Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)

This document describes the features, bugs, and limitations for Cisco Nexus 3000 Series and Cisco Nexus 3100 Series switches. Use this document in combination with documents listed in the Obtaining Documentation and Submitting a Service Request section.

Note: Starting with Cisco NX-OS Release 7.0(3)I2(1), the Cisco NX-OS image filename has changed to start with "nxos" instead of "n3000."

Table 1 shows the online change history for this document.

Table 1 Online History ChangeDate Description

May 16, 2016 Created NX-OS Release 7.0(3)I4(1) release notes.

November 22, 2017 Added a note to specify the requirements while upgrading from Cisco NX-OS Release 6.0(2)U6(2) (CSCvb78728).

March 9, 2018 Added a limitation for IGMP snooping.

Contents

Introduction.....................................................................................................................................................................2

System Requirements......................................................................................................................................................3

New and Changed Information........................................................................................................................................6

Caveats.............................................................................................................................................................................8

Upgrade and Downgrade Guidelines.............................................................................................................................12

Upgrade Matrix..............................................................................................................................................................13

Limitations.....................................................................................................................................................................14

MIB Support...................................................................................................................................................................16

Related Documentation.................................................................................................................................................17

Documentation Feedback..............................................................................................................................................17

Obtaining Documentation and Submitting a Service Request........................................................................................17

Cisco Systems, Inc.      www.cisco.com

1

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

IntroductionSeveral new hardware and software features are introduced for the Cisco Nexus 3000 Series and Cisco Nexus 3100 Series devices to improve the performance, scalability, and management of the product line. Cisco NX-OS Release 7.x also supports all hardware and software supported in Cisco NX-OS Release 6.x, Cisco NX-OS Release 5.1, and Cisco NX-OS Release 5.0.

Cisco NX-OS offers the following benefits:

■ Cisco NX-OS runs on all Cisco data center switch platforms: Cisco Nexus 7000, Nexus 5000, Nexus 4000, Nexus 3000, Nexus 2000, and Nexus 1000V Series switches.

■ Cisco NX-OS software interoperates with Cisco products that run any variant of Cisco IOS software and also with any networking operating system that conforms to common networking standards.

■ Cisco NX-OS modular processes are triggered on demand, each in a separate protected memory space. Processes are started and system resources are allocated only when a feature is enabled. The modular processes are governed by a real-time preemptive scheduler that helps ensure timely processing of critical functions.

■ Cisco NX-OS provides a programmatic XML interface that is based on the NETCONF industry standard. The Cisco NX-OS XML interface provides a consistent API for devices. Cisco NX-OS also provides support for Simple Network Management Protocol (SNMP) Versions 1, 2, and 3 MIBs.

■ Cisco NX-OS enables administrators to limit access to switch operations by assigning roles to users. Administrators can customize access and restrict it to the users who require it.

This section includes the following:

■ Cisco Nexus 3000 Series Switches

■ Cisco Nexus 3100 Series Switches

Cisco Nexus 3000 Series SwitchesThe Cisco Nexus 3000 Series switches are high-performance, high-density, ultra-low-latency Ethernet switches that provide line-rate Layer 2 and Layer 3 switching. The Cisco Nexus 3000 Series includes the following switches:

■ The Cisco Nexus 3064 switch is a 1 RU switch that supports 48 1- or 10-Gigabit downlink ports, four Quad Small Form-Factor Pluggable (QSFP+) ports that can be used as a 40 Gigabit Ethernet port or 4 x10-Gigabit Ethernet ports, one 10/100/1000 management port, and one console port.

■ The Cisco Nexus 3048 switch is a 1 rack unit (RU) switch that supports 48 10/100/1000 Ethernet server-facing (downlink) ports, four 10-Gigabit network-facing (uplink) ports, one 100/1000 management port, and one console port.

■ The Cisco Nexus 3016 is a 1 RU, 16-port QSFP+ switch. Each QSFP+ port can be used as a 40-Gigabit Ethernet port or 4 x10-Gigabit Ethernet ports.

Each switch includes one or two power supply units and one fan tray module, and each switch can be ordered with either forward (port-side exhaust) airflow or reverse (port-side intake) airflow for cooling. All platforms support both AC and DC power supplies. All combinations of power (AC/DC) and airflow (forward/reverse) are available. The Cisco Nexus 3000 Series switches run the Cisco NX-OS software.

For information about the Cisco Nexus 3000 Series, see the Cisco Nexus 3000 Series Hardware Installation Guide.

2

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

Cisco Nexus 3100 Series SwitchesThe Cisco Nexus 3100 Series switches are high-performance, high-density, ultra-low-latency Ethernet switches that provide line-rate Layer 2 and Layer 3 switching. In Cisco NX-OS Release 6.0(2)U2(2), the Cisco Nexus 3100 Series includes the Cisco Nexus 3132 and Nexus 3172 switches.

