WINCHESTER SUPER X PUMP, PUMP-ACTION SHOTGUN OWNER’S MANUAL

7/29/2019 WINCHESTER SUPER X PUMP, PUMP-ACTION SHOTGUN OWNERS MANUAL

1/36

Winchester Super X Pump, Pump-Action Shotgun Owners Manual


2/36

Important instructions for the

Winchester Super X PumpPump-Action ShotgunWinchester Repeating ArmsCustomer Service Department (United States)275 Winchester AvenueMorgan, Utah 84050-9333Phone: (800) 945-5237

If you have any questions or comments regarding your newfirearm, please feel free to write or call us. Use the spacebelow to record information about your new firearm.

Model ________________________________________

Serial Number _________________________________

Purchased From ________________________________

Date of Purchase _______________________________

Winchester is a registered trademark of Olin Corporation.

NEU09061/09102

C P

You are Responsible for Firearms Safety . . . . . . . . . . . . . .1

General Description and Operation . . . . . . . . . . . . . . . . .6

Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Initial Cleaning and Oiling . . . . . . . . . . . . . . . . . . . . . . . . 7

Operation of the Safety . . . . . . . . . . . . . . . . . . . . . . . . 10

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Ammunition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Magazine Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Three-Shot Adapter (Plug) . . . . . . . . . . . . . . . . . . . . . . . 14Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Firing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Unloading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Interchangeable Choke Tube System . . . . . . . . . . . . . . .20

Scope Mounting Instructions . . . . . . . . . . . . . . . . . . . . .22

E x t r a B a r r e l s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4

Cleaning and Maintenance Suggestions . . . . . . . . . . . . .24Parts, Service, Repair and Questions. . . . . . . . . . . . . . . .31

Website Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .32


3/36

YouAre responsible For

FireArms sAFetY

FailuretoFollowanyoFtheFollowing

warningsCouldresultinseriousinjuryordeath.

As a firearm owner, you accept a set of demandingresponsibilities. How seriously you take theseresponsibilities can be the difference between lifeand death.

There is no excuse for careless or abusive handling ofany firearm. At all times handle this firearm and allother firearms with intense respect for their power andpotential danger.

Please read and understand all of the cautions, warnings,notices, proper handling procedures and instructionsoutlined in this owners manual before using yournew firearm.

1 alwaysKeePtheMuZZleoFyourFirearM

PointedinasaFedireCtioneventhoughyou

areCertainitisunloaded.

Never point any firearm at anything you do not intendto shoot. Be extremely alert and aware ofall persons and property within the range ofyour ammunition.

2 neverrelytotallyonyourFirearMs

MeChaniCalsaFetydeviCe.liKeany

MeChaniCaldeviCe,asaFetyCansoMetiMes

Fail;itCanbejarredorinadvertently

ManiPulatedintoanunsaFeCondition.

The word safety describes a firearms trigger blockmechanism, sear block mechanism, hammer blockmechanism or firing pin block mechanism.Mechanical safeties are designed to place yourfirearm in a safer status, and no guarantee can be madethat the firearm will not fire even if the safety is inthe on safe position. Mechanical safeties merely aidsafe gun handling and are no excuse for pointing yourfirearms muzzle in an unsafe direction. See Operation

of the Safety on page 10 for instructions on theoperation of this firearms safety.

Remember, safe gun handling does not stop with yourfirearms mechanical safety devices, it starts there.Always treat this firearm with the respect due aloaded, ready-to-fire firearm.

Some firearms do not have a mechanical safety.Many target firearms, lever-action firearms and pistolsdo not have manual safety mechanisms. Therefore it

is critical to read and understand the owners manualfor every firearm which explains the safe operation ofthe firearm.

1


4/36

2

While it is a good idea to test your firearmsmechanical safety periodically for proper function,never test the safety while your firearm is loaded orpointed in an unsafe direction.

3 wheneveryouhandleanyFirearM,orhandit

tosoMeone,alwaysoPentheaCtioniMMediatelyandvisuallyCheCKtheFirearMs

ChaMbertoMaKeCertainthattheFirearMis

CoMPletelyunloaded.

Make certain the firearm does not inadvertentlycontain any ammunition. Remember, merelyremoving the magazine does not mean the chamberis unloaded. Always keep the chamber empty andthe safety in the on safe position unless shootingis imminent.

4 alwayswearearandeyeProteCtion

whenshooting.Unprotected, repeated exposure to gunfire can causehearing damage. Wear hearing protection (shootingear plugs or muffs) to guard against such damage.

Wear shooting glasses to protect your eyes from flyingparticles. Allow proper distance (eye relief) between

a scope and your eye when firing a scoped pistol,rifle or shotgun. Do not use unorthodox shootingmethods that could cause the rearward travel of theslide or bolt of a firearm to contact your eyes, face orhands. Always keep a safe distance between themuzzle of your firearm and any persons nearby, as

muzzle blast, debris and ejecting shells could inflictserious injury.

Always wear eye protection when disassembling andcleaning any firearm to prevent the possibility ofsprings, spring-tensioned parts, solvents or other

agents from contacting your eyes.

5 KeePallFirearMsunloadedduring

transPort,evenwhenstoredinaholster,

gunCase,sCabbardorotherContainer.

6 droPPingorjarringaloadedFirearMCan

CauseaCCidentaldisCharge.This can occur even with the safety in the on safeposition. Be extremely careful while hunting or during

any shooting activity to avoid dropping any firearm.7 huntingFroMelevatedsurFaCessuChas

treestandsisdangerous.Doing so may increase the risk of mishandling afirearm. The following rules should always be observedby you and those you hunt with. Always make certainthat the stand being used is safe and stable. Alwaysmake certain that your firearm is unloaded when it isbeing taken up and down from the stand. Always

make certain that your firearm is not dropped from thestand, or dropped while it is being taken up or downfrom the stand. Remember, a loaded firearm maydischarge when dropped, even with the safety in the

on safe position.


5/36

8 storeyourFirearMandaMMunition

seParately,wellbeyondthereaCh

oFChildren.Take prudent safeguards to ensure your firearm doesnot become available to untrained, inexperienced or

unwelcome hands. Store all firearms in secure, lockedcases or a gun safe. Keep your firearm unloaded whennot in use.

9 bewareoFbarrelobstruCtions.Mud, snow and an infinite variety of other objects mayinadvertently lodge in a barrel bore. It only takes asmall obstruction to cause dangerously increasedpressures that can damage your firearm and causeserious injury to yourself and others.

beForeCheCKingForabarrelobstruCtion,beCertainyourFirearMisCoMPletely

unloaded,thereisnotaliveshellin

theChaMberandthesaFetyisinthe

onsaFePosition.

After assuring yourself that the firearm is completelyunloaded, open the breech or action and look throughthe barrel to be sure it is clear of obstructions. If an

obstruction is seen, no matter how small it may be,clean the bore with a cleaning rod and patch asdescribed on page 23 of this owners manual.

