CENTRAL UNIVERSITY OF RAJASTHAN(Established by an Act of Parliament, the Central Universities Act 2009)

Bandarsindri, – 305801 Distt.: Ajmer,Rajasthan.

(Notice Inviting Tender) Dated:-14-11-2013

Sealed tenders are invited from original equipment manufacturers or their authorized Indian agents in two parts, “Part A” (Technical Bid) and “Part B” (Commercial/Financial Bid) with the following Details:

S. No. Name of Equipment Specifications Amount of E.M.D. (Rs.)1. Horizontal gel electrophoresis Annexure 1 5400/-2. Vertical gel Electrophoresis. (Mini ) Annexure 2 11640/-3. Electrophoresis Power Supply (Universal) Annexure 3 10200/-4. Electrophoresis Power Supply (Basic) Annexure 4 4056/-5. Digital pH Meter (3 point calibration) Annexure 5 1200/-6. Digital pH Meter (5 point calibration) Annexure 6 2100/-7. 2D Electrophoresis ( Isoelectric focusing) Annexure 7 64000/-8. Western Blot Unit Annexure 8 2800/-9. Multiscan spectrophotometer Annexure 9 30000/-10. ELISA Reader Annexure 10 8000/-11. Multiscan Go spectrophotometer Annexure 11 10000/-12. UV-Visible Spectroscopy with peltier Annexure 12 24000/-13. Vortex mixer Annexure 13 900/-14. Vortex shaker (simple) Annexure 14 6400/-15. Balance (Digital)- 4 decimal point Annexure 15 5100/-16. Balance (Digital)- 2 decimal point Annexure 16 2100/-17. Magnetic Stirrer (With Hot Plate) Annexure 17 3500/-18. Magnetic Stirrer (Without Hot Plate) Annexure 18 6500/-19. Digital Hot Plate Annexure 19 520/-20. Microwave oven Annexure 20 800/-21. Centrifuge Type-I Annexure 21 20000/-22. Centrifuge Type-II Annexure 22 10000/-23. Mini Centrifuge Refrigerated Annexure 23 8000/-24. Ultra Centrifuge (Ultra speed) Annexure 24 40000/-25. Fixed speed microcentrifuge 6000 Annexure 25 1800/-26. Fixed speed microcentrifuge 10000 Annexure 26 1800/-27. Variable speed microcentrifuge 10000 Annexure 27 3600/-28. Incubator CO2 with gas exchange Annexure 28 36000/-29. BOD Incubator Annexure 29 2000/-30. Incubator 37 degree for BSL II Annexure 30 2000/-31. Hybridization incubator double walled Annexure 31 4000/-32. Orbital Incubator With Shaker Annexure 32 42000/-33. Hot air oven autotime controller Annexure 33 8000/-34. Water Bath Temperature Controller Annexure 34 1000/-35. Circulating water bath Annexure 35 1000/-36. Multichamber water bath Annexure 36 1300/-37. Refrigerator 4 degree Annexure 37 4000/-38. Refrigerator glassdoor Annexure 38 1800/-39. Deep Freezer -20 Annexure 39 12000/-40. Deep Freezer -80 with CO2 backup Annexure 40 28000/-41. Deep Freezer -150 with LN2 backup Annexure 41 20000/-42. PCR-Gradient PCR (3 blocks) Annexure 42 6000/-43. Real time PCR Annexure 43 26000/-44. Homogenizer Annexure 44 8000/-45. Sonicator Annexure 45 5000/-46. Dry Bath Annexure 46 1840/-47. Rocker Annexure 47 2400/-

48. Autoclave Vertical Annexure 48 24600/-49. Autoclave Vertical for Biosafety level II Annexure 49 8200/-50. CD with fluorescence and N2 generator Annexure 50 136000/-51. Pipettes All Range Set (4 pipettes) Annexure 51 9000/-52. Multichannel Pipettes Annexure 52 2700/-53. UV-Trans- illuminator Annexure 53 3600/-54. Compound Microscope Annexure 54 10000/-55. Inverted Microscope Annexure 55 10000/-56. Pipette Aid Annexure 56 3000/-57. Laminar Flow BSL-1 Annexure 57 6000/-58. Laminar Flow BSL-2 Annexure 58 12000/-59. Ice Machine Annexure 59 22200/-60. Gel Documentation system Annexure 60 24000/-61. Thermo shaker ( Mixer) Annexure 61 2800/-62. Plant growth chamber Annexure 62 28000/-63. Mini cooler cell home Annexure 63 900/-64. Tissue culture rack Annexure 64 6000/-65. DGGE Annexure 65 12000/-66. Peristaltic pump 8 channel Annexure 66 6000/-67. Anaerobic chamber with gas supply Annexure 67 14000/-68. HPLC Annexure 68 32000/-69. Petri-rotator Annexure 69 300/-70. Rotavac Annexure 70 7000/-71. Gas Chromatography Annexure 71 30000/-72. Fermentor 3 Litres Annexure 72 24000/-73. Blender Annexure 73 300/-74. Paper chromatography cabinet Annexure 74 500/-75. Dual beam spectrophotometer Annexure 75 7000/-76. FTIR Annexure 76 20000/-77. Blot Scanner Annexure 77 6000/-

Cost of Tender Form: Rs. 1,000 /- (Non–refundable)

Last Date & Time of submitting Tender Form: 03-12-2013 upto 14.30 hrs

Mode of EMD and Tender fee:Tenderers should make separate D.D. (one or more than one

D.D.) for each Tender fee and EMD and send it with below

supporting.

Important Notes to the Bidder:

1. Central University of Rajasthan, Bandarsindri, invites tenders under two-bids system

for supply, erection, installation and commissioning of various equipments at the

School of Life Sciences, Central University of Rajasthan as per specifications given in

the Annexure. Tender document can be downloaded from the University website at

URL Link: http://www.curaj.ac.in/tenders.html.

2. The bidders are requested to read the tender document carefully and ensure all the

compliance with instructions herein. Non-compliance of the instructions contained in

this document may disqualify the bidders from the tender exercise.

3. All offers should be written in the English and price should be written in both figures

and words. The offer should be typed or written in pen ink or ball pen. Offer in pencil

will be ignored. The tenderer shall certify that the rates being quoted are not higher

than those quoted for any Govt. Deptt. or Institution or DGS & D or any organization

and that if during the years at any time the tenderer has quoted rates lower than those

quoted against this tender, the University would be given the benefit of Lower rates

by the tenderer to the University. The relevant documents should be enclosed with

technical bid.

4. The prescribed tender documents should be submitted in one sealed envelope duly

superscribed with “Instruments &Laboratory Equipments for the School of Life

Sciences at Central University of Rajasthan at Bandarsindri, Ajmer (Rajasthan)”.This

sealed envelope should contain 3 sealed envelopes marked A, B, & C as prescribed as

under:

a) Envelope A containing tender form fee of Rs. 1000/- and the appropriate Earnest Money, both in the form of Demand Draft in favour of CENTRAL UNIVERSITY OF RAJASTHAN payable at Bandarsindri. Tender shall be rejected if the tender form fee and Earnest money D.D.’s are not found in proper order.

b) Envelop B containing the Technical Bid along with the supporting documents. (See Terms & Conditions for more details)

c) Envelop C containing the Financial Bid. (See Terms & Conditions for more details)

5. The complete tender document is to be signed with seal & is to be placed in the

separate envelope along with the necessary required documents.

6. The duly constituted committee appointed by the competent authority of Central

University of Rajasthan, Bandarsindri, reserves the right to select certain items (in

single or multiple units) and reject the others or all mentioned in the Schedule. The

same committee will also reserve the right to revise or alter the specifications before

acceptance of any tender with prior notice on the University website.

7. Incomplete tenders, amendments and additions to tender after opening or late tenders

are liable to be ignored, and rejected.

8. The Bid shall be treated as a 2 Bid System. The Technical Bid shall be opened for

applicants whose earnest money is found in order. Financial Bid shall be opened for

those bidders who have qualified in Technical Evaluation.

9. Interested Bidders may obtain further information from the office of the Stores &

Purchase officer, Central University of Rajasthan, India.

10. All the pages of the tender document should be submitted altogether. Tenders shall be

submitted in 2 different parts (in a sealed envelope). Part Acontaining DD for tender

fee, Earnest money & Technical Bid document and Part B should contain

Commercial/ Finance bid. The two separately sealed and duly super scribed envelope

shall then be sealed separately in another envelop which shall be duly superscribed

with name of the equipment, due date& time as mentioned above. The tender

document should be sent to:

Central University of Rajasthan

N.H.-8 Road, Jaipur-Ajmer Highway,

Bandarsindri, Kishangarh,Distt. Ajmer,

Rajasthan

Pin-Code- 305802

All bids must be delivered to the above office up to the date and time indicated above. Bids

will be opened in the presence of Bidders’ authorized representatives who choose to attend on

the specified date and time. In the event of the date specified for bid receipt and opening

being declared as a closed holiday for purchaser’s office, the due date for submission of bids

and opening of bids will be next working day or as announced by the University in the

appropriate manner.

Any clarification regarding tender before submission of tender document can be

discussed with Prof. A.K. Gupta -01463 238559 or Finance Officer 01463 238724.

Please Note that the tender document is subjected to verification with the original tender

document, and if any discrepancy is found, the tender would be rejected. Tenders (Technical

Bid) will be opened first in the presence of the attending vendors.

Registrar

CENTRAL UNIVERSITY OF RAJASTHAN

Bandarsindri, Rajasthan

CENTRAL UNIVERSITY OF RAJASTHAN

(To Be Filled By the Vendor/ Bidder)

1. Nature of the Equipment/Instrument:

2. Name of the Vendor:

3. Full Address of the Vendor:

4. Telephone/ Mobile No.

5. Fax. No. (If any)

6. Details of the D.D.

a. For Tender Fee(Non Refundable) : D.D. No.____________ dated

____________ drawn from the bank______________________

b. for E.M.D Amount (Refundable): D.D. No.____________ dated

____________ drawn from the bank______________________

Seal and Signature of the bidder/Vendor

Central University of Rajasthan

TERMS AND CONDITIONS OF THE TENDER

1) Price / Taxes: Prices stated in this tender are firm and shall remain firm until required deliveries have been completed unless otherwise expressly agreed to in writing by both parties.  The vendor agrees that any price reduction made with respect to Material covered by this order subsequent to placement will be applied to the order. All prices specified herein include all charges for, but not limited to, inspection, and packaging.  Prices set forth shall be inclusive of applicable taxes viz sales, value-added or similar taxes until and unless specified in the schedule. This University in registered with DSIR vide No.TU/V/RG-CDE(1115)/2010 dated 23 March 2010 & is exempted for paying excise & Custom Duty.

2) Acknowledgement And Acceptance of agreement :  This agreement constitutes an offer from the university and is expressly limited to the Terms and Conditions contained herein.  The Terms and Conditions of the agreement are those that apply to the purchase of materials, items, products, components or services (hereinafter referred to as "Material"). All exhibits, attachments, technical specifications, drawings, notes, instructions, or information referred in the agreement are incorporated herein by reference.

3) The Vendor as an Independent Contractor : The Vendor shall perform the obligations of this order as an independent contractor and under no circumstances shall it be considered an agent or employee of the university.  The terms and conditions of this order shall not, in any way, be construed as to create a partnership or any other kind of joint undertaking or venture between the parties hereto.  The Vendor expressly waives any and all rights which may or may not exist to claim any relief under the university's comprehensive insurance policy, worker's compensation or unemployment benefits.

4) Delivery :The equipments should the delivered of Central University of Rajasthan and within a

time period of 60 days from the date of LC opening and complete installation within 30 days after date of arrival on or in case of indigenous purchase supply should be made within 30 days & installation be completed within next 15days. If any material is not delivered by the date specified therein, the University reserves the right, without liability, to cancel the order for undelivered material not yet shipped or tendered, and to purchase the same from another vendor and to charge the defaulting Vendor for any loss incurred in this transaction. Any provisions thereof for delivery by instalment shall not be construed as obligatory unless agreed upon by both the parties.  The University shall have the right to refuse deliveries made more than one week in advance of any delivery schedule appearing in the order unless arrangements for such early delivery have been confirmed with the receiving party.

If the vendor is unable to complete performance at the time specified for delivery, by reason of strikes, labour disputes, riot, war fire or other causes beyond the Vendor’s reasonable

control, the university at its option, may elect to take delivery of material and to pay such proportion of the contract price as deemed reasonable by the university.

5) Reproduction of Documentation :The University shall have the right at no additional charge to use or incorporate all or portions of material found in the Vendor's literature and/or reproduce the Vendor's applicable literature such as operating and maintenance manuals, technical publications, prints, drawings, training manuals and other similar supporting documentation and sales literature.  The Vendor agrees to advise the University of any Updated Information relative to the foregoing literature and documentation with timely written notice.

6) Rescheduling  :The University may without liability at least seven days prior to the scheduled delivery date appearing on the order defer delivery on any or every item under said order by giving oral notice to the Vendor (confirmed in writing within seven working days) of any necessary rescheduling.

7) Shipping, Packaging and Labelling : All Material purchased hereunder must be packed and packaged to ensure its safe

delivery in accordance with good commercial practice and where incorporated, the University's packaging specification.

The Supplier shall provide such packing of the Goods as is required to prevent their damage or deterioration during transit to their final destination as indicated in the Contract. The packing shall be sufficient to withstand, without limitation, rough handling during transit and exposure to extreme temperatures, salt and precipitation during transit and open storage. Packing case size and weights shall take into consideration, where appropriate, the remoteness of the goods' final destination and the absence of heavy handling facilities at all points in transit, including the final destination.

The packing, marking and documentation within and outside the packages shall comply strictly with such special requirements as shall be provided for in the Contract including additional requirements, if any, specified in the contract and in any subsequent instructions ordered by the Purchaser.

It is the sole responsibility of the vendor to provide/replace the item/good if it is lost or broken during the shipping or transportation due to whatever may be the reason.

Vendor is responsible to ensure, by contacting the University, that the shipping has been properly done i.e., all the items/goods have properly reached the University.

8) Changes / Amendments : The University shall have the right at any time, by written notice, in the form of an amendment order, to make any changes it deems necessary, including, but not limited to, changes in specifications, design, delivery, testing methods, packing or destination.  If any such required changes cause an increase or decrease in the cost of or the time required for performance, an equitable adjustment shall be made in the contract price or delivery schedule, or both.  Any claim by the Vendor for adjustment under this clause shall be deemed waived unless asserted in writing within ten (10) days from receipt by the Vendor of notice of change (amendment order).  Price increase, extension of time for delivery and change in quantity shall not be binding on the University unless sufficiently justified by vendor and accepted by the university in a form of amendment/ Change Order issued and signed by the University.

9) Inspection And Acceptance :Material procured from vendor shall be inspected and tested by the University or its designee at vendors cost.  If deemed necessary by the University, the Vendor shall provide without charge, all reasonable facilities and assistance for such inspection and test. Any inspection records relating to Material covered by this agreement shall be made available to the University during the performance of the order.

If any Material covered by this agreement is defective or otherwise not conforming to the requirements of this agreement, the University may, by written notice to the Vendor:

(a) rescind the purchase/supply order as to such non-conforming Material; (b) accept such material at an equitable reduction in price; (c) reject such non-conforming material and require the delivery of suitable replacements (d) If the vendor fails to deliver suitable replacements promptly, the university, with notice of seven business days, may replace or correct such material and charge thevendor the additional cost occasioned thereby, or terminate this order for default. No inspection (including source inspection) test, approval (including design approval) or acceptance of material shall relieve the Vendor from responsibility for defects or other failures to meet the requirements of this order.  Rights granted to the University in this article entitled INSPECTION is in addition to any other rights or remedies provided elsewhere in this order or in Law.

10) Invoicing / Payments / Set-Offs : After each completion of supply/purchase order, the Vendor shall send duplicate invoices including item number to the University's concern Department.

Payment of invoice shall not constitute acceptance of Material ordered and shall be subject to appropriate adjustment, if the Vendor failed to meet the requirements of this agreement.  The University shall have right at any time to set-off any amounts due to the Vendor, (or any of its associated or affiliated companies) against any amounts owed by the university with respect to this agreement.

11) Terms of Payment and Conditions:

(A)For Indigenous/Indian equipments/stores on DDP Destination basis:-

80% of the total payment shall be released on submission of proof of delivery of complete equipments/stores (stores/consignee receipt), inspection report and on certification of satisfactory installation of the equipment at the consignee's premises and after "ensuring verification of the Performance Security" @ 5% of the Purchase Order value.

Balance 20% of the payment shall be released upon successful commissioning of the equipment and on production of the documents showing takeover of the equipment by the consignee, after ensuring that already furnished Performance Security is valid for a period of 60 days beyond the date of completion of all contractual obligations of the bidder / supplier including comprehensive maintenance warranty obligations.

(B) For Imported Equipments/ Stores:-

For Foreign/Principal suppliers of equipments/stores:-

For payment made through Letter of Credit (L/C)

An irrevocable letter of credit (L/C) for 100% of the value of the imported equipments/stores (excluding the value of the Indigenous / Indian equipments / stores, if any) shall be established on submission of the acknowledgement of the order by the successful bidder stating the country of origin and port of shipment, submission of Performance Security @ 5% of the Purchase Order value, four copies of the Proforma invoice and confirmed Letter of Credit (LC) opening details.

It shall be the responsibility of the bidder to ensure that all the requisite documents are provided to the purchaser including the Performance Security in original for appropriate denomination and period on priority basis, so as to ensure opening of LC on time.

Out of this, 80% of the value of the imported equipments/stores will be paid against inspection certificate (where applicable) and shipping documents to the Principal through L/C. Balance 20% will be released within 30 days after due certification by the Purchaser/Institute for successful commissioning of the equipments at the premises and also, after ensuring that the furnished Performance Security is valid for a period of 60 days beyond the date of completion of all contractual obligations of the bidder/supplier including comprehensive maintenance warranty obligations.

Price Fall Clause:-

If at any time prior to delivery of the equipments/stores, the bidder/supplier reduces the sale price of such equipments stores as covered under this tender enquiry, to any organization (including Central/State/Deemed university) at price lower than the price quoted under this contract, he shall forthwith reduce the price payable under this tender for the equipments/stores being supplied after the date of coming into force of such reduction, the price of equipments/stores shall stand corresponding reduced.

