WSAA PRODUCT APPRAISAL CERTIFICATE · Any enquiries regarding this Certificate should be directed...
Transcript of WSAA PRODUCT APPRAISAL CERTIFICATE · Any enquiries regarding this Certificate should be directed...
PA 1508 Part 1 Issue 5 Rev 0 Page 1 of 30
WSAA PRODUCT APPRAISAL CERTIFICATE
REHAU Pty Ltd – REHAU AWASHAFT DN 400 / DN 600 / DN 800 / DN 1000 Polypropylene (PP) Maintenance Shafts, Chambers and Holes
The scope of this appraisal applies to the REHAU AWASHAFT DN 400 / DN 600 / DN 800 / DN 1000 Polypropylene (PP) Maintenance Shaft, Chamber and Hole units and assemblies as listed in the attached Schedules A and B.
Product Category Polypropylene (PP) Maintenance Shafts, Chambers and Holes
PA Number: PA 1508 Par1 Issue 6 (Certificate)
Supplier REHAU Pty Ltd
Brand REHAU AWASHAFT
Standards WSA 137:2019 Issue 3 - Industry standard for Unplasticized polyvinyl chloride) (PVC-U), polypropylene (PP) and Polyethylene (PE) maintenance shafts, maintenance chambers and maintenance holes for sewerage
WSAA Product Specification
WSA PS-341 Maintenance Shafts (MS) – Polypropylene (PP) for Non-Pressure Applications – Sewerage
WSA PS-337 Maintenance Chambers (MC) – Polypropylene (PP) for Non-Pressure Applications – Sewerage
WSA PS-340 Maintenance Holes (MH) – Polypropylene (PP) for Non-Pressure Applications – Sewerage
Other Specifications
Issue date 22 October 2019
Expiry date 9 March 2023
Recommendations It is recommended that WSAA members and associates, subject to any specific requirements, accept / authorise the REHAU AWASHAFT DN 400 / DN 600 / DN 800 / DN1000 Polypropylene (PP) Maintenance Shaft, Chamber and Hole base units and assemblies as listed in Schedule B provided in pipeline design, installation, acceptance testing and commissioning in accordance with applicable WSAA Codes and the manufacturer’s requirements where specified.
Disclaimer The disclaimer on Page 2 explains a number of very important limits on your ability to rely on the information in this Product Appraisal Certificate (Certificate) and the assessment criteria used to underlay it. Please read it carefully and take it into account when considering the content in this Certificate.
PA 1508 Part 1 Issue 6 Rev 0 Page 2 of 30
1. Disclaimer
This Product Appraisal Certificate (Certificate) is issued by WSAA on the understanding that:
This Certificate applies to the product(s) as submitted in Schedule A. Any changes to the product(s) either minor or major shall void this Certificate.
To maintain the recommendations of this Certificate any such changes shall be detailed and notified to the Product Appraisal Manager for consideration and review of the Certificate including the product appraisal criteria underlying it and appropriate action. Appraisals and their recommendations will be the subject of continuous review dependent upon the satisfactory performance of products.
WSAA reserves the right to undertake random audits of product manufacture and installation. Where products fail to maintain appraised performance requirements the appraisal and its recommendations may be modified and reissued. Certificates will be reviewed and reissued at regular intervals not exceeding five (5) years.
WSAA reserves the right to withdraw this Certificate at any time in its sole and absolute discretion for any reason.
The following information explains a number of very important limits on your ability to rely on the information in this Certificate. Please read it carefully and take it into account when considering the contents of this Certificate.
Any enquiries regarding this Certificate should be directed to the Product Appraisal Manager Phone: 03 8605 7601 email [email protected].
1.1. Issue of Certificate
This Certificate has been published and/or prepared by WSAA and nominated Project Manager and peer group of technical specialists (the Publishers).
The Certificate and the underlying product appraisal criteria have been prepared for use within Australia only by technical specialists that have expertise in the function of products such as those appraised in the Certificate (the Recipients).
By accepting this Certificate, the Recipient acknowledges and represents to the Publisher(s) and each person involved in the preparation of the Certificate and product appraisal criteria underlying it that the Recipient has understood and accepted the terms of this Disclaimer.
