· Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know...

41
SECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here ) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved PART 1 GENERAL 1.1 SECTION INCLUDES A. Automatic Sliding Doors including Operators and Control Devices. B. Automatic Hurricane Rated Sliding Doors including Operators and Control Devices. C. Automatic Cleanroom Rated Sliding Doors including Operators and Control Devices. 1.2 RELATED SECTIONS A. Section 07 90 00 - Joint Protection. B. Section 08 41 00 - Entrances and Storefronts. C. Section 08 71 53 - Security Door Hardware. D. Section 08 83 13 - Mirrored Glass Glazing. E. Section 26 05 19 - Low-Voltage Electrical Power Conductors and Cables. F. Section 26 05 00 - Common Work Results for Electrical. 1.3 REFERENCES A. ANSI A156.5 - Standard for Auxiliary Locks and Associated Products 08 42 29-1

Transcript of  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know...

Page 1:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

SECTION 08 42 29AUTOMATIC SLIDING DOORS

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Automatic Sliding Doors including Operators and Control Devices.

B. Automatic Hurricane Rated Sliding Doors including Operators and Control Devices.

C. Automatic Cleanroom Rated Sliding Doors including Operators and Control Devices.

1.2 RELATED SECTIONS

A. Section 07 90 00 - Joint Protection.

B. Section 08 41 00 - Entrances and Storefronts.

C. Section 08 71 53 - Security Door Hardware.

D. Section 08 83 13 - Mirrored Glass Glazing.

E. Section 26 05 19 - Low-Voltage Electrical Power Conductors and Cables.

F. Section 26 05 00 - Common Work Results for Electrical.

1.3 REFERENCES

A. ANSI A156.5 - Standard for Auxiliary Locks and Associated Products

B. ANSI A156.10 - Power Operated Pedestrian Doors.

C. ANSI-Z97.1.2 - Safety Performance Specifications and Methods of Test for Safety Glazing Materials Used in Buildings.

D. ASTM A 36 / A36 M - Standard Specification for Carbon Structural Steel.

08 42 29-1

Page 2:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

E. ASTM A 924 / A 924M - Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process.

F. ASTM B 209 - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate.

G. ASTM B 221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes.

H. ASTM E 283 - Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen.

I. ASTM E 330 - Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls By Uniform Static Air Pressure Difference.

J. ASTM F 842 - Standard Test Methods for Measuring the Forced Entry Resistance of Sliding Door Assemblies, Excluding Glazing Impact.

K. Aluminum Association Standard AA - Aluminum Finishes.

L. PA 201-94 - Large and Small Missile Impact Test. Dade County Code Compliance Protocols.

M. PA 202-94 - Uniform Static Pressure Test. Dade County Code Compliance Protocols.

N. PA 203-94 - Cyclic Wind Pressure Loading Test. Dade County Code Compliance Protocols.

O. NFPA 70 - National Electric Code.

P. NFPA 101 - Life Safety Code.

Q. UL 325 - Door, Drapery, Gate, Louver, and Window Operators and Systems - (UL) listed.

R. Intertek, Warnock Hersey (ETL) - Testing Laboratory and Certification Agency joined with ETL Semko.

S. UFC 4-010-01 - DOD Minimum Antiterrorism Standards for Buildings

1.4 DESIGN / PERFORMANCE REQUIREMENTS

A. Certifications: Automatic sliding door systems and options shall be factory certified to meet performance design criteria in accordance with the following standards:1. ANSI A156.10: For Power Operated Pedestrian Doors; Sliding Doors section.2. NFPA 101: Code for Safety to Life from Fire in Buildings & Structures.3. ETL Listed: Tested to UL 325 Standard4. BOCA: Means of Egress, Power Operated Doors5. ICBO/UBC: Egress Through Lobbies6. ICC/IBC: Egress Section

B. Operating Range: Minus 30 degrees F to 130 degrees F (Minus 34 degrees C to 54 degrees C).

C. Opening Force Requirements For Emergency Egress:1. Slide-swing panels shall require no more than 50 lbf. (222 N) of force to swing open.

Slide-swing panels shall be capable of swinging out 90 degrees from any position of slide movement.

2. Slide-swing panels and swing-out sidelites shall have torsion spring designed to re-close panel if pushed open in the direction of egress.

08 42 29-2

Page 3:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

3. If power fails, slide panels can be manually slid open with no more than 15 lbf (222 N) of force.

4. Units are ETL listed as an exit way and are compliant with NFPA 101.

D. Closing Force Requirements: Maximum force required to prevent sliding panel from closing 28 lbf. (124.5 N) Adjustable Reversing Circuit will reopen door unit if closing path is obstructed.

E. Accessibility Requirements: Comply with requirements of Local building code, and Americans with Disabilities Act (ADA), Accessibility Guidelines for Buildings and Facilities.

F. System Design/Profiler Series 2000B Elite-Plus: Operate, hold open, and close doors under design wind and suction loads calculated in accordance with applicable building code.

G. Electrical: 120 VAC, 50/60 cycle, single phase, dedicated 20 amp circuit per operator. Non-North American voltages can be 240 VAC 50/60 cycle except operator must have 240 volt power supply.

1.5 SUBMITTALS

A. Submit under provisions of Section 01 30 00 - Administrative Requirements.

B. Product Data: Manufacturer's data sheets on each product to be used, including:1. Preparation instructions and recommendations.2. Storage and handling requirements and recommendations.3. Installation methods.4. Operation and maintenance data.

C. Shop Drawings: Indicate layout and dimensions; head, jamb, and sill conditions; elevations; components, anchorage, adjacent construction interface, recesses, materials, and finishes, glazing details, electrical characteristics and connection requirements.

D. Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns.

E. Manufacturer's Certificates: Certify products meet or exceed specified requirements.

F. Manufacturers warranties.

G. Closeout: Submittals:1. Manufacturer's Warranty.2. Parts lists and maintenance instructions including data on operating hardware,

lubrication requirements, and inspection procedures related to preventative maintenance.

3. American Association of Automatic Door Manufacturers (AAADM) inspection form completed and signed by certified AAADM inspector prior to doors being placed into operation.

1.6 QUALITY ASSURANCE

A. Manufacturer Qualifications: Manufacturer to have minimum five years documented experience in the fabrication of automatic doors of the type required for this project and be capable of providing field service representation during installation.

B. Installer Qualifications: Installer to be experienced in the work of this section who has specialized in the installation of work similar to that required for this project.

08 42 29-3

Page 4:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

C. Certified Inspector: Copy of current AAADM Certification for AAADM inspector prior inspection.

1.7 DELIVERY, STORAGE, AND HANDLING

A. Package hardware items individually with necessary fasteners and installation templates when necessary; label and identify each package with door opening code to match door schedule.

B. Store products in manufacturer's unopened packaging until ready for installation.

C. Protect materials from exposure to moisture. Do not deliver until after wet work is complete and dry.

D. Store materials in a dry, warm, ventilated weathertight location.

1.8 PROJECT CONDITIONS

A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.

1.9 COORDINATION

A. Coordinate work with other directly affected components involving manufacture or fabrication of reinforcement for door hardware and recessed items.

B. Coordinate work with other directly affected components involving electrical wiring and components.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer: Horton Automatics division of Overhead Door Corporation, which is located at: 4242 Baldwin Blvd.; Corpus Christi, TX 78405-3399; Toll Free Tel: 800-531-3111; Tel: 361-888-5591; Fax: 800-531-3108; Email:request info ([email protected].); Web:http://www.hortondoors.com

B. Substitutions: Not permitted.

C. Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

2.2 AUTOMATIC SLIDING DOORS

A. Sliding Door System with Electric Belt Drive Operator: Horton Automatics Profiler Series 2000 with operator, header with roller track, carrier assemblies, framing, sliding door panel(s), sidelite(s), activation, safety devices and accessories required for complete installation.1. Model:

a. Sliding Door System with Electric Linear Drive Operator: Horton Automatics Profiler Series 2000.

b. Sliding Door System with Electric Belt Drive Operator: Horton Automatics Profiler Series 2000B Elite.

c. Sliding Door System with Electric Belt Drive Operator: Horton Automatics Profiler Series 2000B Elite-Plus.

2. Configuration:

08 42 29-4

Page 5:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

a. Single Slideb. Biparting

3. Mounting Type:a. Perimeter mounted within rough opening with sliding panel(s) sliding along

sidelite.b. Surface mounted with sliding panel(s) sliding along wall eliminating need for

sidelite.4. Door Type:

a. Type 010: Sliding panel(s) ' X' shall slide along interior side.b. Type 110: Slide-swing panel(s) ' SX' shall slide along exterior side.c. Type 310: Slide-swing panel(s) ' SX' shall slide along interior side. Unit has

Swing-out sidelite ' SO'.d. SpaceSaver: Dual single slide units with common sidelite. Slide-swing panel '

SX' slides along exterior of middle sidelite ' O' from one direction. Sliding panel ' X' slides along interior side from opposite direction.

5. Operator: Profiler Series 2000 Linear Drive. Operator shall be mounted and concealed within the header. Motor 1/8 HP DC permanent magnet working with a threadless, induction hardened stainless steel 1/2 inch (13 mm) diameter linear drive shaft. Maximum current draw shall not exceed 3.15 amps. A linear travel block describes a helical path along the rotating shaft utilizing six aircraft quality ball bearings acting as an integral clutch. Linear drive shaft is self lubricating.

6. Operator: Profiler Series 2000B Elite Belt Drive. Operator shall be mounted and concealed within the header. Motor 1/8 HP DC permanent magnet motor with worm gear transmission and 1800 RPM working with drive belt, attached door hangers, and idler pulley. Maximum draw shall not exceed 3.15 amps. Drive belt is steel reinforced nylon, 1/2 inch (13 mm) wide. Idler pulley is reinforced, metallic material.a. Master Control: 16 bit microprocessor controller with dual on-board seven-

segment alphanumeric diagnostic display and position encoder. Encoder shall monitor revolutions of the operator shaft and send signals to microprocessor controller to define door position and speed. Control shall have minimum of 28 programmable parameters including the following as required by ANSI A156.10:1) Adjustable opening and closing speeds.2) Adjustable back-check and latching.3) Adjustable braking.4) Adjustable hold-open time between 1 to 30 seconds.5) Adjustable Reversing Circuit will reopen door unit if closing path is

obstructed.6) Separate day and night modes of operation with security over-ride.

b. Finger Safety: Strike rail of sliding panel will stop short of adjacent sidelite; resulting opening is net slide.

c. On/Off Switch: When switched OFF or during electrical power failure, unit reverts to free manual operation.

