Watch Battery Replacement Guide

HowTo_2002 4/18/02 9:09 AM

Look at the bto the picturtypes, or IF IWATCH, REFE

STEP

1 Look at t�

Y O U W I L L N E E D

Tools

Case Holding Vise

Case Wrench

Watch Closing Hand Press Polishing Cloth

EWB-1 Battery Tester

Case Knife Plastic Tweezers

Small Screwdriver

Fine-pointTweezers

HowTo_2002 4/18/02 9:10 AM

Look at the back of the customer’s watch and compare it to the pictures below. If it does not match any of these types, or IF IT IS A SPECIALIZED OR WATER RESISTANT WATCH, REFER IT TO A PROFESSIONAL WATCHMAKER.

If the watch looks similar to this, follow the step-by-step instructions contained in the RED section labeled SNAP BACK.

STEP

1 Look at the back... ��

If the watch looks similar to this, follow the step-by-step instructions contained in the BLUE section labeled HATCH BACK.

If the watch looks similar to this, follow the step-by-step instructions contained in the GREEN section labeled SCREW BACK.

SNA

P B

AC

K

1

HowTo_2002 4/18/02 9:10 AM

SNA

P B

AC

K Place watch in the case holding viseClamp the watch in the case holding vise byopening the two halves of the block, placing thewatch in the middle and gently release or tightenthe two halves so that they hold the watch firmly.

If the watch band does not unbuckle or unclasp,separate the band by pressing down with a pointed tool to removethe spring loaded pin that connects the band to the clasp or watch.

Most case backs are snapped on andcan be removed by inserting a bladeinto the appropriate notch of the caseor case back and twisting the handleof the tool to pop off the back.

When no groove is provided, be surea sharp knife is inserted into thenarrow slot between the back andthe case. Once the knife is firnly inthe groove, a slight twist of the knifehandle will pop off the back.

Twist the tool tosnap off back.

Tool needed:Case knife

IMPORTANT: Beforeremoving battery(s),be sure to note whichside is up. You willhave to put the newEnergizer® battery inexactly the same way.In some watches, thebattery is held in bysmall metal clips. If so, carefully followthe directions to theright for removing thevarious types of clips.Use plastic tweezersto remove battery(s).

SPRING CLIP:Lift up one end of the metalclip with the fine-pointtweezers. It will come out.Then remove the battery.

SCREW-ON CLIP:Remove the screws with the small screwdriver. BECAREFUL NOT TO LOSE THEM!CAUTION: CLIP MAY SPRINGOUT. MAINTAIN PRESSURE ORSCREW MAY BE EJECTED.

Tools needed: Fine-PointTweezers, SmallScrewdriver, PlasticTweezers

PERMANENT CLIP:Lift the outside edge of the batteryout of its compartment with thesmall screwdriver.

See the battery tester for operating instructions. IMPORTANT: If the watch hastwo batteries and only one tests “replace”, replace both batteries. If bothbatteries test “good”, there is something wrong with the watch. Refer it to aprofessional watchmaker.

2

2S T E P

Remove the back3S T E P

Remove the battery4S T E P

Test the batteries5S T E P

Tools needed: EWB-1 Battery Tester

HowTo_2002 4/18/02 9:10 AM

SN

AP

BA

CK

HA

TCH

BA

CK

Read the number on the old battery and replace with the same or correspondingEnergizer® Watch Battery. Refer to the current Energizer® Watch/Electronic BatteryReplacement Guide or the Energizer® battery size checker to find the correctEnergizer® battery type number.

Check the battery compartment for dirt and remove it. If you find corrosion, refer watch to aprofessional watchmaker.

IMPORTANT: Be sure to testthe new battery beforeinstalling. For tester setting,fo l low manufacturer ’sinstructions. Use plastictweezers to install the newEnergizer® battery(s) with thesame side up as the one(s)you replaced. Remember,the watch won’t work if thebattery(s) are put in wrong.

IMPORTANT: If there is a rubber sealing gasket in the back of the watch,make sure it is lined up properly before closing back. Snap a metaladapter that is slightly smaller than the watch back into the upper jawof the press. Place the support plate into the bottom of the press and fita plastic ring adapter large enough to hold the watch on the supportplate. Place the watch face down into the plastic ring adapter and pressgently on handle until watch back snaps into place.