1.2. Limits on Reliance on Information and Recommendations
1.2.1. Disclaimer of liability
Neither the Publisher(s) nor any person involved in the preparation of the Certificate and product appraisal criteria underlying it accept(s) any liability for any loss or damage suffered by any person however caused (including negligence or the omission by any person to do anything) relating in any way to the Certificate or the product appraisal criteria underlying it. This includes (without limitation) any liability for any recommendation or information in the Certificate or any errors or omissions.
1.2.2. Intellectual Property and other rights
WSAA does not undertake any assessment of whether the importation, manufacture, sale or use of the Product the subject of this Certificate infringes the intellectual property rights or proprietary rights of any person. Recipients of the Certificate should undertake their own assessment of whether (as relevant) the importation, manufacture, sale or use of the relevant Products infringe the intellectual property rights or other proprietary rights of any person. If the Product infringes intellectual property rights or other proprietary rights there is potential for the supply of the Products to be interrupted.
From time to time WSAA and the other Publishers may receive notice of allegations that the importation, manufacture, sale or use of the Product infringes intellectual property rights or other proprietary rights. WSAA's policy is to not refer to such allegations in its Certificate or take any other steps to put Recipients on notice of such allegations. If, however, WSAA becomes aware that the allegations have been admitted or proved in Court, then WSAA may, at its discretion, take such steps as it considers appropriate. As such, Recipients acknowledge, agree and accept that WSAA may have information in its possession about intellectual property rights infringement allegations or other infringement allegations in relation to the Product which are not referred to or disclosed in this Certificate and which are not otherwise communicated to Recipients.
1.2.3. Need for independent assessment
The information and any recommendation contained (expressly or by implication) in this Certificate are provided in good faith (and subject to the limitations noted in this Certificate). However, you should treat the information as indicative only. You should not rely on that information or any such recommendation except to the extent that you reach an agreement to the contrary with the Publisher(s).
This Certificate does not contain all information that a person might require for the purposes of assessing any product discussed or appraised within it. The product appraisal criteria used in preparing this Certificate may not address all relevant aspects of the Product.
Recipients should seek independent evidence of any matter which is material to their decisions in connection with an assessment of the Product and consult their own advisers for any technical information required. Any decision to use the Product should take into account the reliability of that independent evidence obtained by the Recipient regarding the Product. Recipients should also independently verify and assess the appropriateness of any recommendation in the Certificate, especially given that any recommendation will not take into account a Recipient’s particular needs or circumstances.
WSAA has not evaluated the extent of the product liability and professional indemnify insurance that the provider of the product maintains. Recipients should ensure that they evaluate the allocation of liability for product defects and any professional advice obtained in relation to the product or its specification including the requirements for product liability and professional indemnity insurance.
1.3. No Updating
Neither the Publisher(s) nor any person involved in the preparation of this Certificate or the product appraisal criteria underlying it [has] [have] any obligation to notify you of any change in the information contained in this Certificate or of any new information concerning the Publisher(s) or the Product or any other matter.
1.4. No Warranty
The Publisher(s) do[es] not, in any way, warrant that steps have been taken to verify or audit the accuracy or completeness of the information in this Certificate, or the accuracy, completeness or reasonableness of any recommendation in this Certificate.
PA 1508 Part 1 Issue 6 Rev 0 Page 3 of 30
SCHEDULE A
APPENDIX A - PRODUCT CERTIFICATIONS
Copies of the following Quality and Product Certification Certificates are available for downloading from the WSAA ‘Members Only’ project portal website.
SCHEDULE A1 - REHAU – QUALITY MANAGEMENT SYSTEMS
Business Location: REHAU AG + Co, Rheniumhaus Otto-Hahn-Str. 2, D-95111 Rehau, GERMANY
There are 30 more locations of administration offices and plants included in this certification as detailed in the attachment.
