Wood Double Hung Window - Custom Windows & Doors · : United Window and Door Systems test facility...
Transcript of Wood Double Hung Window - Custom Windows & Doors · : United Window and Door Systems test facility...
WWW.MOLIMO.NET
TEST REPORT AAMA/WDMA/CSA 101/I.S.2/A440-17 REPORT NO.: 1686.05-106-12 RENDERED TO: REVIVAL SASH Springfield, New Jersey PRODUCT TYPE: Wood Double Hung Window SERIES / MODEL: 5200
Test Summary of Results Primary Product Designator Class CW – PG75 1668 x 2515 (66 x 99)-H
Design Pressure ±3600 Pa (±75.19 psf)
Air Infiltration 1.3 L/s/m2 (0.26 cfm/ft2)
Water Penetration Resistance Test Pressure 540 Pa (11.28 psf) Test Completion Date: 10/12/2018 Reference must be made to Report No. 1686.05-106-12, dated 4/18/2019 for complete test specimen description and detailed test results.
Report No.: 1686.05-106-12 Report Date: 4/18/2019
Page 2 of 8
WWW.MOLIMO.NET
CLIENT INFORMATION: REVIVAL SASH 135 East 57th Street Springfield, New Jersey 10022 TEST LABORATORY: Molimo, LLC 1410 Eden Road York, Pennsylvania 17402 717-900-6034 PROJECT SUMMARY:
PRODUCT TYPE: Wood Double Hung Window
SERIES/MODEL: 5200
PROJECT SUMMARY: Molimo, LLC was contracted to perform testing on the above referenced product. The results are tested values and were secured by using the designated test methods. A summary of the ratings achieved for the specimen tested are shown in the table below.
SPECIMEN SPECIFICATION PRODUCT RATING
1 101/I.S.2/A440-17 Class CW – PG75 1668 x 2515 (66 x 99)-H
PROJECT DETAILS: Test Dates: 10/3/2018 – 10/12/2018
Test Record Retention End Date: 10/12/2022
Test Location: United Window and Door Systems test facility in Springfield, New Jersey. In accordance with AAMA 205.01, calibration of manufacturers' test equipment is documented under Report No. 1686.01-106-12.
Test Specimen Source: The test specimen was provided by the client. Representative samples of the test specimen will be retained by Molimo for a minimum of four years from the test completion date.
Drawing Reference: The test specimen drawings were supplied by the client. The test specimen construction was verified by Molimo and was found to be representative of the product tested. Test specimen drawings are located in Appendix D of this report.
Report No.: 1686.05-106-12 Report Date: 4/18/2019
Page 3 of 8
WWW.MOLIMO.NET
WITNESSES: The following representatives witnessed all or part of the testing.
Name Company Kevin Vazquez Revival Sash Rafal Kiwowicz Revival Sash
Michael D. Stremmel, P.E. Molimo, LLC TEST METHODS:
AAMA/WDMA/CSA 101/I.S.2/A440-17, NAFS 2017 - North American Fenestration Standard/Specification for Windows, Doors, and Skylights
AAMA 910-10, Voluntary "Life Cycle" Specifications and Test Methods for AW Class Architectural Windows and Doors
TEST SPECIMEN DESCRIPTION:
PRODUCT SIZES: Overall Size: 1668 mm x 2515 mm (65-11/16" x 99") Overall Area: 4.20 m2 (45.16 ft2) Exterior Sash: 1461 mm x 1222 mm (57-1/2" x 48-1/8") Interior Sash: 1461 mm x 1254 mm (57-1/2" x 49-3/8")
FRAME CONSTRUCTION: Material: Milled mahogany wood Corner Details: Coped and butted, sealed with sealant, and secured with #8 x 3" wood
screws, three per corner. Other Details:
The head frame was constructed from four pieces; the main frame, an exterior blind stop, an interior sash stop, and a parting strip between the sash tracks. The blind stop was secured with #8 wood screws spaced 12"on center. The sash stop and parting strip were secured with brad nails spaced 12" on center. The sill frame was constructed from two piece; the main frame and the interior sash stop. The sash stop was secured with brad nails spaced 12"on center.
