·Wall Mount Type WK ·Room Mount Type · 2020. 6. 11. · The MODEL 096 x-ray system will operate...
Transcript of ·Wall Mount Type WK ·Room Mount Type · 2020. 6. 11. · The MODEL 096 x-ray system will operate...
DENTAL X-RAY
INSTALLATIONINSTRUCTIONS (for USA & Canada)
MODEL 096
REV.4
·Wall Mount Type ....................WK·Room Mount Type ..................RK
- -
INDEX PAGE
SECTION ONE : TECHNICAL DATA [1]ELECTRICALANDRADIATIONDATA......................................................... 3 [2]PHYSICALDIMENSIONS............................................................................... 4 [3]TUBEHEADTHERMALCHARACTERISTICS............................................ 5
SECTION TWO : PRE-INSTALLATION INSTRUCTIONS [1]SUPPORTREQUIREMENTS........................................................................... 6 [2]ELECTRICALREQUIREMENTS.................................................................... 6 [3]LOCATIONOFCOMPONENTS...................................................................... 7
SECTION THREE : INSTALLATION INSTRUCTIONS [1]INSTALLATIONREQUIREMENTS................................................................ 8 [2]UNPACKING..................................................................................................... 8 [3]ARMASSEMBLYINSTALLATION................................................................. 9 [4]HEADASSEMBLYINSTALLATION............................................................ 12 [5]CONTROLBOXINSTALLATION................................................................. 12
SECTION FOUR : POST INSTALLATION INSPECTION [1]ARMASSEMBLY............................................................................................ 14 [2]BALANCEARMASSEMBLY........................................................................ 15 [3]HEADPOSITIONING..................................................................................... 15
SECTION FIVE : CONTROL IDENTIFICATION AND OPERATION [1]CONTROLIDENTIFICATION....................................................................... 16 [2]FUNCTIONOFCONTROLS.......................................................................... 16 [3]OPERATINGPROCEDURES......................................................................... 18 [4]ERRORCODES............................................................................................... 19
SECTION SIX : POST INSTALLATION CONFIRMATION [1]CONFIRMATIONOFPOWERSUPPLYVOLTAGE..................................... 20 [2]CONFIRMATIONOFTUBECURRENT....................................................... 20 [3]CONFIRMATIONOFEXPOSUREWARNINGLAMP&BUZZER............ 20 [4]CONFIRMATIONOFLINEVOLTAGEREGULATION.............................. 20
SECTION SEVEN : INITIAL SETTING [1]FILMSPEED.................................................................................................... 21 [2]PRIORITYOFSELECTIONS......................................................................... 23 [3]ELECTRONICCHIMEON/OFF.................................................................... 23
APPENDIX ONE : CIRCUIT DIAGRAM........................................................... 23
APPENDIX TWO : PARTS IDENTIFICATION [1],[2]ARMANDHEAD/CONTROLBOXASSEMBLY................................ 24 [3]SLIDINGSECTION/ARMANDHEADASSEMBLYOFRKTYPE.......... 26
APPENDIX THREE : CERTIFICATION............................................................ 28
CAUTIONThismanualprovidesinformationandinstructionsfortheinstallation,assemblycalibrationand certification procedures for BELMONT BELRAY MODEL 096dentalx-ray.Theinstructionscontainedinthisbookshouldbethoroughlyreadandunderstoodbeforeattempting to install the X-ray unit. After the installation is complete, file this manual andreferbacktoitwhenperformingperiodicmaintenance.