Quality Systems Standard ISO 9001:2008
Certificate Registration no. 01 104 0101700
Certifying agency TÜV Rheinland Cert GmbH
First date of certification NA
Current date of certification 29 June 2015
Expiry date of certification 21 June 2021
SCHEDULE A2: M.O.L – QUALITY MANAGEMENT SYSTEMS
Business Location: M.O.L Gummiverarbeitung GmbH & Co. KG, GutenbergstraBe 12 – 14, 49377
Vechta, GERMANY
Quality Systems Standard ISO 9001:2015
Certificate Registration no. 496810 QM15
Certifying agency DQS UL Management Systems Solutions
First date of certification 20 March 2017
Current date of certification 20 March 2017
Expiry date of certification 30 January 2020
NOTE: DQS UL Management Systems Solutions is accredited by DAkkS Deutsche Akkreditierungsstelle
PA 1508 Part 1 Issue 6 Rev 0 Page 4 of 30
SCHEDULE A
SCHEDULE A3: M.O.L – DECLARATION OF PERFORMANCE
According to Declaration (EU) No. 305/2011
Business Location: M.O.L Gummiverarbeitung GmbH & Co. KG, GutenbergstraBe 12 – 14, 49377
Vechta, GERMANY
Product Standard/Spec. EN 681-1:2002
Certificate Registration no. BL-001-2013
Certifying agency M.O.L Gummiverarbeitung GmbH & Co. KG
First date of certification NA
Current date of certification 12 July 2013
Expiry date of certification NA
SCHEDULE A4: BOREALIS GROUP – QUALITY MANAGEMENT SYSTEMS
A total 18 sites belongs to Borealis Group in Germany, Belgium, Hungary, Italy, Romania, Serbia, Sweden, Finland, Slovakia and Austria is included in this certification.
Quality Systems Standard ISO 9001:2015
Certificate Registration no. A180432
Certifying agency International Certification Management GmbH
First date of certification NA
Current date of certification 28 May 2018
Expiry date of certification 27 May 2021
NOTE: DQS UL Management Systems Solutions is accredited by DAkkS (Deutsche Akkreditierungsstelle)
SCHEDULE A5: TOTAL PETROCHEMICAL – QUALITY MANAGEMENT SYSTEMS
A total 10 sites belongs to Total petrochemical Group in Belgium, USA, France, Spain and China. The certification of Feluy s.a in Belgium site is included in this table.
Quality Systems Standard EN ISO 9001:2015
Certificate Registration no. 92 QMS 068i
Certifying agency Vinçotte sa, Belgium
First date of certification 19 June 2006
Current date of certification 9 April 2018
Expiry date of certification 8 April 2021
PA 1508 Part 1 Issue 6 Rev 0 Page 5 of 30
SCHEDULE A
SCHEDULE A6: MFPA WEIMAR GERMANY – INSPECTION, LABORATORY AND CERTIFICATION BODIES
Testing facility: MFPA Official Testing Centre located in 99423 Weimar, Germany
Certification Standard
a) Inspection body - Type A to DIN EN ISO/IEC 17020:2012
b) Laboratory Accreditation – DIN EN ISO/IEC 17025:2005
c) Certification Body - DIN EN ISO/IEC 17065:2005
Certificate Registration no.
a) D-IS-11143-01-00
b) D-PL-11021-01-00
c) D-ZE-11143-01-00
Certifying agency DakkS (Deutsche Akkreditierungsstelle GmbH)
First date of certification
a) 8 May 2012
b) NA
c) 7 November 2014
Current date of certification
a) 19 December 2016
b) 19 December 2016
c) 7 November 2014
Expiry date of certification
a) 18 December 2021
b) 18 December 2021
c) 5 November 2019
SCHEDULE A2 - REHAU – QUALITY MANAGEMENT SYSTEMS
Business Location: REHAU Pty Ltd REHAU PTY LTD, Suite 1.02, Level 1, Quad 1, 8 Parkview Drive,
Sydney Olympic Park NSW 2127
Water Industry Standard WSA 137:2013