12) Selection of the Bidder:For the purpose of selection of the bidder, a two-stage bidding process will be followed. The response to the tender should be submitted in two parts viz. Technical Bid & Commercial Bid & must be submitted in separate sealed envelopes.

(a) Technical Bid:Technical bid should contain information regarding the business turnover, experience

and other details of the firm to judge the suitability of the bidder. Bidder must be proving the following documents:

a) Detailed firm & company details, copy of registrations must be enclosedb) Signed & Stamped compliance sheet of the technical specification of the offered

equipment with technical printed literature must be enclosed with the technical bid.c) Authorization letter from manufacturer in case of dealer/s for the said equipment

enclosed with technical bid in prescribed format (Annexure - XIV)d) Clientele list (List of the institutes/organizations, where the similar order has been

executed during the last three years) and work done list. Supporting documents (couple of orders without any alteration/modification, copies of installation report) must be enclosed

e) Performance Certificates from clientsf) Self-attached photocopy of annual turnover, IT clearance Certificate, Audited

Balance Sheet, etc.g) The bidder/OEM self-declaration stating that he/she is not banned/debarred or black

listed by any Central/State Govt. of India/PSU/Organizations/Institutes in India or abroad in prescribed format (Annexure - XV)

h) DD/ for EMD amounti) Tender form fee in case of website version.j) The form of the “Terms and Conditions” should be duly filled and signed by

authorized person.

It is only when the information about the company in technical bid is found satisfactory; the commercial part will be opened.

(b) Price Bid:

a) Commercial bid should contain price of the material required to be supplied as per Price Schedule "A" as supplied by the University along with the Tender form, duly filled and signed by the authorized person.

b) All costs should be given in figures and words. All the Govt. levies like sales tax, octroi, CD, and educational cess, service tax etc., if any, should be clearly and separately mentioned for each item or component. However, all taxes will be paid at actual rates applicable at the time of delivery.

c) The rates quoted should be applicable to educational institutions and any cost advantage received inlieu in thereof should be passed on to the University.

d) Prices shall not be subject to escalation of any naturee) Prices should be FOR – Central University of Rajasthan and supplier will be

responsible for custom clearance for forwarding the same up to university campus. Custom Duty, Custom clearance charges & local freight will be reimbursed on actual basis, after submission of the evidence in original. Bidder should note that this University in registered with DSIR vide No.TU/V/RG-CDE(1115)/2010 dated 23 March 2010 & is exempted for paying excise & Custom Duty.

Vendors should clearly mark on the both sealed envelopes “Tender For Instruments & Laboratory Equipments (Central University of Rajasthan) and “Commercial / Technical Bid” on the respective envelope at left corner.

While the above procedures lay down the overall guidelines, Central University of Rajasthan reserves the right to select the vendor based on other parameters at its discretion.

13) Delivery and Opening of Tender :All tender documents should be sent through courier, speed post, registered post or by person. Telegraphic / fax offer will not be considered and ignored straightway. All tender documents received after the specified date and time shall not be considered.

The completed tender should be delivered at the Inward Section of the Administrative building of the Central University of Rajasthan, Bandarsindri, Ajmer, Rajasthan on or before Date: 03-12-2013 upto 14.30 hrs

The Technical Bid will be opened on 03-12-2013 upto 16.00 hrs

14)

15)

Performance Security:On receipt of notification of award from the University, the successful Bidder shall furnish the performance security at 5% of the cost of the material ordered in the form of DD in favor of The Central University of Rajasthanor in the form of Bank Guarantee or in another form acceptable to the University. Failure of the successful bidder shall constitute sufficient grounds for the annulment of the award and forfeiture of the bid security, in which event the University may make the award to the next lowest evaluated bidder or call for new bids.

Rejection of Bids:

a) If bidders give wrong information in their bid, University reserves the right to reject such bids at any stage and forfeit the Earnest Money Deposit / Performance Bank Guarantee and cancel the order, if awarded.

b) Incomplete bids are liable to be rejected. c) If the technical offer contains any price information the offer will be summarily

rejected. d) Canvassing in any form in connection with the tender is strictly prohibited and the

bids submitted by the bidder who resort to canvassing are liable for rejection. e) Unsigned tenders/bids, unattested corrections and over writing by bidders are also

liable for rejection. f) The schedule for accepting the tenders shall be strictly followed- late tenders shall

not be accepted. g) Bids submitted without supporting documents as mentioned or required to submit

with bids are liable to be rejected. h) The Tenderers must confirm in their bid acceptance in full of the terms and

conditions in this enquiry. Any non-acceptance or deviations from the terms and conditions must be clearly brought out. However, tenderers must note carefully that any conditional offer or any deviation from the terms and conditions of this enquiry may render the quotation liable for rejection.

i) Each page of the tender document including all annexure duly stamped and signed by the bidder must be submitted along with the tender bid and tender should be page numbered.

16) Liquidated damages for delayed supply :If vendor fails to deliver any of or all products or does not perform the services within the period specified in the contract, the University reserves the right to, without prejudice to its other remedies under the contract, deduct from the bill, a sum equivalent to 1% of the price of undelivered stores at the agreed price for each week to maximum limit of 5% of the value of stores so undelivered. Once maximum is reached, the second party may consider termination of contract.

17) Assignment / Subcontracting /sublet :The Vendor shall not assign the order received, any rights under this agreement or to become due hereunder neither delegated nor subcontracted /sublet any obligations or work

hereunder without the prior written consent of the University. 

18) Cancellations : The University may cancel agreement entered with vendor in whole or in part, for no cause, upon written, FAX, or telex notice to the Vendor, effective when sent, provided such notice is sent at ten (10) days prior to the delivery date specified on the face of this order.

The University may cancel order in whole or in part at any time for cause by written, FAX, or e-mail notice to the Vendor, effective when sent, in the event that the Vendor:

(a) fails to comply with any term or condition of this order including, but not limited to, delivery terms; or

(b) appoints a receiver, liquidator or trustee in bankruptcy or other similar officer over any or all of its property or assets; or

(c) files a voluntary petition in bankruptcy; or

(d) has had filed against it an involuntary petition in bankruptcy which remains in effect for thirty (30) days; or

(e) voluntarily ceases trading; or

(f) merges with or is acquired by a third party; or

(g) Assigns any of its rights or obligations under the Order to a third party without the university’s advance written consent.

 Upon the occasion of any one of the aforesaid and in addition to any remedies which the university may have in Law or in Equity, the university may also cancel this order or any outstanding deliveries hereunder by notifying the Vendor in writing of such cancellation and the Vendor shall thereupon transfer title and deliver to the university such work in progress or completed material as may be requested by the university.  The University shall have no liability to the Vendor beyond payment of any balance owing for Material purchased hereunder and delivered to and accepted by the university prior to the Vendor’s receipt of the notice of termination, and for work in progress requested for delivery to the university.

19) Warranty :a) Three years onsite comprehensive warranty & additional 2 years AMC with the

statement of availability of spares for at least 5 years from the date of the installation of Goods against any manufacturing defects and also give the warranty declaration (Annexure – XVI) that everything to be supplied by us hereunder shall be free from all defects and faults in material, workmanship, transportation hazards, and shall be of the highest quality and material of the type ordered, shall be in full conformity with the specifications. During the warranty period, replacement of any part of equipment’s or rectification of defects of works will be free of cost.

b) After the warranty period is over, the instrument maintenance charges, terms and conditions for Annual Maintenance Contract (AMC) / Comprehensive Maintenance Contract (CMC) up to five years should be stated. The AMC / CMC charges will be included in computing the total cost of the equipment. It may be noted that the

AMC / CMC charges shall be considered along with the cost of equipment for the financial evaluation of the bids.

c) Any deviation in the material and the specifications from the accepted terms may liable to be rejected and the bidders need to supply all the goods in the specified form to the satisfaction / specifications specified in the order / contract and demonstrate at their own cost. The payments shall be made only after receiving the material in the required specifications and quality to the satisfaction of the University authorities.

d) Downtime: During warranty period not more than 5% downtime will be permissible. For downtime exceeding penalty equivalent to 0.50% of the F.O.B value of the equipment for every week or part thereof may be imposed. Downtime will be counted from the date and time of the filing of complaints within the business hours of the tenderer.

e) The Vendor warrants that any Material supplied hereunder shall conform to the generally recognized manufacturing and safety standards of the Vendor’s industry as per Indian Standard Institution (ISI) or similar standard. The Vendor’s specifications on performance as detailed in the Vendor’s brochures, sales literature and other specifications as may be available to the university.

f) In addition to any other express or implied warranties, the Vendor warrants that the material furnished pursuant to this order will be:

(i) Free from defects in design except to the extent that such items comply with detailed designs provided by the university; of merchantable quality and suitable for the purposes, if any, which are stated in the tender/quotation.

(ii) If any material covered by agreement is found not to be as warranted, the University may, by written notice to the Vendor:

(a) Reject such defective material and require the delivery of suitable replacements.(b) If the Vendor fails to deliver suitable replacements promptly, the University,

with notice of seven business days, may replace or correct such material and charge the Vendor the additional cost occasioned.

(c) Any items corrected or furnished in replacement are subject to all the provisions of this article entitled WARRANTIES to the same extent as items initially furnished or originally ordered.

(d) Free maintenance and service during warranty.(e) Regular upgrades to all software during the entire warranty period.(f) Vendor should provide a certificate that they will provide the spares in future at

least for ten years.(g) Vendor should provide insurance up to the delivery point (on-site and not up to

the nearest international airport) and until the time of installation.

20) This warranty provision shall survive any inspection, delivery, acceptance, payment, expiration or earlier termination of this order and such warranties shall be extended to the employees, students, and users of the material. Nothing herein, however, shall limit the University’s rights in law or equity for damages resulting from delivery of defective goods or damage caused during the delivery of goods or provision of services.

21)

22)

Rights granted to the University in this article entitled WARRANTIES are in addition to any other rights or remedies provided elsewhere in this order or in Law.

Consumables/spares: All hardware & software including drivers, device interface

23)

24)

cards/network adaptor card must be pre‐installed & pre configured in the computer

provided. Licensed version of system software like HPLC system software should be

provided in CD (with up‐gradable version).

Manual ‐ Hard copies of instruction/operation/service manuals should be supplied

List of important Consumable/ Spares and parts having sufficient shelf life for trouble free operation of three years should also be provided.

Shifting & Reinstallation:If required manufacturer has to take all the responsibilities for shifting and reinstallation of the equipment from the temporary building to permanent building. This responsibility has to be given in writing by the manufacturer. All terms and conditions remain same at permanent site. Also, the performance of the instrument should be reproducible after shifting. Vendor should also provide a list of instruments where the vendor has done re-installation of such equipments in the past. It should be quoted separately.Training/installation:

a) Installation testing: suppliers of the instrument must provide free installation, commissioning and testing of the equipment in the laboratory at the current temporary site and thereafter at permanent site.

b) Comprehensive training of faculty & staff after installation should be provided, wherever deemed appropriate and an update in every six months (3-4 days) for the first two years and every year (1 week) for the next three years.

c) On-site training to the graduate students after installation.

25) Patent Indemnity :

The Vendor shall have to indemnify, hold harmless and defend the University, its employees, and students with respect to all claims, suits, actions and proceedings of actual or alleged infringements of any Letter, Patent, Registered or Industrial Design, Trademark or Trade Name, Trade Secret, Copyright or other protected right in any country resulting from any sale, use or manufacture of any Material delivered hereunder and to pay and discharge all judgments, decrees, and awards rendered therein or by reason thereof and bear all expenses and legal fees (including the University’s) associated herewith.  The university reserves the right to be represented in any such action by its own counsel at its own expense.

26) Indemnity  :

The Vendor will indemnify, defend and hold the University, its and students harmless from any loss, expense, claim or damage including reasonable defence costs, arising from any claim or action based on any acts or omissions of the Vendor, its employees, servants, agents or subcontractors.  The University reserves the right to be represented in any such action by its own counsel at its own expense.

27) A.M.C.:

A separate annual maintenance contract will be executed after completion of the warranty period. On execution of the A.M.C. contract, performance security will be returned to the

first party.

28) Compliance with Laws:

After acceptance of tender, successful bidder shall have to comply with the requirements of all the existing laws. The Vendor shall also have to comply with the Fair Labour Standards Act and the Occupational Safety and Health Act, and all other applicable laws, ordinances, regulations and codes in the Vendor's performance hereunder.  The Vendor will have to indemnify and hold the University and its customers harmless from any loss or damage that may be sustained by the University, by reason of the Vendor's failure to comply with any laws, ordinance, regulations and codes.

29) Tenders received late, incomplete tenders and tenders not in conformity with our prescribed specifications, terms and conditions will be rejected. Central University of Rajasthanwill not be responsible for postal delay, non-receipt / non-delivery of tender documents or loss of documents in transit.

30) Law of the Contract:

The agreement entered with vendor shall be governed by and interpreted in accordance with the laws in existence and the Jurisdiction of Ajmer, Rajasthan.

31) Site preparation: The supplier shall inform the University about the site preparation, if any, needed for installation, immediately after receipt of the supply order. Suppliers must provide complete details regarding space and all infrastructural requirements needed for the equipment, which University should arrange before the arrival of equipment to ensure its early installation and smooth operation thereafter. The supplier may offer his advice and render assistance to University in the preparation of the site and other pre-installation requirements.

32) Rate quoted by vendor should be valid for at least six months from the date of receipt of quotation.

33) As far as possible, quotations should be given for goods of Indian manufacturer and foreign goods quoted and proposed to be supplied should be covered by normal input quota of the dealer. This University is exempted from payment of custom duty/excise duty. Certificate of the same will be provided by the University, if needed.

I/We have read all the enclosed Terms and Conditions carefully and ready to accept and according to that I/We are submitting herewith the tender.

Seal & Signature of Vendor

TECHNICAL SPECIFICATIONS SECTION

Technical Specifications: The tenderer shall meet the respective minimum technical specifications for the item that is being bid for. Any additional features or specifications in excess of these minimum specifications will be appreciated. A set of desired additional features are mentioned along with the minimum technical specifications, wherever appropriate.

I / We the undersigned am / are ready to supply & install the following instruments along with all other accessories complete as mentioned below with accepting the terms and conditions which are enclosed with this order form and quote for the same

The technical specifications for all the Instruments are being placed under this tender have been detailed in the following Annexure (one annexure for each Instrument / Equipment; this will also include all the components of a particular instrument / equipment that are being bid for).

Annexure – I

ITEM: Horizontal Electrophoresis

Quantity: 6 Nos.

Specifications:

Cell size (W x L x H)- 18 x 40.5 x 9.4 cm

Gel tray sizes (OD) (W x L)- 15 x 15 cm

Sample throughput :- 1-120

Base buffer volume- ~1 L

Bromophenol blue migration: - ~3.0 cm/hr (at 75 V).

UV-transparent gel trays with a fluorescent ruler.

A gel caster that allows tape-free casting of multiple gels and sizes simultaneously.

Easy-to-replace electrode assemblies.

Combs: Choice of both Fixed-height drop-in combs and adjustable-height combs

should be there.

Should be IEC 1010 (EN 61010) safety certified.

Should have clear plastic construction with safety lid and cables.

Annexure – 2

ITEM: Mini-Vertical Electrophoresis

Quantity: 6 Nos.

Specifications:

Easy to use 2 mini gels (8x7 cm) SDS PAGE or upgradable to 4 mini gels (8 X 7

Cm) simultaneously.

Flexible- Capable of running hand cast as well as precast gel.

Running and casting module should be different

Interchangeable module- Should be upgradeable/ capable of using blotting module to

do western blotting.

Grounded glass plates with permanently bonded spacers & Leak proof, tape free and

easy assembly

It should include 1.0 mm spacers & combs & short plates.

Annexure – 3

ITEM: Power Supply (Universal)

Quantity: 3 Nos.

Specifications: Output range

(programmable) 10–500 V, fully adjustable in 1 V steps

0.01– 2.5A, fully adjustable in 0.001A steps 500 W maximum

Type of output Constant voltage, constant current, or constant power with automatic crossover

Output terminals 4 pair recessed banana jacks floating in parallel

Timer 1–999 min, fully adjustable

Pause/resume run function

Yes

Display 128 x 64 pixel, backlit, graphics LCD

Operating conditions

0–40°C; 0–95% humidity in the absence of condensation

Safety compliance EN–61010

EMI Conforms to CE Standards for Emissions and Immunity class A, tested only at 230 V; TÜV EMC certification

Safety features No-load detection, sudden load change detection, overload/short circuit protection, input line protection, auto power-up after power failure

Input protection Fuse on both hot and neutral

Input power (actual)

220–240 VAC, 50 or 60 Hz, autoswitching

Dimensions 27.5 x 34 x 10 cm (W x D x H)

Weight 2.5 kg

Annexure – 4

ITEM: Power Supply (Basic)

Quantity: 3 Nos.

Voltage 0-500V Current 0-500m A Timer 1 min 24.00 H Display LCD 24x4 Characters Resolution 1 V, 1m A, 1min Out Puts 4 in parallel, 4 mm sockets Parameters Voltage, Current, Time Parameter Control Mode Manual Mode / Program Mode Memory Option 16 Different method Ambient Temperature 0-40 Deg C Relative Humidity 0-90%, non condensing Power Requirements 230 VAC 50/60 Hz Weight 2.5 kg Fuse 1A (Each)

Specifications:

Annexure – 5

ITEM: pH Meter Type-I

Quantity: 3 Nos.

Specifications:

Should have a multi-display on big LCD screen of size 40(H) x 105(W) mm pH range should be 0.00 – 14.00 with accuracy of +/-0.02 mV range should be +/-1999mV with accuracy of +/-0.2mV (-199.9 – 199.9mV) or+/-

2mV others mV resolution should be +/-0.1mV (-199.9 – 199.9mV) or +/- 1mV others Temperature Range should be 0 – 80°C, with accuracy of +/-0.5°C & resolution of

0.1°C Operating Temperature should be 0°C – 50°C, Humidity <80% Storage temperature should be -20°C – 60°C, Humidity <90% Automatic buffer recognition to avoid errors during calibration Maximum 3 point calibration Unit dimensions should be 317(L) x 168(W) x 58(H) mm Standard package should include Meter/USA Plug type adaptor/ Manual/ Probe/

Solution/ Cable/ Software CD/ Probe stand Hold function should be provided to freeze the records “Ready” icon should be provided on LCD to indicate whether the reading on machine

is stable or not Al least 99 memories with real time stamp & could be downloaded to PC using

RS232 output for analysis Automatic or manual temperature compensation should be allowed Analog output should be available for chart recorders

Annexure – 6

ITEM: pH Meter Type-II

Quantity: 3 Nos.

