Wood Boring Machine
-
Upload
royalaryans -
Category
Documents
-
view
221 -
download
0
Transcript of Wood Boring Machine
-
8/10/2019 Wood Boring Machine
1/41
1 | P a g e
A PROJECT REPORT ON
WOOD HOLE CUTTER AT VARIABLE
DIAMETERSUBITTED IN PARTIAL FULFILLMENT FOR AWARD OF DEGREE OF
BACHELOR OF TECHNOLOGY
IN
MECHANICAL ENGINEERING
BY
AJAY SHARMA(100741132776)
DAVINDER SINGH(100741132783)
DEEPAK DHIMAN(100741132784)
HEMANT GAUTAM(100741132793)
LOVEPREET SINGH(100741132806)
MANPREET SINGH(100741132808)
UNDER THE GUIDANCE OF
MR. SARBJIT SINGH
-
8/10/2019 Wood Boring Machine
2/41
2 | P a g e
DEPARTMENT OF MECHANICAL ENGINEERING
SRI SAI COLLEGE OF ENGINEERING & TECHNOLOGY
MANAWALA , AMRITSAR
DEC-2013
A PROJECT REPORT ON
WOOD HOLE CUTTER AT VARIABLE
DIAMETER
SUBITTED IN PARTIAL FULFILLMENT FOR AWARD OF DEGREE OF
BACHELOR OF TECHNOLOGY
IN
MECHANICAL ENGINEERING
-
8/10/2019 Wood Boring Machine
3/41
3 | P a g e
BY
AJAY SHARMA(100741132776)
DAVINDER SINGH(100741132783)
DEEPAK DHIMAN(100741132784)
HEMANT GAUTAM(100741132793)
LOVEPREET SINGH(100741132806)
MANPREET SINGH(100741132808)
UNDER THE GUIDANCE OF
MR. SARBJIT SINGH
-
8/10/2019 Wood Boring Machine
4/41
4 | P a g e
DEPARTMENT OF MECHANICAL ENGINEERING
SRI SAI COLLEGE OF ENGINEERING & TECHNOLOGY
MANAWALA , AMRITSAR
DEC-2013
ACKNOWLEDGEMENT
Aresearch owes its success from commencement to completion, to people involved with research
various stages. I acknowledge with due courtesy my regards to all the persons and sources consul
during the development of this project and preparation of this report.
I am grateful from the core of my heart to our guide Mr.Sarbjit singh for his valuable time, help
and motivation which kept me going to the fulfillment of this project.
Also, it gives me immense pleasure to express my profound gratitude and thankfulness to
Mr.S.K.Tandon to facilitate me with his experience, guidance and instructions to accomplish this
project successfully
AJAY SHARMA(100741132776)
DAVINDER SINGH(100741132783)
DEEPAK DHIMAN(100741132784)
HEMANT GAUTAM(100741132793)
-
8/10/2019 Wood Boring Machine
5/41
5 | P a g e
LOVEPREET SINGH(100741132806)
MANPREET SINGH(100741132808)
BRANCH:-B.Tech(ME)-7th
Sem
INTRODUCTION
WOOD HOLE CUTTER AT VARIABLE DIAMETER
Wood hole cutter is the process of increase the diameter of hole on the work piece by
using a cutting tool called Single Point cutting tool.The machine used for this is known as
wood hole cutter machine.
We desired a hole cutter machine which will automatically index the job and gives
automatic feed to the head. This machine is designed to perform holes at variable
diameters.Even though this is designed to a hole on circumference of a job, this can also
perform a number of similar operations like drilling, remaining, boring, counter boring,
counter sinking, tapping etc with slight alterations on the machine. Wood designed a hole
cutter machine which uses only mechanical principles. Therefore it is very easy for
maintenance and which improves the reliability of the machine.
A drilling machine, called a drill press, is used to cut holes into or through metal,
wood, or other materials.Drilling machines use a drilling tool that has cutting edges at its
point. This cutting tool is held in the drill press by a chuckor Morse taper and is rotated
and fed into the work at variable speeds. Drilling machines may be used to perform other
operations. They can perform countersinking, boring, counterboring, spot facing,
reaming, and tapping .Drill press operators must know how to set up the work, set speed
and feed, and provide for coolant to get an acceptable finished product.
In machining, boring is the process of enlarging a hole that has already been drilled (or
cast), by means of a single-point cutting tool (or of a boring head containing several such
tools), for example as in boring a gun barrel or an engine cylinder. Boring is used to
achieve greater accuracy of the diameter of a hole, and can be used to cut a tapered hole.
Boring can be viewed as the internal-diameter counterpart to turning, which cuts external
diameters.
There are various types of boring. The boring bar may be supported on both ends (which
only works if the existing hole is a through hole), or it may be supported at one end
(which works for both through holes and blind holes. Line boring (line boring, line-
boring) implies the former. Backboring (back boring, back-boring) is the process of
-
8/10/2019 Wood Boring Machine
6/41
6 | P a g e
reaching through an existing hole and then boring on the "back" side of the workpiece
(relative to the machine headstock).
