Wireless Control Module - Osram · Polaris 3D ®/PCS/PCW FLOOR 1 ... VIOLET Class 2, Low Voltage,...
3
— Control module for all of the following: – 0-10V dimmable luminaires – DALI ballasts – Occupancy sensors — GreenBus II ® connection available for GreenBus II devices – Area Lighting Control (ALC) Module – Phase Cut Dimming Module – Relay Panel — Connects 0-10V dimmable luminaires to network for: – Customizing lighting scenes for tailored experiences/tasks – Adjusting light levels to respond to variable lighting requirements Wireless Control Module Key Features & Benefits www.osram.us/ds System Compatibility — Works with ENCELIUM ® EXTEND Networked Light Management System — Works with ENCELIUM EDGE ™ Standalone Wireless Light Management System Light is OSRAM WCM Light Fixture Wallstation PoE Switch ENCELIUM EXTEND Ethernet Network Sensor Polaris 3D ® /PCS/PCW FLOOR 1 FLOOR 2 Light Fixture SSU WCM Sensor Router WM WM Polaris 3D ® Software Tenant Ethernet Network Daisy chain up to 3 WMs ENCELIUM ® EXTEND Networked Light Management System Architecture System Architecture This illustration shows how each component is easily integrated into the ENCELIUM EXTEND Networked Light Management System. The ENCELIUM EXTEND Wireless Manager communicates via a mesh network based on ZigBee standards. The Wireless Manager (WM) is powered using Power Over Ethernet (PoE). Each WM must be connected to an Ethernet (PoE) Network Switch using standard Cat-5 or greater Ethernet data cabling. Each WCM, sensor, and wallstation uses a wireless mesh network to relay data back to the WM. WMs typically control individual floors and are linked via an Ethernet Network back to the SSU. Internet or LAN connection allow floor plan based control software to be operated anywhere on the network. For reference, the component shown on this data sheet is highlighted. The Wireless Control Module (WCM) is a key component of the ENCELIUM EXTEND Networked Light Management System (LMS) and ENCELIUM EDGE LMS. Individually addressable, the WCM enables each ballast or LED driver to be independently controlled and configured to best meet the needs of the facility. The WCM switches a fixture ON or OFF via a relay contained in the module as well as delivers a low voltage dimming signal to any 0-10V dimming ballast/driver. OSRAM offers a special damp-rated WCM for installations subject to moderate degrees of moisture. When connected to the ENCELIUM EXTEND LMS the WCM enables a full range of low-voltage products via the GreenBus II port on the device. This enhances the flexibility of the ENCELIUM EXTEND System to include phase-cut dimming, area lighting control, low voltage wallstations, key switches, Sensor Interface Module (SIM) and relay panel control. When connected to the ENCELIUM EDGE LMS the WCM enables a limited group of low-voltage products via the GreenBus II port on the device. This enhances the flexibility of the ENCELIUM EDGE System to include phase-cut dimming and low voltage wallstations.
Transcript of Wireless Control Module - Osram · Polaris 3D ®/PCS/PCW FLOOR 1 ... VIOLET Class 2, Low Voltage,...
— Control module for all of the following: – 0-10V dimmable luminaires – DALI ballasts – Occupancy sensors
— GreenBus II® connection available for GreenBus II devices – Area Lighting Control (ALC) Module – Phase Cut Dimming Module – Relay Panel
— Connects 0-10V dimmable luminaires to network for: – Customizing lighting scenes for tailored experiences/tasks – Adjusting light levels to respond to variable lighting requirements
Wireless Control Module
Key Features & Benefits
www.osram.us/ds
System Compatibility
— Works with ENCELIUM® EXTEND Networked Light Management System
— Works with ENCELIUM EDGE™ Standalone Wireless Light Management System
Light is OSRAM
WCM
Light Fixture
Wallstation
PoE Switch
ENCE
LIUM
EXT
END
Ethe
rnet
Net
wor
k
Sensor
Polaris 3D®/PCS/PCW
FLOO
R 1
FLOO
R 2
Light Fixture
SSU
WCM
Sensor
Router
WM
WM
Polaris 3D® Software
Tenant EthernetNetwork
Daisy chain up to 3 WMs
ENCELIUM® EXTEND Networked Light Management System Architecture
System ArchitectureThis illustration shows how each component is easily integrated into the ENCELIUM EXTEND Networked Light Management System. The ENCELIUM EXTEND Wireless Manager communicates via a mesh network based on ZigBee standards. The Wireless Manager (WM) is powered using Power Over Ethernet (PoE). Each WM must be connected to an Ethernet (PoE) Network Switch using standard Cat-5 or greater Ethernet data cabling. Each WCM, sensor, and wallstation uses a wireless mesh network to relay data back to the WM. WMs typically control individual floors and are linked via an Ethernet Network back to the SSU. Internet or LAN connection allow floor plan based control software to be operated anywhere on the network. For reference, the component shown on this data sheet is highlighted.