Specifications:

Should have a multi-display on big LCD screen of size 40(H) x 105(W) mm

pH range should be 0.00 – 14.00 with accuracy of +/-0.02

mV range should be +/-1999mV with accuracy of +/-0.2mV (-199.9 – 199.9mV) or+/- 2mV others

mV resolution should be +/-0.1mV (-199.9 – 199.9mV) or +/- 1mV others

Temperature Range should be 0 – 80°C, with accuracy of +/-0.5°C & resolution of 0.1°C

Operating Temperature should be 0°C – 50°C, Humidity <80%

Storage temperature should be -20°C – 60°C, Humidity <90%

Automatic buffer recognition to avoid errors during calibration

Maximum 5 point calibration

Unit dimensions should be 317(L) x 168(W) x 58(H) mm

Standard package should include Meter/USA Plug type adaptor/ Manual/ Probe/ Solution/ Cable/ Software CD/ Probe stand

Hold function should be provided to freeze the records

“Ready” icon should be provided on LCD to indicate whether the reading on machine is stable or not

Al least 99 memories with real time stamp & could be downloaded to PC using RS232 output for analysis

Automatic or manual temperature compensation should be allowed

Analog output should be available for chart recorders.

Annexure – 7

ITEM: 2 D Electrophoresis

QUANTITY: 2 Nos

Specifications:

A) 1st Dimension IEF System: System is a dedicated instrument for immobilized pH gradient isoelectric focusing,

control software driven system The unit should include compatible focusing tray which can accommodates from 1 to

12 regular strips for 7-24cm strips and is capable of running 1-12 strips simultaneously.

Compatible universal focusing & running tray which can accommodate 12 no’s of IPG strips of 7/11/13/18/24 cm should be included.

The platform for running the strips should be provided with gold- plated copper electrode area

The control software enables creation storage and editing of protocols. The software should be capable of controlling 4 units simultaneously and should record run parameters over time & present data as graphs & log file.

Integral 10000v power supply (in 10 volt step), peltier solid state control temperature (15- 31deg), 0-1.5mA (1uA/strip step)

The system should have oil free rehydration options and contain minimum 10 reswelling trays.

Re-swelling tray for accommodating 7-24 cm strips (1 to 12 in no) should be supplied with the system for performing re-hydration along with rehydration solution.

Electrodes, electrode wicks, paper bridges, cleaning solution and Foam padsreplacement.

The unit has a programmable controller to store up to 10 protocols. Each may include rehydration, temperature, and voltage limits in each step, voltage step or gradient, maximum current per strip.

Compatible with CyDye-labeled proteins and other light-sensitive stains Sample preparation kit and starter kit to be a part of the basic system. Unit has a RS232 port for hook up to a computer and/or printer. Unit has automatic voltage cut off when safety lid is open. Unit secures light protection during the run. Unit is certified to meet CE, UL and CSA safety standards

B) 2nd Dimension gel electrophoresis Standard vertical system Systems capable of performing second dimension separations for strips of size 24

& 13 cm. Two strips can be run simultaneously in 13cm while six strips can be run in 13cm can be used simultaneously.

Maintain temperature between 1 and 45 degree centigrade with built in heat exchanger and optional external temperature circulator for faster runs with high quality.

System can run up to four gels at the same time. Instrument includes accessories including 4 rectangular glass plates, 4 notched plates,

2 gel modules lid &lower buffer chamber, 1.0 mm thick 10 well combs, 2nos and 1.0 mm thick spacer sets, 2nos and two sets of 1.5mm thick spacers

C) Power Supply

Power supply capable of running 2 units and delivering up to 600volts, 400mA and 100 watts

Constant voltage, constant current andconstant power modes. Automated recovery after power failure

D) 2 D Gel Image Scanner

High sensitive flatbed scanner for all densitometry application, electrophoresis evaluation. OD linearity above 3.7 OD, Full 16-bit pixel depth for accurate quantitation.

Should have FireWire bus for hot-plugging and sharing between multiple computer Scanning Mode with Reflection & Transmission

E) Image analysis software

Imports 8-, 12-, and 16-bit grayscale TIFF images of any size. Image, rotation, flipping, and cropping Imaging software should be able to create new projects, folders and classes Quantitation of protein expressionvariations across gels or between different

gelpopulations. Software should be able to create scripts. One single file contains image, spots, data (.mel format) Intensity calibration from scatter plot of two gels Nondestructive cross matching A-B, B-C, A-C Spot matching by annotations Gels alignment on matches with transparency mode Possibility of using multiple references Computing of overlapping measures between classes Factorial analysis (correspondence), report, and 2-D graphs on groups Database searches on the World Wide Web for corresponding spot data, with Internet

querying facility. Software should be able to upgrade to DIGE enable software using co-detection

algorithm technique for 2 D DIGE analysis 2 D software should be license& having advance feature Compatible PC , Printer

F) Other requirements:

Immobiline Drystrip pH 3-10,7cm, IPG-Buffer, pH 3-10L,1ml, Immobiline Drystrip pH4-7,7cm, IPG-BUFFER, pH 4-7,1ml and Drystrip Cover Fluid, 1000ml, 2D clean-up Kit.

Annexure – 8

ITEM: Western Blot system

Quantity: 2 Nos.

Specifications:

Blotting instrument should includes base, 2 cassettes to hold 1–2 midi or up to 4 mini blotting sandwiches, blot roller, and starter consumable kit

Transfer time should be less than 4 minutes — transfer 1–4 mini gels or 1–2 midi gels in a single run

The starter system includes:

blotting instrument

2 blotting cassettes

Blot roller

Starter consumables of one year

Annexure -9

ITEM: UV-Visible Spectrophotometer

Quantity: 1

Specifications:

Optical system Double monochromator and double beam Wavelength range

(nm): 190-900 nm

Wavelength accuracy (nm):

+/- 0.2 nm

Wavelength Reproducibility:

+/- 0.2 nm

Spectral Bandwidth (nm):

0.20 to 4.00 nm

Photometric range 5.0 Abs Slew speed 3000 nm/min Stray Light (%T): 0.0005%

Photometric accuracy

+/- 0.002 Abs (0 to 0.5 abs) +/- 0.003 Abs (0.5 to 1 abs)

UV-Vis limiting resolution

<0.24nm

Photometric Noise (Abs, RMS):

At 0 Abs : 0.00005

Baseline stability +/-0.0003 Abs/hour Baseline Flatness +/-0.001Abs Properties Specifications required Photometric

display +/- 9.9999 Abs , %T +/-200.0

Peltier temperature control

4x4 position, Temp. : -10 to 100oC.

Measurement mode

Quantitative analysis, wavelength scan, time scan, fixed wavelength, Abs/ %T monitor

Data processing Peak picking, peak height, peak area, peak width, Derivatives, Smoothing, Data truncation, Arithmetic, Baseline correction, Subtraction, Kinetics, Thermal, DNA/RNA/protein/nucleic acid/enzymes quantitation ratio

Software Protein and DNA melting, Software for Thermodynamics parameters calculation

Cuvettes 4 pair (250ul)

UPS and Servo stabilizer

of suitable capacity

Computer, Printer and Cover

Suitable capacity and customized dust cover for instrument and PC

Annexure – 10

ITEM: ELISA Reader

Quantity: 1

Specifications:

It is a Filter based Microplate Photometer for both research and routine diagnostic

applications.

It provides a broad wavelength range of 340-850nm, in a 8 position filter wheel, for

all kind of routine and research applications, with 3 preinstalled filters405nm, 450nm

and 620nm, additional filters can be ordered separately. Half Bandwidth of filters 6-

9nm.

Fast and accurate measurements of 96 wells in less than 6seconds and 384 well plate

in 12seconds.

It provides 3 speed linear shaking as standard.

Optional model available which provides incubation from ambient upto50’C, along

with 384 well plate reading.

The instrument has inbuilt self diagnostics, which checks the instrument during start

up for the following: plate position, measurement stability ( such as lamp, filter and

optical system), incubation, electronic operation. Additionally the lamp is switched

off when not in use, prolonging the lifetime of the lamp.

Automatic calibration during each measurement guarantees stability of day to day

results.

The instrument can be run on standalone mode or PC control using most advanced

Skanit software which has a very user friendly GUI, which resembles very much like

MSOffice 2007 and is Windows Vista compatible.

The instrument is robot or automation compatible.

The instrument is as per European CE-IVD ( 98/79EC) directive.

The large color screen with High contrast color display (480X272 dots , with 256

colors).

‘Quick Keys’ allows instant access to most commonly used protocols.

The Internal software contains both quantitative and qualitative calculations for

single, dual and kinetic measurements.

The internal software can store upto 100assays and results can be saved onto USB

memory stick which can be transferred to a PC.

15 Visual, logical and intuitive Skanit software for instrument control and data

handling , and all kind of data reductions like blank subtraction, quantitative curve

fits, qualitative classifications, kinetic calculations, along with data reportingmakes I

easy and trouble free.

Light source is a Quartz Halogen lamp.

Read out range 0-6Abs. Linearity 0-3Abs +/-2% for both fast and normal mode.

Resolution 0.0001Abs and Accuracy at 405nm +/-1%, and Precision at 405nm :

CV<=0.2%

Communication: USB for Data Export, USB for Printer, USB for PC

Power Consumption:100W

Dimensions: 210mm(H) X 290mm(W) X 400mm(D)

Include Luminiscence, and Fluorescence reading.

Annexure – 11

ITEM: Multiscan Spectrophotometer

Quantity: 1 Nos.

Specifications:

Wavelength

The wavelength range is by tunable Monochromator from 200-1000nm in 1nm increments

The instrument is able to perform multiple wavelength measurements for each well.Plates & Cuvette

The instrument is able to take 96 and 384 well plates both lidded and not lidded plates.

The Cuvette holder in the instrument is able to use Standard, Micro, and Ultra-micro Cuvette and Hellma Tray cell.Sensitivity:

Plates:

The instrument has a linearity of 0-2.5Abs, 2% at 450nm with a 96 well plate The instrument has anaccuracy of 1.0% + 0.003 Abs (0 - 2.0 Abs) 2.0% (2.0 - 2.5 Abs) at 450nm. The instrument has a precision of SD <0.003 Abs or CV < 0.5% (Precision mode) SD < 0.003 Abs or CV < 1.0% (Fast mode) at 450nm

Cuvette:

The instrument has a linearity of 0-2.5Abs, 2% at 450nm The instrument has anaccuracy of 1.0% + 0.003 Abs (0 - 2.0 Abs) 2.0% (2.0 - 2.5 Abs) at 450nm. The instrument has a precision of SD < 0.003 Abs or CV < 0.5%

Readings:

The instrument is able to use both Cuvette and Microplate simultaneously The instrument has a fast reading speed. It is able to read a 96-well plate in ~6

seconds (A1 to A1). The instrument reads a ~384 well plate in 10 seconds. The instrument completes full spectrum scanning(200-1000nm in 1nm steps) of a

sample in ~ 10 seconds.Incubator:

The instrument has an onboard incubator with temperatures ranging from ambient + 4°C to + 45°C

Incubator design prevents condensation forming on the Microplate lid.Shaking:

The instrument onboard has linear shaking facility

The speed of shaking can be adjusted to low, medium or highOther features:

The instrument is compatible for automation purposes. The instrument has a power Save function for low energy consumption. The instrument meets RoHS (Restriction of Hazardous Substances) directive.

Internal Software:

The system has inbuilt internal software for the measurement of samples with Cuvette and plates.

The inbuilt software is able to perform all calculations and save the data within the system.

The data export can be done through USB device.Computer Controlled software:

The instrument has the ability to choose free selection of plates from any manufacturer.

Path length correction value is different for different solvents and can be determined separately for each solvent used.

The software is able to display the results in the table or list format The results can be exported in the excel or PDF format. The system should be supplied along with the U plate for the micro volume samples

16 or more at a time.Which is capable for low samplevolumes down to 2 μL. It is an idealtool for photometric DNA or RNAquantitation and purity analysis.

Annexure – 12

ITEM: Spectrophotometer with peltier

Quantity: 1

Specifications:

Microcell AFBG optics for outstanding light throughput for small volume cells

Up to 100 Hz data acquisition for single cell kinetics

Complete line of Peltier temperature control accessories ~ Adjustable cell holder for optimum cell positioning

Numerous accessories for liquid and solid sampling

Performance Verification and optional software and

documentation for regulated laboratories

Software Features:

Advanced Fixed wavelength analysis with graphical data display and user defined limits

Wavelength scanning application with advanced tools for peak analysis and spectral processing

Next-generation Quantification package makes quantitative analysis straightforward

Integrated calculations provide more data per measurement in Quant

Automated file export and e-mail

Seamless paper-based reporting with user defined parameters

Workbook and template scheme makes data organization easy

CUE software for customized user interface and workflows

Specifications Of 8 Cell Peltier System

Temperature range: 0 to 100°C, Temperature accuracy: ±0.1°C

Temperature reproducibility: ±0.05 °C

Sample Stirring speed: 250-2000 rpm,

~ Holds up to 8 cells standard 10 mm pathlength cells

Annexure – 13

ITEM: Vortex Mixer

Quantity: 3 Nos.

Specifications:

Speed 3000 rpm

Operation Touch mode / manual mode

Top platform Round

Cabinet MS powder coated

Operating voltage 220v ac@ 50 Hrtz

Annexure – 14

ITEM: Vortex Shaker

Quantity: 8 Nos.

Specifications:

Speed should be upto 3000rpm

Should be able to operate in both Touch mode & continuous mode.

Should be provided with multitube attachments, Plate attachment & cup-attachment.

MS powder coated cabinet to avoid decay of body.

Annexure – 15

ITEM: Balance Type-I

Quantity: 3 Nos.

Specifications:

Weighing Capacity : 220 g

Readability : 0.1 mg

Pan Size : ø 90mm

Repeatability : < + 0.1 mg

Linearity : < + 0.2 mg

Adaptation to Ambient conditions : By selection of 1 of 4 Optimized filter levels

Monolithic Technology based weigh cell for tolerating the fluctuation in Accuracy with variation in temperature at root level.

Built in motorized calibration weight for automatic internal calibration function via touch key.

Intelligent Calibration mode for both internal calibration as well as external Calibration

Other important features:

Rectangular all Glass Draft Shield opening from three sides

High Contrast Liquid Crystal Backlit Display

Stainless steel weighing pan with removable dust and spill rings

Hanger for below balance weighing

Application programs

Weighing In Percentage

Dynamic Weighing/Animal weighing

Counting

Net Total

Simple weight and mass unit conversion by toggling between two weight units from choice of many units

RS-232 interface port

AC Adapter

Both Side Tare Key

Overload protection

ISO/GLP compliant printing capability with optional Sartorius Printer

ISO 9001 certified

Annexure – 16

ITEM:Balance Type-II

Quantity:3 Nos.

Specifications:

Weighing Capacity : 220 g

Readability : 0.01 grams

Repeatability : < + 0.01 grams

Adaptation to Ambient conditions : By selection of 1 of 4 Optimized filter levels

Monolithic Technology based weigh cell for tolerating the fluctuation in Accuracy with variation in temperature at root level.

Built in motorized calibration weight for automatic internal calibration function via touch key.

Intelligent Calibration mode for both internal calibration as well as external Calibration

Other important features:

Rectangular all Glass Draft Shield opening from three sides

High Contrast Liquid Crystal Backlit Display

Stainless steel weighing pan with removable dust and spill rings

Hanger for below balance weighing

Application programs

Weighing In Percentage

Dynamic Weighing/Animal weighing

Counting

Net Total

Simple weight and mass unit conversion by toggling between two weight units from choice of many units.

Annexure – 17

ITEM: Magnetic Stirrer

Quantity: 5 Nos.

Specifications:

Capacity 2L

Speed 0~1250rpm

Temperature 0~300oC

Accuracy ±1oC ~±3oC

Top Plate Size (mm) 135 × 135

Panel Material Steel

Timer 999 minutes

Power Source 220V (50Hz)

Dimensions (mm) 230 × 180 × 120

Weight 2.7kg

Accessories required Stir bar, Temperature probe 

Automatic Temperature Control

Connecting the temperature sensor into the stirrer, so that it can measure temperature and control object temperature, the accuracy less than 1oC

Annexure – 18

ITEM: Magnetic Stirrer Multiposition

Quantity: 5 Nos.

Specifications:

Number of stirring positions 5

Stirring quantity max. per stirring position (H2O) 0.4 l

Stirring position distance 90 mm

Speed deviation of individual stirring positions 5 %

Stirring quantity max. (H2O) 2 l

Motor rating input 7.2 W

Motor rating output 1.8 W

Speed range 0 - 1100 rpm

Stirring bar length max. 30 mm

Heat output 175 W

Heating temperature range room temp. - 120 °C

Temperature medium max. (dep. on vessel) 70 °C

Heat control scale 1-10

Speed control scale 1-10

Temperature constancy in medium 2 ±K

Set-up plate material silicone

Set-up plate dimensions 120 x 450 mm

Dimensions (W x H x D) 138 x 65 x 552 mm

Weight 3 kg

Permissible ambient temperature 5 - 40 °C

Permissible relative humidity 80 %

Protection class according to DIN EN 60529 IP 42

RS 232 interface no

Analog output no

Voltage 230 / 115 / 100 V

Frequency 50/60 Hz

Power input 185 W

Annexure – 19

ITEM: Hot Plate

Quantity: 2 Nos.

Specifications:

Microprocessor-Based: Designed with high performance digital circuit and CPU

Stainless steel panel

Capacity – 2L

Plate size should be 135 × 135mm

Temperature range: 0 – 300°C

Digital Speed Control: The stirrer should be press-key designed to adjust speed, which prevent the stirring bar from stopping

The indicator should display the stirrer's motor speed.

Automatic Temperature Control: Connecting the temperature sensor into the stirrer, so that it can measure temperature and control object temperature, the accuracy should be 1°C

Accessories to be Supplied: Temperature probe 

Annexure - 20

ITEM: Microwave oven

Quantity: 4Nos

Specifications:

Mechanical Control Powder Coated Cavity 20 Litres Capacity 4 Power Levels Defrost Feature 1200 W Consumption

Annexure – 21

ITEM: Refrigerated Centrifuge

Quantity: 2 Nos.

Specifications:

The centrifuge must offer at least 3 swingout rotor configurations and various angle

rotors to meet current and future sample processing needs of the lab.

