Week 9 Deliverables Team Highlander 3/10/10. Continued Analysis Added moment to handle, no...
-
Upload
louisa-casey -
Category
Documents
-
view
212 -
download
0
Transcript of Week 9 Deliverables Team Highlander 3/10/10. Continued Analysis Added moment to handle, no...
![Page 1: Week 9 Deliverables Team Highlander 3/10/10. Continued Analysis Added moment to handle, no significant change in tipping problem With a 25 lb weight,](https://reader036.fdocuments.us/reader036/viewer/2022080915/56649d8b5503460f94a72d4d/html5/thumbnails/1.jpg)
Week 9 Deliverables
Team Highlander3/10/10
![Page 2: Week 9 Deliverables Team Highlander 3/10/10. Continued Analysis Added moment to handle, no significant change in tipping problem With a 25 lb weight,](https://reader036.fdocuments.us/reader036/viewer/2022080915/56649d8b5503460f94a72d4d/html5/thumbnails/2.jpg)
Continued Analysis
• Added moment to handle, no significant change in tipping problem
• With a 25 lb weight, wrist generates roughly 4.2 ft-lb of torque
• Original moment was -86.3 ft-lb for the entire frame, so doesn’t effect tipping
![Page 3: Week 9 Deliverables Team Highlander 3/10/10. Continued Analysis Added moment to handle, no significant change in tipping problem With a 25 lb weight,](https://reader036.fdocuments.us/reader036/viewer/2022080915/56649d8b5503460f94a72d4d/html5/thumbnails/3.jpg)
Manufacturing Materials
• Handle Bars• Stopper (counter moment)• Linkage arms• Lever• Made with 6061-T6 Aluminum– Same material used on good bicycle frames– Low cost ($4.68/2 ft 3/4 SCH 40 (1.05 OD X .113W)) – High yield stress (400 MPa)
![Page 4: Week 9 Deliverables Team Highlander 3/10/10. Continued Analysis Added moment to handle, no significant change in tipping problem With a 25 lb weight,](https://reader036.fdocuments.us/reader036/viewer/2022080915/56649d8b5503460f94a72d4d/html5/thumbnails/4.jpg)
Manufacturing Materials
• Pins and Bolts– Steel, found readily at a variety of locations– Standard sizes used – nothing custom-made
• Handle and lever grips– Silicon, good cushion level and relatively cheap,
easy to mold
![Page 5: Week 9 Deliverables Team Highlander 3/10/10. Continued Analysis Added moment to handle, no significant change in tipping problem With a 25 lb weight,](https://reader036.fdocuments.us/reader036/viewer/2022080915/56649d8b5503460f94a72d4d/html5/thumbnails/5.jpg)
Manufacturing - Prototype
• Bars will be shipped as pipes, and will be machined by Team Highlander
• Bolts/Pins purchased at Home Depot• Handle and lever grips– Use bicycle handlebar tape– Good cushion level, high quality, does not require
any sort of injection molding– Costs approximately $20
• Handle bar pivot will be clamped onto the frame
![Page 6: Week 9 Deliverables Team Highlander 3/10/10. Continued Analysis Added moment to handle, no significant change in tipping problem With a 25 lb weight,](https://reader036.fdocuments.us/reader036/viewer/2022080915/56649d8b5503460f94a72d4d/html5/thumbnails/6.jpg)
CastingSmall Volume Large Volume
![Page 7: Week 9 Deliverables Team Highlander 3/10/10. Continued Analysis Added moment to handle, no significant change in tipping problem With a 25 lb weight,](https://reader036.fdocuments.us/reader036/viewer/2022080915/56649d8b5503460f94a72d4d/html5/thumbnails/7.jpg)
Manufacturing – Final Product1-1,000 Units
• Type of manufacturing used– Handle bars: extrusion (hot)– Handle grips: injection molding– Curved stopper legs: sand casting (or plaster)– Pins/Bolts: sand casting– Lever bars: extrusion (hot)– Lever handles: injection molding– Linkage rods: extrusion (hot)– Lever/handle brackets: sand casting/welding
![Page 8: Week 9 Deliverables Team Highlander 3/10/10. Continued Analysis Added moment to handle, no significant change in tipping problem With a 25 lb weight,](https://reader036.fdocuments.us/reader036/viewer/2022080915/56649d8b5503460f94a72d4d/html5/thumbnails/8.jpg)
Manufacturing – Final Product1,000-1,000,000 Units
• Type of manufacturing used– Handle bars: extrusion (hot)– Handles: injection molding– Curved stopper legs: permanent mold casting– Pins/Bolts: permanent mold casting– Lever bars: extrusion (hot)– Lever handles: injection molding– Linkage rods: extrusion (hot)– Lever/handle brackets: permanent mold
casting/machining/welding