WHEEL LOADERS INTEGRATED TOOL CARRIERS · The standard tools offered by Caterpillar can be used on...
Transcript of WHEEL LOADERS INTEGRATED TOOL CARRIERS · The standard tools offered by Caterpillar can be used on...
© 2014 Caterpillar. All Rights Reserved. CAT, CATERPILLAR, BUILT FOR IT, their respective logos, “Caterpillar Yellow,” the “Power Edge” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
800.437.4228www.hawthornecat.com
Caterpillar® Performance
Handbook Edition 44
WHEEL LOADERS
INTEGRATED TOOL CARRIERS
PART B
23-228 Edition 44
Wheel LoadersIntegrated Toolcarriers
Machine/Attachment Selection
MACHINE/ATTACHMENT SELECTIONThe Integrated Toolcarrier’s versatility and the wide
range of attachments makes the “single machine fleet” concept highly attractive to an increasing number of users.
A Job Analysis helps identify applications, work require ments, material handling parameters and the cur rent working method. Thoroughly research each ele ment in the following chart, the gathered infor ma-tion will help select the proper Integrated Tool carrier System.
Work Processes:The first step in the job analysis is to identify all work
processes from start to finish. Key questions outlined below will begin to indicate the required attachments and potential Integrated Toolcarrier applications.
● What kinds of work are performed: (e.g., dozing, loading, stacking, digging, sweeping, handling special materials, etc.)
... in site preparation?
... below ground level?
... at ground level?
... above ground level?
... in landscaping?
... in maintenance equipment yard?etc.
● What work is done manually that could be done with an Integrated Toolcarrier?
● What are the work conditions?: ... underfoot?
... grades?
... tight quarters?
... time restraints?
... climate?etc.
Materials Handled:Examining the materials handled will assist in deter-
mining necessary attachments. Sizes and weights of mate rial(s) handled will indicate the appropriate Inte-grated Toolcarrier model by defining lift and reach require ments. Concentrate on the material flow at the job site — the point of origin as well as the final desti-na tion for the various materials will undoubtedly have material handling requirements.● What kinds of materials are handled (e.g. snow, earth,
bricks, chemicals, pipe, logs, etc.)● What form are the materials handled in: bulk?
palletized?● How much does each weigh?● What are the dimensions of each?● What are the... movement
parameters: ... dozed what distance?... load and carried what
distance?... lifted how high?... placed below ground
level?... placed what distance
from machine?
JOB ANALYSIS METHOD
● APPROPRIATE INTEGRATED TOOLCARRIER MODEL SIZE
● NECESSARY ATTACHMENTS
UTILIZATION & SEQUENCE?
CURRENT EQUIPMENT?
MATERIALS HANDLED?
PRINCIPAL WORK
WORK PROCESSES?
PHB-Sec23(pg175-290).indd 228PHB-Sec23(pg175-290).indd 228 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-229
Machine/Attachment Selection Wheel LoadersIntegrated Toolcarriers
Current Equipment:If determining material weight is not possible, much
information can be determined from looking at the current equipment fleet. This will suggest required per-for mance capabilities such as lifting capacity.● Machines currently doing the work (e.g. wheel load-
ers, lift trucks, sweepers, light capacity cranes, snow plows, etc.)?
● What special (maximum) capabilities does each machine have (production, lift height, load capacity, width/height dimensions, reach, turning radius, travel speed, etc.)?
● To what extent are each machine’s maximum capa-bilities used?
● What are owning/operating costs of each?
Utilization & Sequence:Utilization implies how often the current machines
are used and what will be the utilization factors for the Integrated Toolcarrier with each individual attach ment. Sequence implies what order these tasks are accom plished in and if two or more machines operate at the same time. This portion of the job analysis should assist in com-par ing economies of various systems. Other important con sid erations may be the number of operators needed, storage space, reduced maintenance requirements, etc.● How often (what percent) is each machine used?● How often and when does it sit idle?● How often and when do two or more machines work
at the same time?● Can the operation be changed to permit single machine
operation?
Principal Work:Utilization and sequence will indicate the principal
work the Integrated Toolcarrier will do, further assist-ing in attachment and model sizing and selection. The basic machine/tool package should be able to handle the toughest, most frequently performed jobs for the primary application. Secondary tools can have a little more “give and take” in their performance capabilities than the primary tool.● What work can be accomplished by an Integrated
Toolcarrier?● What work will take up the majority of Integrated
Tool carrier time?● What work will use the maximum static tipping capa-
bilities of the Integrated Toolcarrier?● What high cost (owning and operating) and/or low
utilization machines can be replaced by an Inte grated Toolcarrier?
Additional Tips for Tool Sizing and SelectionTool selection will principally concern hydraulic power
requirements and static tipping load considerations. The standard tools offered by Caterpillar can be used on any Integrated Toolcarrier machine with little difficulty. However, tools such as the hydraulic broom, claws, blades and asphalt cutter will require additional consideration before proposing a system to the customer.
Fork Rating
Table indicates rated pallet fork load at standard ma chine configuration, 600 mm (24") load center, 1200 mm (3'11") fork on IT14G2-930H, see operator man-ual to determine rated load for vehicle configuration being used.Model kg lb Model kg lbIT14G2 1870 4123 930K High Lift 2476 5459924K Standard 2864 6313 938K Standard 3765 8297924K High Lift 2284 5035 938K High Lift 2941 6483930K Standard 3251 7165
PHB-Sec23(pg175-290).indd 229PHB-Sec23(pg175-290).indd 229 12/20/13 9:07 AM12/20/13 9:07 AM
23-230 Edition 44
Wheel LoadersIntegrated Toolcarriers
Machine/Attachment Selection
Bucket Rating
Bucket capacity, SAE J742 FEB85 (nominally heaped)Table indicates rated load at vehicle configuration
noted by the asterisks. See operator manual to deter-mine rated load for vehicle configuration being used.
1.4 m3 (1.75 yd3) with Bolt-on Cutting EdgeIT14G2* 2273 kg 5000 lb
1.3 m3 (1.7 yd3) with Bolt-on Cutting Edge910K 2145 kg 4730 lb
1.5 m3 (2.0 yd3) with Bolt-on Cutting Edge914K 2390 kg 5269 lb
1.9 m3 (2.5 yd3) with Bolt-on Cutting Edge924K*** Standard 3710 kg 8179 lb924K*** High Lift 2946 kg 6494 lb
2.1 m3 (2.7 yd3) with Bolt-on Cutting Edge924K*** Standard 3671 kg 8093 lb924K*** High Lift 2725 kg 6008 lb
2.1 m3 (2.7 yd3) with Bolt-on Cutting Edge930K**** Standard 4185 kg 9226 lb930K**** High Lift 2959 kg 6523 lb
2.3 m3 (3.0 yd3) with Bolt-on Cutting Edge930K**** Standard 4146 kg 9140 lb930K**** High Lift 2920 kg 6437 lb
2.5 m3 (3.3 yd3) with Bolt-on Cutting Edge938K**** Standard 4764 kg 10,503 lb938K**** High Lift 3451 kg 7608 lb
2.7 m3 (3.5 yd3) with Bolt-on Cutting Edge938K**** Standard 4719 kg 10,404 lb938K**** High Lift 4589 kg 10,117 lb**** Specifications shown are for high-speed version IT14G2 and include
lubri cants, full fuel tank, ROPS cab, 80 kg (176 lb) operator, standard 250 kg (550 lb) counterweight and 17.5-R25 (L-2 equivalent) tires.
**** Specifications shown include lubricants, full fuel tank, limited slip axles, heavy duty rear brakes, optional counterweights, additional guarding, ROPS cab with A/C, 80 kg (176 lb) operator and 20.5-R25 (L-3) tires.
**** Specifications shown include lubricants, full fuel tank, standard counter-weights, additional guarding, 80 kg (176 lb) operator, and 20.5 R25 (L-3) XHA2 tires.
**** Specifications shown include lubricants, full fuel tank, heavy counter-weights, additional guarding, 80 kg (176 lb) operator, and 20.5 R25 (L-3) XHA2 tires.
The charts explain each machine’s maximum pay-load. The maximum material density would be deter-mined by dividing the payload by the bucket capacity. If the actual material density exceeds the recommended material density, the process should be repeated to select the properly sized bucket.
A similar procedure would be used with the forks and material handling arm to determine maximum rec om-mended lifting capacity and/or required IT model size.
Pallet ForkThe pallet fork will fulfill many material handling
needs. A modified Class 3 fork carriage provides visi-bility to the tines for precision pallet work. This car-riage with non-standard spacing accepts many Class 3 lift truck attachments.
Pallet fork rated operating loads are based on the following:
SAE J1197 FEB91: 50% of the full turn static tip-ping load or the hydraulic/structural limitations.
CEN 474-3 (European standard): 60% of the full static tipping load on rough terrain or the hydraulic/struc tural limitations. 80% of the full turn static tipping load on firm, level ground or the structural/hydraulic limitation. Other local, regional or international guide-lines may also apply.
If operation is on rough ground these criteria may need modification. In this instance, the size and rating of existing equipment should be considered.
Sizing for pallet work generally consists of answering the following questions.1. What are the average loaded pallet dimensions?2. Lift Capacity — what capacity is required to lift and
move the average pallet load? The maximum pallet load?
3. Lift Height — can the machine reach the top level of the standard pallet stack? What are the maxi mum reach, lift and height requirements?
4. Maneuverability — can the machine work around the current aisle configuration? In the stacking aisles? Main aisles? Intersecting aisles? Are 90° turns required in any aisle for material placement?
5. Length — what tine length is required to fit the com-monly used pallets? (1219 mm [4'0"] tines are standard length for most palletized material.)
6. Any machine height restrictions?7. Any special fork configurations required?
Lift capacity, lift height, aisle configuration and tine length are the most important considerations in recom-mending a pallet handling machine.
PHB-Sec23(pg175-290).indd 230PHB-Sec23(pg175-290).indd 230 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-231
Machine/Attachment Selection Wheel LoadersIntegrated Toolcarriers
Example problem:
The following example applies the job analysis method to a work situation.
Sewer & Water ContractorSets water lines (152 mm-610 mm [6 in-24 in] iron
pipe), sanitary sewer lines (152 mm-457 mm [6 in-18 in] PVC) and storm sewer lines (610 mm-1067 mm [24 in- 42 in] concrete pipe) primarily in urban areas ... often-times across or down existing streets.
MaterialsLoam/Clay: 1600 kg/m3 (2700 lb/yd3) loose densityBedding
(Gravel): 1900 kg/m3 (3200 lb/yd3) loose densityWater Pipe: 610 mm (24 in) push-on joint ductile
iron, 6.1 m (20 ft) sections, 1309 kg (2885 lb) 215 kg/m (144.3 lb/ft) × 6.1 m (20 ft).
Storm Sewer: 1067 mm (42 in), Wall B, concrete pipe, 1.5 m (5 ft) sections, 1556 kg (3430 lb) 1021 kg/m (686 lb/ft × 5 ft).
Manhole Boxes: 1361 kg (3000 lb)WHAT INTEGRATED TOOLCARRIER MODEL SHOULD BE RECOMMENDED?WHICH ATTACHMENTS?
Work ProcessesIntegrated Toolcarrier
Attachment PossibilitiesBundled PVC and
individual concrete/iron pipe-loaded/unloaded (yardsite) and strung along trench
Forks/MaterialHandling Arm
Unload, handle, set manhole boxes
Material Handling Arm
Excess excavated material truck loaded
Bucket
Bedding material handled/placed
Bucket
Trench backfilled Bucket/BladeTrench compaction Compactor WheelRough and finish grading Bucket/BladeStreet cleanup Bucket/BroomPavement removal Rebar Snips/Asphalt
Cutter
Current Equipment UtilizationCat 225. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90%Champ CB607 lift truck,
3175 kg (7000 lb) capacity. . . . . . . . . . . . . 15%Deere 444 with 1.1 m3 (1.5 yd3)
G.P. bucket. . . . . . . . . . . . . . . . . . . . . . . . . 60%Rosco D-50 sweeper. . . . . . . . . . . . . one half hour/dayRammax 1361 kg (3000 lb) self-propelled
trench compactor. . . . . . . . . . . . . . . . . . . . 25%
Machine sizing1350 mm (53 in) Forks
Operating Load at Full Turn*Model kg lbIT14G2 1810 5991924K Standard 2781 6131924K High Lift 2224 4903930K Standard 3158 6962930K High Lift 2414 5322938K Standard 3661 8071938K High Lift 2869 6325
Water pipes:1309 kg (2885 lb)
IT14G2 ... 1 pipe — no problem924K Standard ... 1 pipe — no problem924K High Lift ... 1 pipe — no problem930K ... 1 pipe — no problem930K High Lift ... 1 pipe — no problem938K ... 1 pipe — no problem938K High Lift ... 1 pipe — no problem
Storm sewer pipes:1556 kg (3430 lb)
IT14G2 ... 1 pipe — no problem924K Standard ... 1 pipe — no problem924K High Lift ... 1 pipe — no problem930K ... 1 pipe — no problem930K High Lift ... 1 pipe — no problem938K ... 1 pipe — no problem938K High Lift ... 1 pipe — no problem
* Note that the most conservative operating load (SAE J1197 FEB91) is used here. The rated operating load for some competitive machines with pallet forks will be based upon European standard CEN 474-3, assuming operation on firm and level ground (i.e. using 80% of full turn static tipping load).
PHB-Sec23(pg175-290).indd 231PHB-Sec23(pg175-290).indd 231 12/20/13 9:07 AM12/20/13 9:07 AM
Performance Series Buckets
Performance Series Buckets utilize a system-based approach to balance bucket shape against the machine’s linkage, weight, lift and tilt capacities. The result is a bucket optimized for performance and productivity, and intended for use in production applications. Perfor-mance Series Buckets for Wheel Loaders are designed for use in truck loading, stockpiling and load-and-carry applications. Per formance is improved over current buckets in these production applications with materials such as sand, gravel and aggregates.
Loads EasyProven design characteristics improve material flow
into the bucket and improve material retention during transport. In some situations, the number of passes required to fill a truck is reduced. Performance Series Buckets are designed for optimum performance on the machine. Profile changes (over current buckets) improve load-abil ity and make Performance Series Buckets machine-specific.
Fuel EfficientPerformance Series Buckets have a longer floor — easily
digging through the pile. Less time in the pile equals less fuel consumed.
Higher Fill FactorsWhen comparing buckets of the same rated capacity,
Performance Series Buckets have higher fill factors — up to 115%.
Move More Material with the Same Rated CapacityMore material can be moved with a Performance Series
Bucket compared to a same-size rated capacity current bucket. Likewise, a smaller Performance Series Bucket can be utilized to move the same amount of material as a larger rated capacity current bucket.
Carries MoreProductive
Bucket shape and strike plane angle are designed for material retention and consistent load sizes. More mate-rial loads into the bucket and is carried all the way to the truck, hopper or stockpile.
A spill guard diverts overflow away from hinge pins, lift arms, hydraulic cylinders and tilt sensors help ing to protect these areas of the machine.
Bucket SpecificationsPerformance Series Buckets are designed to bring opti-
mum performance to a specific machine. Profile changes over current buckets allow higher fill factors and increased production.
Incompatibility on the 950H and 962HThe recent linkage change on the 950K and 962K has
created some incompatibility issues with the Fusion Per formance Series Buckets. Because the bucket shape has been optimized for the machine linkage, Fusion Per-formance Series Buckets designed for use on the 950K and 962K will experience interference with the linkage on the 950H and 962H. For this reason 950K and 962K Performance Series Buckets should NOT be used on the 950H and 962H machines.
Incompatibility on the 966H/K/MBecause 972H/K/M Performance Series Buckets are
designed specifically for performance on the 972H/K/M — their shape brings some incompatibilities with the 966H/K/M machine. These buckets can be pinned on to the 966H, but will experience interference with machine linkage in the rack back position. For this reason, 972H/K/M Performance Series Buckets should not be used on 966H/K/M machines. This is different than current General Purpose Buckets.
23-232 Edition 44
Wheel LoadersIntegrated Toolcarriers
Machine/Attachment Selection
PHB-Sec23(pg175-290).indd 232PHB-Sec23(pg175-290).indd 232 12/20/13 9:07 AM12/20/13 9:07 AM
23
Certain Bucket Sizes Require Additional Counterweight
Compared to a current bucket of the same rated capac-ity, Performance Series Buckets will move more mate-rial. To maintain appropriate machine stability, 980H machines utilizing the two larger Performance Series Buckets must be equipped with the aggregate loader counterweight. This is required for machine stability based on the bucket size/fill factor combination.
Compatible with G and G II machinesPerformance Series Buckets for 988-size machines are
compatible with standard and high lift linkages on G and G II Series machines.
Material Handling Arm (MHA)The rated load for the MHA is 50% of the full turn
static tipping load in each position or hydraulic or struc-tural limitations. Manually extendable telescopic sections enable maximum lifting capacity at the full retracted position, and maximum lift height and reach in the fully extended position.
Operating Load at Full Turn
Model Retracted Mid ExtendedIT14G2 1370 kg 1067 kg 8888 kg
3021 lb 2373 lb 1958 lb924K StandardHook On
1903 kg 1614 kg 1401 kg4148 lb 3518 lb 3055 lb
924K High LiftHook On
1608 kg 1386 kg 1218 kg3545 lb 3056 lb 2685 lb
930K StandardHook On
2158 kg 1830 kg 1589 kg5188 lb 4034 lb 3502 lb
930K High LiftHook On
1763 kg 1525 kg 1343 kg3886 lb 3361 lb 2961 lb
938K StandardHook On
2737 kg 2134 kg 1855 kg6032 lb 4702 lb 4088 lb
938K High LiftHook On
2091 kg 1808 kg 1593 kg4608 lb 3986 lb 3512 lb
Storm sewer pipes:1556 kg (3430 lb)
IT14G2 ... no924K ... yes in retracted and mid930K ... yes in retracted, mid, and extended938K ... yes in retracted, mid, and extended
Manhole boxes:1361 kg (3000 lb)
IT14G2 ... no924K ... yes in retracted and mid930K ... yes in retracted, mid, and extended938K ... yes in retracted, mid, and extended
BucketsAll general purpose buckets are interchangeable on
924K-938K due to common attachment points on the quick couplers. Bucket selection will depend on the material density in your application. Offering multiple sized buckets allows the user the flexibility to closely match material density and bucket size with machine capa bility. Equipping a machine with too large a bucket will result in unacceptable stability — too small a bucket may provide inadequate tire coverage.
Bucket 1780 kg/m3 (3000 lb/yd3) ... 100% fill factor
Edition 44 23-233
Machine/Attachment Selection Wheel LoadersIntegrated Toolcarriers
PHB-Sec23(pg175-290).indd 233PHB-Sec23(pg175-290).indd 233 12/20/13 9:07 AM12/20/13 9:07 AM
23-234 Edition 44
Wheel LoadersIntegrated Toolcarriers
Machine/Attachment Selection
Model Bucket Payload50% Full Turn Static Tipping
924K* Hook On 1.9 m3 3382 kg 3710 kg2.5 yd3 7456 lb 8179 lb2.1 m3 3738 kg 3671 kg2.7 yd3 8241 lb 8093 lb2.3 m3 4094 kg 3634 kg3.0 yd3 9026 lb 8012 lb
930K* Hook On 2.1 m3 3738 kg 4185 kg2.7 yd3 8241 lb 9226 lb2.3 m3 4094 kg 4146 kg3.0 yd3 9026 lb 9140 lb2.5 m3 4450 kg 4077 kg3.3 yd3 9811 lb 8988 lb
938K* Hook On 2.5 m3 4450 kg 4764 kg3.3 yd3 9811 lb 10,503 lb2.7 m3 4806 kg 4720 kg3.5 yd3 10,595 lb 10,406 lb2.9 m3 5162 kg 4684 kg3.8 yd3 11,380 lb 10,326 lb
NOTE: Metric numbers are a product of conversion.**924K, 930K, and 938K equipped with Michelin 20.5-R25 XHA2 tires.**924H and 930H equipped with Michelin 20.5-R25 XHA tires.