Certificate Registration no. AMI 74663
Certifying agency ApprovalMark
First date of certification 30/11/2017
Original Certified 30/11/2017
Expiry date of certification 30/11/2022
Current Certification 30/11/2017
PA 1508 Part 1 Issue 6 Rev 0 Page 6 of 30
SCHEDULE B
TABLE B1 AWASHAFT DN 400 PP MS PRODUCT SCHEDULE
Product Supplier Picture
AWASHAFT DN 400/315 PP
Chamber Base GD
REHAU
AWASHAFT DN 400/315 PP
Chamber Base RML
REHAU
REHAU’s AWADUCT DN 400/315
or DN 315/250 Offset Reducer
with lip sealing ring; Material
RAU-PVC 1100, Colour RAL 8023
red brown
REHAU
(optional item, not included in
this appraisal, but included in
PA 1508 Part 2)
REHAU’s AWADUCT KGB PVC-U
Bend SN8 with lip sealing rings
from 15° to 87°; Material RAU-
PVC 1100, Colour RAL 8023 red
brown (AWADUCT PVC SN8
Classic Range to EN 1401
(equivalent to AS/NZS 1260)
REHAU
(optional item, not included in this appraisal; alternative PVC-U bends locally available to AS/NZS 1260)
AWADUCT PP Ball joint –
continuously adjustable up to +/-
7.5o horizontally or vertically with
EPDM sealing rings (Safety-Lock)
REHAU
(optional item, not included in this appraisal, but included in PA 1508 Part 2)
Extension pipe or riser DN 300 or
DN 225 PVC-U DWV SN8 to
AS/NZS 1260
Installer
PA 1508 Part 1 Issue 6 Rev 0 Page 7 of 30
SCHEDULE B
Product Supplier Picture
DN 150 PVC-U push-in socket
plugs to AS/NZS 1260 for unused
branch of triple inlet RML base
unit
Installer
Injection moulded DN 300 or DN
225 PVC-U SWJ push on cap to
AS/NZS 1260
Installer
Injection moulded DN 300 or DN
225 PVC-U solvent weld on cap
with screw lid and RR seal to
AS/NZS 1260
Installer
PE Shroud Pipe (450mm dia
minimum) to AS/NZS 4130,
Concrete Surround and Surface
Fittings (DI access cover to AS
3996 Class B or D)
Installer
The DN 400 GD chamber base measures 530 mm in length and 360 mm in height (reducer not included in this
appraisal, but in PA 1508 Part 2) and the DN 400 RML measures 480 mm in length and 360 mm in height (reducer
not included in this appraisal, but in PA 1508 Part 2.).
FIGURE B1 AWASHAFT DN 400 PP MS BASE UNIT
TABLE B2 AWASHAFT DN 400 PP MS BASE
Chamber base unit DN Inlet / outlet
DN/OD M (mm) Z (mm) N (mm)
Length (mm)
Height H2 (mm)
AWASHAFT DN/OD 400 GD chamber base
(straight connecting passage)
400 160 74 383 189 530 360
AWASHAFT DN/OD 400 RML (3 inlets, 1 outlet)
400 160 74 329 189 480 360
PA 1508 Part 1 Issue 6 Rev 0 Page 8 of 30
SCHEDULE B
TABLE B3: AWASHAFT DN 600 PP MC PRODUCT SCHEDULE
Product Picture Supplier
AWASHAFT DN 600 PP
Chamber Base as per the
manufacturer schedule
(refer to following pages)
REHAU
Elastomeric seals for
components
a) DN600 lip sealing for
top of the base unit
b) DN160, 200, 250, 315
and 400 lip sealing ring
for inlet / outlet
c) DN600 lip sealing ring
for riser rings
MOL
AWASHAFT DN 600 PP
riser
REHAU
AWADUCT PP Pipes and
Fittings
REHAU
(optional item, not included in this appraisal, but in PA 1508 Part 2)
AWADOCK PP Fittings
REHAU
(optional item, not included in this appraisal, but in PA 1508 Part 2)
PA 1508 Part 1 Issue 6 Rev 0 Page 9 of 30
SCHEDULE B
Product Picture Supplier
Telescopic part
REHAU
(optional item. Allows height adjustment by 300mm, suitable for load class B application)
Concrete Load bearing ring
REHAU
DI access cover to AS 3996
Class B or D
Installer
FIGURE B2 AWASHAFT DN 600 PP MC BASE UNIT