10 bealerttothesignsoFaMMunition

MalFunCtion.iFyoudeteCtanoFFsoundor

lightreCoilwhenashellisFired,donot

loadanothershellintotheChaMber.If your firearm fails to fire, keep the muzzle pointed in

a safe direction for a minimum of 30 seconds.Carefully open the action and remove the shell fromthe chamber. If the primer is indented, the defectiveshell should be disposed of in a way that cannot causeharm. If the primer is not indented, your firearmshould be examined by a qualified gunsmith and thecause of the malfunction corrected before further use.Glance down the barrel to make sure that noobstructions remain in the barrel. Completely clearthe barrel before loading and firing again. Failure to

follow these instructions can cause extensive damageto your firearm and possible serious injury to yourselfand others.

11 neverinsertashelloFtheinCorreCtgauge

intoanyFirearM.The gauge of your firearm is marked on the barrel.Store all shells of different gauges in completelyseparate and well-marked containers. Never storeshells of mixed gauges in a common container or inyour pockets. See page 13 for more information on thecorrect ammunition for your firearm.

3


6/36

12 exaMineeveryshellyouPutin

yourFirearM.We assume no responsibility for the use of unsafe orimproper firearm and ammunition combinations ordamage or injury caused by damaged ammunition.

It is your responsibility to read and heed all warningsin this owners manual and on ammunition boxes.See page 13 for more information on the correctammunition for your firearm.

13 useonlysaaMiaPProvedaMMunition.The barrel and action of this firearm have beenmade with substantial safety margins beyond thepressures developed by established Americancommercial loads. Nevertheless, we can assume no

liability for incidents which occur through the useof shells of nonstandard dimensions or which developpressures in excess of commercially availableammunition which has been loaded in accordancewith standards established by the Sporting Arms andAmmunition Manufacturers Institute (SAAMI).

14 MaKesureoFadequateventilationinthe

areathatyoudisChargeaFirearM.lead

exPosureCanoCCurFroMdisCharging

FirearMsinPoorlyventilatedareas,CleaningFirearMsorhandlingaMMunition.Lead is a substance that has been known to cause birthdefects, reproductive harm and other serious injury.Wash hands thoroughly after exposure to ammunitionor after cleaning a firearm.

15 donotsnaPtheFiringPinonaneMPty

ChaMber;theChaMberMaynotbeeMPty!Treat every firearm with the respect due a loadedfirearm, even though you are certain the firearmis unloaded.

16 KeePyourFingersawayFroMthetriggerwhileloadingandunloadinguntilshooting

isiMMinent.

17 besureoFyourtargetandbaCKstoP,

PartiCularlyduringlowlightPeriods.Know the range of your ammunition. Never shoot atwater or hard objects.

18 alwaysunloadyourFirearMsChaMber

beForeCrossingaFenCe,CliMbingatree,juMPingaditChornegotiating

otherobstaCles.Never place your firearm on or against a fence, tree,car or other similar object.

19 bedeFensiveandonguardagainstunsaFe

gunhandlingaroundyouandothers.Dont be timid when it comes to firearm safety.If you observe other shooters violating any ofthese safety precautions, politely suggest saferhandling practices.

4


7/36

5

20 beCertainyourFirearMisunloaded

beForeCleaning.Because so many firearm accidents occur when afirearm is being cleaned, special and extreme careshould be taken to be sure your firearm is unloaded

before disassembly, cleaning and reassembly.Keep ammunition away from the cleaning location.

Never test the mechanical function of any firearm with

live ammunition.

21 teaChandsuPerviseFirearMssaFetyto

allMeMbersoFyourFaMily,esPeCially

toChildrenandnon-shooters.Closely supervise newcomers to the shooting sports.Encourage enrollment in hunting and shootingsafety courses.

22 neverdrinKalCoholiCbeveragesortaKeany

tyPeoFdrugsbeForeorduringshooting.Your vision, motor skills and judgment could bedangerously impaired, making your gun handlingunsafe to you and to others.

23 readandheedallwarningsinthisowners

Manual,onaMMunitionboxesandwithall

aCCessoriesthatyouinstallonyourFirearM.It is your responsibility to secure the most up-to-dateinformation on the safe handling procedures of yourWinchester firearm. We assume no liability forincidents which occur when unsafe or improper firearmaccessories or ammunition combinations are used.

24 PraCtiCePeriodiCMaintenanCe,avoid

unauthoriZedserviCing.Your firearm is a mechanical device which will not lastforever, and as such, is subject to wear and requiresperiodic inspection, adjustment and service.

Winchester firearms should be serviced by aWinchester Repeating Arms Authorized RepairCenter or by our Service Facility in Arnold, Missouri.We assume no responsibility for injuries suffered orcaused by unauthorized servicing, alterations ormodifications of Winchester firearms.

25 wereservetherighttoreFuseserviCeon

FirearMsthathavebeenaltered,addedto

orsubstantiallyChanged.

Removal of metal from the barrel, or modificationsof the firing mechanism and/or operating parts, maylead to a refusal of service on such firearms. We willcharge you for parts and labor to return the firearm tooriginal specifications.

donot,underanyCirCuMstanCes,alter

thetrigger,saFetyorotherPartsoF

theFiringMeChanisMoFthisoranyother

FirearM.FailuretoobeythiswarningMay

resultininjuryordeathtoyourselF

orothers.

b e C a r e F u l !


8/36

6

GenerAl DescriptionAnD operAtion

GenerAl Description

No pump shotgun is faster than the Winchester Super XPump. Inertia from recoil forces assists the slide rearward,making it much easier to begin the pumping motion.Youll find that you will complete the pumping actionforward quickly and in an instant youve cycled a shell andare ready for a second shot. Speed like this makes a bigdifference, allowing you to set up for a follow-up shot

more quickly and concentrate on your target, not just onpumping the shotgun.

With the Super X Pumps rotary bolt design, the lugsengage directly in the recesses in the barrel extension.

This is a strong, consistent and reliable lockup design.Every design feature of the Super X Pump works togetherto make what many consider the most reliable pumpshotgun on the market today.

GenerAl operAtion

The Super X Pump is a pump-action shotgun that allowsyou to load a shell by cycling the action to eject the emptyshell, and move an unfired shell from the loaded magazinetube to the chamber. This can be repeated until the

magazine is empty. A single shell can also be inserted intothe chamber manually.

The Super X Pump breaks down into two pieces (receiver/stock assembly and barrel) for cleaning and storage.

FIGURE 1

Receiver

Safety

Bolt Ejection Port

Magazine

Disconnector

Release Button

(Left Side)

TriggerForearm

MuzzleBarrel

Loading Port

Front Sight

Recoil Pad

Trigger Guard

Buttstock

Ventilated Rib

Magazine CapBarrel Bracket


9/36

7

Prior to using live ammunition, familiarize yourselfthoroughly with the operating instructions in thisowners manual. Get accustomed to the feel of your newfirearm and know the forces required to operate theaction. Learn how to pull the trigger and, above all, knowthe location and operation of the safety. Procedures fordisassembly and operation of various components areoutlined later in this owners manual. Please read andstudy them thoroughly.

nomenclAture

In conventional firearm terminology the position andmovement of firearm parts are described as they occurwith the firearm horizontal and in the normal firing

position: i.e., the muzzle is forward or in front; thebuttstock is rearward or to the rear; the trigger isdownward or underneath; the rib is upward or on top.For general parts nomenclature, refer to Figure 1, page 6.

