WIRED REMOTE CONTROLLED CAR

PROJECT

ASSEMBLED RC CAR

PROCEDURE TO

ASSEMBLE

RC CAR

Get the required components for

the project:

COMPONENTS QUANTITY

BATTERY 1

DPDT SIWTCH 2

RIBBON WIRE STRIP 3+Metre

DC GEARED MOTOR 4

CHASIS 1

DPDT SWITCH BOX 1

CAR WHEELS 4

SOLDERING SET 1

CONNECTING WIRE IF NEEDED

STEP 1

COMPONENTS OF PROJECT

Solder the ribbon wire strip with the each

motors.

Do it for all the four motors.

Place the motors in the chasis.

Tighten the motors with the required spanner.

STEP 2

MOTOR IS PLACED IN THE

CHASIS

Now, attach each wheels with the

motors.

Tighten the wheels with the motor using

the screw given with the wheels.

Place the wire as given in the diagram.

STEP 3

MOTORS TIGHTEN WITH THE

CHASIS

NOW CHECK WHETHER THE ALL

THE SOLDERED WIRES WITH THE

MOTORS ARE WORKING.

ALL THE FOUR MOTORS SHOULD

WORK PROPERLY.

IF NOT CHECK FOR THE

CONNECTIONS.

STEP 4

WIRES SOLDERED WITH THE

MOTORS

DECIDE WHICH TWO MOTORS

SHOULD GO FRONT DIRECTION.

AND DECIDE WHICH TWO MOTORS

SHOULD GO IN BACKWARD

DIRECTION.

STEP 5

NOW GIVE THE CONNECTIONS FOR THE DPDT SWITCH.

TWO DPDT SWITCHES ARE ENOUGH FOR THE WIRED RC CAR PROJECT.

IN CASE IF YOU WANT THE CAR TO BE SO GRIPPER YOU CAN USE THE FOUR DPDT SWITCHES.

HERE I USED TWO DPDT SWICHES.

STEP 6

CONNECTIONS FOR DPDT

SWITCHES

CONNECTIONS FOR THE TWO DPDT SWITCHES

ARE SHOWN IN THE DIAGRAM

GIVE THE CONNECTIONS AS PER THE

CONNECTIONS IN THE DIAGRAM.

THE CONNECTION IS THAT THE LEFT SIDE TWO

MOTORS ARE FOR ONE SWITCH.

AND THE RIGHT SIDE TWO MOTORS IN THE CAR

ARE FOR ANOTHER SWITCHES.

THIS IS HOW THE CONNECTIONS ARE THERE IN

THE DIAGRAM.

STEP 7

CONNECTIONS FOR EACH

SWITCHES

AND CONNECT THE TWO POSITIVE

ENDS OF THE DPDT SWITCHES.

AND ALSO CONNECT TWO NEGATIVE

ENDS OF THE DPDT SWITCHES.

AND GIVE THESE ENDS TO THE

BATTERY.

THE MIDDLE TWO PINS IN BOTH THE

DPDT SWITCH ARE FOR THE BATTERY

CONNECTIONS.

STEP 8

GIVE THE WIRE CONNECTIONS AS

SHOWN IN THE DIAGRAM FOR THE BOX.

PLACE THE WIRES IN THE BOX THROUGH

THE SPECIFIED HOLE.

NOW CONNECT THE WIRES WITH

BATTERY.

NOW CHECK THE WIRED REMOTE

CONTROLLED CAR IS WORKING

ACCORDING TO THE FOLLOWING

INSTRUCTIONS.

STEP 9

WIRES FROM BOX

CONNECTION OF WIRES WITH

THE BATTERY

ASSEMBLED RC CAR

WORKING OF THE DPDT

SWITCHES:

STEP 10

LEFT BUTTON RIGHT BUTTON

UP UP

DOWN DOWN

UP -----------

----------- UP

UP DOWN

DOWN UP

NIL NIL

INSTRUCTIONS OF WORKING OF DPDT

SWITCHES:

1.THE RC CAR WILL GO IN THE FRONT DIRECTION.

2.THE RC CAR WILL GO IN THE BACKWARD DIRECTION.

3.THE RC CAR WILL TURN TOWRADS RIGHT.

4.THE RC CAR WILL TURN TOWARDS LEFT.

5.THE RC CAR WILL ROTATE 360 DEGREE TOWARDS RIGHT.

6.THE RC CAR WILL ROTATE 360 DEGREE TOWARDS LEFT.

7.THE RC CAR WILL STOP RUNNING.

STEP 11

IF YOUR WIRED REMOTE

CONTROLLED CAR FOLLOWS THIS

INSTRUCTIONS THEN YOU GOT YOU

PERFECT WIRED RC CAR.

STEP 12

CHECK THE CONNECTIONS AND

THE PLACEMENT OF THE MOTORS

IN THE CHASIS AS SHOWN IN THE

DIAGRAM.

STEP 13