Angle rotors must be manufactured from a highly corrosion and fatigue resistant

material

The buckets and rotor sealing lids must be certified for bio-containment by a 3rd party

lab of worldwide recognition.

Bucket lids must operate in a safe manner without spring clips or metal components.

The centrifuge must be capable of running up to 76 x 5ml or 7ml blood collection

tubes and 56 x 10ml blood collection tubes in certified sealed conditions.

The centrifuge must be capable of running up to 16 x 50ml or 36 x 15 ml disposable

conical tubes.

The centrifuge must be capable of running up to 4 x 400ml bottles in swingout

configuration and in certified sealed conditions

The centrifuge must be capable of running a minimum of 6 x 94-85 ml disposable

tubes at speeds of at least 18500 xg

The centrifuge must be capable of running at least 8 x 50 ml disposable conical tubes

in individually sealed vessels, certified for bio-containment

The centrifuge must be capable of running at least 30 x 15 ml disposable conical tubes

in fixed angle configuration

The centrifuge must be capable of running a minimum of 30 x 2 ml disposable

microtubes at speeds of at least 25000 xg in certified sealed conditions

The centrifuge must be capable of running a minimum of 6 microplates of standard

footprint and height; the rotor must offer the possibility to accommodate the microplates

in removable sealed containers, certified for bio-containment

The centrifuge must have a sealed swingout rotor capable of spinning samples above

5000 xg.

The centrifuge must have a low profile (not to exceed 14.2”/36cm) for easy access by

end-user

The centrifuge must not require bolting to laboratory benching to meet CE, CSA or

UL, IVD approved requirements for safety containment in case of rotor accident

The centrifuge must have a minimum of 6 “direct recall” program keys

The centrifuge must have an option for automatic lid opening at the end of the run

The rotor shall be installed and removed with no tool in less than 5 seconds.

The centrifuge must be able to display messages in at least 5 languages.

Centrifuge should have advanced imbalance technology that adapts for specific rotors

The centrifuge supplied with the Fixed angle rotor 30x2ml along with the 100ml rotor

with 15ml and 50ml adaptor. Also suitable Servo stabilizer for running the machine.

Technical Standards: IEC 61010-1, IEC 61010-202, IEC 61010-2-101 230 V only:

EN 292, EN 61326, EN 55011B

Certifications: UL listed / CSA certified / CE marked / IVD compliant / Certified

Biosafety, RoHS compliant, WEE compliant

Oak Ridge high speed centrifuge tubes with sealing cap of capacity 10 ml, 16 ml,

30ml and 50ml should be provided according to number of available slots in rotor.

Accessory: Berangers balance to balance tubes with chemical weight box

Annexure- 22

Item: Refrigerated Centrifuge Type-II

Quantity: 1Nos

Specifications:

Universal laboratory centrifuge for swing-out and angle rotors

Spincontrol universal

Illuminated keys for start, stop , lid open.

For sedimentation up to 4X 100mL in swing out rotors or up to 20,000xg in angle rotors

Brushless drive practically maintenance free

Speed preselection up to 15,000rpm Low Speed operation from 100rpm possible

A magnetic rotor identification prevents rotors from overspeeding active rotor identification

Stainless steel bowl

Imbalance switch

No need to open the casing for emergency lid lock release

Easy lid opening due to pneumatic spring support

Window in the centrifuge lid for external speed control

Produced according to national and international safety regulations

Possibility of precooling the rotors during standstill refrigerant CFC free

Guaranteed 4oC at max speed with all rotors

Accessories:

0.2 mL PCR Rotor

1.5-2.0mL eppendorf Rotor

15mL conical tube Rotor

50mL conical tube Rotor

50mL round bottom tube Rotor

Annexure – 23

ITEM: Refrigerated Microfuge

Quantity: 2 Nos.

Specifications:

Maximum RCF 17,000xg

Maximum Speed above 13,200 RPM

Supplied with Rotor 24x1.5ml/2ml with click seal lid. The rotor should be tested and

approved by HPA, Porton Down, UK for Biocontainment.

Large LED display for Time, Speed and Temperature

Max Noise Level: 50 dBA

Temperature set range from minus 9 °C to plus 40°C

Accelaration/Deccelaration time 10Sec/12 Sec

Time set range 1 to 99 min, 1 min increments

Toggle between RPM and RCF.

Induction maintenance free rotor

Wide selection of following rotors for future upgrade

Dual Row rotor 18x2 plus 18x0.5ml for simultaneous run of two different volumes

without using adapters.

36x0.5ml rotor

PCR4x8 (32x0.2ml) rotor with Click seal Biocontainment lid.

PCR 8x8(64x0.2ml) rotor

Certifications CSA certified, CE marked, IVD compliant, Certified Biosafety

Technical Standards IEC 61010-1, IEC 61010-2, IEC 61010-020

Annexure – 24

ITEM: Ultracentrifuge

Quantity: 1 Nos.

Specifications:

Maximum Speed : 1,00,000rpm or more

Speed Control Accuracy : ± 10 rpm

Maximum RCF : 7,50,000xg or more

Maximum Capacity : 1.5 litre.

Tube range: 2 ml to 250 ml.

Set Temperature : 0 to 40deg C

Ambient Temperature : 10 to 35degC

Cooling System : CFC/HCFC free

Acceleration/Deceleration Profile : 10 or more

Programmability : 20 or more with step run facility

Power : 230/ 240 VAC, 50 Hz, 30A

Machine should have features like eye – balancing of samples, entry through keypad

& touch screen and user locking facility, delayed start, stop, dual display of RUN &

SET parameters, RPM/RCF mode, Run scheduling etc.

Machine should have flexibility to accept rotors of different makes. Fixed Angle

Rotors, with volumes 8 places of 38-40ml (50,000 rpm), 6 places of 12-15ml (65,000

rpm), 24 places of 1.5 ml (50,000 rpm) & 8 places of 100 ml (40,000 rpm). All these

rotors should be of Carbon Fiber only. Each to be supplied with tubes and caps along

with Tube Sealing device suitable for various applications.

System should be supplied with suitable servo stabilizer.

Annexure-25

ITEM: Mini Centrifuge

Centrifuge for Micro-filtrations and cell separation. The unit should have compact design and a small footprint which requires minimal bench space. A transparent cover allows for constant observation and it can be used for both micro centrifuge and PCR strip tubes.

Technical Data :

Capacity: 8 x 2.0 ml

Permitted density: 1.2 kg / dm3

Centrifugal acceleration: 2000 G

Max. kinetic energy: 20 Nm

Motor rating input/output: 12 / 8 W

Speed : 6000 rpm

Timer : 1 – 99 min

Timer display : 7 segment LED

Rotor exchange : without tool

Tools Include in Delivery : Rotor 8 x 1.5 / 2 ml Adapter 0.5 ml Rotor 4 x strip 8 x 0.2 ml

Special safety features :

The centrifuge will run only when the lid is closed & Lid can be opened easily at the push of a button

QUANTITY: 2 Nos

Specifications:

Annexure – 26

ITEM: Microcentrifuge 10000

Quantity: 2 Nos.

Specifications:

Maximum RPM should be 3,000 - 10,000rpm

Maximum RCF should be 1000 - 7500g

Rotor capacity should be 8 x 1.5ml/0.5ml/0.2ml tube (additional 0.5ml and 0.2ml tube

suit)

Should have a LED display the rolling speed and timing.

Timer range should be 5sec – 99min59sec

Noise level should be ≤55dB

Should be a small foot-print model of size 175x156x125 (mm)

Rotor should have a large radius with centrifugal force should be 1.5 times bigger than

ordinary 6-hole rotor at the same rolling speed.

Single handed-operation with the cover switch designed such that it automatically

bounce 95 degrees

The rotor should be clip-on fixed. It is very convenient for rotors exchanging and pick-

and-place.

Maintenance- free motor, long life and safe.

Annexure – 27

ITEM: Variable speed centrifuge

Quantity: 2 Nos.

Specifications:

Aluminium rotor for 8 and 12 places

Speed range 3000-16000rpm for 16K

G-force: 17602 g @ 16K

Speed/gravity force option display on the screen

Speed control resolution: ±100rpm

Timer set range: 0-99 mins

Max chamber temperature up during running: ≤Room temperature+15◦ C

Working noise: ≤64dB

Power consumption:300W

Annexure -28

ITEM: CO2 Incubator

QUANTITY: 3 Nos

Specifications:

CO2 sensor: Should have a combination of an infrared CO2 sensor and PID (Proportional, Integrated and Differential) control with Recovery time ≤ 3 minutes

Relative Humidity Control: Should have gentle air flow through duct, a removable water pan combined with an independent heater at the base of the incubator for maintaining humidity. Humidifying pan should be easily removable & should have an optical water level sensor to warn of a low water level.

Should have option for programmable decontamination with continuous UV sterilization of air & humidity source (UV lamp should be completely isolated from cell cultures, decontamination method should not trap contaminants inside the incubator or require temporary removal of any components)

Walls & shelves: Should be of copper-stainless steel alloy & should have the ability to kill mycoplasma

Interior chamber should have fully rounded corners Direct Heat & Air jacket system with three sources of heat – sides, door and independent

bottom heaters, all of which should be located outside the chamber Should have Low profile, stackable design Should have user friendly door-mounted control panel Interior Volume: Atleast170 L Temperature Range:5°C above ambient temperature to +50°C Temperature Uniformity:±0.25°C, Temperature Controllability:±0.1°C Chamber humidity: 95 ±5%RH CO2 range: 0 to 20%, CO2 controllability:±0.15% Alarm system:High/low temperature, CO2 level, door & UV lamp failure, independent

overheat protection Shelves: 4 Should have field reversible door 30mm diameter access ports Should have FDA 510(k) clearance

Annexure -29

ITEM: BOD INCUBATOR

QUANTITY: 1

Specifications:

Dimensions – inner 500 x 500 x 1000mm and outer 660 x 840 x 1750 mm(W x D x H).

Capacity - 250 to 300 lit. Temperature range – 0⁰C to 60⁰C.with accuracy ±0.1⁰C. and uniformity ±0.5 at

20⁰C. Controller – Microprocessor PID Multi-Function controller. Display- LCD back light PV & SV display for programmable PID model. Timer -- 99hrs 59 min/ continuous. Material – interior stainless steel ( SUS 304) and outer Epoxy powder coated steel. Door – inner tempered safety glass and outer silicone packing magnetic door. Shelves—Adjustable 3 or 5 shelves. Circulation fan—14 W x 3 EA. Compressor—1/3 HP Electric supply—220 V, 50Hz.

Annexure – 30

ITEM: Incubator 37 for BSL II

Quantity: 1

Specifications:

Gravity convection provides gentle air flow and minimal drying out

Temperature range from ambient +5° to 75°C

Corrosion-resistant stainless-steel chamber (1.4016 / AISI 430)

Intuitive user interface for setting temperature

Large, easy to read vacuum fluorescent display

Internal glass door allows sample viewing without impacting temperature

Exceptionally small footprint with following features

Rounded corners, Microprocessor control

Automatic over temperature alarm, Access port

Stackable

SS interior 1.4016

RS232 interface

Internal glass door

Easy calibration routine

Capacity 75 ltr or more

Convection technology Gravity convection

Temperature range °C ambient +5 °C to 75 °C

Spatial temperature deviation at 37 °C ± 0.6 °C

Temperature deviation over time at 37 °C ± 0.2 °C

Dimensions chamber, mm / in (W x H x D) 354 x 508 x 414 / 13.9 x 20.0 x 16.3

exterior1, mm / in (W x H x D) 530 x 720 x 565 / 20.9 x 28.3 x 22.2

Number of shelves supplied / max 2 / 13

Max. shelf load kg / lb 25 / 55

CE certified

Annexure – 31

ITEM: Hybridization Chamber

Quantity: 1 Nos.

Specifications:

Double walled having outer chamber of mild steel duly painted and inner of Stainless Steel

Temperature controlled through a Microprocessor Based PID Digital Temperature Indicator-cum-

Controller with an accuracy of +0.50C. Carrier to hold bottles (6No.s of Size : 60mm dia x 200mm depth). Carrier should rotate at a variable speed of 2 to 16 rpm. Viewing glass window in the door allows inspection of the specimen inside the

chamber (CE, ISO 9001:2008, ISO 18001:2007, ISO 14001:2004, ISO 13485:2003 & GMP

CERTIFIED)

Annexure – 32

ITEM: Incubator Shaker

Quantity: 1

Specifications:

Large Chamber to Accommodate Flasks Up To Six Liters

• Incubated model.

• Units to be stackable two high on the floor.

• Two adjustable-height shelves to provide added storage.

• Large viewing window and internal light offer sample visibility.

• View temperature, speed and time simultaneously on three individual displays.

Product Description:

• Corrosion-resistant stainless-steel chamber to accommodate a variety of 18 x 18 in. (45.7 x

45.7 cm) universal and dedicated platforms.

• Durable powder-coated, cold-rolled steel exterior construction.

• Electrical outlet inside chamber to provide power for safe operation of shakers, stirrers or

rotators.

Digital Operating System:

• Triple eccentric drive to handle heavy loads providing uniform agitation and continuous 24-

hour operation, even at high speeds.

• Monitor and control chamber temperature over complete range with ±0.1°C accuracy at

37°C.

• Variable speed control from 15 to 500 rpm.

• Continuous/timed operation from 0.1 hour to 999 hours or 0.1 minute to 999 minutes.

• To have View of speed, operating time and temperature simultaneously on three individual

LED displays.

• Visual/audible alarms to alert if temperature deviates ±1°C of set point.

• Shaker to shut down and give visual/audible alarms signal if unit operates ±10% of set

speed, preventing shaker from walking.

• Provision for User-adjustable speed calibration using a digital handheld tachometer, where

verification is required and protocols can be standardized.

• Unbalanced load sensor to stop platform motion when excess vibration is detected

visual/audible alarms signal until condition is corrected.

• Soft start feature is required to eliminate sudden starts and stops, splashing of vessel

contents or wetting of flask closure.

• To retain parameters during power failure and unit should restart automatically after power

is restored.

Safety:

• Over-temperature safety feature with independent thermostat to provide additional backup

by controlling heat if main temperature controller fails.

• Safety interlocks to stop shaking motion when the door is open.

• Should carry international warranty of Three year warranty on parts and one year on labor.

Accessories:

Should be provided with clamps/tube holders/trays as per application &

requirements).

Annexure – 33

ITEM: Hot Air Oven

Quantity: 2 Nos.

Specifications:

Annexure – 34

ITEM: Water Bath Type-I

Working size mm 450×350×450

Power 1200W

Power supply 220V 50Hz    /   110V 60Hz

Temp. range RT+10-200°C

Temp. resolution 0.1°C

Temp. fluctuation ±1°C

Package size cm 76×57×91

G .W.  kg 61

N.W. kg 46

Quantity: 1 Nos.

Specifications:

Machine should have 3-button operation with large, clearly legible LED display.

Machine should have temperature range 25⁰C to 100⁰C.

Machine should have cooling output kW 0.225 at 20⁰C.

Maximum pump pressure 0.2 bar. With pump flow rate 15 L/min.

Machine should have Bath volume 7.5 liter or more .

Machine should have temperature stability ±K 0.05.

Machine should have heater power 1.5 kW. With bath opening 165 x 190 mm.

All specification should mention in original printed catalog or website.

Annexure – 35

ITEM: Circulating water bath

Quantity: 1

Specifications:

Circulator to unify temperature inside

Accurate temperature control

With drainage stopcock for easy cleaning

PID controlled speed and temperature with LED digital display

Made with SUS 304 stainless steel body with powder coating

Should be provided with Gable cover

Capacity 10/20 Ltrs.

Temp. Range Amb.~100°C

Temp. Accuracy ± 0.1°C

Sensor PT-100Ω

Digital timer 999h 999min 999sec

Dimension Inner (mm) 295 x 235 x 150

Dimension Outer (mm) 340 x 305 x 280

Weight 7 kg

Power 220v 60Hz

Annexure – 36

ITEM: Multi-chambered Water Bath

Quantity: 1

Specifications:

Double walled with outer body made up of PCRC Sheet duly powder coated

Inner chamber and cover made up of Stainless Steel Sheet (SS 304 Grade).

Digitally controlled.

Temperature range from ambient +5ºC to 80ºC ±0.5ºC.

Internal Dimension 300×300×175 mm × 3 baths

Capacity 18 Ltrs. × 3 baths

Temperature Range Ambient +5ºC to 99ºC ±0.5ºC

Controller Microprocessor Based PID Digital Temperature Indicator-cum-Controller

with an in-built Digital Timer. (Individual for each chamber)

Material of Bath Seamless Stainless Steel (SS-304)

Material Case Powder Coated Steel

Electric Supply 230V AC, 50/60 Hz

(CE, ISO 9001:2008, ISO 18001:2007, ISO 14001:2004, ISO 13485:2003 & GMP

CERTIFIED)

Annexure_37

ITEM: 4oC Refrigerator (Normal)

QUANTITY: 10 Nos

Specifications:

250 Litres Capacity

BEE Star Rating: 4 Stars

Colour: Silver Streak

Double Door

Transparent Interiors

100% CFC, HCFC and HFC Free

PolyBag Suspenders in the Freezer

Special Zinc Oxide Protection Fights Rust

Silver Ions in the Air Duct

Microbial Resistance in the Gasket

Low Starting Voltage of 130 Volts

Multiple Mini Utility Shelves in the Door

Twist and Serve Ice Trays

Toughened Glass Shelves

Jumbo Vegetable Tray

Humidity Jog Dial

Easily Removable Gasket

Snapdeal Code: SDL705846346

Annexure_38

Item: 4 Degree Freezer

Quantity = 3

The system should be VERTICAL standing. Volume (liters): Approximate 400 liters or more The system should have 7 Segment Electronic Control Unit. System should contain glass door. System should have forced air cooling system should have lock facility. System Should having automatic door closing System Should have Reversible door System should have adjustable shelves The temperature range should be between +1C to+ 8 C. The system should have CFC free refrigerants. The system should have minimum 5 freezer drawers for storage. The system should have individual freezing elements for each drawer. The system should supply with microprocessor controller and a built-in multi alarm

system. The height of the system should be adjustable. A stabilizer should be provided with the system. The system should be operable at 230V/ 50Hz. System should be CE ISO 9001.

Note: Each Firm/Company is requested to submit Brochure of the equipment with detailed specifications.

