wind turbine _ battery recharge controller
-
Upload
mussa000 -
Category
Devices & Hardware
-
view
323 -
download
3
Transcript of wind turbine _ battery recharge controller
![Page 1: wind turbine _ battery recharge controller](https://reader034.fdocuments.us/reader034/viewer/2022042504/559c1f571a28abc7298b475e/html5/thumbnails/1.jpg)
Solar Panel Charge Controller
By Mussa Mussawi
Graded Unit 2
DG2V35
![Page 2: wind turbine _ battery recharge controller](https://reader034.fdocuments.us/reader034/viewer/2022042504/559c1f571a28abc7298b475e/html5/thumbnails/2.jpg)
ContentsØ IntroductionØ Project Purpose – Block DiagramØ Circuit Assembly:
Ø MultisimØ Bread BoardØ Strip BoardØ PCB
Ø SchematicØ Circuit Connection to the BatteryØ Skills GainedØ ConclusionØ Question time
![Page 3: wind turbine _ battery recharge controller](https://reader034.fdocuments.us/reader034/viewer/2022042504/559c1f571a28abc7298b475e/html5/thumbnails/3.jpg)
Introduction
I am building a cost effective electricity source by using the sun or wind. It will charge a 12V acid battery which will be used to operated a car park control system.I will demonstrate how I achieved this, what skills I gained in the process and what I learned about building a circuit.
![Page 4: wind turbine _ battery recharge controller](https://reader034.fdocuments.us/reader034/viewer/2022042504/559c1f571a28abc7298b475e/html5/thumbnails/4.jpg)
SOLAR PANEL 12V
CONTROLLER TO RECHARGE BATTERY
DC LOAD
DC/AC INVERTER
PLC
240 VOLTS
CAR PARK CONTROL SYSTEM
Block Diagram
![Page 5: wind turbine _ battery recharge controller](https://reader034.fdocuments.us/reader034/viewer/2022042504/559c1f571a28abc7298b475e/html5/thumbnails/5.jpg)
Circuit Assembly
I designed my circuit on the multisim, here I was able to see my mistakes and correct them without any damage or cost.Then I moved onto the bread board which allowed me to get a feel for how the circuit will actually work.Finally I assembled the final product on the PCB, allowing me to see my final product and what I had achieved.
![Page 6: wind turbine _ battery recharge controller](https://reader034.fdocuments.us/reader034/viewer/2022042504/559c1f571a28abc7298b475e/html5/thumbnails/6.jpg)
Multisim
Ø Computer programme where you build a circuit with the correct components.
Ø Shows how the components work with each other.Ø How to connect the components.Ø It will be a functional schematic.Ø Helps when choosing the source for the circuit.Ø Can see the expected out put.Ø Shows any faults in the circuit.
![Page 7: wind turbine _ battery recharge controller](https://reader034.fdocuments.us/reader034/viewer/2022042504/559c1f571a28abc7298b475e/html5/thumbnails/7.jpg)
Bread Board
Ø After testing on multisim, I assembled my circuit on the bread board.
Ø Pay attention to IC pin numbers when connecting to circuit.
Ø Input and output of transistor pin is different on the schematic.
Ø Capacitor polarities must be connected correctly.
Ø LED connection must be round the right way.
Ø
![Page 8: wind turbine _ battery recharge controller](https://reader034.fdocuments.us/reader034/viewer/2022042504/559c1f571a28abc7298b475e/html5/thumbnails/8.jpg)
PCB
Ø Red lines = copper.Ø Green lines = wire
connection.Ø Connection based
on schematic design.
![Page 9: wind turbine _ battery recharge controller](https://reader034.fdocuments.us/reader034/viewer/2022042504/559c1f571a28abc7298b475e/html5/thumbnails/9.jpg)
Schematic
Ø Deigned on the Express SCH.Ø Reference to the PCB
connections.Ø
![Page 10: wind turbine _ battery recharge controller](https://reader034.fdocuments.us/reader034/viewer/2022042504/559c1f571a28abc7298b475e/html5/thumbnails/10.jpg)
Circuit Connection to the Battery & Source
Ø 12V Solar connected to circuit through diode, fuse and relay contactor.
Ø Contactor works when batteries are full.
Ø Extra charge will work 12V bulbs. No waste of electricity.
Ø Batteries connected parallel.
Ø Negative terminal connected to earth.
Ø Output positive connected to battery positive.
![Page 11: wind turbine _ battery recharge controller](https://reader034.fdocuments.us/reader034/viewer/2022042504/559c1f571a28abc7298b475e/html5/thumbnails/11.jpg)
Skills Gained
Ø Learning about the multisim.Ø Understanding schematic diagrams.Ø PCB circuit design.Ø Soldering.Ø Component Testing.Ø Circuit Testing.Ø Logging everything in my note book.Ø Presenting the final design.
![Page 12: wind turbine _ battery recharge controller](https://reader034.fdocuments.us/reader034/viewer/2022042504/559c1f571a28abc7298b475e/html5/thumbnails/12.jpg)
Conclusion
This project was very enjoyable as it allowed me to learn new skills. It taught me how to use programmes that I will be using throughout my Engineering Career.It allowed me to keep track of what I was doing in order to achieve a final product.
![Page 13: wind turbine _ battery recharge controller](https://reader034.fdocuments.us/reader034/viewer/2022042504/559c1f571a28abc7298b475e/html5/thumbnails/13.jpg)
Question time?