The Super X Pump is also shown disassembled to theextent necessary in order to follow the instructionscontained in this owners manual (Figure 11, page 26).Figure 2, on pages 8 and 9, covers the general features andbenefits of the Super X Pump design.

Throughout this owners manual the action refers to themechanism of this shotgun which loads and secures theshells in the chamber.

seriAl number

The serial number is located on the left side of thereceiver, just above the trigger guard. Record the serialnumber at the front of this book for future reference.

initiAl cleAninGAnD oilinG

NOTICE!PleasetaKenoteoFtheFollowing

inForMationbeForeCleaningyourFirearM.

cleAninG pArts With speciAl Finishes

Be especially careful when cleaning firearms withcamouflage, Dura-Touch Armor Coating and otherspecial finishes. Always prevent these surfaces from

coming in contact with cleaning solvents, barrelscrubbers and other strong chemicals. It is preferable toclean these surfaces with a light gun oil containing nosolvents or with a damp cloth and mild dish soap (be sureto keep water out of the action). When cleaning yourfirearms bore and action, protect the external finishesfrom any contact with chemicals used. Also, avoid anycontact between external finishes and other strongchemicals like those found in DEET-containing insectrepellents, sunscreens, etc. Damage to camouflage,

Dura-Touch and other finishes caused by chemicals isirreversible and not repairable.

(Continued on page 10.)


10/36

FIGURE 2

8

Stocks are profiled for an ideal fit.

Convenient push button safety.

The Inflex Technology recoil pad utilizes

directional deflection and a soft durometer

for maximum comfort.

The advanced, high-strength alloy receiver

is much lighter than steel.

The rugged rotary bolt design engages

the barrel extension instead of the top

of the receiver.

shotGunFeAtures


11/36

9

Faster pump-action. Inertia assists you as you pump the

forearm rearward to load for the next shot.

Most Super X Pump hunting models are fitted with the Invector-

Plus interchangeable choke system. It allows you to change choke

constriction to the demands of the game being hunted or your shooting

situation. You can easily change the pattern size and density by simply

switching choke tubes. A variety of accessory choke tubes are available.


12/36

weareyeProteCtionwhenasseMblingand

disasseMblingyourshotguntoPreventsPrings,

sPring-loadedParts,solventsorotheragents

FroMContaCtingyoureyes,resultingininjury.

Some metal parts of your new Super X Pump have beencoated at the factory with a rust preventative compound.Before using your Super X Pump, clean the anti-rustcompound from the inside of the barrel, receiver, boltmechanism and the action/chamber areas. A high quality,lightweight gun oil should be used to remove thiscompound and to give your new firearm its firstlubrication. Clean the barrel using a cleaning rod andpatch as explained under Cleaning and Maintenance

Suggestions found on page 23 in this owners manual.

Before beginning assembly of your Super X Pump youshould first wipe the mechanism clean and apply a fewdrops of quality oil on the indicated surfaces (Figure 3).

Avoid applying too much oil. Only a light film is necessary.Excessive oil should be wiped off, especially in coldweather.

operAtionoFthe sAFetY

alwaysKeePthesaFetyintheonsaFePosition

unlessshootingisiMMinent.alwaysKeePthe

MuZZlePointedinasaFedireCtion.Failureto

FollowthesewarningsCouldresultinserious

injuryordeath.

The cross bolt safety is designed to prevent the triggerfrom being pulled when in the on safe position. Thesafety is located at the front of the trigger guard(Figure 4, page 11). In the off safe position, a red warningband is visible on the safety button on the left side of thetrigger guard. It is essential that you become very familiarwith the feel, look and operation of the safety on thisshotgun before attempting to load and shoot.

To place the firearm on safe, press the safety button tothe right (Figure 4, page 11). To move the safety to theoff safe or fire position, press the safety button to the left.

10

FIGURE 3

Oil lightly at these points.

Firing Pin

Magazine Tube

Ejector

Lugs

Bolt


13/36

This exposes the red warning band on the safety button(Figure 5).

With the safety in the on safe position the trigger andhammer are blocked and the shotgun cannot be fired. Inthe off safe position if your firearm is loaded with a shell inthe chamber the chambered shell can be fired by simplypulling the trigger.

donotdePendontheredColoraloneto

indiCateyourFirearMssaFetystatus.tiMe,

exPosuretotheeleMents,andtheabrasive

aCtionoFCleaningagentsCaneraseit.Failure

toFollowthiswarningCouldresultinserious

injuryordeath.

AssemblY

alwaysKeePtheMuZZlePointedinasaFe

direCtion.beForestartingasseMbly

ProCedures,visuallyinsPeCttheChaMbertobe

absolutelyCertaintheFirearMisCoMPletely

unloaded.PlaCethesaFetyintheonsaFe

Position.FailuretoFollowthiswarningCould

resultinseriousinjuryordeath.

11

FIGURE 4

The safety shown in the

on safe position.

FIGURE 5

The safety shown in the

off safe position.


14/36

12

weareyeProteCtionwhendisasseMblingand

asseMblingyourshotguntoPreventsPrings,



The Super X Pump shotgun is delivered in the box withthe barrel removed and the forearm attached to themagazine tube.

1. Remove the barrel and receiver/stock section from thebox and clean and oil them as explained on page 10.

2. Unscrew the magazine cap from the magazine tube.

3. Your shotgun will usually come out of the box with thebolt assembly in the closed position (forward), withthe trigger assembly already in place in the receiver.The barrel can be installed with the action closed, butit is easier if the action has been opened slightly.

4. Unlock and open the action by pushing up on thedisconnector release button at the rear of the triggerguard (Figure 6, page 13) on the left side and pull backon the forearm.

5. Grasp the barrel ahead of the barrel bracket.

6. Position the barrel over and in line with themagazine tube.

7. Slide the barrel rearward.

8. Guide the barrel bracket over the magazine tube andguide the barrel extension into the receiver. Be sure

that the slot in the barrel aligns with the ejector. As aguide in assembly, align the rib on the barrel assemblywith the grooves on the top of the receiver.

9. Slide the barrel rearward until it seats in the receiver.

10. Immediately replace the magazine cap. Tighten

it hand-tight (at least three full turns) to ensuresecure engagement.

DisAssemblY


direCtion.beForestartingdisasseMbly

ProCedures,oPentheaCtionandvisually

insPeCttheChaMbertobeabsolutelyCertain

theFirearMisCoMPletelyunloaded.PlaCethe

saFetyintheonsaFePosition.Failureto

FollowthiswarningCouldresultinserious

injuryordeath.

1. Depress the disconnector release button, found behindthe trigger guard on the left side (Figure 6, page 13) tounlock the action without releasing the hammer.