Because of the limitations on tooling design imposed by the fact that the workpiece
mostly surrounds the tool, boring is inherently somewhat more challenging than turning,
in terms of decreased tool holding rigidity, increased clearance angle requirements
(limiting the amount of support that can be given to the cutting edge), and difficulty of
inspection of the resulting surface (size, form, surface roughness). These are the reasons
why boring is viewed as an area of machining practice in its own right, separate from
turning, with its own tips, tricks, challenges, and body of expertise, despite the fact that
they are in some ways identical.
FEED RATE
Feed rate is the velocity at which the cutter is fed, that is, advanced against the workpiece. It is
expressed in units of distance per revolution for turning and boring (typically inches per
revolution[ipr] or millimeters per revolution). It can be expressed thus for milling also, but it is
often expressed in units of distance per time for milling (typically inches per minute[ipm] or
millimeters per minute), with considerations of how many teeth (or flutes) the cutter has then
determining what that means for each tooth.
Feed rate is dependent on the:
Type of tool (a small drill or a large drill, high speed or carbide, a box tool or recess, a
thin form tool or wide form tool, a slide knurl or a turret straddle knurl).
Surface finish desired.
Power available at the spindle (to prevent stalling of the cutter or workpiece).
Rigidity of the machine and tooling setup (ability to withstand vibration or chatter).
Strength of the workpiece (high feed rates will collapse thin wall tubing)
Characteristics of the material being cut, chip flow depends on material type and feed
rate. The ideal chip shape is small and breaks free early, carrying heat away from the
tool and work.
DEPTH OF CUT:
Cutting speed and feed rate come together with depth of cut to determine the material
removal rate, which is the volume of workpiece material (metal, wood, plastic, etc.) that
can be removed per time unit.
-
8/10/2019 Wood Boring Machine
7/41
7 | P a g e
GENERAL DRILLING OPERATIONS
After a workpiece is laid out and properly mounted, the drilling process can begin. The drilling
process, or complete operation, involves selecting the proper twist drill or cutter forthe job,
properly installing the drill into the machine spindle,setting the speed and feed, starting the hole
on center, and drilling the hole to specifications within the prescribed tolerance. Tolerance is the
allowable deviation from standard size. The drilling process must have some provisions for
tolerance because of the oversizing that naturally occurs in drilling. Drilled holes are always
slightly oversized, or slightly larger than the diameter of the drills original designation. For
instance, a l/4-inch twist drill will produce a hole that may be several thousandths of an inchlarger than l/4-inch.
A drill is a tool fitted with a cutting tool attachment or driving tool attachment, usually a drill bit
or driver bit, used for drilling holes in various materials or fastening various materials together
with the use of fasteners. The attachment is gripped by a chuck at one end of the drill and
rotated while pressed against the target material. The tip, and sometimes edges, of the cutting
tool does the work of cutting into the target material. This may be slicing off thin shavings (twist
-
8/10/2019 Wood Boring Machine
8/41
8 | P a g e
drills or auger bits), grinding off small particles (oil drilling), crushing and removing pieces of the
workpiece (SDS masonry drill), countersinking, counterboring, or other operations.
-
8/10/2019 Wood Boring Machine
9/41
9 | P a g e
DRILL PRESS
A drill press (also known as pedestal drill, pillar drill, or bench drill) is a fixed style of
drill that may be mounted on a stand or bolted to the floor or workbench. Portable models
with a magnetic base grip the steel workpieces they drill. A drill press consists of a base,column (or pillar), table, spindle (or quill), and drill head, usually driven by an induction
motor. The head has a set of handles (usually 3) radiating from a central hub that, when
turned, move the spindle and chuck vertically, parallel to the axis of the column. The
table can be adjusted vertically and is generally moved by a rack and pinion; however,
some older models rely on the operator to lift and reclamp the table in position. The table
may also be offset from the spindle's axis and in some cases rotated to a position
perpendicular to the column. The size of a drill press is typically measured in terms of
swing. Swing is defined as twice the throat distance, which is the distance from the
center of the spindle to the closest edge of the pillar. For example, a 16-inch (410 mm)
drill press has an 8-inch (200 mm) throat distance.
A drill press has a number of advantages over a hand-held drill:
Less effort is required to apply the drill to the workpiece. The movement of the chuck
and spindle is by a lever working on a rack and pinion, which gives the operator
considerable mechanical advantage
-
8/10/2019 Wood Boring Machine
10/41
10 | P a g e
The table allows a vise or clamp to be used to position and restrain the work, making
the operation much more secure
The angle of the spindle is fixed relative to the table, allowing holes to be drilled
accurately and consistently
Drill presses are almost always equipped with more powerful motors compared to
hand-held drills. This enables larger drill bits to be used and also speeds up drilling with
smaller bits.
For most drill pressesespecially those meant for woodworking or home usespeed
change is achieved by manually moving a belt across a stepped pulley arrangement.
Some drill presses add a third stepped pulley to increase the number of available speeds.