Machine/Attachment Recommendation930K — The greater static tipping load capabilities allow it to do a greater portion of the contractor’s total work processes. With the following attach ments, the 930K could replace part or all of the specialty units, such as the wheel loader, rough terrain lift truck, street sweeper, and/or the trench compactor.2.1 m3 (2.75 yd3), 2.3 m3 (3.0 yd3), or 2.5 m3 (3.25 yd3) General Purpose Bucket1350 mm (53 in) forks (handles all pipes)Material Handling Arm — (handles pipe sizes under 1067 mm (42 in) concrete and manhole boxes ... 225 would have to set 1219 mm (48 in) and larger concrete pipeBroom
Optional Attachments to Consider:24-LH compactor wheelRebar snipsAsphalt cutter
PHB-Sec23(pg175-290).indd 234PHB-Sec23(pg175-290).indd 234 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-235
Wheel LoadersIntegrated Toolcarriers
23
Buckets● Americas North
Model Interface Bucket TypeWidthRange
CapacityRange
WeightRange GET
mm in m3 yd3 kg lb924K Fusion General Purpose
Performance Series 2550 100 1.9-2.5 2.5-3.2 775-963 1705-2119 J250/BOCE
Light Material 2750 108 3.5-5.0 4.5-6.5 1161-1502 2554-3311 J250/BOCEMulti-Purpose 2550 100 2.1 2.7 1288 2834 BOCESide Dump 3105 122 1.9 2.5 1653 3644 BOCE Included
High Dump2550-3060
100-120 3.0-5.0 4.0-6.5 1688-2123 3721-4680 BOCE Included
Grapple 2697 106 2.7-2.9 3.5-3.8 1632-1673 3598-3688 J250/BOCEWaste 3059 120 3.6-3.8 4.7-5.0 1416-1474 3122-3250 BOCE IncludedWoodchip 3330 131 4.9-5.3 6.4-6.9 1717-1775 3785-3913 BOCE IncludedGrading 2700 106 1.9 2.5 1233 2716 BOCE Included
Pin On General Purpose Performance Series 2550 100 1.9-2.2 2.5-3.0 812-1057 1786-2330 J250/BOCE
Light Material 2750 108 3.1-5.0 4.0-6.5 1096-1383 2416-3043 J250/BOCE
High Dump2550-3060
100-120 3.0-5.0 4.0-6.5 1695-2149 3737-4738 BOCE Included
Sand and Gravel 2750 108 2.6-3.2 3.4-4.1 1026-1147 2262-2523Doze 2743 108 5.5 4.2 1506 3321 BOCELoad & Carry 2743 108 6.0 4.6 1528 3369 BOCE
930K Fusion General Purpose Performance Series 2550 100 1.9-2.5 2.5-3.2 775-963 1705-2119 J250/BOCE
Light Material 2750 108 3.5-5.0 4.5-6.5 1161-1502 2554-3311 J250/BOCEMulti-Purpose 2550 100 2.1 2.7 1288 2834 BOCESide Dump 3105 122 1.9 2.5 1653 3644 BOCE Included
High Dump2550-3060
100-120 3.0-5.0 4.0-6.5 1688-2123 3721-4680 BOCE Included
Grapple 2697 106 2.7-2.9 3.5-3.8 1632-1673 3598-3688 J250/BOCEWaste 3059 120 3.6-3.8 4.7-5.0 1416-1474 3122-3250 BOCE IncludedWoodchip 3330 131 4.9-5.3 6.4-6.9 1717-1775 3785-3913 BOCE IncludedGrading 2700 106 1.9 2.5 1233 2716 BOCE Included
Pin On General Purpose Performance Series 2550 100 1.8-2.5 2.5-3.2 812-979 1786-2154 J250/BOCE
Sand and Gravel 2750 108 2.6-3.2 3.4-4.1 1026-1147 2262-2523 J250/BOCELight Material 2750 108 3.1-5.0 4.0-6.5 1096-1383 2416-3043 J250/BOCE
High Dump2550-3060
100-120 3.0-3.5 4.0-6.5 1695-2149 3737-4738 BOCE Included
Doze 2743 108 5.5 4.2 1506 3321 BOCELoad & Carry 2743 108 6.0 4.6 1528 3369 BOCE
PHB-Sec23(pg175-290).indd 235PHB-Sec23(pg175-290).indd 235 12/20/13 9:07 AM12/20/13 9:07 AM
23-236 Edition 44
Wheel LoadersIntegrated Toolcarriers
Model Interface Bucket TypeWidthRange
CapacityRange
WeightRange GET
mm in m3 yd3 kg lb938K Fusion General Purpose
Performance Series
2550-2750
100-108 2.5-2.9 3.2-3.8 961-1042 2118-2292 J250/BOCE
Light Material 2750 108 3.1-5.0 4.0-6.5 1075-1360 2370-2992 J250/BOCEMulti-Purpose 2550 100 2.1 2.7 1288 2834 BOCESide Dump 3105 122 1.9 2.5 1653 3644 BOCE IncludedHigh Dump 3060 120 4.1-5.0 5.4-6.5 2041-2123 4500-4680 BOCE IncludedGrapple 2697 106 2.7-2.9 3.5-3.8 1632-1673 3598-3688 J250/BOCEWaste 3059 120 4.0 5.2 1547 3410 BOCE IncludedWoodchip 3330 131 5.5 7.2 1795 3957 BOCE IncludedGrading 2700 106 1.9 2.5 1233 2716 BOCE Included
Pin On General Purpose Performance Series
2550-2750
100-108 2.4-2.8 3.2-3.8 968-1059 2134-2330 J250/BOCE
Sand and Gravel 2750 108 2.7-3.2 3.5-4.1 1075-1146 2365-2521 J250/BOCELight Material 2750 108 3.5-5.0 4.5-6.5 1178-1378 2596-3038 BOCE IncludedHigh Dump 3060 120 4.1-5.0 5.4-6.5 2065-2147 4553-4733 BOCE IncludedDoze 2927 115 6.0 4.6 1854 4088 BOCELoad & Carry 2927 115 6.75 5.2 1927 4249 BOCE
950K 962K
Fusion General Purpose Performance Series 2894 114 2.7-3.8 3.5-5.0 1367-1633 3014-3600 K80/BOCE
Material Handling Performance Series 2894 114 2.7-3.8 3.5-5.0 1373-1650 3027-3638 K80/BOCE
Rock Performance Series 2969 117 2.7-3.2 3.5-4.25 1992-2070 4711-4893 K90
Multi-Purpose 2943 116 2.9 3.75 2087 4601 BOCE IncludedSide Dump 3220 127 2.9 3.75 2348 5177 BOCE IncludedHigh Dump 2910 115 4.6-6.1 6.0-8.0 2672-2784 5891-6139 BOCE IncludedGrapple 3059 120 4.6 6.0 2824 6226 BOCE IncludedWaste 3059 120 5.2-6.1 6.75-8.0 2115-2285 4663-5038 BOCE IncludedWoodchip 3330 131 9.2-9.9 12.0-13.0 2371-2466 5227-5437 BOCE Included
Pin On General Purpose Performance Series 2894 114 2.7-3.8 3.5-5.0 1472-1778 3245-3920 K80/BOCE
Material Handling Performance Series 2894 114 2.7-3.8 3.5-5.0 1495-1787 3296-3940 K80/BOCE
Rock Performance Series 2969 117 2.9-3.2 3.75-4.25 1992-2070 4711-4893 K90
Multi-Purpose 2943 116 2.9 3.75 2099 4628 BOCE IncludedSide Dump 3226 127 2.9 3.75 2455 5413 BOCE IncludedHigh Dump 2910 115 4.6-6.1 6.0-8.0 2697-2812 5947-6201 BOCE IncludedGrapple 3059 120 4.6 6.0 2925 6449 BOCE IncludedWaste 3059 120 5.2-6.1 6.5-8.0 2250-2425 4960-5346 BOCE IncludedWoodchip 3330 131 9.2-9.9 12.0-13.0 2418-2516 5331-5547 BOCE IncludedDoze 3059 121 6.75 5.2 2273 5012 BOCELoad & Carry 3059 121 8.0 6.1 2610 5755 BOCE
Buckets● Americas North
PHB-Sec23(pg175-290).indd 236PHB-Sec23(pg175-290).indd 236 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-237
Wheel LoadersIntegrated Toolcarriers
23
Model Interface Bucket TypeWidthRange
CapacityRange
WeightRange GET
mm in m3 yd3 kg lb966K 966M
Fusion General Purpose Performance Series 3201 126 3.8-4.6 5.0-6.0 1965-2143 4332-4721 K90/BOCE
Material Handling Performance Series 3201 126 4.0-4.8 5.2-6.3 2068-2254 4559-4969 K90/BOCE
Coal Performance Series 3447 136 7.1 9.25 2865 6316 BOCE Included
Rock Performance Series 3255 128 3.4 4.5 2084 4595 K90
Multi Purpose 3220 127 3.1 4.0 2785 6140 BOCE IncludedSide Dump 3677 145 3.6 4.75 2832 6243 BOCE IncludedHigh Dump 3059 120 5.4 7.0 2862 6310 BOCE IncludedGrapple 3048 120 3.8 5.0 4380 9656 K90Waste 3323 131 6.5 8.5 2569 5664 BOCE IncludedWoodchip 3943 155 9.9 13.0 2543 5606 BOCE IncludedDoze 3357 132 8.5 6.5 3104 6844 BOCE IncludedLoad & Carry 3357 132 9.75 7.5 3311 7301 BOCE Included
Pin On General Purpose Performance Series 3201 126 3.8-4.6 5.0-6.0 2112-2260 4656-4982 K90/BOCE
Material Handling Performance Series 3201 126 4.0-4.8 5.25-6.25 2173-2350 4791-5181 K90/BOCE
Coal Performance Series 3447 136 7.1 9.25 2795 6162 BOCE Included
Rock Performance Series 3255 128 3.2-3.4 4.25-4.5 2362 5207 K90
Heavy Duty Rock 3251 128 3.6-4.0 4.75-5.25 2371-2751 5227-6065 J350/K90Multi Purpose 3226 127 3.1 4.0 2721 5999 K90Side Dump 3677 145 3.6 4.75 2858 6301 BOCE IncludedWaste 3357 132 6.5 8.5 2925 6449 BOCE Included
Woodchip3327-3937
131-155 8.0-9.9 10.5-13.0 2474-2543 5455-5542 BOCE Included
Buckets● Americas North
PHB-Sec23(pg175-290).indd 237PHB-Sec23(pg175-290).indd 237 12/20/13 9:07 AM12/20/13 9:07 AM
23-238 Edition 44
Wheel LoadersIntegrated Toolcarriers
Model Interface Bucket TypeWidthRange
CapacityRange
WeightRange GET
mm in m3 yd3 kg lb972K 972M
Fusion General Purpose Performance Series 3201 126 4.2-5.0 5.5-6.5 2026-2233 4467-4923 K90/BOCE
Material Handling Performance Series 3201 126 5.2 6.75 2274 5013 K90/BOCE
Coal Performance Series 3447 136 7.1 9.25 3199 7053 BOCE Included
Rock Performance Series 3255 128 3.6 4.75 2079 4583 K90
Multi Purpose 3220 127 3.1 4.0 2785 6140 BOCE IncludedSide Dump 3677 145 3.6 4.75 2832 6243 BOCE IncludedHigh Dump 3059 120 5.4 7.0 2862 6310 BOCE IncludedGrapple 3048 120 3.8 5.0 4380 9656 K90Waste 3323 131 6.5 8.5 2569 5664 BOCE IncludedWoodchip 3943 155 9.9 13.0 2543 5606 BOCE IncludedDoze 3357 132 8.5 6.5 3104 6844 BOCE IncludedLoad & Carry 3357 132 9.75 7.5 3311 7301 BOCE Included
Pin On General Purpose Performance Series 3193 126 4.2-5.0 5.5-6.5 2214-2383 4881-5254 K90/BOCE
Material Handling Performance Series 3193 126 4.6-5.2 6.0-6.75 2269-2389 5002-5276 K90/BOCE
Coal Performance Series 3447 136 7.1 9.25 3203 7061 BOCE Included
Rock Performance Series 3255 128 3.6-4.0 4.75-5.25 2250-2397 4960-5284 K90
Heavy Duty Rock 3251 128 3.6-4.0 4.75-5.25 2371-2751 5227-6065 J350/K90Multi Purpose 3226 127 3.1 4.0 2721 5999 K90Side Dump 3677 145 3.6 4.75 2858 6301 BOCE IncludedWaste 3357 132 6.5 8.5 2925 6449 BOCE Included
Woodchip3327-3937
131-155 8.0-9.9 10.5-13.0 2474-2543 5455-5542 BOCE Included
Slag 3250 128 3.4 4.5 4145 9138 K100966K 972K
Fusion Multi-Purpose 3220 127 2.9-3.1 3.75-4.0 2892 6375 BOCE IncludedSide Dump 3677 145 3.4-3.6 4.5-4.75 2832 6243 BOCE IncludedHigh Dump 3059 120 5.0-5.4 6.5-7.0 2904 6402 BOCE IncludedGrapple 3048 120 3.2-3.6 4.25-4.75 4380 9656 K90Waste 3357 132 6.2-6.5 8.1-8.5 2569 5664 BOCE IncludedWoodchip 3937 155 9.6-9.9 12.5-13.0 2543 5606 BOCE Included
Pin On Heavy Duty Rock 3251 125 3.4-4.0 4.5-5.25 2425-2949 5346-6501 K90/J350Multi-Purpose 3220 127 2.9-3.1 3.75-4.0 2806 6185 BOCE IncludedSide Dump 3677 145 3.4-3.6 4.5-4.75 2836 6252 BOCE IncludedWaste 3357 132 5.7-6.0 7.5-7.85 2837 6255 BOCE Included
Woodchip3327-3937
131-155 7.6-9.9 10.0-13.0 2474-2514 5455-5542 BOCE Included
Buckets● Americas North
PHB-Sec23(pg175-290).indd 238PHB-Sec23(pg175-290).indd 238 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-239
Wheel LoadersIntegrated Toolcarriers
23
Model Interface Bucket TypeWidthRange
CapacityRange
WeightRange GET
mm in m3 yd3 kg lb980K Pin On General Purpose
Performance Series 3405 134 5.4-6.0 7.0-7.85 2674-2853 5895-6290 K90/BOCE
Material Handling Performance Series 3405 134 5.7 7.5 2882 6354 K90/BOCE
Coal Performance Series 3638 143 8.2 10.75 3663 8075 BOCE Included
Rock Performance Series 3495 138 4.4 5.75 2925 6448 K90
Heavy Duty Quarry Rock
3505-3568
138-140 4.4-4.6 5.75-6.0 3306-3686 7288-8125 BOCE Included
Waste 3886 153 9.8 12.75 3908 8615 BOCE IncludedWoodchip 4166 164 11.5 15.0 3887 8570 BOCE IncludedDoze 3882 153 13.0 9.9 4210 9283 BOCE IncludedLoad & Carry 3882 153 14.0 10.7 4438 9786 BOCE IncludedSlag 3394 134 3.8 5.0 5302 11,689 K130
986H Pin On Rock 3772 148.5 5.4-6.1 7-8 3692-3907 8139-8693 K110988K Pin On General Purpose
Performance Series 3855 152 6.9-8.4 9.0-11.0 4539-4994 10,007-11,010 K110
Rock Performance Series 4020 158 6.4-7.7 8.3-10.0 4880-5263 10,759-11,603 K130
Heavy Duty Rock Performance Series 4080 161 6.4 8.3 6360 14,021 K130
Heavy Duty Granite Performance Series 3986 157 6.4 8.3 7433 16,385 K130
Serrated Edge Rock 3968 156 6.4-6.9 8.3-9.0 5455-5634 12,026-12,421 —
Iron Ore 3922 154 4.7 6.2 5771 12,723 K130
Coal4120-4450
162-175 11.5-14.5 15.0-19.0 6023-7000 13,278-15,400 BOCE Included
Slag3900-4032
154-159 5.4-6.4 7.0-8.3 7633-8454 16,828-18,638
J600/Serrated Edge
Buckets● Americas North
PHB-Sec23(pg175-290).indd 239PHB-Sec23(pg175-290).indd 239 12/20/13 9:07 AM12/20/13 9:07 AM
23-240 Edition 44
Wheel LoadersIntegrated Toolcarriers
Model Interface Bucket TypeWidthRange
CapacityRange
WeightRange GET
mm in m3 yd3 kg lb988H Pin On General Purpose
Performance Series 3960 156 6.9-7.7 9.0-10.0 2063-5384 11,138-11,845 K110/BOCE
General Purpose 3860 152 7.7 10.0 4895 10,773 BOCE IncludedRock Performance
Series 4020 158 6.4-7.7 8.3-10.0 4944-5324 10,877-11,713 K130Rock 3980 157 7.7 10.0 4452 9812 K110Heavy Duty Rock
Performance Series 4080 161 6.4 8.3 6348 13,966 K130
Heavy Duty Granite 3980 157 6.4 8.33 7648 16,826 K130
Slag3866-3970
152-156 5.3-6.4 7.0-8.33 7200-7653 15,840-16,837
K130/J600/ Weld-on edge
Coal4120-4450
162-175 11.5-14.5 15.0-19.0 5910-7000 13,030-15,400 BOCE Included
Coal Seam 3810 150 6.8 8.5 4450 9790 J460/BOCEIron Ore 3940 155 4.4 5.75 5475 12,070 K130Serrated Edge
Rock 3970 156 6.9 9.0 4790 10,540 N/A990H Pin On Rock Performance
Series 4610 182 8.6-10.0 11.25-13.0 7247-7497 15,977-16,528 K130Heavy Duty Rock
Performance Series 4670 184 8.6 11.25 8980 19,798 K130
Heavy Duty Granite Performance Series 4634 182 8.6 11.25 11 451 25,245 K150
Slag4450-4500
175-177 8.5-9.2 11.2-12.0 9149-9613 20,127-21,149
Weld-on edge included
Coal 4370 172 13.4 17.5 7460 16,410 BOCE IncludedIron Ore 4450 175 7.0 9.2 8525 18,750 K150Serrated Edge
Rock 4610 182 9.5 12.4 8140 17,910 N/AN/A = Not Applicable
Buckets● Americas North
PHB-Sec23(pg175-290).indd 240PHB-Sec23(pg175-290).indd 240 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-241
Wheel LoadersIntegrated Toolcarriers
23
Buckets● Americas North
Model Interface Bucket TypeWidthRange
CapacityRange
WeightRange GET
mm in m3 yd3 kg lb992K Pin On
Rock4824-4884
190-192 10.7-12.2 14.0-16.0 9382-10 574 20,684-23,262 K150/K170
Heavy Duty Rock 5068 200 10.7 14.0 11 560 25,485 K170High Abrasion
Rock 5068 200 10.7 14.0 11 927 26,295 K150Heavy Duty
Granite 5165 203 10.7 14.0 13 720 30,247 K150Coal 6170 243 19.0 25.0 12 504 27,506 BOCE IncludedIron Ore 4900 193 9.0 11.8 11 172 24,577 K150Serrated Edge
Rock 4824 190 12.3 16.0 10 282 22,620 N/A993K Pin On Rock 5068 200 12.2-14.5 16.0-19.0 12 864-14 209 28,301-31,260 K170
High Abrasion Rock 5160 203 12.2-13.0 16.0-17.0 15 205-15 456 33,451-34,004 K170
Heavy Duty Granite 5160 203 13.0 17.0 17 418 38,320 K170
Coal 6300 248 23.0 31.0 17 673 38,880 K170Iron Ore 5160 203 10.0 13.0 14 063 30,940 K170Serrated Edge
Rock 5080 200 15.0 19.5 13 915 30,615 N/A994H Pin On
Rock5650-6220
222-245 14.9-19.1 19.5-25.0 19 302-21 777 42,465-47,909 J800
Coal6220-6300
245-248 31.3-35.9 41.0-47.0 22 211-23 598 48,864-51,916
J700/Weld-on edge
N/A = Not Applicable
PHB-Sec23(pg175-290).indd 241PHB-Sec23(pg175-290).indd 241 12/20/13 9:07 AM12/20/13 9:07 AM
23-242 Edition 44
Wheel LoadersIntegrated Toolcarriers
Model Interface Bucket TypeWidthRange
CapacityRange
WeightRange GET
mm in m3 yd3 kg lb924K Fusion General Purpose 2550 100 1.9 -2.5 2.5-3.2 775-963 1705-2119 J250/BOCE
Light Material 2750 108 3.5-5.0 4.5-6.5 1161-1360 2554-2992 BOCEMulti-Purpose 2550 100 2.1 2.7 1288 2834 J250/BOCEHigh Dump 2550-3060 100-120 3.0-5.0 4.0-6.5 1688-2123 3721-4680 BOCE
Pin On General Purpose 2550 100 1.9 -2.3 2.5-3.0 812-893 1786-1965 J250/BOCESand and Gravel 2750 108 2.6-3.2 3.4-4.1 1026-1147 2262-2523 J250/BOCELight Material 2750 108 3.1-5.0 4.0-6.5 1096-1383 2416-3043 BOCEHigh Dump 2550-3060 100-120 3.0-5.0 4.0-6.6 1096-2149 3737-4738 BOCE
930K Fusion General Purpose 2550 100 1.9 -2.5 2.5-3.2 775-963 1705-2119 J250/BOCELight Material 2750 108 3.5-5.0 4.5-6.5 1161-1360 2554-2992 BOCEMulti-Purpose 2550 100 2.1 2.7 1288 2834 J250/BOCEHigh Dump 2550-3060 100-120 3.0-5.0 4.0-6.5 1688-2123 3721-4680 BOCE
Pin On General Purpose 2550 100 1.9 -2.5 2.5-3.2 812-979 1786-2154 J250/BOCESand and Gravel 2750 108 2.6-3.2 3.4-4.1 1026-1147 2262-2523 J250/BOCELight Material 2750 108 3.1-5.0 4.0-6.5 1096-1383 2416-3043 BOCEHigh Dump 2550-3060 100-120 3.0-3.5 4.0-6.5 1695-2149 3737-4738 BOCE
938K Fusion General Purpose 2550-2750 100-108 2.5 -2.9 3.2-3.8 961-1042 2118-2292 J250/BOCELight Material 2750 108 3.1-5.0 4.0-6.5 1075-1360 2370-2992 BOCEMulti-Purpose 2550 100 2.1 2.7 1288 2834 J250/BOCEHigh Dump 3060 120 4.1-5.0 5.4-6.5 2041-2123 4500-4680 BOCE