2. Open the action and place the safety in the on safeposition. (The red warning band must not be visible.)

3. With the magazine pointed in a safe direction,unscrew and remove the magazine cap. Be careful, themagazine spring and magazine plug are retained by afriction-type retainer.


15/36


CleaningyourshotguntoPreventsPrings,



4. With one hand, grasp the barrel ahead of the barrelbracket, hold the buttstock with your other hand.

5. Pull the barrel forward to disengage it from thereceiver. Slide the barrel bracket off the magazine.Do not use excessive force.

6. Immediately replace the magazine cap and handtighten at least three turns.

Ammunition

useonlyshellsoFtheCorreCtgaugeand

length.thegaugeandlengthoFtheChaMberis

insCribedonthesideoFthebarrel.donotuseaMMunitionotherthanwhatisinsCribedonthe

sideoFthebarrel.exaMineeveryshellyouPut

inyourshotgun.FailuretoFollowthiswarning

Couldresultinseriousinjuryordeathand

CausedaMagetoyourshotgun.

useshellsoFtheCorreCtlength.donotuse3"

or3"shellsinabarrelwitha2"or2"

ChaMber,or3"shellsinabarrelwitha3"ChaMber.doingsoCanresultinabuilduPoF

dangerouslyhighPressures.FailuretoFollow

thiswarningCouldresultinseriousinjuryor

deathandCausedaMagetoyourshotgun.

donotPuta20gaugeshellina12gauge

shotgun.donotPuta28gaugeshellina20

gaugeshotgun.donotPuta.410boreshellina

28gaugeshotgun.neverPutMetalliCCartridges

oFanyKindinashotgun.sPeCiFiCally,neverPut

CenterFireriFleorPistolshellsinashotgun

ChaMberedFor.410bore.FailuretoFollowthese

warningsCouldresultinseriousinjuryor

deathandCausedaMagetoyourshotgun.

13

FIGURE 6

Press the disconnector release button

to unlock the action.


16/36

The most certain way to bulge or rupture a shotgun barrelis to load a smaller gauge shell into a larger gauge chamber.The smaller gauge shell will not fall completely throughthe barrel; its rim is caught by the front of a larger gaugechamber or at the larger gauges choke. Your shotgun willmisfire (with the chamber appearing to be empty). It isthen possible to load the correct gauge shell behind thesmaller gauge shell. If the shotgun is then fired, the resultwill be a so-called 12-20, 20-28 or 28-.410 burst whichcan cause extensive damage to your shotgun and possibleserious injury to you and others.

We can assume no responsibility for incidents which occurthrough the use of shells of nonstandard dimension orthose developing pressures in excess of SAAMI (SportingArms and Ammunition Manufacturers Institute)established standards.

All current 12 and 20 gauge Super X Pumps have a 3"chamber and are designed to shoot all factory 2" and 3"Field and Target loads. The barrel can safely handle bothlead and steel shot. Special rifled choke tubes are designedfor shooting sabot-type slugs.

mAGAzine cApAcitY

With the magazine three-shot adapter (plug) removed,your shotgun holds four 2" or 3" shells in the magazine.SXP models with an extended magazine hold six 2" or 3"shells in the magazine. At a range or other suitableshooting location, load the magazine to full capacity toverify the number of shells.

Remember, total capacity includes an additional shell inthe chamber in addition to a full magazine.

three-shot ADApter (pluG)


direCtion.beForereMovingorinstallingthe

three-shotadaPter,CoMPletelyunloadthe

shotgun.oPentheaCtionandvisuallyinsPeCt

theChaMber,FeedMeChanisMandMagaZinetobe

absolutelyCertaintheFirearMisCoMPletely

unloaded.PlaCethesaFetyintheonsaFe

Position.FailuretoFollowthiswarningCould

resultinseriousinjuryordeath.

weareyeProteCtionwhenreMovingor

installingthethree-shotadaPtertoPrevent

sPrings,sPring-loadedParts,solventsor

otheragentsFroMContaCtingyoureyes,

resultingininjury.

The Super X Pump shotgun is delivered with the magazinethree-shot adapter (plug) installed in the magazine,limiting magazine capacity to two shells in compliancewith federal migratory bird regulations. If you do not wishto be limited to three shots when it is not required by law,you can remove the three-shot adapter.

14


17/36

removinG the three-shot ADApter (pluG)

1. Unscrew the magazine cap and remove it.

2. The magazine three-shot adapter is locatedunderneath the magazine spring retainer and isunder pressure from the magazine spring. Using yourindex finger or a large blade-type screwdriver, pressthe magazine spring retainer into the magazineapproximately 1" and rotate it turn (Figure 7).

3. The magazine spring retainer is under pressurefrom the magazine spring. Keep the magazine springunder control and carefully remove the magazinespring retainer (Figure 8). Remove the magazine

three-shot adapter (plug) and replace the magazinespring retainer.

4. Align the full-length grooves in the magazine springretainer with the protrusions inside the magazinetube, found at the six and nine o'clock positions.

5. Compress the magazine spring back into themagazine tube.

6. Replace the magazine spring retainer by pushing itinto the magazine tube approximately 1" and rotatingit turn to lock it in place. Make sure the magazinespring retainer is locked into place.

7. Install the magazine cap.

15

FIGURE 8

Maintain control of the

magazine spring as you

remove the magazine

spring retainer.

FIGURE 7

Push down on the

magazine spring retainer

and rotate it turn.


18/36

instAllinGthe three-shot ADAptor (pluG)

If you need to install the magazine three-shot adapter(plug) to limit your shotgun magazine to two shellsagain perform the following operation:

1. Unscrew the magazine cap and remove it.

2. Using your index finger or a large blade-typescrewdriver, press the magazine spring retainerinto the magazine approximately 1" and rotate it turn (Figure 7).

3. The magazine spring retainer is under pressurefrom the magazine spring, keep the magazine springunder control and carefully remove the retainer.Place the magazine three-shot adapter (plug) on

top of the magazine spring and replace the magazinespring retainer.

4. Align the full-length grooves in the magazine springretainer with the protrusions inside the magazine tube,found at the six and nine o'clock positions.

5. Compress the magazine spring and magazinethree-shot adapter back into the magazine tube.

6. Replace the magazine spring retainer by pushingit into the magazine tube approximately 1" androtating it turn to lock it in place. Make surethe magazine spring retainer.

7. Install the magazine cap.

loADinG

whenloadingyourshotgunalwaysKeePthe

MuZZlePointedinasaFedireCtion,alwaysPlaCe

thesaFetyintheonsaFePositionandKeeP

yourFingersawayFroMthetrigger.Failureto


injuryordeath.

16

FIGURE 9

Position the shell fully forward in the magazine.


19/36

donotCarryyourshotgunwithashellinthe

ChaMbertoavoidaCCidentaldisCharge.when

FiringisnolongeriMMinent,MaKesurethe

saFetyisintheonsaFePositionandunload

theChaMber.FailuretoFollowthesewarnings

Couldresultinseriousinjuryordeath.

loADinGthe mAGAzine

1. Place the safety in the on safe position and closethe action.

2. Depress the shell carrier in the loading port with thefront of the shell (Figure 9).

3. With your thumb on the base of the shell, push the

shell into the magazine until it is retained by theshell stop.