- -
SECTIONONE:TECHNICALDATA
[1] ELECTRICAL AND RADIATION DATA
1.Focalpointmeasurement.............................................. 0.8mmx0.8mm2.Ratedpeaktubepotential.............................................. 70kVp3.Ratedtubecurrent......................................................... 10mA4.Maximumratedpeaktubepotential............................. 70kVp5.Ratedlinevoltage......................................................... 120VAC6.Linevoltagerange......................................................... 108VAC~132VAC7.Rangeoflinevoltageregulation................................... 2~5%8.Ratedlinecurrent.......................................................... 10.8Aat70kVp,10mA9.Maximumlinecurrent................................................... 11.9Aat70kVp,10mA10.Exposuretime............................................................. 0.02~3sec. (ONandOFFarezerocrossed.)11.Timeraccuracy............................................................ ±1pulse(1/60sec.)12. Inherent filtration........................................................ 1.3mmAlEquivalent13. Added filtration........................................................... 0.8mmAl14. Minimum filtration permanently in useful beam........ 2.1mmAlEquivalentat70kVp15.Nominalroentgenoutputa.Distalendofregularcone........................................... 8.2mGy/sec.+30%,-40%b.Distalendoflongcone............................................... 3.7mGy/sec.+30%,-40%(Dataobtainedbydirectmeasurementintheusefulbeam)16.Sourcetoskindistancea.Regularcone................................................................ 204mmb.Longcone.................................................................... 305mm17.Leakagetechniquefactor............................................ 70kVp/0.16mA 0.16mAismaximumratedcontinuouscurrent for10mAwithadutycycle1:6018.Dutycycle................................................................... 1:60(0.5sec.exposurewith30sec.interval)19.Maximumdeviationoftubepotentialandtubecurrent Pulse TubePotential TubeCurrent +8 1st,2nd&3rd 70kVp 10±2mA -11
+7 4th&Up 70kVp 10±1mA -1020.Measurementbaseoftechniquefactorsa.peaktubepotential...................................................... Peaktubepotentialofconductinghalfcycleb.tubecurrent................................................................. Averageoftubecurrentduringonecycleof linefrequencyc.exposuretime.............................................................. Impulsesofpowerlinefrequency21.Halfvaluelayer........................................................... 1.5mmAlover22.Sourcetothebaseofconedistance............................ 81mm
- 4 -
[2] PHYSICAL DIMENSIONS( ) = mm
096-WK
096-RK
From2004July
600˚
4-3/
16"
(106
)
300˚
Max
. 25-
9/16
"(6
50)
Max
. 58-
1/16
"(1
475)
19-11/16"(500)
19-1
1/16
"(5
00)
Str
oke
27-9
/16"
(700
)
17-1
/16"
(450
)
Str
oke
7-7/
8"(2
00)
30-1
/2"
(775
)
3-9/16"(90)
7-1/2"(190)
20"(507)
4-3/16"(106)
Max
. 84-
1/4"
(214
0)
15-3/4"(400)
13-3/4"(350)
180˚
260˚
220˚
600˚
40-5
/8"
(103
2)
4-1/8"(104)
31-1/2"(800)
3-9/16"(90)Max. 46-7/8" (1190)
Stroke : 43 5/16" (1100)OPTION: 20" (500) or 12" (300)Horizontal Armis available.
300˚Max.75"(1904)
Min
. 19-
1/4"
(48
9)
Max
. 62-
9/16
" (1
589)
Min
. 34-
5/8"
(87
9)
M
ax. 7
7-15
/16"
(19
79)
11"(280)
3-15
/16"
(100
)
17-1
1/16
"(32
2)
3-11
/16"
(93)
47-1
/16"
(119
5)
40-5
/8"(
1032
)
42-1
/2"(
1080
)
48"(
1219
)
39"(
990.
6)
SH
OR
T C
ON
E :
15-
15/1
6"(4
04)
LON
G C
ON
E :
19-
7/8"
(505
)
46-11/16"(1185)
40-1/16"(1017)6-1/2"(165)
9-1/8"(232)
10-5/16"(261)
CENTER OFELECTRIC
- -
[3] TUBE HEAD THERMAL CHARACTERISTICS A. Interval between each exposure
Thetemperatureinsideofthetubeheadrises,whenanexposureismade.ThevalueoftheheatgeneratedismeasuredinHeatUnit(HU),whichistheproductoftubepotential,tubecurrentandexposuretime.Excessiveheatwillbeaccumulatedinsideofthetubehead,ifthex-rayisusedwithoutapropercooldownintervalbetweeneachexposure.Theexcessiveheatmaydamagethex-raytube,highvoltagegeneratororboth.
B. Duty cycleToavoidtheaccumulationofexcessheatinanefforttoprolongthetubeheadlife,acooldownintervalof60secondsormoremustbeallowedbetweeneach1secondexposure.ora30secondcooldownmustbeallowedbetweeneach0.5second(30impulses)exposure.