7. Security and Safety Power Fail Options:a. Automatic lock: Automatically locks slide function of door when in closed

position. Additional power supply for autolock not acceptable.1) Autolock Fail Secure: If power fails the lock engages.2) Autolock Fail Safe: If power fails the lock disengages.

b. Monitored Power Fail Options (battery back-up):1) Software Selectable Power Fail Open: If power fails the door slides open.2) Software Selectable Power Fail Close: If power fails the door slides

closed.8. Profiler Header: Aluminum construction with extruded z-profile reinforcement for dead

load and lateral strength. Header has removable face plate for service and adjustment of operator and controls and mounts flush to 4 inch framing jambs.a. Slim 4 inches (102 mm) deep by 6 inches (152 mm) high aluminum

08 42 29-5

Page 6:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

construction with extruded z-profile reinforcement for dead load and lateral strength.

b. SpaceSaver headers shall be combined depth of 8 inches (203 mm) with removable face plate for each.

9. Header Capacity: Header shall be capable of supporting:a. Biparting: Up to 250 lbs. (113.4 kg) per slide panel over spans up to 16 feet 0

inches (4877 mm) without intermediate supports.b. Single Slide: Up to 350 lbs. (158.7 kg) per slide panel over spans up to 9 feet 0

inches (2743 mm) without intermediate supports.10. Carrier and Header Roller Track: Carrier assemblies support door panels with

minimum four rollers per panel. Rollers are steel, high quality ball bearing wheels 1-1/4 inch (32 mm) diameter. Anti-Derailing is accomplished by a continuous aluminum extrusion full length of slide panel travel. Overhead header roller track is continuous aluminum, nylon covered, and replaceable.

11. Sliding Panel(s) and Sidelite(s): Aluminum, 1-3/4 inches (44 mm) deep with narrow stile rails. An intermediate, horizontal rail (muntin bar), 2-1/4 inches (57 mm) wide, is furnished for safety and division of glass (optional on 010 units). Standard bottom rail shall be 4 inches (102 mm) tall. Sliding panels have concealed bottom guides to stabilize slide travel.a. Weather-stripping: Provide at perimeter of sliding panel(s) and swing-out

sidelite(s). Weatherstripping material is captured in extruded aluminum door panel. Surface applied self-adhesive weatherstripping not acceptable. Provide adjustable spring-loaded double astragal weather-stripping at lead edge, double mohair at interlock rails

b. Glazing prep to be for ___ glass thickness.c. Sliding Panel and Sidelite Options:

1) Medium stile construction: 3-3/4 inches (95 mm) wide vertical rails with 6-1/2 inches (165mm) tall bottom rail. Note: Medium stile construction will reduce slide opening.

2) Wide stile construction: 5 inches (127 mm) wide vertical rails with 6-1/2 inches (165mm) tall bottom rail. Note: Wide stile construction will reduce slide opening.

3) Surface applied push bar 1-1/2 inches (32 mm) wide in lieu of standard muntin bar.

4) Custom horizontal muntins from 1/2 inch (13 mm) to 10 inches (254 mm) wide.

5) Custom bottom rails up to 10 inches (254 mm) tall.6) Additional and/or extra wide sidelites of size and type indicated.7) Recessed sidelite and track and non-threshold application.8) Prep for glazing 5/16 inch (16 mm) to 1 inch (25 mm) as indicated on the

Drawings.12. Breakout Panels: Slide-swing panels can swing out minimum of 90 degrees from any

position of slide movement and require no more than 50 lbf. (222 N) of force applied at the lock stile to open. Slide-swing panels and swing-out sidelites shall utilize spring loaded ball detent.a. Slide-swing panels and swing-out sidelites shall have torsion spring designed to

re-close panel if pushed open in the direction of egress.b. Breakout mechanism shall provide support across full width of the door, in

normal operating mode. In breakout mode, torsion assembly shall support weight of the door to minimize drop during emergency egress.

c. Slide-swing panels shall include intermediate horizontal rail.d. Units with breakout feature are ETL listed as an exit away and are compliant

with NFPA 101.13. Jambs/Frame: Aluminum.

a. 1-3/4 inches (44 mm) deep by 4 inches (102 mm) wide.b. 1-3/4 inches (44 mm) deep by 4-1/2 inches (114 mm) wide.

08 42 29-6

Page 7:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

c. 1-3/4 inches (44 mm) deep by 6 inches (152 mm) wide. Maximum height: 8 feet 8 inches.

d. 2 inches (51 mm) deep by 6 inches (152 mm) wide. Maximum height: 8 feet 8 inches.

e. 4 inches (102 mm) square. Maximum height: 8 feet 8 inches.f. 1-3/4 inches (44 mm) deep by 8 inches (152 mm) wide for SpaceSaver.g. Transom of size and type indicated, mounted on header

14. Threshold: Shall be aluminuma. 1/2 inch (25 mm) tall by 4 inches (102 mm) wide.b. 7 inches (178 mm) wide.

15. Hardware:a. ANSI A156.5, Grade 1, 2-Point Locking provided and installed in strike rail shall

include:1) Hookbolt Latch, 5/8 inch laminated stainless steel, latching into jamb or

adjacent strike rail.2) 3/8 inch hex-bolt into breakout carrier frame.3) Keyed 1-5/32 inches (29 mm) Cylinder mounted on exterior side with

31/32 inch (25 mm) backset4) Thumbturn mounted on interior side.

b. ANSI A156.5, Grade 1, 3-Point locking for biparting doors shall include:1) Hookbolt Lock, 5/8 inch latching into jamb or adjacent strike rail.2) Maximum Security Lock with 31/32 inch (25 mm) backset.3) Keyed Cylinder mounted on exterior side with 1-5/32 inches (29 mm)

standard size cylinder.4) Thumbturn mounted on interior side.5) 3/8 inch lockbolt into breakout carrier frame and threshold.

c. Flush Panic Exit Device recessed in 6-1/2 inches muntin bar for door types 110 and 310.

d. Surface mounted Panic Exit Device for door type 310.16. Basic Sensor System: 24 VDC, class ll circuit adjusted and installed in compliance

with ANSI A156.10. System shall include the following:a. Activation Sensors: Microwave or active infrared sensor shall be header-

mounted each side of door unit for detection of traffic from each direction.b. Threshold Presence Sensors:

1) Header mounted sensors shall provide active infrared presence detection on each side of the door unit and shall remain active throughout the entire door opening and closing cycle.

2) Hold-open beams: Two pulsed infrared photoelectric beams to be mounted in vertical rails of sidelite or in jambs. Sender/receiver arrangement parallels door opening.

B. Sliding Door System with Electric Belt Drive Operator: Horton Automatics ProSlide Series 2003 with operator, header with roller track, carrier assemblies, framing, sliding door panel(s), sidelite(s), activation, safety devices and accessories required for complete installation.1. Model:

a. Sliding Door System with Electric Belt Drive Operator: Horton Automatics ProSlide Series 2003.

b. Sliding Door System with Electric Belt Drive Operator: Horton Automatics HD-Slide Series 2001.

2. Configuration:a. Single Slideb. Biparting

3. Mounting Type:a. Perimeter mounted within rough opening with sliding panel(s) sliding along

sidelite.

08 42 29-7

Page 8:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

b. Surface mounted with sliding panel(s) sliding along wall eliminating need for sidelite.

4. Door Type:a. Type 010: Sliding panel(s) ' X' shall slide along interior side.b. Type 110: Slide-swing panel(s) ' SX' shall slide along exterior side.c. Type 310: Slide-swing panel(s) ' SX' shall slide along interior side. Unit has

Swing-out sidelite ' SO'.d. Type 410: Slide-swing panel(s) ' SX' shall slide between fixed and swing-out

sidelite ' O/SO'e. SpaceSaver: Dual single slide units with common sidelite. Slide-swing panel '

SX' slides along exterior of middle sidelite ' O' from one direction. Sliding panel ' X' slides along interior side from opposite direction.

5. Operator: ProSlide Series 2003 Belt Drive. Operator shall be mounted and concealed within the header. Motor 1/8 HP DC permanent magnet motor with worm gear transmission and 1800 RPM working with drive belt, attached door hangers, and idler pulley. Maximum current draw shall not exceed 3.15 amps. Drive belt to be steel reinforced nylon, 1/2 inch (13 mm) wide. Idler pulley to be reinforced, metallic material.

6. Operator: HD-Slide Series 2001 Belt Drive. Operator shall be mounted and concealed within the header. Motor 1/8 HP DC permanent magnet motor with worm gear transmission and 1800 RPM working with reinforced drive belt, 1/4 inch thick steel door hangers, and idler pulley. Provide with 1/4 HP motor for door panels weighing 500 lbs. Maximum current draw shall not exceed 3.15 amps. Drive belt to be steel reinforced nylon, 1 inch (25 mm) wide. Idler pulley to be reinforced, metallic material.a. Master Control: 16 bit microprocessor controller with dual on-board seven-

segment alphanumeric diagnostic display and position encoder. Encoder shall monitor revolutions of the operator shaft and send signals to microprocessor controller to define door position and speed. Control shall have minimum of 28 programmable parameters including the following functions as required by ANSI A156.10:1) Adjustable opening and closing speeds.2) Adjustable back-check and latching.3) Adjustable braking.4) Adjustable hold-open time between 1 to 30 seconds.5) Adjustable Reversing Circuit will reopen door unit if closing path is

obstructed.6) Separate day and night modes of operation with security over-ride.

b. Finger Safety: Strike rail of sliding panel will stop short of adjacent sidelite; resulting opening is net slide.

c. On/Off Switch: When switched OFF or during electrical power failure, unit reverts to free manual operation.

7. Security and Safety Power Fail Options:a. Automatic lock: Automatically locks slide function of door when in closed

position. Additional power supply for autolock not acceptable.1) Autolock Fail Secure: If power fails the lock engages.2) Autolock Fail Safe: If power fails the lock disengages.

b. Monitored Power Fail Options (battery back-up):1) Software Selectable Power Fail Open: If power fails the door slides open.2) Software Selectable Power Fail Close: If power fails the door slides

closed.8. Header:

a. ProSlide Header: Aluminum construction 6 inches (152 mm) deep by 6 inches (152 mm) high with removable face plate for service and adjustment of operator and controls. Header mounts flush to one side of framing jambs. SpaceSaver headers shall be combined depth of 12 inches (306 mm) with removable face plate for each.