4. Repeat the procedure until the magazine isfully loaded.

loADinGthe chAmberFrom the mAGAzine

1. With the bolt closed, depress the carrier with the frontof the shell and, using your thumb, push the shell intothe magazine until the shell is held in place by the

shell stop.2. If desired, continue to load the magazine, as explained

above, to full capacity.

3. If firing is imminent, a shell can now be moved fromthe magazine to the chamber by depressing thedisconnector release button found behind the triggerguard on the left side and cycling the forearm. A shellwill be fed automatically from the magazine to thechamber as the bolt closes. Another shell can then beinserted into the magazine to load to full capacity.

theshotgunisnowreadytoFirebysiMPly

MovingthesaFetytotheoFFsaFePosition

andPullingthetrigger.

loADinGthe chAmber throuGhthe

ejection port

1. Depress the disconnector release button found behindthe trigger guard on the left side. This unlocks theaction without releasing the hammer. Slide theforearm completely rearward. Visually inspect thechamber, feed mechanism and magazine to make surethey are clear of any obstructions.

2. Insert a shell of the proper gauge and length throughthe ejection port into the open breech.

3. Slide the forearm completely forward.4. If desired, load the magazine as previously explained

to full capacity.

17


20/36

theshotgunisnowreadytoFirebysiMPly

MovingthesaFetytotheoFFsaFePosition

andPullingthetrigger.

FirinG

neverloadashellintotheChaMberorPlaCe

thesaFetyintheoFFsaFePositionunless

shootingisiMMinent.alwaysKeePtheMuZZle

PointedinasaFedireCtion.FailuretoFollow

thesewarningsCouldresultinseriousinjury

ordeath.

1. Place the safety in the on safe position.

2 Load a shell into the chamber as explainedpreviously.

3. With a shell in the chamber, you need only move thesafety to the off safe position to fire the shotgun.

4. When ready to fire, move the safety into the off safeposition, take aim and squeeze the trigger.

5. If you wish to continue firing, pull the forearmcompletely rearward until the fired shell is ejected outof the ejection port.

6. Push the forearm completely forward, transferringa new shell from the magazine into the chamber.

Your Super X Pump is again ready to fire. Immediatelyput the safety in the on safe position (with thered warning band hidden) until you are ready tofire again.

aFterFiring,orwhenshootingisnolonger

iMMinent,iMMediatelyPlaCethesaFety

intheonsaFePosition.FailuretoFollow


ordeath.

evenwiththeboltloCKedoPenaFtershooting,

donotassuMetheshotgunisunloaded.

alwaysinsPeCttheChaMber,barrel,Feed

MeChanisMandMagaZinetobeCertainthe

shotgunisCoMPletelyunloaded.Failureto


injuryordeath.

unloADinG

whenunloadingyourshotgunalwaysPlaCethe

saFetyintheonsaFePosition.KeePthe

MuZZlePointedinasaFedireCtionandyour

FingersawayFroMthetrigger.Failureto


injuryordeath.

18


21/36

alwaysinsPeCttheChaMber,barrel,Feed

MeChanisMandMagaZineCareFullyaFter

unloadingtobesureallliveshellsare

ClearedFroMtheFirearM.

unloADinG

bY

cYclinG

the

Action

Perform the following steps to remove shells from thechamber and magazine on all Super X Pump models.

1. Place the safety in the on safe position.

2. Press the disconnector release button to release theslide (Figure 6, page 13).

3. Slide the forearm through a complete cycle of theaction and repeat the process until all the shells in the

magazine have been transferred to the chamber andthen ejected.

4. When the last shell in the magazine has been cycledthrough the chamber and out the ejection port, leavethe action open.

5. Using your index finger, feel the entry of themagazine to make sure there are no longer anyshells in the magazine.

unloADinGFrom the mAGAzine

The shells can also be removed from the magazine byfollowing these steps:

1. Place the safety in the on safe position, make surethe action is closed and keep the muzzle pointing ina safe direction.

2. Turn the firearm over so the trigger guard is facing up,then push the carrier down as far as it will go.

3. Push inward on the shell stop to release a shellfrom the magazine (Figure 10). Press the shell stopagain to release the second shell. The shell stop islocated on the inside-right of the ejection port.When a shell is in the magazine the shell stop restson the brass of the shell.

19

FIGURE 10

Press the shell stop inward to

release shell from magazine.


22/36

4. With the safety still in the on safe position, returnthe firearm to the normal firing position. Pressthe disconnector release button and move theforearm all the way rearward to remove the shellfrom the chamber.

interchAnGeAble choke tube sYstem

neveratteMPttoreMove,installortightena

ChoKetubeinaloadedFirearM.whenever

reMoving,installingortighteningaChoKetube

inashotgun,alwaysKeePtheMuZZlePointedin

asaFedireCtion.CoMPletelyunloadthe

shotgun.oPentheaCtionandvisuallyinsPeCttheChaMber,FeedMeChanisMandMagaZineto

beabsolutelyCertaintheFirearMis

CoMPletelyunloaded.

alwaysPlaCethesaFetyintheonsaFe

PositionandKeePyourFingersawayFroMthe

trigger.FailuretoFollowthesewarnings

Couldresultinseriousinjuryordeath.

donotFirethisshotgunwithouttheCorreCtChoKetubeinstalled.PerManentdaMageMay

resulttothethreadsinsidethebarrel.

useonlytheaPProPriategaugeandtyPeoF

ChoKetubes,MarKedinveCtor-Plusorstandard

inveCtor,dePendingonyourshotgun.

inveCtor-PlusChoKetubesareForuseonlyin

winChestershotgunswithbaCK-boredbarrels,

andarenotinterChangeablewithwinChoKeor

standardinveCtorChoKetubes.donotuse

inveCtor-PlustubesinbarrelsthreadedFor

standardinveCtortubes.

standardinveCtortubesareForuseonlyin

winChestershotguns,andarenot

interChangeablewithinveCtor-PlusChoKe

tubes.donotusestandardinveCtortubesin

barrelsthreadedForinveCtor-Plustubes.

donotusewinChoKe,standardinveCtoror

inveCtorPlusChoKetubesinanyshotgun

barrelsnotsuPPliedbywinChester.do

notuseanyotherChoKingdeviCeinany

shotgunbarrelssuPPliedbywinChester

rePeatingarMs.

FailuretoFollowthesewarningsMay

CauseinjuryordeathandCausedaMagetoyourshotgun.

20


23/36

All Super X Pump shotgun barrels (except Defendermodels) are threaded to accept the Invector-Plus choketube system. WinChoke, Standard Invector andInvector-Plus tubes are not interchangeable. Confirm thechoke system of your shotgun by looking on the right sideof the barrel where the specifications are inscribed, wherethe choke markings are normally located.