PA 1508 Part 1 Issue 6 Rev 0 Page 10 of 30
SCHEDULE B
TABLE B4 AWASHAFT DN 600 PP MC BASE
Chamber base unit
Bend DN/OD
Inlet / outlet
mm
Effective height N
mm
Height H
mm
h¹
mm
h2
mm
AWASHAFT PP DN/OD 600 chamber bases ,
straight ( Refer to Figure B2)
straight
160 250 536 206
200 290 536 206
250 330 600 206
315 385 664 210
400 430 710 201
FIGURE B3 AWASHAFT PP DN 600 PP MC BASE - RML90º, T-PIECE 90º,AG90º
TABLE B5 AWASHAFT PP DN 600 PP MC BASE - RML90º,T-Piece 90º,AG90º
Chamber base unit
Bend DN/OD Inlet / outlet
mm
Effective height N
mm
Height H
mm
h¹
mm
h2
mm
RML90º
160 250 560 206
200 290 560 206
250 330 710 206
315 385 710 206
RM 270º
160 250 560 206
200 290 560 206
250 330 710 206
315 385 710 206
ML90º
160 250 560 206
200 290 560 206
PA 1508 Part 1 Issue 6 Rev 0 Page 11 of 30
SCHEDULE B
Chamber base unit
Bend DN/OD Inlet / outlet
mm
Effective height N
mm
Height H
mm
h¹
mm
h2
mm
250 330 710 206
315 385 710 206
RML90º/270º
160 250 560 206
200 290 560 206
250 330 710 206
315 385 710 206
AG90º
160 250 560 206
200 290 560 206
250 330 710 206
315 385 710 206
AG270º
160 250 560 206
200 290 560 206
250 330 710 206
315 385 710 206
FIGURE B4 AWASHAFT PP DN 600 PP MC BASE -30º, 45º, 60º Deflection
PA 1508 Part 1 Issue 6 Rev 0 Page 12 of 30
SCHEDULE B
TABLE B6 AWASHAFT PP DN 600 PP MC BASE –30º,60º 90º deflection
Chamber base unit
Angle deflection
DN/OD Inlet / outlet
mm
Effective height N
mm
Height H
mm
h¹
mm
h2
mm
Standard
30º 160 260 556 210 8
200 278 556 210 8
45º 160 260 556 210 8
200 278 556 210 8
60º 160 260 556 210 8
200 278 556 210 8
FIGURE B5 AWASHAFT PP DN 600 PP RISER PIPE
TABLE B7 AWASHAFT PP DN 600 PP RISER PIPE
Riser Pipe Installation Da
mm
Di
mm
With/ with out Inliner
700 680 600
1000 680 600
1200 680 600
1500 680 600
2000 680 600
3000 680 600
6000 680 600
PA 1508 Part 1 Issue 6 Rev 0 Page 13 of 30
SCHEDULE B
FIGURE B6 AWASHAFT PP DN 600 PP Telescopic part
TABLE B8 AWASHAFT PP DN 600 PP Telescopic part
Telescopic part Pipe
N1
mm
N2
mm
H
mm
Di
mm
D2
mm
300 140 490 590 770
300 140 490 590 850
FIGURE B7 AWASHAFT PP DN 600 Concrete Load Bearing Ring
TABLE B9 AWASHAFT PP DN 600 Concrete Load Bearing Ring
DN
mm
Weight
kg
625 155
PA 1508 Part 1 Issue 6 Rev 0 Page 14 of 30
SCHEDULE B
TABLE B10: AWASHAFT DN 800 PP MC PRODUCT SCHEDULE
Product Picture Supplier
AWASHAFT DN 800 PP
Chamber Base as per the
manufacturer schedule (refer
to following pages)
REHAU
AWASHAFT DN 800 PP
riser (with and without
ladder)
REHAU
DN 800/625 PP cone
REHAU
Elastomeric seals for
components
a) DN800 lip sealing for
top of the base unit
b) DN160, 200, 250, 315
and 400 lip sealing ring
for inlet/outlet
c) DN800 lip sealing ring
for riser rings
d) DN625 lip sealing ring
for top of the cone
MOL
AWADUCT PP Fittings
REHAU
(optional item, not included in this appraisal, but in PA 1508 Part 2)
PA 1508 Part 1 Issue 6 Rev 0 Page 15 of 30
SCHEDULE B
Product Picture Supplier
AWADUCT PP Fittings
REHAU
(optional item, not included in this appraisal, but in PA 1508 Part 2)
AWADOCK PP Fittings
REHAU
(optional item, not included in this appraisal, but in PA 1508 Part 2)
Push on caps according to
water agency requirements
Installer
(not included in this appraisal)
Ladder
This item is not included in the appraisal as DN800 is being assessed as MC and there is no man entry.