08 42 29-8

Page 9:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

b. HD-Slide Header: Heavy duty aluminum construction, 6 inches (152 mm) deep by 8 inches (203 mm) high, with removable face plate and extruded support brackets for dead load and lateral strength.

9. Header Capacity: Header shall be capable of supporting:a. Biparting: Up to 250 lbs. (113.4 kg) per slide panel over spans up to 16 feet 0

inches (4877 mm) without intermediate supports.10. Carrier and Header Roller Track: Carrier assemblies support door panels with

minimum four rollers per panel. Rollers are steel, high quality ball bearing wheels. Anti-Derailing is accomplished by a continuous aluminum extrusion full length of slide panel travel. Overhead header roller track is continuous aluminum, nylon covered, and replaceable.

11. Sliding Panel(s) and Sidelite(s): Aluminum, 1-3/4 inches (44 mm) deep with narrow stile rails. An intermediate, horizontal rail (muntin bar), 2-1/4 inches (57 mm) wide, is furnished for safety and division of glass (optional on 010 units). Standard bottom rail shall be 4 inches (102 mm) tall. Sliding panels have concealed bottom guides to stabilize slide travel.a. Weather-stripping: Provide at perimeter of sliding panel(s) and swing-out

sidelite(s). Weatherstripping material is captured in extruded aluminum door panel. Surface applied self-adhesive weatherstripping not acceptable. Provide adjustable spring-loaded double astragal weather-stripping at lead edge, double mohair at interlock rails

b. Sliding Panel and Sidelite Options:1) Medium stile construction: 3-3/4 inches (95 mm) wide vertical rails with 6-

1/2 inches (165mm) tall bottom rail. Note: Medium stile construction will reduce slide opening.

2) Wide stile construction: 5 inches (127 mm) wide vertical rails with 6-1/2 inches (165mm) tall bottom rail. Note: Wide stile construction will reduce slide opening.

3) Surface applied push bar 1-1/2 inches (32 mm) wide in lieu of standard muntin bar.

4) Custom horizontal muntins from 1/2 inch (13 mm) to 10 inches (254 mm) wide.

5) Custom bottom rails up to 10 inches (254 mm) tall.6) Additional and/or extra wide sidelites of size and type indicated.7) Recessed sidelite and track and non-threshold application.8) Glazing prep to be for ___ glass thickness.

12. Breakout Panels: Slide-swing panels can swing out minimum of 90 degrees from any position of slide movement and require no more than 50 lbf. (222 N) of force applied at the lock stile to open. Slide-swing panels and swing-out sidelites shall utilize spring loaded ball detent.a. Slide-swing panels and swing-out sidelites shall have torsion spring designed to

re-close panel if pushed open in the direction of egress.b. Breakout mechanism shall provide support across full width of the door, in

normal operating mode. In breakout mode, torsion assembly shall support weight of the door to minimize drop during emergency egress.

c. Slide-swing panels shall include intermediate horizontal rail.d. Units with breakout feature are ETL listed as an exit away and are compliant

with NFPA 101.13. Jambs/Frame: Aluminum.

a. 1-3/4 inches (44 mm) deep by 4 inches (102 mm) wide.b. 1-3/4 inches (44 mm) deep by 4-1/2 inches (114 mm) wide.c. 1-3/4 inches (44 mm) deep by 6 inches (152 mm) wide. Maximum height: 8 feet

8 inches.d. 2 inches (51 mm) deep by 6 inches (152 mm) wide. Maximum height: 8 feet 8

inches.e. 4 inches (102 mm) square. Maximum height: 8 feet 8 inches.

08 42 29-9

Page 10:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

f. Transom of size and type indicated, mounted on header14. Threshold: Shall be aluminum

a. 1/2 inch (25 mm) tall by 4 inches (102 mm) wide.b. 7 inches (178 mm) wide.

15. Hardware:a. ANSI A156.5, Grade 1, 2-Point Locking provided and installed in strike rail shall

include:1) Hookbolt Latch, 5/8 inch laminated stainless steel, latching into jamb or

adjacent strike rail.2) 3/8 inch hex-bolt into breakout carrier frame.3) Keyed 1-5/32 inches (29 mm) Cylinder mounted on exterior side with

31/32 inch (25 mm) backset4) Thumbturn mounted on interior side.

b. ANSI A156.5, Grade 1, 3-Point locking for biparting doors shall include:1) Hookbolt Lock, 5/8 inch latching into jamb or adjacent strike rail.2) Maximum Security Lock with 31/32 inch (25 mm) backset.3) Keyed Cylinder mounted on exterior side with 1-5/32 inches (29 mm)

standard size cylinder.4) Thumbturn mounted on interior side.5) 3/8 inch lockbolt into breakout carrier frame and threshold.

c. Flush Panic Exit Device recessed in 6-1/2 inches muntin bar for door types 110 and 310.

d. Surface mounted Panic Exit Device for door type 310.16. Basic Sensor System: 24 VDC, class ll circuit adjusted and installed in compliance

with ANSI A156.10. System shall include the following:a. Activation Sensors: Microwave or active infrared sensor shall be header-

mounted each side of door unit for detection of traffic from each direction.b. Threshold Presence Sensors:

1) Header mounted sensors shall provide active infrared presence detection on each side of the door unit and shall remain active throughout the entire door opening and closing cycle.

2) Hold-open beams: Two pulsed infrared photoelectric beams to be mounted in vertical rails of sidelite or in jambs. Sender/receiver arrangement parallels door opening.

C. Sliding Door System with Electric Belt Drive Operator: Horton Automatics All Glass Elegant Series 2500 with operator, header with roller track, carrier assemblies, framing, sliding door panel(s), sidelite(s), activation, safety devices and accessories required for complete installation.1. Model:

a. Sliding Door System with Electric Belt Drive Operator: Horton Automatics All Glass Elegant Series 2500.

2. Configuration:a. Single Slideb. Biparting

3. Mounting Type:a. Perimeter mounted within rough opening with sliding panel(s) sliding along

sidelite.4. Door Type:

a. Type 010: Sliding panel(s) ' X' shall slide along interior side.b. Type 110: Slide-swing panel(s) ' SX' shall slide along exterior side.c. Type 310: Slide-swing panel(s) ' SX' shall slide along interior side. Unit has

Swing-out sidelite ' SO'.5. Operator: HD-Slide Series 2001 Belt Drive. Operator shall be mounted and concealed

within the header. Motor 1/8 HP DC permanent magnet motor with worm gear transmission and 1800 RPM working with reinforced drive belt, 1/4 inch thick steel

08 42 29-10

Page 11:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

door hangers, and idler pulley. Provide with 1/4 HP motor for door panels weighing 500 lbs. Maximum current draw shall not exceed 3.15 amps. Drive belt to be steel reinforced nylon, 1 inch (25 mm) wide. Idler pulley to be reinforced, metallic material.a. Master Control: 16 bit microprocessor controller with dual on-board seven-

segment alphanumeric diagnostic display and position encoder. Encoder shall monitor revolutions of the operator shaft and send signals to microprocessor controller to define door position and speed. Control shall have minimum of 28 programmable parameters including the following functions as required by ANSI A156.10:1) Adjustable opening and closing speeds.2) Adjustable back-check and latching.3) Adjustable braking.4) Adjustable hold-open time between 1 to 30 seconds.5) Adjustable Reversing Circuit will reopen door unit if closing path is

obstructed.6) Separate day and night modes of operation with security over-ride.

b. Finger Safety: Strike rail of sliding panel will stop short of adjacent sidelite; resulting opening is net slide.

c. On/Off Switch: When switched OFF or during electrical power failure, unit reverts to free manual operation.

6. Security and Safety Power Fail Options:a. Automatic lock: Automatically locks slide function of door when in closed

position. Additional power supply for autolock not acceptable.1) Autolock Fail Secure: If power fails the lock engages.2) Autolock Fail Safe: If power fails the lock disengages.

b. Monitored Power Fail Options (battery back-up):1) Software Selectable Power Fail Open: If power fails the door slides open.2) Software Selectable Power Fail Close: If power fails the door slides

closed.7. Header: HD-Slide Header: Heavy duty aluminum construction, 6 inches (152 mm)

deep by 8 inches (203 mm) high, with removable face plate and extruded support brackets for dead load and lateral strength.

8. Header Capacity: Header shall be capable of supporting:a. Biparting: Up to 300 lbs. (136 kg) per slide panel over spans up to 14 feet 0

inches (4280 mm) without intermediate supports.b. Single Slide: Up to 500 lbs. (227 kg) per slide panel over spans up to 9 feet 0

inches (2743 mm) without intermediate supports.9. Carrier and Header Roller Track: Carrier assemblies support door panels with

minimum four rollers per panel. Rollers are steel, high quality ball bearing wheels. Anti-Derailing is accomplished by a continuous aluminum extrusion full length of slide panel travel. Overhead header roller track is continuous aluminum, nylon covered, and replaceable.

10. Sliding Panel(s) and Sidelite(s): 1/2 inch (13 mm) thick tempered glass with polished vertical edges mounted in top and bottom horizontal aluminum rails. Weather-stripping retained in top and bottom rails and in clear acrylic extrusions mounted along vertical edges of sliding glass panel.a. Sliding Panel and Sidelite Options:

1) Extra wide fixed sidelite(s) of size and type indicated.2) Recessed sidelite and track and non-threshold application.

11. Breakout Panels: Slide-swing panels can swing out minimum of 90 degrees from any position of slide movement and require no more than 50 lbf. (222 N) of force applied at the lock stile to open. Slide-swing panels and swing-out sidelites shall utilize spring loaded ball detent.a. Slide-swing panels and swing-out sidelites shall have torsion spring designed to

re-close panel if pushed open in the direction of egress.b. Breakout mechanism shall provide support across full width of the door, in

08 42 29-11

Page 12:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

normal operating mode. In breakout mode, torsion assembly shall support weight of the door to minimize drop during emergency egress.

c. Units with breakout feature are UL listed as an exit away and are compliant with NFPA 101.

12. Jambs/Frame: Aluminum.a. 1-3/4 inches (44 mm) deep by 4-1/2 inches (114 mm) wide.b. 1-3/4 inches (44 mm) deep by 6 inches (152 mm) wide. Maximum height: 8 feet

8 inches.c. Transom of size and type indicated, mounted on header

13. Threshold: Shall be aluminuma. 1/2 inch (25 mm) tall by 4 inches (102 mm) wide.b. 7 inches (178 mm) wide.

14. Hardware:a. Bottom rail Maximum Security Lock with 31/32 inch (25 mm) backset and Two-

point keyed 1-5/32 inch (29 mm) standard size cylinder. Deadlock dropbolt into threshold

15. Basic Sensor System: 24 VDC, class ll circuit adjusted and installed in compliance with ANSI A156.10. System shall include the following:a. Activation Sensors: Microwave or active infrared sensor shall be header-

mounted each side of door unit for detection of traffic from each direction.b. Threshold Presence Sensors:

1) Header mounted sensors shall provide active infrared presence detection on each side of the door unit and shall remain active throughout the entire door opening and closing cycle.

