR-5490 (A model)


HTR-5490 (T model)

RX-V2200 (U model)

6


RX-V2200 (C model)


RX-V2200 (A model)

RX-V2200 (R, T models)

7


I REMOTE CONTROL TRANSMITTERRX-V1200/HTR-5490 (U, C, A, R, T, K models) RX-V1200RDS (B, G models) RX-V2200RX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

RAV230V754580 US

8


I SPECIFICATIONSI Audio Section Minimum RMS Output Power (Power Amp. Section) RX-V1200/RX-V1200RDS/HTR-5490 (20 Hz to 20 kHz, 0.04% THD, 8 ohms) MAIN L/R ..................................................................... 80W + 80W CENTER ................................................................................. 80W REAR L/R/C .................................................... 80W + 80W + 80W (1 kHz, 0.04% THD, 8 ohms) MAIN L/R [U, C models] ............................................................ 95W + 95W [A, B, G, R, T, K models] .......................................... 90W + 90W CENTER [U, C models] ....................................................................... 95W [A, B, G, R, T, K models] ..................................................... 90W REAR L/R/C [U, C models] ................................................ 95W + 95W + 95W [A, B, G, R, T, K models] .............................. 90W + 90W + 90W RX-V2200 (20 Hz to 20 kHz, 0.04% THD, 8 ohms) MAIN L/R ................................................................. 100W + 100W CENTER ............................................................................... 100W REAR L/R/C .............................................. 100W + 100W + 100W (1 kHz, 0.04% THD, 8 ohms) MAIN L/R ................................................................. 115W + 115W CENTER ............................................................................... 115W REAR L/R/C .............................................. 115W + 115W + 115W Maximum Power (EIAJ) RX-V1200/HTR-5490 [R, T, K models] (1 kHz, 10% THD, 8 ohms) MAIN L/R ................................................................. 125W + 125W CENTER ............................................................................... 125W REAR L/R/C .............................................. 125W + 125W + 125W RX-V2200 [R, T models] (1 kHz, 10% THD, 8 ohms) MAIN L/R ................................................................. 155W + 155W CENTER ............................................................................... 155W REAR L/R/C .............................................. 155W + 155W + 155W Dynamic Power Per Channel (IHF) RX-V1200/RX-V1200RDS/HTR-5490 MAIN L/R (8/6/4/2 ohms) ............................... 105/130/170/200 W RX-V2200 MAIN L/R (8/6/4/2 ohms) ............................... 130/160/200/245 W DIN Standard Output Power Per Channel RX-V1200RDS [G model] (1 kHz, 0.7% THD, 4 ohms) MAIN L/R ................................................................. 135W + 135W CENTER ............................................................................... 135W REAR L/R/C .............................................. 135W + 135W + 135W Dynamic Headroom RX-V1200/HTR-5490 (8 ohms) [U model] ........................................................................... 1.2 dB [C model] ........................................................................... 1.1 dB RX-V2200 (8 ohms) [U, C models] .................................................................... 1.1 dB IEC Power RX-V1200RDS [G model] MAIN L/R (1 kHz, 0.04% THD, 8 ohms) ..................... 90W + 90W Damping Factor MAIN L/R (20 Hz to 20 kHz, SPEAKER-A, 8 ohms) ... 80 or more Input Sensitivity / Input Impedance PHONO (MM) ................................................. 2.5 mV / 47 k-ohms CD, etc. ......................................................... 150 mV / 47 k-ohms EXT. DECODER MAIN L/R ................................................... 150 mV / 47 k-ohms CENTER, SURROUND L/R, SUBWOOFER ... 150 mV / 40 k-ohms Maximum Input Signal Level PHONO (MM) (1 kHz, 0.1% THD) .................................... 100 mV CD, etc. (1 kHz, 0.5% THD, EFFECT ON) ........................... 2.2 V Output Level / Output Impedance REC OUT ..................................................... 150 mV / 0.9 k-ohms PRE OUT ....................................................... 2.57 V / 1.2 k-ohms SUB WOOFER [MAIN SP: Small] ................... 4.0 V/1.2 k-ohms Headphone Jack Rated Output / Impedance 1 kHz, 40 mV, 8 ohms ..................................... 0.15 V / 100 ohms Frequency Response CD, etc. to MAIN (10 Hz to 100 kHz) ................................ 0/-3 dB Power Amp. section (5 Hz to 100 kHz) ............................. 0/-3 dB RIAA Equalization Deviation PHONO (MM) (20 Hz to 20 kHz) .................................... 00.5 dB Total Harmonic Distortion (20 Hz to 20 kHz) PHONO (MM) to REC OUT (1V) .................................. 0.02% or less CD, etc. (EFFECT OFF) to MAIN SP OUT (50W /8 ohms) .. 0.04% or less Signal to Noise Ratio (IHF-A network) (Input shorted) PHONO (MM) to REC OUT (5 mV) [U, C, R, T, K models] ........................................... 86 dB or more [A, B, G models] .................................................... 81 dB or more CD, etc. (EFFECT OFF) to MAIN SP OUT 250 mV ................................................................ 100 dB or moreRX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

Residual Noise (IHF-A netwok) MAIN L/R SP OUT ................................................. 150 V or less Channnel Separation (Vol -30 dB, EFFECT OFF) PHONO (Input shorted, 1 kHz/10 kHz) .... 60 dB or more/55 dB or more CD, etc. (Input 5.1 k-ohms shorted, 1 kHz/10 kHz) ... 60 dB or more/45 dB or more Tone Control Characteristics Bass: Boost/Cut ................................................ 10 dB (50 Hz) Turnover Frequency ............................................ 350 Hz Treble: Boost/Cut .............................................. 10 dB (20 kHz) Turnover Frequency ........................................... 3.5 kHz Filter Characteristics MAIN, Rear SP Small (H.P.F.) .......................... 90 Hz, 12 dB/oct. SUBWOOFER (L.P.F.) ...................................... 90 Hz, 18 dB/oct. Bass Extension 60 Hz ...................................................................................... 6 dB I Video Section S-Video Signal Type [U, C models] ....................................................................... NTSC [R, T, K models] ....................................................... NTSC or PAL [A, B, G models] ...................................................................... PAL Video Signal Level ............................................................................ 1 Vp-p / 75 ohms S-Video Signal Level Y ......................................................................... 1 Vp-p / 75 ohms C .................................................................. 0.286 Vp-p / 75 ohms Component Signal Level Y ......................................................................... 1 Vp-p / 75 ohms Cb/Cr ............................................................... 0.7 Vp-p / 75 ohms Maximum Input Level .......................................................................................... 1.5 Vp-p Signal to Noise Ratio ................................................................................. 50 dB or more Monitor Out Frequency Response S-Video Signal Level ................................. 5 Hz to 10 MHz, -3 dB Component Signal Level .............................. DC to 60 MHz, -3 dB I FM Section Tuning Range [U, C models] ................................................... 87.5 to 107.9 MHz [A, B, G models] ........................................... 87.50 to 108.00 MHz [R, T, K models] .................. 87.5 to 108.0 / 87.50 to 108.00 MHz 50 dB Quieting Sensitivity (IHF) (100% Mod) Mono .................................................................. 2.0 V (17.3 dBf) Stereo .................................................................. 25 V (39.2 dBf) Usable Sensitivity (IHF) Mono .................................................................. 1.0 V (11.2 dBf) Selectivity at 400 kHz ............................................................................ 70 dB Signal to Noise Ratio (IHF) Mono / Stereo .......................................................... 76 dB / 70 dB Harmonic Distortion (1 kHz) Mono/Stereo ................................................................. 0.2 / 0.3 % Stereo Separation 1 kHz .................................................................................... 45 dB Frequency Response 20 Hz to 15 kHz .......................................................... +0.5 / -2 dB Antenna Input ...................................................................... 75 ohms unbalanced I AM Section Tuning Range [U, C models] ..................................................... 530 to 1,710 kHz [A, B, G models] ................................................. 531 to 1,611 kHz [R, T, K models] ......................... 530 to 1,710 / 531 to 1,611 kHz Usable Sensitivity ........................................................................................ 300 V/m Antenna ................................................................................. Loop Antenna I General Power Supply [U, C models] ...................................................... AC 120 V, 60 Hz [A model ] ............................................................ AC 240 V, 50 Hz [B, G models] ...................................................... AC 230 V, 50 Hz [R model] .................................. AC 110/120/220/240 V, 50/60 Hz [T model ] ............................................................ AC 220 V, 50 Hz [K model ] .................................................... AC 110/220 V, 60 Hz Power Consumption RX-V1200/RX-V1200RDS/HTR-5490 [U model] ............................................................................. 260 W [C model] .............................................................. 270 W / 370 VA [A, B, G, R, T, K models] .................................................... 360 W RX-V2200 [U model] ............................................................................. 390 W [C model] .............................................................. 400 W / 500 VA [A, R, T models] .................................................................. 410 W Standby Power Consumption (reference data) [U, C, A, B, G models] ......................................................... 1.2 W

9


[R, T models] AC 220V, 50Hz ............................................. 1.5 W [K model] AC 220V, 60Hz .................................................... 1.5 W Maximum Power Consumption RX-V1200/RX-V2200 [R model] 5ch Drive, 10% THD ........................................................... 585 W AC Outlets 2 switched outlets [U, C models] ..................................................... 80W max., total [G model] RX-V1200RDS only ....................... 100W max., total [R, T models] ...................................................... 50W max., total 1 switched outlet [A, B models] B: RX-V1200RDS only ...................... 100W max. Dimensions (W x H x D) ............................. 435 x 171 x 431.5 mm (17-1/8" x 6-3/4" x 17") Weight .................................................................... 15.0 kg (33 lbs. 1 oz.) Finish RX-V1200 ................................... Gold color (R, T, K) models Black color (U, C, R, A) moleds RX-V1200RDS ........................... Gold color (G) model Black color (B, G) models Titan color (B, G) moldels HTR-5490 ................................... Gold color (T) model Black color (U, C, A) models RX-V2200 ................................... Gold color (R, T) models Black color (U, C, R, A) models Accessories

Remote control transmitter, Manganese batteries, Indoor FM antenna, AM loop antenna, Antenna adaptor [B model], Power cord ass'y [V1200/V2200 U, C models]RX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

* Specifications are subject to change without notice due to product improvements. U .......... A .......... G .......... T .......... U.S.A. model Australian model European model Chinese model C B R K ...... Canadian model ...... British model ...... General model ...... Korean model

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories.

DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems, Inc.

Set Menu TableNo. 1. 1A 1B 1C 1D 1E 1F 2. SET MENU SPEAKER SET CENTER SPEAKER MAIN SPEAKER REAR L/R SPEAKER REAR CENTER SPEAKER LFE/BASS OUT MAIN LEVEL LOW FREQ. TEST PRESET VALUE LARGE LARGE LARGE LARGE BOTH NORMAL TEST TONE : OFF OUTPUT : MAIN L/R FREQ. : 88Hz CENTER HP BASS : 0dB HP TREBLE : 0dB 100Hz : 0dB 300Hz : 0dB 1kHz : 0dB 3kHz : 0dB 10kHz : 0dB DVD (Currently selected input) [A] : DVD [B] : D-TV/LD (1) : MD/TAPE (2) : CD-R (3) : CD (4) : CD-R (5) : DVD (6) : D-TV/LD (7) : CD (8) : CBL/SAT AUTO PARAMETER INITIALIZE SPEAKER : 0dB HEADPHONE : 0dB SP DYNAMIC RANGE : MAX HP DYNAMIC RANGE : MAX CENTER : 0ms REAR CENTER : 3ms BLUE BACK : AUTO OSD SHIFT : 0 DIMMER : 0 OFF MAIN SETTING RANGES LARGE, SMALL, NONE LARGE, SMALL LARGE, SMALL, NONE LARGE, SMALL, NONE SUBWOOFER, MAIN, BOTH NORMAL, 10dB OFF, ON MAIN L/R, L, C, R, RS, RC, LS, SWFR 35Hz/ /88Hz/ /WIDE L, , CENTER, , R (40 steps) 6dB +3dB (1dB step) 6dB +3dB (1dB step) 6dB +6dB (1dB step) 6dB +6dB (1dB step) 6dB +6dB (1dB step) 6dB +6dB (1dB step) 6dB +6dB (1dB step)

3. 4. 5.