The constriction of each choke tube is indicated twice onthe choke tube: on the side of the tube, and indicatedwith a notch code on the top rim of the tube. Theincluded universal choke tube wrench is used to removeand install choke tubes.

Invector-Plus and Standard Invector choke tubes arecompatible with factory ammunition that has been

loaded in compliance with SAAMI specifications,including magnum lead and steel shot loads, sabots andshotgun slug loads.

Replacement and additional tubes and wrenches areavailable from your Winchester Rifle and Shotgunsdealer, or by contacting the Winchester RepeatingArms Customer Service Department. See page 30for contact information.

choke tube selectionTo help you choose the correct choke tube for eachhunting and shooting situation, all Invector-Plus choketubes are inscribed on the side with the patterns theyproduce with both lead and steel shot. Each Invector tubealso has notches in the top rim of the tube (Figure 11).

21

N o N o tch es

F ive N o tch es

Fo u r N o tch es

th r ee N o tch es

two N o tch es

o N e N o tch

r im

N o tch es

Patter N with

Lead sh o t

Patter N with

steeL sh o t

ex te N d ed * * x- F u LL t u r k ey * *

i Fu L L *

i i i mP. mo d i F i ed Fu LL1

i i i mo d iF i ed Fu LL1

i i i i i mP. cyL iN d e r mo d iF i ed

i i i i i s kee t i mP. cyL iN d e r

N o N ot ch es cy L i N d er cy L i N d er

* Notforusewithsteelshot.Usinganover-tightchokeconstrictionwithsteelshotwillresultinanineffectiveblownpattern.

**ExtraFullSpecial,extendedwithports.Donotusewithsteelshot.

1Whenmorethanonechoketubeislistedforagivensteelshotpattern,usethemoreopenchokelistedforhighvelocity,largershotsizesteelloads.

FIGURE 11


24/36

22

These notches are a code to allow you to determine thechoke designation while the tube is installed. Rimnotches refer specifically to lead shot. Use the charts onpage 21 to cross-reference from lead to steel, anddetermine the appropriate tubes for your ammunition andhunting/shooting situation.

Several choke tubes are supplied with your shotgun.The choke tubes listed are also available as accessories.Remember, WinChoke, Standard Invector andInvector-Plus tubes are not interchangeable. Invector-Plustubes are for Winchester shotguns with back-boredbarrels only. Before removing or installing tubes, orreading the rim notch code, make sure your shotgun iscompletely unloaded.

choke tube removAl

1. Place the safety in the on safe position. Alwaysopen the action and make sure the shotgun iscompletely unloaded. Always keep the muzzlepointed in a safe direction.

2. Use the choke tube wrench to loosen the tube,turning it counterclockwise. Finger-twist the tubethe rest of the way out of the barrel.

choke tube instAllAtion

1. Place the safety in the on safe position. Alwaysopen the action and make sure the shotgun iscompletely unloaded. Always keep the muzzle pointedin a safe direction.

2. Before installing a tube, check the internal choke tubethreads in the muzzle, as well as the threads on thechoke tube to be sure they are clean. Lightly oil thethreads with a high-quality, lightweight gun oil.

3. Using your fingers, screw the appropriate tube into the

muzzle of the barrel, tapered end first, notched endoutward. When it becomes finger-tight, use the choketube wrench to firmly seat the tube.

NOTICE!theChoKetubeshouldbePeriodiCally

CheCKedtoassurethatitistightandFirMly

seated.beForeCheCKing,FollowallChoKetube

reMovalandinstallationsaFetyguidelines

Previouslyoutlined.

scope mountinG instructions

beForeMountingasCoPe,sightorother

aCCessoriestoyourshotgun,PlaCethe

saFetyintheonsaFePosition.oPentheaCtion

andMaKeCertainyourshotgunisCoMPletely

unloaded.KeePtheMuZZlePointedinasaFe

direCtion.FailuretoFollowthesewarningsCouldresultinseriousinjuryordeath.

Some Super X Pump shotguns are designed to accept ascope or other optical sight; usually these are turkey anddeer models. The receiver tops of some of these modelsare drilled and tapped for scope bases, while some models


25/36

23

are equipped with a cantilever scope base. If your shotgunhas a cantilever mount, follow the mounting instructionssupplied with your scope rings and/or scope. If yourshotguns receiver is drilled and tapped for scope mounts,four holes (in line, in pairs on top of the receiver) will bevisible. They are fitted with filler screws. If yours is drilledand tapped you must adhere to the following:

NOTICE!yourwinChestershotgunisdrilledand

taPPedFortheMountingoFbasesandringsto

aCCoMModateanaPProPriatesCoPeorsight.

alwaysusetheCorreCtbasesForthisshotgun

withtheaPProPriatelengthsCrewswhiChare

atleast1132"inlength.

1. Open the action and place your shotgun on a table orother safe/secure location. Protect the finish with ragsor other padding.

2. You should have two Super X Pump-compatible basesand four screws of at least 11/32" in length. Make sureyour bases are compatible with your Super X Pump.

3. Clean all oil, grease or dirt from the receiver top andfrom the scope base parts.

4. Position your shotgun in the upright position with the

top of the receiver upward.

5. Remove all four filler screws from the top of thereceiver using a very small, thin-bladed gunsmithing-type screwdriver.

6. Pre-position the bases on the receiver top to determinethe best orientation of the bases. Most bases havetransverse grooves cut into them that are offset fromthe middle. These are the grooves that the crossbolts inyour scope rings will pass through. The grooves areoffset to allow you to position the bases to fit thedesign/length of your scope and the placement ofthe scope front to back for proper eye relief. Placeboth grooves to the rear, both to the front, or onein each direction, depending on your scope anddesired position.

7. Once you know which configuration you will use,insert the screws through the bases and screw theminto the receiver top using the correct wrench orscrewdriver (usually a 3/32" hex wrench). You mustuse screws which are at least 11/32" in length to ensureproper thread engagement.

Many gunsmiths find it helpful to use a drop ofserviceable thread locking compound to assure thescrews stay tight. Make sure the compound does notget into the action. Be careful to assure that thethreads of each screw engage properly in the threads inthe receiver to prevent stripping the threads in thealloy receiver.

8. Tighten the screws snugly, but do not overtighten.

9. Mount your scope rings and scope as outlined in theinstructions supplied with your scope rings and/orscope. Always make sure you have the proper eye relief.


26/36

24

Always make sure that the saddle crossboltsand the cap bolts are fully tightened before usingyour shotgun.

extrA bArrels

beForeinstallingaCCessorybarrelson

yourshotgun,readtheFollowingguidelines

toensurethebarrel/shotgunCoMbination

issaFe.PlaCethesaFetyintheonsaFe

Position.oPentheaCtionandMaKeCertain

yourshotgunisCoMPletelyunloaded.KeePthe

MuZZlePointedinasaFedireCtion.Failureto

FollowthesewarningsCouldresultinseriousinjuryordeath.