Report No.: 1686.05-106-12 Report Date: 4/18/2019
Page 4 of 8
WWW.MOLIMO.NET
TEST SPECIMEN DESCRIPTION: (Continued)
FRAME CONSTRUCTION: Other Details: (Continued)
The jamb frames were constructed from six pieces; the main frame, an interior sash stop, a parting strip between the sash tracks, interior and exterior weight box pieces and a plywood weight box cover. The sash stops, and parting strips were secured to the main frame with brad nails spaced 6" on center. The interior and exterior weight box covers were secured with #8 wood screws spaced 12" on center. The plywood weight box cover was secured to the interior and exterior weight box covers with #8 wood screws spaced 12" on center.
SASH CONSTRUCTION: Material: Milled mahogany wood Corner Details: Coped and butted, sealed with sealant and secured with #8 x 3" wood
screws. The interior sash bottom rail and exterior sash top rail utilized two screws per corner and the interior and exterior sash meeting rails utilized one screw per corner.
Other Details: The interior and exterior meeting rails utilized and applied check rail, secured with brad nails spaced 12" on center.
REINFORCEMENT: No reinforcement was utilized.
GLAZING DETAILS: No conclusions of any kind regarding the adequacy or inadequacy of the glass in any glazed test specimen can be made.
Description Detail Glass Type 7/8" IG
Glazing Construction (exterior to interior)
3/16" thick heat strengthened glass 1/2" plastic and metal reinforced spacer system 3/16 thick heat strengthened glass
Glazing Method Set from the interior against a bead of silicone and secured with wood glazing beads secured with brad nails spaced 12" on center.
Glazing Bite 1/2" Daylight Opening Interior Sash: Exterior Sash:
1324 mm x 1105 mm (52-1/8" x 43-1/2") 1324 mm x 1105 mm (52-1/8" x 43-1/2")
Report No.: 1686.05-106-12 Report Date: 4/18/2019
Page 5 of 8
WWW.MOLIMO.NET
TEST SPECIMEN DESCRIPTION: (Continued)
WEATHERSTRIPPING:
Description Quantity Location Kerf-mounted foam-filled vinyl
bulb seal 2 Rows Center sash parting strip, exterior sash top rail, and all sash stiles
Kerf-mounted foam-filled vinyl bulb seal 1 Row Interior and exterior sash stops
Kerf-mounted 0.150" high polypile with center fin 1 Row Interior and exterior meeting rails
Custom shaped, kerf-mounted EPDM gasket 1 Row Exterior meeting rail
0.350" diameter hollow vinyl bulb 2 Rows Interior sash bottom rail
DRAINAGE: A sloped sill was utilized.
HARDWARE:
Description Quantity Location Weight and chain balance system
2 per sash One in each jamb
Brass sweep locks 2 Interior meeting rail, 13" from each end
INSTALLATION: The specimen was installed into a Spruce-Pine-Fir wood buck. The rough opening allowed for a 3/8" shim space. The exterior perimeter of the specimen was sealed with sealant.
Location Anchor Description Anchor Spacing
Head, sill, and jambs
1" wide x 6" long, 14 ga (0.078") steel straps secured to the window with two #8 x 1-1/4" wood screws
and secured to the wood buck with two 1/4" x 1-1/2" screws
6" from each corner and spaced 12" on center
Report No.: 1686.05-106-12 Report Date: 4/18/2019
Page 6 of 8
WWW.MOLIMO.NET
TEST RESULTS: The temperature during testing was 22.8 oC (73 oF).
OPERATING FORCE: First Half (per ASTM E 2068)
Test Results Allowable Exterior Sash
Initiate Motion 182 N (40.9 lbf) 280 N (63 lbf) Maintain Motion (Opening) 58 N (13 lbf) 200 N (45 lbf) Maintain Motion (Closing) 31 N (7 lbf) 200 N (45 lbf)
Interior Sash Initiate Motion 97 N (21.8 lbf) 280 N (63 lbf)
Maintain Motion (Opening) 53 N (12 lbf) 200 N (45 lbf) Maintain Motion (Closing) 58 N (13 lbf) 200 N (45 lbf)
Locks / Latches 26 N (5.9 lbf) 100 N (22.5 lbf)
Note 1: The operating force results listed above represent the maximum force measured among all sash tested.