Annexure - 39

ITEM: Deep Freezer Minus 25oc

QUANTITY: 6 Nos

Specifications:

The Freezer must meet the following criteria: Freezer must have the exterior dimensions: 1745mm x 717mm x 710mm (H x W x D) Freezer must have the internal dimensions: 1205mm x 506mm x 505mm (H x W x D) Freezer must have (1) lockable insulated solid door Freezer must have a capacity of 276L Freezer must be manual defrost Freezer must carry a CE mark Freezer must have (4) casters standard Freezer must have (1) 25mm diameter access port located at the rear of the cabinet Freezer must use a (1) ¾ hp compressor Freezer must use R404a refrigerant Freezer must come standard with (4) baskets and (2) pull cover drawers Freezer must have a keyed on/off switch Freezer must have interior lighting with external on/off switch Freezer must have hasp standard for attachment of secondary lock Freezer must have digital temperature control with hi/lo audible and visual

temperature alarms Freezer must have compressor on/off indicator on control panel Freezer must have mute button for alarms Freezer must have low battery alarm Freezer must have rapid freeze feature for fast cool down Freezer must have ambient temperature display Freezer must be preset to -40°C Freezer should come with a certified & NIST/NABL traceable, Radio signal

Temperature meter whose display module can be kept upto 30 meters away from the freezer. Traceability certicate will help us in validating the temperature data.

- Freezer must use forced-air circulation to maintain internal conditions- Freezer must have a bottom mounted compressor

Annexure – 40

ITEM: Deep Freezer Minus 80o C

QUANTITY: 2 Nos

Specifications:

Must include NON-CFC REFRIGERANTS 23 cu. ft. capacity Upright, with (2) 1 horsepower compressors (990 is 120 Volt) Double Door access for product protection, with four inner doors New latch and handle for ergonomic handling and one hand operation Durable Stainless Steel interior with Inner doors. Down-feed evaporator, surge tank for extra capacity Adjustable solid Stainless Steel shelves Triple -sealing silicone door gasket 5” non-CFC foamed-in-place polyurethane insulation; 4.5” in door Two 10” tubeaxial fans to provide maximum cooling of the compressor housing Heavy-duty dual wheel swivel locking casters. Automatic voltage compensator responds to high and low voltages Powder coat paint for a durable surface Service valves provided to allow easy recovery of refrigerants and field servicing. Front to back airflow with Removable, cleanable air filter Hinged grill swings out for easy access to filter and battery A vacuum relief port allows easy re-entry after door openings 4” open x 12” long heavy duty hinge for ensuring positive closure and uninterrupted

service

TEMPERATURE CONTROL

The microprocessor controller must monitor in one degree C increments, with digital display.

Eye Level Information center for At-a-Glance Monitoring Temperature probe must be positioned to insure the alarm sounds before the stored

product can be affected by a rise in temperature. Battery back-up for the alarm monitoring system Both visual and audible alarms must alert operator of over and under temperature,

power fail, door ajar, and low battery conditions. Dry contacts included for connection to optional remote alarms. Optional eye level recorder mounted in the door or optional data logger

CERTIFICATIONS

UL Listed cUL CE Mark Manufactured by an ISO-9001 company

System should be supplied with CO2 backup system along with suitable cylinder regulator and Servo Stabliser.

Annexure -41

ITEM: Minus 152oC

QUANTITY: 2 Nos

Specifications:

Micro computer settable Temperature range: -125°C to -155°C (set by 1°C) Binary Cascade compressor (Hermetic type: 1100W) and sensor with Low side auto

cascade refrigeration system Capacity: 231 L (Internal dimension: 760x495x615 mm, External dimension:

1730x765x1010 mm) Pt1000 Temperature sensor Microprocessor temperature control LCD Display for temperature & time (graphic display of chamber temp. for 24h

should also be displayed on screen) Binary Mixed non-HCFC refrigerant (CFC Free) Exterior: Zinc galvanized steel with baked on Acrylic paint & Interior: Aluminum

plate One outer door with latch integrated lock, Monitoring hole Inner Door: 2 pcs (Plastic & Insulated) Double door gasket Alumite treated outer door latch Should have high efficiency oil separator that effectively separates lubricant oil from

refrigerant, Refrigerating oil: Ze-NIUS32SA, Oil Separator: SPK-OSO2S3 Vacuum Insulation Panels with densely packed, open cell foam insulation under

vacuum as well as rigid polyurethane foam insulation Evaporator: High stage side-Cascade compressor, Low stage side-tube on sheet Condenser: High stage side-Fin & Tube, Low stage side-Auto Cascade condenser Alarm lamp with intermittent buzzer sound (for Temp., Filter, Power failure) Remote alarm interface Microprocessor controlled Filter clogged check function Self-diagnostic function 2” boxes 1 access portAccessories (preffered):

LN2 Back up

Annexure -42

ITEM: PCR

QUANTITY: 3Nos

Specifications:

The system is a 96 well Thermal Cycler with block of 3 X 32, 0.2ml independent control.

The system could carry 3 experiments at once with three independently controlled blocks.

The system have Veriflex block and maintain 5C, 2 Veriflex zones in each block. Instrument has On board Tm calculator facility to approximate the optimal

annealing temperature. Instrument is Wi-fi – enabled and remote connected. Max Sample Block Ramp Rate :6 C/sec Temp. Accuracy = +0.25 degree C (35-99.9 degree C) Temp. Range = 0 to 99.9 degree C Temperature Uniformity = <0.5 degree C (20 sec. after reaching 95 degree C) PCR Volume Range = 10-80 ul System has flexible block configuration—accepts four types of thermal blocks for

optimization and throughput Display Interface : 8.4” color TFT LCD The machine is duly certified / authorized for PCR process and the vendor should

produce the certificate for the same. System should be supplied with the reagents for PCR mix of 500 Rxn. System should supplied with 3 year warranty.

Annexure: 43

Item: REAL TIME PCR SYSTEM

QUANTITY:1

Specifications:

The system should be an automated integrated system for both real-time PCR and post-PCR (end-point) analysis with following features :

Hardware :

The system should be 96-well Peltier based PCR machine.

The normalization of reaction due to non-PCR related fluctuations should be possible by using any calibrated dye.

The excitation source should be LED/Laser and the detection system should be photodiode/PMT.

The hardware must provide Peltier thermal cycling for Fast-PCR (40 cycles in less than 40 minutes) as well as Standard-PCR run in the same block.

The system should have temperature range of 4 0C-100 0C to facilitate incubation of samples at low temperature.

The system should have peak block ramp rate for heating as well as cooling exceeding 4.50C /second or more.

The instrument should have temperature range of 1-24 0C The instrument should come along with branded laptop for data analysis. System should support minimum reaction volume of 10 µL and thermal cycling

conditions to eliminate optimization of PCR conditions for running the templates from different sources simultaneously.

The system should have flexibility to run multi user samples with specific annealing temperature in a single run.

The system should have preferably Touch Screen LCD feature to avoid dependency on computer for operation. However, the system should come along with branded laptop for operation, analysis, net-working of multiple system and a USB port for data export to Power point, Excel or JPEG file formats.

A fluorometer for the precise quantitation of DNA, RNA and protein should be included in the supply.Software :

Dedicated licensed full version software for primer and probe design must be included in the supply.

The system should come along with licensed High Resolution Melting Curve Analysis software capable of having melt curve resolution of 0.1 0C. The vendor should have reagents for the HRM applications.

The instrument should have software that can analyze multiple perspectives in the Multiple Plots view, with side by side views of all data aspects including the amplification plots, standard curve, multi-component data plots, and raw data.

The system should along with software to support applications including absolute quantitation, Relative quantitation,multiplex-PCR, allelic discrimination (SNP), melt curve analysis as well as pathogen detection and plus/minus assay using internal positive control.

Supporting Chemistries and Applications :

The system should be completely open system to support all the Real Time PCR chemistry like TaqMan, SYBR Green, HybProbe, Molecular Beacons etc.

The system should be able to detect more than 6 colors and should be capable of doing multiplexing formore than threecolor.

The system should support applications including absolute quantitation, Relative quantitation, multiplex-PCR, allelic discrimination (SNP), melt curve analysis, High resolution melt(HRM) analysis as well as pathogen detection and plus/minus assay using internal positive control.

The system should be open system with flexibility to use micro well plates, individual tubes and 8-tube strips.

The instrument should have 9 logs of linear dynamic range. System should be standardized for Taqman and SYBR Green Chemistry with pre-

validated and functionally tested Taqman Assays for different applications like Gene Expression,SNP Genotyping,MicroRNA Expression,Viral Load analysis, Gene detection and Translocation Analysis. They should be readily available from the vendor.

The system should be supplied along with the fluorimeter required for the Quality of DNA, RNA and protein. All the products supplied are from one manufacturer only.

Terms &Conditions :

The instrument should come along with three years of warranty. The quoted system must have full license for PCR process. A copy of the license may

be attached to the offer. A compatible 2 KVA online UPS with 30 minute backup should be provided. The vendor should quote for the industry proven instrument having at least 30

installations. The user list for the same should be attached. The vendor supplying the instrument should have application support laboratory in

India, for efficient after sales service-support. Wet lab training for one person from the user lab at the supplier firm should be

provided. Firm MUST provide a compliance statement vis-à-vis specifications in a “tabular

form” clearly stating the compliance and giving justification, if any supported by technical literature with clear reference of page number, paragraph or lines. This statement must be signed, with the company seal, by the Tendered for its authenticity and acceptance that any incorrect or ambiguous information found submitted will result in disqualification of the Tender.

Annexure - 44

ITEM: HOMOZINIZER

QUANTITY: 1

Specifications:

Powerful dispersing instrument for volumes from 0.25 - 30 l (H2O) with digital speed display. It should offer a wide speed range from 500 - 10,000 rpm that enables users to work at high circumferential speeds even with small rotor diameters. A broad choice of dispersing elements guarantees a wide range of applications. Reproducible operations due to constant speed even with changes in viscosities. In addition, it should have digital speed display, electronic speed control, electronic overload protection, stainless steel dispersing elements can be cleaned quickly and easily, smooth start and error code display.

Accessories: Dispersing element, for lower volume, stirring shaft, high speed propeller, Jet mixer head, Cutting head, Stand, clamp and Strap

Technical Data:

Motor rating input [W] 1100 Motor rating output [W] 700 Volume range min. (H2O) [l] 0.25 Volume range max. (H2O) [l] 30 Viscosity max. [mPas] 5000 Speed range [rpm] 600 - 10000 Speed deviation [%] 1 Speed display LED Speed control stepless Noise without element [dB(A)] 72 Extension arm diameter [mm] 16 Extension arm length [mm] 220 Process type batch Dimensions (W x H x D) [mm] 115 x 355 x 139 Permissible ambient temperature [°C] 5 - 40 Permissible relative humidity [%] 80 Protection class according to DIN EN 60529 IP 20 RS 232 interface no USB interface no Analog output no Voltage [V] 220 - 240 / 100 - 120 Frequency [Hz] 50/60 Power input [W] 1100

Annexure – 45

ITEM: Sonicator (Probe Model)

Quantity: 2 Nos.

Specifications:

Ultrasonicator with 500 W or more for High Intensity Ultra Sonic Liquid Processor ,

250 ul to liters , and 20KHz

Ultrasonicator should have Automatic tuning, energy (joules),

It should monitor - digital wattmeter, temperature controller,

Equipment should have micro- processor - based, programmable, LCD screen

with user prompts,

Converter should be sealed and display real time,

Equipment should have 10 or more programs storage capability

Also, 10 hour process timer, variable amplitude control, full function pulser On

and off cycle.

It can control independently from .1 second to 10 seconds,

Equipment should have overload protection circuit, remote auction connector,

footswitch jack,

Standard probe ½” (13mm) or any other size with replaceable tip should come along

with ultrasonicator with quick disconnect converter

Equipment should be supplied with essential accessories and with required cable,

instruction manual. Tool Kit etc.

Assorted types probes and tips for different volumes.

Ultarsonicators should have sound abetting system to prevent ultrasonic waves.

Accessories like adjustable platform, chamber etc should be provided.

Annexure - 46

ITEM: Dry Block (DRY BATH)

Quantity: 4 Nos

Specifications:

Annexure - 47

ITEM: ROCKER

QUANTITY: 4 Nos

Specifications:

Digital rocking shaker with adjustable speed for smooth mixing tasks.For homogeneous mixing in flasks, culture flasks, Petri dishes and tubes. Even with load

Number of blocks 2

Heat output 250 W

Heating temperature range room temp. +5° - 120 °C

Heat control accuracy 1 ±K

Connection for ext. temperature sensor DIN 12 878

Temperature stability within the blocks at 37°C 0.5 ±°C

Temperature stability within the blocks at 60°C 1.5 ±°C

Set-up plate material Aluminium alloy

Set-up plate dimensions 96 x 152 mm

Fixed safety circuit 150 °C

Timer yes

Dimensions (W x H x D) 151 x 73 x 304 mm

Weight 1.3 kg

Permissible ambient temperature 5 - 40 °C

Permissible relative humidity 80 %

Protection class according to DIN EN 60529 IP 21

RS 232 interface no

USB interface no

Voltage 220 - 240 / 115 V

Frequency 50/60 Hz

Power input 250 W

and voltage fluctuations the shaking speed remains constant. An adjustable tilt angle ensures optimum adaption to the particular experimental conditions.

Timer: countdown, adjustable from 1 s to 99 h 59 min. Counter: display of shaking time. Error code display. Different attachments allow a variety of applications. Usable at 4 to 50 °C in incubators. Easy operation by foil keypad. Anti-slip rubber mat included. Suitable for continuous operation.

Technical Data: Type of movement: rocking Permissible shaking weight (incl. attachment): 2 kg Speed range: 0 to 80 min-1

Speed display: 7 segment LED Timer: yes Timer display: 7 segment LED Rocking angle adjustable: 2.5 to 15° Dimensions (W x H x D): 280 x 150 x 330 mm Weight: 2.2 kg Protection class acc. to DIN EN 60529: IP 21 Mains supply: 100 to 240 V, 50 / 60 Hz

Annexure – 48

ITEM: Autoclave Vertical

Quantity: 3 Nos.

Specifications:

Fully Loaded User Friendly Automatic Autoclave Inner chamber, outer chamber and support ring should be made of stainless steel (SS-

304 grade). Heaters cover stand and carrier/bucket should be made of Stainless Steel. Lid should be made of thick machined Stainless Steel plate (SS-304). Radial locking lid, Lid fitted with Pressure Gauge, Spring Loaded Safety Valve, extra

Safety Valve, Manual Exhaust Valve, Vacuum Breaker-cum-Purge Valve and water level indicator.

Drain Valve, Silicon Door gasket All internal joints should be argon arc welded, ground and polished µProcessor based Controller with time and temperature programmable by user. Class 'A' Platinum (Pt-100) sensor, enabling precise and accurate monitoring. Low water level alarm and cut off Sensor open alarm and display. End of cycle buzzer . Miniature Circuit Breaker Solenoid Valve for automatic purging and exhaust (user settable). Industrial grade energy efficient heaters Fully automatic model requiring no human intervention till a full sterilization cycle is

over. Should have a compact single box PLC with built in Human machine interface. 7 segment LED interface should have 3 displays (3+4+4) digit +5keys. Digital input 6 PNP-11 to 30VDC and analog input 2 CH-TC/RTD/0-10V/0-29 (User

selectable). 4 relay digital output and 1CH (0-10v)/0-20 ma Analogue output . Digital pressure indication and control through a microfused/ultrastable technology

based Stainless steel compound pressure transducer and a stainless steel Syphon. Standard Validation Port for external Multichannel Temperature Sensors / Scanners

for validation qualification and documentation purposes. Double Tier Password Data Security Lock for data security. Steam at 1340C for achieving sterility in three minutes High pressure sterilization at 1340C multiple/series of Steam pulses to be carried out,

through super smart PLC+HMI Chamber should be alternately pressurized and depressurized (maximum 3cycles) to

achieve a total sterile chamber ready to for actuation of main sterilization process. WITH CE, ISO 9001:2008, ISO 18001:2007, ISO 14001:2004, ISO 13485:2003 & GMPCERTIFICATES Communication Port should be available optionally through a RS-232 (Slave) or RS-

485(Slave) via Modbus-Rtu, complete with USB Communication Data Cable and single user software

Inner Dimensions 400×600mm Dimensions of Basket 375×450mm Capacity 78 ltrs

Heater Load 4.0 KW Sterilizing Pressure 1.2 kgf /cm² (15 psi) at 121ºC Operating Pressure Upto 30 Psi MOC (Pressure Vessel) Stainless Steel (SS-304) MOC (External Wall) Stainless Steel (SS-304) MOC (Top Lid) Stainless Steel (SS-304) Basket Stainless Steel (SS-304) Power Supply 220/230V AC, 50/60Hz

Annexure - 49

ITEM: Autoclave for BSL 2

QUANTITY: 1 Nos

Specifications:

Should Have Effective Capacity of 48Liters Should have stainless steel interior Should have temperature range of 105°C to 121°C Should have temperature gauge range of 80°C to 140°C Should have pressure range of 0-0.3 MPa/0-45Psi

Time setting range 1-180 mins Safety pressure release valve 200kpa Exhaust tank : 3L polyethylene Safety devices: pressure safety valve, Anti dry scorch thermo limiter, door switch,

handle switch, current fuse. Pressure valve should be designed at meet ASME Safety code Should comply with European Directives Should be ISO 9001, ISO 14001 and CE Certified

Annexure - 50

ITEM: Circular Dichroism Spectroscopy with Nitrogen gas generator

QUANTITY: 1

Specifications:

Light Source : >150W / 450W Water Cooled, Xenon lamp Measurement Wavelength Range :163-950nm (Standard), 163-1600nm ( Opt.Detector

) Wavelength Accuracy: ±0.1nm (163 to 250nm ), ±0.2nm (250 to 500nm ),

o ±0.5nm (500 to 800nm ) Wavelength repeatability: ±0.05nm ( at 163 to 500nm ), ±0.1nm ( at 500 to 800nm ), Wavelength resolution :- 0.025 nm

Spectral Band Width : 0.01 to 16nm Slit Width : 1 to 4000μm Stray Light : Less than 0.0003% (at 200nm ) Baseline Stability : +/-0.02m deg / hr Scanning modes: 3 modes, auto Scan, continuous Scan , step Scan. Scanning speed : 1nm to 10,000nm/min Data Integration Time : 0.1ms to 30s CD Full Scale : ±10m deg to ±8000m deg. CD Resolution : 0.00001m deg Detector: head-on photomultiplier tube Modulator : piezoelastic modulator RMS Noise: 185nm (0.004mdeg), 200nm (0.007mdeg), 500nm (0.007mdeg) UV Measurement : Photometric range : 0 to 5 Abs Photometric accuracy : ± 0.01 Abs Peltier Type CD / Fluorescence Attachment Temp Range: -10 to 1200C Variable speed magnetic stirring facility. Nitrogen purging inlet for sample purging as standard. Emission Monochromator Protein Secondary Structure Estimation Software Instrument communication : USB Shutter: computer controlled Data acquisition mode : four channels simultaneous Inbuilt Validation system to check the perforamnce of the equipment without any

additional tools. CD machine should have Alarm facility for light source over temperature, water leak

in sample compartment, nitrogen purge gas shortage etc. CD machine should be upgradeable in future for various attachment like Stopped

flow, Titrator, ORD, LD , FDCD,DRCD,Magnetic CD etc. Rectangular cuvette 1mm (1pair) or 2mm (2pair) or 10mm (1pair) path length with

Spacers. CD machine should have Peltier based Temp Cell Holder. Temp Range: 0 to 120oC

with stirrer facility. Quote a Nitrogen Generator with Purity 99.9% and flow Rate is upto-10 to 20L/Min PC with Laser Printer Installation & Warranty: Installation by the principal service engineers, Performance

demonstration and warranty for three years. Compliance statement highlighting above specifications. Optional 3 years AMC charges with each year differentiation must be quoted.