The Cisco Nexus 3172PQ switch is a 10-Gbps Enhanced Small Form-Factor Pluggable (SFP+)–based ToR switch with 48 SFP+ ports and 6 Enhanced Quad SFP+ (QSFP+) ports.

The Cisco Nexus 3172TQ switch is a 10GBASE-T switch with 48 10GBASE-T ports and 6 Quad SFP+ (QSFP+) ports.

Each SFP+ port can operate in 100-Mbps, 1-Gbps, or 10-Gbps mode, and each QSFP+ port can operate in native 40-Gbps or 4 x 10-Gbps mode. This switch is a true physical-layer-free (phy-less) switch that is optimized for low latency and low power consumption.

The Cisco Nexus 3132Q switch is a 1RU, 40-Gbps QSFP-based switch that supports 32 fixed 40-Gbps QSFP+ ports. It also has 4 SFP+ ports that can be internally multiplexed with the first QSFP port. Each QSFP+ port can operate in the default 40-Gbps mode or 4 x 10-Gbps mode, up to a maximum of 104 10-Gbps ports.

Each switch includes dual redundant power supply units, four redundant fans, one 10/100/1000 management port, and one console port. Each switch can be ordered with either forward (port-side exhaust) airflow or reverse (port-side intake) airflow for cooling. It supports both AC and DC power supplies. All combinations of power (AC/DC) and airflow (forward/reverse) are available. The Cisco Nexus 3100 Series switches run the Cisco NX-OS software.

For information about the Cisco Nexus 3100 Series, see the Cisco Nexus 3000 Series Hardware Installation Guide.

System RequirementsThis section includes the following topics:

■ Memory Requirements

■ Hardware Supported

■ Twinax Cable Support on Cisco Nexus 3000 Switches

■ Cisco QSFP 40-Gbps Bidirectional Short-Reach Transceiver

Memory RequirementsThe Cisco NX-OS Release 7.0(3)I4(1) software requires 135 MB of flash memory.

Hardware SupportedCisco NX-OS Release 7.0(3)I4(1) supports the Cisco Nexus 3000 Series switches. You can find detailed information about supported hardware in the Cisco Nexus 3000 Series Hardware Installation Guide. See Table 2 for the hardware supported by the Cisco NX-OS Release 7.x software.

3

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

Table 2 Hardware Supported by Cisco NX-OS Related 7.x Software. Hardware Part Number

Cisco Nexus 3132Q-X switch N3K-C3132Q-40GX

Cisco Nexus C3172TQ-XL switch N3K-C3172TQ-XL

Cisco Nexus C3172PQ-XL switch N3K-C3172PQ-XL

Cisco Nexus C3132Q-XL switch N3K-C3132Q-XL

Cisco Nexus 3172TQ switch N3K-C3172TQ-10GT

Cisco Nexus 3172PQ switch N3K-C3172PQ-10GE

Cisco Nexus 3132Q-V switch N3k-C3132Q-V

Cisco Nexus 3132Q switch N3K-C3132Q-40GE

Cisco Nexus 31108TC-V N3K-C31108TC-V

Cisco Nexus 31108PC-V switch N3K-C31108PC-V

Cisco Nexus 3064-X switch N3K-C3064PQ-10GX

Cisco Nexus 3064-X reversed airflow (port-side intake) AC power supply

N3K-C3064-X-BA-L3

Cisco Nexus 3064-X forward airflow (port-side intake) DC power supply

N3K-C3064-X-BD-L3

Cisco Nexus 3064-X forward airflow (port-side exhaust) DC power supply

N3K-C3064-X-FD-L3

Cisco Nexus 3064-X forward airflow (port-side exhaust) AC power supply

N3K-C3064-X-FA-L3

Cisco Nexus 3064-TQ switch N3K-C3064TQ-10GT

Cisco Nexus 3064-T 500W reverse airflow (port-side intake) AC power supply

NXA-PAC-500W-B

Cisco Nexus 3064-T 500W forward airflow (port-side ex-haust) AC power supply

NXA-PAC-500W

Cisco Nexus 3064-E switch N3K-C3064PQ-10GE

Cisco Nexus 3064 switch N3K-C3064PQ

Cisco Nexus 3064 fan module with reverse airflow (port-side intake); also used in the Cisco Nexus 3016

N3K-C3064-FAN-B

4

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

Hardware Part Number

Cisco Nexus 3064 fan module with forward airflow (port-side exhaust); also used in the Cisco Nexus 3016

N3K-C3064-FAN

Cisco Nexus 3048 switch N3K-C3048TP-1GE

Cisco Nexus 3048 fan module with reverse airflow (port-side intake)