AIR LEAKAGE TESTING: (per ASTM E 283)
Test Results Allowable
Infiltration @ 300 Pa (6.24 psf) 1.3 L/s/m2 (0.26 cfm/ft2)
1.5 L/s/m2 (0.30 cfm/ft2)
Exfiltration @ 300 Pa (6.24 psf) 0.3 L/s/m2 (0.06 cfm/ft2)
0.5 L/s/m2 (0.10 cfm/ft2)
Note 2: The specimen tested meets (or exceeds) the performance levels specified in AAMA/WDMA/CSA 101/I.S.2/A440 for air leakage resistance.
WATER PENETRATION TESTING: (per ASTM E 331 and ASTM E 547)
Test Results Allowable 540 Pa
(11.28 psf) Pass No Leakage
Note 3: Water Penetration testing was performed without an insect screen.
Report No.: 1686.05-106-12 Report Date: 4/18/2019
Page 7 of 8
WWW.MOLIMO.NET
TEST RESULTS: (Continued)
UNIFORM LOAD TESTING: (per ASTM E 330)
Design Pressure Test Results Allowable Deflection measured at
the meeting rail +3600 Pa (+75.19 psf) -3600 Pa (-75.19 psf)
6.1 mm (0.24") 7.1 mm (0.28")
8.1 mm (0.32") 8.1 mm (0.32")
Structural Test Results Allowable
Permanent Set measured at the meeting rail
+5400 Pa (+112.78 psf) -5400 Pa (-112.78 psf)
0.5 mm (0.02") 0.3 mm (0.01")
2.8 mm (0.11") 2.8mm (0.11")
Note 4: All loads were held for 10 seconds.
Note 5: Tape and film were used to seal against air leakage. In our opinion, the tape and film did not influence the results of the test.
SECONDARY TESTING:
Test Results Allowable FORCED ENTRY RESISTANCE
per ASTM F 588 Type: A – Grade: 10 Pass No Entry
DEGLAZING per ASTM E 987
Operating Direction – 320 N (70 lbf) Remaining Direction – 230 N (50 lbf)
Pass Pass
Meets as stated Meets as stated
General Note: All testing was performed in accordance with reference test methods.
Report No.: 1686.05-106-12 Report Date: 4/18/2019
Page 8 of 8
WWW.MOLIMO.NET
A copy of this report, detailed drawings, datasheets, representative samples of test specimens, or other pertinent project documentation will be retained by Molimo, LLC for the entire test record retention period. At the end of this retention period, the service life of this report will expire. Results obtained are tested values and were secured by using the designated test methods. This test report does not constitute certification of this product nor an opinion or endorsement by this laboratory. It is the exclusive property of the client so named herein and relates only to the specimen(s) tested. This report may not be reproduced, except in full, without the written permission of Molimo, LLC. For MOLIMO, LLC: Lance Cunningham Michael D. Stremmel, P.E. Manager – Operations / Sales Senior Project Engineer MDS:jld Attachments (pages): This report is complete only when all attachments listed are included.
Appendix-A: Alteration Addendum (1) Appendix-B: Air Seal Location (1) Appendix-C: Photographs (1) Appendix-D: Drawings (4)
This report was produced from controlled document template MMO 00013, Rev 2, 8/28/2018.
Report No.: 1686.05-106-12
WWW.MOLIMO.NET
Appendix A
Alteration Addendum
No alterations were performed.
Report No.: 1686.05-106-12
WWW.MOLIMO.NET
Appendix B
Air Seal Location
Fenestration Product
Test Wall
Seal Between FenestrationProduct and Test Buck
Seal Between TestBuck and Test Wall
Test Buck
Report No.: 1686.05-106-12
WWW.MOLIMO.NET
Appendix C
Photographs
Photo No. 1
Wood Double Hung Window
Report No.: 1686.05-106-12
WWW.MOLIMO.NET
Appendix D
Drawings
Glass Stop Profile
Ext.
