Wes Demirjian Report Out
-
Upload
wesley-demirjian -
Category
Documents
-
view
96 -
download
0
Transcript of Wes Demirjian Report Out
![Page 1: Wes Demirjian Report Out](https://reader034.fdocuments.us/reader034/viewer/2022042800/58ebcc5f1a28ab47598b46fd/html5/thumbnails/1.jpg)
Wes Demirjian
Freestanding NPI
![Page 2: Wes Demirjian Report Out](https://reader034.fdocuments.us/reader034/viewer/2022042800/58ebcc5f1a28ab47598b46fd/html5/thumbnails/2.jpg)
• From Nashville, TN
• Junior at TN Tech
University
• Mechanical Engineering
• First Rotation
• Freestanding NPI
• Mentor: Jamie Little
![Page 3: Wes Demirjian Report Out](https://reader034.fdocuments.us/reader034/viewer/2022042800/58ebcc5f1a28ab47598b46fd/html5/thumbnails/3.jpg)
• Literature
• Controls Rework
• Torque Tests
• Pre-Pilot Build
• Other Assignments
![Page 4: Wes Demirjian Report Out](https://reader034.fdocuments.us/reader034/viewer/2022042800/58ebcc5f1a28ab47598b46fd/html5/thumbnails/4.jpg)
• New models (with new
software) mean new literature
• Proofread existing manuals,
omitting obsolete details and
adding new information
• Used new graphics to form a
rough draft of what the new
Use and Cares might look like
![Page 5: Wes Demirjian Report Out](https://reader034.fdocuments.us/reader034/viewer/2022042800/58ebcc5f1a28ab47598b46fd/html5/thumbnails/5.jpg)
• Updating software and hardware separately caused EMI
issues
• Fixed issues by modifying one connection on circuit
board
![Page 6: Wes Demirjian Report Out](https://reader034.fdocuments.us/reader034/viewer/2022042800/58ebcc5f1a28ab47598b46fd/html5/thumbnails/6.jpg)
• Problems with stripping
screws during previous build
• Took different fasteners and
different hole types to test the start
and strip torques of all possible
production variations
![Page 7: Wes Demirjian Report Out](https://reader034.fdocuments.us/reader034/viewer/2022042800/58ebcc5f1a28ab47598b46fd/html5/thumbnails/7.jpg)
One instance (CR control trim) showed that only one out of
three of the current screws was satisfactory in a sense that the
maximum start and minimum strip torques were a great deal
separated
![Page 8: Wes Demirjian Report Out](https://reader034.fdocuments.us/reader034/viewer/2022042800/58ebcc5f1a28ab47598b46fd/html5/thumbnails/8.jpg)
![Page 9: Wes Demirjian Report Out](https://reader034.fdocuments.us/reader034/viewer/2022042800/58ebcc5f1a28ab47598b46fd/html5/thumbnails/9.jpg)
• Rework
• Loops
• UL/Miswire FMEA
• Overlay Tape Design
![Page 10: Wes Demirjian Report Out](https://reader034.fdocuments.us/reader034/viewer/2022042800/58ebcc5f1a28ab47598b46fd/html5/thumbnails/10.jpg)
• Warping Control
Trims: Details
• Doors failing STTs:
Analyzing
• DST
Abrasions:
Simplicity
![Page 11: Wes Demirjian Report Out](https://reader034.fdocuments.us/reader034/viewer/2022042800/58ebcc5f1a28ab47598b46fd/html5/thumbnails/11.jpg)
• Everything in industry takes longer than
expected
• Flexibility is
essential
• It’s not what you know, but who you
know
![Page 12: Wes Demirjian Report Out](https://reader034.fdocuments.us/reader034/viewer/2022042800/58ebcc5f1a28ab47598b46fd/html5/thumbnails/12.jpg)
![Page 13: Wes Demirjian Report Out](https://reader034.fdocuments.us/reader034/viewer/2022042800/58ebcc5f1a28ab47598b46fd/html5/thumbnails/13.jpg)