Washer Specifications

ULP-302

ULP-402

Lath-Lock

PBH™ Washer - 2” DiameterAlso With Screws for Wood/Lite Metal, Steel & Masonry

DP300™ Washer - 1 3/4” DiameterAlso With Screws for Wood/Lite Metal, Steel & Masonry

DP400™ Washer - 1 3/4” DiameterWith Pre-Spot Stem

DP500™ Tab Washer - 1 1/4” DiameterG-90 Chromium Plated Steel

Demand Products, Inc.

E q u i v a l e n c e s a n d A p p r o v a l s

• EIFS Manufacturers ApprovalsUpon Request

• 3rd Party Windload TestingUpon Request

• All Fasteners Meet or Exceed EIFSManufacturer Requirements —ASTM E330 and ASTM B117

8"

These spacing patterns aregeneral guidelines for mechan-ical installation of EPS to differ-ent substrates when used inconjunction with a typical EIFSsystem or similar systems.Construction projects vary andyours may be different fromthese fastener suggestions.Please consult your EIFS man-ufacturer when using Demandfasteners along with adhe-sives. For additional informa-tion call Demand ProductsTechnical Services at 1-800-325-7540

12" 12" 12"

6"

6"

6"6"

48"

24"

12"

Wood,Plywood,Metal Siding,Masonry andConcrete

24"

16" 16"

4"

4"

8"8"

48"

24"

8"

8"

6"

6 "

12"

8" 8" 8" 8" 8" StructuralSubstratesSuch asWoodSheathing,Concrete,Masonry &Metal Siding

Testing was performed by Underwriters Laboratories per ASTM E330 and E331. Procedure B

Non-StructuralSheathingssuch as OSB,Gypsum,Dens-GlassGold

48"

4"

24"

4"

4 "

8"

8"

4" 10" 10" 10" 10"

48"

StructuralSubstratesSuch asWoodSheathing,Concrete,Masonry &Metal Siding

Screw Pullout Performance Data

Fastener Depth of Embedment in Solid Material (inches)Diameter 1" 11⁄4" 11⁄2" 13⁄4"

3⁄16" 341 581 863 1059Test #CH3932/Pittsburgh Testing Laboratories

Fastener Depth of Embedment in Solid Material (inches)Diameter 1" 11⁄4" 11⁄2" 13⁄4"

3⁄16" *209 *357 *468 *547Test #CH3748/Pittsburgh Testing Laboratories

Nominal Gauge 26 24 22 20

Pullout Strength 120 183 248 296

Nominal Gauge 18 16 14 12

Pullout Strength 471 679 847 1225

MASONRY

STEEL

Coating: CLIMACOAT™Corrosion Resistance: Kestemich Results (Din 50018, 2.OL ) • 20 cycles - 10% or less red rust. SaltSpray Results (ASTM B117) • 500 hours - 10% or less red rust for wood,lite-metal and steel fasteners.

Solid Concrete

Hollow Block

Coating: CLIMASEAL™ for masonry/concrete fasteners onlyCorrosion Resistance: Kestemich Results (Din50018, 2.OL) • 30 cycles - 10% or less red rust.Salt Spray Results (ASTM B117) • 720 Hours -10% or less red rust.

Coating: CLIMASEAL™ for masonry/concretefasteners onlyCorrosion Resistance: Kestemich Results (Din50018, 2.OL) • 30 cycles - 10% or less red rust.Salt Spray Results (ASTM B117) • 720 Hours -10% or less red rust.

*Note 1: Masonry must be pre-drilled 1⁄2" deeper than fastener penetration.*Note 2: Hardness of masonry varies and the standard drill bit may not always drill

the adequate hole. Please consult Demand Products for assistance in prop-er drill bit diameter.

(1⁄4" Minimum Through Penetration) (1⁄4" Minimum Through Penetration)

Please Note: The pullout values listed are the ultimate averages achieved under laboratory conditions.An appropriate safety margin factor should beapplied to these values to achieve adesign value.

CONCRETE

(conforms to ASTM C-548 & C-1002) (conforms to ASTM C-954 & C-548)

W00D

METAL

LT.

A

B

C

D

Windload Specs for PB & PBH Washers

Wind-Devil® 2

All of Our Screws Meet or Exceed ASTM B117

Non-Approved Fasteners & Uncoated Screws Can Cost

You, Your Reputation

1.0 Lb. EPS Pattern A Pattern B1" 83 85

11/2" 105 104

Wind Load Capacity(Average Ultimate PSF, Negative Pressure

2” Diameter •

•

• •

•Large Keyholes forStrong Mechanical Bond

Popouts

Finger Closures

Exceeds Miami/Dade Wind-Load Pull-Off Minimum of 90 PSF

Eliminates Thermal Bridging

White — No Color Bleedthru

For Polymer Based EIFS

Designed for ALLEPS Thicknesses

For PolymerBased Systems

EIFS MANUFACTURER APPROVED

PBH PB

Available Pre-Assembled for Wood/Lite Metal, Steel & Masonry

Demand Products Assembled Fasteners

3. Install PBH™ or PB™ in a manner so the fasteneris flush with the surface of the InsulationBoard. Do not exceed 1.6 mm (1/16”) belowthe surface.

4. Rasp the surface of the Insulation Boardwith a DuraVac™ DuraRasp™ to remove any irregularities.

1. Insulation Board shall be attached to theapproved substrate horizontally with vertical joints staggered and butted tightly.

2. PBH™ or PB™ by Demand Products, Inc. aredesigned to be used with EIFS ManufacturersPB EIFS. Screws shall meet ASTM B117.

Cone DesignPrevents Popouts

CREATING SOLUTIONS FOR THE FOAM INDUSTRY

1055 Nine North Dr. | Alpharetta, GA 30004 USA TEL. 770.772.7448 | FAX. 1.770.772.4618 | TEL. 800.325.7540

www.demandproducts.com | info@demandproducts.com