Modern drill presses can, however, use a variable-speed motor in conjunction with the
stepped-pulley system. Medium-duty drill presses such as those used in machine shop
(tool room) applications are equipped with a continuously variable transmission. This
mechanism is based on variable-diameter pulleys driving a wide, heavy-duty belt. This
gives a wide speed range as well as the ability to change speed while the machine is
running. Heavy-duty drill presses used for metalworking are usually of the gear-head
type described below.
Drill presses are often used for miscellaneous workshop tasks other than drilling holes.
This includes sanding, honing, and polishing. These tasks can be performed by mounting
sanding drums, honing wheels and various other rotating accessories in the chuck. This
can be unsafe in some cases, as the chuck arbor, which may be retained in the spindle
solely by the friction of a taper fit, may dislodge during operation if the side loads are too
high.
TWIST DRILL
Twist drills are the most common cutting tools used with drilling machines. Twist drills are
designed to make round holes quickly and accurately in all materials. They are called
twist drills mainly because of the helical flutes or grooves that wind around the body from the
point to the neck of the drill and appear to be twisted. Twist drills are simply constructed but
designed very tough to withstand the high torque of turning, the downward pressure on the
drill, and the high heat generated by friction.
There are two common types of twist drills, high-speed steel drills, and carbide-tipped drills. The
most common type used for field and maintenance shop work is the high-speed steel twist drill
because of its low cost. Carbide-tipped metal drills are used in production work where the drill
must remain sharp for extended periods, such as in a numerically controlled drilling machine.
Other types of drills available are: carbide tipped masonry drills, solid carbide drills, TiN coated
drills, parabolic drills and split point drills. Twist drills are classified as straight shank or tapered
-
8/10/2019 Wood Boring Machine
11/41
11 | P a g e
shank. Straight shank twist drills are usually l/2-inch or smaller and tit into geared drill chucks,
while tapered shank drills are usually for the larger drills that need more strength which is
provided by the taper socket chucks.
Common twist drill sizes range from 0.0135 to 3.500 inches in diameter. Larger holes are cut by
special drills that are not considered as twist drills. The standard sizes used in the United Statesare the wire gage numbered drills, letter drills, fractional drills, and metric drill.Twist drills can
also be classified by the diameter and length of the shank and by the length of the fluted portion
of the twist drill.
-
8/10/2019 Wood Boring Machine
12/41
12 | P a g e
CHARACTERSTICS
All drilling machines have the following construction characteristics: a spindle. sleeve or quill.
column, head, worktable, and base.
The spindle holds the drill or cutting tools and revolves in a fixed position in a sleeve. In
most drilling machines, the spindle is vertical and the work is supported on a horizontal
table.
The sleeve or quill assembly does not revolve but may slide in its bearing in a direction
parallel to its axis.When the sleeve carrying the spindle with a cutting tool is lowered,
the cutting tool is fed into the work: and when it is moved upward, the cutting tool is
withdrawn from the work. Feed pressure applied to the sleeve by hand or power causes
the revolving drill to cut its way into the work a few thousandths of an inch per
revolution.
The column of most drill presses is circular and built rugged and solid. The column
supports the head and the sleeve or quill assembly.
The head of the drill press is composed of the sleeve,spindle, electric motor, and feed
mechanism. The head isbolted to the column.
The worktable is supported on an arm mounted to the column. The worktable can be
adjusted vertically to accommodate different heights of work. or it may be swung
-
8/10/2019 Wood Boring Machine
13/41
13 | P a g e
completely out of the way. It may be tilted up to 90 in either direction, to allow for long
pieces to be end or angled drilled.
The base of the drilling machine supports the entire machine and when bolted to the
floor, provides for vibration-free operation and best machining accuracy.The top of the
base is similar to a worktable and maybeequipped with T-slots for mounting work too
large for the table.
USES
A drilling machine, called a drill press, is used to cut holes into or through metal, wood, or other
materials.Drilling machines use a drilling tool that has cutting edges at its point. This cutting tool
is held in the drill press by a chuck or Morse taper and is rotated and fed into the work at
variable speeds. Drilling machines may be used to perform other operations. They can perform
countersinking, boring, counterboring, spot facing, reaming, and tapping.Drill press operators
must know how to set up the work, set speed and feed, and provide for coolant to get anacceptable finished product. The size or capacity of the drilling machine
is usually determined by the largest piece of stock that can be center-drilled. For instance, a 15-
inch drilling machine can center-drill a 30-inch-diameter piece of stock.Other ways to determine
the size of the drill press are by the
largest hole that can be drilled, the distance between the spindle and column, and the vertical
distance between the worktable and spindle.
WORKING PRINCIPLE
The principle of operation of this machine is explained under three sub headings.
1.
Driving mechanism
2.
Feed mechanism
3.
Indexing mechanism
-
8/10/2019 Wood Boring Machine
14/41
14 | P a g e
1.