The versatility of your new shotgun can be extended withan extra barrel. All shotgun barrels are interchangeablewithin a given gauge and chamber length. No specialfitting is required. However, some important restrictionsmust be observed:

Never use any other barrel from any othermanufacturer on your shotgun. Some other brandsmay seem similar, but the barrels are notinterchangeable.

cleAninG AnD mAintenAnce suGGestions

NOTICE!PleasetaKenoteoFtheFollowing

inForMationbeForeCleaningyourFirearM.

cleAninG pArts With speciAl Finishes

Be especially careful when cleaning firearms withcamouflage, Dura-Touch Armor Coating and otherspecial finishes. Always prevent these surfaces fromcoming in contact with cleaning solvents, barrel scrubbersand other strong chemicals. It is preferable to clean thesesurfaces with a light gun oil containing no solvents orwith a damp cloth and mild dish soap (be sure to keepwater out of the action). When cleaning your firearmsbore and action, protect the external finishes from any

contact with chemicals used. Also, avoid any contactbetween external finishes and other strong chemicals likethose found in DEET-containing insect repellents,sunscreens, etc. Damage to camouflage, Dura-Touch andother finishes caused by chemicals is irreversible and notrepairable.

beForePerForMingCleaningProCedures,

PlaCethesaFetyintheonsaFePosition.oPentheaCtionandMaKeCertainyourshotgun

isCoMPletelyunloaded.KeePtheMuZZle

PointedinasaFedireCtion.FailuretoFollow


ordeath.


27/36

25


CleaningyourshotguntoPreventsPrings,



KeePallaMMunitionawayFroMtheCleaning

area.nevertesttheMeChaniCalFunCtionoF

yourshotgunwithliveaMMunition.Failureto


injuryordeath.

cleAninG proceDures

Your Super X Pump will function better and more reliablyover a longer period of time if it is properly maintainedand kept clean. You should clean your shotgun after everyday of shooting, and more often if it becomes excessivelydirty. The barrel should be cleaned and the action wipedclean and oiled after every day of shooting.

Normal maintenance can be accomplished with the barrelstill attached to the receiver (oiling and wiping down).More careful cleaning requires removal of the barrel fromthe receiver (cleaning the barrel). A complete cleaningrequires removal of the bolt and trigger group.

If you encounter a function problem (tight action whenworking the forearm) be sure to give your firearm a

thorough cleaning to see if it solves the problembefore seeking the services of our service facility ora qualified gunsmith.

1. Place the safety in the on safe position. Open theaction and inspect the chamber and magazine to make

certain they do not contain any shells. Keep themuzzle pointed in a safe direction.

2 Remove the barrel as explained under Disassemblyon page 12.

3. Inspect the bore from both ends for leading and plasticresidue that often remain in the bores from the shotcups in modern shells. Leading and plastic residue willappear as longitudinal streaks and are usually morepredominant near the muzzle and just forward of the

chamber. A normal amount of either is common andnot serious.

4. If leading or plastic residue seems excessive you canremove it by brushing the bore with a brass brush.Soak the brush or spray the bore with a powdersolvent first. Scrub until clean. To prevent bristlesfrom breaking off, push the brush fully through thebarrel each time before pulling it back through.

MostsolventsarehighlyFlaMMable.weareye

ProteCtionandPraCtiCeaPProPriatesaFety

MeasureswhenworKingwithsolventstoavoid

seriousinjury.


28/36

26

5. After all leading and plastic residues have beenremoved, run a clean, dry patch through the bore.Follow this with a final, lightly oiled patch.

6. Inspect the barrel and chamber to be certain nopatches have inadvertently been left in them. Removeany that remain.

7. Reassemble the shotgun and wipe all exposed metalsurfaces with an oiled cloth making sure to wipe away

all finger marks where moisture could accumulate.Any dried oil in the receiver area should alsobe removed.

8. Lightly oil your firearm at the points describedon page 10. Regular, light oiling is extremelyimportant to the durability and reliable operationof your shotgun.

FIGURE 12

Trigger Group

Barrel

Firing Pin SpringFiring Pin

Slide Arms

ForearmTrigger Group Pin

Barrel Bracket

Bolt

Three-Shot

Adapter (Plug)

Magazine Three-shot

Adapter (Plug)

Magazine Tube

Choke Tube

Magazine Cap

Bolt Slide

Magazine Spring

Magazine Spring Retainer

Receiver


29/36

27

ADDitionAl DisAssemblY

One of the advantages of a Super X Pump is the ability todisassemble the action for cleaning. Under very harshweather conditions and in dirty environments justknowing that parts are clean and lightly oiled can add an

extra measure of confidence to your shooting experience.Make sure you have a clean place to work and a goodplace to put the components as they are disassembled(Figure 12, page 26).

removAloFthe bArrel

1. Unscrew and remove the magazine cap. Remember,always keep the end of the magazine pointed in asafe direction.

2. Slide the barrel forward, withdrawing the barrel fromthe receiver and disengaging the barrel bracket fromthe front end of the magazine tube.

3. Immediately screw the magazine cap back ontothe magazine tube at least three full turns.

removAloFthe triGGer Group

Removing the trigger group is another necessary

procedure in performing thorough maintenance of yourshotgun. It is easy to do, and removing it allows you toperform cleaning and maintenance whenever andwherever required. With both the trigger group and boltassembly removed, it is easy to wipe out any debris ormoisture that sometimes accumulates in the receiver.

The trigger group should be removed before you attemptto remove the bolt assembly.

1. Make sure the firearm is completely unloaded asexplained previously in this owners manual.

2. Cycle the action by sliding the forearm rearward and

then forward. This puts the hammer in the cockedposition. Place the safety in the on safe position.

3. If the barrel assembly has been removed, always besure to replace the magazine cap on the end of themagazine tube to prevent accidental disengagementof the magazine spring retainer.

4. Place your firearm with the trigger guard facing up ona suitable surface that will protect the receiver finish

and stock.5. Remove the trigger guard pin by pushing it out from

the left side of the receiver, the side opposite theejection port. Any sturdy pushing tool that is smallerin diameter than the pin and will not mar the finishis acceptable. Make sure you can maintain a goodgrip on the pushing tool and on your shotgun whileyou push.

6. Push the pin through sufficiently until it can be

grasped with your fingers. Pull it the rest of the wayout. If it cannot be removed with fingers, make sureyour pushing tool or punch has a diameter smallenough so that it will push the pin completely throughwithout the tool damaging the hole.


30/36

28

7. With the pin removed, lift the trigger group outof the receiver by lifting upward and pulling rearward(Figure 13).

DisAssemblYoFthe sliDe AnD bolt

1. Remove the barrel and trigger group as explainedearlier, but do not replace the magazine cap.

2. With the bolt assembly attached to the slide arm,simultaneously slide both assemblies forward and outof the front of the receiver. Note that as the boltassembly passes by the ejection port, there may besome resistance from the ejector spring. Carefullywork it past the resistance.

removAloFthe FirinG pin

1. Remove the bolt assembly from the shotgun asexplained previously.

2. Grasp the bolt assembly, bottom side up (flat side),and push the rear of the firing pin forward with your

forefinger. While holding the firing pin in thisposition, use your other hand to tilt the front end ofthe slide arm and move it slightly forward.