Pin On General Purpose 2550-2750 100-108 2.4-2.8 3.2-3.8 968-1059 2134-2330 J250/BOCESand and Gravel 2750 108 2.7-3.2 3.5-4.1 1067-1147 2347-2523 J250/BOCELight Material 2750 108 3.5-5.0 4.5-6.5 1178-1378 2596-3038 BOCEHigh Dump 3060 120 4.1-5.0 5.4-6.5 2065-2147 4553-4733 BOCE
Buckets● Americas South
PHB-Sec23(pg175-290).indd 242PHB-Sec23(pg175-290).indd 242 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-243
Wheel LoadersIntegrated Toolcarriers
23
Model Interface Bucket TypeWidthRange
CapacityRange
WeightRange GET
mm in m3 yd3 kg lb950H962H
Fusion General Purpose Performance Series 2894 114 2.9-3.4 3.75-4.5 1534-1610 3382-3549 K80/BOCE
Material Handling 2896 114 3.3-3.8 4.25-5.0 1701 3750 K80/BOCECoal 3302 130 5.7-5.9 7.5-7.75 1928 4251 BOCERock 2969 117 2.7-3.25 3.75-4.25 1588-1638 3500-3611 K90Multi-Purpose 2946 116 2.87 3.75 2087 4600 BOCE IncludedSide Dump 3226 127 2.87 3.75 2340 5160 BOCE IncludedHigh Dump 2921 115 4.2-4.6 5.5-6.0 2657 5857 BOCE IncludedGrapple 2921 115 3.0-3.25 4.0-4.25 2139 4715 K80/BOCEWaste 3048 120 5.2 6.75 2163 4769 BOCE IncludedWoodchip 3327 131 9.2 12.0 2121 4676 BOCE Included
Pin On General Purpose Performance Series 2894 114 2.5-3.6 3.25-4.75 1419-1636 3128-3607 K80/BOCE
Material Handling Performance Series 2894 114 3.0-3.8 3.9-5.0 1538-1684 3391-3713 K80/BOCE
Coal Performance Series 3040 120 4.2-5.2 5.2-6.8 TBD BOCE Included
Rock Performance Series 2972 117 2.9-3.1 3.8-4.1 1796-1838 3560-4052 K90
Multi-Purpose 2938 116 2.9 3.75 2015 4440 BOCE IncludedSide Dump 3226 127 2.9 3.75 2406 5300 BOCE IncludedWaste 3058 120 5.2 6.75 2376 5235 BOCE IncludedWoodchip 3327 131 9.2 12.0 2279 5020 BOCE Included
966H Fusion General Purpose Performance Series 3201 126 3.6-4.6 4.75-6.0 1965-2143 4332-4724 K90/BOCE
Material Handling Performance Series 3201 126 3.8-4.880 5.0-6.3 2068-2254 4559-4969 K90/BOCE
Coal Performance Series 3447 136 6.9 9.0 2865 6316 BOCE Included
Rock Performance Series 3255 128 3.2 4.5 2084 4595 K90
Pin On General Purpose Performance Series 3201 126 3.6-4.6 4.75-6.0 2112-2260 4656-4982 K90/BOCE
Material Handling Performance Series 3201 126 3.8-4.880 5.0-6.3 2173-2350 4791-5181 K90/BOCE
Coal Performance Series 3447 136 6.9 9.0 2795 6162 BOCE Included
Rock Performance Series 3255 128 3.2 4.5 2362 5207 K90
Buckets● Americas South
PHB-Sec23(pg175-290).indd 243PHB-Sec23(pg175-290).indd 243 12/20/13 9:07 AM12/20/13 9:07 AM
23-244 Edition 44
Wheel LoadersIntegrated Toolcarriers
Buckets● Americas South
Model Interface Bucket TypeWidthRange
CapacityRange
WeightRange GET
mm in m3 yd3 kg lb972H Fusion General Purpose
Performance Series 3201 126 4.0-5.0 5.25-6.5 2026-2212 4467-4877 K90/BOCE
Material Handling Performance Series 3201 126 5.0-5.2 6.5-6.75 2274 5013 K90/BOCE
Coal Performance Series 3447 136 6.9 9.0 3199 7053 BOCE Included
Rock Performance Series 3225 128 3.4-3.6 4.5-4.75 2079 4583 K90
Pin On General Purpose Performance Series 3201 126 4.0-5.0 5.25-6.5 2214-2315 4881-5104 K90/BOCE
Material Handling Performance Series 3201 126 4.4-5.2 5.75-6.75 2269-2389 5002-5267 K90/BOCE
Coal Performance Series 3447 136 6.9 9.0 3203 7061 BOCE Included
Rock Performance Series 3255 128 3.4-4.0 4.5-5.25 2250-2397 4960-5284 K90
966H972H
Fusion Multi-Purpose 3220 127 2.9-3.1 3.75-4.0 2892 6375 BOCE IncludedSide Dump 3677 145 3.4-3.6 4.5-4.75 2832 6243 BOCE IncludedHigh Dump 3059 120 5.0-5.4 6.5-7.0 2904 6402 BOCE IncludedGrapple 3048 120 3.2-3.6 4.25-4.75 4380 9656 K90/BOCEWaste 3357 132 6.2-6.5 8.1-8.5 2569 5664 BOCE IncludedWoodchip 3937 155 9.6-9.9 12.5-13.0 2543 5606 BOCE Included
Pin On Heavy Duty Rock 3251 125 3.4-4.0 4.5-5.25 2425-2949 5346-6501 K90/J350Multi-Purpose 3220 127 2.9-3.1 3.75-4.0 2806 6185 BOCE IncludedSide Dump 3677 145 3.4-3.6 4.5-4.75 2836 6252 BOCE IncludedWaste 3357 132 5.7-6.0 7.5-7.85 2837 6255 BOCE IncludedWoodchip 3327-3937 131-155 7.6-9.9 10.0-13.0 2474-2514 5455-5542 BOCE Included
980H Pin On General Purpose Performance Series 3405 134 5.0-6.1 6.5-8.0 2572-2726 5670-6010 K100/BOCE
Material Handling Performance Series 3405 134 5.5-5.7 7.25-7.5 2780 6129 K100/BOCE
Coal Performance Series 3638 143 7.8 10.25 3213 7083 BOCE Included
Rock Performance Series 3492 137 4.0-4.4 5.25-5.75 2801 6175 K100
Heavy Duty General Purpose 3450 136 5.4-5.7 7.0-7.5 3439 7582 BOCE
Heavy Duty Quarry Rock
3505-3568 138-140 4.0-4.6 5.25-6.0 306-3686 7288-8125 K110
Slag 3394 134 3.8 5.0 5302 11,689 K130Waste 3886 153 9.3-9.8 12.25-12.75 3908 8615 BOCE IncludedWoodchip 4166 164 11.3-11.5 14.75-15.0 3887 8570 BOCE Included
PHB-Sec23(pg175-290).indd 244PHB-Sec23(pg175-290).indd 244 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-245
Wheel LoadersIntegrated Toolcarriers
23
Buckets● Americas South
Model Interface Bucket TypeWidthRange
CapacityRange
WeightRange GET
mm in m3 yd3 kg lb986H Pin On Rock 3772 148.5 5.4-6.1 7-8 3692-3907 8139-8693 K110988H Pin On General Purpose
Performance Series 3900 154 6.9-7.7 9.0-10.0 4937-5158 10,861-11,407 K110/BOCE
General Purpose 3860 152 7.7 10.0 4895 10,773 BOCE IncludedRock Performance
Series 4020 158 6.4-7.7 8.3-10.0 4787-6221 10,531-11,341 K130Rock 3980 157 7.7 10.0 4452 9812 K110Heavy Duty Rock
Performance Series 4080 161 6.4 8.3 6221 13,686 K130
Heavy Duty Granite 3980 157 6.4 8.33 7648 16,826 K130
Slag 3866-3970 152-156 5.3-6.4 7.0-8.33 7200-7653 15,840-16,837K130/J600/
Weld-on EdgeCoal 4120-4450 162-175 11.5-14.5 15.0-19.0 5910-7000 13,030-15,400 BOCE IncludedCoal Seam 3810 150 6.8 8.5 4450 9790 J460/BOCEIron Ore 3940 155 4.4 5.75 5475 12,070 K130Serrated Edge
Rock 3970 156 6.9 9.0 4790 10,540 N/A988K Pin On General Purpose
Performance Series 3855 152 6.9-8.4 9.0-11.0 4539-4994 10,007-11,010 K110
Rock Performance Series 4020 158 6.4-7.7 8.3-10.0 4880-5263 10,759-11,603 K130
Heavy Duty Rock Performance Series 4080 161 6.4 8.3 6360 14,021 K130
Heavy Duty Granite Performance Series 3986 157 6.4 8.3 7433 16,385 K130
Serrated Edge Rock 3968 156 6.4-6.9 8.3-9.0 5455-5634
12,026-12,421 —
Iron Ore 3922 154 4.7 6.2 5771 12,723 K130
Coal4120-4450 162-175 11.5-14.5 15.0-19.0 6023-7000
13,278-15,400 BOCE Included
Slag3900-4032 154-159 5.4-6.4 7.0-8.3 7633-8454
16,828-18,638
J600/Serrated Edge
N/A = Not Applicable
PHB-Sec23(pg175-290).indd 245PHB-Sec23(pg175-290).indd 245 12/20/13 9:07 AM12/20/13 9:07 AM
23-246 Edition 44
Wheel LoadersIntegrated Toolcarriers
Buckets● Americas South
Model Interface Bucket TypeWidthRange
CapacityRange
WeightRange GET
mm in m3 yd3 kg lb990H Pin On Rock
Performance Series 4610 182 8.60-10.0 11.25-13.0 7247-7497 15,977-16,528 K130
Heavy Duty Rock Performance Series 4670 184 8.60 11.25 8980 19,798 K130
Heavy Duty Granite Performance Series 4634 182 8.60 11.25 12 055 26,520 K150
Slag 4450-4500 175-177 8.5-9.2 11.2-12.0 8882-9450 19,540-20,790Weld-on Edge
IncludedCoal 4370 172 13.4 17.5 8400 16,410 BOCE IncludedIron Ore 4450 175 7.0 9.2 8523 18,480 K150Serrated Edge
Rock 4610 182 9.5 12.5 8155 17,940 N/A992K Pin On Rock 4824-4884 190-192 10.7-12.2 14.0-16.0 9382-10 574 20,684-23,262 K150/K170
Heavy Duty Rock 5068 200 10.7 14.0 11 560 25,485 K170High Abrasion
Rock 5068 200 10.7 14.0 11 927 26,295 K150Heavy Duty
Granite 5165 203 10.7 14.0 13 720 30,247 K150Coal 6170 243 19.0 25.0 12 504 27,506 BOCE IncludedIron Ore 4900 193 9.0 11.8 11 172 24,577 K150Serrated Edge
Rock 4824 190 12.3 16.0 10 282 22,620 N/A993K Pin On Rock 5068 200 12.2-14.5 16.0-19.0 12 864-14 209 28,301-31,260 K170
High Abrasion Rock 5160 203 12.2-13.0 16.0-17.0 15 205-15 456 33,451-34,004 K170
Heavy Duty Granite 2160 203 13.0 17.0 17 418 38,320 K170
Coal 6300 248 23.0 31.0 17 673 38,880 K170Iron Ore 5160 203 10.0 13.0 14 063 30,940 K170Serrated Edge
Rock 5080 200 15.0 19.5 13 915 30,615 N/A994H Pin On Rock 5650-6220 222-245 14.9-19.1 19.5-25.0 19 302-21 777 42,465-47,909 J800
Coal 6220-6300 245-248 31.3-35.9 41.0-47.0 22 211-23 598 48,864-51,916J700/Weld-on
EdgeN/A = Not Applicable
PHB-Sec23(pg175-290).indd 246PHB-Sec23(pg175-290).indd 246 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-247
Wheel LoadersIntegrated Toolcarriers
23
Buckets● Europe, Africa, Middle East
Model Interface Bucket TypeWidthRange
CapacityRange
WeightRange GET
mm in m3 yd3 kg lb924K Fusion General Purpose 2550 100 1.9-2.5 2.5-3.2 775-963 1705-2119 J250/BOCE
Light Material 2750 108 3.5-5.0 4.5-6.5 1161-1360 2554-2992 J250/BOCEMulti-Purpose 2550 100 2.1 2.7 1288 2834 BOCEHigh Dump 2550-3060 100-120 3.0-5.0 4.0-6.5 1688-2123 3721-4680 BOCE
ISO General Purpose 2550 100 2.2-2.3 2.9-3.0 792-828 1746-1825 J250/BOCEGrading 2600-2900 102-114 1.78-2.01 2.3-2.6 847-922 1867-2033 BOCELight Material 2750 108 3.5-5.0 4.5-6.5 2454-2859 5410-6303 J250/BOCEHigh Dump 2550-3060 100-120 3.0-5.0 4.0-6.5 1627-2081 3587-4588 BOCE
Pin On General Purpose 2550 100 1.9-2.2 2.5-3.0 812-893 1786-1965 J250/BOCELight Material 2750 108 3.1-5.0 4.0-6.5 1096-1383 2416-3043 J250/BOCEHigh Dump 2550-3060 100-120 3.0-5.0 4.0-6.5 1695-2149 3737-4738 BOCESand & Gravel 2750 108 2.6-3.2 3.4-4.1 1026-1147 2262-2523 J250/BOCE
930K Fusion General Purpose 2550 100 1.9-2.5 2.5-3.2 775-963 1705-2119 J250/BOCELight Material 2750 108 3.5-5.0 4.5-6.5 1161-1360 2554-2992 J250/BOCEMulti-Purpose 2550 100 2.1 2.7 1288 2834 BOCEHigh Dump 2550-3060 100-120 3.0-5.0 4.0-6.5 1688-2123 3721-4680 BOCE
ISO General Purpose 2550 100 2.2-2.3 2.9-3.0 792-828 1746-1825 J250/BOCEGrading 2600-2900 102-114 1.78-2.01 2.3-2.6 847-922 1867-2033 BOCELight Material 2750 108 3.5-5.0 4.5-6.5 2454-2859 5410-6303 J250/BOCEHigh Dump 2550-3060 100-120 3.0-5.0 4.0-6.5 1627-2081 3587-4588 BOCE
Pin On General Purpose 2550 100 1.8-2.4 2.5-3.2 812-979 1786-2154 J250/BOCELight Material 2750 108 3.1-5.0 4.0-6.5 1096-1383 2416-3043 J250/BOCEHigh Dump 2550-3060 100-120 3.0-3.5 4.0-6.5 1695-2149 3737-4738 BOCESand & Gravel 2750 108 2.6-3.2 3.4-4.1 1026-1147 2262-2523 BOCE
938K Fusion General Purpose 2550-2750 100-108 2.5-2.9 3.2-3.8 961-1042 2118-2292 J250/BOCELight Material 2750 108 3.1-5.0 4.0-6.5 1075-1360 2370-2992 J250/BOCEMulti-Purpose 2550 100 2.1 2.7 1288 2834 BOCEHigh Dump 3060 120 4.1-5.0 5.4-6.5 2041-2123 4500-4680 BOCE
ISO General Purpose 2750 108 2.5-2.7 3.2-3.5 915-959 2017-2114 J250/BOCEGrading 2600-2900 102-114 1.78-2.01 2.3-2.6 847-922 1867-2033 BOCELight Material 2750 108 3.5-5.0 4.5-6.5 2454-2859 5410-6303 J250/BOCEHigh Dump 3060 120 4.1-5.0 5.4-6.5 2001-2081 4409-4588 BOCE
Pin On General Purpose 2550-2750 100-108 2.4-2.8 3.2-3.8 968-1059 2134-2330 J250/BOCELight Material 2750 108 3.5-5.0 4.5-6.5 1178-1378 2596-3038 BOCEHigh Dump 3060 120 4.1-5.0 5.4-6.5 2065-2147 4553-4733 BOCESand & Gravel 2750 108 2.7-3.2 3.5-4.1 1075-1146 2365-2521 J250/BOCE
PHB-Sec23(pg175-290).indd 247PHB-Sec23(pg175-290).indd 247 12/20/13 9:07 AM12/20/13 9:07 AM
23-248 Edition 44
Wheel LoadersIntegrated Toolcarriers
Buckets● Europe, Africa, Middle East
Model Interface Bucket TypeWidthRange
CapacityRange
WeightRange GET
mm in m3 yd3 kg lb950K Fusion General Purpose
Performance Series2894 114 2.9-3.6 3.79-4.7 1449-1550 3195-3417 K80/BOCE
Material Handling Performance Series 2904-2994 114-117 3.1-3.4 4.05-4.45 1535-2070 3384-4564 K80/BOCE
Pin On General Purpose Performance Series 2894 114 2.9-3.6 3.79-4.7 1556-1683 3430-3710 K80/BOCE
Material Handling Performance Series 2904-2994 114-117 3.1-3.4 4.05-4.45 1543-2060 3402-4541 K80/BOCE
Rock Performance Series 2969 117 2.9 3.8 1992 4382 K90
962K Fusion General Purpose Performance Series 2894 114 3.2-3.6 4.18-4.7 1517-1550 3344-3417 K80/BOCE
Material Handling Performance Series 2904-2994 114-117 3.3-3.8 4.32-4.79 1574-2183 3470-4812 K80/BOCE
Pin On General Purpose Performance Series 2894 114 3.2-3.6 4.18-4.7 1647-1683 3631-3710 K80/BOCE
Material Handling Performance Series 2904-2994 114-117 3.3-3.8 4.32-4.79 1582-2173 3488-4790 K80/BOCE
Rock Performance Series 2969 117 3.2 4.19 2070 4554 K90
966K Fusion General Purpose Performance Series 3201 126 3.6-4.6 4.75-6.0 1943-2082 4283-4590 K90/BOCE
Material Handling Performance Series 3201 126 3.8-4.8 5.0-6.3 2068-2254 4559-4969 K90/BOCE
Rock Performance Series 3252 128 3.2-3.4 4.25-4.5 2084 4595 K90
Pin On General Purpose Performance Series 3201 126 3.6-4.6 4.75-6.0 1985-2194 4367-4827 K90/BOCE
Material Handling Performance Series 3000-3289 118-129 3.8-4.8 5.0-6.3 2100-3084 4620-6785 K90/BOCE
Rock Performance Series 3252 128 3.2-3.4 4.25-4.5 2175 4785 K90
972K Fusion General Purpose Performance Series 3201 126 4.0-5.0 5.25-6.5 1966-2147 4325-4723 K90/BOCE
Material Handling Performance Series 3201 126 4.4-5.2 5.72-6.76 1907-2274 4195-5003 K90/BOCE
Rock Performance Series 3225 128 3.4-3.6 4.5-4.75 2099 4618 K90
Pin On General Purpose Performance Series 3201 126 4.0-5.0 5.25-6.5 2089-2281 4596-5018 K90/BOCE
Material Handling Performance Series 3201-3294 126-130 4.4-5.2 5.75-6.75 2248-3122 4946-6868 K90/BOCE
Rock Performance Series 3252-3350 128-132 3.4-4.0 4.5-5.25 2209-3039 4860-6686 K90/K100
980K Pin On General Purpose Performance Series 3413 134 5.0-6.0 6.5-7.8 2572-2831 5670-6228 K100/BOCE
Material Handling Performance Series 3413-3580 134-141 5.5-5.7 7.25-7.5 2786-4095 6149-9009 K100/BOCE
Rock Performance Series 3510-3645 138-144 4.5-5.4 5.85-7.02 3058-4335 6728-9537 K100/K110
PHB-Sec23(pg175-290).indd 248PHB-Sec23(pg175-290).indd 248 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-249
Wheel LoadersIntegrated Toolcarriers
23
Buckets● Europe, Africa, Middle East
Model Interface Bucket Type Width Capacity GETmm in m3 yd3
988H Pin On General Purpose 3900 153.5 6.9 9.0 StraightGeneral Purpose 3900 153.5 7.6 9.9 Straight
Rock 4020 158.3 6.4 8.4 SpadeRock 4020 158.3 6.9 9.0 SpadeRock 4013 158.0 7.7 10.1 SpadeRock 3980 156.7 7.6 9.9 Spade
Heavy Duty Rock 4080 160.6 6.4 8.4 Spade Heavy Duty Granite 3988 157.0 6.4 8.4 Spade Iron Ore 3940 155.1 4.4 5.8 Spade Serrated Edge 3800 149.6 6.4 8.4 V-Serrated
Serrated Edge 3968 156.2 6.9 9.0 V-Serrated Coal 4120 162.2 11.5 15.0 Straight
Coal 4118 162.1 13 17.0 Straight Slag 3899 153.5 6.5 8.5 Serrated
Slag 3860 152.0 5.4 7.1 SpadeSlag 3962 156.0 5.3 6.9 StraightSlag 3900 153.5 5.3 6.9 Straight
990H Pin On Rock 4610 181.5 9.2 12.0 SpadeRock 4450 175.2 8.6 11.2 Spade
Heavy Duty Rock 5409 213.0 8.55 11.2 Spade Heavy Duty Granite 4636 182.5 8.6 11.2 Spade Iron Ore 4450 175.2 7.03 9.2 Spade Serrated Edge 4450 175.2 8.6 11.2 V-Edge
Serrated Edge 4610 181.5 9.1 11.9 V-EdgeSerrated Edge 4610 181.5 9.5 12.4 Serrated Spade
Coal 4500 177.2 8.6 11.2 Straight Slag 4450 175.2 9.2 12.0 Serrated Spade
Slag 4500 177.2 8.6 11.2 Serrated Spade 992G Pin On Serrated Edge 4826 190.0 11.5 15.0 V-Serrated
Serrated Edge 4826 190.0 12.3 16.1 V-Serrated 992K Pin On Rock 4824 189.9 10.7 14.0 Spade
Rock 4824 189.9 11.5 15.0 SpadeRock 4824 189.9 12.2 16.0 Spade
Heavy Duty Rock 5080 200.0 10.7 14.0 SpadeHeavy Duty Granite 5156 203.0 10.7 14.0 Spade
Iron Ore 4900 192.9 9 11.8 Spade Serrated Edge 4824 189.9 12.3 16.1 V-Serrated Coal 6170 242.9 18.9 24.7 Straight
PHB-Sec23(pg175-290).indd 249PHB-Sec23(pg175-290).indd 249 12/20/13 9:07 AM12/20/13 9:07 AM
23-250 Edition 44
Wheel LoadersIntegrated Toolcarriers
Buckets● Europe, Africa, Middle East
Model Interface Bucket Type Width Capacity GETmm in m3 yd3
993K Pin On Rock 5080 200.0 12.2 16.0 SpadeRock 5080 200.0 13 17.0 SpadeRock 5080 200.0 13.8 18.0 SpadeRock 5080 200.0 14.5 19.0 Spade
High Abrasion 5160 203.1 12.2 16.0 SpadeHigh Abrasion 5160 203.1 13 17.0 Spade