The Wireless Control Module (WCM) is a key component of the ENCELIUM EXTEND Networked Light Management System (LMS) and ENCELIUM EDGE LMS. Individually addressable, the WCM enables each ballast or LED driver to be independently controlled and configured to best meet the needs of the facility.
The WCM switches a fixture ON or OFF via a relay contained in the module as well as delivers a low voltage dimming signal to any 0-10V dimming ballast/driver. OSRAM offers a special damp-rated WCM for installations subject to moderate degrees of moisture.
When connected to the ENCELIUM EXTEND LMS the WCM enables a full range of low-voltage products via the GreenBus II port on the device. This enhances the flexibility of the ENCELIUM EXTEND System to include phase-cut dimming, area lighting control, low voltage wallstations, key switches, Sensor Interface Module (SIM) and relay panel control.
When connected to the ENCELIUM EDGE LMS the WCM enables a limited group of low-voltage products via the GreenBus II port on the device. This enhances the flexibility of the ENCELIUM EDGE System to include phase-cut dimming and low voltage wallstations.
Ordering Information
Item Ordering Number Abbreviation System Comparability Modifiers56316 EN-WCM2-ZB-DR ENCELIUM EXTEND Damp Rated 56317 EN-WCM2-ZB ENCELIUM EXTEND56318 EN-WCM2-ZB-DR ENCELIUM EDGE Damp Rated56319 EN-WCM2-ZB ENCELIUM EDGE
1Maximum wire length: 100ft., Class 2 only
Specifications
Electrical (Absolute Maximum Ratings: all rated voltages have a tolerance of +/-10%)
— 4.5A 120-347 Vac Ballast/LED Driver
— 5.8A 120-347 Vac Tungsten
— 9.0A 120-347 Vac General Purpose
Control Options
— Single 0-10V dimming output (IEC 60929 Annex E). Capable of sinking 10mA (this is equivalent to 10 typical dimming ballasts/drivers)1
— 0-10V or DALI connectivity
— GreenBus II® connection port for GreenBus II devices
Environmental — Operating temperature range:
-40°C (-40°F) to 60°C (140°F)
Physical
— Dimensions: 3.2" x 1.7" x 1.7" (82.5mm x 42.5mm x 42.5mm)
— Standard units are for indoor use only or for mounting inside waterproof enclosure
— Damp-rated units may be used in damp locations
— Suitable for luminaire or junction box mounting in standard 1/2" knockout (7/8" dia.)
Wireless
— Radio Frequency: 2.4 GHz
— Range: 100' line of sight, 50' through stan-dard walls when mounted outside of the junction box (Range decreases by 50% when mounted inside the luminaire)
Regulatory
— Energy Management Equipment (UL 916) Emergency Lighting Equipment (UL 924 cULus Listed) Heat and Smoke Release for Air-Handling Spaces (UL 2043) FCC Part 15/ICES-003
— Complies with the following electromagnetic requirements: – EN 61000-4-2 – EN 61000-4-4 – EN 61000-4-5
— Install in accordance with all applicable national and local electrical and building codes.
Wire Color Wiring to Luminaire Wiring to Low Voltage Sensor Wiring Using GreenBus II Port Only Wire LengthBLACK Line In - Relay Contact Line In - Relay Contact Line In 9.84" (250mm)RED Line Out - Relay Contact Not Used Not Used 9.84" (250mm)WHITE Neutral Neutral (WCM Input Only) Neutral 9.84" (250mm)VIOLET Class 2, Low Voltage, 0-10Vdc, 10mA max. Power Not Used 23.62" (600mm)GREY Class 2, Low Voltage Return/Common Common Not Used 23.62" (600mm)BLUE Not Used Signal Not Used 7.09" (180mm) Note: GreenBus II port can also be used when wiring to a luminaire.
