Wired / Wireless

Mega-Pixel CMOS PT IP Camera

ICA-M220 / ICA-M220W

Quick Installation Guide

Table of Contents

1. Overview ................................................................................................... 3

2. Package Contents ........................................................................................ 4

3. Hardware Installation ................................................................................... 5

4. Web configuration access ............................................................................ 7

5. Cam Viewer Installation .............................................................................. 9

Further Information ...................................................................................14

�

1. Overview Thank you for purchasing the Mega-Pixel Pan/Tilt Internet Camera. It is versatile and high image solution of surveillance application. The Mega-Pixel Pan/Tilt Internet Camera is also a stand-alone camera system with a built-in processor and web server that provides highest quality video and system performance.

Before you start to use this PT Internet camera, please check the package contents. If anything is missing, please contact the dealer of purchase and return the package to claim for missing contents.

�

2. Package ContentsIP Camera

Power Adapter

Quick Installation Guide

User’s Manual CD

RJ-45 Cable

Mounting Kit

Antenna x 2 (ICA-M220W only)

�

3. Hardware InstallationBefore installation, please be sure to read this quick installation guide and user’s manual (CD) carefully to complete machine installation. This guide shows how to quick set up the two cameras.

Step 1: Connecting Network

Connect the Ethernet cable to your switch/hub, and connect the other end to the LAN jack of this IP camera.

Note

For ICA-M220W, you can skip this step if you plan to use wireless LAN only. In the first time configuration, however, we still suggest you use wired interface.

Step 2: Connecting AC Power

Plug the power adapter to wall socket, and connect the power connector to the power jack located at the bottom of the IP camera.

�

Step 3: Connecting Antennas (ICA-M220W only)

Connect the antennas to the antenna base, located at the back of the camera.

Note

Please verify your wireless connection was enable and configured.The default Wireless setting of ICA-M220W: SSID: any Network Type: InfrastructureAfter configured the wireless setting, unplug the Ethernet cable that network will switch to wireless interface automatically.

�

4. Web configuration access The ICA-M220 and ICA-M220W camera provides GUI (Web based, Graphical User Interface) for management and administration.

Step 1 Computer Network Setup

Set your computer’s IP address to 192.168.0.x, where x is an integer between 1 to 254 (except 20 where is being used for the camera by default). If you don’t know how to do this, please ask your network administrator, or refer to instructions on chapter 2.3 of user manual (in supplied CD disk)

Step 2 Login Prompt

Use web browser (Internet explorer 5.5 or above) to connect to 192.168.0.20 (type this address in the address bar of web browser) You’ll be prompted to input user name and password: admin / admin.

Step 3 Activate Installation

After logged on, you could see the following messages appear at the top of Internet Explorer

�

Click on the message, and click “Install ActiveX Control…”

When you see this message, click “Install” to install required ActiveX control

You should be able to see the images captured from the camera in the web page now. For advanced functions, please refer to instructions given in user manual

�

5. Cam Viewer Installation This chapter will guide you to install the central management software. The PT Internet Camera can be managed through its web interface. However, to central control, manage or record the cameras installed in the network Cam Viewer, the windows-based central management software are required.

Note

The Cam Viewer Pro 30 days trial version installation steps are similar. Below is the installation of Cam Viewer Lite.

1. Insert the bundled CD disk into the CD-ROM drive to launch the autorun program. Once completed, a welcome page will appear in IE. Click the “Cam Viewer Lite” hyperlink, the below InstallShield Wizard dialog box will appear.

Note

If the welcome screen does not appear, click “Start” at the taskbar. Then, select “Run” and type “X:\Cam Viewer Lite\setup.exe”, assume “X” is your CD-ROM drive.

2. Selects the language you want. Please select one of the languages and click “Next” to continue.

10

3. The welcome screen will display on the screen, please click “Next”.

4. Please read the license agreement and then check “I accept the terms of the license agreement” if you are agreed and click “Next” to continue the installa-tion

11

5. Please key in user name and company name for which you want and click “Next” to continue installation.

6. Check the option “Complete” – all program features will be installed (Requires the most disk space) and click “Next” to continue installation.

12

7. “Ready to Install the Program” will appear to prompt you to start the installation. Please click “Install” to start.

8. Please click “No” to continue.

Note

In above step, when Cam Viewer works with MBM5 (Motherboard Monitor 5), Cam Viewer will display CPU temperature and fan speed. Please click “Yes” if you need this function and refer to the Cam Viewer manual in CD disk for complete installation.

1�

9. Click “Finish” to complete the software installation.

Now, you can central manage all the PT Internet Camera installed in your network. Please refer to the Cam Viewer guide in the CD-ROM for more.

1�

Further InformationThis guide is used to help you startup your PT Internet camera settings. It is also recommended to check the user manual in CD disk for more details of the system and user configuration.

This page is intentionally left blank

This page is intentionally left blank