Heavy Duty Granite 5160 203.1 13 17.0 Spade Iron Ore 5160 203.1 10 13.1 Spade Serrated Edge 5080 200.0 14.9 19.5 V-Serrated Coal 6300 248.0 23.7 31.0 Straight994F Pin On Rock 5650 222.4 15 19.6 Spade
Rock 5650 222.4 17 22.2 SpadeRock 5650 222.4 19 24.9 SpadeRock 6220 244.9 18 23.5 SpadeRock 6220 244.9 19 24.9 Spade
Coal 6220 244.9 31.5 41.2 StraightCoal 6300 248.0 36 47.1 V-Serrated
PHB-Sec23(pg175-290).indd 250PHB-Sec23(pg175-290).indd 250 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-251
Wheel LoadersIntegrated Toolcarriers
23
Buckets● Europe, Africa, Middle East
● High Dump Buckets
Model Capacity Width WeightDump Clearance Maximum Material Density
Standard Lift High Lift Standard Lift High Liftm3 yd3 mm in kg lb mm in mm in kg/m3 lb/yd3 kg/m3 lb/yd3
950H 5.1 6.7 3000 118.1 2662 5869 4543 178.9 5147 202.6 873 1471 867 14617.2 9.4 3200 126.0 3444 7593 4625 182.1 5247 206.6 550 927 552 9309.0 11.8 3400 133.9 3847 8481 4496 177.0 5126 201.8 404 681 410 691
950K 5.1 6.7 3000 118.1 2620 5776 4567 179.8 5022 197.7 934 1574 829 13977.2 9.4 3200 126.0 3500 7716 4600 181.1 5100 200.8 550 927 470 7929.0 11.8 3400 133.9 3900 8598 4650 183.1 5150 202.8 410 691 350 590
962H 5.1 6.7 3000 118.1 2662 5869 4543 178.9 5147 202.6 995 1677 715 12057.2 9.4 3200 126.0 3444 7593 4625 182.1 5247 206.6 635 1070 434 7329.0 11.8 3400 133.9 3847 8481 4496 177.0 5126 201.8 472 796 313 528
962K 5.1 6.7 3000 118.1 2620 5776 4567 179.8 5022 197.7 934 1574 829 13977.2 9.4 3200 126.0 3500 7716 4800 189.0 5100 200.8 600 1011 643 10849.0 11.8 3400 133.9 3900 8598 4850 190.9 5150 202.8 450 758 480 809
966H 6.7 8.8 3200 126.0 3598 7932 4909 193.3 5677 223.5 940 1584 975 164311.5 15.0 3600 141.7 5021 11,069 4950 194.9 5500 216.5 444 748 450 758
966K 6.7 8.8 3200 126.0 3598 7932 4909 193.3 5677 223.5 964 1625 988 166511.5 15.0 3600 141.7 5021 11,069 4950 194.9 5500 216.5 429 723 427 720
972H 6.7 8.8 3200 126.0 3598 7932 5003 197.0 5677 223.5 1076 1814 984 165911.5 15.0 3600 141.7 5021 11,069 5170 203.5 5500 216.5 496 836 435 733
972K 6.7 8.8 3200 126.0 3598 7932 4909 193.3 5677 223.5 964 1625 988 166511.5 15.0 3600 141.7 5021 11,069 5170 203.5 5500 216.5 503 848 446 752
PHB-Sec23(pg175-290).indd 251PHB-Sec23(pg175-290).indd 251 12/20/13 9:07 AM12/20/13 9:07 AM
23-252 Edition 44
Wheel LoadersIntegrated Toolcarriers
Buckets● Australia/New Zealand
Model Interface Bucket TypeWidthRange
CapacityRange
WeightRange GET
mm in m3 yd3 kg lb924K Fusion General Purpose 2550 100 1.9 -2.5 2.5-3.2 775-963 1705-2119 J250/BOCE
Light Material 2750 108 3.5-5.0 4.5-6.5 1161-1360 2554-2992 BOCEMulti-Purpose 2550 100 2.1 2.7 1288 2834 J250/BOCESide Dump 3105 122 1.9 2.5 1653 3644 BOCEHigh Dump 2550-3060 100-120 3.0-5.0 4.0-6.5 1688-2123 3721-4680 BOCEGrapple 2697 106 2.7-2.9 3.5-3.8 1632-1673 3598-3688 J250/BOCEWaste 3059 120 3.6-4.0 4.7-5.2 1416-1547 3122-3410 BOCEWoodchip 3330 131 4.9-5.5 6.4-7.2 1717-1795 3785-3957 BOCEGrading 2700 106 1.9 2.5 1233 2716 BOCE
ISO General Purpose 2550-2750 100-108 2.1-2.9 2.7-3.8 775-997 1705-2193 J250/BOCEPin On General Purpose 2550 100 1.9-2.2 2.5-3.0 812-893 1786-1965 J250/BOCE
Sand and Gravel 2750 108 2.6-3.2 3.4-4.1 1026-1147 2262-2523 J250/BOCELight Material 2750 108 3.1-5.0 4.0-6.5 1096-1383 2416-3043 BOCEHigh Dump 2550-3060 100-120 3.0-5.0 4.0-6.5 1695-2149 3737-4738 BOCE
930K Fusion General Purpose 2550 100 1.9 -2.5 2.5-3.2 775-963 1705-2119 J250/BOCELight Material 2750 108 3.5-5.0 4.5-6.5 1161-1360 2554-2992 BOCEMulti-Purpose 2550 100 2.1 2.7 1288 2834 J250/BOCESide Dump 3105 122 1.9 2.5 1653 3644 BOCEHigh Dump 2550-3060 100-120 3.0-5.0 4.0-6.5 1688-2123 3721-4680 BOCEGrapple 2697 106 2.7-2.9 3.5-3.8 1632-1673 3598-3688 J250/BOCEWaste 3059 120 3.6-4.0 4.7-5.2 1416-1547 3122-3410 BOCEWoodchip 3330 131 4.9-5.5 6.4-7.2 1717-1795 3785-3957 BOCEGrading 2700 106 1.9 2.5 1233 2716 BOCE
ISO General Purpose 2550-2750 100-108 2.1-2.9 2.7-3.8 775-997 1705-2193 J250/BOCEPin On General Purpose 2550 100 1.8-2.5 2.5-3.2 812-979 1786-2154 J250/BOCE
Sand and Gravel 2750 108 2.6-3.2 3.4-4.1 1026-1147 2262-2523 J250/BOCELight Material 2750 108 3.1-5.0 4.0-6.5 1096-1383 2416-3043 BOCEHigh Dump 2550-3060 100-120 3.0-3.5 4.0-6.5 1695-2149 3737-4738 BOCE
938K Fusion General Purpose 2550-2750 100-108 2.5-2.9 3.2-3.8 961-1042 2118-2292 J250/BOCELight Material 2750 108 3.1-5.0 4.0-6.5 1075-1360 2370-2992 BOCEMulti-Purpose 2550 100 2.1 2.7 1288 2834 J250/BOCESide Dump 3105 122 1.9 2.5 1653 3644 BOCEHigh Dump 3060 120 4.1-5.0 5.4-6.5 2041-2123 4500-4680 BOCEGrapple 2697 106 2.7-2.9 3.5-3.8 1632-1673 3598-3688 J250/BOCEWaste 3059 120 3.6-4.0 4.7-5.2 1416-1547 3122-3410 BOCEWoodchip 3330 131 4.9-5.5 6.4-7.2 1717-1795 3785-3957 BOCEGrading 2700 106 1.9 2.5 1233 2716 BOCE
ISO General Purpose 2550-2750 100-108 2.1-2.9 2.7-3.8 775-997 1705-2193 J250/BOCEPin On General Purpose 2550-2750 100-108 2.4-2.8 3.2-3.8 968-1059 2134-2330 J250/BOCE
Sand and Gravel 2750 108 2.7-3.2 3.5-4.1 1075-1146 2365-2521 J250/BOCELight Material 2750 108 3.5-5.0 4.5-6.5 1178-1378 2596-3038 BOCEHigh Dump 3060 120 4.1-5.0 5.4-6.5 2065-2147 4553-4733 BOCE
PHB-Sec23(pg175-290).indd 252PHB-Sec23(pg175-290).indd 252 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-253
Wheel LoadersIntegrated Toolcarriers
23
Buckets● Australia/New Zealand
Model Interface Bucket Type Width Capacity Weight GETmm in m3 yd3 kg lb
IT62G HPL Material Handling 2921 115 3.1 4.1 1242 2738 K80X8Material Handling 2921 115 3.2 4.2 1259 2776 K80X8Woodchip 3277 129 5.5 7.2 1493 3291 N/A
950H, 950G, 962H, 926G
Pin On General Purpose Performance Series 2894 114 3.1 4.1 1507 3322 K80X8
General Purpose Performance Series 2894 114 3.3 4.3 1550 3417 K80X8
Material Handling Performance Series 2894 114 3.2 4.2 1538 3391 K80X8
Material Handling Performance Series 2894 114 3.4 4.4 719 1585 K80X8
Material Handling Performance Series 2894 114 3.8 5.0 1684 3713 K80X8
General Purpose 2921 115 3.1 4.0 1483 3269 K80X8General Purpose 2921 115 3.4 4.5 1583 3490 K80X8Material Handling 2921 115 3.4 4.5 1424 3139 K80X8Material Handling 2946 116 4.2 5.5 1725 3803 K80X8Material Handling N/A N/A 3.3 4.3 1326 2923 K80X8Rock 2972 117 2.9 3.8 1550 3417 N/ARock 2972 117 2.9 3.8 1618 3567 N/AWoodchip 3327 131 9.2 12.0 2279 5024 N/A
HPL General Purpose 2921 115 3.1 4.1 1479 3261 K80X8General Purpose 2921 115 3.2 4.2 1280 2822 K80X8General Purpose 2921 115 3.4 4.4 1385 3053 K80X8Woodchip 3327 131 9.2 12.0 2349 5179 N/A
Fusion General Purpose 2896 114 3.1 4.1 1322 2915 K80X8General Purpose 2896 114 3.4 4.4 1408 3104 K80X8General Purpose 2896 114 3.8 5.0 1483 3269 K80X8Rock 2969 117 3.1 4.1 1588 3501 K90X8Rock 2969 117 3.3 4.3 1638 3611 K90X8Material Handling 2896 114 3.4 4.4 1370 3020 K80X8Material Handling 2896 114 3.8 5.0 1447 3190 K80X8Coal 3302 130 5.9 7.7 1928 4251 N/AMulti-purpose 2946 116 2.87 3.75 2087 4601 N/ASide Dump 3226 127 2.87 3.75 2340 5159 N/AHigh Dump 2921 115 4.6 6.0 2657 5858 N/AGrapple 2921 115 3.25 4.25 2139 4716 N/AWaste 3048 120 5.2 6.8 2163 4769 N/AWoodchip 3327 131 9.2 12.0 2121 4676 N/A
N/A = Not Applicable
PHB-Sec23(pg175-290).indd 253PHB-Sec23(pg175-290).indd 253 12/20/13 9:07 AM12/20/13 9:07 AM
23-254 Edition 44
Wheel LoadersIntegrated Toolcarriers
Buckets● Australia/New Zealand
Model Interface Bucket Type Width Capacity Weight GETmm in m3 yd3 kg lb
966, 972
Pin On General Purpose Performance Series 3193 126 4.0 5.2 2164 4771 K90X8
General Purpose Performance Series 3193 126 4.2 5.5 2220 4894 K90X8
General Purpose Performance Series 3193 126 4.6 6.0 2220 4894 K90X8
General Purpose Performance Series 3193 126 4.6 6.0 2303 5077 K90X8
General Purpose Performance Series 3201 126 5.0 6.5 2332 5141 K90X8
Material Handling Performance Series 3302 130 4.0 5.2 2173 4791 K90X8
Material Handling Performance Series 3193 126 4.2 5.5 2108 4647 K90X8
Material Handling Performance Series 3193 126 4.6 6.0 2152 4744 K90X8
Rock Performance Series 3255 128 3.4 4.4 2362 5207 K90X8Rock Performance Series 3255 128 4.0 5.2 2397 5284 K90X8General Purpose 3150 124 4.0 5.2 1992 4392 K90X8General Purpose 3226 127 5.2 6.8 2141 4720 N/AMaterial Handling 3302 130 4.0 5.2 2049 4517 K90Material Handling 3311 130 4.7 6.1 2207 4866 K90Material Handling 3200 126 4.9 6.4 2130 4696 N/AMaterial Handling 3193 126 4.3 5.6 2108 4647 N/ARock 3252 128 N/A N/A 2405 5302 K90X8Rock 3252 128 N/A N/A 2522 5560 J350X8Rock 3252 128 N/A N/A 2522 5560 K90X8Heavy Duty Rock 3251 128 3.6 4.7 2425 5346 J350Heavy Duty Rock 3252 128 3.6 4.7 2562 5648 K90Heavy Duty Rock 3251 128 4.0 5.2 2949 6501 K90Woodchip 3327 131 8.0 10.46 2474 5454 N/AWoodchip 3937 155 9.9 13.0 2359 5201 N/AWoodchip 3923 154 10.2 13.3 2279 5024 N/A
HPL General Purpose 3023 119 3.8 5.0 1093 2410 K90X8General Purpose 3226 127 4.2 5.5 1986 4378 K90X8General Purpose 3226 127 4.6 6.0 1900 4189 K90X8Woodchip 3328 131 8.0 10.46 2360 5203 N/AWoodchip 3937 155 9.9 13.0 2825 6228 N/A
N/A = Not Applicable
PHB-Sec23(pg175-290).indd 254PHB-Sec23(pg175-290).indd 254 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-255
Wheel LoadersIntegrated Toolcarriers
23
Buckets● Australia/New Zealand
Model Interface Bucket Type Width Capacity Weight GETmm in m3 yd3 kg lb
966, 972
Fusion General Purpose 3307 130 3.8 5.0 1730 3814 K90X8General Purpose 3307 130 4.2 5.5 1808 3986 K90X8General Purpose 3311 130 4.8 6.3 1914 4220 K90X8Rock/Spade 3252 128 N/A N/A 2174 4793 K90X8Rock/Spade 3252 128 N/A N/A 2050 4519 K90X8Material Handling 3311 130 4.2 5.5 1850 4079 K90X8Material Handling 3311 130 4.6 6.0 1882 4149 K90X8Coal 3405 134 6.7 8.8 2271 5007 K90X8Coal 3405 134 7.7 10.1 2454 5410 K90X8Multi-purpose 3220 127 N/A N/A 2785 6140 N/ASide Dump 3677 145 N/A N/A 2832 6243 N/AHigh Dump 3059 120 N/A N/A 2862 6310 N/AGrapple 3048 120 N/A N/A 4380 9656 N/AWaste 3323 131 N/A N/A 2569 5664 N/AWoodchip 3923 154 9.94 13 2543 5606 N/A
980H, 980G
Pin On General Purpose Performance Series 3405 134 5.3 6.9 2572 5670 K100X8
General Purpose Performance Series 3405 134 5.7 7.5 2677 5902 K100X8
General Purpose Performance Series 3405 134 7.0 9.2 2726 6010 K100X8
Material Handling Performance Series 3405 134 5.7 7.5 2780 6129 K100X8
Rock Performance Series 3510 138 N/A N/A 3402 7500 K100X8Rock Performance Series 3510 138 N/A N/A 3531 7785 K100X8General Purpose 3531 139 4.8 6.3 2340 5159 K100X8General Purpose 3531 139 5.2 6.8 2430 5357 K100X8General Purpose 3531 139 5.5 7.2 2503 5518 K100X8General Purpose 3413 134 N/A N/A 2580 5688 K100X8General Purpose 3531 139 5.2 6.8 2398 5287 K100X8General Purpose 3531 139 5.5 7.2 2654 5851 K100X8General Purpose-HD 3533 139 5.5 7.2 3167 6982 K100X8Material Handling 3531 139 5.7 7.5 2727 6012 K100X8Material Handling 3683 145 7.5 9.7 3512 7743 K100X8Rock 3480 137 N/A N/A 2576 5679 J400X8Rock 3492 137 N/A N/A 2754 6072 K100X8Rock 3492 137 N/A N/A 3084 6799 J400X8Rock 3492 137 N/A N/A 3132 6905 K100X8Coal 3638 143 N/A N/A 3622 7985 N/AWoodchip 4165 164 N/A N/A 3996 8810 N/A
Pin On Coal 3800 150 6.5 8.5 4511 9945 K110Coal 4120 162 11.5 15.0 5910 13,029 BOCE IncludedCoal 4120 162 13.0 17.0 6325 13,944 BOCE IncludedGeneral Purpose 2695 106 7.0 9.2 4218 9299 K110General Purpose 3900 154 7.7 10.1 4770 10,516 BOCE IncludedRock 3835 151 6.4 8.4 4815 10,615 K130Rock 4026 159 6.9 9.0 4662 10,278 K110Rock 4026 159 7.7 10.1 4600 10,141 K110
N/A = Not Applicable
PHB-Sec23(pg175-290).indd 255PHB-Sec23(pg175-290).indd 255 12/20/13 9:07 AM12/20/13 9:07 AM
23-256 Edition 44
Wheel LoadersIntegrated Toolcarriers
Model Interface Bucket Type Width Capacity Weight GETmm in m3 yd3 kg lb
990H Pin On Rock 4450 175 8.5 11.1 6772 14,930 K130Rock 4597 181 9.2 12.0 7038 15,516 K130Heavy Duty Rock 4510 178 8.5 11.1 8594 18,947 K130 MAWPsHeavy Duty Granite 4620 182 8.5 11.1 9929 21,890 K150 MAWPsSlag 4450 175 9.2 12.0 9613 21,193 SerratedSlag 4500 177 8.5 11.1 9149 20,170 K130Coal 4370 172 13.4 17.5 7460 16,446 BOCE IncludedSlag 4450 175 7.0 9.2 8525 18,794 K150Serrated Edge Rock 4610 181 9.5 12.4 8140 17,946 N/A
992K Pin On Rock 4824 190 10.7 14.0 9382 20,684 K150Rock 4884 192 11.5 15.0 9776 21,552 K170Rock 4824 190 11.5 15.0 9557 21,070 K150Rock 4824 190 12.2 16.0 10 574 23,312 K170Heavy Duty Rock 5068 200 10.7 14.0 11 560 25,485 K170High Abrasion Rock 5068 200 10.7 14.0 11 927 26,295 K150Heavy Duty Granite 5165 203 10.7 14.0 13 720 30,247 K150Coal 6170 243 19.0 24.9 12 504 27,567 BOCE IncludedIron Ore 4900 193 9.0 11.8 11 172 24,630 K150Serrated Edge Rock 4824 190 12.3 16.1 10 282 22,668 N/A
992G Pin On Coal 6200 244 23.0 30.0 11 679 25,694 K130Rock 4824 190 12.2 16.0 9783 21,522 K150Rock 6200 244 23.0 30.1 N/A N/A K130Rock 4840 191 11.5 15.0 N/A N/A K150Rock 4824 190 11.5 15.0 9451 20,836 K150Rock 4824 190 12.2 16.0 9704 21,394 K170Rock 5060 199 11.4 14.9 11 674 25,737 K170Heavy Duty Granite 5060 199 11.5 15.0 13 390 29,520 K150
993K Pin On Rock 5068 200 12.2 16.0 12 864 28,360 K170Rock 5068 200 13.0 17.0 13 380 29,498 K170Rock 5068 200 13.8 18.0 14 024 30,918 K170Rock 5068 200 14.5 19.0 14 209 31,325 K170High Abrasion Rock 5160 203 12.2 16.0 15 205 33,521 K170High Abrasion Rock 5160 203 13.0 17.0 15 456 34,075 K170Heavy Duty Granite 5160 203 13.0 17.0 17 418 38,400 K170Coal 6300 248 23.0 30.1 17 673 38,962 K170Iron Ore 5160 203 10.0 13.1 14 063 31,004 K170Serrated Edge Rock 5080 200 15.0 19.6 13 915 30,677 N/A
994F Pin On Rock 5650 222 14.9 19.5 19 302 42,554 J800Rock 5650 222 17.2 22.5 19 525 43,045 J800Rock 5650 222 19.1 25.0 21 282 46,919 J800Rock 6220 245 18.0 23.5 21 427 47,238 J800Rock 6220 245 19.1 25.0 21 777 48,010 J800Coal 6220 245 31.3 40.9 22 211 48,967 J700Coal 6300 248 35.9 47.0 23 598 52,025 Serrated
N/A = Not Applicable
Buckets● Australia/New Zealand
PHB-Sec23(pg175-290).indd 256PHB-Sec23(pg175-290).indd 256 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-257
Wheel LoadersIntegrated Toolcarriers
23
Buckets● Southeast Asia
Model Interface Bucket Type Width Capacity Weight GETmm in m3 yd3 kg lb
IT62G HPL Material Handling 2921 115 3.20 4.2 1259 571 K80X8Woodchip 3277 129 8.40 11.0 1493 677 N/A
950H, 950G, 962H, 962G
Pin On General Purpose 2894 114 3.10 4.1 1507 684 K80X8General Purpose 2894 114 3.30 4.3 1550 703 K80X8Material Handling 2894 114 3.20 4.2 1538 698 K80X8Material Handling 2894 114 3.40 4.4 1584 719 K80X8Material Handling 2894 114 3.80 5.0 1684 764 K80X8General Purpose 2997 118 2.70 3.5 1347 611 K80X8General Purpose 2921 115 3.06 4.0 1483 673 K80X8Material Handling 2946 116 5.73 7.5 1878 852 N/AMaterial Handling 2946 116 4.40 5.8 1905 864 N/AMaterial Handling N/A N/A 3.30 4.3 1326 601 K80X8Waste Handling 3058 120 5.20 6.8 2375 1077 N/A
HPL Woodchip 3327 131 9.20 12.0 2349 1066 N/A966, 972
Pin On General Purpose 3193 126 4.00 5.2 2164 982 K90X8General Purpose 3193 126 4.20 5.5 2220 1007 K90X8General Purpose 3193 126 4.60 6.0 2220 1007 K90X8General Purpose 3193 126 4.60 6.0 2303 1045 K90X8General Purpose 3201 126 5.00 6.5 2332 1058 K90X8Material Handling 3302 130 4.00 5.2 2173 986 K90X8Material Handling 3193 126 4.20 5.5 2108 956 K90X8Material Handling 3193 126 4.60 6.0 2152 976 K90X8Rock 3255 128 3.40 4.4 2362 1071 K90X8Rock 3255 128 4.00 5.2 2397 1087 K90X8General Purpose 3150 124 3.80 5.0 2188 992 K90X8General Purpose 3150 124 3.60 4.7 1903 863 K90X8General Purpose 3150 124 4.00 5.2 1992 904 K90X8Material Handling 3454 136 5.73 7.5 2586 1173 N/AMaterial Handling 3429 135 7.26 9.5 2595 1177 N/ARock 3252 128 N/A N/A 2405 1091 K90X8Woodchip 3937 155 9.90 12.9 2359 1070 N/A