N3K-C3048-FAN-B

Cisco Nexus 3048 fan module with forward airflow (port-side exhaust)

N3K-C3048-FAN

Cisco Nexus 3016 switch N3K-C3016Q-40GE

Cisco Nexus 3000 power supply with reverse airflow (port-side intake)

N2200-PAC-400W-B

Cisco Nexus 3000 power supply with forward airflow (port-side exhaust)

N2200-PAC-400W

Cisco Nexus 2000 power supply with forward airflow (port-side exhaust)

N2200-PDC-400W

Cisco Nexus 2000 DC power supply with reverse airflow (port-side intake)

N3K-PDC-350W-B

Twinax Cable Support on Cisco Nexus 3000 SwitchesStarting with Cisco Release NX-OS 5.0(3)U1(1), the following algorithm is used to detect copper SFP+ twinax, QSFP+ twinax, and QSFP+ splitter cables on Cisco Nexus 3000 Series switches.

If the attached interconnect (transceiver) is a copper SFP+ twinax or QSFP+ twinax cable:

■ Verify the transceiver SPROM to match the Cisco magic code.

■ If the check succeeds, bring up the interface. Otherwise, print the following warning message appears stating that a non-Cisco transceiver is attached and that you should try to bring up the port.

2009 Oct 9 01:46:42 switch %ETHPORT-3-IF_NON-CISCO_TRANSCEIVER: Non-Cisco transceiver on interface Ethernet1/18 is detected.

If the attached transceiver is a QSFP+ splitter cable, then no special check is performed. The Cisco NX-OS software tries to bring up the port.

The following disclaimer applies to non-Cisco manufactured and non-Cisco certified QSFP copper splitter cables:

If a customer has a valid support contract for Cisco Nexus switches, Cisco TAC will support twinax cables that are a part of the compatibility matrix for the respective switches. However, if the twinax cables are not purchased through Cisco, a customer cannot return these cables through an RMA to Cisco for replacement.

If a twinax cable that is not part of the compatibility matrix is connected into a system, Cisco TAC will still debug the problem, provided the customer has a valid support contract on the switches. However

5

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

TAC may ask the customer to replace the cables with Cisco qualified cables if there is a situation that points to the cables possibly being faulty or direct the customer to the cable provider for support. Cisco TAC cannot issue an RMA against uncertified cables for replacement.

Cisco QSFP 40-Gbps Bidirectional Short-Reach TransceiverThe Cisco QSFP 40-Gbps Bidirectional (BiDi) transceiver is a short-reach pluggable optical transceiver with a duplex LC connector for 40-GbE short-reach data communications and interconnect applications by using multimode fiber (MMF). The Cisco QSFP 40-Gbps BiDi transceiver offers a solution that uses existing duplex MMF infrastructure for 40-GbE connectivity. With the Cisco QSFP 40-Gbps BiDi transceiver, customers can upgrade their network from 10-GbE to 40-GbE without incurring any fiber infrastructure upgrade cost. The Cisco QSFP 40-Gbps BiDi transceiver can enable 40-GbE connectivity in a range of up to 100 meters over OM3 fiber, which meets most data center reach requirements. It complies with the Multiple Source Agreement (MSA) QSFP specification and enables customers to use it on all Cisco QSFP 40-Gbps platforms and achieve high density in a 40-GbE network. It can be used in data centers, high-performance computing (HPC) networks, enterprise and distribution layers, and service provider transport applications.

New and Changed InformationThis section lists the new and changed information in Release 7.0(3)I4(1):

■ New Supported Hardware

■ New Software Features

New Supported HardwareCisco NX-OS Release 7.0(3)I4(1) supports the following hardware:

■ Cisco Nexus 31108PC-V (N3K-C31108PC-V) – 1 rack unit (RU) top of rack (TOR) L3 switch, which comes with 48 10G SFP+ and 6 QSFP28 ports, 1 management port (RJ-45 or SFP), 1 console port, and 1 USB port. This switch features support for 100G uplinks.

■ Cisco Nexus 31108TC-V (N3K-C31108TC-V) – 1 rack unit (RU) top of rack (TOR) L2/L3 switch, which comes with 48 10G Base-T and 6 QSFP28 ports, 1 management port (RJ-45 or SFP), 1 console port, and 1 USB port. This switch features support for 100G uplinks.