L/R BALANCE HP TONE CONTROL CENTER GRAPHIC EQ.

6. 7. 7A 7B 7C

7D 8. 9. 10. 11. 12. 13.

INPUT RENAME I/O ASSIGNING COMPONENT VIDEO INPUT 1 COMPONENT VIDEO INPUT 2 OPTICAL OUT 1 OPTICAL OUT 2 OPTICAL IN 1 OPTICAL IN 2 OPTICAL IN 3 OPTICAL IN 4 COAXIAL IN 1 COAXIAL IN 2 INPUT MODE PARAMETER INITIALIZE LFE LEVEL DYNAMIC RANGE SPEAKER DELAY TIME DISPLAY SET

14. 15.

MEMORY GUARD DUAL MONO

DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, V-AUX DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, V-AUX DVD, MD/TAPE, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, V-AUX, PHONO, CD, CD-R DVD, MD/TAPE, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, V-AUX, PHONO, CD, CD-R CD, CD-R, MD/TAPE, DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, PHONO CD, CD-R, MD/TAPE, DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, PHONO CD, CD-R, MD/TAPE, DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, PHONO CD, CD-R, MD/TAPE, DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, PHONO CD, CD-R, MD/TAPE, DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, V-AUX, PHONO CD, CD-R, MD/TAPE, DVD, D-TV/LD, CABLE, SAT, VCR1, VCR2/DVR, V-AUX, PHONO AUTO/LAST The number key of the remote controller is pushed and initialized. 2dB 0dB (1dB step) 2dB 0dB (1dB step) MAX, STD, MIN MAX, STD, MIN 0ms 5ms (1ms step) 0ms 30ms (1ms step) AUTO/OFF 5 +5 (1 step) 4 0 (1 step) ON/OFF MAIN, SUB, ALL

10


The variable range of the parameter (Min/Max/Step)Parameter nameRX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

Pro Logic 10/25/1 -

(P.) INIT. DLY (P.) ROOM SIZE (P.) LIVENESS S. DELAY S. INIT. DLY S. ROOM. SIZE S. LIVENESS RC. INT.DLY RC. ROOM, SIZE RC. LIVENESS REV. TIME REV. DELAY REV. LEVEL Panorama Dimension C Width 6ch Stereo Parameter CT. LEVEL RL. LEVEL RC. LEVEL RR. LEVEL

Pro Logic II Pro Logic II Movie Music 10/25/1 0/15/1 OFF OFF/ON 0 (STD) -3/+3/1 0 0/7/1 Unit % % % %

Neo:6 0/30/1 -

2ch 1/99/1 0.1/2.0/0.1 0/10/1 0/49/1 0.1/2.0/0.1 0/10/1 1.0/5.0/0.1 0/250/1 0/100/1 -

DD/dts/AAC 1/99/1 0.1/2.0/0.1 0/10/1 0/49/1 1/49/1 0.1/2.0/0.1 0/10/1 1.0/5.0/0.1 0/250/1 0/100/1 -

6.1/ES 1/99/1 0.1/2.0/0.1 0/10/1 0/49/1 1/49/1 0.1/2.0/0.1 0/10/1 1/49/1 0.1/2.0/0.1 0/10/1 1.0/5.0/0.1 0/250/1 0/100/1 -

Unit ms ms ms ms s ms % -

0/100/1 0/100/1 0/100/1 0/100/1

I INTERNAL VIEW1 POWER (1) P.C.B. 2 POWER (7) P.C.B. 3 MAIN (6) P.C.B. 4 MAIN (4) P.C.B. 5 MAIN (5) P.C.B. 6 POWER (10) P.C.B. 7 TUNER 8 VIDEO (4) P.C.B. 9 VIDEO (2) P.C.B. 0 VIDEO (1) P.C.B. A VIDEO (6) P.C.B. B VIDEO (8) P.C.B. C VIDEO (7) P.C.B. D VIDEO (5) P.C.B. E DSP P.C.B. F FUNCTION P.C.B. G POWER (4) P.C.B. H MAIN (1) P.C.B. I OPERATION (5) P.C.B. J OPERATION (4) P.C.B. K MAIN (2) P.C.B. L OPERATION (2) P.C.B. M POWER (8) P.C.B. N OPERATION (6) P.C.B. (RX-V2200 only) O OPERATION (1) P.C.B. P OPERATION (3) P.C.B. Q POWER (3) P.C.B. R OPERATION (7) P.C.B. S POWER (5) P.C.B. T POWER (2) P.C.B. U MAIN (7) P.C.B. V MAIN (3) P.C.B. 11

1

2 3 4 5 6 78 9 0 A

B C V U T S R Q D E

F G H

N M P O L

K J I


I DISASSEMBLY PROCEDURES(Remove parts in the order as numbered.) Disconnect the power cord from the AC outlet. 1. Removal of Top Cover a. Remove 2 screws (1), 4 screws (2) and 5 screws (3). (Fig. 1) b. Slide the Top Cover rearward to remove it. (Fig. 1) 2. Removal of Front Panel a. Remove the BASS and TREBLE knobs (4). (Fig. 1) b. Remove 9 screws (5) and then remove the Front Panel forward. (Fig. 1) 3. Removal of Sub Chassis a. Remove 4 push rivets (6) and then remove the Side Plates. (Fig. 2) b. Remove 2 screws (7) and 2 screws (8), and then remove the Sub Chassis forward. (Fig. 2) 4. Removal of DSP P.C.B. a. Remove 2 screws (9) and then remove the Supports. (Fig. 2) b. Remove 4 screws (0) and then remove the Brackets. (Fig. 2) c. Remove 1 screw (A). (Fig. 2) d. Remove 9 screw (B). (Fig. 3) e. Remove the DSP P.C.B. upward. (Fig. 2) 5. Removal of VIDEO (5) P.C.B. a. Remove 2 screws (C). (Fig. 2) b. Remove the VIDEO (5) P.C.B. which is connected directly to the lower P.C.B. with connectors. (Fig. 2)Top Cover

3 2 1RX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

3

5 2

5Front Panel

4Fig. 1

CSide Plate L

6 7VIDEO (5) P.C.B. DSP P.C.B. Support

6

9

0

8 6Sub Chassis

A

0 00Bracket

8Side Plate R

7 6

Fig. 2

B

E

DFig. 3 12



6. Removal of VIDEO (1), VIDEO (2), VIDEO (4) and VIDEO (8) P.C.B.s and Tuner a. Remove 17 screws (D). (Fig. 3) b. Remove VIDEO (1), VIDEO (2), VIDEO (4) and VIDEO (8) P.C.B.s and the Tuner. (Fig. 4) When checking the P.C.B.: Put the rubber sheet and a cloth over the equipment. Then place the P.C.B. upside down on the cloth and check it. (Fig. 4) Connect VIDEO (5) and FUNCTION P.C.B.s by using the extension cable (AAX30610) for the P.C.B. check. (Fig. 6) Reconnect all cables (connectors) that have been disconnected. The P.C.B. removed from the rear panel does not work because its grounding is loose. Be sure to connect the ground of each P.C.B. to the chassis or GND with a jumper wire or the like.

VIDEO (8)P.C.B. VIDEO (1)P.C.B. VIDEO (5)P.C.B. Rubber sheet and cloth

VIDEO (2)P.C.B. VIDEO (4)P.C.B. Extension cable

Tuner

Fig. 4

7. Removal of VIDEO (6), VIDEO (7), and FUNCTION P.C.B.s a. Remove CB212, CB975, CB510, CB509, CB505 and CB503. (Fig. 5) b. Remove 9 screws (E). (Fig. 3) c. Remove VIDEO (6), VIDEO (7), and FUNCTION P.C.B.s. (Fig. 6) When checking the P.C.B.: Put a cloth beside the equipment. Then place the P.C.B. on the cloth and check it. (Fig. 4) Connect VIDEO (5) and FUNCTION P.C.B.s by using the extension cable (AAX30610) for the P.C.B. check. (Fig. 6) Reconnect all cables that have been disconnected. The P.C.B. removed from the rear panel does not work because its grounding is open. Be sure to connect the ground of each P.C.B. to the chassis or GND with a jumper wire or the like.FUNCTION P.C.B. Block and cloth CB212

CB503

CB510 CB509

CB975

CB505

Fig. 5

VIDEO (6) P.C.B. VIDEO (7) P.C.B.

Extension cable (AAX30610)

Fig. 6 13


8. Removal of Duct/Fan Section (If applicable) a. Remove 2 screws (F) and 2 screws (G). (Fig. 7) b. Remove the duct/fan together with the frame by lifting them up.

Duct/Fan

Frame

GRX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

G

FFig. 7

9. Removal of MAIN (1), MAIN (2), POWER (4) and POWER (8) P.C.B.'s. a. Remove 2 screws (H), 3 screws (I) and 1 screw (J). (Fig. 8) b. Remove MAIN (1), MAIN (2), POWER (4) and POWER (8) P.C.B.s. (Fig. 8)

MAIN (2) P.C.B. POWER (4) P.C.B. POWER (8) P.C.B.

I JMAIN (1) P.C.B.

I

I

HFig. 8

14


I SELF DIAGNOSIS FUNCTION (DIAG)RX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

There are 18 DIAG menu items, each of which has sub-menu items. Listed in the table below are menu items and sub-menu items. (Some diagnostic functions do not apply to all models or to all markets.) No DIAG menu 1 YSS938 sub-menu 1. ANALOG BYPASS 2. YSS 0dB 3. YSS FULL BIT 1. YSS-CS 0dB 2. YSS-CS FULL BIT 1. CS-YSS 0dB 2. CS-YSS FULL BIT 1. CS49329 0dB 2. CS49329 FULL BIT 1. HP 0dB 2. HP FULL BIT 1. RAM 0dB 2. MAIN ATT 1. PRO LOGIC I 2. PRO LOGIC II 3. NEO: 6 1. MAIN: SMALL 0dB 2. MAIN: LARGE -10dB 3. CENTER: NONE 4. LFE/BASS: MAIN 5. FRONT MIX: 5ch 6. REAR C: MUTE 7. REAR L/R: MUTE 1. VFD CHECK (Initial display) 2. VFD DISP OFF (All segments OFF) 3. VFD DISP ALL (All segments ON 100%) 4. VFD DIMMER (All segments ON 50%) 5. CHECKED PATTERN (ON in lattice) 1. TEST ALL 2. TEST MAIN L 3. TEST CENTER 4. TEST MAIN R 5. TEST REAR R 6. TEST REAR CENTER 7. TEST REAR L 8. TEST LFE 1. TX DATA 2. HARD FLOW 1. PRESET INHIBIT (memory initialization inhibited) 2. PRESET RESERVED (memory initialized) 1. DC/PS (protection) 2. THM/FAN OUT 3. REC-OUT 4. IMP SW/POWER LIMIT 5. K0/K1 (panel key) 6. FAN DRIVE TEST: HIGH (Fan test only applies to models with a fan.) 7. FAN DRIVE TEST: MID (Fan test only applies to models with a fan.) 8. FAN DRIVE TEST: LOW (Fan test only applies to models with a fan.)

