Winchester - 3 Door 4 Drawer Wardrobe
Transcript of Winchester - 3 Door 4 Drawer Wardrobe
Dimensions
Width - 126.3cmDepth - 52cmHeight - 184.5cm
Issue 1 - 10/03/10
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 160 1490
Winchester - 3 Door 4 Drawer WardrobeAssembly Instructions - Please keep for future reference
656/6988656/7035
Safety and Care AdviceImportant – Please read these instructions fully before starting assembly
• Check you have all the components and tools listed on pages 2, 3 and 4.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor.
• Parts of the assembly will be easier with 2 people.
• We do not recommend the use of power drill/drivers for inserting screws,
as this could damage the unit. Only use hand screwdrivers.
• Dispose of all packaging carefully and responsibly.
• When handling mirror care must be taken to ensure it is not knocked or damaged.
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Care and maintenance
1
Large drawer front x 2 (71.3 x 19cm)
Bottom panel x 1 (112.3 x 48.6cm)
Components - PanelsPlease check you have all the panels listed below
2
Top panel x 1 (126.3 x 52cm)3
Left side panel x 1 (49.5 x 182.2cm)
2Right side panel x 1 (49.5 x 182.2cm)
1
Back panel x 1 (76.8 x 174.1cm)
5
10
Back panel x 1 (37.5 x 174.1cm)
6
Right hinge frame x 1 (5.3 x 182.2cm)
7
4
Right drawer side x 4 (35 x 10cm)
11 Left drawer side x 4 (35 x 10cm)
12
Left hinge frame x 1 (5.3 x 182.2cm)
8
Large drawer back x 2 (70.6 x 10cm)
13
Bottom plinth x 1 (105.4 x 5.3cm)
9
Handle x 9 (10.5 x 1.9cm)15Large drawer base x 2 (71 x 33.9cm)
14
If you have damaged or missing components, call the Customer Helpline: 0870 160 1490
Vertical partition wall x 1 (48.4 x 171.3 cm)
Components - PanelsPlease check you have all the panels listed below
Small horizontal partition shelf x 1 (35.7 x 48.4cm)
17
22
Small drawer back x 2 (31.3 x 10cm)
18
Small drawer front x 2 (37 x 19cm)
19
Large horizontal partition shelf x 1 (75 x 48.4cm)
16
Right door x 1 (37 x 132cm)23 Middle mirror door x 1 (37 x 132cm)
24
Small drawer base x 2 (31.7 x 33.9cm)
20
Left door x 1 (37 x 132cm)25
Shelf x 2 (35.6 x 47.6cm)21
Right side
3
Please check you have all the fittings listed below
Feet x 4
Tools required
A
Screw x 48
E
8/30mm Wooden dowel x 48
B
Small locking nut x 8
H
6/30mm Wooden dowel x 16
C
Key x1
R
L
I
Drawer base support x 4
Q
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
100 20 30 40 50 60 70 80 90 100
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170105
Hanger rail support x 2
Hanger rail x 1 14mm Screw x 2 Door stop x 1
V
9mm Screw x 16
F
Door hinge x 6 Wall strap x 1Hinge plates x 6
13mm Screw x 1 12mm Screw x 8
W
Nail x 50
D
20mm Screw x 16
K
Underlay x 2
ORunner left B x 4
M
P
Runner right B x 4
N
Shelf support x 8U
X
Z ZZY Z
Runner left A x 4
L
Large locking nut x 40
G
Plastic dowel x 16
J
50mm Screw x 3
R
Runner right A x 4
S
35mm Screw x 18
T
Components - Fittings
Phillips screwdriver (medium & large)
Flatblade screwdriver (medium)
Hammer
Spirit level
2 34
Ruler/tape measure
4
Attaching runners
a: Position runners T 15mm in from front edge of the left side panel 1 .
Slide top of the runners back.
Fix through holes shown using screws C .
Assembly InstructionsStep 1
Attaching runners
a: Position left runner A L and right runner A R on to the drilled holes of the left and right side panels 1 and 2 and the left side of vertical partition wall 22 .
Fix through holes shown using screws F and Z 4.
4
a:
c:
E
E
B
E
E
E
1
2
3
22
R
R
F
L
221
2
A
E
Left side
LF
b: Right side
R
b: Turn over the vertical partition wall 22 and attach runners A L as shown using screws F and Z 4.
c: Attaching feet
Position plastic feet A to the left and right side panels 1 , 2 from below and fix them using the hammer.
F
22
5
L
Z 4
Z 4
Preparation for the attaching of horizontal partition shelf and bottom panel
Insert screws E into the drilled holes of the left and right side panels 1 and 2 , top panel 3 and vertical partition wall (from both sides) 22 and fix them.
Insert wooden dowels B into the bottom panel 4 as shown on the picture.
Step 2
Attaching runners
a: Position runners T 15mm in from front edge of the left side panel 1 .
Slide top of the runners back.
Fix through holes shown using screws C .
Assembly Instructions
Attaching horizontal partition shelves to the vertical partition wall
Insert wooden dowels B into the vertical partition wall 22 , place horizontal partition shelves 16 , 17 on to the screws E , align correctly and insert large locking nuts G into the drilled holes and turn them clockwise to lock.
Step 3
16
22
17
B
G
G
Step 4
a: Place bottom panel 4 to the partition wall
22 and screw the screws Q using the key I . Align correctly and insert large locking nuts G .
b: Insert wooden dowels B into the bottom panel 4 and partition shelves
16 17 and place left and right side panels 1 , 2 . Align correctly
and insert large locking nuts G and turn them clockwise to lock.
a:
b:
6
B
11 mm
Q
I
G
G
16
2
1
22
1617
417
B
B
22
4
Q
G
G
Attaching runners
a: Position runners T 15mm in from front edge of the left side panel 1 .