DRIVING MECHANISM:
In driving mechanisms a single-phase AC motor is used for driving the whole machine. Though
the speed of the motor is less, it can carry more loads on it. Power of the motor is 0.50 hp. The
rotary motion of the motor is transmitted to the worm gear in the gearbox by chain andsprocket mechanism. A wheel is aligned to the worm gear and the motion is transmitted.
2.
FEED MECHANISM:
One side of the wheel inside the gearbox connected to the crank disc. Main function of the
crank disc is to convert the rotary motion into linear vertical motion to get vertical feed for
Boring head. A link mechanism in a lever connects crank disc and hand drilling machine. It helps
to transmit vertical feed to the hand Boring machine.
3.
INDEXING MECHANISM:
From the wheel with the help of link mechanism, motion is transmitted to an arm to which
pawl-1 is connected. The movement of pawl is in such a way that it will push.
-
8/10/2019 Wood Boring Machine
15/41
-
8/10/2019 Wood Boring Machine
16/41
16 | P a g e
Power of motor:-
The AC motor used in our project is 0.50 hp(horse power).The diameter ofpulley attached to the shaft of the motor is 2 inch.The speed of motor is 600 rpm.The
power is transmitted with the help of rubber belt.The number of belt used to rotate thedrill chuck is 37A. A universal motor is a single-phase series motor, which is able to run
on either alternating current (ac) or direct current (dc) and the characteristics are similar
for both ac and dc. The field windings of a series motors are connected in series with the
armature windings. The electrical design areas of a universal motor are the magneticcircuit, the field and armature windings, the commutator and brushes, the insulation and
the cooling system. An electric motor is an electric machine that converts electrical
energy into mechanical energy.
In normal motoring mode, most electric motors operate through the interaction between
an electric motor's magnetic field and winding currents to generate force within themotor. In certain applications, such as in the transportation industry with traction motors,
electric motors can operate in both motoring and generating or braking modes to also
produce electrical energy from mechanical energy.
Found in applications as diverse as industrial fans, blowers and pumps, machine tools,
household appliances, power tools, and disk drives, electric motors can be powered by
direct current (DC) sources, such as from batteries, motor vehicles or rectifiers, or byalternating current (AC) sources, such as from the power grid, inverters or generators.
Small motors may be found in electric watches. General-purpose motors with highly
standardized dimensions and characteristics provide convenient mechanical power forindustrial use. The largest of electric motors are used for ship propulsion, pipeline
compression and pumped-storage applications with ratings reaching 100 megawatts.
-
8/10/2019 Wood Boring Machine
17/41
17 | P a g e
Electric motors may be classified by electric power source type, internal construction,
application, type of motion output, and so on.
Devices such as magnetic solenoids and loudspeakers that convert electricity into motion
but do not generate usable mechanical power are respectively referred to as actuators and
transducers. Electric motors are used to produce linear force or torque (rotary).
RADIAL DRILLING MACHINE
-
8/10/2019 Wood Boring Machine
18/41
18 | P a g e
Introduction
-
8/10/2019 Wood Boring Machine
19/41
19 | P a g e
Drilling machine is one of the most important machine tools in a workshop. It was
designed to produce a cylindrical hole of required diameter and depth on metal
workpieces.Though holes can be made by different machine tools in a shop, drilling machine is
designed specifically to perform the operation of drilling and similar operations. Drilling
can be done easily at a low cost in a shorter period of time in a drilling machine.Drilling can be called as the operation of producing a cylindrical hole of requireddiameter and depth by removing metal by the rotating edges of a drill.
The cutting tool known as drill is fitted into the spindle of the drilling machine. A mark
of indentation is made at the required location with a center punch. The rotating drill ispressed at the location and is fed into the work. The hole can be made upto a required
depth.
Construction of a drilling machineThe basic parts of a drilling machine are a base, column, drill head and spindle.
The base made of cast iron may rest on a bench, pedestal or floor depending upon the
design. Larger and heavy duty machines are grounded on the floor. The column ismounted vertically upon the base. It is accurately machined and the table can be moved
up and down on it. The drill spindle, an electric motor and the mechanism meant fordriving the spindle at different speeds are mounted on the top of the column. Power is
transmitted from the electric motor to the spindle through a flat belt or a V belt.
Types of drilling machinesDrilling machines are manufactured in different types and sizes according to the type of
operation, amount of feed, depth of cut, spindle speeds, method of spindle movement andthe required accuracy.
The different types of drilling machines are:
1. Portable drilling machine (or) Hand drilling machine2. Sensitive drilling machine (or) Bench drilling machine
3. Upright drilling machine
4. Radial drilling machine
5. Gang drilling machine6. Multiple spindle drilling machine
7. Deep hole drilling machine
Portable drilling machine
Portable drilling machine can be carried and used anywhere in the workshop. It is usedfor drilling holes on workpieces in any position, which is not possible in a standard
drilling machine. The entire drilling mechanism is compact and small in size and so canbe carried anywhere. This type of machine is widely adapted for automobile built-up
work. The motor is generally universal type. These machines can accommodate drills
from 12mm to 18 mm diameter. Portable drilling machines are operated at higher speeds.
