WARNING! - Price Industries...B) TO ENSURE YOUR HEPA FILTER IS SEATED PROPERLY, THE HEPA FILTER...
2
HE / HEPA / ULPA FILTER ROOM-SIDE REMOVABLE FILTER (RSR) INSTALLATION INSTRUCTIONS priceindustries.com | LCESM1-003 | V100 A) CAREFULLY CUT OPEN BOX AND REMOVE INNER FILTER PACKAGING. AVOID APPLYING PRESSURE TO FILTER WHILE HANDLING PACKAGING. C) CUT PLASTIC BAG AND REMOVE WITH CARE. B) PLACE UNIT ON FLAT SURFACE OR TABLE AND OPEN INNER PACKAGING. D) TO HANDLE THE FILTER, GRASP IT BY THE FRAME ONLY. WARNING! Damage to filters occurring during or after installation and leak qualification testing failures. The filters supplied by Price have been 100% tested and certified by the manufacturer to be free of defects and leaks. Price cannot accept responsibility for damage that occurs after shipment, whether through transit, handling or installation, and will not replace filters under our standard warranty. EXTREME CAUTION SHOULD BE TAKEN TO AVOID CONTACT WITH MEDIA Filters should be installed in teams of 2 or 3 installers, with 1 or 2 installers on the floor unpacking the filters, as they are needed. The filters should then be handed to the filter installers, who work on scaffolding or ladders (as applicable). TOUCHING FILTER MEDIA WILL RESULT IN DAMAGE TO THE MEDIA THAT WILL AFFECT THE PERFORMANCE OF THE FILTER STEP 1: UNPACK FILTER
Transcript of WARNING! - Price Industries...B) TO ENSURE YOUR HEPA FILTER IS SEATED PROPERLY, THE HEPA FILTER...
HE / HEPA / ULPA FILTERROOM-SIDE REMOVABLE FILTER (RSR) INSTALLATION INSTRUCTIONS
priceindustries.com | LCESM1-003 | V100
A) CAREFULLY CUT OPEN BOX AND REMOVE INNER FILTER PACKAGING. AVOID APPLYING PRESSURE TO FILTER WHILE HANDLING PACKAGING.
C) CUT PLASTIC BAG AND REMOVE WITH CARE.
B) PLACE UNIT ON FLAT SURFACE OR TABLE AND OPEN INNER PACKAGING.
D) TO HANDLE THE FILTER, GRASP IT BY THE FRAME ONLY.
WARNING!
Damage to filters occurring during or after installation and leak qualification testing failures. The filters supplied by Price have been 100% tested and certified by the manufacturer to be free of defects and leaks. Price cannot accept responsibility for damage that occurs after shipment, whether through transit, handling or installation, and will not replace filters under our standard warranty.
EXTREME CAUTION SHOULD BE TAKEN TO AVOID CONTACT WITH MEDIA
Filters should be installed in teams of 2 or 3 installers, with 1 or 2 installers on the floor unpacking the filters, as they are needed. The filters should then be handed to the filter installers, who work on scaffolding or ladders (as applicable).
TOUCHING FILTER MEDIA WILL RESULT IN DAMAGE TO THE MEDIA THAT WILL AFFECT THE PERFORMANCE OF THE FILTER
STEP 1: UNPACK FILTER
HE / HEPA / ULPA FILTERROOM-SIDE REMOVABLE FILTER (RSR) INSTALLATION INSTRUCTIONS
priceindustries.com | LCESM1-003 | V100
ALL METRIC DIMENSIONS ( ) ARE SOFT CONVERTED. IMPERIAL DIMENSIONS ARE CONVERTED TO METRIC AND ROUNDED TO THE NEAREST MILLIMETER.
0
LFDCLAMINAR FLOW DIFFUSER
FILTERED271187
PROJECT:
ENGINEER:
CUSTOMER:
SUBMITTAL DATE: SPEC. SYMBOL:
Submittal SheetLFDC FILTERED LAMINAR FLOW DIFFUSER
SEPT 2019
OF REVSHEET 1 1© Copyright PRICE INDUSTRIES 2012
Solid
Ed
ge
LFDC
Surface Mount Detail T-Bar Mount Detail
KNIFE EDGE GELSEAL DETAIL
A) LOOSEN CAM LOCKS. B) NOTE LOCATION OF FILTER ALIGNMENT GUIDE (MINIMUM ONE PER SIDE, DEPENDENT ON SIZE).
STEP 2: PREPARE FILTER FOR INSTALLATION
A) USING TWO PEOPLE AND BEING CAREFUL NOT TO CONTACT FILTER MEDIA RAISE THE FILTER INTO PLACE.
B) ENSURE KNIFE EDGE OF PLENUM SEATS INTO GEL CHANNEL. USE GUIDES TO ASSIST WITH PROPER KNIFE EDGE ALIGNMENT.
STEP 3: PLACING THE FILTER
STEP 4: INSTALLING THE FILTER
A) SECURE FILTER INTO PLACE USING FOUR CAM LOCKS. TIGHTEN UNTIL NO FURTHER ROTATIONS CAN BE MADE.
B) TO ENSURE YOUR HEPA FILTER IS SEATED PROPERLY, THE HEPA FILTER OUTER FRAME MUST BE IN CONTACT WITH THE HORIZONTAL FRAME OF THE KNIFE EDGE EXTRUSION. NOTE THAT DIFFUSER KNIFE EDGE CANNOT BOTTOM OUT IN HEPA FILTER GEL SEAL.
FILTER MEDIA
GEL SEAL
CONTACT POINT
CAM LOCK
HEPA FILTER OUTER FRAME
KNIFE EDGE
FOR ASSISTANCE, PLEASE CONTACT THE PRICE APPLICATIONS ENGINEERING TEAM BY PHONE AT (204) 654-5613 OPTION 5 OR BY EMAIL AT [email protected]
To reorder new filters please contact your local Price Sales Representative at
www.priceindustries.com/criticalenvironments/contact