■ Cisco Nexus 3132Q-V (N3k-C3132Q-V) – 1 rack unit (RU) switch with 32 40-Gigabit enhanced quad small form-factor pluggable (QSFP+) ports and 4 SFP+ ports that are internally multiplexed with the first QSFP+ port. Each QSFP+ port can operate in native 40-Gigabit or 4 x 10-Gigabit modes. This switch features support for the following:

¯ VxLAN routing

¯ 33% more packet buffer

¯ 2x system memory for object-model programming

¯ 4x ingress ACL (Access Control List)

New Software FeaturesCisco NX-OS Release 7.0(3)I4(1) includes the following new software features:

Fundamentals Features

6

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

■ POAP dynamic breakout – Dynamically breaks out ports in an effort to detect a DHCP (Dynamic Host Channel Protocol) server behind one of the broken-out ports. Previously, the DHCP server used for POAP (Power On Auto Provisioning) had to be directly connected to a normal cable because breakout cables were not supported.

■ POAP personality – Enables user data, Cisco NX-OS and third-party patches, and configuration files to be backed up and restored. In previous releases, POAP can restore only the configuration.

■ Variable support – Enables Cisco NX-OS CLI variables to contain hyphens and underscores.

For more information, see the Cisco Nexus 3000 Series NX-OS Fundamentals Configuration Guide.

Interfaces and VXLAN Features

■ Configuring port profiles – Added support for port profiles.

■ Configuring VXLAN BGP EVPN – Added support for configuring VXLAN BGP EVPN.

■ Support for changing VRF membership for an SVI – Added support for changing VRF membership for an SVI.

■ Support for Flood & Learning and L3EVPN (Layer 3 Ethernet VPN) has been added on the following switches:

¯ Cisco Nexus 3132Q-V

¯ Cisco Nexus 31108PC-V

¯ Cisco Nexus 31108TC-V platforms

■ Support for L2EVPN (Layer 2 Ethernet VPN) has been added on the following switches:

¯ Cisco Nexus 3132Q-V

¯ Cisco Nexus 31108PC-V

¯ Cisco Nexus 31108TC-V

¯ Cisco Nexus 3132Q

¯ Cisco Nexus 3172 platforms

■ suppress mac-route command –Support for suppress mac-route command. Suppresses the BGP (Border Gateway Protocol) MAC route so that BGP only sends the MAC/IP route for a host.

For more information, see the Cisco Nexus 3000 Series NX-OS Interfaces Configuration Guide.

Label Switching Feature

■ Segment Routing – Added support for Segment Routing.

For more information, see the Cisco Nexus 3000 Series NX-OS Label Switching Configuration Guide.

Multicast Routing Features

■ PIM SSM over vPCs – Enables support for IGMPv3 joins and PIM S,G joins over vPC (Virtual Port Channel) peers in the SSM range. This configuration is supported for orphan sources or receivers in the Layer 2 or Layer 3 domain.

7

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

For more information, see the Cisco Nexus 3000 Series NX-OS Multicast Routing Configuration Guide.

Security Features

■ AAA enhancement – Adds the ability to log successful and failed login attempts.

■ ACL detailed logging cache – Enables ACE (access control entry) and ACL information to be displayed in the output of the show logging ip access-list cache command.

■ CoPP enhancement – Changed the police CIR rate range to start with 0 to initiate a packet drop.

For more information, see the Cisco Nexus 3000 Series NX-OS Security Configuration Guide.

Software Upgrade and Downgrade Features

■ In-service software upgrade (ISSU) enhancements – Adds ISSU support for FEX, NAT, segment routing, and VXLAN. An ISSU from Cisco NX-OS Release 7.0(3)I4(1) to a later release is non-disruptive for these features.

For more information, see the Cisco Nexus 3000 Series NX-OS Software Upgrade and Downgrade Guide.

System Management Features

■ ERSPAN and SPAN – Added support for the same source in multiple sessions and for multiple ACL filters on the same source.  

For more information, see the Cisco Nexus 3000 Series NX-OS System Management Guide.

Unicast Routing Features

■ IS-IS – Added support for IS-IS (Integrated Intermediate System-to-Intermediate System).

■ RPM match for OSPF area ID – Adds the match ospf-area command to match the OSPFv2 or OSPFv3 area ID for route maps.

For more information, see the Cisco Nexus 3000 Series NX-OS Unicast Routing Configuration Guide.

CaveatsThe open and resolved bugs and the known behaviors for this release are accessible through the Cisco Bug Search Tool. This web-based tool provides you with access to the Cisco bug tracking system, which maintains information about bugs and vulnerabilities in this product and other Cisco hardware and software products.

Note: You must have a Cisco.com account to log in and access the Cisco Bug Search Tool. if you do not have one, you can register for an account.

For more information about the Cisco Bug Search Tool, see the Bug Search Tool Help & FAQ.

■ Resolved Bugs for this Release

■ Open Bugs for this Release

■ Known Behaviors for this Release

Resolved Bugs for this ReleaseTable 3 lists descriptions of resovled bugs in Cisco NX-OS Release 7.0(3)I4(1). You can use the record ID to search the Cisco Bug Search Tool for details about the bug.