Sensitive drilling machine
-
8/10/2019 Wood Boring Machine
20/41
20 | P a g e
It is designed for drilling small holes at high speeds in light jobs. High speed and hand
feed are necessary for drilling small holes. The base of the machine is mounted either on
a bench or on the floor by means of bolts and nuts. It can handle drills upto 15.5mm ofdiameter. The drill is fed into the work purely by hand . The operator can sense the
progress of the drill into the work because of hand feed. The machine is named so
because of this reason. A sensitive drilling machine consists of a base, column, table,spindle, drill head and the driving mechanism.A sensitive drilling machine is shown in Fig. 2.1.
BaseThe base is made of cast iron and so can withstand vibrations. It may be mounted on a
bench or on the floor. It supports all the other parts of the machine on it.
ColumnThe column stands vertically on the base at one end. It supports the work table and the
drill head. The drill head has drill spindle and the driving motor on either side of the
column.
Table
The table is mounted on the vertical column and can be adjusted up and down on it.The table has T-slots on it for holding the workpieces or to hold any other work holding
device. The table can be adjusted vertically to accommodate workpieces of different
heights and can be clamped at the required position.
Drill head
-
8/10/2019 Wood Boring Machine
21/41
21 | P a g e
Drill head is mounted on the top side of the column. The drill spindle and the driving
motor are connected by means of a V-belt and cone pulleys. The motion is transmitted to
the spindle from the motor by the belt. The pinion attached to the handle meshes with therack on the sleeve of the spindle for providing the drill the required downfeed. There is
no power feed arrangement in this machine. The spindle rotates at a speed ranging from
50 to 2000 r.p.m.
Sensitive drilling machineBaseColumn
Electric motorV belt
TableSpindleSleeveDrill headFeed handle
Stepconepulley
Upright drilling machineThe upright drilling machine is designed for handling medium sized workpieces.Though it looks like a sensitive drilling machine, it is larger and heavier than a sensitive
drilling machine. Holes of diameter upto 50mm can be made with this type of machine.
Besides, it is supplied with power feed arrangement. For drilling different types of work,
the machine is provided with a number of spindle speeds and feed.
-
8/10/2019 Wood Boring Machine
22/41
22 | P a g e
There are two different types of upright drilling machines according to the cross-sectionof the column and they are
1. Round column section upright drilling machine
2. Box column section upright drilling machine
A round column section upright drilling machine is shown in Fig. 2.2.The main parts of a upright drilling machine are : base, column, table and drill head.
BaseBase is made of cast iron as it can withstand vibrations set by the cutting action. It is
erected on the floor of the shop by means of bolts and nuts. It is the supporting member
as it supports column and other parts on it. The top of the base is accurately machinedand has T-slots. When large workpieces are to be held, they are directly mounted on the
base.
-
8/10/2019 Wood Boring Machine
23/41
23 | P a g e
ColumnColumn stands vertically on the base and supports the work table and all driving
mechanisms. It is designed to withstand the vibrations set up due to the cutting action athigh speeds.
TableTable is mounted on the column and can be adjusted up and down on it. It is providedwith T-slots for workpieces to be mounted directly on it. Table may have the following
adjustments
(i) Vertical adjustment obtained by the rack on the column and a pinion in the table(ii) Circular adjustment about its own axis
After the required ajustments are made, the table is clamped in position.
Drill headThe drillhead is mounted on the top of the column. It houses the driving and feeding
mechanism of the spindle. The spindle can be provided with hand or power feed . There
are separate hand wheels for quick hand feed and sensitive hand feed. The handle isspring loaded so that the drill spindle is released from the work when the operation is
over.
Radial drilling machineThe radial drilling machine is intended for drilling on medium to large and heavy
workpieces. It has a heavy round column mounted on a large base. The column supportsa radial arm, which can be raised or lowered to enable the table to accommodate
workpieces of different heights. The arm, which has the drilllhead on it, can be swung
around to any position. The drill head can be made to slide on the radial arm. The
machine is named so because of this reason. It consists of parts like base, column, radial
arm, drillhead and driving mechanism.A radial drilling machine is illustrated in Fig. 2.3
-
8/10/2019 Wood Boring Machine
24/41
24 | P a g e
BaseThe base is a large rectangular casting and is mounted on the floor of the shop. Its top is
accurately finished to support a column at one end and the table at the other end. T -slotsare provided on it for clamping workpieces.
ColumnThe column is a cylindrical casting, which is mounted vertically at one end of the base.It supports the radial arm and allows it to slide up and down on its face. The vertical
adjustment of the radial arm is effected by rotating a screw passing through a nut attached
to the arm. An electric motor is mounted on the top of the column for rotating theelevating screw.
Radial arm
The radial arm is mounted on the column parallel to the base and can be adjustedvertically. The vertical front surface is accurately machined to provide guideways for the
drillhead. The drillhead can be adjusted along these guideways according to the location
of the work. In some machines, a separate motor is provided for this movement. The armmay be swung around the column. It can also be moved up and down to suit workpieces
of different heights.