Rehau supplies the ladders.
The supports of Ladders are
injection moulded into the
risers. The steps are
assembled
REHAU
(not included in this appraisal)
1000/800 polymer bearing
ring DN625 to EN 13598-2
Material – Polymer, Grey
colour
REHAU
PA 1508 Part 1 Issue 6 Rev 0 Page 16 of 30
SCHEDULE B
Product Picture Supplier
FIGURE B8 AWASHAFT PP DN 800 MC STANDARD BASES
TABLE B11 AWASHAFT PP DN 800 MC STANDARD BASES
Chamber base unit
Bend DN/OD Inlet / outlet
mm
Effective height N
mm
Height H
mm
Weight
kg
180ºGD
160 455 535 23
200 495 535 24
250 535 665 27
315 590 600 32
RML90º
125 425 535 22
160 455 535 23
200 495 535 24
250 535 600 27
315 590 665 32
RM 270º 160 455 535 23
PA 1508 Part 1 Issue 6 Rev 0 Page 17 of 30
SCHEDULE B
Chamber base unit
Bend DN/OD Inlet / outlet
mm
Effective height N
mm
Height H
mm
Weight
kg
200 495 535 24
250 535 600 27
315 590 665 32
ML90º
160 455 535 23
200 495 535 24
250 535 600 27
315 590 665 32
RML90º/270º
160 455 535 23
200 495 535 24
250 535 600 27
315 590 665 32
AG90º
160 455 535 23
200 495 535 24
250 535 600 27
315 590 665 32
AG270º
160 455 535 23
200 495 535 24
250 535 600 27
315 590 665 32
FIGURE B9 AWASHAFT PP DN 800 PROJECT SPECIFIC BASES – STRAIGHT
PA 1508 Part 1 Issue 6 Rev 0 Page 18 of 30
SCHEDULE B
TABLE B12 AWASHAFT PP DN 800 PROJECT SPECIFIC BASES - STRAIGHT
Chamber base unit DN/OD Inlet / outlet
mm
Effective height N
mm
Height H
mm weight
STRAIGHT
110 310 470 30
125 310 470 32
160 310 470 33
200 310 470 34
250 435 595 40
315 435 595 42
400 435 595 46
FIGURE B10 AWASHAFT PP DN 800 PROJECT SPECIFIC BASES - ANGLED
TABLE B13 AWASHAFT PP DN 800 PROJECT SPECIFIC BASES - ANGLED
Chamber base unit
DN/OD Inlet / outlet
mm
Effective height N
mm
Height H
mm weight
ANGLED
110 310 470 30
125 310 470 32
160 310 470 33
200 310 470 34
250 435 595 40
315 (Max 45º) 435 595 42
400 (Max 30º) 435 595 46
PA 1508 Part 1 Issue 6 Rev 0 Page 19 of 30
SCHEDULE B
FIGURE B11 AWASHAFT PP DN 800 CONE
TABLE B14 AWASHAFT PP DN 800 CONE
CONE Version N max
mm
H Min
mm
Height H weight
DN800 With/with out ladder 615 365 710 29
FIGURE B12 AWASHAFT PP DN 800 RINGS
TABLE B15 AWASHAFT PP DN 800 RINGS
RINGS Version Effective Length N
mm
Height H
mm weight
DN800
Inc Vertical latter/ Ex.Ladder 125 220 7
Inc Vertical latter/ Ex.Ladder 250 345 11
Inc Vertical latter/ Ex.Ladder 375 470 16
Inc Vertical latter/ Ex.Ladder 500 595 20
Inc Vertical latter/Ex.Ladder 625 720 24
Inc Vertical latter/Ex.Ladder 750 845 29
Inc Vertical latter/ Ex.Ladder 875 970 33
PA 1508 Part 1 Issue 6 Rev 0 Page 20 of 30
SCHEDULE B
TABLE B16: AWASHAFT DN 1000 PP MH PRODUCT
Product Picture Supplier
AWASHAFT DN 1000 PP Chamber
Base as per the manufacturer
schedule (refer to following pages)
REHAU
Elastomeric seals for components
a) DN1000 lip sealing for top of the
base unit
b) DN160, 200, 250, 315 and 400 lip
sealing ring for inlet/outlet
c) DN1000 lip sealing ring for riser
rings
d) DN625 lip sealing ring for top of
the cone
MOL
DN 1000/625 PP cone
REHAU
DN 1000/800 PP cone/adaptor
REHAU
PA 1508 Part 1 Issue 6 Rev 0 Page 21 of 30
SCHEDULE B
Product Picture Supplier
AWASHAFT DN 1000 PP riser (with
ladder)
REHAU
AWADUCT PP Fittings
REHAU
(optional items, not included in this appraisal, but in PA 1508 Part 2)
AWADOCK PP Fittings
REHAU
(optional items, not included in this appraisal, but in PA 1508 Part 2)
Ladder
This item is included in the appraisal as DN1000 MH is being assessed as man entry.