C. Tube head cooling curve 1. Tube Housing cooling curve 2. Anode thermal characteristics
3. Maximum rating chart
1H
U/S
HU/S
1HU/S
TUBE MODEL D-0
ANODE THERMAL CHARACTERISTICS
Hea
t Sto
rang
e (H
.U.)
Time in Minutes0 1 4 6
0000
1000
14000
10000
6000
000
FOCAL SPOT 0.8mm
0 kV
60 kV
0 kV0 kV
90 kV
Tube
Cur
rent
(mA)
Load Time (sec.)0.1 0. 0. 0. 0. 1.0 .0 .0 .0
0
0
10
Tube Housing Cooling Curve
Heat
Sto
rang
e (K
H.U.
)
Time in Minutes0 0 40 60 0 100 10 140
0
00
10
100
0
- 6 -
SECTIONTWO:PRE-INSTALLATIONINSTRUCTIONS[1] SUPPORT REQUIREMENTS
Control box:When mounting the model 096 control box, the wall and mounting hardware must be sufficient towithstanda25poundshearload.
Arm and head:TheMODEL096wallplateisdesignedformountingontwo2x4woodstudswith16inchescenters. For other types of construction, the wall and mounting hardware must be sufficient to withstanda100poundshearloadanda450poundwithdrawalforceateachofthefourmountingbolts.Thearmmountingbracket,partNo.39,mustbemountedtothewallplateusingtheboltssuppliedwiththex-ray.
CAUTION:If the MODEL 096 is to be mounted in a manner other than what is specified in this manual or ifthe hardware to be used is other than what is supplied, the support capability of the wall andthe strength of the hardware must be checked and verified to be adequate.
[2] ELECTRICAL REQUIREMENTS Power supply:
TheMODEL096x-raysystemwilloperateonapowersupplyof120VAC,+12VAC,-12VAC(108VACto132VAC).A3wireGROUNDEDcircuit,separatelyconnectedtothecentraldistributionpanelwithanover-currentprotectiondeviceratedfor15amperes.Recommendedwiresizeis12AWGBUTifthewirerundistanceistoexceed50feet10AWGisrequired.Forwirerundistancesinexcessof75feet8AWGisrequired.Linevoltageregulationmustbewithin2~5%at10.8amps.
Interconnecting wiring, control box to arm and head assemblies:6conductor12AWGisrecommendedforwirerundistancesupto50feet.Forwirerunsbetween50and75feet10AWGisrequiredandforwirerundistancesinexcessof75feet8AWGisrequired.
Concealed wiring for WK type:Concealed wiring is accomplished by bringing conduit and wires into (2) flush mounted junction boxeslocated(1)behindthecontrolboxand(1)behindthearmmountingplate.Recommendedheightsfortheflush junction boxes are : 51 5/8" for behind control box and 44 1/2" for behind wall plate. Wiring done inthis manner should extend 12 inches beyond the wall surface to allow sufficient wire for connections.
NOTE:Allconnections,workmanshipandmaterialsusedmustcomplywiththelocalcodes.
Junction Boxes
FROMPOWERSOURCE
Terminal Blockfor Control Box
Pigtail for ArmMounting Bracket
(1) ()
WALLMin 1AWG
6 4 L N 4 6
- -
[3] LOCATION OF COMPONENTSA. Arm and head assemblies for WK type:
UsingtheinformationprovidedinFIGURE1,determinethecorrectlocationfortheinstallationofthearmandheadassemblies.NOTE:Stateandlocalrequirementssupersedeguidelinesindicatedbelow.
B. Control box :Whendeterminingthelocationforthecontrolboxthefollowingradiationrequirementsconcerningoperatorpositioningmustbeconsidered.Theoperatormust;
1.havefullviewofthepatient.2.havefullviewofkVp,mA,timerselectionsandexposurewarninglight.3.beaminimumof6feetawayfromthepatient.4.beoutoflineoftheusefulbeamofradiationorbepositionedbehindaprotectivedevicewithX-ray protectionequivalentof1mmoflead.
FIGURE 1
4-1/
"
1-1
/16"
(10
4)
"(1
904)
1
"(
0)
1
"(4
0)
(66-1/16")0-/"
4-1/"
(46-/16")
220˚
( ) : WITH LONG CONE
From2004July
- -
SECTIONTHREE:INSTALLATIONINSTRUCTIONSWithin the installation and confirmation procedures are inspection/test steps which the installer must perform to insure that the installation meets the manufacturer’s specifications. These steps require the installer to record thenecessaryinformationontothe“ASSEMBLER’SINSTALLATIONSECTIONOFTHELIMITEDWARRANTYREPORTFORM”supplied,whichmustbereturnedtoBELMONTalongwiththewarrantycard.