Annexure: 51

Item: Pipettes

Nos: 10 sets

Specifications:

Pipette should be light weight with high, robust and dependable.

Should have effortless one hand operation: volume locking, Pipette and tip ejection – all operations with the same hand

Easy maintenance: Dismantle and reassemble without any tools, all parts should be replaceable.

Material of construction: Corrosion resistant piston and sealing material, to allow uniform and smooth pipetting (SS piston for 0.1 to 20 µl, glass piston for 10 to 1000 µl, PTFE for 500 µl to 10 ml)

Sterilisation: Completely autoclavable at 121 C (20 min) without disassembly – for maximum protection from contaminations.

Calibration: Easy calibration technique – enables the user to calibrate and adjust the instrument in house without any tools. SOP for checking the volume can be provided.

Volume range: Complete range from 0.1 to 10 ml.

Identification: Individual serial number engraved on the instrument and also has individual labelling area for user specific identification.

Manuals: Each instrument must be provided with user manual which has pictorial description of all operations, limitations and functions.

Annexure: 52

Item: Multichannel Pipettes

Nos: 6 sets

Specifications:

Should be Light weight, Least RSI (Repetitive Strain Injury) Advanced volume gearing- Modular volume adjustment mechanism prevents sudden

change in the volume setting. Fully Autoclavable Separate soft touch tip ejector Ergonomic design In lab calibration and easy maintenance - Easy to open (No special tool required) Extremely light weight reduces the risk of Repetitive strain injury Super blow out piston with volumes of 50 ul and below volumes ensures delivery of

micro size drops.

Five years warranty with Online web registration Available in 12 channel.

Annexure – 53

ITEM: UV-Trans-illuminator

Quantity: 3 Nos.

Specifications:

Should have Ultra Safe UV blocking cover (with aluminum frame): block

99.99% UV transmittance

UV wavelength: 302nm (should be suitable for DNA & Protein fluorescence)

Detect unit of nucleic acid should be 0.1ng

Should have Adjustable intensity: from 100% down to 50%

Viewing area should be 210D x 260W (mm)

Should have 6 tubes of 8W each

Should have outer dimensions of 280D x 340W x 80H (mm)

Annexure - 54

ITEM: Upright Microscope

QUANTITY: 5 Nos

Specifications:

Upright microscope stand with LED illumination system for Bright field, Dark Field , Phase contrast with minimum 95,000 Hrs or more life time & should have facility of Automatic Light Intensity Adjustment.

Microscope should have Height adjustable focus knob facility & Corse / Medium / Fine focusing.

Microscope should have centrable condenser holder for vertical adjustment, right- and left-hand operation and clamp screw and focus drive coarse and fine with focus stop and focus knob coarse,

The aperture diaphragm’s scale (on the condenser) features color-coded markings, which correspond to the standardized color codes of the objectives. Standard condenser with color coding & with phase rings slots.

Microscope should have day light conversion filter), grey filter N16 and panchromatic green filter

Eyepiece 10x /20 & 5 hole objective turret and fully Glass made Objectives achomat 4x/0.10, 10x/0.25, 20x/0.40 , 40 x/0.65, 100x/1.25 oil.

Trinocular observation tube have 3 way light splitting facility 100: 50 :0 for attachment of camera.

Digital CMOS/CCD scientific camera for microscopy with software for measurement & analysis with scalable resolution up to 7 megapixel (3072 x 2304), pixel size 3.2um x 3.2um. with 12 FPS or more.

Image analysis: Software for analyzing and measuring the captured images ,linear distance etc.

Microscope, camera and software should be from the same manufacturer for optimum synchronization and reproducibility.

Branded Data Station (PC ) Compatible to Camera, software and Microscope for fast imaging.

Annexure - 55

ITEM: Inverted Microscope

QUANTITY: 1

Specifications:

Inverted Research microscope with facility of Bright field, Phase Contrast, upgradable to integrated Modulation contrast ( IMC ) technique also.

Harmonic Component System optics for balanced harmonization of all Optical system components, i.e. correction of all optical Components.

Should have the facility of nosepiece focusing. Inverted microscope stand for transmitted light including stage with 3 Position stages

support, coaxial double knob coarse and find focusing. Infinity optics with tube factor 1x, Port for exchangeable.

Transmitted light illumination with 5 watt LED Illumination lamp with ON/OFF with 50,000 hrs or more life time , switches No heat buildup, Auto Off function for illumination.

Quadruple objective nosepiece with 25mm thread size. Object guide for microscope stage with an adjustment range of (xy) of 128 x83 mm,

with special clamps for precise holding. Universal holding frame for Petri dishes. Slides. Binocular phototube with 45 deg. Viewing angle and having beam splitting positions

0/100%, 100/0%. Condenser with numerical aperture of 0.45 and long free working distance of 40mm. Objectives Long Working distance – Plan achromet 4x, 10x, 20x and 40x. Eyepiece 10x/20 BR Digital CMOS/CCD HD scientific camera for microscopy with software for

measurement & analysis with scalable resolution up to 7 megapixel (3072 x 2304), pixel size 3.2um x 3.2um. with 12 FPS or more.

Data Work station for documentation. The system like microscope, digital camera & software from the same manufacture

for better compatibility.

Annexure - 56

ITEM: Serological Pipette Filler

QUANTITY: 3 Nos

Specifications:

Should have large LCD Display Provides Visualization of remaining battery charge and speed settings

Should have 8 aspirations and 8 dispense (+ Gravity speeds) Should be lithium ion battery operated. Should have 15 hours continuous working between two charges Filter assembly 0.45 µ standard. Nosepiece of pipette holder should be Autoclavable silicon rubber Nosepiece can accommodate pipettes from 1- 100 ml.

Warranty should be one year. Should come with weighted table stand and a convenient wall- mountable holder. Should have the option of choosing from 5 different colours (red, green, white, clear,

blue).

Annexure - 57

ITEM: Vertical Laminar air flow.

QUANTITY: 2 Nos

Specifications:

Dimension inner- 1190 x 550 x 650 and outer 1350 x800 x1880 (W x D x H mm).with material interior stainless steel 304 and outer epoxy powder coated electro galvanized steel.

Filter replacement warning signal by pressure gauge & controller display with 9 stage velocity control, total using timer, UV/FL lamp ON/OFF.

Built –in mesh guard for protection. With one touch open front panel for easy maintenance.

HEPA filters class 100, purity 0.3µm partical removal 99.99%. Easyto replace filter from back panel with maintenance free design and structure.

Machine should have tempered safety glass sliding door. Machine should have prefilter 0.3 ~0.6 m/sec and noise level 56 ~60 dBA. Cabinet should one piece cabinet structure with air leak proof cabinet structure no

required separate stand. Machine should have air volume approximate 1350 m³ /h .

Annexure - 58

ITEM: Biosafety Cabinet

QUANTITY: 3Nos

Specifications:

The Bio safety cabinet should be Type A2 in which 70% Air should be re-circulated and 30% of the air should be exhausted

2. The motor must automatically adjust the airflow speed without the use of a damper to ensure continuous safe working conditions, even without maintenance adjustments.

3. In order to preserve safety to the user and the environment, the exhaust blower on the cabinet must continue operating when the supply blower stops working. If the exhaust blower should fail, the supply filter will also be turned off.

4. In order to ensure consistent and reliable down flow velocity across the supply HEPA filter over the life of the cabinet, the cabinet must use a pressure sensor (rather

than anemometer) to detect pressure drop across the supply filter, rather than in just one point across the down flow. The pressure sensor must be encased in order to protect the sensor from temperature, humidity and other environmental phenomena that can impact the sensor’s performance.

5. The microprocessor must display the inflow and down flow air velocities in real-time on an LED display to ensure the user knows whether or not the cabinet is working under safe operating conditions.

6. The front window must be a 10” sash opening and be made of laminated safety glass to ensure containment of potentially hazardous samples in the case of accidental glass breakage.

7. All interior and exterior parts must be painted or smooth to ensure no risk of cuts to users or maintenance personnel.

8. The front of the cabinet must be angled 10º to help minimize glare on the window to the user, and to ensure that the user’s posture is comfortable during a working session. Inadequate user ergonomics in a safety cabinet may lead to excessive fatigue, unsafe working habits and harmful consequences to user safety or product contamination.

9. The cabinet noise level must be less than 63 dB(A) for a 4 foot cabinet and less than 65 dB(A) for a 6 foot cabinet as measured in a sound proof room 12 inches in front of the cabinet and 15 inches above the work surface. Lower noise levels promote more comfortable and safer working habits of the user.

10. The Biosafety Cabinet should have microprocessor controller and same must be located on a slanted front panel so it is easy to see and reach from a seated working position in front of the cabinet.

11. The interior of the front window must be accessible for cleaning without requiring the user remove or support the window.

12.The interior walls of the cabinet must be coated in white color to ensure that samples are easier to visualize and enhance user comfort.

13. The biological safety cabinet must be capable of achieving current state-of-the-art in energy efficiency. A biological safety cabinet with lights on and fan at operating speed should consume less than 200 watts for a nominal four foot or 400 watts for a nominal six foot width and have a reduced energy mode for non-operational maintenance on containment in the work area.

14. The cabinet must automatically reduce fan/blower motor speed to 30% when the front window sash is in closed position to ensure reduced energy consumption when the cabinet is not is use.

15. In order to provide maximum effectiveness, efficiency and safety to laboratory Personnel, UV light must be programmable to allow for specific exposure times from 0 to 24 hours. The automatic shut off feature on the UV light saves money on replacement of the bulbs.

The Cabinet should be provided with taps for Vacuum, Water and Non Combustible Gas.

The Bio safety Cabinet should be NSF or EN certified. The Bio safety cabinet should incorporate HEPA or ULPA filter of the class H 14 EN

1822 or better and having efficiency of 99.995% at 0.3 µm particle size. Approximate Dimension Exterior 1500 H x 1300 W x 800 D; Interior 800 H x 1200

W x 500 D Ventilation System Exhaust and Inflow air volume approx 300-350 CFM Heat Emissions at 25ºC should be approx 0.2 KW or lesser. The Bidders should provide details of Standard Warranty available

The cabinet Should be provided with Microprocessor controller and large LED display for inflow and Down flow air velocity and hours of operation, Audible and visual Alarms for HEPA filter failure, blower failure, airflow speed failure, Incorrect window position.

The cabinet should be provided with fixed / adjustable Height Stand, UV Light and one set of preferably detachable arms rest and one / two electrical outlet.

Annexure - 59

ITEM: Ice Flaker

QUANTITY: 3 Nos

Specifications:

Ice Production Capacity : 200 Kg/24 Hrs Condensing Unit : Air Cooled

Storage D101 Bin Cap. : 100 Kg Power requirement : 220-240V/ 50 Hz/760W Insulatio

n : PUF Insulation

Compressor : Hermetically Sealed

Compressor

Refrigerant : R-404a, CFC Free

Bin Full : Auto Start/Stop

Control : Microprocessor Control

with LED

Indicator

Alarm Indications : Visual LED Drainag

e : Pipes Provided

Noise Level : Very Low Noise Level

Certification : ISO 9001 Certified

Annexure - 60

ITEM: GEL DOC System

QUANTITY: 2 Nos

Specifications:

System should have monochrome Scientific Grade CCD camera with real time and integration time, f/0.95.

System should have resolution of 5.5 Mega Pixels System should have Pixel depth of true 16 bit, should define 65536 Grey levels.

Scientific grade zoom lens Dark Room and Tran illuminator should have following feature:- It should be made from steel cabinet with epoxy painted body (chemical resistance),

should be completely light tight. Camera should be completely protected and covered to avoid any contamination from

dyes like EtBr etc. It should have Roll –out slide in Tran illuminator with UV blocking tray. Tran illuminator should have stainless steel frame to avoid any chemical resistance

and should be easy to clean. System should have UV security Switch and UV security timer. UV safety interlock: protects from UV exposure by shutting off UV light source when

door is open. UV Transilluminator should be microprocessor controlled, in case of excess heat

transilluminator should switch off automatically. Illumination modes: Trans UV, white light. System should have 3 position filter wheel Trans illuminator should have 312nm transilluminator, with dual intensity switch (6 X 8 watt). System should have Filter Size of at least 20 X 20cm System should have IP address for LAN network connection System should come with software for Real time mode GLP compliance Positive or negative image acquisition Grid display for easy horizontal and vertical gel positioning Pixel by pixel saturation warning display while acquiring the image. Gray scale monitoring while acquiring the image. User’s personal configuration file for easy saving and loading of his/her personal

image acquisition parameters. Printing on a thermal video printer or on the default desktop printer. Lane profile display Molecular weight or pH (IEF) value calculation Volume, ht and area calculation Colony counting Image enhancement etc Optional: With chemiluminiscence and fluorescence detection

Annexure - 61

ITEM: Thermomixer

QUANTITY: 2Nos

Specifications:

Temperature control range: From 15 °C below room temperature to 100 °C, minimum setting of 1 °C Mixing frequency: 300 - 3000 rpm (depends on the

SmartBlock used) Maximum Temperature Accuracy: ±0.5°C at 20-45°C Temperature Homogeneity: Max. ±0.5°C at 20-45°C Maximum Heating rate: 6 ° C / min Maximum Cooling rate: 2.5 ° C / min between 100° C and RT Mixing stroke in Φ : 3 mm Power supply: 220 - 240 V, 50 - 60 Hz Power requirement: 200 W Dimensions (W x D x H): 20.6 x 30.4 x 13.1 cm Weight of basic device: 6.2 Kg

Annexure - 62

ITEM: Plant growth chamber

QUANTITY: 1

Specifications:

Exterior Dimensions : 41”W x 32.5" D x 79.5” H(1040mm x 825mm x 2020mm)

Interior Dimensions : 37”W x 25" D x 54.5” H

(940mm x 635mm x 1385mm) Growth Volume : 35 Ft3 (1000 Litres) Exterior Finish : Powder Coated steel Interior finish : Stainless steel for scratch and corrosion resistance, long life and ease

of cleaning Cabinet Construction : CFC-Free Insulation Door : Flush, full width door with keyed lock with magnetic gaskets for positive

perimeter seal. Control panel with Instrument display : Located above the door Casters : Heavy duty swivel. Locking bolts are provided to secure the point. Temperature : +4C to +40C lights OFF and +10 to +45C lights ON Control : ±0.5°C at control point Humidity : Ultrasonic Humidifier - 90% RH – Limited by +24°C dew point at lights

OFF Condensing Unit : Cabinet is supplied with top mount air cooled condensing unit with

hot gas bypass system for continuous compressor operation, extended compressor life and close temperature control.ARABIDOPSIS CHAMBER KIT - A1000PGConstruction:

Tires/Shelves: One tired design, providing 5.65 ft3 (0.5m2) of growth area. Tires measuring 37"W x 22"D (940mm x 560mm) adjustable on 0.5"(12mm) Increments

Growth Height: 42" (1065mm) Each wire shelf supports upto 60lbs ( 27Kgs) of distributed load.

Lighting: @25 degree Celcius Programming and control: 3 level programming of lamps Intensity: 650 Micromoles/m2/sec intensity over each tire. Lamp Fixtures: 39W THO/840 fluorescent lamps Lamp Heat: removed by refrigeration System

Interior Conditioning: Distribution: Air is delivered upward

Annexure – 63

ITEM: Mini-Cooler cell home

Quantity: 2 Nos.

Specifications:

The device, in combination with a -80°C freezer or dry ice locker, should

provide the freezing rate of -1 degree per minute.

Should be able to accommodate at least 12 x 2ml

Should be ideal for cryo-preservation of most cultured cell lines.

The design should be a combination of insulation foam, radial symmetry, and a

heat transfer core to regulate heat loss rather than using a large thermal mass

(alcohol based freezer).

Should have low thermal mass, that will not cause a rise in local freezer

temperature and will protect nearby samples already stored in the freezer.

Annexure – 64

ITEM: Tissue Culture Rack

Quantity: 2 Nos.

Specifications:

ISO Cerified, D & B certified

Five Shelves fitted with 16 tubes, 8 bulbs, 4 UV and photo periodic timer

Mild Steel angle frame and shelves. Powder coated painting in corrosion resistant

paint.

Each Shelf 50”x18”, shelf to shelf distance 16”. Individual ON/OFF switch for each

shelf,

input 220-240V AC, 50Hz single phase,

working temperature 5°C to 45°C,

RH upto 90%.

Lockable castor wheel for easy mobility.