HPL General Purpose 3023 119 3.82 5.0 1093 496 K90X8General Purpose 3226 127 4.21 5.5 1986 901 K90X8
N/A = Not Applicable
PHB-Sec23(pg175-290).indd 257PHB-Sec23(pg175-290).indd 257 12/20/13 9:07 AM12/20/13 9:07 AM
23-258 Edition 44
Wheel LoadersIntegrated Toolcarriers
Buckets● Southeast Asia
Model Interface Bucket Type Width Capacity Weight GETmm in m3 yd3 kg lb
980H, 980G
Pin On General Purpose 3405 134 5.30 6.9 2572 1167 K100X8General Purpose 3405 134 5.70 7.5 2677 1214 K100X8General Purpose 3405 134 7.00 9.2 2726 1237 K100X8Material Handling 3405 134 5.70 7.5 2780 1261 K100X8Rock 3510 138 N/A N/A 3402 1543 K100X8Rock 3510 138 N/A N/A 3531 1602 K100X8General Purpose 3531 139 5.40 7.1 2430 1102 K100X8General Purpose 3531 139 5.70 7.5 2503 1135 K100X8Rock 3492 137 N/A N/A 3084 1399 J400X8Coal 3638 143 N/A N/A 3622 1643 N/A
HPL General Purpose 3454 136 5.00 6.5 2794 1267 K100X8BH Block Handler 3658 144 4.50 5.9 3810 1728 K100X8
988H, 988G
Pin On Coal 3800 150 6.50 8.5 4511 2046 K110Coal 4120 162 11.50 15.0 5910 2681 BOCE IncludedCoal 4120 162 13.00 17.0 6325 2869 BOCE IncludedRock 4026 159 6.90 9.0 4662 2115 K110Rock 4026 159 7.70 10.1 4600 2087 K110
990H Pin On Rock 4450 175 8.50 11.1 6772 3072 K130Rock 4597 181 9.20 12.0 7038 3192 K130Heavy Duty Granite 4620 182 8.50 11.1 9929 4504 K150 MAWPsSlag 4450 175 9.20 12.0 9613 4360 Serrated
Weld-On EdgeSlag 4500 177 8.50 11.1 9149 4150 K130
992K Pin On Rock 4824 190 10.70 14.0 9382 4256 K150Rock 4884 192 11.50 15.0 9776 4434 K170Rock 4824 190 11.50 15.0 9557 4335 K150Rock 4824 190 12.20 16.0 10 574 4796 K170Heavy Duty Rock 5068 200 10.70 14.0 11 560 5244 K170High Abrasion Rock 5068 200 10.70 14.0 11 927 5410 K150Heavy Duty Granite 5165 203 10.70 14.0 13 720 6223 K150Serrated Edge Rock 4824 190 12.30 16.1 10 282 4664 N/A
992G Pin On Rock 6200 244 23.00 30.1 N/A N/A K130Rock 4840 191 11.50 15.0 N/A N/A K150Rock 4824 190 11.50 15.0 9451 4287 K150Rock 5060 199 11.40 14.9 11 674 5295 K170Heavy Duty Granite 5060 199 11.50 15.0 13 390 6074 K150
993K Pin On Rock 5068 200 12.20 16.0 12 864 5835 K170Rock 5068 200 14.50 19.0 14 209 6445 K170High Abrasion Rock 5160 203 13.00 17.0 15 456 7011 K170Heavy Duty Granite 5160 203 13.00 17.0 17 418 7901 K170Coal 6300 248 23.00 30.1 17 673 8016 K170Iron Ore 5160 203 10.00 13.1 14 063 6379 K170
994F Pin On Rock 5650 222 14.90 19.5 19 302 8755 J800Rock 5650 222 17.20 22.5 19 525 8857 J800Rock 5639 222 14.00 18.3 18 310 8305 J800Coal 6220 245 31.30 40.9 22 211 10,075 J700Coal 6300 248 35.90 47.0 23 598 10,704 Serrated
Weld-On Edge N/A = Not Applicable
PHB-Sec23(pg175-290).indd 258PHB-Sec23(pg175-290).indd 258 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-259
Wheel LoadersIntegrated Toolcarriers
23
Buckets● China
Model Interface Bucket Type Width Capacity Weight GETmm in m3 yd3 kg lb
IT62G IT Woodchip 3277 129 8.40 10.99 1493 3291 N/A950H, 950G, 962H, 962G
Pin On General Purpose Performance Series 2894 114 3.10 4.05 1507 3322 K80X8
General Purpose Performance Series 2894 114 3.30 4.32 1550 3417 K80X8
Material Handling Performance Series 2894 114 3.20 4.19 1538 3391 K80X8
Material Handling Performance Series 2894 114 3.40 4.45 1584 3492 K80X8
Material Handling Performance Series 2894 114 3.80 4.97 1684 3713 K80X8
General Purpose 2997 118 2.70 3.53 1347 2970 K80X8General Purpose 2921 115 3.06 4.00 1483 3269 K80X8Material Handling 2946 116 5.73 7.49 1878 4140 N/AMaterial Handling 2946 116 4.40 5.75 1905 4200 N/AMaterial Handling N/A 3.30 4.32 1326 2923 K80X8Waste Handling 3058 120 5.20 6.80 2375 5236 N/ARock 2972 117 2.90 3.79 1826 4026 J350X8
966G, 972G
General Purpose Performance Series 3193 126 4.00 5.23 2164 4771 K90X8
General Purpose Performance Series 3193 126 4.20 5.49 2220 4894 K90X8
General Purpose Performance Series 3193 126 4.60 6.02 2220 4894 K90X8
General Purpose Performance Series 3193 126 4.60 6.02 2303 5077 K90X8
General Purpose Performance Series 3201 126 5.00 6.54 2332 5141 K90X8
Material Handling Performance Series 3302 130 4.00 5.23 2173 4791 K90X8
Material Handling Performance Series 3193 126 4.20 5.49 2108 4647 K90X8
Material Handling Performance Series 3193 126 4.60 6.02 2152 4744 K90X8
Rock Performance Series 3255 128 3.40 4.45 2362 5207 K90X8Rock Performance Series 3255 128 4.00 5.23 2397 5284 K90X8General Purpose 3193 126 4.96 6.49 2125 4685 K90X8General Purpose 3150 124 3.60 4.71 1903 4195 K90X8General Purpose 3150 124 4.00 5.23 1992 4392 K90X8Material Handling 3302 130 4.00 5.23 2049 4517 K90X8Material Handling 3311 130 4.70 6.15 2207 4866 K90X8Material Handling 3447 136 5.73 7.49 2426 5348 N/ARock 3252 128 — — 2405 5302 K90X8Side Dump 3299 130 3.40 4.45 3855 8499 K80X8
N/A = Not Applicable
PHB-Sec23(pg175-290).indd 259PHB-Sec23(pg175-290).indd 259 12/20/13 9:07 AM12/20/13 9:07 AM
23-260 Edition 44
Wheel LoadersIntegrated Toolcarriers
Buckets● China
Model Interface Bucket Type Width CapacityWeightRange GET
mm in m3 yd3 kg lb980H, 980G
Pin On General Purpose Performance Series
3405 134 5.30 6.93 2572 5670 K100X8
General Purpose Performance Series
3405 134 5.70 7.46 2677 5902 K100X8
General Purpose Performance Series
3405 134 7.00 9.16 2726 6010 K100X8
Material Handling Performance Series
3405 134 5.70 7.46 2780 6129 K100X8
Rock Performance Series 3510 138 5.40 7.10 3402 7500 K100X8Rock Performance Series 3510 138 5.40 7.10 3531 7785 K100X8General Purpose 3531 139 5.40 7.06 2430 5357 K100X8
HPL Block Handler 3658 144 4.50 5.89 3810 8400 K100X8986H Pin On Rock 3772 148.5 5.4-6.1 7-8 3692-3907 8139-8693 J460988H, 988G
Pin On Coal 3800 150 6.50 8.50 4511 9945 K110Coal 4120 162 11.50 15.04 5910 13,029 BOCE IncludedCoal 4120 162 13.00 17.00 6325 13,944 BOCE IncludedGeneral Purpose 3900 154 7.70 10.07 4770 10,516 BOCE IncludedRock 3835 151 6.40 8.37 4815 10,615 K130Rock 4026 159 6.90 9.02 4662 10,278 K110Rock 4026 159 7.70 10.07 4600 10,141 K110
990H Pin On Rock 4450 175 8.50 11.12 6772 14,930 K130Rock 4597 181 9.20 12.03 7038 15,516 K130Heavy Duty Rock 4510 178 8.50 11.12 8594 18,947 K130 MAWPsHeavy Duty Granite 4620 182 8.50 11.12 9929 21,890 K150 MAWPsSlag 4450 175 9.20 12.03 9613 21,193 Serrated
Weld-On EdgeSlag 4500 177 8.50 11.12 9149 20,170 K130
992K Pin On Rock 4824 190 10.70 14.00 9382 20,684 K150Rock 4884 192 11.50 15.04 9776 21,552 K170Rock 4824 190 11.50 15.04 9557 21,070 K150Rock 4824 190 12.20 15.96 10 574 23,312 K170Heavy Duty Rock 5068 200 10.70 14.00 11 560 25,485 K170High Abrasion Rock 5068 200 10.70 14.00 11 927 26,295 K150Heavy Duty Granite 5165 203 10.70 14.00 13 720 30,247 K150Serrated Edge Rock 4824 190 12.30 16.09 10 282 22,668 N/A
992G Pin On Rock 6200 244 23.00 30.08 N/A N/A K130Rock 4840 191 11.50 15.04 N/A N/A K150Rock 4824 190 11.50 15.04 9451 20,836 K150Rock 5060 199 11.40 14.91 11 674 25,737 K170Heavy Duty Granite 5060 199 11.50 15.04 13 390 29,520 K150
993K Pin On Rock 5068 200 12.20 15.96 12 864 28,360 K170Rock 5068 200 14.50 18.97 14 209 31,325 K170High Abrasion Rock 5160 203 13.00 17.00 15 456 34,075 K170Heavy Duty Granite 5160 203 13.00 17.00 17 418 38,400 K170Coal 6300 248 23.00 30.08 17 673 38,962 K170Iron Ore 5160 203 10.00 13.08 14 063 31,004 K170
994F Pin On Rock 5650 222 17.20 22.50 19 525 43,045 J800Rock 5639 222 14.00 18.31 18 310 40,367 J800Coal 6220 245 31.30 40.94 22 211 48,967 J700Coal 6300 248 35.90 46.96 23 598 52,025 Serrated
Weld-On EdgeN/A = Not Applicable
PHB-Sec23(pg175-290).indd 260PHB-Sec23(pg175-290).indd 260 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-261
Wheel LoadersIntegrated Toolcarriers
23
Bucket Selection● 906H2–914G2
906H2Vertical Coupler
Bucket Type Rated CapacityMaximum
Material Density
m3 yd3 kg/m3 lb/yd3
General Purpose 0.90 1.18 1755 2952
Light Material 1.20 1.57 1208 2032
Multi-Purpose 0.75 0.98 2131 3584
906H2Horizontal Coupler
Bucket Type Rated CapacityMaximum
Material Density
m3 yd3 kg/m3 lb/yd3
General Purpose 0.90 1.18 1889 3177
Light Material 1.20 1.57 1271 2138
Multi-Purpose 0.75 0.98 2184 3674
907H2Vertical Coupler
Bucket Type Rated CapacityMaximum
Material Density
m3 yd3 kg/m3 lb/yd3
General Purpose 1.00 1.31 1584 2664
Light Material 1.20 1.57 1218 2049
Multi-Purpose 0.75 0.98 2149 3615
907H2Horizontal Coupler
Bucket Type Rated CapacityMaximum
Material Density
m3 yd3 kg/m3 lb/yd3
General Purpose 1.00 1.31 1706 2870
Light Material 1.20 1.57 1310 2203
Multi-Purpose 0.75 0.98 2202 3704
908H2Vertical Coupler
Bucket Type Rated CapacityMaximum
Material Density
m3 yd3 kg/m3 lb/yd3
General Purpose 1.10 1.44 1549 2605
Light Material 1.50 1.96 1034 1739
Multi-Purpose 0.90 1.18 1929 3245
908H2Horizontal Coupler
Bucket Type Rated CapacityMaximum
Material Density
m3 yd3 kg/m3 lb/yd3
General Purpose 1.10 1.44 1658 2789
Light Material 1.50 1.96 1106 1860
Multi-Purpose 0.90 1.18 1967 3309
914G2
kg/m3
lb/yd3
m3yd3
BU
CK
ET
CA
PAC
ITY
KEY
A — 1.4 m3 (1.8 yd3) General Purpose Bucket, bolt-on edge 1.4 m3 (1.8 yd3) General Purpose Bucket, bolt-on teeth and segments
B — 1.3 m3 (1.7 yd3) General Purpose Bucket, bolt-on edge1.3 m3 (1.7 yd3) General Purpose Bucket, bolt-on teeth and segments1.3 m3 (1.7 yd3) General Bucket, bolt-on teeth1.3 m3 (1.7 yd3) General Purpose Bucket, flush mounted teeth
C — 1.2 m3 (1.6 yd3) General Purpose Bucket, bolt-on teeth
MATERIAL DENSITY (THOUSANDS)
PHB-Sec23(pg175-290).indd 261PHB-Sec23(pg175-290).indd 261 12/20/13 9:07 AM12/20/13 9:07 AM
23-262 Edition 44
Wheel LoadersIntegrated Toolcarriers
Bucket Selection● 924K
MATERIAL DENSITY
924K Pin On
BU
CK
ET
CA
PAC
ITY
lb/yd3
kg/m3Bucket
Size
m3yd3
KEY
A — Standard LiftB — High Lift
% = Bucket Fill Factor
115% 100% 95%
MATERIAL DENSITY
924K Fusion
BU
CK
ET
CA
PAC
ITY
lb/yd3
kg/m3
BucketSize
m3yd3
PHB-Sec23(pg175-290).indd 262PHB-Sec23(pg175-290).indd 262 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-263
Wheel LoadersIntegrated Toolcarriers
23
Bucket Selection● 930K
MATERIAL DENSITY
930K Pin On
BU
CK
ET
CA
PAC
ITY
lb/yd3
kg/m3Bucket
Size
m3yd3
KEY
A — Standard LiftB — High Lift
% = Bucket Fill Factor
115% 100% 95%
MATERIAL DENSITY
930K Fusion
BU
CK
ET
CA
PAC
ITY
lb/yd3
kg/m3
BucketSize
m3yd3
PHB-Sec23(pg175-290).indd 263PHB-Sec23(pg175-290).indd 263 12/20/13 9:07 AM12/20/13 9:07 AM
23-264 Edition 44
Wheel LoadersIntegrated Toolcarriers
Bucket Selection● 938K
MATERIAL DENSITY
938K Pin On
BU
CK
ET
CA
PAC
ITY
lb/yd3
kg/m3
BucketSize
m3yd3
KEY
A — Standard LiftB — High Lift
% = Bucket Fill Factor
115% 100% 95%
MATERIAL DENSITY
938K Fusion
BU
CK
ET
CA
PAC
ITY
lb/yd3
kg/m3
BucketSize
m3yd3
PHB-Sec23(pg175-290).indd 264PHB-Sec23(pg175-290).indd 264 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-265
Wheel LoadersIntegrated Toolcarriers
23
924K (LRC)
Bucket Fill Factorkg/m3 1450 1525 1600 1675 1750 1825 1900 1975 2050 2125 2200 2275 2350
lb/yd3 2443 2570 2696 2822 2949 3075 3202 3328 3454 3581 3707 3833 3960
m3 yd3
Gen
eral
Pu
rpo
se
Pin On
1.7 2.2 112% 108% 105% 101% 98%
1.9 2.5 112% 108% 103% 100% 96%
2.1 2.7 115% 110% 105% 101% 97%
Fusion
1.9 2.5 111% 107% 103% 99% 95%
2.1 2.7 114% 109% 104% 100% 96%
2.3 3.0 109% 103% 99% 94%
Bucket Fill Factorkg/m3 650 700 750 800 850 900 950 1000 1050 1100 1150 1200 1250lb/yd3 1095 1180 1264 1348 1432 1517 1601 1685 1769 1854 1938 2022 2106
m3 yd3
Lig
ht
Mat
eria
l Pin On3.5 4.6 114% 108% 103% 98%
4.2 5.5 110% 103% 97%
Fusion3.5 4.6 115% 109% 103% 98%
4.2 5.5 112% 105% 98%
Material density and fill factor are key variables when choosing the appropriate size of the bucket. The long floor and open throat design of the Performance Series Buckets along with the aggressive rack angles of the optimized K Series linkage will demonstrate fill factors greater than 100% ISO rated. Refer to the Fill Factors table for expected fill factor per material density and Bucket Selection table for bucket sizing.
924K (LRC) Fill Factors
Materials Density Fill %
Earth and rock ~ 1800 kg/m3 ~ 3033 lb/yd3 ~ 115%
Sand and gravel ~ 1700 kg/m3 ~ 2865 lb/yd3 ~ 115%
Aggregates ~ 1600 kg/m3 ~ 2696 lb/yd3 ~ 105%
Bulk grains ~ 750 kg/m3 ~ 1264 lb/yd3 ~ 100%
Woodchips ~ 500 kg/m3 ~ 843 lb/yd3 ~ 100%
Bucket Selection● 924K (LRC)
PHB-Sec23(pg175-290).indd 265PHB-Sec23(pg175-290).indd 265 12/20/13 9:07 AM12/20/13 9:07 AM
23-266 Edition 44
Wheel LoadersIntegrated Toolcarriers
Bucket Selection● 930K (LRC)
930K (LRC)
Bucket Fill Factorkg/m3 1375 1450 1525 1600 1675 1750 1825 1900 1975 2050 2125
High Liftlb/yd3 2317 2443 2570 2696 2822 2949 3075 3202 3328 3454 3581
m3 yd3 kg/m3 lb/yd3
Gen
eral
Pu
rpo
se
Pin On
2.1 2.7 111% 106% 102% 98% 95% –573 –965
2.3 3.0 114% 109% 104% 100% 96% –519 –874
2.5 3.3 114% 108% 103% 98% 94% –474 –799
Fusion
2.1 2.7 115% 110% 105% 101% 97% –564 –951
2.3 3.0 114% 109% 104% 99% 95% –511 –862
2.5 3.3 115% 109% 104% 99% 94% –467 –787
Bucket Fill Factorkg/m3 650 700 750 800 850 900 950 1000 1050 1100 1150
High Liftlb/yd3 1095 1180 1264 1348 1432 1517 1601 1685 1769 1854 1938
m3 yd3 kg/m3 lb/yd3
Lig
ht
Mat
eria
l Pin On4.2 5.5 114% 108% 102% 96% –270 –455
5.0 6.5 109% 102% 96% –228 –384
Fusion4.2 5.5 109% 103% 97% –267 –450
5.0 6.5 112% 104% 97% –225 –379
Material density and fill factor are key variables when choosing the appropriate size of the bucket. The long floor and open throat design of the Performance Series Buckets along with the aggressive rack angles of the optimized K Series linkage will demonstrate fill factors greater than 100% ISO rated. Refer to the Fill Factors table for expected fill factor per material density and Bucket Selection table for bucket sizing.
930K (LRC) Fill Factors
Materials Density Fill %
Earth and rock ~ 1800 kg/m3 ~ 3033 lb/yd3 ~ 115%
Sand and gravel ~ 1700 kg/m3 ~ 2865 lb/yd3 ~ 115%
Aggregates ~ 1600 kg/m3 ~ 2696 lb/yd3 ~ 105%
Bulk grains ~ 750 kg/m3 ~ 1264 lb/yd3 ~ 100%
Woodchips ~ 500 kg/m3 ~ 843 lb/yd3 ~ 100%
PHB-Sec23(pg175-290).indd 266PHB-Sec23(pg175-290).indd 266 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-267
Bucket Selection● 938K (LRC)
Wheel LoadersIntegrated Toolcarriers
938K (LRC)
Bucket Fill Factorkg/m3 1375 1450 1525 1600 1675 1750 1825 1900 1975 2050 2125
High Liftlb/yd3 2317 2443 2570 2696 2822 2949 3075 3202 3328 3454 3581
m3 yd3 kg/m3 lb/yd3
Gen
eral
Pu
rpo
se
Pin On
2.5 3.3 111% 106% 102% 98% 95% –516 –869
2.7 3.5 111% 106% 102% 98% –474 –799
2.9 3.8 113% 108% 103% 98% –439 –740
Fusion
2.5 3.3 110% 106% 101% 97% –506 –853
2.7 3.5 111% 106% 101% 97% –466 –784
2.9 3.8 114% 108% 103% 98% –431 –726
Bucket Fill Factorkg/m3 650 700 750 800 850 900 950 1000 1050 1100 1150
High Liftlb/yd3 1095 1180 1264 1348 1432 1517 1601 1685 1769 1854 1938
m3 yd3 kg/m3 lb/yd3
Lig
ht
Mat
eria
l Pin On4.2 5.5 114% 108% 103% 98% –293 –494
5.0 6.5 113% 107% 101% 95% –248 –417
Fusion4.2 5.5 114% 108% 103% 98% –288 –485
5.0 6.5 115% 108% 101% 96% –243 –410
Material density and fill factor are key variables when choosing the appropriate size of the bucket. The long floor and open throat design of the Performance Series Buckets along with the aggressive rack angles of the optimized K Series linkage will demonstrate fill factors greater than 100% ISO rated. Refer to the Fill Factors table for expected fill factor per material density and Bucket Selection table for bucket sizing.