REHAU
(Rehau supplies the ladders. The supports of Ladders are injection moulded into the risers. The steps are assembled)
PA 1508 Part 1 Issue 6 Rev 0 Page 22 of 30
SCHEDULE B
Product Picture Supplier
Polymer load bearing ring DN 625
REHAU
Concrete Load bearing ring DN 800
REHAU
Concrete load bearing ring DN 625
REHAU
The DN 1000 MH base measures 1316mm in length and 604mm in height
FIGURE B13 AWASHAFT PP DN 1000 STANDARD CHAMBER BASE
PA 1508 Part 1 Issue 6 Rev 0 Page 23 of 30
SCHEDULE B
TABLE B17 AWASHAFT PP DN 1000 MH STANDARD BASES
Chamber base unit
Bend OD inlet/outlet
mm
Effective height N
mm
Height H
mm
Weight
kg
180ºGD
160 435 605 62
200 435 605 72
250 435 605 74
315 435 605 72
400 480 605 83
15° ( 165° or 195°)
200 435 605 70
315 435 605 75
30° (150° or 195°)
200 435 605 69
315 435 605 75
45°(135° or 225°)
200 435 605 70
60°(120° or 240°)
200 435 605 70
90° or 270°
200 435 605 80
250 435 605 80
315 435 605 80
RML90º
200 435 605 79
250 435 605 80
315 435 605 81
RM 270º 200 435 605 89
250 435 605 89
PA 1508 Part 1 Issue 6 Rev 0 Page 24 of 30
SCHEDULE B
Chamber base unit
Bend OD inlet/outlet
mm
Effective height N
mm
Height H
mm
Weight
kg
315
435 605
89
ML90º
200 435 605 88
250 435 605 89
315 435 605 90
200 495 535 24
250 535 600 27
315 590 665 32
RML45º
200 435 605 82
RM 225º
200 435 605 85
ML135º
200 435 605 85
RL135º/225º
200 435 605 85
FIGURE B14 AWASHAFT PP DN 1000 PROJECT SPECIFIC BASES STRAIGHT
PA 1508 Part 1 Issue 6 Rev 0 Page 25 of 30
SCHEDULE B
TABLE B18 AWASHAFT PP DN 1000 PROJECT SPECIFIC BASES – STRAIGHT
(Usable height 435 mm for chamber height ≤ 1496mm)
Chamber base unit OD Inlet / outlet
mm
Usable height H
mm
Height H
mm Weight kg
STRAIGHT
160 435 605 64
200 435 605 66
250 435 605 71
315 435 605 79
TABLE B19 AWASHAFT PP DN 1000 PROJECT SPECIFIC BASES – STRAIGHT
(Usable height 935 mm for chamber height ≥ 1496mm)
Chamber base unit OD Inlet / outlet
mm
Usable height H
mm
Height H
mm Weight kg
STRAIGHT
160 935 1105 64
200 935 1105 66
250 935 1105 71
315 935 1105 79
400 935 1105 124
500 935 1105 145
630 935 1105 179
FIGURE B15 AWASHAFT PP DN 1000 PROJECT SPECIFIC BASES - ANGLED
PA 1508 Part 1 Issue 6 Rev 0 Page 26 of 30
SCHEDULE B
TABLE B20 AWASHAFT PP DN 1000 PROJECT SPECIFIC BASES – ANGLED
(Usable height 435 mm for chamber height ≤ 1496mm)
Chamber base unit
DN Inlet / outlet
mm
Usable height H
mm
Height H
mm Weight kg
ANGLED
160 435 605 64
200 435 605 66
250 435 605 70
315 435 605 78