2 3 4 5 6 7

YSS-CS CS-YSS CS49329 HP ROUTE RAM THROUGH DOLBY PRO LOGIC SPEAKER SET

8

9

EFFECT OFF/ DISPLAY CHECK

10 MANUAL TEST

11 RS-232C 12 FACTORY PRESET 13 AD DATA CHECK /FAN TEST

15


No DIAG menu 14 IF STATUS

15 DSP RAM CHECK 16 CS DL CODE

17 SOFT SW

18 ROM VERSION/CHECK SUM/ PORT

sub-menu 1. IS 1 2. IS 2 3. IS 3 4. CS 1 5. CS 2 6. CS 3 7. CS 4 8. CS 5 9. BY1 10. BY2 11. BY3 12. BY4 13. BC1 14. BC2 15. BC3 16. BC4 17. BC5 18. YS1 19. YS2 20. YS3 21. CS 22. MTT 1. YSS938 BUS CHECK 2. PLD/SRAM BUS CHECK 1. ROM DATA VERSION 2. TOC AREA 0 3. TOC AREA 1 4. TOC AREA 2 5. TOC AREA 3 6. TOC AREA 4 7. TOC AREA 5 8. SUM CHECK AREA 0 9. SUM CHECK AREA 1 10. SUM CHECK AREA 2 11. SUM CHECK AREA 3 12. SUM CHECK AREA 4 13. SUM CHECK AREA 5 1. SW MODE 2. MODEL SETTING 3. TUNER DESTINATION 4. TUNER EXIST 5. RDS EXIST 6. ZONE 2 EXIST 7. VIDEO FORMAT 1. VERSION 2. SUM ALL/PROGRAM 3. SUM 232C/MAKER 4. PORT 5. AAC PORT


16


Starting DIAGRX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

Press the STANDBY/ON key while pressing those two keys indicated in the figure on the right.

Keys of main unitA/B/C/D/E PRESET/ TUNING

Starting DIAG in the protection cancel modeIf the protection function works and causes hindrance to trouble diagnosis, cancel the protection function as described below, and it will be possible to enter the DIAG mode. (The protection functions other than the excess current detect function will be cancelled.) Press the STANDBY/ON key while pressing those two keys indicated in the figure on the right. At this time, keep pressing those two keys for 3 seconds or longer. In this mode, the SLEEP segment of the FL display of the main unit flashes to indicate that the mode is DIAG mode with the protection functions cancelled.Turn on the power while pressing these keys.

CAUTION!Using this product with the protection function disabled may cause damage to itself. Use special care for this point when using this mode.

Canceling DIAG[1] Before canceling DIAG, execute setting for PRESET of DIAG menu No.12 (Memory initialization inhibited or Memory initialized). * In order to keep the user memory stored, be sure to select PRESET INHI (Memory initialization inhibited). [2] Turn off the power by pressing the STANDBY/ON key of the main unit or the STANDBY key of the remote controller. DIAGNOSTIC MENU 1.DSP THR 10.MAN LTEST 2.YSS-CS 11.RS232C 3.CS-YSS 12.PRESET 4.CS49329 13.AD/FAN 5.HP ROUTE 14.STATUS 6.RAM THR 15.DSP RAM 7.PRO LOGIC 16.CS DL COD 8.SP SET 17.SOFT SW 9.VFD CHECK 18.VER/SUM/P

Display provided when DIAG startedWhen the monitor is connected, DIAGNOSTIC MENU appears on its screen as shown in the figure. (It remains on display until DIAG is cancelled.)

The FL display of the main unit displays the protection function history data and the version (1 alphabet) and the DIAG menu (sub-menu (ANALOG BYPASS) of DIAG menu No.1 YSS938) a few seconds later.

When there is no history of protection function:Opening messageWhen there is no history of protection function

DIAG menu display

Version (1 alphabet) After a few seconds

When there is a history of protection function:When there is a history of protection function due to excess current Version (1 alphabet)

Cause: An excessive current flowed through the power amplifier. Supplementary information: As current of the power transistor is detected, the abnormal channel can be identified by checking the current detect transistor. Turning on the power without correcting the abnormality will cause the protection function to work immediately and the power supply will instantly be shut off.

17


When there is a history of protection function due to abnormal voltage in the power supply section

Version (1 alphabet)

Cause: The voltage in the power supply section is abnormal. Supplementary information: The abnormal voltage is displayed in % based on 5V as 100%. Turning on the power without correcting the abnormality will cause the protection function to work 1 second later and the power supply will be shut off.


Voltage display in %When there is a history of protection function due to abnormal DC output


Cause: DC output of the power amplifier is abnormal. Supplementary information: The abnormal voltage is displayed in % based on 5V as 100%. Turning on the power without correcting the abnormality will cause the protection function to work 3 seconds later and the power supply will be shut off.

Voltage display in %

When there is a history of protection function due to excessive heat sink temperature


Cause: The temperature of the heat sink is excessive. Supplementary information: The abnormal voltage is displayed in % based on 5V as 500%. Turning on the power without correcting the abnormality will cause the protection function to work 1 second later and the power supply will be shut off.

Voltage display in %

* Additional causes of protection can be due to loose connections, associated components, CPU, etc. * For the protection voltage value, refer to DIAG menu No.10 described later.

History of protection functionWhen the protection function has worked, its history is stored in memory with a backup. Even if no abnormality is noted while servicing the unit, an abnormality which has occurred previously can be defined as long as the backup data has been stored. The history of the protection function is cleared when DIAG is cancelled by selecting PRESET RESERVED (Memory initialized) of DIAG menu No.10 or when the backup data is erased.

Display during menu operationDuring the DIAG operation, the menu list described in the section of the startup screen appears on the superimposed screen and the function at work is indicated on the FL indicator. The contents displayed during the function operation are described in the later section on details of functions.

Operation procedure of DIAG menu and SUB-MENUThere are 18 MENU items, each of which has some SUB-MENU items.

PRESET/ TUNING

DIAG menu selectionMain unit: Select the menu using (Forward) and (Reverse) keys of PRESET/ TUNING located in the sealing panel. Remote control unit: Select the menu using (Forward) and (Reverse) keys.

DIAG menu selectionPROGRAM

SUB-MENU selection

SUB-MENU selectionMain unit: Select the sub-menu using (Forward) and (Reverse) keys of PROGRAM located in the sealing panel. Remote control unit: Select the sub-menu using (Forward) and (Reverse) keys.Use these keys for DIAG menu selection.

Use these keys for SUB-MENU selection.

18


Functions in DIAG modeRX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

In addition to the DIAG menu items, functions as listed below are available. Input selection, 6CH input Center/Rear/Rear Center/Sub-woofer level adjustment Muting Speaker relay A/B Power on/off Master volume * Functions related to the tuner and the set menu are not available. * It is possible to confirm Menu No.14 IF STATUS while keeping the signal process (operation status) of each DIAG menu by using the input mode key of the main unit.

Initial settings used to start DIAGThe following initial settings are used when starting DIAG. When DIAG is canceled, these settings are restored to those before starting DIAG. Master volume: -40dB Input: DVD (6CH INPUT OFF) Effect level: 0dB Audio mute: OFF Speaker relay A/B: ON Speaker setting: LARGE / BASS OUT = BOTH DIAG menu: YSS938 (1. ANALOG BYPASS)

19


Details of DIAG menuWith full-bit output specified in some modes, it is possible to execute 0dBFS output without head margin in each channel.RX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

1. YSS938This function is for YSS938 only. Main DSP of YSS938 is selected for MAIN L/R output. Using the sub-menu, it is possible to select the analog bypass, 0dB output level or full-bit output. ANALOG BYPASS The signal is output through the signal path as shown below. The signal for L/R is output as it is without passing through the DSP section. Reference data (PRE OUT) INPUT: DVD ANALOG SWFR: 50Hz, Others: 1kHz Condition MAIN L/R CENTER REAR C Both ch, -20 dBV, volume -10 dB -5.5 dBV -5.5 dBV -5.5 dBV SWFR -2.5 dBV RL/RR -5.5 dBV

CS49329

L/R AnalogA/D

DIR

DigitalYSS938

Main DSP DD/dts

Sub DSP Through

C RC/SW FL/FR RL/RR

20


YSS 0dB The signal is output including the head margin. Head margin: Main L/R: 0dBFS, Center: -6dBFS, Rear Center: -3dBFS, FL/FR: -6dBFS, RL/RR: -12dBFS, SWFR: Add L/R signal at -20dBFS. Reference data (PRE OUT) INPUT: DVD ANALOG SWFR: 50Hz, Others: 1kHz Condition MAIN L/R CENTER -5.5 dBV REAR C -5.5 dBV SWFR -2.5 dBV RL/RR -5.5 dBV Both ch, -20 dBV, volume -10 dB -5.5 dBV


YSS FULL BIT The signal is output in digital full bit without including the head margin. Reference data (PRE OUT) INPUT: DVD ANALOG SWFR: 50Hz, Others: 1kHz Condition MAIN L/R CENTER REAR C SWFR RL/RR Both ch, -20 dBV, volume -10 dB -5.5 dBV +0.5 dBV -3.0 dBV -2.5 dBV +6.5 dBV

DSP THROUGH ~ YSS (Analog)CS49329

L/R

L/R C RC/SW FL/FR RL/RR

Analog

A/DL/-

DIR

DigitalYSS938

Main DSP Through

Sub DSP Through

R/L+R L/R L/R

DSP THROUGH ~ YSS (DD/dts (ES off))CS49329

L/R AnalogA/D

DIR

DigitalYSS938

Main DSP DD/dts

Sub DSP Through

C RC/SW FL/FR RL/RR

21


2. YSS-CS8 channels are made usable by CS49329. The signal enters YSS938 through the Sub DSP passage and then undergoes through-output. CS49329 is selected for the Main L/R output. Using the sub-menu, it is possible to select full bit output at 0dB output level. YSS-CS 0dB The signal is output including the head margin. Head margin: Main L/R: -18dBF, Center: -6dBFS, Rear Center: -3dBFS, FL/FR: -6dBFS, RL/RR: -18dBFS, SWFR: Add L/R signal at -20dBFS. Reference data (PRE OUT) INPUT: DVD ANALOG SWFR: 50Hz, Others: 1kHz Condition MAIN L/R CENTER -5.5 dBV REAR C -5.5 dBV SWFR -2.5 dBV RL/RR -5.5 dBV Both ch, -20 dBV, volume -10 dB -5.5 dBVRX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

YSS-CS FULL BIT The signal is output in digital full bit without including the head margin. Reference data (PRE OUT) INPUT: DVD ANALOG SWFR: 50Hz, Others: 1kHz Condition MAIN L/R CENTER REAR C Both ch, -20 dBV, volume -10 dB -5.5 dBV +0.5 dBV -3.0 dBV SWFR RL/RR -2.5 dBV +6.5 dBV

DSP THROUGH ~ YSS-CS (Analog)CS49329 Through

L/R AnalogA/DDIR

Digital YSS938

Main DSP Through

Sub DSP Through

C RC/SW FL/FR RL/RR

DSP THROUGH ~ YSS-CS (DD/dts (ES off))CS49329 Through

L/R AnalogA/D

DIR

Digital YSS938

Main D SP DD/dts

Sub D SP Through

C RC/SW FL/FR RL/RR

22


3. CS-YSSRX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

8 channels are made usable by CS49329. The signal enters YSS938 through the Sub DSP passage and then undergoes through-output. YSS938 Main DSP is selected for the Main L/R output. Using the sub-menu, it is possible to select full bit output at 0dB output level. CS-YSS 0dB The signal is output including the head margin. Head margin: Main L/R: -18dBFS, Center: -6dBFS, Rear Center: -3dBFS, FL/FR: -6dBFS, RL/RR: -18dBFS, SWFR: Add L/R signal at -20dBFS. Reference data (PRE OUT) INPUT: DVD ANALOG SWFR: 50Hz, Others: 1kHz Condition MAIN L/R CENTER REAR C Both ch, -20 dBV, volume -10 dB -5.5 dBV -5.5 dBV -5.5 dBV SWFR -2.5 dBV RL/RR -5.5 dBV

CS-YSS FULL BIT The signal is output in digital full bit without including the head margin. Reference data (PRE OUT) INPUT: DVD ANALOG SWFR: 50Hz, Others: 1kHz Condition MAIN L/R CENTER REAR C Both ch, -20 dBV, volume -10 dB -5.5 dBV +0.5 dBV -3.0 dBV SWFR RL/RR -2.5 dBV +6.5 dBV

DSP THROUGH ~ CS-YSS (Analog) (Use of CS-YSS is not available due to restriction of the passage.)