938K (LRC) Fill Factors
Materials Density Fill %
Earth and rock ~ 1800 kg/m3 ~ 3033 lb/yd3 ~ 115%
Sand and gravel ~ 1700 kg/m3 ~ 2865 lb/yd3 ~ 115%
Aggregates ~ 1600 kg/m3 ~ 2696 lb/yd3 ~ 105%
Bulk grains ~ 750 kg/m3 ~ 1264 lb/yd3 ~ 100%
Woodchips ~ 500 kg/m3 ~ 843 lb/yd3 ~ 100%
PHB-Sec23(pg175-290).indd 267PHB-Sec23(pg175-290).indd 267 12/20/13 9:07 AM12/20/13 9:07 AM
23-268 Edition 44
Wheel LoadersIntegrated Toolcarriers
Bucket Selection● 950K
950K
800kg/m3
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
Material Density
GeneralPurpose
MaterialHandling
Stan
dard
Lin
kage
Pin
On
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
GeneralPurpose
MaterialHandling
Fusi
on Q
C
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors
NOTE: All buckets are showing Bolt-On Edges. Material Handling buckets are flat floor buckets.These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
2500
4213
PHB-Sec23(pg175-290).indd 268PHB-Sec23(pg175-290).indd 268 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-269
Bucket Selection● 950K
Wheel LoadersIntegrated Toolcarriers
950K
800kg/m3
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
Material Density
GeneralPurpose
MaterialHandling
Hig
h Li
ft Li
nkag
e
Pin
On
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
GeneralPurpose
MaterialHandling
Fusi
on Q
C
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors
NOTE: All buckets are showing Bolt-On Edges. Material Handling buckets are flat floor buckets.These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
2500
4213
PHB-Sec23(pg175-290).indd 269PHB-Sec23(pg175-290).indd 269 12/20/13 9:07 AM12/20/13 9:07 AM
23-270 Edition 44
Wheel LoadersIntegrated Toolcarriers
Bucket Selection● 950K
950K
800kg/m3
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
Material Density
GeneralPurpose
MaterialHandling
Pow
er P
acka
ge
Pin
On
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
GeneralPurpose
MaterialHandling
Fusi
on Q
C
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors
NOTE: All buckets are showing Bolt-On Edges. Material Handling buckets are flat floor buckets.These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
2500
4213
PHB-Sec23(pg175-290).indd 270PHB-Sec23(pg175-290).indd 270 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-271
Wheel LoadersIntegrated Toolcarriers
23
Bucket Selection● 962K
962K
800kg/m3
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
Material Density
GeneralPurpose
MaterialHandling
Stan
dard
Lin
kage
Pin
On
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
GeneralPurpose
MaterialHandling
Fusi
on Q
C
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors
NOTE: All buckets are showing Bolt-On Edges. Material Handling buckets are flat floor buckets.These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
2500
4213
PHB-Sec23(pg175-290).indd 271PHB-Sec23(pg175-290).indd 271 12/20/13 9:07 AM12/20/13 9:07 AM
23-272 Edition 44
Wheel LoadersIntegrated Toolcarriers
Bucket Selection● 962K
962K
800kg/m3
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
Material Density
GeneralPurpose
MaterialHandling
Hig
h Li
ft Li
nkag
e
Pin
On
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
2.70 m3 (3.53 yd3) 3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
2.90 m3 (3.79 yd3) 3.34 m3 (4.37 yd3) 2.90 m3 (3.79 yd3)
3.10 m3 (4.05 yd3) 3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.30 m3 (4.32 yd3) 3.80 m3 (4.97 yd3) 3.30 m3 (4.32 yd3)
3.40 m3 (4.45 yd3) 3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3) 4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
GeneralPurpose
MaterialHandling
Fusi
on Q
C
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors
NOTE: All buckets are showing Bolt-On Edges. Material Handling buckets are flat floor buckets.These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
2500
4213
PHB-Sec23(pg175-290).indd 272PHB-Sec23(pg175-290).indd 272 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-273
Wheel LoadersIntegrated Toolcarriers
23
Bucket Selection● 966M
966M
800kg/m3
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
4.60 m3 (6.02 yd3) 4.00 m3 (5.23 yd3)
4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
5.06 m3 (6.62 yd3) 4.40 m3 (5.75 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
4.00 m3 (5.23 yd3)
4.20 m3 (5.49 yd3)
4.20 m3 (5.49 yd3)
4.40 m3 (5.75 yd3)
4.60 m3 (6.02 yd3)
4.20 m3 (5.49 yd3)
4.60 m3 (6.02 yd3)
4.20 m3 (5.49 yd3)
Material Density
GeneralPurpose
MaterialHandling/Standard
MaterialHandling/
Heavy Duty
GeneralPurpose
Stan
dard
Lin
kage
Pin
On
Hoo
k O
n
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
NOTE: All buckets are showing Bolt-On Edges.These machines meet U.S. EPA Tier 4 Final/EU Stage IV emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
PHB-Sec23(pg175-290).indd 273PHB-Sec23(pg175-290).indd 273 12/20/13 9:07 AM12/20/13 9:07 AM
23-274 Edition 44
Wheel LoadersIntegrated Toolcarriers
Bucket Selection● 966K
966K
800kg/m3
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
4.60 m3 (6.02 yd3) 4.00 m3 (5.23 yd3)
4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
8.17 m3 (10.69 yd3) 7.10 m3 (9.29 yd3)
4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
8.17 m3 (10.69 yd3) 7.10 m3 (9.29 yd3)
4.00 m3 (5.23 yd3)
4.20 m3 (5.49 yd3)
4.60 m3 (6.02 yd3)
4.20 m3 (5.49 yd3)
3.40 m3 (4.45 yd3)
7.10 m3 (9.29 yd3)
3.80 m3 (4.97 yd3)
4.20 m3 (5.49 yd3)
4.60 m3 (6.02 yd3)
7.10 m3 (9.29 yd3)
Material Density
GeneralPurpose
MaterialHandling
Rock
Coal
GeneralPurpose
Coal
Stan
dard
Lin
kage
Pin
On
Fusi
on Q
C
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
2500
4213
NOTE: All buckets are showing Bolt-On Edges. Material Handling buckets are flat floor buckets.These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
PHB-Sec23(pg175-290).indd 274PHB-Sec23(pg175-290).indd 274 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-275
Wheel LoadersIntegrated Toolcarriers
23
Bucket Selection● 966K
966K
800kg/m3
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
4.60 m3 (6.02 yd3) 4.00 m3 (5.23 yd3)
4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
8.17 m3 (10.69 yd3) 7.10 m3 (9.29 yd3)
4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
8.17 m3 (10.69 yd3) 7.10 m3 (9.29 yd3)
4.00 m3 (5.23 yd3)
4.20 m3 (5.49 yd3)
4.60 m3 (6.02 yd3)
4.20 m3 (5.49 yd3)
3.40 m3 (4.45 yd3)
7.10 m3 (9.29 yd3)
3.80 m3 (4.97 yd3)
4.20 m3 (5.49 yd3)
4.60 m3 (6.02 yd3)
7.10 m3 (9.29 yd3)
Material Density
GeneralPurpose
MaterialHandling
Rock
Coal
GeneralPurpose
Coal
Hig
h Li
ft Li
nkag
e
Pin
On
Fusi
on Q
C
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
2500
4213
NOTE: All buckets are showing Bolt-On Edges. Material Handling buckets are flat floor buckets.These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availabilit
PHB-Sec23(pg175-290).indd 275PHB-Sec23(pg175-290).indd 275 12/20/13 9:07 AM12/20/13 9:07 AM
23-276 Edition 44
Wheel LoadersIntegrated Toolcarriers
Bucket Selection● 972M
972M
800kg/m3
4.20 m3 (5.49 yd3) 4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
5.52 m3 (7.22 yd3) 4.80 m3 (6.28 yd3)
5.75 m3 (7.52 yd3) 5.00 m3 (6.54 yd3)
5.52 m3 (7.22 yd3) 4.80 m3 (6.28 yd3)
5.75 m3 (7.52 yd3) 5.00 m3 (6.54 yd3)
5.75 m3 (7.52 yd3) 5.00 m3 (6.54 yd3)
5.98 m3 (7.82 yd3) 5.20 m3 (6.80 yd3)
4.60 m3 (5.75 yd3)
4.80 m3 (6.28 yd3)
5.00 m3 (6.54 yd3)
4.80 m3 (6.28 yd3)
5.00 m3 (6.54 yd3)
5.00 m3 (6.54 yd3)
5.20 m3 (6.80 yd3)
Material Density
GeneralPurpose
MaterialHandling/Standard
MaterialHandling/
Heavy Duty
Stan
dard
Lin
kage
Pin
On
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
NOTE: All buckets are showing Bolt-On Edges.These machines meet U.S. EPA Tier 4 Final/EU Stage IV emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
PHB-Sec23(pg175-290).indd 276PHB-Sec23(pg175-290).indd 276 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-277
Wheel LoadersIntegrated Toolcarriers
23
Bucket Selection● 972K
972K
800kg/m3
4.20 m3 (5.49 yd3) 4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
5.06 m3 (6.62 yd3) 4.40 m3 (5.75 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
5.52 m3 (7.22 yd3) 4.80 m3 (6.28 yd3)
5.75 m3 (7.52 yd3) 5.00 m3 (6.54 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
4.14 m3 (5.42 yd3) 3.42 m3 (4.47 yd3)
4.60 m3 (6.02 yd3) 3.80 m3 (4.97 yd3)
8.17 m3 (10.69 yd3) 7.10 m3 (9.29 yd3)
4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
5.06 m3 (6.62 yd3) 4.40 m3 (5.75 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
5.52 m3 (7.22 yd3) 4.80 m3 (6.28 yd3)
5.75 m3 (7.52 yd3) 5.00 m3 (6.54 yd3)
4.14 m3 (5.42 yd3) 3.42 m3 (4.47 yd3)
8.17 m3 (10.69 yd3) 7.10 m3 (9.29 yd3)
4.40 m3 (5.75 yd3)
4.60 m3 (6.02 yd3)
4.80 m3 (6.28 yd3)
5.00 m3 (6.54 yd3)
4.60 m3 (6.02 yd3)
3.60 m3 (4.71 yd3)
4.00 m3 (5.23 yd3)
7.10 m3 (9.29 yd3)
4.20 m3 (5.49 yd3)
4.40 m3 (5.75 yd3)
4.60 m3 (6.02 yd3)
4.80 m3 (6.28 yd3)
5.00 m3 (6.54 yd3)
3.60 m3 (4.71 yd3)
7.10 m3 (9.29 yd3)
Material Density
GeneralPurpose
MaterialHandling
Rock
Coal
GeneralPurpose
Rock
Coal
Stan
dard
Lin
kage
Pin
On
Fusi
on Q
C
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
2500
4213
NOTE: All buckets are showing Bolt-On Edges. Material Handling buckets are flat floor buckets.These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
PHB-Sec23(pg175-290).indd 277PHB-Sec23(pg175-290).indd 277 12/20/13 9:07 AM12/20/13 9:07 AM
23-278 Edition 44
Wheel LoadersIntegrated Toolcarriers
Bucket Selection● 972K
972K
800kg/m3
4.20 m3 (5.49 yd3) 4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
5.06 m3 (6.62 yd3) 4.40 m3 (5.75 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
5.52 m3 (7.22 yd3) 4.80 m3 (6.28 yd3)
5.75 m3 (7.52 yd3) 5.00 m3 (6.54 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
4.14 m3 (5.42 yd3) 3.42 m3 (4.47 yd3)
4.60 m3 (6.02 yd3) 3.80 m3 (4.97 yd3)
8.17 m3 (10.69 yd3) 7.10 m3 (9.29 yd3)
4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
5.06 m3 (6.62 yd3) 4.40 m3 (5.75 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
5.52 m3 (7.22 yd3) 4.80 m3 (6.28 yd3)
5.75 m3 (7.52 yd3) 5.00 m3 (6.54 yd3)
4.14 m3 (5.42 yd3) 3.42 m3 (4.47 yd3)
8.17 m3 (10.69 yd3) 7.10 m3 (9.29 yd3)
4.40 m3 (5.75 yd3)
4.60 m3 (6.02 yd3)
4.80 m3 (6.28 yd3)
5.00 m3 (6.54 yd3)
4.60 m3 (6.02 yd3)
3.60 m3 (4.71 yd3)
4.00 m3 (5.23 yd3)
7.10 m3 (9.29 yd3)
4.20 m3 (5.49 yd3)
4.40 m3 (5.75 yd3)
4.60 m3 (6.02 yd3)
4.80 m3 (6.28 yd3)
5.00 m3 (6.54 yd3)
3.60 m3 (4.71 yd3)
7.10 m3 (9.29 yd3)
Material Density
GeneralPurpose
MaterialHandling
Rock
Coal
GeneralPurpose
Rock
Coal
Hig
h Li
ft Li
nkag
e
Pin
On
Fusi
on Q
C
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
2500
4213
800kg/m3
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
5.64 m3 (7.38 yd3) 4.90 m3 (6.41 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
5.64 m3 (7.38 yd3) 4.90 m3 (6.41 yd3)
4.60 m3 (6.02 yd3)
4.90 m3 (6.41 yd3)
4.60 m3 (6.02 yd3)
4.90 m3 (6.41 yd3)
Material Density
GeneralPurpose
GeneralPurpose
Exte
nded
Cap
acity
Lin
kage
Pin
On
Fusi
on Q
C
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
2500
4213
NOTE: All buckets are showing Bolt-On Edges. Material Handling buckets are flat floor buckets.These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
PHB-Sec23(pg175-290).indd 278PHB-Sec23(pg175-290).indd 278 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-279
Wheel LoadersIntegrated Toolcarriers
23
Bucket Selection● 980K
980K
800kg/m3
5.40 m3 (7.06 yd3) 6.21 m3 (8.12 yd3) 5.40 m3 (7.06 yd3)
5.06 m3 (6.62 yd3) 4.40 m3 (5.75 yd3)
9.43 m3 (12.33 yd3) 8.20 m3 (10.73 yd3)
4.40 m3 (5.75 yd3)
8.20 m3 (10.73 yd3)
Material Density
GeneralPurpose
Rock
Coal
Stan
dard
Lin
kage
Pin
On
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
2500
4213
800kg/m3
5.40 m3 (7.06 yd3) 6.21 m3 (8.12 yd3) 5.40 m3 (7.06 yd3)
5.06 m3 (6.62 yd3) 4.40 m3 (5.75 yd3)
9.43 m3 (12.33 yd3) 8.20 m3 (10.73 yd3)
4.40 m3 (5.75 yd3)
8.20 m3 (10.73 yd3)
Material Density
GeneralPurpose
Rock
Coal
Hig
h Li
ft Li
nkag
e
Pin
On
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
2500
4213
800kg/m3
6.56 m3 (8.58 yd3) 5.70 m3 (7.46 yd3)
6.90 m3 (9.02 yd3) 6.00 m3 (7.85 yd3)
5.70 m3 (7.46 yd3)
6.56 m3 (8.58 yd3) 5.70 m3 (7.46 yd3)5.70 m3 (7.46 yd3)
6.00 m3 (7.85 yd3)
Material Density
GeneralPurpose
MaterialHandling
Agg
rega
tePa
ckag
e Li
nkag
e
Pin
On
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
2500
4213
NOTE: All buckets are showing Bolt-On Edges. Material Handling buckets are flat floor buckets.These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
PHB-Sec23(pg175-290).indd 279PHB-Sec23(pg175-290).indd 279 12/20/13 9:07 AM12/20/13 9:07 AM
23-280 Edition 44
Wheel LoadersIntegrated Toolcarriers
Bucket Selection● 950 GC
950 GC
800kg/m3
3.10 m3 3.57 m3 3.10 m3
3.80 m3 3.30 m3
3.91 m3 3.40 m3
4.14 m3 3.60 m3
3.57 m3 3.10 m3
3.30 m3
3.40 m3
3.60 m3
3.10 m3
Material Density
Pin On
Hook On
Stan
dard
Lin
kage
Gen
eral
Pur
pose
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400700
Bucket Fill Factors115% 110% 105% 100% 95%
2500
NOTE: All buckets are showing Bolt-On Edges.
PHB-Sec23(pg175-290).indd 280PHB-Sec23(pg175-290).indd 280 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-281
Wheel LoadersIntegrated Toolcarriers
23
Bucket Selection● 950H
950H
800kg/m3 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1,348
700
1,180lb/yd3 1,517 1,685 1,854 2,022 2,191 2,359 2,528 2,696 2,865 3,033 3,202 3,370 3,539 3,707 3,876 4,044
2500
4,213
3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
2.70 m3 (3.53 yd3)
3.10 m3 (4.05 yd3)
Material Density
GeneralPurpose
MaterialHandling
MaterialHandling
GeneralPurpose
Stan
dard
Lin
kage
Hig
h LI
ft Li
nkag
e
Pin
On
Pin
On
Material Density
115% 110% 105% 100% 95%
3.40 m3 (4.45 yd3)
3.20 m3 (4.19 yd3)
3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3)
2.70 m3 (3.53 yd3)
3.10 m3 (4.05 yd3)
3.40 m3 (4.45 yd3)
3.20 m3 (4.19 yd3)
3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3)
Bucket Fill Factors
NOTE: All buckets are showing Bolt-On Edges.
3.68 m3 (4.81 yd3) 3.20 m3 (4.19 yd3)
3.11 m3 (4.07 yd3) 2.70 m3 (3.53 yd3)
3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.68 m3 (4.81 yd3) 3.20 m3 (4.19 yd3)
PHB-Sec23(pg175-290).indd 281PHB-Sec23(pg175-290).indd 281 12/20/13 9:07 AM12/20/13 9:07 AM
23-282 Edition 44
Wheel LoadersIntegrated Toolcarriers
962H
800kg/m3 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1,348
700
1,180lb/yd3 1,517 1,685 1,854 2,022 2,191 2,359 2,528 2,696 2,865 3,033 3,202 3,370 3,539 3,707 3,876 4,044
2500
4,213
3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.10 m3 (4.05 yd3)
3.40 m3 (4.45 yd3)
Material Density
GeneralPurpose
MaterialHandling
MaterialHandling
GeneralPurpose
Stan
dard
Lin
kage
Hig
h LI
ft Li
nkag
e
Pin
On
Pin
On
Material Density
115% 110% 105% 100% 95%
3.60 m3 (4.71 yd3)
3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3)
3.10 m3 (4.05 yd3)
3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3)
3.40 m3 (4.45 yd3)
3.60 m3 (4.71 yd3)
3.80 m3 (4.97 yd3)
Bucket Fill Factors
NOTE: All buckets are showing Bolt-On Edges.
3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
3.57 m3 (4.67 yd3) 3.10 m3 (4.05 yd3)
3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
4.14 m3 (5.41 yd3) 3.60 m3 (4.71 yd3)
3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
Bucket Selection● 962H
PHB-Sec23(pg175-290).indd 282PHB-Sec23(pg175-290).indd 282 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-283
Wheel LoadersIntegrated Toolcarriers
23
Bucket Selection● 966H
966H
800kg/m3
3.80 m3 (4.97 yd3) 4.37 m3 (5.72 yd3) 3.80 m3 (4.97 yd3)
4.60 m3 (6.02 yd3) 4.00 m3 (5.23 yd3)
4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
3.91 m3 (5.11 yd3) 3.40 m3 (4.45 yd3)
4.60 m3 (6.02 yd3) 4.00 m3 (5.23 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
4.00 m3 (5.23 yd3)
4.20 m3 (5.49 yd3)
4.60 m3 (6.02 yd3)
3.40 m3 (4.45 yd3)
4.00 m3 (5.23 yd3)
4.60 m3 (6.02 yd3)
Material Density
GeneralPurpose
Rock
MaterialHandling/Standard
Stan
dard
Lin
kage
Pin
On
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
NOTE: All buckets are showing Bolt-On Edges.
PHB-Sec23(pg175-290).indd 283PHB-Sec23(pg175-290).indd 283 12/20/13 9:07 AM12/20/13 9:07 AM
972H
800kg/m3
4.20 m3 (5.49 yd3) 4.83 m3 (6.32 yd3) 4.20 m3 (5.49 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
4.60 m3 (6.02 yd3) 4.00 m3 (5.23 yd3)
5.29 m3 (6.92 yd3) 4.60 m3 (6.02 yd3)
5.75 m3 (7.52 yd3) 5.00 m3 (6.54 yd3)
4.60 m3 (6.02 yd3)
4.60 m3 (6.02 yd3)
4.00 m3 (5.23 yd3)
4.60 m3 (6.02 yd3)
5.00 m3 (6.54 yd3)
Material Density
GeneralPurpose
Rock
MaterialHandling/Standard
MaterialHandling
Stan
dard
Lin
kage
Pin
On
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
NOTE: All buckets are showing Bolt-On Edges.
23-284 Edition 44
Wheel LoadersIntegrated Toolcarriers
Bucket Selection● 972H
PHB-Sec23(pg175-290).indd 284PHB-Sec23(pg175-290).indd 284 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-285
Bucket Selection● 980H
Wheel LoadersIntegrated Toolcarriers
980H
800kg/m3
5.40 m3 (5.70 yd3) 6.21 m3 (8.12 yd3) 5.40 m3 (5.70 yd3)
6.56 m3 (8.58 yd3) 5.70 m3 (7.46 yd3)
6.90 m3 (9.02 yd3) 6.00 m3 (7.85 yd3)
6.56 m3 (8.58 yd3) 5.70 m3 (7.46 yd3)
5.06 m3 (6.62 yd3) 4.40 m3 (5.75 yd3)
9.43 m3 (12.33 yd3) 8.20 m3 (10.73 yd3)
6.56 m3 (8.58 yd3) 5.70 m3 (7.46 yd3)
5.70 m3 (7.46 yd3)
6.00 m3 (7.85 yd3)
5.70 m3 (7.46 yd3)
4.40 m3 (5.75 yd3)
8.20 m3 (10.73 yd3)
5.70 m3 (7.46 yd3)
Material Density
GeneralPurpose
Rock
Coal
General Purpose/Heavy Duty
MaterialHandling
Stan
dard
Lin
kage
Pin
On
900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
1348
700
1180lb/yd3Material Density
Bucket Fill Factors115% 110% 105% 100% 95%
1517 1685 1854 2022 2191 2359 2528 2696 2865 3033 3202 3370 3539 3707 3876 4044
NOTE: All buckets are showing Bolt-On Edges.
PHB-Sec23(pg175-290).indd 285PHB-Sec23(pg175-290).indd 285 12/20/13 9:07 AM12/20/13 9:07 AM
986H — Standard LiftMaterial Density Bucket Volume
kg/m3 tonnes/m3 lb/yd3 tons/yd3 m3 yd3
1632-1795 1.63-1.80 2750-3025 1.38-1.51 6.1 8
1740-1914 1.74-1.91 2933-3227 1.46-1.61 5.7 7.5
1865-2051 1.86-2.05 3143-3457 1.57-1.73 5.4 7
*Density range covers 100% rated payload to 110% rated payload in accordance with Large Wheel Loader payload policy.
23-286 Edition 44
Wheel LoadersIntegrated Toolcarriers
Bucket Selection● 986H
PHB-Sec23(pg175-290).indd 286PHB-Sec23(pg175-290).indd 286 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-287
Bucket Selection● 988K, 990H
Wheel LoadersIntegrated Toolcarriers
988KMaterial Density Bucket Volume
kg/m3 tonnes/m3 lb/yd3 tons/yd3 m3 yd3
1468-1614 1.47-1.61 2500-2750 1.25-1.38 7.7 10
1638-1801 1.64-1.80 2778-3056 1.39-1.53 6.9 9
1766-1942 1.77-1.94 3001-3300 1.50-1.65 6.4 8.33
990HMaterial Density Bucket Volume
kg/m3 tonnes/m3 lb/yd3 tons/yd3 m3 yd3
1590-1749 1.59-1.75 2692-2962 1.35-1.48 10 13
1728-1901 1.73-1.90 2917-3208 1.46-1.60 9.2 12
1849-2034 1.85-2.03 3111-3422 1.56-1.71 8.6 11.25
PHB-Sec23(pg175-290).indd 287PHB-Sec23(pg175-290).indd 287 12/20/13 9:07 AM12/20/13 9:07 AM
992K — Standard Up to specified density for 100% fill factor
Bucket Volume Material Density
m3 yd3 kg/m3 lb/yd3
12.2 16 1780 3000
11.5 15 1890 3200
10.7 14 2030 3430
992K — High Lift Up to specified density for 100% fill factor
Bucket Volume Material Density
m3 yd3 kg/m3 lb/yd3
12.2 16 1560 2630
11.5 15 1560 2630
10.7 14 1560 2630
993K — Standard Up to specified density for 100% fill factor
Bucket Volume Material Density
m3 yd3 kg/m3 lb/yd3
15.3 20 1780 3000
14.5 19 1870 3160
13.8 18 1970 3330
993K — High Lift Up to specified density for 100% fill factor
Bucket Volume Material Density
m3 yd3 kg/m3 lb/yd3
14.5 19 1720 2890
13.8 18 1810 3060
13.0 17 1920 3240
23-288 Edition 44
Wheel LoadersIntegrated Toolcarriers
Bucket Selection● 992K–993K
PHB-Sec23(pg175-290).indd 288PHB-Sec23(pg175-290).indd 288 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-289
Bucket Selection● 994H
Wheel LoadersIntegrated Toolcarriers
2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4
1.4 1.6 1.8 2.0 2.2 2.4 2.6
19
17
15
24.5
22.5
19.5
MATERIAL DENSITY (THOUSANDS)
994HRated Payload 34 470 kg (76,000 lb)
BU
CK
ET
CA
PAC
ITY
yd3m3
kg/m3
lb/yd3
2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4
1.4 1.6 1.8 2.0 2.2 2.4 2.6
19
17
15
24.5
22.5
19.5
MATERIAL DENSITY (THOUSANDS)
994H — High, Extended High LiftsRated Payload 30 840 kg (68,000 lb)
BU
CK
ET
CA
PAC
ITY
yd3m3
kg/m3
lb/yd3
% = Bucket Fill Factor
110% 95%100%
Standard
PHB-Sec23(pg175-290).indd 289PHB-Sec23(pg175-290).indd 289 12/20/13 9:07 AM12/20/13 9:07 AM
NOTE: Machines equipped same as those on Performance Data pages.
3.1 (4.0)
3.3 (4.25)
2.5 (3.25)
2.0 (2.6)
1.8 (2.4)
1.6 (2.0)
1.4 (1.8)1.3 (1.7)1.2 (1.6)
1.0 (1.31)
A
2000
2500
3000
3500
4000
4500
5000
1200
1500
1800
2100
2400
2700
3000
BUCKET SELECTION BASED ON MATERIAL DENSITY
lb/yd3
kg/m3
MATERIAL DENSITY
m3 (yd3)
BUCKETCAPACITY
KEY
A — IT14G2
23-290 Edition 44
Wheel LoadersIntegrated Toolcarriers
Bucket Selection● IT14G2
PHB-Sec23(pg175-290).indd 290PHB-Sec23(pg175-290).indd 290 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-291
Wheel LoadersIntegrated Toolcarriers
23
Travel Time — Loaded● 930K
● 20.5R-25 Tires
930K TRAVEL TIME — LOADED
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
Travel time assumes maximum governor pedal depression and automatic shifting in Range 4.