Exterior Prfile
11/16"
5/8"
Glass
Wood Species: Mahogany/Sapele
Exterior Finish: Primed & Painted ( 2 Coats each )
Interior Finish: Primed & Painted ( 2 Coats each )
Hardware :
Double Hung
- 2 5/8" Bronze Pulleys
- Locks: Phelps LKF18
- Sash Lift: Phelps LFM26
Outswing Casement :
- 3
1
2
" x 3
1
2
" Butt Hinges
- Handle Type: Temporary Construction Handle
For all units
- Weather Stripping Color: Brown
Window and Door Shedule
Type Description Qty. Drawing No.
Notes
1
2 1/4" DH window [Weight & Chain]
1 01
2
2 11/16" Open Out Single Casement
1 03
3 2 11/16" Fixed Transom 1 04
TOTAL # OF UNITS 3
ALL ELEVATIONS ARE VIEWED FROM EXTERIOR
Legend
F.H.
Frame Height
F.W.
Frame Width
O.F.H.
Overall Frame Height
O.F.W.
Overall Frame Width
S.W.
Sash Width
U.S.H.
Upper Sash Height
L.S.H.
Lower Sash Height
O.S.H.
Overall Sash Height
G.O.
Glass Opening
M.O.
Masonry Opening
R.O.
Rough Opening
D.O.
Daylight Opening
7/8" Insulated Glass comprised of:
- Outboard - 3/16" Single Pane Heat Strengthened
- Inboard - 3/16" Single Pane Heat Strengthened
- 7/16" Sightline
- 1/2" Aluminum Spacer, Color Brown
3/16" HEAT STRENGTHENED
3/16" HEAT STRENGTHENED
1/2" AIR SPACE
7/8"
3/1
6"
1 2
"
3/1
6"
7/16"
Exterior
11/16"
5/8"
Scale:
Project No:
Date:
Drawn by:
Drawing No:
Revision:
04
/1
8/1
9K
J
Updated S
eries N
um
bers
A
Re
v:
De
scrip
tio
n:
By:
Da
te
:
Drawings and designs are the exclusive
property of Revival Sash & Door, and are
submitted as confidential information in
connection with your inquiry. They must not be
used for any other purposes, nor can they be
copied or loaned without written permission.
Pro
je
ct:
S1
V.J.
10/04/18
AAMA TEST
AA
MA
G
atew
ay T
est
AW
55D
P
Prelim
inary D
raw
ings
x
REV
IVA
L SA
SHC
US
TO
M W
IND
OW
S &
DO
OR
S
135
East
57t
h St
reet
, 18
-131
, N
ew Y
ork,
NY
1002
2Te
l : (6
46)-8
44-3
929
1"=1"
Legend
F.H.
Frame Height
F.W.
Frame Width
O.F.H.
Overall Frame Height
O.F.W.
Overall Frame Width
S.W.
Sash Width
U.S.H.
Upper Sash Height
L.S.H.
Lower Sash Height
O.S.H.
Overall Sash Height
G.O.
Glass Opening
M.O.
Masonry Opening
R.O.
Rough Opening
D.O.
Daylight Opening
2 1/4"
2 1
/4
"
2 1/4"
2 1
/4
"
2 1/4"
2 1
/4
"
2 1/4"
2 1
/4
"
F.W.2 7/8"
1 1/4"
1 1/8"
1/8"
2" G.O.
O.F.W.
F.W.
7 1/16"
3/4"
2 7/16"
5/8"
2 7/16"
13/16"
S.W.
2 7/8"
1 1/4"
1 1/8"
1/8"
O.F.W.
S.W.
2 1/4"
SECTION: 01 SECTION: 02
2"G.O.
3/8"3/8"
7 1/16"
3/4"
2 7/16"
5/8"
2 7/16"
13/16"
2 1/4"
SASH STOPSASH STOP
Optional
Exterior Trim
Optional
Exterior Trim
3/16" HEAT STRENGTHENED
3/16" HEAT STRENGTHENED
1/2" AIR SPACE
3/16" HEAT STRENGTHENED
3/16" HEAT STRENGTHENED
1/2" AIR SPACE
Elevation Scale 3/4" = 1'-0"
SPECIFICATIONS:
TAG DH225-D
QUANTITY 1 UNIT
DESCRIPTION
2-1/4" DOUBLE HUNG
WEIGHT AND CHAIN
GLASS 7/8" INSULATING GLASS
JAMB DEPTH 7
1
16
"
SCREENS NONE
FINISH
PRIMED & PAINTED
(2 COATS EACH)
PULLEY 2
7
8
" PULLEY
LIFTS LFM26
LOCK LKF18
CHAIN # 45
WEIGHTS 2
1
4
" X 2
1
4
" STEEL
7" 7"
S.W.