Slide top of the runners back.
Fix through holes shown using screws C .
Assembly Instructions
Frame assembly
Insert screws E in to the frames 7 , 8 , 9 .
Insert wooden dowels B as shown, align correctly and insert large locking nuts G in to the frame 9 , place the frames 7 , 8 and turn them
clockwise to lock.
Step 67
9
8
E
E
7
8
E
Step 5
9
E
E
G
G
B
B
G
B 11 mm
7
Attaching runners
a: Position runners T 15mm in from front edge of the left side panel 1 .
Slide top of the runners back.
Fix through holes shown using screws C .
Assembly InstructionsStep 7
Step 8
Step 9
Attaching top panel
Insert wooden dowels B into the top edges as shown, align correctly and insert large locking nuts G into left and right side panels 1 and 2 and vertical partition wall 22 , place the top panel 3 and turn locking nuts
clockwise to lock.
Attaching back panels
With help, carefully lay wardrobe down.
Position back panels 5 , 6 in position on
the back of wardrobe. Position nails D 5 mm in from side edge of the back panels 5 , 6 with distance 100 mm between each other. Fix them using the hammer.
2
D
5 mm
100 mm
6
8
5
1
G
G
B
1
3
2G
22
G
4
Note: You must ensure the wardrobe is square before attaching the back panels.
B
11 mm
B
11 mm
Attaching the frame
Insert wooden dowels B into the edge of the left and right side panels 1 , 2 .
Align correctly and insert large locking nuts G into left and right side panels 1 , 2 and bottom panel 4 , place the frame
and turn locking nuts clockwise to lock.
B
B
Attaching runners
a: Position runners T 15mm in from front edge of the left side panel 1 .
Slide top of the runners back.
Fix through holes shown using screws C .
Assembly InstructionsStep 10
Drawer assembly
a: Insert screws E into large or small drawer front 10 , 19 .
b: Insert wooden dowels B in to large or small drawer front 10 , 19 . and place left and right drawer sides 11 , 12 .
c: Slide large or small drawer base 14 , 20 iinto the grooves.
d: Place large or small drawer back 13 , 18 onto sides.
e: Align correctly and insert small locking nuts H into left and right drawer sides 11 , 12 and turn them clockwise to lock.
f: Insert plastic dowels J into left and right
drawer sides 11 , 12 and large or small drawer back 13 , 18 and fix it together using the hammer.
g: Position left and right runners B M , N on to left and right drawer sides 11 , 12 , fix using screws K .
10
14
13
K
M
N
K
J
JH
a: b:
c: d:
e: f:
g:
E
12 12
12
12
11 11
11
11
1313
K
K
19
2018
18
18
11
12
B
1910
continued on next page
9
Attaching runners
a: Position runners T 15mm in from front edge of the left side panel 1 .
Slide top of the runners back.
Fix through holes shown using screws C .
Assembly Instructions
Attaching hanger rail
Insert hanger rail supports U and place the hanger rail Z .
Fitting hinges to doors and door stop
Position 2 hinge plates V into left and right side panels 1 , 2 and partition wall 22 . Fix using supplied screws.
Position door stop Z 3 onto the underside of the top panel 3 , fix using screws Z 2.
Step 11
Placing shelves
With help, carefully stand wardrobe upright.
Warning: The wardrobe is heavy. Lift with care.
Position shelf supports T and place the shelves 21 .
Step 12
Step 13
P
S
15
15
S S
Z
U
10
h: i:
T21
V
1
222
P
P
T
Z
Z
3
h: Large drawers only: Position 2 drawer base supports P onto the underside of the large drawers as shown. Fix using supplied screw.
i: All drawers: Attach handles 15 to drawer fronts using screws S .
2
3
32 mm
Step 10 - continued
Attaching runners
a: Position runners T 15mm in from front edge of the left side panel 1 .
Slide top of the runners back.
Fix through holes shown using screws C .
Assembly Instructions
W
Hanging doors
With help, slot door hinges W onto hinge plates V and click into position.
Repeat for all doors.
Hinge adjustment
To move doors up or down, in or out, left or right: loosen screws as shown and move doors up or down, in or out, left or right as required.
Retighten screws.
Step 14
Position 2 door hinges W into left, middle mirror and right doors 23 , 24 , 25 , fix using supplied screws.
Step 15
Attaching handles to the doors
Attach handles 15 to doors 23 , 24 , 25 using screws S .
Repeat this step with all doors 23 , 24 , 25 .
Step 16
Step 17
25
15
24 23
S
V
click!
25 24 23W
Warning: The mirror door. Handle with care.
Warning: The mirror door. Handle with care.
11
Attaching runners
a: Position runners T 15mm in from front edge of the left side panel 1 .
Slide top of the runners back.
Fix through holes shown using screws C .
Assembly Instructions
Fix wall strap X to top of wardrobe using screw Y and underlay O .
Assembly is complete.
Fixing to wall
It is recomended that the wardrobe is fixed to a wall.
Mark fixing hole onto wall. Drill a hole and insert a suitable wall plug. Fix wall strap X using a suitable screw.
With help, move wardrobe into position.
Step 18
Inserting drawers
Insert the drawers with the move from down to up as shown and ensure that wheels fit onto left and right runners L , R .
Step 19
O
Y
X
12
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 160 1490
Home Retail Group Plc, 489 - 499 Avebury boulevard, Milton Keynes, MK9 2NW
Warning: The wardrobe is heavy. Lift with care.
Warning: Before drilling, check wall for hidden pipes and cables.
Note: Wall fixings are not supplied with this unit.
The correct type of fixing must be used for your wall, seek professional advice if in doubt.
RL
X