[1] INSTALLATION REQUIREMENTSTools:Standardtoolkitincludingwirecrimpingpliers(AMP,“SuperChamp”orequivalent).1.5mm,2mm,3mmand5mmallenkeys.Instruments:Digitalmultimeterwithanaccuracyof1%,capableofmeasuring150VACand10mADC,andcapableofindicatingtrueRMSvaluewithin1second.Impulsecounter,capableofregistering1to999half-waveprimaryvoltageimpulsesatarateof60persecondoverarangeof90to100Vrms,60Hz.Standardcalculator.
POWER SUPPLY:Prior to starting the installation inspect the power supply and confirm that the power supply is 120V AC,+12VAC,-12VAC,andthatthesupplyisa3wireGROUNDEDcircuit,separatelyconnectedtothecentraldistributionpanelwithanovercurrentprotectiondeviceratedfor15amperes(RefertoPage6,[2]ELECTRICALREQUIREMENTS).Recordthevoltagereadingofpowersupplyon“Assembler’sInstallationReport”.
[2] UNPACKINGUnpacktheentirecontentsoftheshippingcarton.Includedwithintheshippingcartonare:
Identification QuantityHead............................................................................................................. 1/WK,RKRegularCone............................................................................................... 1/WK,RKLongCone................................................................................................... (1)/WK(OPTION)ControlBox................................................................................................. 1/WK,RKHeadkey...................................................................................................... 1/WK,RKCollar........................................................................................................... 1/WK,RKBalanceArm................................................................................................ 1/WKBalanceArmWrench................................................................................... 1/WKHorizontalArmW/2/ScrewCover............................................................. 1/WKArmMountingBracketW/3MachineBolt(M8x20mm),3/Boltcap....... 1/WKWallPlateW/4CoachBolts,3bolts,Washers,7/boltcapandtemplate...... (1)/WKBrakeScrew(M6x6mm)........................................................................... 2/WK,RKBrakePlug(BrassPlug).............................................................................. 2/WK,RKRetainingBolt(M6x35mm)...................................................................... 2/WKStopperScrew(M6x15mm)...................................................................... 1/WK,RKControlBoxMountingScrew(ø5.8x32mm)............................................. 4/WK,RKBrakeSpring(ø5)........................................................................................ 1/RKBase............................................................................................................. 1/RKColumn........................................................................................................ 1/RKSlidingPost.................................................................................................. 1/RKSwingArm................................................................................................... 1/RKGasPump..................................................................................................... 1/RKSeat.............................................................................................................. 1/RKLagBolt(ø8x45mm)................................................................................. 5/RKManual......................................................................................................... 1/WK,RK
Inspectcontentsofshippingcartonfordamageormissingcomponents.
- 9 -
[3] ARM ASSEMBLY INSTALLATION[3-1] WK TYPE
TheINSTRUCTIONSgivenbelowareformountingthearmandheadassemblyontwo2X4woodstudswith 16-inch centers. Should the MODEL-096 be mounted in a manner other than what is specified here,the wall and the strength of the hardware used must be checked and verified as being adequate to withstanda100poundshearloadanda450-poundwithdrawalforceateachofthefourmountingbolts.When using concealed wiring, a flush mounted junction box with the necessary conduit and wiring must bepre-installed at 40 5/8 inches from the floor and centered between the two studs (refer to template).
A. WALL PLATE (FIGURE 2):
1.Tapethewallmountplatetemplatetothewall,positioningit so that the holes are aligned with the vertical 2 X 4" stud.
NOTE:Innoinstanceisthewallmountplate,orthearmmountingbracket,tobeasinglestud.