CS49329 Through

L/R AnalogA/DDIR

Digital YSS938

Main DSP Through

Sub DSP Through

C RC/SW FL/FR RL/RR

DSP THROUGH ~ CS-YSS (AAC/dts (ES off))CS49329 dts/AAC

L/R AnalogA/D

DIR

Digital YSS93823

Main DSP Through

Sub DSP Through

C RC/SW FL/FR RL/RR


4. CS493298 channels are made usable by CS49329. The signal enters YSS938 through the Sub DSP passage and then undergoes through-output. CS49329 is selected for the Main L/R output. Using the sub-menu, it is possible to select full bit output at 0dB output level. * As a 3dB margin of CS is always effective for RC when decoding dts ES, even when the output in full bit is specified, the RC output remains up to 0dBFS when 0dBFS is input to LS/RS. CS49329 0dB The signal is output including the head margin. Head margin: Main L/R: -18dBFS, Center: -6dBFS, Rear Center: -3dBFS, FL/FR: -6dBFS, RL/RR: -18dBFS, SWFR: Add L/R signal at -20dBFS. Reference data (PRE OUT) INPUT: DVD ANALOG SWFR: 50Hz, Others: 1kHz Condition MAIN L/R CENTER REAR C Both ch, -20 dBV, volume -10 dB -5.5 dBV -5.5 dBV -5.5 dBV SWFR -2.5 dBV RL/RR -5.5 dBVRX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

CS49329 FULL BIT The signal is output in digital full bit without including the head margin. Reference data (PRE OUT) INPUT: DVD ANALOG SWFR: 50Hz, Others: 1kHz Condition MAIN L/R CENTER REAR C SWFR RL/RR Both ch, -20 dBV, volume -10 dB -5.5 dBV +0.5 dBV -3.0 dBV -2.5 dBV +6.5 dBV

DSP THROUGH ~ CS (Analog) (Use of CS only is not available due to restriction of the passage.)

CS49329 Through

L/R


Analog

A/DL/-

DIR

Digital YSS938DSP THROUGH ~ CS (PCM)

Main DSP Through

Sub DSP Through

R/L+R L/R L/R

CS49329 Through

L/R

L/R C RC/SW FL/FR RL/RR24

Analog

A/DL/-

DIR

Main DSP

Digital YSS938

Sub DSP Through

R/L+R L/R L/R


DSP THROUGH ~ CS (AAC/dts (ES auto))RX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

CS49329 dts/AAC

L/R


Analog

A/DC/-

DIR

Main DSP

Digital YSS938

Sub DSP Through

RC/SW L/R RL/RR

5. HP ROUTEThis function is for YSS938 only. Sub DSP SDOB3 of YSS938 is selected for MAIN L/R output. Using the sub-menu, it is possible to select the full-bit output at 0dB output level. HP 0dB The signal is output including the head margin. Head margin: Main L/R: -18dBFS, Center: -6dBFS, Rear Center: -3dBFS, FL/FR: -6dBFS, RL/RR: -18dBFS, SWFR: Add L/R signal at -20dBFS. Reference data (PRE OUT) INPUT: DVD ANALOG SWFR: 50Hz, Others: 1kHz Condition MAIN L/R CENTER - REAR C - SWFR - RL/RR - Both ch, -20 dBV, volume -10 dB -5.5 dBV

HP FULL BIT The signal is output in digital full bit without including the head margin.

Reference data (PRE OUT) INPUT: DVD ANALOG SWFR: 50Hz, Others: 1kHz Condition MAIN L/R CENTER - REAR C - SWFR - RL/RR - Both ch, -20 dBV, volume -20 dB +2.5 dBV

DSP THROUGH ~ HP ROUTE (Auto)CS49329

L/R AnalogA/D DIR Main DSP Thr/DD/dts Sub DSP Through

DigitalYSS938

C RC/SW FL/FR RL/RR

25


6. RAM THROUGHThis function is for YSS938 only. Main L/R signal is output through Main DSP of YSS938. CT/RC, RL/RR and FL/FR signals are output through Sub DSP - DRAM. Using the sub-menu, it is possible to select the full-bit output at 0dB output level. RAM 0dBRX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

Reference data (PRE OUT) INPUT: DVD ANALOG SWFR: 50Hz, Others: 1kHz Condition MAIN L/R CENTER REAR C Both ch, -20 dBV, volume -10 dB -5.5 dBV -5.5 dBV -5.5 dBV SWFR -2.5 dBV RL/RR -5.5 dBV

MAIN ATT MAIN -9dB

Reference data (PRE OUT) INPUT: DVD ANALOG SWFR: 50Hz, Others: 1kHz Condition MAIN L/R CENTER REAR C Both ch, -20 dBV, volume -10 dB -14.5 dBV -5.5 dBV -5.5 dBV SWFR -2.5 dBV RL/RR -5.5 dBV

RAM THROUGH ~ (Auto)CS4932X

L/R

Analog

A/D DIR Main DSP Thr/DD/dts Sub DSP ThroughC RC/SW FL/FR RL/RR

DigitalYSS938

4Mbit DRAM

26


7. DOLBY PRO LOGIC [YSS938]RX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

PRO LOGIC I

Reference data (PRE OUT) INPUT: DVD ANALOG SWFR: 50Hz, Others: 1kHz Condition Each ch, -20 dBV, volume -10 dB Both ch, -20 dBV, volume -10 dB Both ch, -20 dBV (reverse phase), volume -10 dB MAIN L/R CENTER -5.5 dBV - - - -2.5 dBV - REAR C - - - SWFR - - - RL/RR - - -5.5 dBV

PRO LOGIC II


The L/C/R/RL/RR signals undergo the Pro-Logic processing and C/RL/RR signals are output through Sub DSP-DRAM. Main DSP is selected for MAIN L/R output. Using the sub-menu, it is possible to select PRO LOGIC I, II (Movie). The Auto Input Balance function is always off. When dts/AAC input is used, the signal is decoded by CS49329 and the L/R signal undergoes the Pro-Logic processing. When the Dolby Digital Multi input is used, the function is the same as in the Dolby Digital Normal mode. The LFE signal is not output when decoding in the PRO LOGIC I, II mode.

Dolby Pro Logic (Auto)CS49329 dts/AAC

L/R

Analog

A/D

DIR

DigitalYSS938

Main DSP Pro Logic I/II or DD

Sub DSP Through

C RC/SW FL/FR RL/RR

4Mbit DRAM

27


Neo:6



L/C/R/RL/RC/RR signals are NEO:6 processed by CS49329 and C/RL/RC/RR signals are output through Sub DSPDRAM. CS49329 is selected for the MAIN L/R output. The NEO:6 mode is fixed to Cinema 6ch. When DD/dts input is used, the signal is decoded by YSS-938 and then L/R signal is NEO:6 processed by CS49329. When AAC input is used, the signal is muted. When NEO:6 decoding is used, the LFE signal is not output.

NEO:6 (Auto)CS49329 NEO:6

L/R

Analog

A/DDIR

Digital YSS938

Main DSP DD/dts/Thr

Sub DSP Through

C RC/SW FL/FR RL/RR

4Mbit DRAM

28


8. SPEAKERS SETRX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

The input signal is automatically identified in the order of dts DOLBY DIGITAL AAC PCM Analog. There are seven sub-menu items as follows. The signals output from the DSP block are the same as 1. YSS938: YSS 0dB.

MAIN: SMALL 0dB

MAIN: LARGE -10dB

CENTER: NONE

LFE: BASS:MAIN

Front Mix: 5ch

REAR CENTER: MUTE

REAR L/R: MUTE

The analog switch settings for each sub-menu are as shown in the table below. Sub-menu MAIN: SMALL 0dB MAIN: LARGE -10dB CENTER: NONE LFE/BASS: MAIN FRONT MIX: 5CH REAR CENTER: MUTE REAR L/R: MUTE CENTER SP REAR SP LARGE LARGE LARGE NONE SMALL LARGE LARGE LARGE LARGE LARGE SMALL LARGE LARGE LARGE MAIN SP SMALL LARGE LARGE LARGE LARGE LARGE LARGE MAIN LEVEL LFE/BASS 0dB SWFR -10dB 0dB 0dB 0dB 0dB 0dB BOTH BOTH MAIN BOTH BOTH BOTH

1 2 3 4 5 6 7

LARGE: SMALL: NONE:

This mode is used with a speaker with high bass reproduction performance (a large unit). Full bandwidth signals are output. This mode is used with a speaker with low bass reproduction performance (a small unit). The signals of 90Hz or less are mixed into the channel specified by LFE/BASS. This mode is used with no center speaker. The center content is reduced by 3dB and distributed to MAIN L/R.

Reference data (PRE OUT) INPUT: DVD ANALOG (Both ch) VOLUME: -10 dB 1 2 3 4 5 6 7 Sub-menu MAIN: SMALL 0dB MAIN: LARGE -10dB CENTER: NONE LFE/BASS: MAIN FRONT MIX: 5CH REAR CENTER: MUTE REAR L/R: MUTE Condition 1kHz/90Hz, -20 dBV 1kHz, -20 dBV 1kHz, -20 dBV 50Hz, -20 dBV 1kHz, -20 dBV 1kHz, -20 dBV 1kHz, -20 dBV MAIN L/R CENTER REAR C -5.5/-8.5 dBV -5.5 dBV -5.5 dBV -15.5 dBV -5.5 dBV -9.0 dBV - -5.5 dBV -5.5 dBV SWFR -2.5 dBV -2.5 dBV -2.5 dBV RL/RR -5.5 dBV -5.5 dBV -5.5 dBV

-4.0 dBV -8.5 dBV (90Hz) -5.5 dBV -11.5 dBV -5.5 dBV -5.5 dBV -5.5 dBV -5.5 dBV -5.5 dBV -5.5 dBV - -5.5 dBV

- -8.5 dBV (90Hz) -2.5 dBV -5.5 dBV -2.5 dBV -2.5 dBV -5.5 dBV -

29


9. DISPLAY CHECKThis program is used to check the FL display section. The display condition varies as shown below according to the submenu operation. The signals are processed using EFFECT OFF (The L/R signal is output using ANALOG MAIN BYPASS.) The video signal internal/external synchronization switching is controlled by the microprocessor. When the initial message is displayed and all the FL segments light up, it is switched to the internal synchronization but other than that it is forced to the external synchronization setting. Also, except for the initial display, 128 pictographs for checking the OSD driver are used for the video signal output display.RX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

Initial display

All segments OFF

All segments ON (dimmer 100%)

Lighting in lattice

Lighting of segments in lattice

All segments ON (dimmer 50%)

Short

Normal

Segment conditions of the FL driver and the FL tube are checked by turning ON and OFF all segments. Next, the operation of the FL driver is checked by using the dimmer control. Then a short between segments next to each other is checked by turning ON and OFF all segments alternately (in lattice). (In the above example, the segments in the second row from the top are shorted.)