Annexure - 65

ITEM: DGGE System

QUANTITY: 1Nos

Specifications:

The DGGE (Denaturing Gradient Gel Electrophoresis) system should have the following specifications:

Temperature Range : 00C – 700C

Accurate temperature control (to within 0.1 °C) Gel Size : 28 x 18 cm Number of Vertical Gels Simultaneously run : 2 Maximum Number of Wells: 96 Combs: 20, 32, or 48 Well The electrophoresis cassette should use the U-shaped spacer to allow 100% leak free

casting of gels. There should to provision for connecting it to external chiller. Buffer flow in top compartment adjustable from outside Heating continues with lid open The system should use peristaltic pump to form the gels and supplied with peristaltic

pump. The system should come with software to design the primers. Electrophoresis voltage available with lid closed only Low level shut down of heating Non corroding titanium terminals; stronger platinum-iridium electrodes The system should be supplied with the power supply of the following rating :

400V, 50W 250mA,at 200V, 125mA at 400V-230V/50Hz 50W

Annexure - 66

ITEM: Peristalitic Pump

QUANTITY: 2 Nos

Specifications:

Flow rate: 0.3 µL/min to 30 mL/min (72 psi/5 bar/0.5 MPa max) Peristaltic tubing diameter: 0.25 to 4 mm (i.d.) Head speed:Continuous adjustment from 0 to 48 rpm by 0.01 rpm increments Pump head: 1, 2, 4 or 8 channel heads with 10 stainless steel rollers per

headRequired Pump head: R8 Eight Channel Head, Requires control module. All pump heads have SS Rollers

Tubing materials: PVC for most applications - Isoversinic® for chemical inertness - Silicone for biocompatibility - PharMed® for FDA and USP class 4

Motor speed stability:0.5% for any variation of line voltage - Torque or temperature Line voltage: 90V to 132V for 110 voltage selection: 180V to 264V for 220 voltage

selection Line frequency: 47 to 63 Hz Operating temperature: 0-40° C No warm-up time required Dimensions (w x h x d): 15 x 18 x 17.5 cm (5.0 x 7.1 x 6.9 in) Input/Output options: Contact closure: Two TTL-compatible inputs for control of

start/stop and direction of flow Voltage input: One 5V analog signal for variable control of motor speed Keypad functions: Start - Stop - Direction of flow - Increase and decrease flow –

Prime Required Connector kits: (1) Connector Kit for 1.0-1.65mm ID tubing (3mm max

OD), Set of 5o (2) Connector Kit for 2.0-2.3mm ID tubing (4mmmax

OD), Set of 5o (3) Connector Kit for 2.8-3.2mm ID tubing (5mmMax

OD), Set of 5

Annexure – 67

ITEM: ANAEROBIC CHAMBER

QUANTITY: 1 Nos

Specifications:

Complete anaerobic system providing the culture, work, and storage space Condensate-free stainless steel work chamber with adjustable shelves, electrical

receptacles, fluorescent lights, and a warm air jacketed incubator. Minimum Work space : 108.0cm x 38.1cm

Built-in 77.0 Ltrs. desiccation-free incubator that can be variably set from 4C above ambient to 70C (158F).

Centrally located oval glove ports for free access to all areas of the work chamber. Soft, clear vinyl front slopes gently for maximum visibility Control panel for automatic and manual control of the interchange auto-sequence,

indicator lights to monitor function status, and fixed and variable temperature control to regulate the incubator temperature.

Vacuum pump - 4 cfm capacity to 24 in. Hg Easily accessible palladium catalyst and desiccant wafers to maintain strict

anaerobiosis (less than 10 ppm O2). Charcoal wafer to remove hydrogen sulfide (H2S) and extends the life of the

palladium wafer. Auto-sequence cycle to completely automatically effect oxygen reduction of the

interchange atmosphere. Unit requires only anaerobic grade gas mixture and nitrogen. Full one year warranty on parts and labor System Should be supplied with required cylinder, regulator required to run the

system.

Annexure: 68

Item: HPLC

Quantity: 1

Specifications:

Module Specifications

1. Solvent delivery System, (High Pressure HPLC pump )-Two (2) numbers

Integrated High Pressure Binary Gradient System

Flow rate Range : 0.01ml/min – 20.0 ml/min or more

Operating pressure Maximum 6000 psi

Flow rate accuracy ± 1% or better at 1 ml/min

Flow rate precision RSD up to 0.1% at 1 ml/min

De-gasser Online / Offline degasser

2. Gradient Mixer Suitable for high pressure and low pressure applications

3. Auto injector

Injection volume range: 0.1 – 2000 µL

Injection-volume Reproducibility:

RSD up to 0.5% at 100 µl injection volume.

Injection Loop size: 50, 100/200 & 2000 µl Injection Loops (1 each)

Sample vials: Sample Rack for minimum 90 of 1.5/2.0 ml vials

Manual Injector A Rheodyne Manual Injector should be quoted along with the instrument.

4. PDA Detector

Wavelength Range : 190-800 nm or higher

Light Source Deuterium arc (D2) Lamp

Wavelength accuracy: ± 1 nm or better

Wavelength Repeatability ± 0.1nm

Baseline Noise level : <= 10 x 10-6 AU

Drift : <=1.0x10-3/Au/hr/Degree Celcius

Number of Diodes 512 or better

Flow Cell Design: Taper Slit Design

Flow Cell Volume 10ul or Less

Optical Resolution 1.2nm or better

5. Conductivity Detector

Conductivity Range 0 to 10000 uS/cmNoise Should be <0.005uS/cm

Drift Should be < 0.05uS/Hr/0C

Cell Volume 0.6µl

6.RI Detector:

Refractive Index Range: 1.0-1.75 RIU

Noise: Should be <± 1.5 * 10-9RIU

Drift: Should be <± 200* 10-9 RIU

Temperature Control: 30°Cto 55°C

Flow Cell Volume: 10µl

Light Source: LED

7. Column Oven

Temperature range Ambient to 60 °C or more

8. Software for data analysis Windows based chromatography software should provide complete control of HPLC system.

The raw data should be available for processing at any time after modification of ‘n’ number of times.

9.Installation and warranty Onsite installation at free of cost and 2 yr. comprehensive warranty after the date of installation should be provided.

10. Columns Column suitable for Anion Analysis & Reverse Phase C18 should be quoted along with the instrument.

OPTIONAL ITEM:

1. Data collection and storage device

Latest HP/DELL PC with TFT monitor and printer should be quoted along with the instrument.

2. Online UPS 2 KVA online UPS with minimum 60 mins backup and maintenance free battery – 1 no.

3. Columns Column Suitable for Fatty acid analysis, Sugar Analysis, & C8

Terms and Conditions:

1. FOR Destination only2. Clearance agent should be hired by the company3. University will provide Custom deduction certificate in advance

Annexure - 69

ITEM: Petri Rotator

QUANTITY: 1

Specification:

Variable rotational periods from 3 to 25 seconds

Variable rotational speed control: 9 to 110 rpm

Accommodates Petri dishes up to 103 mm diameter

IR sensor allows user to switch the turntable on and off at any time with simple movements of the hand. High performance device features timer and variable speed control (9 to 1100 rpm) to ensure uniform and individual inoculation of the Petri

dishes. In addition to 3 to 25 sec. variable rotational operation mode, a continuous rotational operation setting is for use when a longer operating period is required. Stainless steel unit is UV resistant and flame-sterilizable. Additional features include Function and Alarm LEDs, individual timer and speed control knobs and silicone-covered turntable (109 mm dia.). Dimensions W x H x D: 110 x 60 x 160 mm; Weight: 2.2 lbs.

Annexure - 70

ITEM: Rota Vapour , Vaccum Pump

QUANTITY: 1

Specifications:

Diagonal Condenser with normal glass. Motorized electronic quick action jack. In case of power failure, automatic lifting

of evaporation flask. Speed range : 20- 270 rpm or more. Patented combi clip for easy fixing & removal of vapour duct Evaporation flask holding capacity : 50 ml- 4000 ml.(can be mounted directly in

the vapour duct without any adapter.)

Seal made of PTFE composite material, one piece vapor duct. Effective cooling surface area > 1600 sq. cm. Optimized condenser , all connections (vacuum, water circulation etc) at the

lower part of condenser. Complete with 1litre receiving and 1 litre evaporating flask as standard. Operated on 220V-240V, 50/60 Hz.CE approval.

Heating bath:

Temp. range 20’C-180’C , Display of set and actual temperature with heating on-off. Bath capacity: 4 liters. Max. Flask holding capacity : 4 liters. Temp. locking facility in the heating bath. With integrated carrying handle. Infra red communication between the bath and rotary evaporator. Wireless contact on the heating bath for supply of power. Operated on 220V-240V, 50/60 Hz.CE approval.

VaccumController :

Integrated Vacuum Controller for display, adjustment & control of vacuum. Measurement range : 1400-0 mbar , Control range : 1100-1 mbar Timer function for process determination after pre specified time. In built solvent library with more than 40 preset solvent , which can be expanded

by the customer. CE approval.

Diaphragm Pump:

Speed controlled pump,PTFE with PEEK head. Final vacuum <10 mbar. Suction volume : 1.8 m3/hr, brushless DC motor, speed around 1600 rpm with sound absorber Integrated gas ballast , Visible diaphragm through transparent window head on both side. operated on 100-240 V, 50/60 Hz. CE approval.

Recirculating Chiller:

CFC free refrigeration. Temp. range : +10’C Flow rate : 2-3 litres/minute Cooling power : 400 W at 15’C Operated on 230V/ 50-60 Hz. CE approval. Spares : 01 no. vacuum seal ,01 no. stop cock , Evaporation flask 250 ml (01 no.)

100 ml (01 no), Receiving flask flask 250 ml (01 no.) 100 ml (01 no). Warrranty :24 months from installation date.

Annexure: 71

Item: GC System

Nos: 1

Specifications:

Temperature range: Ambient +4°C to 450°C and should be upgradable to -100°C with liquid N₂.

Temperature programmed ramps: 22 ramps or more having cool down rate less than 5 minute for GC oven Temperature of 400 – 50Degree C.

GC should have built in 10 or more method storage. The system must have auto injection facility on two injection ports , to be achieve by

one auto injector tower with 100 vials OR More with dual auto injection facility. System should be capable to install minimum 3 multiple injectors ( 2 Programmable

Temperature Capillary Injectors with provision t for fast cool down with Coolant & One Packed Column Injector With Wide bore column Connectivity) and 3 multiple

detectors ( FID,TCD, FPD/PFPD and ECD) of user choice irrespective of detector type apart from Mass detector.

It should have provision of EPC / EFC/PPC for all the pneumatic parameters with Pressure Range of 150 psi for use of wide variety of Capillary columns, Pressure Resolution of 0.001 psi which offers Retention Time Reproducibility of 0.0008 min & connectivity to Micro bore Capillary Column with id less than 0.10mm for Fast GC application.

Vendor to offer Direct Sample Probe for solid/Liquid samples as optional. It should be upgraded in future with HS, MS OR MS-MS etc.

INJECTORS:

Programmable type Temperature Vaporizing Capillary Injector QTY --- 02 Nos. Pressure range: 0-150 psiTemperature range: Ambient + 10 °C to 450 °C using air cooling & compatible for Liquid N2/Co2 connectivity.Maximum temperature ramp rate: 200 °C/minTemperature ramps/holds: 20/21 or more.

Packed Column Injector with Wide bore Capillary Column connectivity --- 01 No Pressure range: 0-150 psiMaximum temperature: 450 °C

Detectors:

TCD- Thermal conductivity Detector:Maximum Temperature: Better than 400 °CHigh sensitivity four filaments with Burn out Protection.

Accessoreis :Gas Purification PanelGas Cylinders2 Capillary Columns (30ml with 0.32 or 0.22 mm ID)PC and Printer (Dell make only)5 KVA line conditioner with surge suppressor.

Offer to be made for all required Pre requisites for complete working & Installation of GC System, Supplier to provide Details on Local items & Prerequisites offered separately in Indian Rupees.

Please quote prices of all items separately.

OptionalFID Flame Ionization Detector:Maximum temperature: 450 °CDetectivity: 2 pg C/sec or better

Linear dynamic range: 107 or betterOperational quality: Flame-out detection and Auto re-ignition

Note: GC should be upgradable for other detectors whenever needed.

Annexure: 72

Item: Specification for Microbial Fermentor

Quantity: 1

Specifications:

The system should be a compact autoclavable Fermentor of 3-4 liter total volume jacketed vessel designed for the growth of bacteria, yeast, and fungi.

The system should be suitable for high density microbial fermentation processes such as batch, fed-batch, and continuous process. All the accessories for Batch mode should be

quoted in main and accessories for fed-batch and continuous mode of fermentation should be quoted in optional.

The controller should have 16 or more control loops

Latest generation Microprocessor based Touch Screen Controller with self adaptive P.I.D. control and synoptic view.

Integrated Microprocessor based Programmable controller for pH, DO, Temperature, Foam level, and stirrer speed etc. with provision to display the process parameters on controller and on computer simultaneously

Desirable Feature: the controller with GAMP/cGMP compliant/guidelines will be preferred. This fact must be explicitly stated in the printed catalogue of the manufacturer a copy of which should be enclosed with the tender. Scada software should be quoted in optional.

Main Controller : body case with a bright color touch-screen display of minimum 10” for control of pH, DO, temperature agitation, peristaltic pump flow, mode of fermentation and for calibration etc

Type of Vessel: autoclavable vessel should have provision for pH, temperature, DO, sampling port and continuous culturing. The top plate for the vessel should have at least 16 or more ports

Total Volume : 3-4 liter total capacity, glass material, stainless steel dish-bottom heat exchanger or borosilicate jacketed vessel with temperature control via circulation of heated / cold water in jacket

Peristaltic Pumps: Pumps for acid, base, antifoam, and substrate feeding (3 Nos.) and it should be have option for other variable pumps also (At least two)

Thermal Mass Flow Controllers : Thermal Mass Flow Controllers (TMFC) with at least 3 gas control. Each gas must have its own/individual TMFC i.e., total 3 TMFCs (for air, O2, CO2, /N2)

Agitation System: With high performance DC motor. The agitation range and control should be from 50-1,000 RPM with 1 RPM increments

Baffle & Impellers : The system should be provided with 2 six bladed Ruston impellers and four 316L removable stainless steel baffles

Sparger & Condenser : Stainless steel condenser, mounted on the head plate and ring/L sparger

pH electrode : Gel pH probe with digital display in 0.01 increments. The pH ranges from 2-14 via PID control ±0.01 ph monitoring with digital display

DO electrode : Polaragraphic DO probe with digital display in 0.1% increments. The DO probe range and control should be from 0-200% (air) with digital display

Temperature range : 5-80ºC, ±0.1ºC (operating temperature at least 5ºC above the coolant to 80ºC)

Chiller : Suitable re-circulating, CFC-Free, Mobile Chiller (good brand), working temperature -20 to +40ºC (stability ±0.5ºC), temperature control through PID, cooling capacity 600 W at 20ºC, 400W at 0ºC, and 200W at -20ºC. Pump pressure, 1 bar, flow rate > 20 L/min, filling volume > 5 L, with filling level indicator, RS232 port, CE and ISO certified

Air Compressor : Latest design, heavy duty, oil free air compressor must be quoted with the model number and name of manufacturer. Imported chiller and compressor would be preferred

Autoclave : Vertical autoclave of suitable size (with reactor vessel), Microprocessor /Programmable logic controller (PLC) with LCD display for time & temperature with the model number and name of manufacturer

Other accessories Computer & Software : Cylinder and regulator for O2 and CO2 gases, PC of latest configuration with 17” TFT screen and window based data acquisition software for data acquisition.

Personal computer (core i3 4GB RAM and 500GB hard disk) with Laser printer

Annexure - 73

ITEM: Grinder (Mixer)

QUANTITY: 2Nos

Specification:

Mixer Grinder 500 W Power Consumption Wet Grinding Feature Dry Grinding Feature Blending Feature Auto-shut Off for Overload Protection

Annexure - 74

ITEM: Paper Chromatography Cabinet

QUANTITY: 1Nos

Specification:

Paper Chromatography CabinetIt is made of single piece bakelite moulding. The inner size of cabinet is 6x8x9" with front sliding glass door. The lid of cabinet is also made of bakelite.

Stainless Steel Solvent Pot:It is made of 316 Quality S.S. It is having the volume capacity of 150ml. It is required to hold the solvent mixture.

Stainless Steel Hanger:It is a stainless Steel rod of size 6" and dia 2mm. It is used as hanger of Chromatography paper. It fits inside the groves of the cabinet.

Chromatography Paper "1-Chro": It is the world standard Chromatography paper. A smooth surface, 0.18mm thick with linear flow rate (water) of 130mm/30 min. Good resolution for general analytical Separation and having following special features:∗ Simultaneous development of multiple samples on the same sheet under identical conditions. ∗ Sequential development of the same sample with solvent or different concentrations of the same solvent.∗ Suitability for two-dimensional chromatography (change in direction of the solvent front) with possible improved resolution.

Drying Stand:One stand is supplied to accommodate processed (wet) Chromatography paper and to put it in oven to dry the same.

Glass Sprayer with Rubber Balloon:The sprayer is made of Borosilicate Glass, specially designed for spraying the indicators on CHromatography Paper. A rubber balloon is Connected to it.

Glass Syringe:Glass syringe capacity 20 ml. is provided to draw the solvent from S.S. Pot after practical is over.

TLC Capillary:Pkt. of 25 high quality fine capillaries are supplied with cabinet. 

Annexure 75

Item: UV-VIS Spectrophotometer

Nos: 1

Specifications:

PC based high performance, double beam Spectrophotometer with UV-Probe Windows NT based software for operation on 220V / 50Hz.

Photometric System : Double beam optics direct ratio system with Dynode feedback. Wavelength Range : 900nm to 190nm Spectral Bandwidth : 0.1, 0.2, 0.5, 1, 2, & 5nm Wavelength Accuracy : + 0.3nm Wavelength Scanning Speed : Fast, Medium, Slow & Super Slow.

Stray Light : Less than 0.015% at 220nm & 340 nm Photometric Accuracy : + 0.004 Abs. at 1.0 Abs. & + 0.002 Abs. at 0.5 Abs. Photometric Range : -4 Abs. to 5 Abs. 0.0% to 999.9%T 0.0% to 999.9%R Monochomator : Aberration corrected concave blazed holographic grating with

Czerny-Turner mounting. Light Source : 50W Halogen and Deuterium lamp. Standard Software : Spectrum measurement , Photometric, Kinetics. templates, multi-

page print-out support; detailed on-line Help

Data Processing: GLP/GMP Compliance, Unlimited number of custom equations, Pass /

Fail Indications, Unlimited display of spectra, Comparison of spectra, Unlimited display of Kinetic curves, Multiple transformations simultaneously, Quick report templates, What You See Is What You Get report layout and print preview, Multiple page reports

Quartz Cell, 10mm Path length,3.5ml and 1.0ml capacity- 1 Pair Branded PC and Printer – 1 No. each

Annexure: 76

Item: FT-IR Spectrometer

Quantity:1

Specifications:

The FT-IR will be used for the analysis of powder, liquid, Gel & Paste samples

It must have a scan range of 7,000-500 cm-1 with ZnSe beamsplitter only.

