Wi-Fi Configuration

Option I /via Laptop/Pad

• Preparation

1. Power Wi-Fi inverter (or Ezlogger WiFi) on.

2. If you are configuring Wi-Fi inverter, make sure the yellow led on front cover is blinking. Otherwise please set the protocol to

\Ni-Fi according to user manual of inverter at first.

3. Power Wi-Fi router on.

4. Switch on t he Wi-Fi of laptop.

• Configure Wireless Network

1. Connect Wi-Fi to'Solar-WiFi '(Password:'12345678'),

Browse website: http:f/10.10.100.253 . . ~~

•FJ L§':!Z0:.·:.' 0:c.l:.:.OO:c.2:.:.S3:_ ___ =:Q] ('-'(("--____ )

3. Click 'Start Setup'

Device information

Firmware verison

MAC address

Wireless AP mode

SSID

IP address

Wireless STA mode

Router SSID

Encryption method

Encryption algorithm

1.6.9.3.38.2.1.38

60:C5:A8:60:33:E1

Enab le

Solar-WiFi

10.10.100.253

Disable

WiFi Bum-in

WAP/WAP2-PSK

AES

Router Password WiFi Bum--in

Can not join the network , m ay b e caused by :

router doesn't exist , or signal is too week, or password is incorrect

* Hel p:Wizard will help you to complete setting within one mimute. -~ • Th!i! W1-F1 module parameters pfease refer to ' ~ 1

~. ,.! • ·. :oevt~e mformatio.n1 eotutnn above .

-

2. Enter User name:' admin' . Password:' admin'

f - l Admin(!.!) : ~min _______j

~=====-------======~ Password:

[Y'] Remember the password(R)

4. Select Wi-Fi router's SSID and click 'Next '

0 1

Please select your current wireless Mtwork:

SSID Sec mode Enc type Channel RSSI

@ WIFI Test WAP2-PSK AES 54%

* Note: When RSSI of the selected WiFi Network is lower than 10%, the

connection may be unstable, please select other available network or

shorten the d istance between the device and the router.

tf your wireless router does not broadcast SSID, please c lick "Next" and

add a wireless network manually. --

5. Fill in password and click 'Next '

Add wireless netwo rk manually

Network name {SSID) !WiF i-Test

Encryption method !WPA/WPA2-PSK · I Encryption algorithm · I

Please enter the wireless network pass w ord:

Password (8-63 bytes) "ln-ce l'""lo-go- o-cd-we----,

0 sllow psk

* Note: case sensitive for SSID and password

Please make sure all parameters of w ireless network are matched with router,

inc luding password .. _ p PU~a:;e m;~ s~r~ all paramet~ of ~;reless netw~'rk ' :

'!. ~ are ~atched with the rdtft;~ ~1~?~~ng pas~~or~ ~ ·, f ~

• Friendly Tips

Wizard Access point setting

Advanced Network name (SS10) §iFi-Test

6. 6. Cl ick'Complete' and the configuration process

completes.

Save success!

Click 'Complete', the current configuration w ill take effect after

restart

If you still need to configure the other pages of information, please

go to complete your required configuration.

Configuration is completed, you can log on the Management page

to restart device by Click on 'OK' button.

Confirm to complete?

Management Encryption mode jWPA{WPA2- PSK · I You can modify the Wi-Fi modu le's SSID or/and password in the 'Advanced' interface.

Encryption algorithm frKtP/AES · I Password{S to 63 characters) ~ SKIP THIS STEP UNLESS IT IS NECESSARY!

* Note: config the device's parameter under the access point mode.

DHCP setting for STA

IPDHCP Mode

IP address

Subnet address

Gateway address

ONS server address

-·I

* Note: After changing the settings, the device must be restarted. -Notice: The AP 'So/ar-WiFi' will disappear after inverter connects to WiFi router. Turn off router or do 'WiFi Reload' operation via button on inverter if you need connect to inverter once again.

Go to portal, register and create your PV station. You can find out the website of portal in user manual.

02 340-00072-02