Wiring Diagrams (ENCELIUM EXTEND)
Power Feed
BLACK
ENIL
LARTUEN
RED
GREY GREY/ -VIOLET VIOLET/ + 0-10V ELECTRONIC
BALLAST/DRIVER
LARTUEN
BLUE BLUE NOT USED
Wiring to Luminaire
Power Feed
BLACK
LINE
NEUT
RAL
RED
GREY GREY/ -VIOLET VIOLET/ + NOT USED
NOT USEDBLUE BLUE NOT USED
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
41
Relays Relays
2
3
1
2
3
Power supply input24V AC, 60Hz, 1.6A (40VA)Class 2 only
Power fail input
GreenBusII . Connect to Energy Management System only.
Manual Toggle Button
TM
blue
red
WRRelays
blackbluered
GERelays
Depress with tool to unlock
1 23 45 67 89 1011 1213 1415 1617 1819 2021 2223 24
4
TMLED Always On -> 24V and GreenBusII PresentLED Single Blink -> Only GreenBusII PresentLED Double Blink -> Only 24 VAC Present
TM
Max ambient temperature +50ºC
Input: Class 2 Only24V AC, 50/60Hz, min 40VA
Relay Panel ModuleEN-RPM-24C-GB2
Install per installation instruction sheet and electrical & building codes. Connect to ENCELIUM
GreenBusII System only.
CAUTION - To Reduce the Risk of Fire or Electric Shock Do Not
Interconnect The Outputs Of Different Class 2 Circuits 85
-116-
DA
Item No 45268
Q1 Q2 Q3 Q4
Made in Canada
2012 2013 2014 2015
Emergency Lightingand Power Equipment
Energy Management Equipment Subassembly
6NA8
or or
PCDM
Relay Panel
ALC WCM
NEUTRAL
Wiring Using GreenBus II Port Only
The WCM GreenBus II connection supports any of the following devices:
ElectricalJunction Box
CeilingTile
Occupancy Sensor
GreenBus II
ElectricalJunction Box
CeilingTile
Photo Sensor
GreenBus II
Wall Station
Power Feed
BLACK
LINE
NEUT
RAL
RED
GREY GREY/ -VIOLET VIOLET/ + NOT USED
NOT USEDBLUE BLUE NOT USED
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
41
Relays Relays
2
3
1
2
3
Power supply input24V AC, 60Hz, 1.6A (40VA)Class 2 only
Power fail input
GreenBusII . Connect to Energy Management System only.
Manual Toggle Button
TM
blue
red
WRRelays
blackbluered
GERelays
Depress with tool to unlock
1 23 45 67 89 1011 1213 1415 1617 1819 2021 2223 24
4
TMLED Always On -> 24V and GreenBusII PresentLED Single Blink -> Only GreenBusII PresentLED Double Blink -> Only 24 VAC Present
TM
Max ambient temperature +50ºC
Input: Class 2 Only24V AC, 50/60Hz, min 40VA
Relay Panel ModuleEN-RPM-24C-GB2
Install per installation instruction sheet and electrical & building codes. Connect to ENCELIUM
GreenBusII System only.
CAUTION - To Reduce the Risk of Fire or Electric Shock Do Not
Interconnect The Outputs Of Different Class 2 Circuits 85
-116
-DA
Item No 45268
Q1 Q2 Q3 Q4
Made in Canada
2012 2013 2014 2015
Emergency Lightingand Power Equipment
Energy Management Equipment Subassembly
6NA8
or or
PCDM
Relay Panel
ALC WCM
NEUTRAL
Wiring Diagrams (ENCELIUM EDGE)
Power Feed
BLACK
ENIL
LARTUEN
RED
GREY GREY/ -VIOLET VIOLET/ + 0-10V ELECTRONIC
BALLAST/DRIVER
LARTUEN
BLUE BLUE NOT USED
Wiring to Luminaire
Power Feed
BLACK
LINE
NEUT
RAL
RED
GREY GREY/ -VIOLET VIOLET/ + NOT USED
NOT USEDBLUE BLUE NOT USED
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
41
Relays Relays
2
3
1
2
3
Power supply input24V AC, 60Hz, 1.6A (40VA)Class 2 only
Power fail input
GreenBusII . Connect to Energy Management System only.
Manual Toggle Button
TM
blue
red
WRRelays
blackbluered
GERelays
Depress with tool to unlock
1 23 45 67 89 1011 1213 1415 1617 1819 2021 2223 24
4
TMLED Always On -> 24V and GreenBusII PresentLED Single Blink -> Only GreenBusII PresentLED Double Blink -> Only 24 VAC Present
TM
Max ambient temperature +50ºC
Input: Class 2 Only24V AC, 50/60Hz, min 40VA
Relay Panel ModuleEN-RPM-24C-GB2
Install per installation instruction sheet and electrical & building codes. Connect to ENCELIUM GreenBusII System only.