8

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

Table 3 Cisco NX-OS Release 7.0(3)I4(1) —Resolved BugsRecord Number

Description

CSCuu35333 The system should not be shut down when there is power supply or fan direction mismatch.

CSCuw10613 NX-OS may crash due to the neutron_usd process.

CSCux85404 This is an enhancement request to support different ACL filters on different ERSPAN sessions that contain the same set of source interfaces.

CSCuy32907 Prunes are not being sent for S,G routes, which causes S,G routes to have multiple OIFs for S,G routes to both vPC peers. This causes duplicate multicast traffic to be received.

CSCuy55754 On Cisco Nexus 3000 Series switches running 7.0(3)I2(2b), multicast gets flooded to all ports on a VLAN.

CSCuy61171 The show routing hash command may result in an error message on T2/T+ Cisco Nexus 3000 platforms when the in-interface option is provided.

CSCuy81153 Cisco Nexus 3000 Series switches do not correctly strip provider dot1q tags in QinQ.

CSCuy83502 The BGP route is not advertised to neighbors if the route is filtered by a table-map filter.

CSCuy94496 On 7.0 code, speed 1000 cannot be configured on a breakout interface with a QSA and a 1000base-SX SFP installed.

CSCuz25317 The speed 10 configuration is not available on RJ45 ports of the Cisco Nexus 3048 switch.

CSCuz26217 Enable the DOM alarms for 7.0(3)I4(1).

9

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

Open Bugs for this ReleaseTable 4 lists descriptions of open bugs in Cisco NX-OS Release 7.0(3)I4(1). You can use the record ID to search the Cisco Bug Search Tool for details about the bug.

Table 4 Cisco NX-OS Release 7.0(3)I4(1) —Open BugsRecord Number

Description

CSCuq01107 Static MAC addresses pointing to a vPC PO are flushed and traffic flooding is seen when the vPC PO is made shut.

CSCur14762 After running no shut on the vPC peer-link, some packet duplication occurs for all the sourced multicast groups.

CSCur76020 VRRPv3 tracking support to be added.

CSCuw97656 When ALPM is enabled on vPC devices, inconsistency is detected between the hardware and software MAC table on both vPC nodes after learning more than 32K MAC addresses. In ALPM mode, the supported MAC table limit is 32K. MAC tables on both vPC devices go out of sync.

Known Behaviors for this ReleaseTable 5 lists descriptions of known behaviors in Cisco NX-OS Release 7.0(3)I4(1). You can use the record ID to search the Cisco Bug Search Tool for details about the bug

Table 5 Cisco NX-OS Release 7.0(3)I4(1) —Known Behaviors Record Number

Description

CSCuw38487 python/yum crashes when /tmp is full.

CSCuw56991 When a unicast ARP request packet for Virtual IP gets hashed to HSRP secondary, HSRP secondary should send the packet to active. However, in addition to this, the packet is also being flooded in the VLAN.

CSCuw63806 A BGP session flap is seen after a reboot/fast-reload on QI/Nep platforms.

CSCuw75771 In a vPC scenario where one peer is upgraded to 7.0(3)I2 and another peer is still running 6.0(2)U6:

If on one peer, a vPC peer link is configured to be part of an SVI interface but the other end is not configured to be part of the SVI, a type 2 inconsistency is reported in peer running 7.0(3)I2. The same is not reported in the peer running 6.0(2)U6 as this consistency check is specific to 7.0(3)I2 release only.

This has no functional impact and would be seen only in above mentioned transient scenario.

CSCuw86732 HSRP standby device tunnels the packet to vPC peer.

CSCuw92666 After invoking the clear fabric database host command, the profile remains applied on the secondary vPC switch.

CSCuw97319 clear ip igmp snooping groups * vlan x does not clear IGMP groups learned on a vPC peer.

10

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

Record Number

Description

CSCux01653 The show interface transceiver command output for 40 G copper passive cables changed in release 7.0(3)I2(2). Earlier releases included an additional "(passive)” field.

CSCux02214 The L2 consistency check fails to detect inconsistency between hardware and software L2 entries for an HSRP virtual MAC.

CSCux08559 The show routing hash does not show the exact path for Routes over tunnel.

CSCux10586 OFA: of_agent memory leak during install scale flows.

CSCux10898 OFA: openflow configure gone after reload.

CSCux15298 Alibaba: loopack interface not down after nve shut.

CSCux20954 VRF static route should move to the bottom in show running.

CSCux22283 Bootup time of the box is high.

CSCux23914 For L3 interfaces, for RFC 5549 traffic (advertising v4 routes over v6 interface/neighbors), even if the egress interface is not v4-aware, the traffic will still be forwarded and not dropped.

