Wanne Mouthpiece Refacing Tools
description
Transcript of Wanne Mouthpiece Refacing Tools
-
Recommended Mouthpiece Refacing Tools Refacing Tools (MUST HAVE) Brand Length Width/Depth Description Extra Narrow Pillar File Coarse
Grobet 4" 5/32" by 5/64" Cut #00. Used to form the primary shape of the
baffle and window. Can be purchased at
www.mscdirect.com.
Extra Narrow Pillar File Fine
Grobet 4" 5/32" by 5/64" Cut No. 2. Used to finish the shape of baffles and
the window. Can be purchased at
www.mscdirect.com.
Hand File Coarse
Any 10" 1" by 1/4" Cut No. 00. Used to create large shape changes
on the body and outer side-rails of the
mouthpiece. Any brand like this will work. Can
be purchased at www.mscdirect.com.
Hand File Fine
Any 6" 3/4" by 5/32" Cut No. 3. Used to finish shaping the body, tip,
and outer side-rails of the mouthpiece. Can be
purchased at www.mscdirect.com.
Sanding Sticks
MSCDirect 6 These pencil-like sticks have spring-loaded
tension, holding the sanding belts in place. This
also allows for belt rotating (to use the full belt)
and changing. The tapered end permits easy
access for minute details. Can be purchased at
www.mscdirect.com.
Sanding Stick Belts
MSCDirect
6 120
240
320
400
Sanding Belts for above Sanding Sticks. 120 Grit
does primary shaping of the floor, inner side rails,
and baffle. 240 is an intermediary grit to do finer
shaping. 320 is used to finish shaping the floor,
inner side rails and creates a nicely shaped baffle.
400 grit is used to get a fine finish. All three grits
are used in succession. Can be purchased at
www.mscdirect.com.
Tip Opening Guage
Theo Wanne Necessary to measure the tip opening on all
saxophone and clarinet mouthpieces. Purchase
from www.theowanne.com or
www.musicmedic.com
-
Feeler Gauge Set
Theo Wanne US
or
Metric
Necessary with a glass gauge to measure the
facing on mouthpieces. Purchase from
www.theowanne.com or www.musicmedic.com.
I recommend getting the US Traditional set as it is
the most commonly used version.
Glass Gauge
Theo Wanne Traditional
Or
Actual mm
Necessary with a feeler gauge setbto measure the
facing on mouthpieces. Purchase from
www.theowanne.com or www.musicmedic.com.
I recommend getting the Traditional set as it is
the most commonly used version.
Imperial Sand Paper
Grobet 8
by
11
180
220
320
400
600
1000
Sandpaper for flattening the table and making the
facing curve. Use on the granite plate below.
180 and 220 for fast cutting. 320 and 400 are for
general use. 600 and 1000 are for final smooth
finishes. 400 is the most useful of all grits and
can be used for most work, as it cuts well and
leaves an adequate final finish. Can be purchased
at www.mscdirect.com.
3/8 Glass or Granite Surface Plate
Shars www.shars.com
12 x 9 x 1 thick A 3/8 thick piece of glass may also be used, as it
is lighter and more portable. A 5 x 10 piece of
glass can be purchased at www.musicmedic.com
8 by 11 is ideal as it fits the sandpaper
perfectly. Note: Never use glass thinner than
3/8 as it bends.
Granite Plate is the very best as it is very stable,
however, this is for shop use only as it is not
portable. www.shars.com has affordable
versions.
-
Rotary Hand-piece Tools (OPTIONAL) Brand Description Quick Change Rotary Handpiece
Any Motor and narrow handpiece with quick change lever for use 3/32" (2.4 mm) shanks
arbors. Buy from dental tool supply shops. Standard electric rotary handpieces
work fine too, as long as they take 3/32 shank tools.
Rotary Hand Tool Wheel Arbor
Any 3/32 shank with 1/16 arbor hole Nickel Plated Steel
3/32 shank with 1/16 arbor hole Stainless Steel
Miniature Muslin Buff
Any Use to fine polish the baffles on mouthpieces. 16 Ply with two rows of stitching. 1
Diameter. Fits abrasive wheel arbor.
Buffing Compound (Rouge)
Any Deep Red Rouge for a shiny final color on any material
Brown Tripoli for fast polishing
Black For hard rubber and plastic mouthpieces
White Diamond For Brass and Copper mouthpieces
Green for use on chrome and stainless steel (Berg Larsen, etc.)
Ball Head Burs
Fox Ball Head Burs with 3/32 shank. I recommend Fox brand, as they fit most hand-
pieces well. Use to round out the inner side-walls and make the chamber bigger.
Sizes from 1mm to 10mm are useful. These can be found on www.ebay.com