57 1/2"
1 7
/3
2"
O.F.W.
65 3/4"
F.W.
60"
F
.H
.
99
"
2 9
/3
2"
O.S
.H
.
95
1
/2
"
1 1/4"
2 7/8" 2 7/8"
G.O.
53 1/2"
1 1/4"
2" 2"
U.S
.H
.
48
1
/8
"
G.O
44
1
3/1
6"
G.O
.
44
1
3/1
6"
L.S
.H
.
49
3
/8
"
3 1
/4
"
2"
1 5
/1
6"
1 5
/1
6"
1
1
2
1
3
2
4
2
5
2
2
4
9
10
11
12
13
1516
17
19
23
26
18
5200 Series
Scale:
Project No:
Date:
Drawn by:
Drawing No:
Revision:
Re
v:
De
scrip
tio
n:
By:
Da
te
:
Drawings and designs are the exclusive
property of Revival Sash & Door, and are
submitted as confidential information in
connection with your inquiry. They must not be
used for any other purposes, nor can they be
copied or loaned without written permission.
Pro
je
ct:
01
V.J.
10/04/18
AAMA TEST
AA
MA
G
atew
ay T
est
AW
55D
P
Prelim
inary D
raw
ings
x
REV
IVA
L SA
SHC
US
TO
M W
IND
OW
S &
DO
OR
S
135
East
57t
h St
reet
, 18
-131
, N
ew Y
ork,
NY
1002
2Te
l : (6
46)-8
44-3
929
1"=1"
04
/1
8/1
9K
J
Updated S
eries N
um
bers
A
Legend
F.H.
Frame Height
F.W.
Frame Width
O.F.H.
Overall Frame Height
O.F.W.
Overall Frame Width
S.W.
Sash Width
U.S.H.
Upper Sash Height
L.S.H.
Lower Sash Height
O.S.H.
Overall Sash Height
G.O.
Glass Opening
M.O.
Masonry Opening
R.O.
Rough Opening
D.O.
Daylight Opening
1 1/2
1 1/4"
1 1/8"
1 7
/32
"
3/3
2"
F.H
.
U.S
.H
.
2 9/32"
L.S
.H
.
F.H
.
1 5/16"
G.O
.
1 5/16"
G.O
.
U.S
.H
.
L.S
.H
.
F.H
.
8°
O.S
.H
.
O.S
.H
.
O.S
.H
.
2 3
/8
7 1/16"
3/4" 2 7/16" 5/8" 2 7/16" 13/16"
2 1/4"
7 1/16"
3/4" 2 7/16" 5/8" 2 7/16" 13/16"
2 1/4"
7 1/16"
3/4" 2 7/16" 5/8" 2 7/16" 13/16"
2 1/4"2 1/4"
SECTION: 03
SECTION: 04
SECTION: 05
3/8"
2 1/2
"
2"
G.O
.3 3/16
"G
.O
.
SASH STOP
SIDE VIEW
5/8"
2 5/1
6"
Optional
Exterior T
rim
SASH STOP
3/16" H
EA
T S
TR
EN
GT
HE
NE
D
3/16" H
EA
T S
TR
EN
GT
HE
NE
D
1/2" A
IR
S
PA
CE
3/16" H
EA
T S
TR
EN
GT
HE
NE
D
3/16" H
EA
T S
TR
EN
GT
HE
NE
D
1/2" A
IR
S
PA
CE
3/16" H
EA
T S
TR
EN
GT
HE
NE
D
3/16" H
EA
T S
TR
EN
GT
HE
NE
D
1/2" A
IR
S
PA
CE
3/16" H
EA
T S
TR
EN
GT
HE
NE
D
3/16" H
EA
T S
TR
EN
GT
HE
NE
D
1/2" A
IR
S
PA
CE
Optional
Exterior Trim
1
5
14
86
6
3
720
21
22
24
25
Scale:
Project No:
Date:
Drawn by:
Drawing No:
Revision:
Re
v:
De
scrip
tio
n:
By:
Da
te
:
Drawings and designs are the exclusive
property of Revival Sash & Door, and are
submitted as confidential information in
connection with your inquiry. They must not be
used for any other purposes, nor can they be
copied or loaned without written permission.