CAUTION - To Reduce the Risk of Fire or Electric Shock Do Not Interconnect The Outputs Of Different Class 2 Circuits 85-116-D
A
Item No 45268
Q1 Q2 Q3 Q4
Made in Canada
2012 2013 2014 2015
Emergency Lightingand Power Equipment
Energy Management Equipment Subassembly
6NA8
or or
PCDM
Relay Panel
ALC WCM
NEUTRAL
OSRAM SYLVANIA Inc.
200 Ballardvale Street
Wilmington, MA 01887 USA
888-531-7573
www.osram.us/ds
OSRAM is a registered trademark of OSRAM GmbH. ENCELIUM EXTEND and GreenBus II are registered trademarks of OSRAM SYLVANIA Inc. ZigBee is a registered trademark of the ZigBee Alliance. Specifications subject to change without notice.
© 2018 OSRAM SYLVANIA Inc.
The mechanical construction allows for simple installation of the WCM to an available 1/2 inch knock-out on
the side or on top of a fixture (as shown below). All necessary wiring for the electronic dimming ballast or
LED driver is available on the inside.
For some installations, a junction box may be required. It is recommended to securely mount the WCM to
the junction box (as shown below) using an available 1/2 inch knock-out and a retainer nut.
Fixture
J Box MountingFixture Mounting
Warranty
For warranty details, refer to the full warranty documentation at www.osram.us/warranty
Dimensions and Installation Diagrams
42.5(1.7)
3.2˝(82.5mm)
1.7˝(42.5mm)
1.7˝(42.5mm)
LMS103R4 11-18
Wire Color Wiring to Luminaire Wiring Using GreenBus II Port Only Wire LengthBLACK Line In - Relay Contact Line In 9.84" (250mm)RED Line Out - Relay Contact Not Used 9.84" (250mm)WHITE Neutral Neutral 9.84" (250mm)VIOLET Class 2, Low Voltage, 0-10Vdc, 10mA max. Not Used 23.62" (600mm)GREY Class 2, Low Voltage Return/Common Not Used 23.62" (600mm)BLUE Not Used Not Used 7.09" (180mm) Note: GreenBus II port can also be used when wiring to a luminaire.
Wall Station
Power Feed
BLACK
LINE
NEUT
RAL
RED
GREY GREY/ -VIOLET VIOLET/ + NOT USED
NOT USEDBLUE BLUE NOT USED
BLUE
INP
UT
RED
OU
TPU
TBL
UEIN
PU
TRE
DO
UTP
UT
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
TBL
UEIN
PU
TRE
DO
UTP
UT
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
TBL
UEIN
PU
TRE
DO
UTP
UT
BLUE
INP
UT
RED
OU
TPU
TBL
UEIN
PU
TRE
DO
UTP
UT
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
BLUE
INP
UT
RED
OU
TPU
T
41
Relays Relays
2
3
1
2
3
Power supply input24V AC, 60Hz, 1.6A (40VA)Class 2 only
Power fail input
GreenBusII . Connect to Energy Management System only.
Manual Toggle Button
TM
blue
red
WRRelays
blackbluered
GERelays
Depress with tool to unlock
1 23 45 67 89 1011 1213 1415 1617 1819 2021 2223 24
4
TMLED Always On -> 24V and GreenBusII PresentLED Single Blink -> Only GreenBusII PresentLED Double Blink -> Only 24 VAC Present
TM
Max ambient temperature +50ºC
Input: Class 2 Only24V AC, 50/60Hz, min 40VA
Relay Panel ModuleEN-RPM-24C-GB2
Install per installation instruction sheet and electrical & building codes. Connect to ENCELIUM
GreenBusII System only.
CAUTION - To Reduce the Risk of Fire or Electric Shock Do Not
Interconnect The Outputs Of Different Class 2 Circuits 85
-116
-DA
Item No 45268
Q1 Q2 Q3 Q4
Made in Canada
2012 2013 2014 2015
Emergency Lightingand Power Equipment
Energy Management Equipment Subassembly
6NA8
or or
PCDM
Relay Panel
ALC WCM
NEUTRAL
Wiring Using GreenBus II Port Only
When connected to ENCELIUM EDGE, the WCM GreenBus II connection supports the following devices:
