WiMAX OMC Operation Guide 20090216 a 1.0
Transcript of WiMAX OMC Operation Guide 20090216 a 1.0
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
1/98
Product Name Confidentiality
WiMAX RNP For Internal Use Only
Product Version
98 pages in total1.0
WiMAX OMC Operation Guide
For Internal Use Only
Prepared by: Hu Jun, Ge Yonghui, and Xu Jun Date 2008-12-19
Reviewed by: Date
Reviewed by: Date
Approved by: Date
Huawei Technologies Co., Ltd.
All rights reserved.
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
2/98
WiMAX OMC Operation Guide INTERNAL
Change History
Date RevisionVersion
Description Reviewed by: Author
2009-01-07 1.0 Modified according to
the review comments.
Jiang Bo, Yang Fan, Zou
Meizhong, Chen Dehai, and
Hong Weifeng
Hu Jun, Ge Yonghui,
and Xu Jun
2013-06-21 HUAWEI Confidential Page 2, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
3/98
INTERNAL
Content
1 Overview...................................................................................10
1.1 Guide to Operations in the WiMAX O&M center.................................................................................................10
1.2 Introduction to the WiMAX Networking................................................................................................. ......... ....10
1.3 Introduction to the Environment of the O&M center........................................................................................... .11
1.4 Code of Conduct and Precautions......................................................................................................... .......... ......12
2 Operation and Maintenance of the DBS3900 LMT.........................13
2.1 Introduction to the DBS3900 Local Maintenance Terminal (LMT)......................................................................13
2.2 Installing and Starting the DBS3900 LMT............................................................................................................13
2.3 R1 Signal tracing for a Single DBS3900 User................................................................................................... ...16
2.4 Signal tracing for a Single DBS3900 User............................................................................................................18
2.5 Viewing the Saved R1 and R6 Signaling Files......................................................................................................20
2.6 Running DBS3900 MML Commands................................................................................................................ ...22
2.7 User Information Monitoring.................................................................................................................... .......... ..27
2.8 Carrier Tracing.......................................................................................................................................................30
3 Operation and Maintenance of the WASN9770 of the LMT.............33
3.1 Overview of the WASN9700 LMT........................................................................................................................33
3.2 Installing and Starting the WASN9770 LMT..................................................................................................... ...33
3.3 R3 and R6 Signaling Monitoring Through the WASN9770 LMT................................................................. .......36
3.4 Running WASN9770 MML Commands................................................................................................................38
4 Operation Management of the M2000..........................................41
4.1 Overview of the M2000.........................................................................................................................................41
4.2 Staring the M2000 Client..................................................................................................................... ......... ........41
4.3 Operations of Traffic Measurement Data on the M2000 Client............................................................................46
4.3.1 Creating the Traffic Measurement Task...........................................................................................................46
4.3.2 Obtaining Traffic Measurement Data..............................................................................................................48
4.4 Alarm Querying Through the M2000................................................................................................................... .55
4.4.1 Querying Alarms by Severity....................................................................................................................... ...55
4.4.2 Querying Alarms by NEs.................................................................................................................................57
4.5 Running M2000 MML Commands................................................................................................................. ......61
5 Operations of the WCS................................................................68
5.1 Overview of the WCS............................................................................................................................................68
2013-06-21 HUAWEI Confidential Page 3, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
4/98
INTERNAL
5.2 BTS Parameter Batch Processing..........................................................................................................................68
5.3 Neighbor Cell Adding............................................................................................................................................76
5.4 Radio Parameter Importing and Exporting............................................................................................................86
5.4.1 Importing BTS Radio Parameters....................................................................................................................86
5.4.2 Exporting BTS Radio Parameters....................................................................................................................93
6 Summary...................................................................................98
2013-06-21 HUAWEI Confidential Page 4, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
5/98
INTERNAL
Figures
Introduction to the WiMAX network architecture.............................11
Selecting a language......................................................................14
User Login dialog box.....................................................................14
Entering the related information.....................................................15
User Login dialog box.....................................................................16
Logging in to the interface of R1 signal tracing................................17
Interface of real-time R1 signal tracing...........................................18
Logging in to the interface of R6 signal tracing................................19
Interface of real-time R1 and R6 signal tracing................................20
Selecting a signaling file................................................................20
Trace Viewer dialog box..................................................................21
Message Browser dialog box...........................................................22
Interface of running MML commands...............................................23
Interface of entering MML commands..............................................24
Common Maintenance interface......................................................25
Operation Record interface.............................................................26
Help Information interface..............................................................27
User Information Monitoring dialog box..........................................28
Interface of the user information displayed in a list.........................29
Interface of the user information displayed in a chart......................29
Carrier Frequency Monitoring dialog box.........................................31
Interface of the carrier information displayed in a list......................32
Interface of the carrier information displayed in a chart...................32
User Login dialog box.....................................................................34
2013-06-21 HUAWEI Confidential Page 5, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
6/98
INTERNAL
Related interfaces for entering the NE information..........................35
User Login and Select Version dialog boxes.....................................36
MS Tracing dialog box....................................................................37
Interface of real-time R3 and R6 signal tracing................................38
Interface of running WASN9770 MML commands..............................39
Common Maintenance interface......................................................40
Login dialog box............................................................................42
Modify Server Information dialog box..............................................43
Login progress bar.........................................................................44
Menu of Topology...........................................................................45
Main Topology interface.................................................................45
Measurement Settings...................................................................47
Information dialog box...................................................................47
Measurement Status......................................................................48
Selecting Query Result...................................................................49
Query Result interface...................................................................49
Object Settings interface................................................................50
Counter Settings interface..............................................................51
Other Settings interface.................................................................52
Measurement report displayed in a table.........................................53
Measurement report displayed in a line chart..................................53
Measurement report displayed in a bar chart...................................54
Saving measurement reports..........................................................54
Alarm Board..................................................................................55
Current Fault Alarms [All objects] dialog box.................................56
Alarm Detail Information and Process Advice interfaces...................56
Detail Information dialog box.........................................................57
Menu of Topology...........................................................................58
Alarm information about NEs..........................................................58
Querying alarm information about NEs............................................59
2013-06-21 HUAWEI Confidential Page 6, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
7/98
INTERNAL
Current Fault Alarms Object [bsc41] dialog box...........................60
Status of alarm information............................................................61
MML Command interface................................................................62
Selecting NE(s)..............................................................................62
Entering MML commands................................................................63
Entering MML commands................................................................64
Running MML commands................................................................65
History Command interface............................................................65
Help Info interface.........................................................................66
Exporting history operations..........................................................67
Main menu of the M2000................................................................69
New Project dialog box...................................................................69
Selecting NEs................................................................................70
Selecting a parameter....................................................................71
Modifying parameters....................................................................72
Saving modified parameters...........................................................73
Checking validity of modified parameters........................................74
Applying modified parameters........................................................75
Synchronizing NEs.........................................................................76
Main menu of the M2000................................................................77
Neighbor relations.........................................................................78
Add Neighbor Carrier interface.......................................................79
Add Neighbor Carrier interface.......................................................80
Check Consistent Report interface..................................................81
Check Consistent Report interface..................................................82
Apply interface..............................................................................83
Apply complete interface................................................................84
Synchronizing NEs.........................................................................85
Synchronizing NEs.........................................................................86
Importing radio parameters............................................................87
2013-06-21 HUAWEI Confidential Page 7, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
8/98
INTERNAL
Selecting the directory for importing radio parameters....................88
Checking the radio parameters to be imported................................89
Importing radio parameter scripts..................................................90
Importing radio parameter scripts..................................................91
Synchronizing NEs.........................................................................92
Synchronizing NEs complete...........................................................93
Exporting radio parameters............................................................94
Selecting the directory for exporting radio parameters....................95
Progress of exporting radio parameters..........................................96
Exporting radio parameters complete.............................................97
2013-06-21 HUAWEI Confidential Page 8, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
9/98
INTERNAL
WiMAX OMC Operation Guide
Key words: MML commands, traffic measurement, user information monitoring, single-user signal tracing,
carrier tracing, radio parameter, and operation and maintenance
Abstract: This document is for the WiMAX RF engineers to operate the equipments and software. It describes
how to use the common tools such as LMT, M2000, and WCS. It covers R1 and R6 signal tracing, MML
commands, user information monitoring, carrier tracing, traffic measurement task creating, traffic measurement
data obtaining, alarm querying, BTS parameter batch processing, neighbor cell adding, and BTS radio parameterimporting and exporting.
Acronyms and Abbreviations
Acronym andAbbreviation
Full Name
LMT Local Maintenance Terminal
MML Man Machine Language
RTWP Received Total Wideband Power
WCS WiMAX Configuration Solution
2013-06-21 HUAWEI Confidential Page 9, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
10/98
INTERNAL
1 Overview1.1 Guide to Operations in the WiMAX O&Mcenter
This document is helpful for the WiMAX RF engineers to operate the common tools. It
describes how to use the BTS LMT, GW LMT, M2000, and WCS. The contents are listed as
follows:
1. Rule in the O&M center
When working in the O&M center, the RF engineers should comply with the relatedregulations and precautions.
2. Operation and maintenance of the DBS3900 LMT
This section describes how to perform the R1 and R6 signal tracing for a single user, MML
command running, user information monitoring, and carrier tracing of the DBS3900 LMT.
3. Operation and maintenance of the WASN9770 LMT
This section describes how to perform the R6 and R3 signal tracing for a single user and run
MML commands of the WASN9770 LMT.
4. Operation management of the M2000
This section describes how to create the traffic measurement task, obtain the traffic
measurement data, query BTS alarms, and run M2000 MML commands on the M2000 client.
5. Operation of the WCS
This section describes how to perform the BTS parameter batch processing, add neighbor
cells, and import and export BTS radio parameters.
1.2 Introduction to the WiMAX NetworkingThe following figure shows the WiMAX networking. The GW is connected to the BTS
equipment over the R6 interface and connected to the M2000 Server of the AAA Server over
the R3 interface. The WiMAX RF engineers are mainly involved in operations in the local
O&M center (using the LMT) or central O&M center (using the M2000).
2013-06-21 HUAWEI Confidential Page 10, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
11/98
INTERNAL
Figure 1.1 Introduction to the WiMAX network architecture
For different WiMAX networks, BTSs, and GWs are assigned with different IP addresses,
different user names and passwords, which are managed and assigned by the O&M center
management staff, who should comply with the relevant regulations.
1.3 Introduction to the Environment of theO&M center
This document describes how to use the common tools such as the BTS LMT, M2000, and
Nastar. This section will give an example.
The O&M center is installed with a set of GWs, the AAA Server, and the M2000.The
following table lists the IP addresses, user names, and passwords for the NEs:
The Nastar uses the data collection tool to collect data. The user name and password are the same as
those of the FTP server on the M2000. By default, the user name is ftpuser, and the password is notrequired.
Pls confirm and double check the IP address, user name, and password for each NE.
2013-06-21 HUAWEI Confidential Page 11, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
12/98
INTERNAL
1.4 Code of Conduct and Precautions
When working in the O&M center, RF engineers should comply with the followingregulations and precautions:
1. Be on and off duty on time. Follow the regulations to enter and exit the O&M center.
2. Do not drink or eat in the O&M center. In general, we are not allowed to bring cups orglasses into the O&M center.
3. All the user names, passwords, and IP addresses for different OM clients should be
assigned and managed by the manger of the O&M center.
4. Do not operate if not required, such as resetting boards and modifying system
parameters.
5. The manager of the O&M center is responsible for ensuring availability of the operation
platform. For example, ensure that the free disk space of the M2000 server is sufficient.Send the traced data files to the RF engineers in time. Delete the traced data files on the
client in time. Otherwise, too much disk space is occupied.
6. Due to the high safety requirements for the operation platform, do not copy files by using
any storage medium on the operation platform. To upload script files to the operation
platform and download operation result files to wer own laptop, connect wer laptop tothe server with the Ethernet cable of the internal maintenance network segment.
Do not connect any USB storage medium directly to any server of the O&M center.
If any USB storage medium is directly connected to the M2000, AAA, or other system
servers, the PC may be infected by viruses.
2013-06-21 HUAWEI Confidential Page 12, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
13/98
INTERNAL
2 Operation and Maintenance ofthe DBS3900 LMT
2.1 Introduction to the DBS3900 LocalMaintenance Terminal (LMT)
The DBS3900 LMT is used to operate and maintain a single DBS3900. The network planningand optimization engineer need to use the LMT to modify parameters, trace signaling, and
observe carrier status. On the PC, install the LMT software with default configurations. To
use the DBS3900 LMT, the R6 interface can be connected to the BBU local maintenance portthrough the router.
Precautions:
1. We need to select a language for installing the software, for example, English or
Chinese. Ensure that the software version is consistent with the BTS version.
2. The serial number of the version should be WiMAX BTS.
3. The installation type should be typical installation.
2.2 Installing and Starting the DBS3900 LMTThe following figure shows the dialog box displayed for selecting a language during the
installation of the LMT.
2013-06-21 HUAWEI Confidential Page 13, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
14/98
INTERNAL
Figure 1.1 Selecting a language
To start the BTS LMT, do it as follows:
Step 2 After the LMT is installed, click the button in the red rectangle to start the LMT, as shown inFigure 1.1.
Figure 1.1 User Login dialog box
Step 3 ClickAdd orModify in the red circle, as shown in Figure 1.1. A dialog box is displayed.
2013-06-21 HUAWEI Confidential Page 14, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
15/98
INTERNAL
EnterOffice (generally the BTS name), IP Address (maintenance IP address if wer notebookPC is connected to the BBU maintenance port or service IP address if wer notebook PC is
connected to the service port), and NE Type (WiMAX BTS for the DBS3900).ClickOK, and
then clickClose.
Figure 1.1 Entering the related information
Step 4 After entering the related information, select Local to log in, as shown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 15, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
16/98
INTERNAL
Figure 1.1 User Login dialog box
On the LMT, the network planning engineers usually perform the following operations:
2. R1 signal tracing for a single user
3. R6 signal tracing for a single user
4. Commands running
5. Single-user information monitoring
6. Carrier tracing
2.3 R1 Signal tracing for a Single DBS3900User
For problems involving network access, access failure, and handoff of NEs such as terminals
and the BS, the network planning and optimization engineer need to query the R1 signaling ofthe air interface.
To perform the R1 signal tracing for a single user, do it as follows:
Step 1 After logging in to the LMT, clickMaintenance (1), and then double-clickR1 User Tracing(2). In the displayed dialog box, select All (3) of the Direction dropdown list box, enterMAC(4) for the terminal to be traced, click Select All ofTrace Message Type (5), and then click
the button in the red rectangle (6) to select the path to save the signaling files automatically.ClickOK.
2013-06-21 HUAWEI Confidential Page 16, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
17/98
INTERNAL
Figure 1.1 Logging in to the interface of R1 signal tracing
Step 2 After logging in to the interface of R1 signal tracing, the real-time tracing can be performed if
the terminal has R1 signaling interaction with the BTS, as shown in Figure 1.1. Double-clickone entry, and then we can view the detailed information about the signaling.
2013-06-21 HUAWEI Confidential Page 17, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
18/98
INTERNAL
Figure 1.1 Interface of real-time R1 signal tracing
In Step 1Figure 1.1, Auto Save File is selected by default. If we do not specify a path, all traced R1
signaling files are saved in the default path, for example,
D:\HW LMT\client\output\WiMAX BTS\DBS3900 WiMAX V300R002C01B034\trace.
2.4 Signal tracing for a Single DBS3900 UserFor checking network access, access failure, and handoff of NEs , RF engineers need to query
the R6 signaling. To perform the R6 signal tracing, we can do it as follows:
Step 1 Double-clickR6 User Tracing (1). In the displayed dialog box, select Up (2) of the Directiondropdown list box, enterMAC (3) for the terminal to be traced, clickSelect All ofTraceMessage Type (5), and then click the button in the red rectangle (5) to select the directory for
saving the signaling files automatically. ClickOK.
2013-06-21 HUAWEI Confidential Page 18, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
19/98
INTERNAL
Figure 1.1 Logging in to the interface of R6 signal tracing
Step 2 The interface of R6 signal tracing is similar to that of R1 signal tracing. Select Tile
horizontal, and then we can view the R1 and R6 signal tracing results at the same time forcomparison and analysis. Right-click on the interface of R1 or R6 signal tracing, and select
Save All Messages to save the related files to the specified directory.
2013-06-21 HUAWEI Confidential Page 19, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
20/98
INTERNAL
Figure 1.1 Interface of real-time R1 and R6 signal tracing
In Step 1Figure 1.1, Auto Save File is selected by default. If we do not specify a path, all traced R6signaling files are saved in the default path, for example,
D:\HW LMT\client\output\WiMAX BTS\DBS3900 WiMAX V300R002C01B034\trace.
2.5 Viewing the Saved R1 and R6 SignalingFiles
When the R1 and R6 signaling files are saved in .tmf format, we can open those .tmf files
offline to view and analyze the signaling. The steps are as follows:
Step 1 Double-click a signaling file.
Figure 1.1 Selecting a signaling file
2013-06-21 HUAWEI Confidential Page 20, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
21/98
INTERNAL
Step 2 After the file is opened, we can view and check the signaling process.
Figure 1.1 Trace Viewer dialog box
Step 3 Double-click an entry. The Message Browser dialog box is displayed, and then we can viewand analyze the TLV encoding information of the signal.
2013-06-21 HUAWEI Confidential Page 21, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
22/98
INTERNAL
Figure 1.1 Message Browser dialog box
2.6 Running DBS3900 MML Commands
When RF engineers need to query data, record data, and modify parameters of the BTS byusing the LMT, learning how to run MML commands is required. To run a MML command,
do it as follows:
Step 1 After logging in to the LMT, clickMML Command, as shown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 22, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
23/98
INTERNAL
Figure 1.1 Interface of running MML commands
Step 2 Click or press the Enter button. Then, the interface for entering commands is displayed.
The items in red font are mandatory, and the items in black are optional. When enter related
information, the corresponding command is displayed in the text box. Click or press F9
to run the command.
2013-06-21 HUAWEI Confidential Page 23, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
24/98
INTERNAL
Figure 1.1 Interface of entering MML commands
Step 3 In the displayed Common Maintenance interface, we can query whether the command runssuccessfully, as shown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 24, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
25/98
INTERNAL
Figure 1.1 Common Maintenance interface
Step 4 ClickOperation Record to query history command records. We can view the time, status,and result of each operation, as shown in Figure 1.1.We can also right-click the entry, and then
select Save to save operation logs.
2013-06-21 HUAWEI Confidential Page 25, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
26/98
INTERNAL
Figure 1.1 Operation Record interface
Step 5 ClickHelp Information to query the relation information about one command such as thefunction, precaution, and parameters, as shown in Figure 1.1. We can add, delete, or modify
parameters even if we are not familiar with the command.
2013-06-21 HUAWEI Confidential Page 26, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
27/98
INTERNAL
Figure 1.1 Help Information interface
2.7 User Information MonitoringTo confirm problems of terminal or get some information from terminal, the engineers need to
monitor user information, including the total number of uplink and downlink service packets,
RSSI, CINR, and MCS. All information can be displayed in tables and figures. The following
table lists the task types that can be monitored.
Task ID Task Type
11 Uplink total packets number
12 Uplink bad packets number
13 MS TX power (dBm)
14 Uplink CINR (dB)
15 Downlink CINR (dB)
16 Uplink RSSI (dBm)
17 Downlink RSSI (dBm)
18 Uplink MCS (dB)
19 Downlink MCS (dB)
2013-06-21 HUAWEI Confidential Page 27, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
28/98
INTERNAL
Task ID Task Type
110 Outer-loop threshold of uplink qpsk 1/2
The procedure is as follows:
Step 1 After logging in to the LMT, clickMaintenance (1), and then double-clickUser InformationMonitoring (2). In the displayed dialog box, enterMAC (3) for the terminal to be traced,select 1s (4) under the Period dropdown list box, and then click the button in the red rectangle
(5) to select the directory for saving the monitoring data.
Figure 1.1 User Information Monitoring dialog box
Step 2 As shown in Figure 1.1, we can click the List tab or the Chart tab to view the result of userinformation monitoring. The cycle is set to once per 1 second. The monitoring information
covers ten items of data such as the total number of uplink and downlink service packets,transmit power, CINR, RSSI, MCS, and threshold of outer loop power control. We can select
Show Line to control the information to be displayed.
The following figure shows the measurement information displayed in a list:
2013-06-21 HUAWEI Confidential Page 28, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
29/98
INTERNAL
Figure 1.1 Interface of the user information displayed in a list
The following figure shows the measurement information displayed in a chart:
Figure 1.2 Interface of the user information displayed in a chart
2013-06-21 HUAWEI Confidential Page 29, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
30/98
INTERNAL
2.8 Carrier Tracing
Carrier tracing is used to query the running status of each carrier, which can be displayed in alist or a chart. The following table lists the task types that can be monitored currently:
Task ID Task Type
11 Slot number occupied by uplink common channel
12 Slot number occupied by downlink broadcast channel
13 Slot number occupied by uplink basic channel
14 Slot number occupied by downlink basic channel
15 Slot number occupied by uplink primary channel
16 Slot number occupied by downlink primary channel
17 Slot number occupied by uplink traffic channel
18 Slot number occupied by downlink traffic channel
19 Uplink unicast throughput (kbit)
110 Downlink unicast throughput (kbit)
111 Downlink master IDU baseband data region power (dBm)
112 Downlink diversity IDU baseband data region power (dBm)
113 Master downlink set-top interface output power (dBm)
114 Diversity downlink set-top interface output power (dBm)
115 Transmit master standing-wave ratio
116 Transmit diversity standing-wave ratio
117 Master received signal strength (dBm)
118 Diversity received signal strength (dBm)
The procedure is as follows:
Step 1 ClickMaintenance (1), and then select Carrier Frequency Monitoring (2). The CarrierFrequency Monitoring dialog box is displayed. EnterBS ID (3), set Monitor period(s) (1s
by default) (4), and then click the button in the red rectangle (5) to specify the directory for
saving the record data files, as shown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 30, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
31/98
INTERNAL
Figure 1.1 Carrier Frequency Monitoring dialog box
Step 2 As shown in Figure 1.1, we can click the List tab or the Chart tab to view the result of userinformation monitoring. The cycle is set to once per 1 second. The monitoring information
covers eighteen items of data such as the slot number of uplink and downlink commonchannels, uplink and downlink unicast throughput, main and diversity transmit power, and
main and diversity received signal strength. We can select Show Line to control the
information to display.
The following figure shows the measurement information displayed in a table:
2013-06-21 HUAWEI Confidential Page 31, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
32/98
INTERNAL
Figure 1.1 Interface of the carrier information displayed in a list
The following figure shows the measurement information displayed in a chart:
Figure 1.2 Interface of the carrier information displayed in a chart
2013-06-21 HUAWEI Confidential Page 32, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
33/98
INTERNAL
3 Operation and Maintenance ofthe WASN9770 of the LMT
3.1 Overview of the WASN9700 LMTWASN9770 LMT is a tool used for operation and maintenance of the WiMAX gateway
WASN9770. The network planning and maintenance engineers need to modify parameters
and trace signaling by using the LMT. The WASN9770 LMT can be connected either to theR6 interface or to the local gateway maintenance port.
Precautions:
1. We need to choose a language for installing the software, for example, English or
Chinese. Ensure that the software version is consistent with the WASN gateway version.2. The serial number of the version should be WASN9770.
3. The installation type should be typical installation.
3.2 Installing and Starting the WASN9770 LMT
The installation of the WASN9770 LMT is almost same as the DBS3900 LMT. For details,
see section 2.2Installing and Starting the DBS3900 LMT.
Step 1 After installing WASN9770 LMT, click the button in the red rectangle to start the LMT, as
shown in Figure 1.1. When the WASN9770 LMT and the DBS3900 LMT are installed on onePC, they share one shortcut.
2013-06-21 HUAWEI Confidential Page 33, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
34/98
INTERNAL
Figure 1.1 User Login dialog box
Step 2 As shown in the Figure 1.1, enterOffice (generally the gateway name), IP Address, and NEType (WASN9770).ClickOK, and then clickClose.
2013-06-21 HUAWEI Confidential Page 34, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
35/98
INTERNAL
Figure 1.1 Related interfaces for entering the NE information
Step 3 As shown in Figure 1.1, enterPassword (admin by default), and then clickLogin. In thedisplayed Select Version dialog box, select the version corresponding to the gateway, and
then clickOKto log in to the WASN9700 LMT.
2013-06-21 HUAWEI Confidential Page 35, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
36/98
INTERNAL
Figure 1.1 User Login and Select Version dialog boxes
3.3 R3 and R6 Signaling Monitoring Throughthe WASN9770 LMT
To confirm the problems of network access, access failure, and handoff of NEs such asterminals, the BS, gateway, and AAA,RF engineers need to query the R3 signaling and R6
signaling at the gateway side. To perform the R3 and R6 signal tracing, pls do it as follows:
Step 1 After logging in to the LMT, clickMaintenance, and then double-clickMS Tracing (1). Inthe displayed dialog box, enterMS ID (2), select Select All (3), and then click the button inthe red rectangle (4) to select the directory for saving the signaling files automatically. By
default, Auto save to File is selected. ClickOK.
2013-06-21 HUAWEI Confidential Page 36, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
37/98
INTERNAL
Figure 1.1 MS Tracing dialog box
Step 2 After logging in to the interface of MS tracing, the real-time tracing can be performed whenthere is R3 and R6 signaling interaction between the gateway and the AAA, as shown in
Figure 1.1. Double-click one entry, and then we can view the detailed information about the
signaling.
2013-06-21 HUAWEI Confidential Page 37, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
38/98
INTERNAL
Figure 1.1 Interface of real-time R3 and R6 signal tracing
For details about how to save R3 and R6 signaling files, see Step 2 in section 2.4.
For details about how to view R3 and R6 signaling files offline, see Step 2 in section 2.5.
3.4 Running WASN9770 MML Commands
The network planning and optimization engineer need to query data, record data, and modifyparameters of the BTS by using the WASN LMT, so learning how to run MML commands is
required. To run a MML command, do it as follows:
Step 1 After logging in to the LMT, click the MML Command tab at the lower left, and then enter
the command in Command Input. Click or press the Enter button. Then, the interface
for entering commands is displayed. The items in red font are mandatory, and the items in
black are optional. When enter related information, the corresponding command is displayed
in the text box. Click or press F9 to run the command.
2013-06-21 HUAWEI Confidential Page 38, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
39/98
INTERNAL
Figure 1.1 Interface of running WASN9770 MML commands
Step 2 In the displayed Common Maintenance interface, we can query whether the command runssuccessfully.
2013-06-21 HUAWEI Confidential Page 39, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
40/98
INTERNAL
Figure 1.1 Common Maintenance interface
The operations of querying and saving history records and operations on the Help Information interfacefor the WASN9770 MML commands are the same as the DBS3900 MML commands. For details, see Step 4 and Step 5 in section 2.6.
2013-06-21 HUAWEI Confidential Page 40, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
41/98
INTERNAL
4Operation Management of the
M2000
4.1 Overview of the M2000iManager M2000 is a uniform management platform for Huawei mobile networks. Currently,
WiMAX2000 controls only the DBS3900, having the functions of batch processing of
deployment data, batch processing of parameter modification, hardware and radio parameter
importing and exporting, alarm querying, and traffic measurement customizing and obtaining.
4.2 Staring the M2000 Client
The network planning engineer use the M2000 to:
1. Obtain traffic data;
2. Query alarm;
3. Modify BTS parameters by running MML commands.
Double-click the icon of the M2000 to log in to the M2000. We need to enter the user nameand password. Generally, the user name and password are managed and assigned by themanagement engineer for the O&M center.
To start the M2000 client, pls do it as follows:
Step 2 EnterUser Name and Password, and then click the button in the red rectangle, as shown inFigure 1.1.
2013-06-21 HUAWEI Confidential Page 41, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
42/98
INTERNAL
Figure 1.1 Login dialog box
Step 3 In the displayed Server List dialog box, clickAdd orModify. Then, in the displayed dialogbox, enterName, Host Name (or IP Address), Port, and Mode, and then clickOK.
2013-06-21 HUAWEI Confidential Page 42, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
43/98
INTERNAL
Figure 1.1 Modify Server Information dialog box
Step 4 ClickLogin to log in to the M2000 client.
2013-06-21 HUAWEI Confidential Page 43, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
44/98
INTERNAL
Figure 1.1 Login progress bar
Step 5 On the menu bar, choose Topology > Main Topology. On the topology view, we can double-click or right-click an NE to view the related information in the displayed menu.
2013-06-21 HUAWEI Confidential Page 44, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
45/98
INTERNAL
Figure 1.1 Menu of Topology
Figure 1.2 Main Topology interface
2013-06-21 HUAWEI Confidential Page 45, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
46/98
INTERNAL
4.3 Operations of Traffic Measurement Data onthe M2000 Client
4.3.1 Creating the Traffic Measurement TaskCurrently, the DBS3900 can measure eight performance specifications, which are networkaccess, network withdrawal, handoff, throughput, carrier load, link quality, sleep mode, and
idle mode. We can use the M2000 to customize the measurement of these performance
specifications and create the traffic measurement task. To create the traffic measurement taskon the M2000 client, pls do it as follows:
Step 1 Choose Performance > Measure Management > Measure Settings, as shown in thefollowing figure.
Step 2 Click the Measure Management tab, and then select BWA (standing for the DBS3900) so
that we can select specific specifications and carriers to be traced.
2013-06-21 HUAWEI Confidential Page 46, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
47/98
INTERNAL
Figure 1.1 Measurement Settings
Step 3 ClickApply. Then, a dialog box is displayed, prompting we that the setting is successful.
Figure 1.1 Information dialog box
2013-06-21 HUAWEI Confidential Page 47, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
48/98
INTERNAL
Step 4 Click the Measure Status tab, and then we can view the status of all measurementspecifications. For the items that are being measured, the status indicators are green, and thestatus is Active. We can infer that the traffic measurement task is created, and the BTS
uploads the set the measurement results to the M2000 per 30 seconds.
Figure 1.1 Measurement Status
Before obtaining traffic measurement data, we need to create the traffic measurement task. We areadvised to create the traffic measurement task after the M2000 server is configured.
4.3.2 Obtaining Traffic Measurement Data
After the measurement task is created, the M2000 saves all performance specifications
reported during BTS carrier monitoring. To obtain the traffic measurement data within 30
days, do it as follows:
Step 1 Choose Performance > Query Result, as shown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 48, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
49/98
INTERNAL
Figure 1.1 Selecting Query Result
Step 2 ClickNew Query (setting new query conditions) orCondition (modifying query conditionsbased on the history query condition) to set query conditions.
Figure 1.1 Query Result interface
Step 3 Click the Object Settings tab, select Object Type, and then select SectorCarrier under theBWA directory. All the available sector carriers are displayed in Available Objects. Select the
sector carriers to be queried, and then click to add them in Selected Objects.
2013-06-21 HUAWEI Confidential Page 49, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
50/98
INTERNAL
Figure 1.1 Object Settings interface
Step 4 Click the Counter Settings tab, select Object Type, and then select SectorCarrier under the
BWA directory. All the available counters are displayed in Available Objects. Select the
items to be queried, and then click to add them in Selected Counters.
2013-06-21 HUAWEI Confidential Page 50, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
51/98
INTERNAL
Figure 1.1 Counter Settings interface
Step 5 Click the Other Settings tab, select Object Type, and then select SectorCarrier under theBWA directory. Select Continuous Time of Time Mode on the right, select Specific ofDataRange, and enterStart Time and End Time. The object, counter, and other settings are
complete. ClickQuery.
2013-06-21 HUAWEI Confidential Page 51, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
52/98
INTERNAL
Figure 1.1 Other Settings interface
Step 6 The measurement report is displayed in a table, line chart, or bar chart.
2013-06-21 HUAWEI Confidential Page 52, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
53/98
INTERNAL
Figure 1.1 Measurement report displayed in a table
Figure 1.2 Measurement report displayed in a line chart
2013-06-21 HUAWEI Confidential Page 53, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
54/98
INTERNAL
Figure 1.3 Measurement report displayed in a bar chart
Step 7 ClickSave and select the directory for saving reports. Then, the measurement reports aresaved in .xls format.
Figure 1.1 Saving measurement reports
2013-06-21 HUAWEI Confidential Page 54, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
55/98
INTERNAL
4.4 Alarm Querying Through the M2000
Alarm querying is used to display operation faults of each NE. Based on the relatedinformation, we can locate the time, source, and location information to remove faults. We
can query the alarm information either about all NEs or about a single NE by severity. Theprocedure is as follows:
4.4.1 Querying Alarms by Severity
Step 1 After logging in to the M2000, the Alarm Board dialog box is displayed. The alarmseverities are Critical, Major, Minor, and Warning, as shown in Figure 1.1.
Figure 1.1 Alarm Board
Step 2 Click each alarm severity, and the information about all NEs on the alarm severity. If we clickCritical, the information is displayed as follows:
2013-06-21 HUAWEI Confidential Page 55, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
56/98
INTERNAL
Figure 1.1 Current Fault Alarms [All objects] dialog box
Step 3 Click an entry, and the related information is displayed on the lower part of the interface, asshown in Figure 1.1.
Figure 1.1 Alarm Detail Information and Process Advice interfaces
2013-06-21 HUAWEI Confidential Page 56, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
57/98
INTERNAL
Step 4 Double-click an entry. The Detail Information dialog box is displayed, showing the detailedinformation about the alarm. We can enterAlarm Experience and Alarm Memo, and thenclickAdd orModify.
Figure 1.1 Detail Information dialog box
4.4.2 Querying Alarms by NEs
Step 1 On the main menu, choose Topology > Main Topology.
2013-06-21 HUAWEI Confidential Page 57, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
58/98
INTERNAL
Figure 1.1 Menu of Topology
Step 2 On the navigation tree of the displayed dialog box, select an NE to be queried. If the icon ofan NE is blue, we can infer that there is no alarm information about the NE. If the icon of an
NE is red, there is alarm information about the NE.
Figure 1.1 Alarm information about NEs
2013-06-21 HUAWEI Confidential Page 58, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
59/98
INTERNAL
Step 3 Right-click on the map or right-click an NE. A menu is displayed, as shown in Figure 1.1.
Figure 1.1 Querying alarm information about NEs
Step 4 We can select Current Fault Alarm, Event Alarm, History Fault Alarm, Masked FaultAlarms, orMasked Event Alarms from the shortcut menuto query related alarm
information. If we select Current Fault Alarm, the information is displayed as follows:
2013-06-21 HUAWEI Confidential Page 59, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
60/98
INTERNAL
Figure 1.1 Current Fault Alarms Object [bsc41] dialog box
Step 5 When there is no information displayed in the Clearance column, we can infer that the alarm
is not cleared. For a cleared alarm, an icon is displayed in the Clearance column, as shown inFigure 1.1.
2013-06-21 HUAWEI Confidential Page 60, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
61/98
INTERNAL
Figure 1.1 Status of alarm information
4.5 Running M2000 MML CommandsAll LMT MML commands are integrated into the M2000 to facilitate centralized management
of parameter modifications for the network planning engineer. The procedure is as follows:
Step 1 ClickMaintenance on the menu, and then clickMML or click on the navigation tree, asshown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 61, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
62/98
INTERNAL
Figure 1.1 MML Command interface
Step 2 Select an NE or multiple NEs.
Figure 1.1 Selecting NE(s)
2013-06-21 HUAWEI Confidential Page 62, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
63/98
INTERNAL
Step 3 Entering MML commands:
We can click a command to run in the left red rectangle, shown in Figure 1.1. The M2000
classified all MML commands for querying easily. Alternatively, we can enter a command to
run in the Command. Different from the LMT, the type-head function is not enabled in
M2000, so using the LMT to enter command is not convenient.
Figure 1.1 Entering MML commands
Step 4 After enter a command, click or press the Enter button to enter related parameters, asshown in Figure 1.1. The items in red font are mandatory, and the items in black are optional.
2013-06-21 HUAWEI Confidential Page 63, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
64/98
INTERNAL
Figure 1.1 Entering MML commands
Step 5 Running MML commands:
After entering a MML command and related parameters, click or press F9 to run the
command. In the Common Maintenance interface, we can view the object, NE, operationtime, and running result.
2013-06-21 HUAWEI Confidential Page 64, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
65/98
INTERNAL
Figure 1.1 Running MML commands
In the History Command interface, we can query the history operation records, as shown in
Figure 1.2.
Figure 1.2 History Command interface
2013-06-21 HUAWEI Confidential Page 65, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
66/98
INTERNAL
In the Help Info interface, we can query the meaning of the current command, the meaning ofeach related parameter, and corresponding value range.
Figure 1.3 Help Info interface
2013-06-21 HUAWEI Confidential Page 66, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
67/98
INTERNAL
History operations can be exported in .txt format. To export history operations, right-click theentry, and then select Export All from the shortcut menu, as shown in Figure 1.4.The
information that can be exported includes the command, NE, operation time, and operation
result.
Figure 1.4 Exporting history operations
2013-06-21 HUAWEI Confidential Page 67, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
68/98
INTERNAL
5 Operations of the WCS5.1 Overview of the WCS
The WiMAX Configuration Solution (WCS) is a graphic batch tool integrated into the M2000
client. It provides a convenient operation platform for network planning engineers. The
common operations are as follows:
1. BTS parameter batch processing
2. Neighbor cell adding
3. Radio parameter script importing and exporting
5.2 BTS Parameter Batch ProcessingBTS parameter batch processing is to send all configured parameters for modification at one
time to multiple BTSs to perform modification by using the WCS. The procedure is as
follows:
Step 1 Create a new project (similar to modifying a project, not referred in this document).
After starting the M2000, clickConfiguration from the menu, and then select WiMAX
Enhanced Configuration, as shown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 68, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
69/98
INTERNAL
Figure 1.1 Main menu of the M2000
ClickProject, and then select New Project. In the displayed New Project dialog box, enterName and Description, and then clickOK.
Figure 1.2New Project dialog box
Step 2 Selecting the NEs for operation:
2013-06-21 HUAWEI Confidential Page 69, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
70/98
INTERNAL
On the navigation tree, select the NEs for operation, and then click the Radio Network Datatab, as show in Figure 1.1.The WCS classified all BTS parameters into hardware data,
transport network data, radio network data, and neighbor data. Generally, network planning
engineers modify only radio network data and neighbor data.
Figure 1.1 Selecting NEs
Step 3 Selecting a parameter from the parameter list:
2013-06-21 HUAWEI Confidential Page 70, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
71/98
INTERNAL
After selecting the NE, we can select the parameters to modify from the list. If we select
CARRIERBASICINFO from Radio Network Data, do it as Figure 1.1 shows.
Figure 1.1 Selecting a parameter
Step 4 Modifying a parameter:
2013-06-21 HUAWEI Confidential Page 71, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
72/98
INTERNAL
Select a parameter to modify, as shown in Figure 1.1. Click the parameter row. The modifiedvalue is displayed in red font and marked with "modify" for identification.
Figure 1.1 Modifying parameters
Step 5 Saving project files:
2013-06-21 HUAWEI Confidential Page 72, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
73/98
INTERNAL
Click to save the modified parameters, as shown in Figure 1.1.
Figure 1.1 Saving modified parameters
Step 6 Checking validity of parameters:
2013-06-21 HUAWEI Confidential Page 73, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
74/98
INTERNAL
After saving project files, we need to check validity of parameters. Click . The
Check Apply Report dialog box is displayed. Select the NEs and parameters to be checked.ClickCheckto perform the validity check.
Note: We need to save the project, and then check the validity of parameters. Otherwise, wecannot perform the validity check of parameters.
Figure 1.1 Checking validity of modified parameters
Step 7 Applying parameters:
2013-06-21 HUAWEI Confidential Page 74, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
75/98
INTERNAL
If the validity check is successful, the parameters can be applied. Otherwise, go back to the
steps for modifying parameters. Click , and then the modified parameters can be
applied, as shown in Figure 1.1.
Figure 1.1 Applying modified parameters
Step 8 Synchronizing NEs:
2013-06-21 HUAWEI Confidential Page 75, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
76/98
INTERNAL
After applying the parameters, we need to synchronize the NEs to refresh the status of the
NEs displayed on the M2000.Click , and then select the NEs to besynchronized. ClickOK.
Figure 1.1 Synchronizing NEs
After we perform the previous eight steps, the BTS parameter batch processing is complete.
5.3 Neighbor Cell Adding
With this function, we can configure neighbor cells for a single BTS by entering nocommand. The procedure is as follows:
Step 1 On the main menu, choose Configuration > WiMAX Enhanced Configuration. Then createa new project. For details, see the related content in section 4.1.
2013-06-21 HUAWEI Confidential Page 76, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
77/98
INTERNAL
Figure 1.1 Main menu of the M2000
Step 2 In the displayed WiMAX Enhanced Configuration interface, select NEs on the navigationtree, and then click the Neighbor Data tab. Information about all central BSs is displayed in
Center Carrier Information. Information about all neighbor cells of the selected BSs isdisplayed in Destination Carrier, as shown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 77, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
78/98
INTERNAL
Figure 1.1Neighbor relations
Step 3 In Destination Carrier, right-click an entry, and then select Add Neighbor Carrier from theshortcut menu. A dialog box is displayed, as shown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 78, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
79/98
INTERNAL
Figure 1.1 Add Neighbor Carrier interface
Step 4 The File Type dropdown list box has three options: By Site Name, By Distance, and By SiteID. If we select By Site Name and clickFind, all BTSs are displayed by site name, as shown
in the following figure. Determine the neighbor cells to be added, click the button in the redrectangle to add them to the table on the right, and then clickOK, as shown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 79, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
80/98
INTERNAL
Figure 1.1 Add Neighbor Carrier interface
Step 5 Click the Checktab. A dialog box is displayed, as show in the following figure. Select an NEon the left. Then, the neighbor cells checking are displayed, as shown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 80, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
81/98
INTERNAL
Figure 1.1 Check Consistent Report interface
Step 6 After selecting the NE, clickCheckin the displayed dialog box. We can view the checkprogress, as shown in the following figure.
2013-06-21 HUAWEI Confidential Page 81, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
82/98
INTERNAL
Figure 1.1 Check Consistent Report interface
Step 7 When the check is completed, pls clickApply. We can view the progress, as shown in thefollowing figure.
2013-06-21 HUAWEI Confidential Page 82, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
83/98
INTERNAL
Figure 1.1 Apply interface
Step 8 When the applying operation is completed, the information about the added neighbor celldisplay, as shown in the following figure.
2013-06-21 HUAWEI Confidential Page 83, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
84/98
INTERNAL
Figure 1.1 Apply complete interface
Step 9 Then, click the Synchronize tab. A dialog box displays, as shown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 84, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
85/98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
86/98
INTERNAL
Figure 1.1 Synchronizing NEs
Then, the BTS neighbor cell is successfully added.
5.4 Radio Parameter Importing and ExportingDuring BTS deployment, RF engineers need to export configuration scripts of radio network
parameters and neighbor parameters. During BTS maintenance, RF engineers need to checkBTS configurations. The WCS provides the function of importing and exporting radioparameter scripts.
5.4.1 Importing BTS Radio Parameters
Step 1 After entering the main interface, click the Import tab. In the displayed dialog box, selectWireless Parameter of the Select file type dropdown list box, as shown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 86, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
87/98
INTERNAL
Figure 1.1 Importing radio parameters
Step 2 Click to select the directory for importing configuration scripts that are completed in.xls format by network planning engineers, and then clickOpen.
2013-06-21 HUAWEI Confidential Page 87, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
88/98
INTERNAL
Figure 1.1 Selecting the directory for importing radio parameters
Step 3 After the script files are opened, the WCS performs the parameter check. We can view theprogress, as shown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 88, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
89/98
INTERNAL
Figure 1.1 Checking the radio parameters to be imported
Step 4 When the parameter check is complete, the corresponding BTSs display. We can either selectSelect to import for a single BTS or select select all for all BTSs. ClickImport, and theWCS configures the selected BTS(s).
2013-06-21 HUAWEI Confidential Page 89, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
90/98
INTERNAL
Figure 1.1 Importing radio parameter scripts
Step 5 When all scripts are imported, a message box is displayed to prompt that all scripts aresuccessfully imported.
2013-06-21 HUAWEI Confidential Page 90, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
91/98
INTERNAL
Figure 1.1 Importing radio parameter scripts
Step 6 Then, click the Synchronize tab. A dialog box is displayed, as shown Figure 1.1.
2013-06-21 HUAWEI Confidential Page 91, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
92/98
INTERNAL
Figure 1.1 Synchronizing NEs
Step 7 Select the NE to be synchronized. When the synchronization is complete, the interface isdisplayed as follows:
2013-06-21 HUAWEI Confidential Page 92, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
93/98
INTERNAL
Figure 1.1 Synchronizing NEs complete
5.4.2 Exporting BTS Radio Parameters
Step 1 After entering the main interface, click the Export tab. In the displayed dialog box, select anNE to be exported and select Wireless Parameter of the File Type dropdown list box, as
shown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 93, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
94/98
INTERNAL
Figure 1.1 Exporting radio parameters
Step 2 Click to select the directory for saving the scripts. Modify the file name as required,and then clickSave.
2013-06-21 HUAWEI Confidential Page 94, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
95/98
INTERNAL
Figure 1.1 Selecting the directory for exporting radio parameters
Step 3 We can view the progress, as shown in Figure 1.1.
2013-06-21 HUAWEI Confidential Page 95, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
96/98
INTERNAL
Figure 1.1 Progress of exporting radio parameters
Step 4 When all scripts are exported, a message box is displayed to prompt that all scripts aresuccessfully exported.
2013-06-21 HUAWEI Confidential Page 96, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
97/98
INTERNAL
Figure 1.1 Exporting radio parameters complete
Step 5 Select the directory for exporting the script files, and then we can view all exportedconfiguration scripts.
2013-06-21 HUAWEI Confidential Page 97, Total 98
-
7/28/2019 WiMAX OMC Operation Guide 20090216 a 1.0
98/98
INTERNAL
6 Summary1. Due to lack of real NE environment, guide to some operations of the AAA will be
complete in the next version.
2. Due to lack of real NE environment, guide to some operations of the Nastar will be
complete in the next version.
3. Specific guide to the GW traffic measurement collection will be complete in the nextversion.