Reset the watch and make sure it is working. Inanalog watches, if there is no second hand,observe the minute hand through a magnifyingglass until you see movement.

SPRING CLIP:Place one end of spring clip in place and firmly pushthe other end into its slot.Make sure spring clip is in theslot to avoid bent spring clips.

SCREW-ON CLIP: Place the clip over the new Energizer® battery. Holdthe screw with the fine point tweezers to start it in thehole. Tighten the screw.

Tools needed: Small ScrewdriverFine Point TweezersPlastic Tweezers

Tools needed: Watch ClosingHand Press

3

Locate replacement battery6S T E P

Clean the battery compartment7S T E P

Install the new Energizer® battery8S T E P

Close the watch9S T E P

Clean the watch10S T E P

Reset the watch11S T E P

CrossReferenceGuide

34

1011

98

7

Gently wipe the watch to remove anyfingerprints or smudges.

Tool needed: Polishing cloth

HowTo_2002 4/18/02 9:10 AM

HA

TCH

BA

CK

Tool needed: Plastic Tweezers

Place watch in the case holding viseClamp the watch in the case holding vise byopening the two halves of the block, place thewatch in the middle and gently release or tightenthe two halves so that they hold the watch firmly.

If the watch band does not unbuckle or unclasp, separate the band bypressing down with a pointed tool to remove the spring loaded pin thatconnects the band to the clasp or watch.

Unscrew the hatch counter-clockwise byturning a coin in the slot. Once the hatch isloosened, finish unscrewing and remove withfingers. BE CAREFUL NOT TO LET THE BATTERYFALL OUT YET.

IMPORTANT: Before removing battery(s), be sure to note whichside is up. You will have to put the new Energizer® battery inexactly the same way. To remove the battery, simply turn thewatch over and it should fall out. If the battery is stuck, gentlypry it out. Use plastic tweezers to remove battery(s).

See the battery tester for operating instructions. IMPORTANT: If the watch has two batteries and only one tests “replace”,replace both batteries. If both batteries test “good”, there is somethingwrong with the watch. Refer it to a professional watchmaker.

4

2S T E P

Remove the hatch3S T E P



Tool needed: EWB-1 Battery Tester

HowTo_2002 4/18/02 9:10 AM

HA

TC

H B

AC

K SCR

EW B

AC

K

Tool needed: Plastic Tweezers



Start screwing in the hatch with your fingers,then tighten with a coin.


IMPORTANT: Be sure to test the new battery before installing. Fortester setting, follow manufacturer’s instructions. Use plastictweezers to install the new Energizer® battery(s) with the sameside up as the one(s) you replaced. Remember, the watch won’twork if the battery(s) are put in wrong.

5




Close the hatch9S T E P



CrossReferenceGuide

34

1011

98

7



HowTo_2002 4/18/02 9:10 AM

SCR

EW B

AC

K

Place watch in the case holding viseClamp the watch in the case holding vise byopening the two halves of the block, placing thewatch in the middle and gently release or tightenthe two halves so that they hold the watch firmly.

If the watch band does not unbuckle or unclasp,separate the band by pressing down with a pointed tool to removethe spring loaded pin that connects the band to the clasp or watch.

IMPORTANT: Beforeremoving battery(s),be sure to note whichside is up. You willhave to put the newEnergizer® battery inexactly the same way.In some watches, thebattery is held in bysmall metal clips. If so, carefully followthe directions to theright for removing thevarious types of clips.Use plastic tweezersto remove battery(s).

SPRING CLIP:Lift up one end of the metalclip with the fine-pointtweezers. It will come out.Then remove the battery.

SCREW-ON CLIP:Remove the screws with the small screwdriver. BECAREFUL NOT TO LOSE THEM!CAUTION: CLIP MAY SPRINGOUT. MAINTAIN PRESSURE ORSCREW MAY BE EJECTED.

Tools needed: Fine-PointTweezers, SmallScrewdriver, PlasticTweezers

PERMANENT CLIP:Lift the outside edge of the batteryout of its compartment with thesmall screwdriver.