TABLE B21 AWASHAFT PP DN 1000 PROJECT SPECIFIC BASES - ANGLED
(Usable height 935 mm for chamber height ≥ 1496mm)
Chamber base unit
DN Inlet / outlet
mm
Usable height H
mm
Height H
mm Weight kg
ANGLED
160 435 605 64
200 435 605 66
250 435 605 70
315 435 605 78
FIGURE B14 AWASHAFT PP DN 1000 EMPTY BASE
TABLE B22 AWASHAFT PP DN 1000 EMPTY BASE
Chamber base unit
Usable height H
mm
Height H
mm Weight kg
EMPTY BASE
475 605 59
975 1105 89
PA 1508 Part 1 Issue 6 Rev 0 Page 27 of 30
SCHEDULE B
FIGURE B15 AWASHAFT PP DN 1000 RISER RINGS
TABLE B23AWASHAFT PP DN 1000 RINGS
RINGS Version Useable Length N
mm
Height H
mm weight
DN 1000
Inc Vertical latter 125 220 20
Inc Vertical latter 250 345 22
Inc Vertical latter 500 595 36
Inc Vertical latter 750 845 48
Inc Vertical latter 1000 1095 65
Excl ladder 125 220 12
Excl ladder 250 345 22
Excl ladder 500 595 32
Excl ladder 750 845 46
Excl ladder 1000 1095 59
PA 1508 Part 1 Issue 6 Rev 0 Page 28 of 30
SCHEDULE B
FIGURE B16 AWASHAFT PP DN 1000/625 CONE
TABLE B24 AWASHAFT PP DN 1000/625 CONE
CONE Description N max
mm
N Min
mm
Height H Weight
kg
DN1000/625 With vertical ladders 820 570 915 45
DN1000/625 Without vertical ladders 820 570 915 43
FIGURE B17 AWASHAFT PP DN 1000/800 CONE
TABLE B25 AWASHAFT PP DN 1000/800 CONE
CONE Useable length
mm
Height H Weight
kg
DN1000/625 500 595 28
PA 1508 Part 1 Issue 6 Rev 0 Page 29 of 30
SCHEDULE B
FIGURE B18 AWASHAFT DN 1000/800 POLYMER BEARING RING DN 625
TABLE B26 AWASHAFT DN 1000/800 POLYMER BEARING RING DN 625
RINGS Description DN
mm
Weight
kg
DN 1000/800
Polymer bearing ring 625 45
Seal cone bearing ring (rubber). sand-tight
635 .5
Polymer mortar for polymer bearing ring ( for 2 bearing rings)
25
FIGURE B19 AWASHAFT DN 1000/800– CONCRETE BEARING RING
TABLE B27 AWASHAFT DN 1000/800– CONCRETE BEARING RING
DN
mm
Weight
kg
625 155
FIGURE B20 AWASHAFT DN 1000/800 – CONCRETE SUPPORT RING DN 800
TABLE B28 AWASHAFT DN 1000/800 – CONCRETE SUPPORT RING DN 800
PA 1508 Part 1 Issue 6 Rev 0 Page 30 of 30
SCHEDULE B
DN
mm
Weight
(Kg)
800 300
FIGURE B21 AWASHAFT DN 1000/800/600 – CONCRETE BEARING RING VIATOP
TABLE B29 AWASHAFT DN 1000/800/600 – CONCRETE BEARING RING VIATOP
DN
mm
Weight
kg
625 -
FIGURE B24 AWADOCK CONNECTION - CONNECTION OF SEWER PIPES MADE OF PVC AND PP
TABLE B30 AWADOCK CONNECTION - CONNECTION OF SEWER PIPES MADE OF PVC AND PP
Length of spigot end
(mm)
DN/ID
mm
DN/OD
mm
Bore diameter
mm
60 150 160 200
50 175 200 250