DrillheadThe drillhead is mounted on the radial arm and houses all mechanism for driving the drill
at different speeds and at different feed. A motor is mounted on top of the drillhead for
this purpose. To adjust the position of drill spindle with respect to the work, the drillheadmay be made to slide on the guideways of the arm. The drillhead can be clamped in
position after the spindle is properly adjusted.
Universal radial drilling machineIt is a machine in which the spindle can be swiveled to any required angle in vertical and
horizontal positions.
Gang drilling machineGang drilling machine has a long common table and a base. Four to six drillheads areplaced side by side. The drillheads have separate driving motors. This machine is used for
production work.
A series of operations like drilling, reaming, counterboring and tapping may beperformed on the work by simply shifting the work from one position to the other on the
work table. Each spindle is set with different tools for different operations.
Fig.2.4 shows a gang drilling machine.
-
8/10/2019 Wood Boring Machine
25/41
-
8/10/2019 Wood Boring Machine
26/41
26 | P a g e
machine, power input are also needed to specify the machine completely. The size of the
radial drilling machine is specified by the diameter of the column and length of the
radical arm.
Drill spindle assembly
A drill spindle assembly is illustrated in Fig. 2.5. The drill spindle is a vertical shaft,which holds the drill. A long keyway is cut on the spindle and a sliding key connects it
with a bevel gear or a stepped cone pulley. It receives motion from the driving motor.
The spindle rotates within a non-rotating sleeve known as quill. The spindle and thesleeve are connected by a thrust bearing.
Rack teeth are cut on the outer surface of the quill. The sleeve (quill) may be moved up
and down by rotating a pinion which meshes with the rack. This movement is given to
the spindle for providing the required feed. As there is a long keyway on top of thespindle, it is connected to the driving mechanism even during the feed movement.
A morse taper hole is provided at the lower end of the spindle. It is useful in
accommodating a taper shank drill. The tang of the drill fits into a slot provided at the endof the taper hole. To remove the drill from the spindle a drift may be pushed through theslot.
The spindle drive is obtained in three methods. They are:
1. Step cone pulley drive2. Step cone pulley with back gear arrangement
3. Gear box drive
-
8/10/2019 Wood Boring Machine
27/41
27 | P a g e
Work holding devicesThe work should be held firmly on the machine table before performing any operation on
it. As the drill exerts very high quantity of torque while rotating, the work should not beheld by hand. If the workpiece is not held by a proper holding device, it will start rotating
along with the tool causing injuries to the operator and damage to the machine.
The devices used for holding the work in a drilling machine are1. Drill vise
2. T - bolts and clamps
3. Step block4. V - block
5. Angle plate
6. Drill jigs
Drill viseVise is one of the important devices used for holding workpices on a drilling machinetable. The work is clamped in a vise between a fixed jaw and a movable jaw.
Parallel blocks are placed below the work so that the drill may completely pass throughthe work without damaging the table. Different types of vises are used for holding
different types of work and for performing different operations.The different types of vises are
1. Plain vise
2. Swivel vise3. Tilting vise
4. Universal vise
A plain vise is shown in Fig. 2.6.
T- bolts and clampsThe workpieces can be held directly on the machine table by means of T - bolts
andclamps. The top of the machine table has T - slots into which T - bolts may befitted. The bolts of diameter 15 to 20mm are used. The clamps are made of mild steel. T
- bolts pass through a central hole on the clamp. The clamp is made to rest horizontally
on the work surface by placing a suitable step block at the other end of the work.Some of the common types of clamps are: Plain slot clamp, goose-neck clamp and finger
clamp.Fig. 2.7 illustrates T - bolt and a clamp.
-
8/10/2019 Wood Boring Machine
28/41
28 | P a g e
Step blocks
The step blocks are used in combination with T- bolts and clamps for holding the workdirectly on the table. The step block supports the other end of the clamp. Workpieces ofdifferent heights are held by leveling the clamp on different steps of the step block.Fig.2.8 illustrates a stepblock.
V - blockV - blocks are used for holding cylindrical workpieces. The work may be supported ontwo or three V - blocks according to the length of the work. The work is held on the
V groove and is clamped by straps and bolts. They are made of cast iron or steel and areaccurately machined.Fig. 2.9 shows the use of a V - block.
-
8/10/2019 Wood Boring Machine
29/41
29 | P a g e
Angle plateAngle plates have two faces at right angle to each other and are made of cast iron.
It resembles the English alphabet L. All the sides of a angle plate are machined
accurately.Slots and holes are provided on both the faces of the angle plate. Work is clamped on one
of its faces by means of bolts and nuts. The use of an angle plate is shown in Fig. 2.10
Drill JigDrill jigs are used in mass production process. A jig is specially designed to hold the
work securely and to guide the tool at any desired position. Holes may be drilled at thesame relative positions on each of the identical workpieces.
The work is clamped and removed easily. The cost of making a drill jig is more but a low
order of skill is sufficient to work with a drill jig.Fig 2.11 illustrates a drill jig.