10. MANUAL TESTThe noise generator with a built-in DSP outputs the test noise through the channels specified by the sub-menu. The noise frequency for LFE is 35 to 250 Hz. Other than that, the center frequency is 800Hz.

TEST ALL

TEST MAIN L

TEST CENTER

Noise is output from all channels.

Noise is output from the MAIN L channel.

Noise is output from the CENTER channel. TEST REAR CENTER

TEST MAIN R

TEST REAR R

Noise is output from the MAIN R channel.

Noise is output from the REAR R channel.

Noise is output from the REAR C channel.

TEST REAR L

TEST LFE

Noise is output from the REAR L channel.

Noise is output from the SUB WOOFER channel.

30


11. RS-232CThis menu is unused.RX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

12. FACTORY PRESETThis menu is used to reserve and inhibit initialization of the back-up RAM. The signals are processed using EFFECT OFF. (The L/R signal is output using ANALOG MAIN BYPASS.) PRESET INHIBIT (Initialization inhibited) RAM initialization is not executed. Select this sub-menu to protect the values set by the user. PRESET RESERVED (Initialization reserved) Initialization of the back-up RAM is reserved. (Actually, initialization is executed the next time that the power is turned on.) Select this sub-menu to reset to the original factory settings or to reset the RAM.

CAUTION: Before setting to the PRESET RESERVED, write down the existing preset memory content of the Tuner in a table as shown below. (This is because setting to the PRESET RESERVED will cause the user memory content to be erased.)Preset group A B C D E P1 P2 P3 P4 P5 P6 P7 P8

PRESET STATIONSSTATION PAGE NO. 1 2 3 A/C/E 4 5 6 7 8 FM FACTORY PRESET DATA (MHz) U, C R, T, K, A, B, G 87.5 90.1 95.1 98.1 107.9 88.1 106.1 107.9 87.5 90.1 95.1 98.1 108.0 88.1 106.1 108.0 B/D STATION PAGE NO. 1 2 3 4 5 6 7 8 AM FACTORY PRESET DATA (kHz) U, C, R, T, K A, B, G 630 1080 1440 530 1710 900 1350 1400 630 1080 1440 531 1611 900 1350 1404

13. AD DATA CHECK/FAN TESTThis menu is used to display the A/D conversion value of the main CPU which detects panel keys of the main unit and protection functions in % using the sub-menu. (Reference voltage 5V as 100%) During signal processing, the condition before execution is maintained. When K0/K1 menu is selected, keys become non-operable due to detection of the values of all keys. However, it is possible to advance to the next sub-menu by turning the VOLUME of the main unit. When using this function, note that turning the VOLUME more than 1 click would cause the volume value to change. * The figures in the diagram are given as reference only. DC/PS (protection detection) DC: DC detect protection value (Normal value: 1 to 13) PS: Power supply voltage protection value (Normal value: 21 to 31) * If DC or PS is out of the normal value range, the protection function works to turn off the power. 31


THM/FAN OUT (temperature detection/fan drive level) THM: 500% display of the voltage based on the temperature detected value. Reference voltage : 5V (Normal value: U, C models ..... 51 to 169 Others models ..... 41 to 151) Fan: Current fan drive level on the left and the past fan drive history on the right. REC-OUT (Select position) This applies to the model equipped with the REC OUT selector. [Table 1]Display 0+2 152 302 442 602 762 922 1222 1372 1532 1702 1862 2022 REC OUT Select CD-R CBL/SAT PHONO V-AUX MD/TAPE D-TV/LD PHONO TUNER VCR1 CD VCR2/DVR SOURCE DVD


IMP SW/POWER LIMIT (Impedance/power limiter detection) IMP: 8 or 4 ohm impedance switch setting PL: Power limiter detection value K0/K1 (Panel key of main unit) [Remote control code: ] A/D of the key fails to function properly when the standard value is deviated by 4%. In this case, check the constant of partial pressure resistor, solder condition, etc. Refer to table 2. [Table 2]Display 00+2 102 202 302 402 502 602 702 802 902 100 K0 PRESET/TUNING PRESET/TUNING PRESET/TUNING FM/AM MEMORY TUNING MODE RDS MODE RDS EON PTY MODE PTY START KEY OFF K1 INPUT INPUT INPUT MODE SPEAKERS A SPEAKERS B EFFECT PROGRAM PROGRAM A/B/C/D/E KEY OFF

FAN DRIVE TEST (For models so equipped) HIGH

FAN DRIVE TEST (For models so equipped) MID

FAN DRIVE TEST (For models so equipped) LOW

32


14. IF STATUS (Input function status)RX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

Using the sub-menu, the status data is displayed one after another in the hexadecimal notation. During signal processing, the status before execution of this menu is maintained. * Numeric values in the figure example are for reference. IS1-3 (Internal status) Indicates the status information of the microprocessor.

5th byte 4th byte 3rd byte 2nd byte 1st byte Digital input/output setting value Upper 4 bits: REC OUT selected/lower 4 bits: INPUT selectedNumeric value 0 1 2 3 Selection NONE OPT A (V-AUX) OPT B (CD) OPT C (CD-R) Numeric value 4 6 8 9 Selection OPT D (DVD) OPT F (D-TV/LD) COAX A (CD) COAX B (CBL/SAT)

Fs information of reproduction signalDisplay Fs (kHz) 00 Analog 01 32 02 44.1 03 48 04 64 05 88.2 06 96 0A Unknown NRM 0B Unknown DBL 0C Unknown QUAD 0D Not defined

Audio code mode information of reproduction signalDisplay Audio Code 00 01 02 1/0 03 2/0 04 3/0 05 2/1 06 3/1 07 2/2 08 3/2 09 2/3 0A 3/3 0B 0C 0D Unknown MULTI MONO 1+1 OVER 6.1 MULTI PCE

Format information of reproduction signal *1: Analog processing used for digital reproduction is not possible because of a commercial bit or 4-ch audio reason.Display 00 01 10 20 21 22 23 50 51 54 58 5C 60 C0 C1 C4 Signal format Analog (Unlock) Incorrect digital (*1) PCM Audio Digital Data IEC1937 Data None PCM Unknown dts Red dts dts-ES MATRIX dts-ES DISCRETE dts-ES (Both flag) AAC Dolby Digital D.D. Karaoke D.D.6.1 (D.D.EX)

Signal processing status information *2: With digital signals other than 32kHz, 44.1kHz and 48kHz, through processing method is used for reproducible signals.bit7 bit6 bit5 bit4 MUTE request bit3

Red dts flashing bit2 Through & bypass (*2) 6.1ch. field being processed bit1 FULL MUTE (ON: 1) bit0 dts analog mute

33


CS1-5: Indicates channel status information of the input signal (IEC60958).


BY1-4: Indicates information of the bit stream included in the DOLBY DIGITAL signal.

BC1-4: Indicates information of the bit stream included in the dts signal.

YS1-3: Indicates device status information of YSS938 (IC514). * The numeric value in the figure is an example for reference.

Byte No. 1 2 3 4 5

Function YSS MUTE Reg YSS MODE Reg YSS IPORT BIT 7-0 YSS IPORT BIT 14-8 YSS OPORT

Byte No. 1 2 3 4 5

Function IEC 1937 Preamble Pc Data Stream Reg Status Reg YSS ZERO Reg MIREG

Byte No. 1 2 3 4

Function DIR Status DIR fs DIR fs count YSS ZEROBF

CS: CS49329 Unsolicited Messages (AUTODETECT_RESPONSE)

MTT: Mute Trigger

Byte No. 1 2 3 4 5

Function Mute condition Factor of the last mute Error count of YSS938-FSCNT Mute count by YSS938-FSCNT Error factor of down load of CS49329

15. DSP RAM CHECKThis menu is used to self-diagnose whether or not the bus connection for the YSS938 and the external RAM is made properly. During signal processing, the status before execution of this menu is maintained. The address bus and the data bus are checked and the connection condition is displayed. When no error is detected, "NoEr" appears on display. YSS938 Bus CheckDisplay WAIT NoEr DATA RSCS ADDR Description Bus is being checked. No error detected. Data bus shorted or open. /RAS or /CAS shorted, or open. Address bus shorted or open.

34


PLD/SRAM BUS CHECKDisplay WAIT NoEr DATA ADDR Description Bus is being checked. No error detected. Data bus shorted or open. (XX: 00-07) Address bus shorted or open. (XX: 00-0E)


16. CS DL CODEThis menu is used to display the data version, TOC information and sum calculated value of the flash ROM for CS49329. ROM DATA VERSION: Displays the data version of the Flash ROM for CS49329.

TOC AREA 0-5: Displays the TOC information.

SUM CHECK AREA 0-5: Displays the sum calculated value.

17. SOFT SWThis menu is used to switch the function settings on P.C.B. through the software so as to activate the product. The protection function follows the P.C.B. settings. When connected to AC or in the maker preset state, the unit is initialized to the P.C. B. setting. Display of each function after initialization varies depending on settings on P.C.B. The operation mode can be changed by selecting the sub-menu and then using the EFFECT key. With SOF selected for the SW mode, the settings become effective. SW MODE: PCB or SOFT can be selected.

MODEL SETTING: V1200, V2200, V3200 or AX3200 can be selected.

TUNER DESTINATION: J, UC, ATKG or R can be selected.

TUNER EXIST: NOT or EXIST can be selected.

RDS EXIST: NOT or EXIST can be selected.

ZONE 2 EXIST: NOT or EXIST can be selected.

VIDEO FORMAT: NTSC or PAL can be selected.