2) Hold-open beams: Two pulsed infrared photoelectric beams to be mounted in vertical rails of sidelite or in jambs. Sender/receiver arrangement parallels door opening.

D. Telescoping Door System with Electric Belt Drive Operator: Horton Automatics ProSlide Series 2003T with operator, header with roller track, carrier assemblies, framing, sliding door panel(s), sidelite(s), activation, safety devices and accessories required for complete installation. Leading slide panel will open twice as fast as adjacent sliding panel1. Configuration:

a. Single Telescoping, 3 panels.b. Biparting, 6 panels.

2. Mounting Type:a. Perimeter mounted within rough opening with sliding panel(s) sliding along

sidelite.b. Surface mounted with sliding panel(s) sliding along wall eliminating need for

sidelite.3. Door Type:

a. Type 010: Sliding panel(s) ' X' shall slide along interior side.b. Type 110: Slide-swing panel(s) ' SX' shall slide along exterior side.c. Type 310: Slide-swing panel(s) ' SX' shall slide along interior side. Unit has

Swing-out sidelite ' SO'.4. Operator: ProSlide Telescoping Series 2003T Belt Drive. Operator shall be mounted

and concealed within the header.a. Motor: 1/8 HP DC permanent magnet motor with worm gear transmission and

1800 RPM working with drive belt, attached door hangers, and idler pulley. Maximum current draw shall not exceed 3.15 amps. Drive belt to be steel reinforced nylon, 1/2 inch (13 mm) wide. Idler pulley to be reinforced, metallic material.

b. Master Control: 16 bit microprocessor controller with dual on-board seven-segment alphanumeric diagnostic display and position encoder. Encoder shall monitor revolutions of the operator shaft and send signals to microprocessor controller to define door position and speed. Controller shall have minimum of

08 42 29-12

Page 13:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

28 programmable parameters including the following functions:1) Adjustable opening and closing speeds.2) Adjustable back-check and latching.3) Adjustable braking.4) Adjustable hold-open time between 1 to 30 seconds.5) Adjustable Reversing Circuit will reopen door unit if closing path is

obstructed.6) Separate day and night modes of operation with security over-ride.

c. Finger Safety: When unit slides open, strike rail of sliding panel will stop short of adjacent sidelite; resulting opening is net slide.

d. On/Off Switch: When switched OFF or during electrical power failure, unit reverts to free manual operation.

5. Security and Safety Power Fail Options:a. Automatic lock: Automatically locks slide function of door when in closed

position. Additional power supply for autolock not acceptable.1) Autolock Fail Secure: If power fails the lock engages.2) Autolock Fail Safe: If power fails the lock disengages.

b. Monitored Power Fail Options battery back-up:1) Power Fail Open: If power fails the door slides open.2) Autolock Fail Safe: If power fails the lock disengages.

6. Telescoping Header: 8 inches (152 mm) deep by 6 inches (152 mm) high. Header shall be aluminum construction with removable face plate.

7. Header Capacity: Header shall be capable of supporting:a. Telescoping: Up to 90 lbs. (40.8 kg) per slide panel over spans up to 14 feet 0

inches (4267 mm) without intermediate supports.8. Carrier and Header Roller Track: Double track system that provides for two-speed

travel of sliding panels. Carrier assemblies support door panels with four rollers per panel. Rollers are non-metallic, high quality ball bearing wheels 2 inches (51 mm) diameter. Anti-Derailing is accomplished by means of two additional adjustable rollers per panel. Overhead header roller track shall be continuous aluminum and replaceable.

9. Sliding Panel(s) and Sidelite(s): Aluminum, 1-3/4 inches (44 mm) deep with narrow stile rails. An intermediate, horizontal rail (muntin bar), 2-1/4 inches (57 mm) wide, shall be furnished for safety and division of glass (optional on 010 units). Standard bottom rail shall be 4 inches (102 mm) tall. Slide panels to have synchronizing cable and speed regulating mechanism. Sliding panels shall have concealed bottom guides to stabilize slide travel.a. Weather-stripping at perimeter of sliding panel(s) and swing-out sidelite(s).

Weatherstripping material captured in extruded aluminum door panel. Surface applied self-adhesive weatherstripping not acceptable. Adjustable spring-loaded double astragal weather-stripping at lead edge, double mohair at interlock rails

b. Medium stile construction: 3-3/4 inches (95 mm) wide vertical rails with 6-1/2 inches (165 mm) tall bottom rail. Note: Medium stile construction will reduce slide opening.

c. Wide stile construction: 5 inches (127 mm) wide vertical rails with 6-1/2 inches (165 mm) tall bottom rail. Note: Wide stile construction will reduce slide opening.

d. Surface applied push bar 1-1/2 inches (32 mm) wide in lieu of standard muntin bar.

e. Custom horizontal muntins from 1/2 inch (13 mm) to 10 inches (254mm) wide.f. Custom bottom rails up to 10 inches (254 mm) tall.g. Additional and/or extra wide sidelites of size and type indicated.h. Recessed sidelite and track and non-threshold application.i. Glazing prep to be for ___ glass thickness.

10. Breakout Panels: Slide-swing panels can swing out minimum of 90 degrees from any

08 42 29-13

Page 14:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

position of slide movement and require no more than 50 lbf. (222 N) of force applied at the lock stile to open. Slide-swing panels and swing-out sidelites shall utilize spring loaded ball detent.a. Slide-swing panels and swing-out sidelites shall have torsion spring designed to

re-close panel if pushed open in the direction of egress.b. Breakout mechanism shall provide support across full width of the door, in

normal operating mode. In breakout mode, torsion assembly shall support weight of the door to minimize drop during emergency egress.

c. Slide-swing panels shall include intermediate horizontal rail.d. Units with breakout feature are ETL listed as an exit away and are compliant

with NFPA 101.11. Jambs/Frame: Aluminum 1-3/4 inches (44 mm) deep by 6 inches (152 mm) wide.12. Threshold: Shall be aluminum

a. 1/2 inch (25 mm) tall by 4 inches (102 mm) wide.b. 7 inches (178 mm) wide.

13. Hardware:a. ANSI A156.5, Grade 1, 2-Point Locking provided and installed in strike rail shall

include:1) Hookbolt Latch, 5/8 inch laminated stainless steel, latching into jamb or

adjacent strike rail.2) 3/8 inch hex-bolt into breakout carrier frame.3) Keyed 1-5/32 inches (29 mm) Cylinder mounted on exterior side with

31/32 inch (25 mm) backset4) Thumbturn mounted on interior side.

b. ANSI A156.5, Grade 1, 3-Point locking for biparting doors shall include:1) Hookbolt Lock, 5/8 inch latching into jamb or adjacent strike rail.2) Maximum Security Lock with 31/32 inch (25 mm) backset.3) Keyed Cylinder mounted on exterior side with 1-5/32 inches (29 mm)

standard size cylinder.4) Thumbturn mounted on interior side.5) 3/8 inch lockbolt into breakout carrier frame and threshold.

c. Flush Panic Exit Device recessed in 6-1/2 inches muntin bar for door types 110 and 310.

d. Surface mounted Panic Exit Device for door type 310.14. Basic Sensor System: 24 VDC, class ll circuit adjusted and installed in compliance

with ANSI A156.10. System shall include the following:a. Activation Sensors: Microwave or active infrared sensor shall be header-

mounted each side of door unit for detection of traffic from each direction.b. Threshold Presence Sensors:

1) Header mounted sensors shall provide active infrared presence detection on each side of the door unit and shall remain active throughout the entire door opening and closing cycle.

2) Hold-open beams: Two pulsed infrared photoelectric beams to be mounted in vertical rails of sidelite or in jambs. Sender/receiver arrangement parallels door opening.

E. Lead Lined Telescoping Door System with Electric Belt Drive Operator: Horton Automatics ProSlide Series 2003T-LL with operator, header with roller track, carrier assemblies, framing, sliding door panel(s), sidelite(s), activation, safety devices and accessories required for complete installation. Leading slide panel will open twice as fast as adjacent sliding panel1. Configuration: Telescoping

a. ' P-X-X' handing as viewed from face plate side.b. ' X-X-P' (handing as viewed from face plate side.

2. Mounting Type:a. Surface mounted with sliding panel(s) sliding along wall eliminating need for

sidelite.

08 42 29-14

Page 15:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

3. Door Type:a. Type 010T: Sliding panels sliding along wall.

4. Operator: ProSlide Telescoping Series 2003T Belt Drive. Operator shall be mounted and concealed within the header.a. Motor: 1/8 HP DC permanent magnet motor with worm gear transmission and

1800 RPM working with drive belt, attached door hangers, and idler pulley. Maximum current draw shall not exceed 3.15 amps. Drive belt to be steel reinforced nylon, 1/2 inch (13 mm) wide. Idler pulley to be reinforced, metallic material.

b. Master Control: 16 bit microprocessor controller with dual on-board seven-segment alphanumeric diagnostic display and position encoder. Encoder shall monitor revolutions of the operator shaft and send signals to microprocessor controller to define door position and speed. Controller shall have minimum of 28 programmable parameters including the following functions:1) Adjustable opening and closing speeds.2) Adjustable back-check and latching.3) Adjustable braking.4) Adjustable hold-open time between 1 to 30 seconds.5) Adjustable Reversing Circuit will reopen door unit if closing path is

obstructed.6) Separate day and night modes of operation with security over-ride.

c. On/Off Switch: When switched OFF or during electrical power failure, unit reverts to free manual operation.

5. Security and Safety Power Fail Options:a. Automatic lock: Automatically locks slide function of door when in closed

position. Additional power supply for autolock not acceptable.1) Autolock Fail Secure: If power fails the lock engages.2) Autolock Fail Safe: If power fails the lock disengages.

b. Uninterrupted Power Supply (UPS) battery back-up:1) Power Fail Open: If power fails the door slides open.2) Autolock Fail Safe: If power fails the lock disengages.

6. Telescoping Header: 8 inches (152 mm) deep by 6 inches (152 mm) high. Header shall be aluminum construction with removable face plate.