CSCux24415 PTP Corrections values are higher than expected.

CSCux28141 Counter is not showing CRC error packets in egress direction.

CSCux33633 VPC: Auto-pulled hosts are out of sync among peers.

CSCux35347 ISSU is blocked for upgrade.

CSCux37273 L3 orphan ports on a vPC setup may get duplicate traffic, which is avoidable with some changes in config.

CSCux38031 After configuring Dynamic Arp Inspection, the switch drops the invalid ARP request packets with target protocol address 0.0.0.0 as expected. But statistics for these drop packets are not shown in the show ip arp inspection statistics vlan CLI. These are reflected in the show ip arp statistics CLI.

CSCux38601 Block non-disruptive ISSU if SDK firmware changed.

CSCux39947 TFTP image download fails as ARP to gateway fails in loader prompt.

CSCux46895 Service impacting upgrade/downgrade as it is a ToR switch.

CSCux56810 Management IP address is not reachable from the kickstart boot prompt (also known as recovery prompt).

CSCux58869 Nep-CR: interface port LED's are flapped during an ISSU.

CSCux64729 Tx span is unsupported while configuring vlan interface as source.

CSCux70434 Automatic ARP resolution does not happen for IR peers in VPC setup in specific scenarios.

CSCux76023 N3K_IMR4: XCVR Wavesplitter type is shown as "unknown" type.

CSCux79934 When configuring large access-list on a switch port (> 1533 entries with the default TCAM carving of 1536 entries for the region), the error message:"ERROR: Sufficient free entries are not available in TCAM bank" is seen.

11

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

Record Number

Description

CSCux80557 Feature bash-shell will get enabled on executing show tech install.

Error will be seen on executing show tech install with network operator role.

CSCuv86255 show run bgp all does not reliably nvgen allowas-in [occurrences].

CSCux87794 copy r s is getting stuck at 97% on QI2CR-XL 16GB switch.

CSCuy02203 When the setup script is executed after the system is up and interfaces are configured with non-default configs, the default interface layer and default switchport interface state set in the setup script will not affect those interfaces with non-default configuration.

CSCuy06098 N3K: Hide Shrinkimage option from ISSU command if it is not supported.

CSCuy09656 LED Status shown as incorrectly on QS.

CSCuy11513 User is able change the configuration on the vPC peer when the peer is going through ISSU in conditions where the user already in the config mode.

CSCuy85644 VXLAN access and network ports have been added to the broadcast (BCAST) and multicast (MCAST) domains; this causes packets to flood on all VXLAN ports attached to the MCAST and BCAST domains, including the source port. However, packets are dropped on the egress of the source port. As a result, unknown unicast and broadcast traffic is incremented in the Out-Discard counter without affecting the Xmit-Err counter.

Large core files are split into 3 or more files. For example:

■ 1405964207_0x101_fwm_log.3679.tar.gzaa

■ 1405964207_0x101_fwm_log.3679.tar.gzab

■ 1405964207_0x101_fwm_log.3679.tar.gzac

To decode the multiple core files, first club the files to a single file:

$ cat 1405964207_0x101_fwm_log.3679.tar.gz* > 1405964207_0x101_fwm_log.3679.tar.gz

Upgrade and Downgrade Guidelines■ The only supported method of upgrading is install all from Release 6.0(2)U6(3) due to the need to

upgrade the BIOS. Without the Release 7.0(3)I4(1) BIOS, the 7.0(3)I4(1) image will not load.

■ The no-save option is now required to downgrade from Release 7.x to Release 6.x. The bios-force is a hidden option that is only available on Cisco Nexus 3000 Series switches that are running 7.x releases.

■ Cisco Nexus 3000 Series switches that use software versions older than Cisco NX-OS Release 5.0(3)U5(1) need to be updated to Cisco NX-OS Release 5.0(3)U5(1) before they are upgraded to Cisco NX-OS Release 6.0(2).

■ Cisco NX-OS Release 5.0(3)U3(1) does not support a software upgrade from Cisco NX-OS Release 5.0(3)U2(2c). If you want to upgrade through this path, see CSCty75328 for details about how to work around this issue.

Note: It is recommended that you upgrade to Cisco NX-OS Release 7.0(3)I4(1) by using Cisco NX-OS install procedures.

12

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

■ In Cisco NX-OS Release 6.0(2)U2(2), the default interface name in LLDP MIB is in short form. To make it long form, you must set lldp portid-subtype to 1. In Cisco NX-OS Release 6.0(2)U2(3), this behavior was reversed. The default interface name in LLDP MIB is now in long form. To make it short form, you must set lldp portid-subtype to 0.