2.Marktheholelocations.3. Using a 3/16" drill, drill a pilot hole approximately 2" deep for eachplatebolt.CAUTION:Donotuselargerdia.drill. Theelectricalwireaccessholeshouldbepredrilledusingthe height from the floor specified on the mounting template.4.Placethewirethroughtheholeintothestudmountwallplate andmounttheplatetothestudwith4coachboltssupplied. DO NOT FULLY TIGHTEN BOLTS.5. Holding plate firmly against the wall, place a level(a)upright onthesurface.Ifthewallisnotplumb,useshimsbehind theplatetolevel.6.Placealevel(b)acrosstopedgeofwallplate,levelandtightenboltssecurely. NOTE:Finallevelingofwallplateisdescribedonpage13.7.Putboltcaptoeachheadofbolt.
B. ARM MOUNTING BRACKET (FIGURE 3):
1.Removeaccesscoverfrombottomofarmmountingbracket.Snakeelectricalinterconnectingwires throughbracketandoutaccesshole.2.UsingM8X20mmboltwithwashersinlowermountingholeandtwoM8X20mmboltsintop mountingholes,mountarmmountingbrackettowallplate.DONOTFULLYTIGHTEN.3.Placinglevelacrosstopedgeofarmmountingbracket,levelbracketthentightenboltssecurely.4.Puttheboltcaptoeachheadofbolt. NOTE:FinallevelingofwallmountingbracketisdescribedonPage13.
FIGURE 3
Access Hole
Coach Bolt
Level(b)
Level(a)
Bolt Cap
FIGURE 2
Access HoleAccess Cover
M x 0Bolt
Level(b)
WasherBolt Cap
C. If wall plate is not used, other optional, special, wall plate for "pas thru" (4X4") installation must be installed.
- 10 -
D. HORIZONTAL ARM (FIGURE 4):
1.Cutpullstringonhorizontalarm.DONOTREMOVESTRING. ALLOWONEENDTOEXTENDBEYONDMALEBARB ANDTHEOTHERENDTOEXTENDBEYONDTHE FEMALEMOUNT.2.Placeathrustwasherovertheholeofarmmountingbracket, andinsertmalebarbintoarmmountingbracket,allowingpull stringtoextendthroughaccessopeningonbottomofthearm mountingbracket.3.Inserttworetainingboltssecurelyintoupperthreadedholesofarm mountingbracketandtightensecurely.
IMPORTANT:Theretainingboltsmustsecurelyengagetheannulargroovehorizontalarm,theremovaloftheretainingboltswillallowthehorizontalarmtorisevertically,andoutof,thearmmountingbracket. DO NOT FULLY TIGHTEN.4.Insertbrakeplugthenbrakescrew(M6x6mm)intothelowerthreadedholeofthearmmountingbracket.5. Place a level on the horizontal arm and confirm that the arm is level in its left and right swing positions. NOTE:FinallevelingofhorizontalarmisdescribedonPage13.
E. BALANCE ARM ASSEMBLY (FIGURE 4a):
WARNING:DONOTRELEASEARMHOLDINGBANDUNTILTHEX-RAYHEADHASBEENINSTALLED.BALANCEARMASSEMBLYISSPRINGLOADEDANDCANCAUSEEQUIPMENTDAMAGEANDINJURYIFNOTHANDLEDINTHEPROPERMANNER.
1.DONOTREMOVEARMHOLDINGBAND.2.Securepullstringtocableandpullingtheopposite end,snakecablethroughhorizontalarmandarm mountingbracket.3.Insertbrakeplugthenbrakescrew(M6X6mm) intothehorizontalarmcollar. DONOTFULLYTIGHTEN.4.Removeendcapscrewandopenendcap.5.Insertstopperscrewintoupperthreadedholeinside horizontalarmandtightensecurely. CAUTION:Ifstopperscrewisnottightened securely,thescissorsarmcanmoveverticallyup andoutofthehorizontalarm6.Cutcableandinterconnectingwirestoaworkable length. Strip 3/8" of wire insulation from each lead. Withwirecrimpingpliersusesuppliedwirenuts tomakewireconnections.7.Insertconnectedwiresintothearmmounting bracketandsecuretheaccesscovertothebottom ofthearmmountingbracket.8.Secureendcapwithendcapscrew,andplacea screwcover.
Brake Plug
Brake Screw
Thrust WasherRetaining Bolts
Pull String
FIGURE 4
FIGURE 4a
Arm Holding Band
Brake Plug
Brake ScrewEnd Cap
Screw Cover
Stopper ScrewAccess Cover
Access Cover Screw
End Cap Screw
From2004July
- 11 -
[3-2] RK TYPE (FIGURE5)
1. Fix the base on the floor with lag bolts (supplied) or withappropriatemeans.
CAUTION :MAKE SURE THE BASE IS
FIXED ON THE FLOOR FIRMLY.