7. Header Capacity: Header shall be capable of supporting:a. Telescoping: Up to __ lbs. (___ kg) per slide panel over spans up to __ feet 0

inches (____ mm) without intermediate supports.8. Carrier and Header Roller Track: Double track system that provides for two-speed

travel of sliding panels. Carrier assemblies support door panels with four rollers per panel. Rollers are non-metallic, high quality ball bearing wheels 2 inches (51 mm) diameter. Anti-Derailing is accomplished by means of two additional adjustable rollers per panel. Overhead header roller track shall be continuous aluminum and replaceable.

9. Sliding Panel(s) and Sidelite(s): Aluminum, 1-3/4 inches (44 mm) deep with medium stile rails with a structural core of resin impregnated Kraft honeycomb. Panels provided with 1/16 inch factory lead lining, vinyl weatherstripping and nylon sweeps and clad all around with stainless steel or aluminum. Sliding panels shall have concealed bottom guides to stabilize slide travel.a. Provide door with vision lite of 5/16 inch leaded glass glazing with maximum

size of 15-3/4 inches by 15-3/4 inches (400 mm by 400 mm).10. Breakout Panels: Slide-swing panels can swing out minimum of 90 degrees from any

position of slide movement and require no more than 50 lbf. (222 N) of force applied at the lock stile to open. Slide-swing panels and swing-out sidelites shall utilize spring loaded ball detent.a. Slide-swing panels and swing-out sidelites shall have torsion spring designed to

re-close panel if pushed open in the direction of egress.b. Breakout mechanism shall provide support across full width of the door, in

08 42 29-15

Page 16:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

normal operating mode. In breakout mode, torsion assembly shall support weight of the door to minimize drop during emergency egress.

c. Slide-swing panels shall include intermediate horizontal rail.d. Units with breakout feature are ETL listed as an exit away and are compliant

with NFPA 101.11. Jambs/Frame: Aluminum 1-3/4 inches (44 mm) deep by 6 inches (152 mm) wide.12. Activating Device: 24 VAC, Class ll circuit. Switch to be located on each side of the

opening and shall be one of the following:a. Touchless wall mounted switch or jamb mounted using diffused scanning

technology with adjustable range up to 15 inches (381 mm). Junction box included.

b. Motion Sensor: Mounted above opening on header or wall.c. Push Plate Wall Switch: Momentary contact switch, 6-1/4 inch (159 mm)

diameter stainless steel plate on standard junction box.13. Threshold Presence Sensors:

a. Header mounted sensors with active infrared presence detection on each side of the door unit that shall remain active throughout the entire door opening and closing cycle.

b. Hold-open beams: Two pulsed infrared photoelectric beams to be mounted in vertical rails of sidelite or in jambs. Sender/receiver arrangement parallels door opening.

F. Lead Lined Sliding Door System with Electric Belt Drive Operator: Horton Automatics HD-Slide Series 2001-LL with operator, header with roller track, carrier assemblies, framing, sliding door panel(s), activation, safety devices and accessories required for complete installation.1. Configuration: Sliding

a. Single Slide ' P-X' or ' X-P' handing as viewed from face plate side.b. Biparting ' P-X-X-P'

2. Mounting Type:a. Surface mounted.

3. Door Type:a. Type 010: Sliding panels X sliding along wall.

4. Operator: HD-Slide Telescoping Series 2001 Belt Drive. Operator shall be mounted and concealed within the header.a. Motor: 1/4 HP DC permanent magnet motor with worm gear transmission and

1800 RPM working with reinforced drive belt, attached 1/4 inch steel door hangers, and idler pulley. Maximum current draw shall not exceed 3.15 amps. Drive belt to be steel reinforced nylon, 1 inch (25.4 mm) wide. Idler pulley to be reinforced, metallic material.

b. Master Control: 16 bit microprocessor controller with dual on-board seven-segment alphanumeric diagnostic display and position encoder. Encoder shall monitor revolutions of the operator shaft and send signals to microprocessor controller to define door position and speed. Controller shall have minimum of 28 programmable parameters including the following functions:1) Adjustable opening and closing speeds.2) Adjustable back-check and latching.3) Adjustable braking.4) Adjustable hold-open time between 1 to 30 seconds.5) Adjustable Reversing Circuit will reopen door unit if closing path is

obstructed.6) Separate day and night modes of operation with security over-ride.

c. On/Off Switch: When switched OFF or during electrical power failure, unit reverts to free manual operation.

5. Security and Safety Power Fail Options:a. Automatic lock: Automatically locks slide function of door when in closed

08 42 29-16

Page 17:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

position. Additional power supply for autolock not acceptable.1) Autolock Fail Secure: If power fails the lock engages.2) Autolock Fail Safe: If power fails the lock disengages.

b. Uninterrupted Power Supply (UPS) battery back-up:1) Power Fail Open: If power fails the door slides open.2) Autolock Fail Safe: If power fails the lock disengages.

6. HD-Slide Header: 6 inches (152 mm) deep by 8 inches (203 mm) high, heavy duty aluminum construction with removable face plate and extruded support brackets for dead load and lateral strength.

7. Header Capacity: Header shall be capable of supporting:a. Telescoping: Up to __ lbs. (___ kg) per slide panel over spans up to __ feet 0

inches (____ mm) without intermediate supports.8. Carrier and Header Roller Track: Carrier assemblies support door panels with

minimum four rollers per panel. Rollers are non-metallic high quality ball bearing wheels 2 inches (51 mm) diameter. Anti-Derailing is accomplished by a continuous aluminum extrusion full length of slide panel travel. Overhead header roller track is continuous aluminum and replaceable.

9. Sliding Panel(s) and Sidelite(s): Aluminum, 1-3/4 inches (44 mm) deep with medium stile rails with a structural core of resin impregnated Kraft honeycomb. Panels provided with 1/16 inch factory lead lining, vinyl weatherstripping and nylon sweeps and clad all around with stainless steel or aluminum. Sliding panels shall have concealed bottom guides to stabilize slide travel.a. Provide door with vision lite of 5/16 inch leaded glass glazing with maximum

size of 15-3/4 inches by 15-3/4 inches (400 mm by 400 mm).10. Jambs/Frame: Aluminum 1-3/4 inches (44 mm) deep by 4 inches (102 mm) wide.11. Activating Device: 24 VAC, Class ll circuit. Switch to be located on each side of the

opening and shall be one of the following:a. Touchless wall mounted switch or jamb mounted using diffused scanning

technology with adjustable range up to 15 inches (381 mm). Junction box included.

b. Motion Sensor: Mounted above opening on header or wall.c. Push Plate Wall Switch: Momentary contact switch, 6-1/4 inch (159 mm)

diameter stainless steel plate on standard junction box.12. Threshold Presence Sensors:

a. Header mounted sensors with active infrared presence detection on each side of the door unit that shall remain active throughout the entire door opening and closing cycle.

b. Hold-open beams: Two pulsed infrared photoelectric beams to be mounted in vertical rails of sidelite or in jambs. Sender/receiver arrangement parallels door opening.

G. Steel Reinforced Sliding Blast Door System with Electric Belt Drive Operator: Horton Automatics ProSlide Blast Series UFC 4-010-01 with heavy duty operator, header and track, jambs, sliding door panel(s), sidelite(s), activation, safety devices and accessories required for complete installation.1. Configuration: Sliding

a. Type 010: Single Slide panel(s) ' X' slides along interior side of fixed sidelte(s) ' O'. Units will be either single-slide or bipart. Meets UFC 4-010-01 DOD Minimum Antiterrorism Standards for Buildings.

2. Mounting Type:a. Perimeter mounted within rough opening.

3. Operator: ProSlide Telescoping Series 2003T Belt Drive. Operator shall be mounted and concealed within the header. Motor 1/8 HP DC permanent magnet motor with worm gear transmission and 1800 RPM working with reinforce drive belt, attached 1/4 inch thick door hangers, and idler pulley. Maximum current draw shall not exceed 3.15 amps. A 1/4 HP motor is required for door panels weighing 500 lbs. Drive belt to be

08 42 29-17

Page 18:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

steel reinforced nylon, 1 inch (25.4 mm) wide. Idler pulley to be reinforced, metallic material.a. Master Control: Version 10 software and have dual on-board seven-segment

diagnostic display. Control shall have minimum of 28 programmable parameters including those functions required by ANSI A156.10. Control includes separate day and night modes of operation with security over-ride. Adjustable Reversing Circuit will reopen door unit if closing path is obstructed. Maximum force required to prevent sliding panel from closing = 28 lbf.

b. Finger Safety: When unit slides open, strike rail of sliding panel will stop short of adjacent sidelite; resulting opening is net slide

c. On/Off Switch: When switched OFF or during electrical power failure, unit reverts to free manual operation.

4. Security and Safety Power Fail Options:a. Automatic lock: Automatically locks slide function of door when in closed

position. Additional power supply for autolock not acceptable.1) Autolock Fail Secure: If power fails the lock engages.2) Autolock Fail Safe: If power fails the lock disengages.

b. Monitored Power Supply battery back-up:1) Power Fail Open: If power fails the door slides open.2) Autolock Fail Safe: If power fails the lock disengages.

5. Proslide Header: Steel reinforced 6 inches (152 mm) deep by 6 inches (152 mm) high aluminum construction with removable face plate for service and adjustment of operator and controls

6. Header Capacity: Header shall be capable of supporting:a. Telescoping: Up to __ lbs. (___ kg) per slide panel over spans up to __ feet 0

inches (____ mm) without intermediate supports.7. Door Rollers: Polymer and replaceable. Rollers are non-metallic, high quality ball

bearing wheels 2 inches (51 mm) diameter. Anti-Derailing is accomplished by a separate adjustable roller.

8. Sliding Panel(s) and Sidelite(s): Aluminum, 1-3/4 inches (44 mm) deep with medium stile rails. Bottom rail is 6-1/2 inches (165 mm) tall. Weather-stripping to be along perimeter of sliding panel(s) and sidelite(s). Concealed guides to stabilize bottom of sliding panel. All vertical rails shall be steel reinforced for UFC 4-010-01 compliance. Interior heavy duty glass stops to be fixed.a. Total weight limit per panel shall be 500 lbs (227 kg) for non-breakout single

slide and 300 lbs (136 kg) for non-breakout bipartb. Standard glazing prep shall be 9/16 inch laminated glass: 1/4 inch heat

strengthened (2 layers); 0.075 Solutia Vanceva composite layer. Wet glazed with Dow Corning #995

9. Emergency Egress: Comply with requirements of authorities having jurisdiction for automatic doors serving as a required means of egress. Unit is designed for blast resistance requiring that active panels slide only and not breakout. Opening force: If power fails not more than 50 lbf (222 N) manual force required to set door in motion and not more than 15 lbf (67 N) to slide to minimum clear walk-thru width

10. Jambs/Frame: Aluminum 2 inches (25.4 mm) deep by 6 inches (152 mm) wide.11. Threshold: Shall be aluminum

a. 1/2 inch (25 mm) tall by 4 inches (102 mm) wide.b. 7 inches (178 mm) wide.