35


18. MICROPROCESSOR INFORMATIONThe version, checksum and the port specified by the microprocessor are displayed. The signal is processed using EFFECT OFF. The checksum is obtained by adding the data at every 16 bits for each program area and expressing the result as a 4-figure hexadecimal data. Version Release 1 figure / Main 2 figures / DSP 2 figures / Communication 1 figure / Boot manufacturer 1 figure / Boot 232c 1 figure Checksum A : All P : Program area Checksum 2 : Boot 232CRX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

M : Boot manufacturer

Check of port setting for judging microprocessor function

Display of AAC function detection port state

PORT:0 0 0 0 0 0 0 0 bit 7 6 5 4 3 2 1 0 Model type 0 (*1) Model type 1 (*1) Tuner mode 0 (*2) Tuner mode 1 (*2) Tuner with (1) / without (0) RDS with (1) / without (0) ZONE2 with (1) / without (0) VIDEO format: PAL (1) / NTSC (0) *2 (Tuner mode)Tuner mode 0 0 0 1 1 Tuner mode 1 0 1 0 1

*1 (Model type)Type o Type 1 0 0 1 0 0 1 1 1 Model type V1200 V2200 V3200 AX3200

Tuner frequency AM: 531-1611kHz/9kHz FM: 76.0-90.0MHz/100kHz AM: 531-1611kHz/9kHz FM: 87.5-108.0MHz/50kHz AM: 530-1710kHz/10kHz FM: 87.5-107.9MHz/200kHz R destination, Port6: LOW AM: 530-1710kHz/10kHz FM: 87.5-108.0MHz/100kHz HIGH AM: 531-1611kHz/9kHz FM: 87.5-108.0MHz/50kHz

I AMP ADJUSTMENTConfirmation of Idling Current of Main (1) P. C. B. Right after power is turned on, confirm that the voltage across the terminals of R64 (Main Lch), R65 (Main Rch), R61 (Center), R59 (Rear Lch), R60 (Rear Rch), R126 (Rear Cch) are between 0.1mV and 10.0mV. If it exceeds 10.0mV, open (cutoff) R39 (Main Lch), R40 (Main Rch), R37 (Center), R34 (Rear Lch), R35 (Rear Rch), R117 (Rear Cch) and reconfirm the voltage. Confirm that the voltage is 0.20mV ~ 15.0mV after 60 minutes.R39 (MAIN Lch) R40 (MAIN Rch) R37 (CENTER) R34 (REAR Lch) R35 (REAR Rch) R117 (REAR Cch) 0.1mV ~ 10.0mV (DC) 0.1mV ~ 10.0mV (DC)

R64 (MAIN Lch) R65 (MAIN Rch) R61 (CENTER)

Cut off R59 (REAR Lch) R60 (REAR Rch) R126 (REAR Cch)

36


I DISPLAY DATARX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

G V901 : 16-BT-91GK (V7683200)

y

1

PATTERN AREA

G PIN CONNECTION Pin No. 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33

Connection F2 F2 NPNP P37 P36 P35 P34 P33 P32 P31 P30 P29 P28 P27 P26 P25 P24 P23 P22 P21 P20 P19 P18 P17 P16 P15 P14 P13 P12 P11 P10 P9 Pin No. 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

Connection P8 P7 P6 P5 P4 P3 P2 P1 NC NC NC NC 16G 15G 14G 13G 12G 11G 10G 9G 8G 7G 6G 5G 4G 3G 2G 1G NP NP F1 F1Note : 1) F1, F2 ..... Filament 4) DL ..... Datum Line 2) NP ..... No pin 3) NC ..... No connection (NC pin should be electrically open on the PC board.) 5) 1G ~ 16G ..... Grid 6) Field of vision is a minimum of 29 from the lower side.

G GRID ASSIGNMENT16G 15G

1G

2G

3G

4G

5G

6G

7G

8G

9G 10G 11G 12G 13G

14G

1-1

2-1

3-1

4-1

5-1

1-2

2-2

3-2

4-2

5-2 B9 B8 B7 B6 B5 B4 B3 B2 B1

1-3

2-3

3-3

4-3

5-3

1-4

2-4

3-4

4-4

5-4

1-5

2-5

3-5

4-5

5-5

1-6

2-6

3-6

4-6

5-6 S1

1-7

2-7

3-7

4-7

5-7

(15G)

(1G~14G)

37


G ANODE CONNECTION 16G P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P26 P27 P28 P29 P30 P31 P32 P33 P34 P35 P36 P37 S1 B1 B2 B3 B4 B5 B6 B7 B8 B9 S2 15G S2 14G 1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7 5-7 13G~2G 1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7 5-7 1GRX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

1-1 2-1 3-1 4-1 5-1 1-2 2-2 3-2 4-2 5-2 1-3 2-3 3-3 4-3 5-3 1-4 2-4 3-4 4-4 5-4 1-5 2-5 3-5 4-5 5-5 1-6 2-6 3-6 4-6 5-6 1-7 2-7 3-7 4-7 5-7 T1

38


39SDOB0 SDOB1 SDOB2 SDOB3

SDWCKI1

SDBCKI1

SELOBSDOB Interface ZEROBF3R-0L

SELOA

I IC DATA

IC514 : YSS938-F DSP

SDOBCKSEL


SELB SELA

SELI0-13

END OVFB

OVFSELOVFB/END

Coefficient, Program RAMSubDSP

XO XI SELI1 SELI0 SELOA SELOB TESTMS TESTXEN IPORT0 IPORT1 IPORT2 IPORT3 IPORT4 DDIN0 DDIN1 DDIN2 DDIN3 VSS CPO AVDD DIRPCO DIRPRO AVSS TESTBRK TESTR1 TESTR2 VDD1 SDWCKI0 SDBCKI0 /SDBCKO IPORT8 IPORT9 IPORT10 IPORT11 SDIA SDOA2 SDOA1 SDOA2 SDIB3 SDIB2

External Memory Interface

RAMA0-17 RAMOEN RAMWEN RASN CASN RAMD0-15

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

SDIBCKSELSDIB Interface

MPLOAD

SDIBSEL

OPORT0-7C, LFE LS, RS L, R

SCK SDDA InterfaceDSP Clock (30 MHz)

SDIB3 SDIB2 SDIB1 SDIB0 SDOA2 SDOA1 SDOA0

SI

So PLL Main DSP(AC-3/ProLogic/DTS Decorder)

-COM Interface

Control Register

Control Signals

/cs

CPO XO XI

IPINT CRC SDIA Interface ZEROFLG NONPCM DTSDATA AC3DATA CRC MUTE KARAOKE SURNEC

IPORT8-14

IPORT0-4

YSS938-F

/SDBCKO SDIASEL SDIA DIRSDO DIRO InterfaceClock at DIR (25 MHz)

SDIACKSEL

SDWCKI0 SDBCKI0

DIRWCK DIRBCK

DIRMCK PLLVDBL

FS128 ERR BS

SYNC

DIR

CMOD6 7

C

UMOD

RAMA9 RAMA3 RAMA4 SELI9 SELI10 SELI11 SELI12 SELI13 RAMA2 RAMA5 RAMA1 RAMA6 RAMA0 RAMA7 RAMA8 VDD1 VSS RASN RAMOEN RAMWEN CASN RAMD15 RAMD14 RAMD13 RAMD12 RAMD11 RAMD10 RAMD9 RAMD8 VDD1 VSS RAMD7 RAMD6 RAMD5 RAMD4 ZEROBF0L ZEROBF0R ZEROBF1L ZEROBF1R RAMD3

IPORT5-7

U

DIRPRO DIRPCO

SDIB1 SDIB0 VSS VDD2 IPORT12 IPORT13 IPORT14 DIRSDO DIRWCK DIRBCK DIRMCK ERR/BS SYNC/U FS128/C DBL/V SDWCKI1 SDBCKI1 VSS SDOB3 SDOB2 SDOB1 SDOB0 VDD1 ZEROBF3R ZEROBF3L ZEROBF2R ZEROBF2L OPORT0 OPORT1 OPORT2 OPORT3 OPORT4 OPORT5 OPORT6 OPORT7 VSS VDD2 RAMD0 RAMD1 RAMD2

41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121

VDD2 TESTXO TESTXI SELI2 SELI3 VSS SELI4 IPINT /IC SCK SI SO /CS DIRINT /LOCK CRC SURENC VDD1 KARAOKE MUTE AC3DATA DTSDATA NONPCM VSS ZEROFLG OVFB/END RAMA17 RAMA16 RAMA15 RAMA14 RAMA13 RAMA12 SELI5 SELI6 SELI7 SELI8 VDD2 VSS RAMA11 RAMA10

120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81

DDINSEL

BSMOD

VMOD

5

DBL/V

DDIN0

DDIN1

DDIN2

DDIN3

/LOCK

DIRINT

ERR/BS

SYNC/U

FS128/C


IC514 : YSS938-F Pin DescriptionNo. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Name XO XI SELI1 SELI0 SELOA SELOB TESTMS TESTXEN IPORT0 IPORT1 IPORT2 IPORT3 IPORT4 DDIN0 DDIN1 DDIN2 DDIN3 VSS CPO AVDD DIRPCO DIRPRO AVSS TESTBRK TESTR1 TESTR2 VDD1 SDWCKI0 SDBCKI0 /SDBCK0 IPORT8 IPORT9 IPORT10 IPORT11 SDIA SDOA2 SDOA1 SDOA0 SDIB3 SDIB2 SDIB1 SDIB0 VSS VDD2 IPORT12 IPORT13 IPORT14 DIRSDO DIRWCK DIRBCK DIRMCK ERR/BS SYNC/U FS128/C DBL/V I/O O I I+ I+ O+ O+ I+ I+ I+ I+ I+ I+ I+ Is Is Is Is A A A I+ I+ I+ I+ I+ O I+ I+ I+ I+ I O O O I+ I+ I+ I+ Function Crystal oscillator connecting terminal Crystal oscillator connecting terminal (24.576MHz ) Built-in selector input 1 Built-in selector input 0 Built-in selector output A Built-in selector output B Test terminal (unconnected) Test terminal (unconnected) General purpose input terminal General purpose input terminal General purpose input terminal General purpose input terminal General purpose input terminal DIR: Digital audio interface data input terminal 0 DIR: Digital audio interface data input terminal 1/General purpose input terminal DIR: Digital audio interface data input terminal 2/General purpose input terminalRX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

(AXD) (GND) (ISEL) (RSEL)

(CXDTA) (CXDTB)

(ISEL) (Pull down) (Pull down)

I+ I+ I+ O O O O O O O O

DIR: Digital audio interface data input terminal 3/General purpose input terminal (Pull down) Ground terminal PLL filter connecting terminal +3.3V power terminal (for DIR) DIR: PLL filter connecting terminal DIR: PLL filter connecting terminal Ground terminal (for DIR) Test terminal (unconnected) PLL initialization signal input terminal for DSP (/ICD) Test terminal (unconnected) +3.3V power terminal (for terminal section) Word clock input terminal for SDIA, SDOA, SDIB,SDOB interface (Unconnected) Bit clock input terminal for SDIA, SDOA, SDIB, SDOB interface (Unconnected) DIRBCK or SDBCKI0 invert clock output terminal (Unconnected) IPINT general purpose input terminal IPINT general purpose input terminal IPINT general purpose input terminal (NONPCM) IPINT general purpose input terminal (NONPCM) AC-3/DTS bit stream (or PCM) data input terminal to Main DSP (SDIA) PCM output terminal from Main DSP (C/LFE output) (Unconnected) PCM output terminal from Main DSP (LS/RS output) (Unconnected) PCM output terminal from Main DSP (L/R output) PCM input terminal 3 to Sub DSP PCM input terminal 2 to Sub DSP PCM input terminal 1 to Sub DSP PCM input terminal 0 to Sub DSP Ground terminal +2.5V power terminal (for internal circuit) IPINT general purpose input terminal (MUTE) IPINT general purpose input terminal (DIRINT) IPINT general purpose input terminal (Unconnected) AC-3/DTS bit stream (or PCM) data output terminal from DIR DIR: Serial data word clock (fs) output terminal (WCK) DIR: Serial data bit clock (64fs) output terminal (BCK) DIR: Serial data master clock (256fs or 128fs) output terminal (MCK) DIR: Data error detect output/block start output terminal (Unconnected) DIR: Serial data synchronous timing output/user data output terminal (Unconnected) DIR: Serial data master clock 128fs output/channel status output terminal (Unconnected) DIR: Double rate clock output/validity flag output terminal (DBL)

40


No. 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110

Name SDWCKI1 SDBCKI1 VSS SDOB3 SDOB2 SDOB1 SDOB0 VDD1 ZEROBF3R ZEROBF3L ZEROBF2R ZEROBF2L OPORT0 OPORT1 OPORT2 OPORT3 OPORT4 OPORT5 OPORT6 OPORT7 VSS VDD2 RAMD0 RAMD1 RAMD2 RAMD3 ZEROBF1R ZEROBF1L ZEROBF0R ZEROBF0L RAMD4 RAMD5 RAMD6 RAMD7 VSS VDD1 RAMD8 RAMD9 RAMD10 RAMD11 RAMD12 RAMD13 RAMD14 RAMD15 CASN RAMWEN RAMOEN RASN VSS VDD1 RAMA8 RAMA7 RAMA0 RAMA6 RAMA1