See the battery tester for operating instructions. IMPORTANT: If the watch hastwo batteries and only one tests “replace”, replace both batteries. If bothbatteries test “good”, there is something wrong with the watch. Refer it to aprofessional watchmaker.

6

2S T E P



Tools needed: EWB-1 Battery Tester

Place the Case Wrench metal tips in the watch back notches.

Turn counter-clockwise to remove watch back

Tool needed: Case Wrench

Locate the wrench slots on the back of the watch.

Remove the back3S T E P

HowTo_2002 4/18/02 9:10 AM

SC

RE

W B

AC

K

CR

OSS R

EFEREN

CE



IMPORTANT: Be sure to testthe new battery beforeinstalling. For tester setting,fo l low manufacturer ’sinstructions. Use plastictweezers to install the newEnergizer® battery(s) withthe same side up as theone(s) you replaced.Remember, the watch won’twork if the battery(s) areput in wrong.

IMPORTANT: If there is a rubber sealing gasket in theback of the watch, make sure it is lined up properlybefore closing back. Start the back by turning itclockwise with your fingers, then tighten it with theCase Wrench.


SPRING CLIP:Place one end of spring clip in place and firmly pushthe other end into its slot.Make sure spring clip is in theslot to avoid bent spring clips.

SCREW-ON CLIP: Place the clip over the new Energizer® battery. Holdthe screw with the fine point tweezers to start it in thehole. Tighten the screw.

Tools needed: Small ScrewdriverFine Point TweezersPlastic Tweezers




Close the watch9S T E P



CrossReferenceGuide

34

1011

98

7

Tool needed: Case knife



7

HowTo_2002 4/18/02 9:10 AM

301 Silver Low SR43SW303 Silver Low SR44SW309 Silver Low SR754SW311 Silver Low SR910SW314 Silver High SR716W315 Silver Low SR716SW317 Silver Low SR516SW319 Silver Low SR527SW321 Silver Low SR616SW329 Silver Low SR731SW333 Silver Low SR610SW335 Silver Low SR512SW337 Silver Low SR416SW339 Silver Low SR614SW341 Silver Low —344 Silver Low SR1136SW346 Silver Low SR712SW350 Silver High —357 Silver High SR44W361 Silver High SR721W362 Silver Low SR721SW364 Silver Low SR621SW365 Silver High SR1116W366 Silver Low SR1116SW370 Silver High SR920W371 Silver Low SR920SW373 Silver Low SR916SW376 Silver High SR626W377 Silver High SR626W379 Silver Low SR521SW

8

Energizer® Battery Chemical Test Load ReplacementBattery No.* System Drain Number

WATCH BATTERY CROSS REFERENCE CHART

CR

OSS

REF

EREN

CE

HowTo_2002 4/18/02 9:10 AM

9

381 Silver Low SR1120SW384 Silver Low SR41SW386 Silver High SR43W387S Silver Low —389 Silver High SR1130W390 Silver Low SR1130SW391 Silver High SR1120W392 Silver High SR41W393 Silver High SR754W394 Silver Low SR936SW395 Silver Low SR927SW396 Silver High SR726W397 Silver Low SR726SW399 Silver High SR927SWECR1025 Lithium Low CR1025ECR1216 Lithium Low CR1216ECR1220 Lithium Low CR1220ECR1225 Lithium Low CR1225ECR1616 Lithium Low CR1616ECR1620 Lithium Low CR1620ECR1632 Lithium Low CR1632ECR2012 Lithium Low CR2012ECR2016 Lithium Low CR2016ECR2025 Lithium Low CR2025ECR2032 Lithium Low CR2032ECR2320 Lithium Low CR2320ECR2430 Lithium Low CR2430ECR2450 Lithium Low CR2450EPX76 Silver High SR44

*For additional numbers, refer to the Energizer® Wath Battery Replacement Guide or Energizer® Battery Size Checker

Energizer® Battery Chemical Test Load ReplacementBattery No.* System Drain Number

WATCH BATTERY CROSS REFERENCE CHART

HowTo_2002 4/18/02 9:10 AM

Watch Battery Replacement Guide

Documents

Transcript of Watch Battery Replacement Guide