12. Hardware:a. AANSI A156.5, Grade 1, 3-Point locking for biparting doors shall include:

1) Hookbolt Lock, 5/8 inch latching into jamb or adjacent strike rail.2) Maximum Security Lock with 31/32 inch (25 mm) backset.3) Keyed Cylinder mounted on exterior side with 1-5/32 inches (29 mm)

standard size cylinder.4) Thumbturn mounted on interior side.5) 3/8 inch lockbolt into breakout carrier frame and threshold.

08 42 29-18

Page 19:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

13. Basic Sensor System: 24 VDC, class ll circuit adjusted and installed in compliance with ANSI A156.10. System shall include the following:a. Activation Sensors: Microwave or active infrared sensor shall be header-

mounted each side of door unit for detection of traffic from each direction.b. Threshold Presence Sensors:

1) Header mounted sensors shall provide active infrared presence detection on each side of the door unit and shall remain active throughout the entire door opening and closing cycle.

2) Hold-open beams: Two pulsed infrared photoelectric beams to be mounted in vertical rails of sidelite or in jambs. Sender/receiver arrangement parallels door opening.

2.3 AUTOMATIC HURRICANE RATED SLIDING DOORS

A. Hurricane Rated Sliding Door System with Electric Linear or Belt Drive Operator: Horton Automatics Hurricane Rated Series with operator, header with roller track, carrier assemblies, framing, sliding door panel(s), sidelite(s), activation, safety devices and accessories required for complete installation.1. Model:

a. ProfilerStorm Type 110: Sliding (O-SX-SX-O) w/ fixed push bar and top/bottom flush bolts and 3 point lock plus or minus 55 psf Maximum size 192 inches W by 104 inches H. Miami-Dade NOA 14-060204 Non-Impact.

b. ProfilerStorm Type 310: Sliding (SO-SX-SX-SO) w/ fixed push bar and top/bottom flush bolts and 3 point lock plus or minus 55 psf Maximum size 192 inches W by 104 inches H. Miami-Dade NOA 14-060204 Non-Impact.

c. ProfilerStorm Type 310: Sliding (SO-SX-SX-SO) w/ panic device plus or minus 45 psf Maximum size 168 inches W by 96 inches H. Miami-Dade NOA 14-060204 Non-Impact.

d. HD-Storm Type 310: Bi-parting (SO-SX-SX-SO) Rated plus or minus 85 psf Large and Small Missile Impact resistant with laminated glass Max Size 14 feet by 7 feet 8 inches. 3 point lock. Miami-Dade NOA 14-040804 Large and Small Missile Impact.

e. HD-Storm Type 310: Single Slide (SO-SX) Rated plus or minus 70 psf Large and Small Missile Impact resistant with laminated glass Max Size 9 feet by 7 feet 8 inches. 3 point lock Miami-Dade NOA 14-040804 Large and Small Missile Impact.

2. Mounting Type:a. Perimeter mounted within rough opening.

3. Operator: Profiler Series 2000 Linear Drive. Operator shall be mounted and concealed within the header.a. Profiler Series 2000 Linear Drive. Operator shall be mounted and concealed

within the header. Motor 1/8 HP DC permanent magnet working with a threadless, induction hardened stainless steel 1/2 inch (13 mm) diameter linear drive shaft. Maximum current draw shall not exceed 3.15 amps. A linear travel block describes a helical path along the rotating shaft utilizing six aircraft quality ball bearings acting as an integral clutch. Linear drive shaft is self lubricating.

b. Profiler Series 2000B Elite Belt Drive electric operating mechanism. Operating force shall be accomplished through a 1/8 HP DC permanent magnet motor with worm gear transmission and 1800 RPM working with drive belt, attached door hangers, and idler pulley. Drive belt to be steel reinforced nylon, 1/2 inch (13 mm) wide. Idler pulley to be reinforced, metallic material.

c. Master Control: 16 bit microprocessor controller with dual on-board seven-segment alphanumeric diagnostic display and position encoder. Encoder shall monitor revolutions of the operator shaft and send signals to microprocessor controller to define door position and speed. Control shall have minimum of 28 programmable parameters including the following functions as required by

08 42 29-19

Page 20:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

ANSI A156.10:1) Adjustable opening and closing speeds.2) Adjustable back-check and latching.3) Adjustable braking.4) Adjustable hold-open time between 1 to 30 seconds.5) Adjustable Reversing Circuit will reopen door unit if closing path is

obstructed.6) Separate day and night modes of operation with security over-ride.

d. Finger Safety: Strike rail of sliding panel will stop short of adjacent sidelite; resulting opening is net slide.

e. On/Off Switch: When switched OFF or during electrical power failure, unit reverts to free manual operation.

4. Security and Safety Power Fail Options:a. Automatic lock: Automatically locks slide function of door when in closed

position. Additional power supply for autolock not acceptable.1) Autolock Fail Secure: If power fails the lock engages.2) Autolock Fail Safe: If power fails the lock disengages.

b. Monitored Power Fail Options (battery back-up):1) Software Selectable Power Fail Open: If power fails the door slides open.2) Software Selectable Power Fail Close: If power fails the door slides

closed.5. Profiler Header: Slim 4 inches (102 mm) deep by 6 inches (152 mm) high aluminum

construction with extruded z-profile reinforcement for dead load and lateral strength. Header shall have removable face plate.

6. Header Capacity: Header shall be capable of supporting:a. Biparting: Up to 250 lbs. (113.4 kg) per slide panel over spans up to 16 feet 0

inches (4877 mm) without intermediate supports.b. Single Slide: Up to 350 lbs. (158.7 kg) per slide panel over spans up to 9 feet 0

inches (2743 mm) without intermediate supports.7. Header Capacity: Header shall be capable of supporting:

a. Biparting: Up to 300 lbs. (136 kg) per slide panel over spans up to 16 feet 0 inches (4877 mm) without intermediate supports.

b. Single Slide: Up to 500 lbs. (227 kg) per slide panel over spans up to 9 feet 0 inches (2743 mm) without intermediate supports.

8. Carrier and Header Roller Track: Carrier assemblies support door panels with minimum four rollers per panel. Rollers are steel, high quality ball bearing wheels 1-1/4 inch (32 mm) diameter. Anti-Derailing is accomplished by a continuous aluminum extrusion full length of slide panel travel. Overhead header roller track is continuous aluminum, nylon covered, and replaceable.

9. Sliding Panel(s) and Sidelite(s): Aluminum, 1-3/4 inches (44 mm) deep with medium stile rails. Weather-stripping to be along perimeter of sliding panel(s) and swing-out sidelite(s). Concealed guides to stabilize bottom of sliding panel. Standard glazing prep to be noted on appropriate NOA drawing.

10. Breakout Panels: Slide-swing panels can swing out minimum of 90 degrees from any position of slide movement and require no more than 50 lbf. (222 N) of force applied at the lock stile to open. Slide-swing panels and swing-out sidelites shall utilize spring loaded ball detent.a. Slide-swing panels and swing-out sidelites shall have torsion spring designed to

re-close panel if pushed open in the direction of egress.b. Breakout mechanism shall provide support across full width of the door, in

normal operating mode. In breakout mode, torsion assembly shall support weight of the door to minimize drop during emergency egress.

c. Units with breakout feature are ETL listed as an exit away and are compliant with NFPA 101.

11. Jambs/Frame: Aluminum. 1-3/4 inches (44 mm) deep by 4 inches (102 mm) wide12. Threshold: Shall be aluminum

08 42 29-20

Page 21:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

a. 1/2 inch (25 mm) tall by 4 inches (102 mm) wide.b. 7 inches (178 mm) wide.

13. Hardware:a. ANSI A156.5, Grade 1, 3-Point locking for biparting doors shall include:

1) Hookbolt Lock, 5/8 inch latching into jamb or adjacent strike rail.2) Maximum Security Lock with 31/32 inch (25 mm) backset.3) Keyed Cylinder mounted on exterior side with 1-5/32 inches (29 mm)

standard size cylinder.4) Thumbturn mounted on interior side.5) 3/8 inch lockbolt into breakout carrier frame and threshold.

b. Cylinder Guard.c. Cylinder Escutcheon.d. Surface mounted Panic Exit Device for door type 310.

14. Basic Sensor System: 24 VDC, class ll circuit adjusted and installed in compliance with ANSI A156.10. System shall include the following:a. Activation Sensors: Microwave or active infrared sensor shall be header-

mounted each side of door unit for detection of traffic from each direction.b. Threshold Presence Sensors:

1) Header mounted sensors shall provide active infrared presence detection on each side of the door unit and shall remain active throughout the entire door opening and closing cycle.

2) Hold-open beams: Two pulsed infrared photoelectric beams to be mounted in vertical rails of sidelite or in jambs. Sender/receiver arrangement parallels door opening.

2.4 CLEANROOM SLIDING DOORS

A. Sliding Door System with Linear Drive Operator: Horton Automatics UltraClean Atmospheric 1 Linear Drive Automatic Door System with operator, header with roller track, carrier assemblies, framing, sliding door panel, sidelite, activation, safety devices and accessories required for complete installation.1. Model:

a. UltraClean Atmospheric I Linear Drive Automatic Door System with Linear Drive Operator. Compliant with ISO Class 3 Cleanrooms.

2. Configuration:a. Single Slide

3. Mounting Type:a. Perimeter mounted within rough opening.b. Surface mounted.

4. Door Type:a. Type 010: Sliding panel ' X' shall slide along fixed sidelite ' O' or wall ' P'.b. Type 110: Slide-swing panel ' SX' shall slide along sidelite ' O' or wall ' P'.