In load and carry applications it is important to consult the tire manufacturer on Ton-MPH ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 291PHB-Sec23(pg291-336).indd 291 12/20/13 9:07 AM12/20/13 9:07 AM
23-292 Edition 44
Wheel LoadersIntegrated Toolcarriers
Travel Time — Empty● 930K● 20.5R-25 Tires
930K TRAVEL TIME — EMPTY
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
Travel time assumes maximum governor pedal depression and automatic shifting in Range 4.
In load and carry applications it is important to consult the tire manufacturer on Ton-MPH ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 292PHB-Sec23(pg291-336).indd 292 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-293
Wheel LoadersIntegrated Toolcarriers
23
Travel Time — Loaded● 938K
● 20.5R-25 Tires
938K TRAVEL TIME — LOADED
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
Travel time assumes maximum governor pedal depression and automatic shifting in Range 4.
In load and carry applications it is important to consult the tire manufacturer on Ton-MPH ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 293PHB-Sec23(pg291-336).indd 293 12/20/13 9:07 AM12/20/13 9:07 AM
23-294 Edition 44
Wheel LoadersIntegrated Toolcarriers
Travel Time — Empty● 938K● 20.5R-25 Tires
938K TRAVEL TIME — EMPTY
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
Travel time assumes maximum governor pedal depression and automatic shifting in Range 4.
In load and carry applications it is important to consult the tire manufacturer on Ton-MPH ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 294PHB-Sec23(pg291-336).indd 294 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-295
Travel Time — Loaded● 950K ● 950H● 23.5-R25 Tires
Wheel LoadersIntegrated Toolcarriers
2%
4%6%
8%
10%
15%
20%
0
0.5
1
1.5
2
2.5
0 50 100 150 200 250
950K TRAVEL TIME — LOADED
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
2%
4%6%
8%
10%
15%
20%
0
0.5
1
1.5
2
2.5
3
0 50 100 150 200 250
950H TRAVEL TIME — LOADED
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
Not available in all regions. Contact your local Cat dealer for product availability.
Curves assume use of highest operating speed attainable.In load-and-carry applications it is important to consult the tire manufacturer on load-speed ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 295PHB-Sec23(pg291-336).indd 295 12/20/13 9:07 AM12/20/13 9:07 AM
23-296 Edition 44
Wheel LoadersIntegrated Toolcarriers
Travel Time — Empty● 950K ● 950H● 23.5-R25 Tires
2%4%
6%8%10%
15%
20%
0
0.5
1
1.5
2
0 50 100 150 200 250
950K TRAVEL TIME — EMPTY
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
2%4%
6%8%
10%
15%
20%
0
0.5
1
1.5
2
0 50 100 150 200 250
950H TRAVEL TIME — EMPTY
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
Not available in all regions. Contact your local Cat dealer for product availability.
Curves assume use of highest operating speed attainable.In load-and-carry applications it is important to consult the tire manufacturer on load-speed ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 296PHB-Sec23(pg291-336).indd 296 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-297
Travel Time — Loaded● 962K ● 962H● 23.5-R25 Tires
Wheel LoadersIntegrated Toolcarriers
2%
4%6%
8%
10%
15%
20%
0
0.5
1
1.5
2
2.5
0 50 100 150 200 250
962K TRAVEL TIME — LOADED
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
2%
4%6%
8%
10%
15%
20%
0
0.5
1
1.5
2
2.5
3
0 50 100 150 200 250
962H TRAVEL TIME — LOADED
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
Not available in all regions. Contact your local Cat dealer for product availability.
Curves assume use of highest operating speed attainable.In load-and-carry applications it is important to consult the tire manufacturer on load-speed ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 297PHB-Sec23(pg291-336).indd 297 12/20/13 9:07 AM12/20/13 9:07 AM
23-298 Edition 44
Wheel LoadersIntegrated Toolcarriers
Travel Time — Empty● 962K ● 962H● 23.5-R25 Tires
2%4%
6%8%10%
15%
20%
0
0.5
1
1.5
2
0 50 100 150 200 250
962K TRAVEL TIME — EMPTY
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
2%4%
6%8%10%
15%
20%
0
0.5
1
1.5
2
0 50 100 150 200 250
962H TRAVEL TIME — EMPTY
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
Not available in all regions. Contact your local Cat dealer for product availability.
Curves assume use of highest operating speed attainable.In load-and-carry applications it is important to consult the tire manufacturer on load-speed ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 298PHB-Sec23(pg291-336).indd 298 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-299
Wheel LoadersIntegrated Toolcarriers
23
Travel Time — Loaded and Empty● 966M
● 26.5-R25 Tires
2%4%6%8%10%
15%
20%
0
0.5
1
1.5
2
0 50 100 150 200 250
966M TRAVEL TIME — LOADED
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
966M TRAVEL TIME — EMPTY
2%4%6%
8%10%
15%
20%
0
0.5
1
1.5
0 50 100 150 200 250
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
These machines meet U.S. EPA Tier 4 Final/EU Stage IV emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
Curves assume use of highest operating speed attainable.In load-and-carry applications it is important to consult the tire manufacturer on load-speed ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 299PHB-Sec23(pg291-336).indd 299 12/20/13 9:07 AM12/20/13 9:07 AM
23-300 Edition 44
Wheel LoadersIntegrated Toolcarriers
Travel Time — Loaded● 966K ● 966H● 26.5-R25 Tires
2%
4%6%
8%
10%
15%
20%
0
0.5
1
1.5
2
2.5
0 50 100 150 200 250
966K TRAVEL TIME — LOADED
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
2%
4%6%
8%
10%
15%
20%
0
0.5
1
1.5
2
2.5
0 50 100 150 200 250
966H TRAVEL TIME — LOADED
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
Not available in all regions. Contact your local Cat dealer for product availability.
Curves assume use of highest operating speed attainable.In load-and-carry applications it is important to consult the tire manufacturer on load-speed ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 300PHB-Sec23(pg291-336).indd 300 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-301
Travel Time — Empty● 966K ● 966H● 26.5-R25 Tires
Wheel LoadersIntegrated Toolcarriers
2%4%
6%
8%10%
15%
20%
0
0.5
1
1.5
2
0 50 100 150 200 250
966K TRAVEL TIME — EMPTY
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
2%4%
6%8%10%
15%
20%
0
0.5
1
1.5
2
0 50 100 150 200 250
966H TRAVEL TIME — EMPTY
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
Not available in all regions. Contact your local Cat dealer for product availability.
Curves assume use of highest operating speed attainable.In load-and-carry applications it is important to consult the tire manufacturer on load-speed ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 301PHB-Sec23(pg291-336).indd 301 12/20/13 9:07 AM12/20/13 9:07 AM
23-302 Edition 44
Wheel LoadersIntegrated Toolcarriers
Travel Time — Loaded and Empty● 972M● 26.5-R25 Tires
2%4%6%8%10%
15%
20%
0
0.5
1
1.5
2
0 50 100 150 200 250
972M TRAVEL TIME — LOADED
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
972M TRAVEL TIME — EMPTY
2%4%6%
8%10%
15%
20%
0
0.5
1
1.5
0 50 100 150 200 250
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
These machines meet U.S. EPA Tier 4 Final/EU Stage IV emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
Curves assume use of highest operating speed attainable.In load-and-carry applications it is important to consult the tire manufacturer on load-speed ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 302PHB-Sec23(pg291-336).indd 302 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-303
Travel Time — Loaded● 972K ● 972H● 26.5-R25 Tires
Wheel LoadersIntegrated Toolcarriers
2%
4%6%
8%
10%
15%
20%
0
0.5
1
1.5
2
2.5
0 50 100 150 200 250
972K TRAVEL TIME — LOADED
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
2%
4%6%
8%
10%
15%
20%
0
0.5
1
1.5
2
2.5
0 50 100 150 200 250
972H TRAVEL TIME — LOADED
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
Not available in all regions. Contact your local Cat dealer for product availability.
Curves assume use of highest operating speed attainable.In load-and-carry applications it is important to consult the tire manufacturer on load-speed ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 303PHB-Sec23(pg291-336).indd 303 12/20/13 9:07 AM12/20/13 9:07 AM
23-304 Edition 44
Wheel LoadersIntegrated Toolcarriers
Travel Time — Empty● 972K ● 972H● 26.5-R25 Tires
2%4%
6%8%10%
15%
20%
0
0.5
1
1.5
2
0 50 100 150 200 250
972K TRAVEL TIME — EMPTY
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
2%4%
6%
8%10%
15%
20%
0
0.5
1
1.5
2
0 50 100 150 200 250
972H TRAVEL TIME — EMPTY
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
Not available in all regions. Contact your local Cat dealer for product availability.
Curves assume use of highest operating speed attainable.In load-and-carry applications it is important to consult the tire manufacturer on load-speed ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 304PHB-Sec23(pg291-336).indd 304 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-305
Travel Time — Loaded● 980K ● 980H● 29.5-R25 Tires
Wheel LoadersIntegrated Toolcarriers
2%
4%
6%
8%
10%
15%
20%
0
0.5
1
1.5
2
2.5
0 50 100 150 200 250
980K (NO LOCK-UP) TRAVEL TIME — LOADED
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
2%
4%
6%
8%
10%
15%
20%
0
0.5
1
1.5
2
2.5
0 50 100 150 200 250
980H TRAVEL TIME — LOADED
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
Not available in all regions. Contact your local Cat dealer for product availability.
Curves assume use of highest operating speed attainable.In load-and-carry applications it is important to consult the tire manufacturer on load-speed ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 305PHB-Sec23(pg291-336).indd 305 12/20/13 9:07 AM12/20/13 9:07 AM
Wheel LoadersIntegrated Toolcarriers
Travel Time — Empty● 980K ● 980H● 29.5-R25 Tires
23-306 Edition 44
2%4%
6%
8%10%
15%
20%
0
0.5
1
1.5
2
0 50 100 150 200 250
980K (NO LOCK-UP) TRAVEL TIME — EMPTY
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
2%4%
6%
8%10%
15%
20%
0
0.5
1
1.5
2
0 50 100 150 200 250
980H TRAVEL TIME — EMPTY
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
Not available in all regions. Contact your local Cat dealer for product availability.
Curves assume use of highest operating speed attainable.In load-and-carry applications it is important to consult the tire manufacturer on load-speed ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 306PHB-Sec23(pg291-336).indd 306 12/20/13 9:07 AM12/20/13 9:07 AM
23
Travel Time — Lock-Up Clutch● 980K
● 29.5-R25 Tires
Wheel LoadersIntegrated Toolcarriers
Edition 44 23-307
2%4%
6%8%10%
15%
20%
0
0.5
1
1.5
2
0 50 100 150 200 250
980K (LOCK-UP CLUTCH) TRAVEL TIME — LOADED
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
2%4%6%
8%
10%
15%
20%
0
0.5
1
1.5
0 50 100 150 200 250
980K (LOCK-UP CLUTCH) TRAVEL TIME — EMPTY
DISTANCE ONE WAY
TIM
E (
MIN
)
Meters
PE
RC
EN
T G
RA
DE
These machines meet U.S. EPA Tier 4 Interim/EU Stage IIIB emission standards and are only available in North America and Europe.Contact your local Cat dealer for product availability.
Curves assume use of highest operating speed attainable.In load-and-carry applications it is important to consult the tire manufacturer on load-speed ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 307PHB-Sec23(pg291-336).indd 307 12/20/13 9:07 AM12/20/13 9:07 AM
0 5 10 15 20 25 30 35 400
50
100
150
200
250
300
350
1F
2F
3F3F
4F
4F
2F
Wheel LoadersIntegrated Toolcarriers
988K Rimpull-Speed-Gradeability● Lock-Up Clutch
23-308 Edition 44
988KR
IMP
ULL
GROUND SPEED
kN
km/h
Direct Drive
PHB-Sec23(pg291-336).indd 308PHB-Sec23(pg291-336).indd 308 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-309
Travel Time — Loaded● 988K — Lock-Up Clutch
● 35/65-33 Tires
Wheel LoadersIntegrated Toolcarriers
988K TRAVEL TIME — LOADED
DIS
TAN
CE
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3
700
600
500
400
300
200
100
0
2% 4% 6% 8% 10% 15%
20%
0
20
40
60
80
100
120
140
160
180
200
220
TIME
Minutes
Feet Meters
NOTE: Curves assume use of highest operating speed attainable: 4th gear for 2%-6% TR, 3rd gear for 8%-10% TR, 2nd gear for 15% and 20% TR.
In load-and-carry applications it is important to consult the tire manufacturer on Ton-MPH ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 309PHB-Sec23(pg291-336).indd 309 12/20/13 9:07 AM12/20/13 9:07 AM
Wheel LoadersIntegrated Toolcarriers
Travel Time — Empty● 988K — Lock-Up Clutch● 35/65-33 Tires
23-310 Edition 44
988K TRAVEL TIME — EMPTY
DIS
TAN
CE
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
700
600
500
400
300
200
100
00 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3
0
20
40
60
80
100
120
140
160
180
200
2202% 4% 6% 8% 10% 15% 20%
TIME
Minutes
Feet Meters
NOTE: Curves assume use of highest operating speed attainable: 4th gear for 2%-8% TR, 3rd gear for 10%-15% TR, 2nd gear for 20% TR.
In load-and-carry applications it is important to consult the tire manufacturer on Ton-MPH ratings and pressure recommendations.
PHB-Sec23(pg291-336).indd 310PHB-Sec23(pg291-336).indd 310 12/20/13 9:07 AM12/20/13 9:07 AM
23
990H Rimpull-Speed-Gradeability Wheel LoadersIntegrated Toolcarriers
Edition 44 23-311
KEY
1 — 1st Gear2 — 2nd Gear3 — 3rd Gear
KEY
E — Empty 76 965 kg (169,677 lb)L — Loaded 91 934 kg (202,677 lb)
990HR
IMP
ULL
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
SPEED
0
10
20
30
40
50
60
70
80
90
100
110
120
130
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
45
40
2
35
30
25
5
20
15
10
50
60
55
1
3
3L
2L
2
E L
0
5
10
15
20
25
30
35
40
45
50
55
60
0 2 4 6 8 10 12 14 16 18 20 22 24
kg x1000
lb x1000
Calculated Pull: Idle HydraulicsCurves Assume NO SLIP Conditions
km/h
mph
PHB-Sec23(pg291-336).indd 311PHB-Sec23(pg291-336).indd 311 12/20/13 9:07 AM12/20/13 9:07 AM
23-312 Edition 44
Wheel LoadersIntegrated Toolcarriers
Travel Time — Loaded● 990H● 41.25/70-39 Tires
990H TRAVEL TIME — LOADED
DIS
TAN
CE
ON
E W
AYD
ISTA
NC
E O
NE
WAY
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
700
600
500
400
300
200
100
00 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3
2% 4% 6% 8% 10%
15%
20%
0
20
40
60
80
100
120
140
160
180
200
220
100
75
50
25
0
30
25
20
15
10
5
00.050 0.1 0.15 0.2
4%2% 6% 8% 10%15%
20%
TIME
TIME
Minutes
Feet
Feet
Meters
Meters
NOTE: Curves assume use of highest operating speed attainable: 3rd gear for 2%-8% TR, 2nd gear for 10%-20% TR.
In load-and-carry applications it is important to consult the tire manufacturer on Ton-MPH ratings and pressure recommendations.
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
Minutes
PHB-Sec23(pg291-336).indd 312PHB-Sec23(pg291-336).indd 312 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-313
Travel Time — Empty● 990H
● 41.25/70-39 Tires
Wheel LoadersIntegrated Toolcarriers
990H TRAVEL TIME — EMPTY
DIS
TAN
CE
ON
E W
AYD
ISTA
NC
E O
NE
WAY
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
700
600
500
400
300
200
100
00 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3
2% 4% 6% 8% 10% 15%
20%
0
20
40
60
80
100
120
140
160
180
200
220
100
75
50
25
0
30
25
20
15
10
5
00.050 0.1 0.15 0.2
4%2% 6% 8% 10% 15%
20%
TIME
TIME
Minutes
Feet
Feet
Meters
Meters
NOTE: Curves assume use of highest operating speed attainable: 3rd gear for 2%-10% TR, 2nd gear for 15% and 20% TR.
In load-and-carry applications it is important to consult the tire manufacturer on Ton-MPH ratings and pressure recommendations.
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
Minutes
PHB-Sec23(pg291-336).indd 313PHB-Sec23(pg291-336).indd 313 12/20/13 9:07 AM12/20/13 9:07 AM
Wheel LoadersIntegrated Toolcarriers
992K Rimpull-Speed-Gradeability● Standard Machine
23-314 Edition 44
KEY
1 — 1st Gear2 — 2nd Gear3 — 3rd Gear
KEY
E — Empty 92 797 kg (204,580 lb)L — Loaded 114 570 kg (252,580 lb)
992KR
IMP
ULL
TOTA
L R
ES
ISTA
NC
E %
(Gra
de
plu
s R
olli
ng
)
SPEED
0
20
40
60
80
100
120
140
0 2 4 6 8 10 12 14
45
40
2
35
30
25
5
20
15
10
50
60
55
1
3
2
0
5
10
15
20
25
30
35
40
45
50
55
60
65
0 2 4 6 8 10 12 14 16 18 20 22 24
E L
kg x1000
lb x1000
Calculated Pull: Idle HydraulicsCurves Assume NO SLIP Conditions
km/h
mph
PHB-Sec23(pg291-336).indd 314PHB-Sec23(pg291-336).indd 314 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-315
992K Rimpull-Speed-Gradeability● Lock-Up Clutch
Wheel LoadersIntegrated Toolcarriers
KEY
1 — 1st Gear2 — 2nd Gear3 — 3rd Gear
KEY
E — Empty 92 797 kg (204,580 lb)L — Loaded 114 570 kg (252,580 lb)
992KR
IMP
ULL
TOTA
L R
ES
ISTA
NC
E %
(Gra
de
plu
s R
olli
ng
)
SPEED
lb
Calculated Pull: Idle HydraulicsCurves Assume NO SLIP Conditions
mph
PHB-Sec23(pg291-336).indd 315PHB-Sec23(pg291-336).indd 315 12/20/13 9:07 AM12/20/13 9:07 AM
23-316 Edition 44
Wheel LoadersIntegrated Toolcarriers
Travel Time — Loaded● 992K● 45/65-45 Tires
992K TRAVEL TIME — LOADED
DIS
TAN
CE
ON
E W
AYD
ISTA
NC
E O
NE
WAY
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
700
600
500
400
300
200
100
00 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3
2% 4% 6% 8% 10%
20%
15%
0
20
40
60
80
100
120
140
160
180
200
220
100
75
50
25
0
30
25
20
15
10
5
00.050 0.1 0.15 0.2
4%2% 6% 8% 10%
20%
15%
TIME
TIME
Minutes
Feet
Feet
Meters
Meters
NOTE: Curves assume use of highest operating speed attainable: 3rd gear for 2%-10% TR, 2nd gear for 15% and 20% TR.
In load-and-carry applications it is important to consult the tire manufacturer on Ton-MPH ratings and pressure recommendations.
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
Minutes
PHB-Sec23(pg291-336).indd 316PHB-Sec23(pg291-336).indd 316 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-317
Travel Time — Empty● 992K
● 45/65-45 Tires
Wheel LoadersIntegrated Toolcarriers
992K TRAVEL TIME — EMPTY
DIS
TAN
CE
ON
E W
AYD
ISTA
NC
E O
NE
WAY
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
700
600
500
400
300
200
100
00 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3
2% 4% 6% 8% 10%
20%
15%
0
20
40
60
80
100
120
140
160
180
200
220
100
75
50
25
0
30
25
20
15
10
5
00.050 0.1 0.15 0.2
4%2% 6% 8% 10% 15%
20%
TIME
TIME
Minutes
Feet
Feet
Meters
Meters
NOTE: Curves assume use of highest operating speed attainable: 3rd gear for 2%-10% TR, 2nd gear for 15% and 20% TR.
In load-and-carry applications it is important to consult the tire manufacturer on Ton-MPH ratings and pressure recommendations.
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
Minutes
PHB-Sec23(pg291-336).indd 317PHB-Sec23(pg291-336).indd 317 12/20/13 9:07 AM12/20/13 9:07 AM
23-318 Edition 44
Wheel LoadersIntegrated Toolcarriers
993K Rimpull-Speed-Gradeability● Lock-Up Clutch
KEY
1 — 1st Gear2 — 2nd Gear3 — 3rd Gear
KEY
E — EmptyL — Loaded
993K
RIM
PU
LL
TOTA
L R
ES
ISTA
NC
E %
(Gra
de
plu
s R
olli
ng
)
SPEED
kg x1000
Calculated Pull: Idle HydraulicsCurves Assume NO SLIP Conditions
km/h
E L
PHB-Sec23(pg291-336).indd 318PHB-Sec23(pg291-336).indd 318 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-319
993K Rimpull-Speed-Gradeability● Lock-Up Clutch
Wheel LoadersIntegrated Toolcarriers
KEY
1 — 1st Gear2 — 2nd Gear3 — 3rd Gear
KEY
E — EmptyL — Loaded
993K
RIM
PU
LL
TOTA
L R
ES
ISTA
NC
E %
(Gra
de
plu
s R
olli
ng
)
SPEED
lb x1000
Calculated Pull: Idle HydraulicsCurves Assume NO SLIP Conditions
mph
E L
PHB-Sec23(pg291-336).indd 319PHB-Sec23(pg291-336).indd 319 12/20/13 9:07 AM12/20/13 9:07 AM
23-320 Edition 44
Wheel LoadersIntegrated Toolcarriers
Travel Time — Empty● 993K — Lock-Up Clutch● Idle Hydraulics
993K TRAVEL TIME — EMPTY
DIS
TAN
CE
ON
E W
AY
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
2202% 6% 8%
4%10% 15%
180
200
120
140
160
20%
80
100
120
40
60
0
20
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3
TIME
Minutes
Meters
PHB-Sec23(pg291-336).indd 320PHB-Sec23(pg291-336).indd 320 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-321
Travel Time — Loaded● 993K — Lock-Up Clutch
● Idle Hydraulics
Wheel LoadersIntegrated Toolcarriers
993K TRAVEL TIME — LOADED
DIS
TAN
CE
ON
E W
AY
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
2202%
4%6% 8% 10%
180
200
140
16015%
100
120 20%
60
80
0
20
40
00.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3
TIME
Minutes
Meters
PHB-Sec23(pg291-336).indd 321PHB-Sec23(pg291-336).indd 321 12/20/13 9:07 AM12/20/13 9:07 AM
23-322 Edition 44
Wheel LoadersIntegrated Toolcarriers
Travel Time — Empty● 993K — Standard● Idle Hydraulics
993K TRAVEL TIME — EMPTY
DIS
TAN
CE
ON
E W
AY
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
2204%2% 6% 8% 10%
180
20015%
120
140
160
20%
80
100
120
40
60
0
20
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3
TIME
Minutes
Meters
PHB-Sec23(pg291-336).indd 322PHB-Sec23(pg291-336).indd 322 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-323
Travel Time — Loaded● 993K — Standard
● Idle Hydraulics
Wheel LoadersIntegrated Toolcarriers
993K TRAVEL TIME — LOADED
DIS
TAN
CE
ON
E W
AY
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
2202% 4% 6% 8% 10%
180
200
140
160
15%
100
120 20%
60
80
0
20
40
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3
TIME
Minutes
Meters
PHB-Sec23(pg291-336).indd 323PHB-Sec23(pg291-336).indd 323 12/20/13 9:07 AM12/20/13 9:07 AM
23-324 Edition 44
Wheel LoadersIntegrated Toolcarriers
994H Rimpull-Speed-Gradeability
KEY
1 — 1st Gear2 — 2nd Gear3 — 3rd Gear
KEY
E — Empty 189 345 kg (417,429 lb)L — Loaded 223 819 kg (493,429 lb)
994HR
IMP
ULL
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
SPEED
0
20
40
60
80
100
120
140
160
180
200
220
0 2 4 6 8 10 12 14 16
45
40
2
35
30
25
5
20
15
10
50
1
3L
2L3
2
0 2 4 6 8 10 12 14 16 18 20 22 24
0
10
20
30
40
50
60
70
80
90
100
E L
kg x1000
lb x1000
Calculated Pull: Idle HydraulicsCurves Assume NO SLIP Conditions
km/h
mph
PHB-Sec23(pg291-336).indd 324PHB-Sec23(pg291-336).indd 324 12/20/13 9:07 AM12/20/13 9:07 AM
23
Travel Time — Loaded● 994H
● 50/80-57 Tires
Wheel LoadersIntegrated Toolcarriers
Edition 44 23-325
994H TRAVEL TIME — LOADED
DIS
TAN
CE
ON
E W
AYD
ISTA
NC
E O
NE
WAY
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
700
600
500
400
300
200
100
00 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3
2% 4% 6% 8% 10% 15%
20%
0
20
40
60
80
100
120
140
160
180
200
220
100
75
50
25
0
30
25
20
15
10
5
00.050 0.1 0.15 0.2
4%2% 6% 8% 10% 15%
20%
TIME
TIME
Minutes
Feet
Feet
Meters
Meters
NOTE: Curves assume use of highest operating speed attainable: 3rd gear for 2%-10% TR, 2nd gear for 15% and 20% TR.