■ If you have set lldp port-subtype to 1 and you are upgrading to Cisco NX-OS Release 6.0(2)U2(4), ensure that you set lldp port-subtype to 0.

■ While performing a non-disruptive ISSU, VRRP and VRRPV3 will display the following messages:

¯ If VRRPV3 is enabled:

2015 Dec 29 20:41:44 MDP-N9K-6 %$ VDC-1 %$ %USER-0-SYSTEM_MSG: ISSU ERROR: Service "vrrpv3" has sent the following message: Feature vrrpv3 is configured. User can change vrrpv3 timers to 120 seconds or fine tune these timers based on upgrade time on all Vrrp Peers to avoid Vrrp State transitions. - sysmgr

¯ If VRRP is enabled:

2015 Dec 29 20:45:10 MDP-N9K-6 %$ VDC-1 %$ %USER-0-SYSTEM_MSG: ISSU ERROR: Service "vrrp-eng" has sent the following message: Feature vrrp is configured. User can change vrrp timers to 120 seconds or fine tune these timers based on upgrade time on all Vrrp Peers to avoid Vrrp State transitions. – sysmgr

■ Packet loss can occur on Cisco Nexus 31108PC-V, 31108TC-V and 3132Q-V switches when they are in the default cut-through switching-mode and the default oversubscribed port mode. These packet losses are seen in hardware counters on the egress port as TERR and/or TFCS. One of the following workarounds can be implemented to address this issue without NX-OS upgrade. To view more details, see CSCvf87120.

1. Change the port mode from oversubscribed to line-rate and then reload the switch:

- on Nexus 31108PC-V and 31108TC-V switches, change from 48x10g+6x100g to 48x10g+4x100g+2x40g.

- on Nexus 3132Q-V switches change from 32x40g or 26x40g to 24x40g.

2. Change the switching-mode from cut-through to store-and-forward and then reload the switch.

Upgrade MatrixThis section provides information on upgrading Cisco Nexus 3000 and 3100 Series switches to Cisco NX-OS Release 7.0(3)I4(1).

Note: Beginning with the 7.0(3)I2(1) release, kickstart and system images are no longer used to install the Cisco NX-OS software image on Cisco Nexus 3000 and 3100 Series switches. Instead, a single binary image is used (for example, nxos.7.0.3.I4.1.bin). To install the software, you would use the install all nxos bootflash:nxos.7.0.3.I4.1.bin command.

From To Limitations Recommended Procedure

7.0(3)I2(1) or later 7.0(3)I4(1) None install all is the recommended upgrade method supported.

6.0(2)U6(3) 7.0(3)I4(1) None install all is the only upgrade method supported because of a BIOS upgrade requirement.

Warning: Make sure that you 13

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

store the pre-Release, 6.0(2)U6(3)’s configuration file.

For more information, see the Cisco Nexus 3000 Series NX-OS Software Upgrade and Downgrade Guide, Release 7.x.

6.0(2)U6(2) or earlier

7.0(3)I4(1) First, upgrade to Cisco NX-OS Release 6.0(2)U6(3) or a later release.

Note: A Cisco Nexus 3048 switch requires an additional step when you upgrade from a software version older than Cisco NX-OS 6.0(2)U6(2), otherwise the switch can fail to boot. You must first upgrade the switch to Cisco NX-OS Release 6.0(2)U6(2), then to Cisco NX-OS Release 6.0(2)U6(3), and finally to Cisco NX-OS Release 7.0(3)I4(1).

install all is the only upgrade method supported because of a BIOS upgrade requirement.

For more information, see the Cisco Nexus 3000 Series NX-OS Software Upgrade and Downgrade Guide, Release 7.x.

LimitationsThe following are the known limitations for Cisco NX-OS Release 7.0(3)I4(1).

■ The fast reload feature is not supported.

■ Performing an ISSU is not supported on the following switches:

¯ Cisco Nexus 3132Q-V

¯ Cisco Nexus 31108PC-V

¯ Cisco Nexus 31108TC-V platforms

■ Subinterfaces cannot be used as network ports.

■ Cisco Nexus 3000-XL platforms do not support breakout using speed 10000 CLI command. Use the interface breakout module 1 port <num> map 10g-4x CLI command instead.

■ While installing the NXAPI https certificate that is present in the device, the following error message can appear if the user does not have the permission to install this certificate (See CSCup72219):

Certificate file read error.Please re-check permissions.

■ After configuring the NXAPI feature, the default http port (port 80) is still in the listening state even after we run the no nxapi http command. This results in the sandbox becoming accessible. Although the sandbox becomes accessible, HTTP requests from the sandbox to the device do not go through. Thus, the functionality is not affected. (See CSCup77051).