Spectral resolution must be 0.8 cm-1 or better.

Wavenumber accuracy of at least ± 0.01 cm-1 or Better

Signal-to-Noise: 50,000:1 or better at resolution 4 cm-1.

The source should be stabilized to prevent hot spots forming.

Interferometer must be rock solid permanently aligned and highly stable.

Optics: All mirrors must be gold coated only.

System should have DLATGS detector.

The instrument should be connected with computer through Ethernet cable and should

indicate whether the source, laser & other parts of instrument are operational.

Critical components must be checked prior to every scan with ability to automatically

recognize accessories are essential.

System must be quoted along with ATR to analyze all type of sample like

Powder, Liquid, Gel & Paste etc. without any sample preparation.

Software – should be Windows based system with facilities like Instrument control,

Basic and advanced data manipulation routines, Spectral calculator, quantification etc.

System must be quoted with high humidity resistant ZnSe beamsplitter only.

All necessary local accessories like Hydraulic Press, Agate Mortar & Pestle, Pellet

Die, Liquid Demountable Cell, IR Grade KBr Powder, Computer & printer must be

quoted along with the equipment.

System must be quoted with 10 years warranty on Interferometer & 5 years

warranty on Laser & Source.

Credibility: Similar installations of this kind should have been made by company in recognized research institute/university in India and provide the user’s list for the same.

Annexure - 77

ITEM: Blot Scanner

QUANTITY: 1

Specifications:

Image Area: 10.0 cm x 8.5 cm Resolution:196 µm x 196 µm

Operating Conditions: For indoor use only; operating temperature 15-30 °C and dew point not greater than 25 °C, non-condensing;

Detector Type: Low-noise CCD.

Acquisition Times: Approximately 6 (Standard) and 12 (High) minutes.

Image Generation and Format: 16 bit floating point tiffs.

Image Display Options: Pseudocolor, positive and negative grayscale, single color (red, green or blue).

Power Requirements: 12VDC, 1A maximum, provided by external power supply. External power supply requires 100-240 VAC (voltage fluctuations not to exceed 10% of the nominal voltage), 1A maximum, 50-60 Hz.

Connections to Computer: Cat. 5E RJ-45 cable (10BASE-T/100BASE-TX) or USB 2.0 Type A to Type B cable. Use only the supplied cables.

Product Dimensions: 27.94 cm L x 22.23 W x 7.3 H(11" L x 8.75" W x 2.875" H)

Weight: 2.18 kg (4.8 lbs.)

Product Includes: Blot Scanner, laptop, mouse, target image, external power supply, Ethernet cable, USB cable, and software and resource CDs.

Accessories: Consumables of an year including conjugated antibodies.

Annexure-78FORMAT FOR MANUFACTURER’S AUTHORISATION LETTER TO AGENT

(On letter head)

Ref. No. Date:

To

The Registrar,

Central University of Rajasthan,

Bandarsindri, Distt. Ajmer,

Rajasthan - 305801

Sub. : Tender for Supply & Installation of Instruments.

Dear Sir,

We, _______________________, who are established and reputed manufacturers of _____________________, having factory at____________________, hereby authorize M/s._________________________________________________________________________________________ (name & address of Indian distributor / agent) to bid, negotiate and conclude the order with you for the above goods manufactured by us.

We shall remain responsible for the tender/ Agreement negotiated by M/s ___________________________, jointly and severely.

An agency commission of _______ % included in the FOB price is payable to M/s _____________________________________________ . We hereby extend our full guarantee and warranty as per the terms and conditions of tender for the goods offered for supply against this invitation for bid by the above supplier.

1. __________________________________________

2. __________________________________________

(specify in detail manufacturer’s responsibilities)

The services to be rendered by M/s. ______________________ _____________ are as under:

1) _________________________________________

2) _________________________________________

(Specify the services to be rendered by the distributor / agent)

In case duties of the Indian agent/distributor are changed or agent/ distributor is changed it shall be obligatory on us to automatically transfer all the duties and obligations to the new Indian Agent failing which we will ipso-facto become liable for all acts of commission or omission on the part of new Indian Agent/ distributor.

Yours faithfully,

[Name & Signature] for and on behalf of M/s. ___________________ [Name of manufacturer]

Annexure– XV

DECLARATION REGARDING BLACKLISTING / DEBARRING FOR TAKING PART IN TENDER.

(To be executed &Attested by Public Notary / Executive Magistrate on Rs.50/- non judicial Stamp paper by the bidder)

I / We ________________________ Manufacture / Partner(s)/ Authorized Distributor /agent of M/S. ___________________________________________ hereby declare that the firm/company namely M/s.__________________________________________________has not been blacklisted or debarred in the past by Union / State Government or organization from taking part in Government tenders in India.

Or

I / We ________________________ Manufacture / Partner(s)/ Authorized Distributor / agent of M/s. ___________________________________________________________hereby declare that the Firm / company namely M/s._________________________________________________________was blacklisted or debarred by Union / State Government or any Organization from taking part in Government tenders for a period of ____________________ years w.e.f. __________ to _____________. The period is over on ________________and now the firm/company is entitled to take part in Government tenders.

In case the above information found false I / we are fully aware that the tender / contract will be rejected / cancelled by Registrar, Central University of Rajasthan, and EMD / SD shall be forfeited.

In addition to the above, Central University of Rajasthan, will not be responsible to pay the bills for any completed / partially completed work.

Name_____________________

Address ___________________

___________________

Attested:

(Public Notary / Executive Magistrate)

Annexure– 79

CERTIFICATE OF GUARANTEE/WARRANTY

I/We certify that the guarantee/warranty shall be for a period of 36/60months (as applicable) starting from the date of satisfactory installation, commissioning and handing over of the equipment and of the works conducted therewith covered under the Supply order in working order. During the guarantee/warranty period, I/we shall provide free “after sale service” and the replacement of any part(s) of the equipment or rectification of defects of work of the equipment will be free of cost. The replacement of the parts shall be arranged by us, at our own cost and responsibility. We undertake that the above guarantee / warranty shall begin

only from the date of satisfactory and faultless functioning of the equipment for 60 days at University premises. The benefit of change in dates of the guarantee / warranty period shall be in the interest of the use/your organization.

During the warranty period, we shall provide at least 4 preventive maintenance visits per year.

Uptime Guarantee: During the guarantee/warranty period, we will be responsible to maintain the equipment in good working conditions for a period 347 days (i.e. 95% uptime) in a block of 365 days.

All complaints will be attended by us within 2 working days of receipt of the complaint in our office.

In case there is delay of more than 2 days in attending to a complaint from our side then you can count the number of days in excess of the permissible response time in the downtime. The above said response time of 2 days for attending to a complaint by us will not be counted in the downtime.

Penalty: We shall pay a penalty equivalent to 0.50% of the FOB value of the equipment for every week or part thereof delay in rectifying the defect.

Note: The right to accept the reason(s) for delay and consider reduction or waive off the penalty for the same shall be at the sole discretion of University.

We certify that the equipment being/quoted is the latest model and that spares for the equipment will be available for a period of at least 10 years and we also guarantee that we will keep the organization informed of any update of the equipment over a period of 10 years.

We guarantee that in case we fail to carry out the maintenance within the stipulated period, University reserves the right to get the maintenance work carried out at our risk, cost and responsibility after informing us. All the expenses including excess payment for repairs/maintenance shall be adjusted against the Performance Bank Guarantee. In case the expenses exceed the amount of Performance Bank Guarantee, the same shall be recoverable from us with/without interest in accordance with the circumstances.

We shall try to repair the equipment at University premises itself. However, the equipment will be taken to our site on our own expenses in case it is not possible to repair the same at University. We shall take the entire responsibility for the safe custody and transportation of the equipment taken out for repairs till the equipment is rehabilitated to the University after repair. Any loss of equipment or its accessories under its charge on account of theft, fire or any other reasons shall be at our sole risk and responsibility which will be compensated to University for such losses.

We undertake to perform calibration after every major repair/breakdown/taking the equipment for repair out of University premises.

In case of extended guarantee/warrantee, we undertake to carry out annual calibration of the equipment.

We guarantee that we will supply spare parts if and when required on agreed basis for an agreed price. The agreed basis could be an agreed discount on the published catalogue price.

We guarantee to the effect that before going out of production of spare parts, we will give adequate advance notice to you so that you may undertake to procure the balance of the life time requirements of spare parts.

We guarantee the entire unit against defects of manufacture, workmanship and poor quality of components.

Signature of Bidder

CENTRAL UNIVERSITY OF RAJASTHAN

TENDER FORM

(Techno Commercial UN priced Bid)

-

Tender No……………….

To

The ______________

____________________

Dear Sir,

1. I/We hereby offer to supply the items as listed in the schedule to this tender hereto/portion thereof as you may specify in the acceptance of Tender at the price given in the said Schedule and agree to hold this offer open for a period of 90 days from the date of opening of the tender. I/we shall be bound by a communication of acceptance issued by you.

2. I/We have understood the Instruction to bidders and Conditions of Contract in the form as enclosed with the invitation to the tender and have thoroughly examined the specifications quoted in the Schedule hereto and am/are fully aware of the nature of the goods required and my/our offer is to supply the goods strictly in accordance with the specifications and requirements.

3. A crossed Bank Draft in favor of the Registrar, Central University of Rajasthan for Rs. ….… (Rupees……………….only) as Earnest Money is enclosed. The Draft is drawn on ……………………………………..Bank payable at Bandarsindri.

4. The following have been added to form part of this tender.

a) Details of items quoted for, as per instructions provided in the schedule of requirement.

b) Schedule of requirements, quoting the make only duly signed and stamped (without indicating price)

c) Sales Tax clearance certificate.

d) Copy of last audited balance sheet.

e) Copy of Valid Central/State sales tax registration certificate.

f) Proof of manufacturing Unit.

g) Statement of deviations from financial terms & conditions, if any.

h) Manufacturer’s Authorization Certificate on their letter pad.

i) Technical Specifications Compliance statement along with original Boucher / literature.

j) Any other enclosure. (Please give details)

5. We undertake to execute all orders which have been placed to meet emergent requirements on priority basis.

6. Certified that the bidder is:

a) A sole proprietorship firm and the person signing the bid document is the sole proprietor/constituted attorney of the sole proprietor,

OR

b) A partnership firm, and the person signing the bid document is a partner of the firm and he has authority to refer to arbitration disputes concerning the business of the

partnership by virtue of the partnership agreement/by virtue of general power of attorney.

OR

c) A company and the person signing the document is the constituted attorney.

(NOTE: Delete whatever is not applicable. All corrections/deletions should invariable be duly attested by the person authorized to sign the bid document).

7. We do hereby undertake that, until a formal notification of award, this bid, together with your written acceptance thereof shall constitute a binding contract between us.

Yours faithfully,

(Signature of bidder)

Dated this day of ______________________

Address…

……………………………..

……………………………..

Telephone:_____________

FAX__________________

E-mail_________________

Company seal

Central University of Rajasthan

Tender Form(Priced Bid)

To

The _________________ _________________ _________________

Ref: Tender No ……………………………….. Dated---------

Sir,Having examined the bidding documents and having submitted the techno commercial unpriced bid for the same, we, the undersigned, hereby submit the priced bid for supply of goods and services as per the schedule of requirements and in conformity with the said bidding documents.We hereby offer to supply the Goods/Services at the prices and rates mentioned in the enclosed schedule of requirement.

We do hereby undertake that, in the event of acceptance of our bid, the supply of Goods/Services shall be made as stipulated in the schedule of requirement and that we shall perform all the incidental services.

The prices quoted are inclusive of all charges net F.O.R University. We enclose herewith the complete Financial Bid as required by you. This includes:

i. Price Schedule as per schedule of requirement.ii. Statement of deviations from financial terms and conditions.

We agree to abide by our offer for a period of 180 days from the date fixed for opening of the bid documents and that we shall remain bound by a communication of acceptance within that time.

We have carefully read and understood the terms and conditions of the bid document and we do hereby undertake to supply as per these terms and conditions. The Financial Deviations are only those mentioned in the statement of deviations from financial terms and conditions.

Certified that the bidder is:A sole proprietorship firm and the person signing the bid document is the sole proprietor/ constituted attorney of sole proprietor,

OrA partnership firm, and the person signing the bid document is a partner of the firm and he has authority to refer to arbitration disputes concerning the business of the partnership by virtue of the partnership agreement/by virtue of general power of attorney,

OrA company and the person signing the bid document is the constituted attorney.

(NOTE: Delete whatever is not applicable. All corrections/deletions should invariably be duly attested by the person authorized to sign the bid document.)We do hereby undertake that, until a formal notification of award, this bid, together with your written acceptance thereof, shall constitute a binding contract between us.

Dated this day of_________ Signature of BidderDetails of enclosures Full Address:

Fax No.E-mail:COMPANY SEAL

Price Schedule “A”

E.M.D.______________________

D.D. Details_________________

Bank Name_________________

Date__________________________

Item No.

Item Name Basic Price

Taxes and duties(if any) with rate & details

Delivery chargesOther charges (if any)

Total Price F.O.R.at Central University of Rajasthan.All inclusive

1

2

3

4

5

6

7

8

9

10

11

12

13

Total No. of Item(s) quoted_______ Seal and Signature of the bidder

S. No. Item Name AMC(4th Year)

AMC(5th Year)

Seal and Signature of the bidder

Checklist for Bid/Tender Submission

The following check-list must be filled in and submitted with the bid document:

Pre-qualification Bid

1. Was the bid document issued to you? Yes/No

2. Have you attached the techno commercial unpriced bid form duly filled in appropriately

Yes/No3. Have you attached a copy of the last audited balance sheet of your firm?

Yes/No4. Have you attached the details of the income tax clearance certificate,proof of

manufacturing unit/ dealership letter/general order suppliersand copy of Central/State sales tax registration certificate?Yes/No

5. Have you attached the copies of relevant work orders (without any alteration) from Govt. Deptt/PSUs and Central Autonomous Bodies?Yes/NoEMD: Have you submitted EMD asked for?Yes/No

6. Have you submitted samples of all items indicated in the respectiveSchedule of requirements? Yes/No

7. Have you enclosed the schedule of requirement indicating the makeoffered without indicating the pricing components along with the technocommercial unpriced bid?Yes/No

8. Have you submitted the bids both techno commercial unpriced and pricedbid separately for each tender? Yes/No

9. Have you enclosed the statement of deviations from financial terms andconditions, if any? Yes/No

Priced Bid:

1. Have you signed and attached the priced bid form. Yes/No

2. Have you attached the schedule of requirements duly priced Yes/No

PERFORMANCE BANK GUARANTEE

WHEREAS M/s …………….…………………………., having its registered office at ………………………………………………… hereinafter called the Distributor in India for……………………………………………………………………………………………..………, herein after called “The supplier” for the supply of …………., in consideration of the Central University of Rajasthan, Department of ………………….., School of …………………Central University of Rajasthan, , Kishangarh (hereinafter called “CURAJ”) P.O. No. CURAJ / …………………. dt. placed an order for the due fulfillment by the said supplier of the terms and conditions in the purchase order, on production of a Bank Guarantee for Rs………….. (Rupees…………………………….. only). We ……….. Bank, ……………… (Rein after referred to as “the Bank”) at the request of supplier do hereby undertake to pay to the CURAJ an amount on exceeding to Rs………… (Rupees……………………….. only).

2. We …………Bank do hereby undertake to pay CURAJ, the amounts due and payable under this guarantee without any demur, merely on a demand from CURAJ stating that the amount claimed is required to meet the recoveries due or likely to be due from the said supplier. Any such demand made on the Bank shall be conclusive as regards the amount due and payable by the Bank under the guarantee. However, our liability under this guarantee shall be restricted to an amount not exceeding to Rs……….(Rupees …………………………….. only)

3. We undertake to pay to the CURAJ any money so demanded notwithstanding any dispute or disputes raised by the supplier in any suit or proceeding pending before any court or Tribunal relating thereto, our liability under this present being absolute and unequivocal. The payment so made by us under this bond shall be valid and discharge of our liability for payment there under and the Supplier shall have no claim against us for making such payment.

4. We the …………Bank further agree that the guarantee herein contained shall remain in full force and affect during the period that would be taken for the performance of the said Agreement and that it shall continue to be enforceable till all the dues of the CURAJ under or by virtue of the said Agreement have been fully paid and its claims satisfied or discharged or till Registrar on behalf of the CURAJ certified that the terms and conditions of the said Agreement have been fully and properly carried out by the said ……………… and accordingly discharges this guarantee.

5. We, the ………….. Bank further agreed that the CURAJ shall have the fullest liberty without our consent and without affecting in any manner our obligations here under to vary any of the terms and conditions of the said Purchase Order or to extend the time of performance by the said contractor from time to time or to postpone for any time or from time to time any of the powers exercisable by the CURAJ against the said supplier and to forbear or enforce any of the Terms and Conditions relating to the said agreement and we shall not be relieved from our liability by reason of any such variation or extension being granted to the said supplier or for any forbearance act or omission on the part of the CURAJ or any indulgence by the CURAJ to the said supplier or by any such matter or thing whatsoever which under the law relating to sureties would but for this provision have effect of so relieving us.

6. This guarantee will not be discharged due to change in the constitution of the bank or the supplier.

7. We, the ………….. Bank lastly undertakes not to revoke this guarantee except with the previous consent of the CURAJ in writing.

8. This guarantee shall be valid upto …………………… unless extended on demand by CURAJ. Notwithstanding anything mentioned above, our liability against this guarantee is restricted to Rs………/- (Rupees ……………………………. only).

Notwithstanding anything contained herein1. Our liability under this bank guarantee shall not exceed Rs………../- (Rupees……………………………….. only)

2. Bank guarantee shall be valid upto …………………..

3. We are liable to pay the guaranteed amount or part thereof under this bank guarantee only and only if you serve upon us a written claim or demand on or before ……………………..

Dated:Signature & Seal of the Bank

Note: The aboveformatcontainsspecificclausesandexpressions.Theseclausesand expressions can vary depending upon the nature / type of agreement and situation. Basic aspect to be kept in mind is that interest of CURAJ is fully protected.