3. Lift up on the slide arm and disengage the curvedtongue on the slide arm from the groove in the firingpin. This detaches the slide arm from the bolt slide.

4. The firing pin is under spring tension and willsnap out the rear of the bolt when your forefingerreleases it. Control the pin as you remove the firingpin and spring.

For cleaning purposes no further disassembly is necessaryor recommended. Do not disassemble your Super X Pumpfurther than shown in Figure 12 on page 26. Doing so mayvoid your warranty. For repairs that require furtherdisassembly contact a Winchester Firearms AuthorizedService Center or a qualified gunsmith as explained underParts, Service, Repair and Questions on page 30.

AssemblYoFthe FirinG pin, boltAnD sliDe

1. Reinstall the firing pin spring over the firing pin.Either end of the spring can go on first.

2. Insert the firing pin/spring assembly into the rearopening of the bolt slide, pin end first.

FIGURE 13

After removing the

pin, tilt the rear of the

trigger guard group

up, then lift it out.


31/36

29

3. To reinstall the bolt assembly on the slide arm, pushor compress the knob end of the firing pin sufficientlyinto the hole in the bolt slide so that the large spacebetween the grooved knob and the flange on thefiring pin is centered in the round hole in thebolt slide.

4. Place the curved tongue, located on the slide arm,into the space between the knob and flange and

slowly release pressure on the end of the firing pin.Let the flange on the firing pin pull the tongue towardthe rear of the bolt assembly.

5. Remove the magazine cap.

6. Hold the slide arms and bolt/slide arm assembliestogether (Figure 14). Start the forearm assembly ontothe magazine tube.

7. Carefully guide the slide arms and bolt/slide armassemblies into the front of the receiver. As theassemblies enter the receiver, slide them fullyrearward (Figure 15).

reinstAllAtionoFthe triGGer Group

1. The bolt assembly, slide arms and forearm shouldbe attached to the receiver before installing thetrigger group.

FIGURE 15

Carefully guide the bolt assembly on the

slide arms into the receiver.

FIGURE 14

Position the bolt assembly on the slide arms.


32/36

30

2. Ensure the hammer is in the cocked position bypushing it straight back until it locks into placeand the safety is in the on safe position.

3. Turn the shotgun over with the open bottom of thereceiver facing upward. Hold the trigger group at an

angle to the receiver (about 45 degrees) and thenengage the front tabs on the trigger group with thecorresponding slots in the magazine throat at theforward end of receiver opening as shown in Figure 13on page 28.

4. Carefully insert the front of the trigger group into thereceiver opening, then lower the rear into the receiveropening until it is parallel with the receiver. It may benecessary to slide the forearm into different positions

until the trigger group fits flush into the receiver.When properly installed it will fit easily and thetrigger group pin hole will be in alignment.

NOTICE!beCareFulwhenreinstallingthe

triggergrouP.neverForCePartsintoPosition.

donotatteMPttoinstalltheboltasseMbly

aFterthetriggergrouPisinstalled.Failure

toFollowtheseinstruCtionsMaydaMage

yourFirearM.

5. Align the trigger group with the hole in the receiverand push the trigger group pin through the receiveruntil it is flush with both sides of the receiver. Thepin should pass through easily with little force.

If significant resistance is felt, remove the triggergroup and repeat step one.

Your firearm is now fully assembled. Immediately confirmthat the safety is in the on safe position. Take time towipe down and clean all external surfaces as explained

under Cleaning and Maintenance Suggestions onpage 23.

NOTICE!donottaKeyourFirearMsaCtionaPart

beyondwhatisexPlainedinthisowners

Manual.thisisasPeCialiZed,FinelyFitted

MeChanisM;anyatteMPttodisasseMblethe

innerMeChanisMMayMaritForliFe.itis

unneCessary,andMaydodaMagetotheinner

MeChanisMtodisasseMbleitForroutine

Cleaningandoiling.oFCourse,MisFortunes

(suChasdroPPingyourFirearMinwater)

requireaPProPriateattention,andinsuCh

CirCuMstanCeswereCoMMendyouiMMediately

taKeyourFirearMtoaqualiFiedgunsMith.

other cleAninG suGGestions

After extended periods of heavy use, your firearm should

be taken to a qualified gunsmith to have the actiondisassembled for professional cleaning and lubrication.


33/36

31

pArts, service, repAirAnD Questions

If your Winchester firearm should ever need service orrepair, it is often best to utilize one of our AuthorizedRepair Centers. In some cases it is appropriate to use theWinchester Repeating Arms Service Center in Arnold,

Missouri. A list of Authorized Repair Centers wasincluded with your new firearm. If you need a new listing,contact us. We can help you determine the best place toservice your firearm.

In order to avoid delays, it is important to never send yourfirearm directly to our facility without direct authorizationfrom one of our service specialists. This avoids possibledelays in obtaining service. Contact us at (800) 322-4626for details on how to receive service before sending

your firearm.Parts listings, Authorized Repair Center lists,service procedures, service/repair form and generalproduct information are also found on the Web at:winchesterguns.com.

When returning your firearm for servicing, you must dothe following:

1. Be sure it is completely unloaded.

2. Remove the scope or other optics.3. Package it securely in a cardboard container.

4. Enclose the service/repair form available atwinchesterguns.com or a letter that clearly describesthe trouble experienced, the ammunition used and the

repairs desired. Also include your name and a daytimephone number where you can be reached.

5. If convenient, send a copy of the service/repair formor letter to us separately.

6. Never return ammunition with your firearm. It is

against postal and most commerce regulations.

pArts , service, repAir stAtus AnD

technicAl Questions

Winchester Repeating Arms Parts and Service3005 Arnold Tenbrook RoadArnold, MO 63010-9406(800) 322-4626

GenerAl proDuct AnD historicAl Questions

Winchester Repeating Arms Customer Service275 Winchester AvenueMorgan, UT 84050-9333(800) 945-5237

PartsareMadeForwinChesterbrandFirearMs

ManuFaCturedbyorForwinChesterrePeating

arMs,andshouldnotbeusedinotherFirearMs,eventhoughModelsMaybesiMilar.iMProPerly

FittedPartsMaybedangerous.


34/36

32

Website inFormAtion

An information resource for Winchester Repeating Armsis found on the World Wide Web.

List of Authorized Repair Centers.

Customer Service information. Firearm Service/Repair Form.

Answers to many technical and historical questions.

Links to helpful sites.

Go to: winchesterguns.com


35/36


36/36

Winchester Repeating Arms

275 Winchester Avenue

Morgan, UT, U. S. A. 84050-9333

winchesterguns.com

Winchester is a registered trademark of Olin Corporation.

WINCHESTER SUPER X PUMP, PUMP-ACTION SHOTGUN OWNER’S MANUAL

Documents

Transcript of WINCHESTER SUPER X PUMP, PUMP-ACTION SHOTGUN OWNER’S MANUAL