Pro
je
ct:
02
V.J.
10/04/18
AAMA TEST
AA
MA
G
atew
ay T
est
AW
55D
P
Prelim
inary D
raw
ings
x
REV
IVA
L SA
SHC
US
TO
M W
IND
OW
S &
DO
OR
S
135
East
57t
h St
reet
, 18
-131
, N
ew Y
ork,
NY
1002
2Te
l : (6
46)-8
44-3
929
1"=1"
04
/1
8/1
9K
J
Updated S
eries N
um
bers
A
2 1/4"
3"
6 9/16"
2 1/8"
5/8"
13/16"
7/8"
1 1
/8"
3 1
5/16"
1 1/2
"
7 5/16"
8. Applied check rail
1. Frame head
3. Sill
12. Sash stops
10. Weight box cover interior9. Weight box cover exterior
11. Parting strip
15. Plywood plenum 16. Plywood weight box cover
2. Jambs
4. Stile 5. Top Rail
7. Bottom Rail
14. Blind stop13. Glass Stop
2 1/4" Double Hung Window
Item # Part Number
Description Remarks/Supplier
1 --- Frame Head
Mahogany
2 --- Jamb
Mahogany
3 --- Sill
Mahogany
4 --- Stile
Mahogany
5 ---
Top rail Mahogany
6 --- Check rail
Mahogany
7 --- Bottom rail
Mahogany
8 ---
Applied check rail Mahogany
9 ---
Weight box cover exterior Mahogany
10 ---
Weight box cover interior Mahogany
11 ---
Parting strip Mahogany
12 ---
Sash stop Mahogany
13 ---
Glass stop Mahogany
14 ---
Blind stop Mahogany
15 --- Plenum
Plywood
16 ---
Weight box cover Plywood
17 Z-46-2625
2 5/8" Brass pulley, cast solid brass housing, round face
Rockwell
18 #45
Brass Chain / Brass plated steel T&S Perfection / Phelps
19 81094RK
Cast iron weight 2 1/4" x 2 1/4"
---
20 LFM26 Sash Lift mortised
Phelps
21
LKF18
Sash lock with spring action and narrow strike Phelps
LK381 Traditional sash lock
Phelps
LF281 Traditional sash lock
Phelps
22 W17
Sash weathertrip bulb at bottom rail
RCT
23 QEZD-100Frame and Sash weatherstrip Schlegel
24 WS15
Check rails weatherstrip
RCT
25 WS75 Check rail brush RCT
26 DOW 995 Structural silicone
DOW Corning
6. Check Rail
1 1/8"
5/8"
2"
6 9/16"
2 1/4"
2 1/4"
2 1/4"
11/16"
3/4"
2 1
1/16"
2 11/16"
4 3/8"
3/4"
1 3/4"
1/4"
2"
1/4"
7 1/16"
7/8"
5/8"
11/16"
Scale:
Project No:
Date:
Drawn by:
Drawing No:
Revision:
Re
v:
De
scrip
tio
n:
By:
Da
te
:
Drawings and designs are the exclusive
property of Revival Sash & Door, and are
submitted as confidential information in
connection with your inquiry. They must not be
used for any other purposes, nor can they be
copied or loaned without written permission.
Pro
je
ct:
02A
V.J.
10/04/18
AAMA TEST
AA
MA
G
atew
ay T
est
AW
55D
P
Prelim
inary D
raw
ings
x
REV
IVA
L SA
SHC
US
TO
M W
IND
OW
S &
DO
OR
S
135
East
57t
h St
reet
, 18
-131
, N
ew Y
ork,
NY
1002
2Te
l : (6
46)-8
44-3
929
1"=1"
04
/1
8/1
9K
J
Updated S
eries N
um
bers
A