2. Insert the slidingpostwith columncover into thecolumn.
3.Installthecolumnonthebasewithmountingbolts.Make it vertical with adjusting bolts.
4.Putthethrustwashertotopoftheslidingpostandinstalltheswingarmassemblytoslidingpost.
5.Set the stopper screw into lower threaded hole ofswingarm2.
6.Set thebrake plug then brake spring and brakescrewintotheupperholeofswingarm2.
TightenthebrakescrewIFARMDRIFTS. DO NOT FULLY TIGHTEN.
7.Run the cable from swing arm1 through a cableguide.
8.Slideupthebackrestcushiontothetopofcolumn.
9. Insert the gas pump into the gas pump bracket.Mounttheseatonthegaspump.
10.Refertopage12forHeadassemblyinstallation.
11.Refertopage13forControlboxinstallation.
12.Performthepostinstallationinspection.(page14)
Brake Screw
Stopper Screw
Thrust Washer
Brake SpringBrake Plug
Swing Arm
Swing Arm 1
Sliding Post
Column Cover
Column
Cable Guide
Cable
Mounting Bolt
Adjusting Bolt
Lag Bolt
Base
Gas Pump
Gas Pump Bracket
SeatBackrest Cushion
FIGURE 5
- 1 -
1mm
Head Key
Arm Collar
Balance Arm
Balance ArmWiring
Head ShaftStopper Ring
Head Yoke
Terminal
mm
Yoke Inside Cover
Arm Holding Band
(a)
(b)
3 Blue4 Brown5 Red6 Yellow7 Gray8 Green/Yellow
[4] HEAD ASSEMBLY INSTALLATION (FIGURE 6):
FIGURE 6
1.Removeascrew(a)onarmcollar,andplacethearmcollaroverthestopperringontheheadshaft.
(DirectionofarmcollarisshowninFIGURE6.)
2.Removetheyokeinsidecoverbylooseningscrew(b).
3.Makingsurethestopperringandarmcollarisplacedontheheadshaft, insert thewiringsofbalancearmthroughtheheadshafttotheheadyoke.
4.Inserttheheadshaftintobalancearmassembly,andwhileholding thehead inposition, installheadkeysecurelyintoretaininggroove.
5.Slide the armcollar upward to proper position andsecureitinplacewithascrew(a).
6.Loosen5 screwson the terminal using a small dia.screw driver, and insert thewirings of balance armassembly into the terminal according to the color.(FIGURE6-1)
7. Retighten the screws on the terminal and confirm that the wirings are fixed on the terminal.
8.RemoveM5PhillipsheadscrewfromearthterminalandsecureNo.8wiringtogethertoearthterminal.
9.Reattachtheyokeinsidecoverwithascrew.
10.Removearmholdingband.
4
6
Small Diameter Screw Driver
Earth Terminal
Wirings of Balance
Arm Assembly
FIGURE 6-1
[5] CONTROL BOX INSTALLATION
The wall and the strength of the hardware used must be checked and verified as being adequate towithstanda25poundshearload.
A flush mounted junction box with the necessary conduit and wiring must be pre-installed at 51 5/8" fromthe floor.
NOTE:Refertothecontrolboxtemplate,and: 1. Be certain the electrical wire entry hole is aligned with the junction box. 2.Thatthereisadequatesupportinthewalltosecurethecontrolbox.
From2004July
- 1 -
A. CONTROL BOX - MOUNTING (FIGURE 7):
1.Tapethecontrolboxtemplatetothewallattherecommendedheight.1a.Confirm relationship of access hole in for the electric wires with the entry hole for the wires in the back ofthecontrolbox.2. Using a 3/32" drill, drill a pilot hole 2" deep for each mounting screw.2a.Themethodofdrillingthepilotholeand,thehardwareusetosecurethecontrolboxdependuponthestructure.3. Drive two wood screws into upper two holes remaining about 3/4" undriven. (Fig.7a)4.RemovetwoM3Phillipsheadscrewsfromtopofthecontrolboxandopenfrontpanel.(Fig.7b)5.Removearestrictionplate.(Fig.7c)6.Snakepowersupplycablelinesandinterconnectingwiresthroughaccessholeinbackpanel.7.Hookthecontrolboxchassistowoodscrewsdriveninstep3abovethroughtwomountingholes onuppersideofchassis.Tightenscrewsslightly.8.Attachtwowoodscrewstomountingholesonlowersideofbackpanel.(Donotfullytighten.)(Fig.7d)9.Placinglevelacrosstopedgeofthecontrolbox,level,thentightenfourscrewessecurely.