In load-and-carry applications it is important to consult the tire manufacturer on Ton-MPH ratings and pressure recommendations.
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
Minutes
PHB-Sec23(pg291-336).indd 325PHB-Sec23(pg291-336).indd 325 12/20/13 9:07 AM12/20/13 9:07 AM
23-326 Edition 44
Wheel LoadersIntegrated Toolcarriers
Travel Time — Empty● 994H● 50/80-57 Tires
994H TRAVEL TIME — EMPTY
DIS
TAN
CE
ON
E W
AY
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
700
600
500
400
300
200
100
00 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3
2% 4% 6% 8% 10% 15%20%
0
20
40
60
80
100
120
140
160
180
200
220
100
75
50
25
0
30
25
20
15
10
5
00.050 0.1 0.15 0.2
4%2% 6% 8% 10% 15% 20%
TIME
TIME
Minutes
Feet Meters
NOTE: Curves assume use of highest operating speed attainable: 3rd gear for 2%-10% TR, 2nd gear for 15% and 20% TR.
In load-and-carry applications it is important to consult the tire manufacturer on Ton-MPH ratings and pressure recommendations.
DIS
TAN
CE
ON
E W
AY
TOTAL RESISTANCE(Grade plus Rolling)
Feet Meters
Minutes
PHB-Sec23(pg291-336).indd 326PHB-Sec23(pg291-336).indd 326 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-327
Travel Time — Loaded● 994H Steady State
● 50/80-57 Tires
Wheel LoadersIntegrated Toolcarriers
994H TRAVEL TIME — LOADED
DIS
TAN
CE
ON
E W
AYD
ISTA
NC
E O
NE
WAY
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
700
600
500
400
300
200
100
00 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3
2% 4% 6% 8% 10%
20%
15%
0
20
40
60
80
100
120
140
160
180
200
220
100
75
50
25
0
30
25
20
15
10
5
00.050 0.1 0.15 0.2
4%2% 6% 8% 10%
20%
15%
TIME
TIME
Minutes
Feet
Feet
Meters
Meters
NOTE: Curves assume use of highest operating speed attainable: 3rd gear for 2%-8% TR, 2nd gear for 10% and 15% TR, 1st gear for 20% TR.
In load-and-carry applications it is important to consult the tire manufacturer on Ton-MPH ratings and pressure recommendations.
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
Minutes
PHB-Sec23(pg291-336).indd 327PHB-Sec23(pg291-336).indd 327 12/20/13 9:07 AM12/20/13 9:07 AM
23-328 Edition 44
Wheel LoadersIntegrated Toolcarriers
Travel Time — Empty● 994H Steady State● 50/80-57 Tires
994H TRAVEL TIME — EMPTY
DIS
TAN
CE
ON
E W
AYD
ISTA
NC
E O
NE
WAY
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
700
600
500
400
300
200
100
00 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3
2% 4% 6% 8% 10%
20%
15%
0
20
40
60
80
100
120
140
160
180
200
220
100
75
50
25
0
30
25
20
15
10
5
00.050 0.1 0.15 0.2
4%2% 6% 8% 10% 15%
20%
TIME
TIME
Minutes
Feet
Feet
Meters
Meters
NOTE: Curves assume use of highest operating speed attainable: 3rd gear for 2%-10% TR, 2nd gear for 15% TR, 1st gear for 20% TR.
In load-and-carry applications it is important to consult the tire manufacturer on Ton-MPH ratings and pressure recommendations.
TOTA
L R
ES
ISTA
NC
E(G
rad
e p
lus
Ro
llin
g)
Minutes
PHB-Sec23(pg291-336).indd 328PHB-Sec23(pg291-336).indd 328 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-329
Production Estimating Table● m3 or yd3/60 min. hour
Wheel LoadersIntegrated Toolcarriers
Bucket Size (m3 or yd3) 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0
Cycle Time
Cycles Per Hr Unshaded area indicates average production.
0.35 171
0.40 150 150 225 330 375 450 525
0.45 133 135 200 268 332 400 466 530 600 665 730 800 865
0.50 120 120 180 240 300 360 420 480 540 600 660 720 780 840 900 960 1003 1080 1140 1200
0.55 109 109 164 218 272 328 382 436 490 545 600 655 705 765 820 870 925 980 1008 1090
0.60 100 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000
0.65 92 92 138 184 230 276 322 368 416 460 505 555 600 645 690 735 780 830 875 920
0.70 86 342 386 430 474 515 560 600 645 690 730 775 815 860
0.75 80 560 600 640 680 720 760 800
Bucket Size (m3 or yd3) 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 19.0 20.0 21.0 22.0 23.0 24.0 25.0 26.0
Cycle Time
Cycles Per Hr
Unshaded area indicates average production.0.35 171
0.40 150
0.45 133
0.50 120 1320 1440
0.55 109 1200 1310 1420 1520 1635 1740 1850 1960 2070 2180 2285 2395 2505 2615 2725 2830
0.60 100 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400 2500 2600
0.65 92 1010 1105 1195 1285 1380 1470 1560 1655 1745 1840 1930 2020 2115 2205 2300 2390
0.70 86 945 1030 1120 1200 1290 1375 1460 1545 1630 1720 1805 1890 1975 2060 2150 2235
0.75 80 880 960 1040 1120 1200 1280 1360 1440 1520 1600 1680 1760 1840 1920 2000 2080
0.80 75 975 1050 1125 1200 1275 1350 1425 1500 1575 1650 1725 1800 1875 1950
Job Efficiency Worktime/Hr
Efficiency Factor Bucket Load Factor
60 Min Hr 100% Bucket Size × 1.00
55 91% 0.95
50 83% 0.90
45 75% 0.85
40 69% 0.80
— — 0.75
PHB-Sec23(pg291-336).indd 329PHB-Sec23(pg291-336).indd 329 12/20/13 9:07 AM12/20/13 9:07 AM
23-330 Edition 44
Wheel LoadersIntegrated Toolcarriers
Production Estimating Table● 60 min hour ● Shot Rock● Metric Tons
Metric Tons ● 1600 kg Lm3 (1.6 t) density
Bucket Size m3 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5
Cycle Time
Cycles Per Hr Unshaded area indicates average production.
0.40 150 240 360 480 600 720
0.45 133 213 319 426 532 638 745 851 958 1064 1170
0.50 120 192 288 384 480 576 672 768 864 960 1056 1152 1248 1344 1440 1536 1632 1730 1825
0.55 109 174 262 349 436 523 610 698 785 872 959 1046 1134 1221 1308 1395 1482 1570 1655
0.60 100 160 240 320 400 480 560 640 720 800 880 960 1040 1120 1200 1280 1360 1440 1520
0.65 92 147 221 294 368 442 515 589 662 736 810 883 957 1030 1104 1178 1251 1325 1400
0.70 86 482 550 619 688 757 826 894 963 1032 1101 1170 1238 1310
0.75 80 768 832 896 960 1024 1088 1150 1215
Bucket PayloadMetric (Tons) 1.6 2.4 3.2 4.0 4.8 5.6 6.4 7.2 8.0 8.8 9.6 10.4 11.2 12.0 12.8 13.6 14.4 15.2
Bucket Size m3 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 19.0 20.0
Cycle Time
Cycles Per Hr
Unshaded area indicates average production.0.40 150
0.45 133
0.50 120
0.55 109 1744 1918 2092 2267 2441 2616 2790 2964 3139 3313 3488
0.60 100 1600 1760 1920 2080 2240 2400 2560 2720 2880 3040 3200
0.65 92 1472 1619 1766 1913 2060 2208 2355 2502 2649 2796 2944
0.70 86 1376 1513 1651 1788 1926 2064 2201 2339 2476 2614 2752
0.75 80 1280 1408 1536 1664 1792 1920 2048 2176 2304 2432 2560
0.80 75 1200 1320 1440 1560 1680 1800 1920 2040 2160 2280 2400
Bucket Payload Metric (Tons) 16.0 17.6 19.2 20.8 22.4 24.0 25.6 27.2 28.8 30.4 32.0
PHB-Sec23(pg291-336).indd 330PHB-Sec23(pg291-336).indd 330 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-331
Production Estimating Table● Shot Rock ● 60 min hour
● U.S. Tons
Wheel LoadersIntegrated Toolcarriers
U.S. Tons ● 2700 lb/LCY (1.35 T) density
Bucket Size yd3 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0
CycleTime
CyclesPer Hr Unshaded area indicates average production.
0.40 150 203 330 420 510 615 705 810
0.45 133 180 293 360 454 545 625 720 810 905 985 1080 1170
0.50 120 162 254 324 408 492 565 650 730 815 890 970 1060 1140 1200 1300 1380 1470 1540 1620
0.55 109 147 240 294 370 448 515 590 665 740 805 885 960 1030 1090 1180 1250 1330 1400 1740
0.60 100 135 220 270 340 410 470 540 610 680 740 810 880 950 1000 1080 1150 1220 1280 1350
0.65 92 124 200 250 314 380 435 500 560 625 680 750 810 875 920 985 1060 1120 1180 1250
0.70 86 525 585 635 695 755 815 860 930 990 1050 1100 1160
0.75 80 760 800 865 920 975 1030 1080
Bucket Payload (Tons) 1.35 2.2 2.7 3.4 4.1 4.7 5.4 6.1 6.8 7.4 8.1 8.8 9.5 10.0 10.8 11.5 12.2 12.8 13.5
Bucket Size yd3 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 19.0 20.0 21.0 22.0 23.0 24.0 25.0 26.0
Cycle Time
Cycles Per Hr
Unshaded area indicates average production.0.40 150
0.45 133
0.50 120 1782 1945
0.55 109 1620 1765 1905 2060 2200 2350 2495 2645 2790 2940 3080 3235 3375 3530 3670 3825
0.60 100 1485 1620 1750 1890 2020 2160 2290 2430 2560 2700 2830 2970 3100 3240 3370 3510
0.65 92 1365 1490 1610 1735 1855 1985 2105 2235 2355 2480 2600 2730 2850 2980 3100 3225
0.70 86 1275 1390 1505 1625 1735 1855 1965 2085 2200 2320 2430 2550 2665 2785 2895 3015
0.75 80 1190 1295 1400 1510 1615 1725 1830 1940 2045 2160 2260 2375 2480 2590 2695 2805
0.80 75 1310 1415 1515 1620 1715 1820 1920 2025 2120 2225 2325 2430 2525 2630
Bucket Payload (Tons) 14.9 16.4 17.5 18.9 20.2 21.6 22.9 24.3 25.6 27.0 28.3 29.7 31.0 32.4 33.7 35.1
PHB-Sec23(pg291-336).indd 331PHB-Sec23(pg291-336).indd 331 12/20/13 9:07 AM12/20/13 9:07 AM
23-332 Edition 44
Wheel LoadersIntegrated Toolcarriers
Work Tools● Wheel Loaders
Work Tools 904H
908H
2, 9
07H
2, 9
06H
2
914G
2, IT
14G
2
910K
914K
924K
930K
938K
950K
, 962
K
950H
, 962
H
966H
, 966
K, 9
66M
, 972
H, 9
72K
, 972
M
980K
, 980
H
988K
988H
990H
992K
993K
994H
, 994
F
Fusion Quick Coupler X X X X X X
Quick Coupler X X X X X
Performance Series General Purpose Bucket
X X X X X X X X X X X
General Purpose Bucket X X X X X X X
Performance Series Material Handling Bucket
X X X X
Material Handling Bucket X X X X X X
Sand & Gravel Bucket X X X
Performance Series Coal Bucket X X X
Coal Bucket X X X X X X X X X X X
Performance Series Rock Bucket X X X X X X
Rock Bucket X X X X X X X X
Performance Series Heavy Duty Rock Bucket
X X X
Heavy Duty Rock Bucket X X X X
Performance Series Heavy Duty Granite Bucket
X X
Heavy Duty Granite Bucket X X X X
Heavy Abrasion Rock Bucket X X
Iron Ore Bucket X X X X
Serrated Edge Rock Bucket X X X X
Multi-purpose Bucket X X X X X X X X X X X
Side Dump Bucket X X X X X X X X X
High Dump Bucket X X X X X X
Grapple Bucket X X X X X X X X
Waste Handling Bucket X X X X X X X
Woodchip Bucket X X X X X X X X X X
Slag Bucket X X X X
Fertilizer Bucket X X X
Grading Bucket X X X
Light Material Bucket X X X X X X X X
NOTE: List is not all-inclusive. Contact your Cat dealer for special attachment needs.
PHB-Sec23(pg291-336).indd 332PHB-Sec23(pg291-336).indd 332 12/20/13 9:07 AM12/20/13 9:07 AM
Edition 44 23-333
Wheel LoadersIntegrated Toolcarriers
23
Work Tools● Wheel Loaders
Work Tools 904H
908H
2, 9
07H
2, 9
06H
2
914G
2, IT
14G
2
910K
914K
924K
930K
938K
950K
, 962
K
950H
, 962
H
966H
, 966
K, 9
66M
, 972
H, 9
72K
, 972
M
980K
, 980
H
988K
988H
990H
992K
993K
994H
, 994
F
Pallet Fork X X X X X X X X X X X X X
Construction Fork X X X
Log & Lumber Fork X X X X X X X X X
Logging Fork X X X X X X
Millyard Fork X X X X X X
Unloading Grapple Fork X X X
Pipe & Pole Fork X X X X X
Asphalt Cutters X X
Auger X X
Blade X X
Angle Broom X X X X X X X X X X
Special Application Broom X X X X X X X X X X
Pickup Broom X X X X X X X X
Cold Planer X X
Compactors X X
Landscape Tillers X X
Material Handling Arm X X X X X X X X X X X X
Rake X X X X X X X X
Reversible Plow X X X X X X X X X X
V-plow X X X X X X X X
Snow Blower X X
Snow Push X X X X X X X
Stump Grinder X X
Trencher X X
Wheel Saw X
Block Handling Tools X X X
NOTE: List is not all-inclusive. Contact your Cat dealer for special attachment needs.
PHB-Sec23(pg291-336).indd 333PHB-Sec23(pg291-336).indd 333 12/20/13 9:07 AM12/20/13 9:07 AM
23-334 Edition 44
Wheel LoadersIntegrated Toolcarriers
BUCKETSPerformance Series — optimized fill factors for use in truck loading, stockpiling and load-and-carry applications.General Purpose — provide good all-around performance for stockpiling, re-handling, excavating and bank loading.Material Handling — designed for efficient loading of stock piled materials.Coal — high-volume material movers, for loading and stock piling coal and other materials of similar density.
Rock — designed for high production in abrasive applications.Multi-Purpose — versatile … loads, strips topsoil, bull-dozes, clamps pipe, and cleans up debris, plus many other tasks.Side Dump — dump forward or to the left … ideal in tight quarters or to reduce turning time.High Dump — for extended dump height of light materials.Grapple — equipped with dual top clamps to grab and hold loose material.Waste Handling — move large volumes for low-density refuse in transfer stations, landfills and recycling yards.Woodchip — optimized for moving large volumes of wood chips.Slag — heavy duty and specifically constructed to handle extreme conditions that come with handling hot slag.
FORKSPallet — for a variety of task, tines are adjustable and available in several different lengths.Log & Lumber — flat tines and raised back are designed specifically for use in handling both unfinished logs and stack lumber. Available with top clamp.Logging — equipped with two independent top clamps, for use loading and unloading trucks and feeding the mill.Millyard — equipped with one-piece top clamp, built for moving, sorting and feeding the mill.Unloading Grapple — short tines and large top clamp opening ideal for unloading logs from trucks.Pipe & Pole — wide carriage, fixed tines and full width double-acting clamp are ideal for transporting, loading and unloading pipe.
AND MORE ...Brooms — for street or job site cleanup, snow removal etc. Angle, Special Application and Pick-up models available.Material Handling Arms — provides a tool that can pick, carry and load a variety of materials. Arm length can be adjusted.Plows — ideal for snow clearing, available in angling and V-plow styles.Rakes — versatile tools that work well in light-duty, medium-duty and heavy-duty land clearing situations. Available with top clamp.
Integrated Toolcarriers Work ToolsWork Tools IT14G2 910K 914KPerformance Series
General Purpose BucketX X
General Purpose Bucket X X XMaterial Handling Bucket X X XCoal BucketMulti-Purpose Bucket X XSide Dump Bucket X XHigh Dump BucketGrapple BucketWaste Handling BucketWoodchip BucketPallet Fork X X XLog & Lumber ForkLogging ForkMillyard ForkGrapple ForkAsphalt CutterStraight BladeAngle Blade X XAngle Broom X XSpecial Application BroomPick-up BroomMaterial Handling Arm X X XReversible PlowV-plowOne Way PlowRakeThis list not all inclusive. Contact your Cat dealer for special attachment needs.
Work Tools
PHB-Sec23(pg291-336).indd 334PHB-Sec23(pg291-336).indd 334 12/20/13 9:07 AM12/20/13 9:07 AM
23
Edition 44 23-335
Fusion Coupler System● NACD, LACD, EAME
Wheel LoadersIntegrated Toolcarriers
FUSION COUPLER SYSTEMCaterpillar is breaking new ground with the Fusion
Coupler System. Caterpillar engineers designed this new system to exceed the performance of any other Cat or competitive coupler solution in the marketplace. This coupler system is a factory- or field-installed option for Cat Loaders from 924K through 972, including IT38 and IT62 machines. Fusion offers benefits in four main categories:
PerformanceThis new, patented interface provides coupler flexi-
bility with performance virtually identical to pin-on.Imagine lifting a hundred-pound box with your arms
fully extended. Now, imagine lifting that same load close to your body. That’s the genius of Fusion: designed to integrate the work tool and the machine by pulling the coupler and tool closer to the wheel loader. As a result, the center of gravity is moved inward, towards the machine. This translates to increased lifting ability when compared to machines equipped with competing coupler systems.
DurabilityThe advanced wedging mechanism of the Fusion
Coupler creates a tight, rattle-free fit. This new lock up system eliminates play and wear — resulting in a long service life.
Wedges pull the attachment tight to the machine in two directions — in and down. Constant hydraulic pres-sure on the coupler wedges compensate for wear, assur-ing a tight fit throughout the life of the coupler. Tight fit gives better tool control and increased productivity. Plus, coupler durability is substantially increased over tradi-tional couplers.
VisibilityA new, open coupler frame design opens sight lines
from the operator’s seat, making it easier than ever before to engage and disengage attachments with certainty.
Offset tines and other design changes to Fusion Pallet Forks, working in conjunction with the Fusion Coupler, increase visibility substantially at ground level and truck bed height when compared to tradi tional coupler and fork combinations.
Flexibility/CompatibilityWith the Fusion Coupler system, Caterpillar customers
get one common interface. This unique, single interface eliminates the need for many different couplers across the entire range of Cat Small and Medium Wheel Loaders. This expanded machine compatibility not only allows one machine to pick up a range of work tools, but also for one work tool to be used by a host of different machines. Realize the flexibility and opportunity afforded your rental operation, or the improvements to machine and work tool management on your customers’ job sites.
Fusion is supported by a full line of work tools. Just about any work tool available for pin-on is also available, or can be converted, to work with Fusion. For complete information on Fusion work tools available for Cat Loaders 924 through 972, consult Fusion Product Bulletin GEJQ0222.
PHB-Sec23(pg291-336).indd 335PHB-Sec23(pg291-336).indd 335 12/20/13 9:07 AM12/20/13 9:07 AM
Fusion Work Tools 924K
930K
938K
950K
, 962
K
950H
, 962
H
IT62
H/G
966K
/H
972K
/H
Performance Series General Purpose Bucket X X X X X X X
General Purpose Bucket X X X X X
Performance Series Material Handling Bucket X X X X X X
Material Handling Bucket X X X X X
Performance Series Coal Bucket X X
Coal/Light Material Bucket X X X X
Performance Series Rock Bucket X X X
Rock Bucket X X X X
Multi-purpose Bucket X X X X X
Side Dump Bucket X X X X X X X X
High Dump Bucket X X X X X X X X
Grapple Bucket X X X X X X X X
Waste Handling Bucket X X X X X X X X
Woodchip Bucket X X X X X X X X
Pallet Fork X X X X X X X X
Log & Lumber Fork X X X X X X X X
Logging Fork X
Millyard Fork X X X X
Grapple Fork X
Pipe & Pole Fork X X X X X X X
Angle Broom X X X X X
Special Application Broom X X X X X
Pickup Broom X X X
Material Handling Arm X X X X X X X X
Rake X X X X X X X X
Reversible Plow X X X X X X X X
V-plow X X X X
NOTE: This list is not all-inclusive. Contact your Cat dealer for special attachment needs.
23-336 Edition 44
Wheel LoadersIntegrated Toolcarriers
Fusion Coupler System● Work Tools
PHB-Sec23(pg291-336).indd 336PHB-Sec23(pg291-336).indd 336 12/20/13 9:07 AM12/20/13 9:07 AM