-
8/10/2019 Wood Boring Machine
30/41
30 | P a g e
Different types of drill jigs are
1. Plate jig 4. Box jig
2. Channel jig 5. Indexing jig.3. Diameter jig
Tools used in a drilling machineDifferent tools are used for performing different types of operations. The most commonly
used tools in a drilling machine are
1. Drill2. Reamer
3. Counterbore
4. Countersink5. Tap
DrillA drill is a tool used to originate a hole in a solid material. A helical groove known as
flute is cut along the length of the drill.Different types of drills are
1. Flat Drill
2. Straight fluted drill
3. Twist drill4. Centre drill
Twist drills are the type generally used in shop work. They are made of High speed steel
(HSS) or High carbon steel.There are two types of twist drills namely (i) Straight shank twist drill and (ii) Taper
shank twist drill. The diameter of the straight shank drill ranges from 2 to 16mm. Taper
shanks are provided on drills of larger diameter.
-
8/10/2019 Wood Boring Machine
31/41
31 | P a g e
ReamerThe tool used for enlarging and finishing a previously drilled hole is known as a reamer.
It is a multi tooth cutter and removes smaller amount of material. It gives a better fnishand accurate dimension.
CounterboreA Counterbore is a multi tooth cutting tool used for enlarging the top of the previously
machined hole. It has three or four cutting teeth.The flutes on them may be straight or helical. Straight fluted tools are used for machining
softer materials like brass and aluminium and for short depth of cut. Helical fluted
counterbores are used for longer holes.
CountersinkA countersink has cutting edges on its conical surfaces. It has a similar construction ofa counterbore except for the angle of the cutting edges.The angle of countersinks will
generally be 60, 82 or 90. It is used for enlarging the top of the holes conically.
TapA tap has threads like a bolt.It has three to four flutes cut across the threads. It can cutthreads on the inside of a hole. The flutes on the threads form the cutting edges. It is a
multi point cutting tool. It will dig into the walls of the hole as the lower part of the tap is
slightly tapered. The shank of the tap is square shaped to enable it to be held by a tapwrench.
Twist drill nomenclatureAxis
It is the longitudinal centerline of the drill running through the centres of the tang and thechisel edge.
Body
It is the part of the drill from its extreme point to the commencement of the neck, ifpresent. Otherwise, it is the part extending upto the commencement of the shank. Helical
grooves are cut on the body of the drill.
ShankIt is the part of the drill by which it is held and driven. It is found just above the body of
the drill. The shank may be straight or taper. The shank of the drill can be fitted directly
into the spindle or by a tool holding device.
Tang
The flattened end of the taper shank is known as tang. It is meant to fit into a slot in the
spindle or socket. It ensures a positive drive of the drill.
-
8/10/2019 Wood Boring Machine
32/41
32 | P a g e
NeckIt is the part of the drill, which is diametrically undercut between the body and the shank
of the drill. The size of the drill is marked on the neck.
Point
It is the sharpened end of the drill. It is shaped to produce lips, faces, flanks and chiseledge.
Lip
It is the edge formed by the intersection of flank and face. There are two lips and bothof them should be of equal length. Both lips should be at the same angle of inclination
with
the axis (59).
-
8/10/2019 Wood Boring Machine
33/41
33 | P a g e
LandIt is the cylindrically ground surface on the leading edges of the drill flutes adjacent to the
body clearance surface. The alignment of the drill is maintained by the land. The hole ismaintained straight and to the right size.
FlutesThe grooves in the body of the drill are known as flutes. Flutes form the cutting edges onthe point. It allows the chips to escape and make them curl. It permits the cutting fluid to
reach the cutting edges.
Angles
Chisel edge angleThe obtuse angle included between the chisel edge and the lip as viewed from the end of
the drill. It usually ranges from 120 to 135.
Helix angle or rake angleThe helix or rake angle is the angle formed by the leading edge of the land with a plane
having the axis of the drill. If the flute is straight, parallel to the drill axis, then there
would be no rake. If the flute is right handed, then it is positive rake and the rake isnegative if it is left handed. The usual value of rake angle is 30 or 45.
Point angleThis is the angle included between the two lips projected upon a plane parallel to the drill
axis and parallel to the two cutting lips. The usual point angle is 118. When hard alloys
are drilled the value increases.
Lip clearance angleThe angle formed by the flank and a plane at right angles to the drill axis. The angle is
normally measured at the periphery of the drill. The lip clearance angle ranges from 12to 15.
Tool holding devicesDifferent tools are used for performing different operations. They are fitted into the drill
spindle by different methods. They are1. By directly fitting in the spindle
2. By a sleeve
3. By a socket4. By a chuck5. Tapping attachment
-
8/10/2019 Wood Boring Machine
34/41
34 | P a g e
SpindleAlmost all drilling machines have their spindle bored out to a standard taper(1:20) to
receive the taper shank of the tool. While fitting the tool, the shank of the drill (or anyother tool) is forced into the tapered hole and the tool is gripped by friction. The tool may
be rotated with the spindle by friction between the tapered surface and the spindle. But to
ensure a positive drive, the tang of the tool fits into a slot at the end of the taper hole. Thetool may be removed by pressing a tapered wedge known as drift into the slotted hole of
the spindle.