I/O I+ I+ O O O O O+ O+ O+ O+ O O O O O O O O

I+/O I+/O I+/O I+/O O+ O+ O+ O+ I+/O I+/O I+/O I+/O

I+/O I+/O I+/O I+/O I+/O I+/O I+/O I+/O O O O O

Function Word clock input terminal for SDIB, SDOB interface (Unconnected) Bit clock input terminal for SDIB, SDOB interface (Unconnected) Ground terminal PCM output terminal from Sub DSP PCM output terminal from Sub DSP PCM output terminal from Sub DSP PCM output terminal from Sub DSP +3.3V power terminal (for terminal section) SDOB3 Rch zero flag output terminal SDOB3 Lch zero flag output terminal SDOB2 Rch zero flag output terminal SDOB2 Lch zero flag output terminal General purpose output terminal General purpose output terminal General purpose output terminal General purpose output terminal General purpose output terminal General purpose output terminal General purpose output terminal General purpose output terminal Ground terminal +2.5V power terminal (for internal circuit) Sub DSP: External memory data terminal 0 Sub DSP: External memory data terminal 1 Sub DSP: External memory data terminal 2 Sub DSP: External memory data terminal 3 SDOB1 Rch zero flag output terminal SDOB1 Lch zero flag output terminal SDOB0 Rch zero flag output terminal SDOB0 Lch zero flag output terminal Sub DSP: External memory data terminal 4 Sub DSP: External memory data terminal 5 Sub DSP: External memory data terminal 6 Sub DSP: External memory data terminal 7 Ground terminal +3.3V power terminal (for terminal section) Sub DSP: External memory data terminal 8 Sub DSP: External memory data terminal 9 Sub DSP: External memory data terminal 10 Sub DSP: External memory data terminal 11 Sub DSP: External memory data terminal 12 Sub DSP: External memory data terminal 13 Sub DSP: External memory data terminal 14 Sub DSP: External memory data terminal 15 Sub DSP: Column address strobe output terminal for external DRAM Sub DSP: Write enable terminal for external memory Sub DSP: Output enable terminal for external memory Sub DSP: Low address strobe output terminal for external DRAM Ground terminal +3.3V power terminal (for terminal section) Sub DSP: External memory address terminal 8 Sub DSP: External memory address terminal 7 Sub DSP: External memory address terminal 0 Sub DSP: External memory address terminal 6 Sub DSP: External memory address terminal 1


(ZF3R) (ZF3L) (ZF2R) (ZF2L) (/RINH1) (/RINH2) (/ICCDC) (DFS) (ZSEL0) (ZSEL1) (/ICCS)

(ZF1R) (ZF1L) (ZF0R) (ZF0L)

O O O O O

41


No. 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160

Name RAMA5 RAMA2 SELI13 SELI12 SELI11 SELI10 SELI9 RAMA4 RAMA3 RAMA9 RAMA10 RAMA11 VSS VDD2 SELI8 SELI7 SELI6 SELI5 RAMA12 RAMA13 RAMA14 RAMA15 RAMA16 RAMA17 OVFB/END ZEROFLG VSS NONPCM DTSDATA AC3DATA MUTE KARAOKE VDD1 SURENC CRC /LOCK DIRINT /CS SO SI SCK /IC IPINT SELI4 VSS SELI3 SELI2 TESTXI TESTXO VDD2

I/O O O I+ I+ I+ I+ I+ O O O O O

I+ I+ I+ I+ O O O O O O O O O O O O O +3.3V O O O O Is Ot Is Is Is O+ I+ I+ I+ I O +2.5V

Function Sub DSP: External memory address terminal 5 Sub DSP: External memory address terminal 2 Built-in selector input 13 (Unconnected) Built-in selector input 12 Built-in selector input 11 (Unconnected) Built-in selector input 10 (Unconnected) Built-in selector input 9 Sub DSP: External memory address terminal 4 Sub DSP: External memory address terminal 3 Sub DSP: External memory address terminal 9 (Unconnected) Sub DSP: External memory address terminal 10 (Unconnected) Sub DSP: External memory address terminal 11 (Unconnected) Ground terminal +2.5V power terminal (for internal circuit) Built-in selector input 8 (CXA) Built-in selector input 7 (GND) Built-in selector input 6 (OPTF) Built-in selector input 5 (Unconnected) Sub DSP: External memory address terminal 12 (Unconnected) Sub DSP: External memory address terminal 13 (Unconnected) Sub DSP: External memory address terminal 14 (Unconnected) Sub DSP: External memory address terminal 15 (Unconnected) Sub DSP: External memory address terminal 16 (Unconnected) Sub DSP: External memory address terminal 17 (Unconnected) Sub DSP: Overflow/program end detect terminal (Unconnected) Main DSP: Zero flag output terminal (Unconnected) Ground terminal Main DSP: Non-PCM data detect terminal Main DSP: DTS data detect terminal (Unconnected) Main DSP: AC3 data detect terminal (Unconnected) Main DSP: Auto mute detect terminal Main DSP: AC3 KARAOKE data detect terminal (Unconnected) power terminal (for terminal section) Main DSP: AC-3 2/0 mode Dolby surround encode input detect terminal (Unconnected) Main DSP: AC3 CRC error detect terminal (Unconnected) DIR: PLL lock detect terminal (Unconnected) DIR: Interrupt output terminal Microprocessor interface chip select input terminal (CSY) Microprocessor interface data output terminal Microprocessor interface data input terminal Microprocessor interface clock input terminal Initial clear input terminal Interrupt output terminal by IPORT 8-14 Built-in selector input 4 Ground terminal Built-in selector input 3 Built-in selector input 2 Test terminal (should be always connected to VSS) Test terminal (Unconnected) power terminal (for internal circuit) (SDM) (SCKY) (/ICD) (OPTD) (OPTC) (OPTB)


Is: Schmidt trigger input terminal I+: Input terminal with pull-up resistor O: Digital output terminal Ot: 3-state digital output terminal A: Analog terminal

42


P32/A10(MA2)(/D10)

P34/A12(MA4)(/D12)

P35/A13(MA5)(/D13)

P36/A14(MA6)(/D14)

P37/A15(MA7)(/D15)

P33/A11(MA3)(/D11)

IC520 : M30802SGP 16bit -COM (Main CPU)P30/A8(MA0)(/D8) P31/A9(MA1)(/D9) P15/D13/INT3 P16/D14/INT4

P42/A18(MA10) 75


VCC

P41/A17(MA9)

99

98

97

96

95

94

93

92

90

89

88

87

86

85

83

82

81

80

79

78

VCC 74

VSS

77

91

84

76

73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37

108

107

106

105

104

103

102

101

100

P43/A19(MA11)

P40/A16(MA8)

P17/D15/INT5

P20/A0(/D0)

P21/A1(/D1)

P22/A2(/D2)

P23/A3(/D3)

P24/A4(/D4)

P25/A5(/D5)

P26/A6(/D6)

P12/D10

P14/D12

P13/D11

P11/D9

P27/A7(/D7)

P120

P121

P122

P123

P124

VSS

P10/D8 P07/D7 P06/D6 P05/D5 P04/D4 P114 P113 P112 P111 P110 P03/D3 P02/D2 P01/D1 P00/D0 P157 P156 P155 P154 P153 P152 P151 VSS P150 VCC P107/AN7/K13 P106/AN6/K12 P105/AN5/K11 P104/AN4/K10 P103/AN3 P102/AN2 P101/AN1 AVSS P100/AN0 VREF AVCC R91/AD1RG/RXD4 /SCL4/STXD4

109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 10 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 11 1 2 3 4 5 6 7 8 9

P44/CS3/A20(MA12) P45/CS2/A21 P46/CS1/A21 P47/CS0/A23 P125 P126 P127 P50/WRL/WR/CASL P51/WRH/BHE/CASH P52/RD/DW P53/BCLK/ALE/CLKOUT P130 P131 VCC P132 VSS P133 P54/HLDA/ALE P55/HOLD P56/ALE/RAS P57/RDY P134 P135 P136 P137 P60/CYS0/RTS0 P61/CLK0 P62/RXD0 P63/TXD0 P64/CTS1/RTS1/CTS0/CLKS1 P65/CLK1 VSS P66/RXD1 VCC P57/TXD1 P70/TXD2/SDA2/TA0OUT (*1)

M30802SGP

(*1) N channnel Open Drain Output P94/DA1/TB4IN/CTS4/RTS2/SS4 P93/DA0/TB3IN/CTS3/RTS3/SS3 P96/ANEX1/TXD4/SDA4/SRXD4 P92/TB2IN/TXD3/SDA3/SRXD3 P91/TB1IN/RXD3/SCL2/STXD3 P71/RXD2/SCL2/TA0IN/TB0IN (*1) P73/CTS2/RTS2/TA1IN/V 8 7 8 8 P72/CLK2/TA1OUT/V BYTE P90/TB0IN/CLK3 P95/ANEX0/CLK4 P74/TA2OUT/W P84/INT2 P83/INT1 P82/INT0 RESET P85/NMI P80/TA4OUT/U P75/TA2IN/W 8 Port P7 Port P8 Port P85 Port P9 Port P10 5 P86/XCOUT XOUT P81/TA4IN/U P76/TA3OUT VSS P87/XCIN XIN P77/TA3IN CNVSS P146 P145 P144 P143 P142 P141 P140 VCC

8

8

8

8

8

8

I/O PortInside FunctionTimer

Port P0

Port P1

Port P2

Port P3

Port P4

Port P5

Port P6

Timer TA0 (16 bit) Timer TA1 (16 bit) Timer TA2 (16 bit) Timer TA3 (16 bit) Timer TA4 (16 bit) Timer TB0 (16 bit) Timer TB1 (16 bit) Timer TB2 (16 bit) Timer TB3 (16 bit) Timer TB4 (16 bit) Timer TB5 (16 bit) Watching Timer (15 bit) D-A Converter (8 bit x 2 ch)

A-D Converter (10 bit x 8 ch, Possible to 10 ch) UART/Clock Synchronized SI/O (8 bit x 5 ch) X-Y Converter (16 bit x 16 bit) CRC arithmetic Circuit (CCITT) (X16+X12+X5+1) M16C/80 Series 16 bit CPU Register R0H R0H R0L R0L R1H R1H R1L R1L R2 R2 R3 R3 SVP SVP VCT VCT SVP SVP VCT VCT FLG INTB ISP USP PC SVF SVP VCT