5. Operator: Profiler Series 2000 Linear Drive. Operator shall be mounted and concealed within the header.a. Motor: 1/8 HP DC permanent magnet working with a threadless, induction

hardened stainless steel 1/2 inch (13 mm) diameter linear drive shaft. Maximum current draw shall not exceed 3.15 amps. A linear travel block describes a helical path along the rotating shaft utilizing six aircraft quality ball bearings acting as an integral clutch. Linear drive shaft is self lubricating.

b. Master Control: 16 bit microprocessor controller with dual on-board seven-segment alphanumeric diagnostic display and position encoder. Encoder shall monitor revolutions of the operator shaft and send signals to microprocessor controller to define door position and speed. Control shall have minimum of 28 programmable parameters including the following functions as required by ANSI A156.10:1) Adjustable opening and closing speeds.

08 42 29-21

Page 22:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

2) Adjustable back-check and latching.3) Adjustable braking.4) Adjustable hold-open time between 1 to 30 seconds.5) Adjustable Reversing Circuit will reopen door unit if closing path is

obstructed.6) Separate day and night modes of operation with security over-ride.

c. Finger Safety: Strike rail of sliding panel will stop short of adjacent sidelite; resulting opening is net slide.

d. On/Off Switch: When switched OFF or during electrical power failure, unit reverts to free manual operation.

6. Profiler Header: Slim 4 inch (102 mm) deep by 6 inch (152 mm) high aluminum construction with extruded z-profile reinforcement for dead load and lateral strength. Header has removable face plate for service and adjustment of operator and controls and mounts flush to 4 inch framing jambs.a. Provide with anodized aluminum hood.b. Provide with stainless steel hood.

7. Header Capacity: Header shall be capable of supporting:a. Biparting: Up to 350 lbs. (158.7 kg) per slide panel over spans up to 9 feet 0

inches (2743 mm) without intermediate supports.8. Carrier and Header Roller Track: Carrier assemblies support door panels with

minimum four rollers per panel. Rollers are steel, high quality ball bearing wheels 1-1/4 inch (32 mm) diameter. Anti-Derailing is accomplished by a continuous aluminum extrusion full length of slide panel travel. Overhead header roller track is continuous aluminum, nylon covered, and replaceable.

9. Sliding Panel and Sidelite: Aluminum, 1-3/4 inches (44 mm) deep with narrow stile rails. An intermediate, horizontal rail (muntin bar), 2-1/4 inches (57 mm) wide, is furnished for safety and division of glass (optional on 010 units). Standard bottom rail shall be 4 inches (102 mm) tall. Sliding panels have concealed bottom guides to stabilize slide travel.a. Weather-stripping: Provide at perimeter of sliding panel(s) and swing-out

sidelite(s). Weatherstripping material is captured in extruded aluminum door panel. Surface applied self-adhesive weatherstripping not acceptable. Provide adjustable spring-loaded double astragal weather-stripping at lead edge, double mohair at interlock rails

b. Glazing prep to be for ___ glass thickness.c. Sliding Panel and Sidelite Options:

1) Medium stile construction: 3-3/4 inches (95 mm) wide vertical rails with 6-1/2 inches (165mm) tall bottom rail. Note: Medium stile construction will reduce slide opening.

2) Wide stile construction: 5 inches (127 mm) wide vertical rails with 6-1/2 inches (165mm) tall bottom rail. Note: Wide stile construction will reduce slide opening.

3) Surface applied push bar 1-1/2 inches (32 mm) wide in lieu of standard muntin bar.

4) Custom horizontal muntins from 1/2 inch (13 mm) to 10 inches (254 mm) wide.

5) Custom bottom rails up to 10 inches (254 mm) tall.10. Breakout Panels: Slide-swing panels can swing out minimum of 90 degrees from any

position of slide movement and require no more than 50 lbf. (222 N) of force applied at the lock stile to open.a. Slide-swing panels and swing-out sidelites shall have torsion spring designed to

re-close panel if pushed open in the direction of egress.b. Breakout mechanism shall provide support across full width of the door, in

normal operating mode. In breakout mode, torsion assembly shall support weight of the door to minimize drop during emergency egress.

c. Slide-swing panels shall include intermediate horizontal rail.

08 42 29-22

Page 23:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

d. Units with breakout feature are ETL listed as an exit away and are compliant with NFPA 101.

11. Jambs/Frame: Aluminum.a. 1-3/4 inches (44 mm) deep by 4 inches (102 mm) wide.

12. Hardware:a. ANSI A156.5, Grade 1, 2-Point Locking provided and installed in strike rail shall

include:1) Hookbolt Latch, 5/8 inch laminated stainless steel, latching into jamb or

adjacent strike rail.2) 3/8 inch hex-bolt into breakout carrier frame.3) Keyed 1-5/32 inches (29 mm) Cylinder mounted on exterior side with

31/32 inch (25 mm) backset4) Thumbturn mounted on interior side.

13. Activating Device: 24 VDC, class ll circuit adjusted. Switch to be located on each side of the opening and shall be one of the following:a. Touchless wall mounted switch (optional jamb mounted) using diffused

scanning technology with adjustable range up to 15 inches (381 mm). Junction box included.

b. Motion Sensor: Mounted above opening on header or wall.c. Pull Chain Switch: Momentary contact switch, ceiling mounted with available

chain length of 114 inches (2896 mm).d. Push Plate Wall Switch: Momentary contact switch, 6-1/4 inches (159 mm)

diameter stainless steel plate on standard junction box.14. Threshold Presence Sensors:

a. Header mounted sensors shall provide active infrared presence detection on each side of the door unit and shall remain active throughout the entire door opening and closing cycle.

b. Hold-open beams: Two pulsed infrared photoelectric beams to be mounted in vertical rails of sidelite or in jambs. Sender/receiver arrangement parallels door opening.

15. Interlock Controller: Multiple doors entering a clean room and/or vestibule area shall include a microprocessor based interlock control to prevent two doors from being open at the same time. Control shall keep track of the order of request from the activation switch. Design shall control up to eight doors and shall have a memory capable of remembering order of open requests

B. Cleanroom Sliding Door System with Drive Operator: Horton Automatics Automatic Cleanroom Door System with operator, header with roller track, carrier assemblies, framing, sliding door panel, sidelite, activation, safety devices and accessories required for complete installation.1. Model:

a. UltraClean Atmospheric II Automatic Door System with Linear Drive or Belt Drive Operator. Compliant with ISO Class __ Cleanrooms.

b. UltraClean Sterile Automatic Door System with Heavy Duty Belt Drive Operator. Compliant with ISO Class __ Cleanrooms.

2. Configuration:a. Single Slideb. Bi-Parting

3. Mounting Type:a. Perimeter mounted within rough opening.b. Surface mounted.

4. Door Type:a. Type 010: Sliding panel ' X' shall slide along fixed sidelite ' O' or wall ' P'.b. Type 110: Slide-swing panel ' SX' shall slide along sidelite ' O' or wall ' P'.

5. Operator: Profiler Series 2000 Linear Drive. Operator shall be mounted and concealed within the header. Motor 1/8 HP DC permanent magnet working with a threadless,

08 42 29-23

Page 24:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

induction hardened stainless steel 1/2 inch (13 mm) diameter linear drive shaft. Maximum current draw shall not exceed 3.15 amps. A linear travel block describes a helical path along the rotating shaft utilizing six aircraft quality ball bearings acting as an integral clutch. Linear drive shaft is self lubricating.

6. Operator: Profiler Series 2000B Elite Belt Drive. Operator shall be mounted and concealed within the header. Motor 1/8 HP DC permanent magnet motor with worm gear transmission and 1800 RPM working with drive belt, attached door hangers, and idler pulley. Maximum draw shall not exceed 3.15 amps. Drive belt is steel reinforced nylon, 1/2 inch (13 mm) wide. Idler pulley is reinforced, metallic material.

7. Operator: Profiler Series 20001 HD-Slide Belt Drive. Operator shall be mounted and concealed within the header. Motor 1/8 HP DC permanent magnet motor with worm gear transmission and 1800 RPM working with reinforced drive belt, attached 1/4 inch thick steel door hangers, and idler pulley. (1/4 HP motor required for door panels weighing 500 lbs). Drive belt to be steel reinforced nylon, 1 inch (25.4 mm) wide. Idler pulley to be reinforced, metallic material.a. Master Control: 16 bit microprocessor controller with dual on-board seven-

segment alphanumeric diagnostic display and position encoder. Encoder shall monitor revolutions of the operator shaft and send signals to microprocessor controller to define door position and speed. Control shall have minimum of 28 programmable parameters including the following functions as required by ANSI A156.10:1) Adjustable opening and closing speeds.2) Adjustable back-check and latching.3) Adjustable braking.4) Adjustable hold-open time between 1 to 30 seconds.5) Adjustable Reversing Circuit will reopen door unit if closing path is

obstructed.6) Separate day and night modes of operation with security over-ride.

b. Finger Safety: Strike rail of sliding panel will stop short of adjacent sidelite; resulting opening is net slide.

c. On/Off Switch: When switched OFF or during electrical power failure, unit reverts to free manual operation.

8. Security and Safety Power Fail Options:a. Automatic lock: Automatically locks slide function of door when in closed

position. Additional power supply for autolock not acceptable.1) Autolock Fail Secure: If power fails the lock engages.2) Autolock Fail Safe: If power fails the lock disengages.

b. Monitored Power Fail Options (battery back-up):1) Software Selectable Power Fail Open: If power fails the door slides open.2) Software Selectable Power Fail Close: If power fails the door slides

closed.9. Profiler Header: Slim 4 inch (102 mm) deep by 6 inch (152 mm) high aluminum

construction with extruded z-profile reinforcement for dead load and lateral strength. Header has removable face plate for service and adjustment of operator and controls and mounts flush to 4 inch framing jambs.a. Provide with anodized aluminum hood.b. Provide with stainless steel hood.

10. Header Capacity: Header shall be capable of supporting:a. Biparting: Up to 250 lbs. (113.4 kg) per slide panel over spans up to 16 feet 0

inches (4877 mm) without intermediate supports.b. Single Slide: Up to 350 lbs. (158.7 kg) per slide panel over spans up to 9 feet 0

inches (2743 mm) without intermediate supports.11. Header Capacity: Header shall be capable of supporting:

a. Biparting: Up to 300 lbs. (136 kg) per slide panel over spans up to 16 feet 0 inches (4877 mm) without intermediate supports.

b. Single Slide: Up to 500 lbs. (227 kg) per slide panel over spans up to 9 feet 0

08 42 29-24

Page 25:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

inches (2743 mm) without intermediate supports.12. Carrier and Header Roller Track: Carrier assemblies support door panels with

minimum four rollers per panel. Rollers are steel, high quality ball bearing wheels 1-1/4 inch (32 mm) diameter. Anti-Derailing is accomplished by a continuous aluminum extrusion full length of slide panel travel. Overhead header roller track is continuous aluminum, nylon covered, and replaceable.