SleeveThe drill spindle is suitable for holding only one size of tool shank. If the shank of thetool is smaller than the taper in the spindle hole, a taper sleeve is used. The outside taper
of the sleeve conforms to the spindle taper and the inside taper holds the shanks of the
smaller size tools. The sleeve has a flattened end or tang which fits into the slot of the
spindle. The tang of the tool fits into a slot provided at the end of the taper hole of thesleeve. Different sizes of tool shanks may be held by using different sizes of sleeve. In
order to remove the drill from the spindle, the drill along with the sleeve is removed withthe help of a drift. The drill is then removed from the sleeve by the same method.
-
8/10/2019 Wood Boring Machine
35/41
35 | P a g e
SocketDrill sockets are much longer in size than the drill sleeves. A socket consists of a solid
shank attached to the end of a cylindrical body. The taper shank of the socket conforms tothe taper of the drill spindle and fits into it. The body of the socket has a tapered hole
larger than the drill spindle taper into which the taper shank of any tool may be fitted.
The tang of the socket fits into slot of the spindle and the tang of the tool fits slot of thesocket.
Fig. 2.14 illustrates a socket.
Drill chuckThis type of chuck is particularly adapted for holding tools having straight shanks. Thedrill chuck has a taper shank which fits into the taper hole of the spindle. The jaws fitted
in the body of the chuck holds the straight shank drills.Fig. 2.15 illustrates a drill chuck.
Tapping attachmentThe tapping attachment is used to hold the tool known as tap. It serves as a flexibleconnection between the spindle and the tap. The taper shank of the attachment is fitted
into the drill spindle. The tap is fitted at the bottom of the attachment. The tap is fed into
the specific hole by the spindle, rotating it in clockwise direction. After the threads arecut, the spindle is released from the hole. The bottom of the attachment rotates in anti-clockwise direction causing no damage to the tapped hole. Tapping attachments are used
during production work.Fig. 2.16 illustrates a tapping attachment.
-
8/10/2019 Wood Boring Machine
36/41
36 | P a g e
Drilling machine operationsThough drilling is the primary operation performed in a drilling machine, a number of
similar operations are also performed on holes using different tools. The differentoperations that can be performed in a drilling machine are:
1. Drilling
2. Reaming3. Boring
4. Counter boring
5. Countersinking6. Spot facing
7. Tapping
8. Trepanning
DrillingDrilling is the operation of producing a cylindrical hole of required diameter and depth byremoving metal by the rotating edge of a cutting tool called drill. Drilling is one of the
simplest methods of producing a hole. Drilling does not produce an accurate hole in aworkpiece. The internal surface of the hole generated by drilling becomes rough and the
hole is always slightly oversize due to vibration of the spindle and the drill. A hole madeby a drill of size 12mm will measure approximately upto 12.125mm and by a drill of size
22mm will measure upto 22.5mm.Fig. 2.17 illustrates drilling operation.
-
8/10/2019 Wood Boring Machine
37/41
-
8/10/2019 Wood Boring Machine
38/41
38 | P a g e
Boring tool is a tool with only one cutting edge. The tool is held in a boring bar which
has a taper shank to fit into the spindle or a socket. For perfectly finishing a hole, the job
is drilled undersize slightly. Boring operation in some precise drilling machine isperformed to enlarge the holes to an accuracy of 0.00125mm. The spindle speed during
boring should be adjusted to be lesser than that of reaming. Fig. 2.19 illustrates boring
operation.
CounterboringCounterboring is the operation of enlarging the end of the hole cylindrically. Theenlarged hole forms a square shoulder with the original hole. This is necessary in some
cases to accommodate the heads of bolts, studs and pins. The tool used for counter boring
is known as counter bore.The counterbores are made with cutting edges which may be straight or spiral. The
cutting speed for counterboring is atleast 25% lesser than that of drilling.
-
8/10/2019 Wood Boring Machine
39/41
39 | P a g e
CountersinkingCountersinking is the operation of making a cone shaped enlargement at the end of thehole. The included angle of the conical surface may be in the range of 60 to 90. It is
used to provide recess for a flat headed screw or a counter sunk rivet fitted into the hole.The tool used for counter sinking is known as a countersink. It has multiple cutting edges
on its conical surface. The cutting speed for countersinking is 25% lesser than that of
drilling.
Fig.2.21 illustrates countersinking operation.
-
8/10/2019 Wood Boring Machine
40/41
-
8/10/2019 Wood Boring Machine
41/41
TrepanningTrepanning is the operation of producing a hole in sheet metal by removing metal along
the circumference of a hollow cutting tool. Trepanning operation is performed forproducing large holes. Fewer chips are removed and much of the material is saved while
the hole is produced. The tool may be operated at higher speeds. The speed depends upon
the diameter of the hole to be made. The tool resembles a hollow tube having cuttingedges at one end and a solid shank at the other to fit into the drill spindle.