14

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

■ Chunking is enabled while displaying XML output for any CLI, and html tags (& lt; and & gt;) are displayed instead of < and > both on the sandbox and while running the Python script (See CSCup84801).

This is expected behavior. Each chunk should be in XML format for you to parse it and extract everything inside the <body> tag. This is done so that it can be later concatenated with similar output from all the chunks of the CLI XML output. After all the chunks are concatenated to get the complete XML output for the CLI, this complete XML output can be parsed for any parameter.

The following workaround is recommended to address this issue:

¯ Concatenate the <body> outputs from each chunk

¯ Replace all the html tags (& lt; and & gt;) with < and >

¯ Parse for any XML tag needed

■ If you use the write erase command, you cannot view the output for the show startup feature command. To view the startup configuration, you must then use the show startup-config command. This limitation will remain until you run the copy running-config startup-config command. After that, the show startup-config feature command will display the feature-only configuration output as expected (See CSCuq15638).

■ A Python traceback is seen while running the show xml command by using the Python shell. The exception type is httplib.IncompleteRead. This happens when you use Python scripts to leverage the NXAPI for retrieving switch data through XML or JSON. You should handle the exceptions in your Python scripts (See CSCuq19257).

■ While upgrading to a new release, when you create a checkpoint without running the setup script, the checkpoint file does not contain the copp-s-mpls class. After you run the write erase command and reload the switch, the copp-s-mpls class is created when the default configuration is applied. When a rollback is done to this checkpoint file, it detects a change in the CoPP policy and tries to delete all class-maps. Because you cannot delete static class-maps, this operation fails and, in turn, the rollback also fails.

This can also happen if you create a checkpoint, then create a new user-defined class and insert the new class before any other existing class (See CSCup56505).

The following workarounds are recommended to address this issue:

¯ Run setup after upgrading to a new release.

¯ Always insert the new classes at the end before a rollback.

■ When both the ip icmp-errors source and ip source intf icmp error commands are configured, then the command that is configured last takes effect.

Thereafter, if the last configured command is removed, the switch does not get configured with the command that was configured first.

■ Users who upgrade to 7.0(3)I4(1) need to run the set up script if they want to enable the MPLS static or the VRRpv3 feature.

■ The following Cisco Nexus 9000 features are not supported on the Cisco Nexus 3100 Series switches in N3K or N9K mode.

¯ FEX

¯ Network address translation (NAT)

¯ Multicast PIM Bidir15

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

¯ Support for up to 4000 VLANs

¯ Q-in-VNI support for VXLAN

¯ Q-in-Q support for VXLAN

¯ Port VLAN (PV) switching and routing support for VXLAN

¯ VXLAN BGP eVPN control plane

¯ Auto-Config

¯ Port profiles

¯ Secure login enhancements:

Ability to block login attempts and enforce a quiet period

Ability to restrict the maximum login sessions per user

Ability to restrict the password length

Ability to prompt the user to enter a password after entering the username

Ability to hide the shared secret used for RADIUS or TACACS+ authentication or accounting

SHA256 hashing support for encrypted passwords

¯ SHA256 algorithm to verify operating system integrity

¯ Non-hierarchical routing mode

¯ NX-API REST

■ Link Level Flow Control (LLFC) is not supported on Cisco Nexus 3000 series and Cisco Nexus 3100 series switches.

■ You can disable IGMP snooping either globally or for a specific VLAN.

■ You cannot disable IGMP snooping on a PIM enabled SVIs. The warning message displayed is: IGMP snooping cannot be disabled on a PIM enabled SVIs. There are one or more VLANs with PIM enabled.

MIB SupportThe Cisco Management Information Base (MIB) list includes Cisco proprietary MIBs and many other Internet Engineering Task Force (IETF) standard MIBs. These standard MIBs are defined in Requests for Comments (RFCs). To find specific MIB information, you must examine the Cisco proprietary MIB structure and related IETF-standard MIBs supported by the Cisco Nexus 3000 Series switch. The MIB Support List is available at the following FTP sites:

ftp://ftp.cisco.com/pub/mibs/supportlists/nexus3000/Nexus3000MIBSupportList.html

Related DocumentationDocumentation for the Cisco Nexus 3000 Series Switch is available at the following URL:

http://www.cisco.com/en/US/products/ps11541/tsd_products_support_series_home.html

16

Cisco Nexus 3000 Series NX-OS Release Notes, Release 7.0(3)I4(1)MIB Support

New DocumentationThere is no new documentation for this release.

Documentation FeedbackTo provide technical feedback on this document, or to report an error or omission, please send your comments to nexus3k-docfeedback@cisco.com. We appreciate your feedback.

Obtaining Documentation and Submitting a Service RequestFor information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

© 2016 Cisco Systems, Inc. All rights reserved.

17