Wiring Diagrams for Pickup Models - Seymour Duncan · PDF fileWiring Diagrams for Pickup...
2
Wiring Diagrams for Pickup Models: 5427 hollister avenue, Santa Barbara, CA 93111 805.964.9610 • seymourduncan.com Apollo Jazz Bass - neck Apollo Jazz Bass - bridge Apollo Jazz Bass - set Apollo Jazz Bass - neck 67mm 5 strg Apollo Jazz Bass - bridge 70mm 5 strg Apollo Jazz Bass - set 67/70 5 strg Apollo Jazz Bass - neck 70mm 5 strg Apollo Jazz Bass - bridge 74mm 5 strg Apollo Jazz Bass - set 70/74 5 strg The basic steps for installation include: 1. Remove the strings from your bass. 2. Remove the control plate and flip it over. 3. De-solder the original pickup’s wires from the controls and make sure to remember where they were connected. 4. Remove the pickup from the pickup cavity. 5. If the foam in the cavity of your bass has degraded, then replace it with the foam included with your pickups. 6. Put your SD bass pickup into the pickup cavity. 7. Tin the wires from the SD bass pickup, and then solder them into place. 8. Replace the control plate. 9. Re-string your bass, and adjust the pickup to string distance to about 1/8” for the bridge and 3/16” for the neck. Seymour Duncan Solder Solder Tip (hot output) Output Jack .047 cap Solder Neck Volume 250k Bridge Volume 250k Master Tone 250k Sleeve (ground). The inner, circular portion of the jack Solder Solder Tip (hot output) Output Jack .047 cap Solder Neck Volume 250k Bridge Volume 250k Master Tone 250k Sleeve (ground). The inner, circular portion of the jack Visit seymourduncan.com for additional wiring diagrams. Wiring for Apollo Jazz Bass 5 String Wiring for Apollo Jazz Bass 4 String P/N 501030-135 Jazz Bass and Fender are registered trademarks of FMIC, with which Seymour Duncan is not affiliated Seymour Duncan Seymour Duncan Seymour Duncan Bare + Ground White White White Bare + Ground Bare + Ground Bare + Ground White Congratulations on your purchase of a fine, hand-built, Seymour Duncan bass guitar pickup! Installing this pickup in your bass isn’t rocket science. And, if you’re already handy with tools, it’ll be a snap for you,and fun too! But if you have no experience handling red-hot soldering irons, you’d be well advised to take your new pickup and your trusty bass to a qualified guitar tech.
-
Upload
nguyenthien -
Category
Documents
-
view
226 -
download
1
Transcript of Wiring Diagrams for Pickup Models - Seymour Duncan · PDF fileWiring Diagrams for Pickup...
Wiring Diagrams forPickup Models:
5427 hollister avenue, Santa Barbara, CA 93111805.964.9610 • seymourduncan.com
Apollo Jazz Bass - neck
Apollo Jazz Bass - bridge
Apollo Jazz Bass - set
Apollo Jazz Bass - neck 67mm 5 strg
Apollo Jazz Bass - bridge 70mm 5 strg
Apollo Jazz Bass - set 67/70 5 strg
Apollo Jazz Bass - neck 70mm 5 strg
Apollo Jazz Bass - bridge 74mm 5 strg
Apollo Jazz Bass - set 70/74 5 strg
The basic steps for installation include:
1. Remove the strings from your bass.
2. Remove the control plate and flip it over.
3. De-solder the original pickup’s wires from the controls and
make sure to remember where they were connected.
4. Remove the pickup from the pickup cavity.
5. If the foam in the cavity of your bass has degraded, then
replace it with the foam included with your pickups.
6. Put your SD bass pickup into the pickup cavity.
7. Tin the wires from the SD bass pickup, and then solder them
into place.
8. Replace the control plate.
9. Re-string your bass, and adjust the pickup to string distance
to about 1/8” for the bridge and 3/16” for the neck.
Seymour Duncan
Solder
Solder
Tip (hot output)
Output Jack
.047cap
Solder
NeckVolume
250k
BridgeVolume
250k
MasterTone250kSleeve (ground).
The inner, circularportion of the jack
Solder
Solder
Tip (hot output)
Output Jack
.047cap
Solder
NeckVolume
250k
BridgeVolume
250k
MasterTone250kSleeve (ground).
The inner, circularportion of the jack
Visit seymourduncan.com for additional wiring diagrams.
Wiring for Apollo Jazz Bass 5 String
Wiring for Apollo Jazz Bass 4 String
P/N
50
103
0-1
35
Jazz Bass and Fender are registered trademarks of FMIC, with which Seymour Duncan is not affiliated
Seymour Duncan
Seymour Duncan
Seymour Duncan
Bare +Ground
White
White
White
Bare +Ground
Bare +Ground
Bare +Ground
White
Congratulat ions on your purchase of a fine, hand-bui lt , Seymour Duncan bass guitar pickup! Instal l ing this pickup in your bass isn’t rocket science. And, i f you’re already handy with tools, i t ’ l l be a snap for you,and fun too! But i f you have no experience handl ing red-hot soldering irons, you’d be wel l advised to take your new pickup and your trusty bass to a qual ified guitar tech.
Wiring Diagrams forPickup Models:
5427 hollister avenue, Santa Barbara, CA 93111805.964.9610 • seymourduncan.com
Quarter Pound P-Bass® - 5 strg
The basic steps for installation include:
1. Remove the strings from your bass.
2. Remove the control plate and flip it over.
3. De-solder the original pickup’s wires from the controls and
make sure to remember where they were connected.
4. Remove the pickup from the pickup cavity.
5. If the foam in the cavity of your bass has degraded, then
replace it with the foam included with your pickups.
6. Put your SD bass pickup into the pickup cavity.
7. Tin the wires from the SD bass pickup, and then solder them
into place.
8. Replace the control plate.
9. Re-string your bass, and adjust the pickups so they are set
about 3/16” from the strings when they are pressed down at
the highest fret on the neck.
Tip (hot output)
Output Jack
Volume250k
Ground wire from bridge
Tone250kSleeve (ground).
The inner, circularportion of the jack
Seymour DuncanSeymour Duncan
Solder
.047cap
Solder
Visit seymourduncan.com for additional wiring diagrams.P-Bass and Fender are registered trademarks of FMIC, with which Seymour Duncan is not affiliated
Wiring for 5 String Quarter-Pound for P-Bass®
White
Shield
Congratulat ions on your purchase of a fine, hand-bui lt , Seymour Duncan bass guitar pickup! Instal l ing this pickup in your bass isn’t rocket science. And, i f you’re already handy with tools, i t ’ l l be a snap for you,and fun too! But i f you have no experience handl ing red-hot soldering irons, you’d be wel l advised to take your new pickup and your trusty bass to a qual ified guitar tech.