System clock XIN - XOUT XCIN - XCOUT

MemoryRAM 10K

DRAM Controller DMA Controller Multiplication Controller

Port P15 8

Port P14 7

Port P13 8

Port P12 8

Port P11

43


IC520 : M30802SGP Pin DescriptionNo. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 Port No. P96 P95 P94 P93 P92 P91 P90 P146 P145 P144 P143 P142 P141 P140 BYTE CNVss P87 P86 RESET XOUT VSS XIN VCC P85 P84 P83 P82 P81 P80 P77 P76 P75 P74 P73 P72 P71 P70 P67 VCC P66 VSS P65 P64 P63 P62 P61 P60 P137 P136 P135 P134 P57 P56 P55 P54 P133 VSS P132 VCC P131 P130 P53 P52 P51 P50 P127 P126 P125 P47 P46 P45 P44 P43 VCC P42 Function name TXDR RTS CTS FAN SDTN RXRDS SCKN CEBU /FLR CEM0 CEM1 RDSE CES BYTE CNVss BT232C BTYDC RESET XOUT VSS XIN VCC NMI REM1 PSW PDET VSY /ICD RXDR DMT INT938 DMTR CEP SCKP RDTP SDTP SDM VCC SDD VSS SCK /CSY CTEV CEEV CKEV /CSCS /CSPLD VRB VRA PRI I/O SO SCK I DA/O SO SI SCK O O/I (PU) O I/O I O/I (PU) O/I (PU) VSS VCC I (PU) I I OPEN VSS 12MHz VCC INT (LoEdge) INT (LoEdge) INT (LoEdge) Lo Edge O Double Edge O Lo Edge O I/O I/O ASI I/ASO SO VCC SI VSS SCK I/O O O SCK I/O O I I I OPEN Vcc /BEC VSS /Z2MT VCC /HPMT /MATT O VSS O VCC O O OPEN OPEN BASS EXTENTION CONTROL GND ZONE 2 MUTE +5V HEADPHONE MUTE MAIN -3dB OE WE FULL MUTE SWL / SWR / SW MONO FULL MUTE CENTER FULL MUTE MAIN L / R, RL / RC / RR EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS +5V EXT. ROM ADDRESS BUS O O O O OL OL OL OL Detail of function 232C TX DATA / YDC TX DATA 232C RTS / YDC CLOCK 232C CTS FAN CONTROL NON AUDIO TX DATA RDS RX DATA / FREQ SW (R VER) NON AUDIO SERIAL CLOCK BU2092 CE / ZONE2 FUNCTION FL IC RESET FL1 CE / MODEL DETECT 0 MODEL DETECT 1 RDS CE / RDS FUNCTION OSD CE / NTSC / PAL FORMAT 16 BIT DATA BUS: Vss 232C BOOT SIG. / 6CH INPUT KEY YDC BOOT SIGNAL RESET CLOCK OUT GROUND CLOCK IN +5V Un-use REMOTE CONTROL PULSE POWER SW POWER DETECT VERTICAL SYNC PULSE IC DSP IC 232C RX DATA DIGITAL FULL MUTE YSS938 IPINT DIGITAL FULL MUTE REAR L/R PLL IC CE / TUNER STEP 1 PLL IC CLOCK / TUNER STEP 0 PLL IC RX DATA PLL IC TX DATA (PU) / TUNER DSP IC TX DATA +5V DSP IC RX DATA GND DSP IC CLOCK YSS938 CE EVOL TX DATA EVOL CE EVOL CLOCK CS493X CS DIGITAL EXT. CONTROL IC CE VOLUME ROTARY B VOLUME ROTARY A I PROTECTION Power ON O I/O I I SO SI SCK O I/O O I/O I I/O I/O Vss Vcc I I I I I I O I O I O I/O I/O I I/O SO SI SCK I/O SO O SCK I/O O I I I Power OFF OL OL I I OL I OL OL I/OL OL I/OL I I/OL I/OL Vss Vcc I I I I I I OL I OL I OL I/OL I/OL I OL OL I OL OL OL OL OL OL OL I I I Backup OL OL OL OL OL OL OL OL OL OL OL OL OL OL Vss Vcc OL OL OL OL I OL OL OL OL OL OL OL OL OL OL OL OL OL OL OL OL OL OL OL OL OL I HI HI HI HI OL OL OL OL HI HI HI HI OL OL OL KEEP KEEP KEEP KEEP KEEP KEEPRX-V1200/RX-V1200RDS/ HTR-5490/RX-V2200

/FMTS /FMTC /FMTM

O O O OPEN OPEN OPEN OPEN VCC OPEN

O O O

OL OL OL

VCC

44


No. 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144

Port No. VSS P41 P40 P37 P36 P35 P34 P33 P32 P31 P124 P123 P122 P121 P120 VCC P30 VSS P27 P26 P25 P24 P23 P22 P21 P20 P17 P16 P15 P14 P13 P12 P11 P10 P07 P06 P05 P04 P114 P113 P112 P111 P110 P03 P02 P01 P00 P157 P156 P155 P154 P153 P152 P151 VSS P150 VCC P107 P106 P105 P104 P103 P102 P101 AVSS P100 VREF AVCC P97

Function name VSS A17 A16 A15 A14 A13 A12 A11 A10 A9 SCKA SDTA CEL RIMA RIMB VCC A8 VSS A7 A6 A5 A4 A3 A2 A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 /MLV PRY SPE SPB SPA D3 D2 D1 D0 DCTRG CSINT BSW PSW /HP TMT /TUNED VSS /ST VCC RMV REC PREMT ADKEY1 ADKEY0 THM PRD AVSS PRV VREF AVCC RXDR


I/O VSS

SCK SO O O O VCC VSS

O O O O O

O I(IPU)/O I(IPU) I(IPU) I(IPU) O I(IPU) VSS I(IPU) VCC AD AD AD AD AD AD AD VSS AD VCC VCC SI

Detail of function GND EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS AUDIO IC CLOCK AUDIO IC TX DATA SANYO IC CE POWER LIMITER A POWER LIMITER B +5V EXT. ROM ADDRESS BUS GND EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM ADDRESS BUS EXT. ROM DATA BUS EXT. ROM DATA BUS EXT. ROM DATA BUS EXT. ROM DATA BUS EXT. ROM DATA BUS EXT. ROM DATA BUS EXT. ROM DATA BUS EXT. ROM DATA BUS EXT. ROM DATA BUS EXT. ROM DATA BUS EXT. ROM DATA BUS EXT. ROM DATA BUS MAIN LEVEL POWER RELAY SP RELAY EFFECT SP RELAY B SP RELAY A EXT. ROM DATA BUS EXT. ROM DATA BUS EXT. ROM DATA BUS EXT. ROM DATA BUS DC TRIGGER CONTROL CS-DSP INT / ABOOT BASS EXT SW PR. DIRECT SW HEADPHONE DETECT TUNER MUTE TUNING METER GND TUNER STEREO +5V Un-use (DETECT PL TYPE) REC OUT SELECTOR POWER LIMITER DETECT KEY SW LINE 1 KEY SW LINE 0 TEMPERATURE DETECTION DC PROTECTION AD GND PS PROTECTION AD REFERENCE AD V 232C / YDC RX DATA

Power ON

Power OFF

Backup KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP OL OL OL OL OL KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP KEEP OL OL OL OL OL KEEP KEEP KEEP KEEP OL OL OL OL OL OL OL OL I I I I I I I VSS I VCC VCC OL

O O O O O

OL OL OL OL OL

O O O O O

OL OL OL OL OL

O I/O I I I O I I I I I I I I I VSS I VCC VCC I

OL OL I I I OL I I I I I I I I I VSS I VCC VCC I

45

A

B

C

D

E

F

G

H

I

J

RX-V1200/RX-V1200RDS/HTR-5490/DSP-AX1200/RX-V2200/DSP-AX2200

1

I BLOCK DIAGRAM (1/2)XL503 24.576MHz DSP IC514 YSS938 REC OUT SELECTOR DUTY CORRECTOR D/A MAIN L/R IC508 FERRITE CORE AUX INPUT SELECTOR DIR DOLBY PROLOGIC II / DOLBY DIGITAL / DTS DECORDER SOUND FIELD PROCESSING / SPEAKER CONFIGURATION / VIRTUAL PROCESSING / HEADPHONE PROCESSING D/A C IC524 D/A FL/FR D/A RC/SW D/A RL/RR IC510 2/2 AK4527B DIGITAL OUT INHIBIT 2 CD-R POWER SW SW964 VOLUME SW903 SERIAL CONTROL KEY SW941-944 RX-V1200RDS only KEY SW901-905, 945-954, 961,965 FL DISPLAY V901 FL DRIVER IC901 XL501 See page E-94/J-88 SCHEMATIC DIAGRAM Rec Out SELECTOR SW801 RX-V2200/ DSP-AX2200 only 12MHz FLASH ROM IC512 DSP TUNER SELECTOR ELECTRIC VOLUME ONSCREEN RESET DIGITAL OUT INHIBIT 1 See page E-95/J-89 SCHEMATIC DIAGRAM RX-V1200/RX-V1200RDS/HTR-5490/DSP-AX1200: See page E-92/J-86 SCHEMATIC DIAGRAM RX-V2200/DSP-AX2200: See page E-93/J-87 SCHEMATIC DIAGRAM

DSPMD/TAPE REMOTE JACK JK851, 852 IR REMOTE U901

FUNCTIONPOWER RELAY MICRO COMPUTER IC520 SPEAKER RELAY MUTE CONTROL

CD CD-R

2

DVD D-TV/LD

POWER DETECT RESET +5M

CD

LEVEL CONVERT & SIGNAL DETECT

3

CBL/SAT

DE-MODULATOR IC503 4M FLASH IC528 256K SRAM IC527

OPERATION

PLD IC526

AAC/DTS ES/NEO.6 DECODER CS493292 IC525

A/D AK4527B IC510 1/2

MAIN u-COM

4M DRAM IC502

MD/TAPE L/R

PROCESSOR DIRECT 90Hz HPF IC509 IC509

PHONES MUTE Q803, 804

IC804 3/5 1/7 PHONES

ELECTRIC IC IC516

CD-R L/R

Bass Extention IC801

3/5

1/7

Tone Control Bass/Treble VR801/802

CD L/R PHONO EQ IC501

INPUT SELECTOR IC502, 503

IC511

IC509

IC510 IC803 5/3 7/1

5/3

IC513

7/1

MAIN L/R

IC521 3/5 1/7

IC802 5/3 7/1

MAIN LEVEL 0/-10dB Q533, 534

MAIN MUTE L/R Q513, 514 Q537, 538

SPEAKER RELAY Power Amp. MAIN L/R A

4

PHONO L/R FM/AM TUNER

FL/FR REC OUT SELECTOR IC504, 505 IC508 5/3 7/1 IC509 5

IC510

MAIN L/R B IC514 7 C 6 IC525 7

7.2MHz DVD L/R

CENTER: NONE

MAIN L/R

ELECTRIC IC IC517

IC510

IC510

IC509 3

IC514 1 SW

BASS OUT: MAIN

C MUTE Q515, 539

Power Amp.

C

D-TV/LD L/R

C

CBL/SAT L/R

5VCR1 L/R

IC509 3/5

IC515 1/7 RL/RR

ELECTRIC IC IC518

RX-V2200 only

IC524 6/2 7/1

MUTE Q517, 518 RL/RR Q541, 542

Power Amp.

RL/RR RL/RR

VCR2/DVR L/R

ELECTRIC IC IC519

V-AUX L/R IC523 5 IC512 7

IC525 2 IC523 2 1 1

SW INHIBIT IC503

MUTE SW Q516, 540 MUTE RC Q519, 543 Power Amp.

SW

RC

RC

MD/TAPE L/R MUTE CONTROL RC

6

CD-R L/R 6CH INPUT VCR1 L/R MAIN L/R RX-V1200/RX-V1200RDS/HTR-5490/DSP-AX1200: See page E-92/J-86 SCHEMATIC DIAGRAM RX-V2200/DSP-AX2200: See page E-93/J-87 SCHEMATIC DIAGRAM IC507 3 IC506 3/5 1/7 1 See page E-98/J-92 SCHEMATIC DIAGRAM

VCR2/DVR L/R

CENTER SUB WOOFER

FUN

Yamaha-RXV1200_2200 rec.pdf

Documents

Transcript of Yamaha-RXV1200_2200 rec.pdf