13. Sliding Panel and Sidelite: Aluminum, 1-3/4 inches (44 mm) deep with narrow stile rails. An intermediate, horizontal rail (muntin bar), 2-1/4 inches (57 mm) wide, is furnished for safety and division of glass (optional on 010 units). Standard bottom rail shall be 4 inches (102 mm) tall. Sliding panels have concealed bottom guides to stabilize slide travel.a. Weather-stripping: Provide at perimeter of sliding panel(s) and swing-out

sidelite(s). Weatherstripping material is captured in extruded aluminum door panel. Surface applied self-adhesive weatherstripping not acceptable. Provide adjustable spring-loaded double astragal weather-stripping at lead edge, double mohair at interlock rails

b. Glazing prep to be for ___ glass thickness.c. Sliding Panel and Sidelite Options:

1) Medium stile construction: 3-3/4 inches (95 mm) wide vertical rails with 6-1/2 inches (165mm) tall bottom rail. Note: Medium stile construction will reduce slide opening.

2) Wide stile construction: 5 inches (127 mm) wide vertical rails with 6-1/2 inches (165mm) tall bottom rail. Note: Wide stile construction will reduce slide opening.

3) Surface applied push bar 1-1/2 inches (32 mm) wide in lieu of standard muntin bar.

4) Custom horizontal muntins from 1/2 inch (13 mm) to 10 inches (254 mm) wide.

5) Custom bottom rails up to 10 inches (254 mm) tall.14. Breakout Panels: Slide-swing panels can swing out minimum of 90 degrees from any

position of slide movement and require no more than 50 lbf. (222 N) of force applied at the lock stile to open.a. Slide-swing panels and swing-out sidelites shall have torsion spring designed to

re-close panel if pushed open in the direction of egress.b. Breakout mechanism shall provide support across full width of the door, in

normal operating mode. In breakout mode, torsion assembly shall support weight of the door to minimize drop during emergency egress.

c. Slide-swing panels shall include intermediate horizontal rail.d. Units with breakout feature are ETL listed as an exit away and are compliant

with NFPA 101.15. Jambs/Frame: Aluminum.

a. 1-3/4 inches (44 mm) deep by 4 inches (102 mm) wide.b. 1-3/4 inches (44 mm) deep by 4-1/2 inches (114 mm) wide.c. 1-3/4 inches (44 mm) deep by 6 inches (152 mm) wide. Maximum height: 8 feet

8 inches.d. 2 inches (51 mm) deep by 6 inches (152 mm) wide. Maximum height: 8 feet 8

inches.e. 4 inches (102 mm) square. Maximum height: 8 feet 8 inches.f. Transom of size and type indicated, mounted on header

16. Threshold: Shall be aluminuma. 1/2 inch (25 mm) tall by 4 inches (102 mm) wide.b. 7 inches (178 mm) wide.

17. Hardware:a. ANSI A156.5, Grade 1, 2-Point Locking provided and installed in strike rail shall

include:1) Hookbolt Latch, 5/8 inch laminated stainless steel, latching into jamb or

08 42 29-25

Page 26:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

adjacent strike rail.2) 3/8 inch hex-bolt into breakout carrier frame.3) Keyed 1-5/32 inches (29 mm) Cylinder mounted on exterior side with

31/32 inch (25 mm) backset4) Thumbturn mounted on interior side.

b. ANSI A156.5, Grade 1, 3-Point locking for biparting doors shall include:1) Hookbolt Lock, 5/8 inch latching into jamb or adjacent strike rail.2) Maximum Security Lock with 31/32 inch (25 mm) backset.3) Keyed Cylinder mounted on exterior side with 1-5/32 inches (29 mm)

standard size cylinder.4) Thumbturn mounted on interior side.5) 3/8 inch lockbolt into breakout carrier frame and threshold.

c. Flush Panic Exit Device recessed in 6-1/2 inches muntin bar for door types 010 and 110.

d. Surface mounted Panic Exit Device for door type 110.18. Activating Device: 24 VDC, class ll circuit adjusted. Switch to be located on each side

of the opening and shall be one of the following:a. Touchless wall mounted switch (optional jamb mounted) using diffused

scanning technology with adjustable range up to 15 inches (381 mm). Junction box included.

b. Motion Sensor: Mounted above opening on header or wall.c. Pull Chain Switch: Momentary contact switch, ceiling mounted with available

chain length of 114 inches (2896 mm).d. Push Plate Wall Switch: Momentary contact switch, 6-1/4 inches (159 mm)

diameter stainless steel plate on standard junction box.19. Threshold Presence Sensors:

a. Header mounted sensors shall provide active infrared presence detection on each side of the door unit and shall remain active throughout the entire door opening and closing cycle.

b. Hold-open beams: Two pulsed infrared photoelectric beams to be mounted in vertical rails of sidelite or in jambs. Sender/receiver arrangement parallels door opening.

20. Interlock Controller: Multiple doors entering a clean room and/or vestibule area shall include a microprocessor based interlock control to prevent two doors from being open at the same time. Control shall keep track of the order of request from the activation switch. Design shall control up to eight doors and shall have a memory capable of remembering order of open requests

2.5 MATERIALS

A. Extruded Aluminum: ASTM B221, 6063-T5 alloy and temper, anodized:1. Structural Header Sections: Minimum 3/16 inch (5 mm) thickness.2. Structural Frame Sections: Minimum 1/8 inch (3 mm) thickness.3. Structural Panel Sections: Commercial grade.

B. Sheet Aluminum: ASTM B 209, 5005 alloy, H15 or H34 temper.

C. Sheet Steel: ASTM A 924/A 924M; galvanized to minimum G90.

D. Steel Sections: ASTM A 36/A3 6M; shaped to suit mullion sections, galvanized.

E. Glass: Glass shall be in accordance with Safety Glazing standard ANSI-Z97.1.2.1. Single pane of fully tempered select glazing quality clear float glass, safety glass,

minimum 1/4 inch (6 mm) thick, conforming with requirements in Section 08 83 13 - Mirrored Glass Glazing.

2. Single pane of laminated glass, minimum 1/4 inch (6 mm) thick laminated glass.3. Insulated sealed double pane units, consisting of fully tempered select glazing quality

08 42 29-26

Page 27:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

clear float glass, safety glass, total thickness 1 inch (25 mm), conforming with requirements in Section 08 83 13 - Mirrored Glass Glazing.

F. Glazing Materials: Entrance manufacturer's standard types to suit application and conforming to requirements specified in Section 08 83 13 - Mirrored Glass Glazing.

G. Fasteners: Stainless steel or corrosion resistant steel.

2.6 FINISH

A. Aluminum Finish (for all exposed aluminum surfaces): Shall be one of the following:1. Anodized Aluminum:

a. 204-R1 Clear: Arch. Class 1 Clear Anodized Coating, AA-MI2C22A31.b. 204-R1 Clear: Arch. Class 2 Clear Anodized Coating, AA-MI2C22A31.c. 313-R1 Dark Bronze: Arch. Class 1 Anodized Coating, AA-MI2C22A44.d. 312-R1 Medium Bronze: Arch. Class 1 Anodized Coating, AA-MI2C22A44.e. 311-R1 Light Bronze: Arch. Class 1 Anodized Coating, AA-MI2C22A44.f. Champagne: Arch. Class 1 Anodized Coating, AA-MI2C22A44.g. Gold: Arch. Class 1 Anodized Coating, AA-MI2C22A44.

2. Paint Coating:a. Powder Coat: 100 percent V.O.C. free fluoropolymer resin-based.b. Wet Paint: Standard and custom colors available.c. Color:

1) As selected from manufacturer's standard range.2) Custom color as selected by the Architect.

3. Clad:a. Stainless steel #7 mirror finish.b. Stainless steel #4 brushed finish.c. Muntz metal (brass alloy): #7 mirror finish.d. Muntz metal (brass alloy): #4 brushed finish.

2.7 FABRlCATlON

A. Panel Construction:1. Corner block type with 3/16 inch steel backup plate construction, mechanically

secured with minimum of four hardened steel screws.2. Sash consists of snap-in glass stops, snap-in glazing beads and vinyl gaskets.3. Slide-swing doors provided with adjustable glass setting block to allow for adjusting of

door to meet site conditions eliminating the need for additional shims.

B. Frame Construction: Butt joints, mechanically secured with screws and formed alum. corner brackets.

C. Operator Construction: Electromechanical, modular type construction.

PART 3 EXECUTION

3.1 EXAMINATION

A. Do not begin installation until substrates have been properly prepared.

B. Verify that other trades are complete with their required work before installing the automatic swing door operating system.

C. Mounting surfaces shall be plumb, straight and secure; substrates shall be of proper dimension and material; material which door is anchored to shall be capable of supporting the automatic door system and associated loads.

08 42 29-27

Page 28:  · Web viewSECTION 08 42 29 AUTOMATIC SLIDING DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 - 2018 ARCAT, Inc. - All rights reserved

D. Verify electric power is available and has correct characteristics.

E. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

3.2 PREPARATION

A. Clean surfaces thoroughly prior to installation.

B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

3.3 INSTALLATION

A. Install in accordance with manufacturer's instructions.

B. Set all units plumb, level and secure.

C. Provide all fasteners required for installation of the automatic sliding door system.

D. Comply with AAMA 101, Appendix Dissimilar Materials by separating aluminum materials and other corrodible surfaces from sources of corrosion or electrolytic action contact points

E. For exterior applications install header and framing members in a bed of sealant or with joint filler or gaskets. Coordinate installation with wall flashings and other components of construction.

F. After repeated operation of the completed installation, inspect door operators and controls for optimum operating condition and safety.

G. Adjust door equipment for correct function and smooth operation.

H. Clean all metal surfaces promptly after installation.

I. Remove temporary protection, clean exposed surfaces.

3.4 FIELD QUALITY CONTROL

A. Manufacturers representative to verify that installation of doors and controls are in conformance to the manufacturer's recommendations.

B. Installation of doors and controls shall be inspected and certified by an AAADM Certified Inspector prior to doors being placed into operation.

C. Provide a completed AAADM inspection form signed by a certified AAADM inspector after the door system is completely installed and tested including glazing.

3.5 CLEANING AND PROTECTION

A. Protect installed products until completion of project.

B. Clean product surfaces and lubricate operating equipment for optimum condition and safety. Advise contractor of precautions required through the remainder of the construction period, to ensure that doors will be without damage or deterioration at the time of acceptance.

C. Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION

08 42 29-28