a
b
c
d
FIGURE 7
B. CONTROL BOX, WIRING (FIGURE 8-a & 8-b)
WARNING:MAKESURETHEPOWERSUPPLYISTURNEDOFFATTHECENTRAL DISTRIBUTIONPANEL.1. Strip approximately 3/8" of insulation off the power supply leads and interconnecting cables.2.Followingwiringdiagram,connectthosewirestotheterminalblockofcontrolbox.3.Settherestrictionplatetotheoriginalplace.
Junction Boxes
FromPower
Source
Terminal Blockfor Control Box
Pigtail for ArmMounting Bracket
WALL
L N 4 6 6 4
GR
EEN
/YEL
LOW
BLU
E(W
HIT
E)
BR
OW
N(B
LAC
K)
BLUE
RED
GRAYGREEN/YELLOW
YELLOW
BROWN
FIGURE 8-a46
LN
FIGURE 8-b
- 14 -
Bolt CapTop Mounting Bolt
Bottom Mounting Bolt
Brake Screw
LEVEL
#
#1
FIGURE 10-b
LEVEL
Wall error adjustment;installshimsbehindthewallplate
FIGURE 10-a
C. CLOSING FRONT PANEL (FIGURE 9).
CAUTION: BEFORECLOSINGTHE FRONTPANEL, PERFORMPOST INSTALLATIONCON-FIRMATION(PAGE20).
1. Confirm all the post installation confirmation are performed.2.ClosethefrontpanelandsecuretwoM3phillipsheadscrewsonthetoppanel.
FIGURE 9
SECTIONFOUR:POSTINSTALLATIONINSPECTION
[1] ARM ASSEMBLY1.Incorrectlevellingofthewallbracketcancausearmdrift.First,checklevelwitharmsinposition#l.If not correct, bracket must be adjusted by placing shims behind the wall plate (FIGURE 10-a).IMPORTANT: Iftheendofthehorizontalarm#1ispitchedbelowlevel,thenthetubeheadwilldriftawayfromthewall.Iftheendofthehorizontalarm#1ispitchedabovelevel,thenthelevelarmwillrequireonlyminimumadjustment of brake (friction) screw.2. Check level in position #2. If not correct, adjust as follows: (FIGURE 10-b) a)Removeboltcapsonmountingbolts. b)SLIGHTLYloosentwotopmountingbolts. c)Shiftthebracketleftorrightuptothearmsarcaccuratelylevelled. d)Movethehorizontalarmtoposition#1. e)Fullytightentwotopmountingbolts. f)Fullytightenbottommountingbolt. g)Puttheboltcaptoeachheadofmountingbolt.
NOTE:SLIGHTTENDENCIESTODRIFTCANBECORRECTEDBYTIGHTENING BRAKESCREWSINHORIZONTALARMAND/ORWALLBRACKET. DONOTTIGHTENBEYONDWHATISREQUIREDTOPREVENTDRIFT.
- 1 -
[2] BALANCE ARM ASSEMBLY
1.Placethebalancearmassemblyintoposition.2.If either balance arm drifts either higher or lower from the set position, remove the spring adjuster covers and with the supplied wrench adjust the balance arm springs (FIGURE 11).
Adjustment Nut
less tensionLOOSEN
more tension TIGHTEN
Balance Spring
Cover
FIGURE 11
[3] HEAD POSITIONING
A.Placeheadintoposition.
B. If head drifts from the set position, adjust the brake screws according to the following procedures.(FIGURE12)
1.Removetheyokeoutsidecoverbylooseningcoverscrew. 2. Adjust 6 brake screws using phillips screw driver. 3. After adjustment, reattach the yoke outside cover with the cover screw.
Phillips Screw Driver
Yoke Outside Cover
Cover ScrewBrake Screw
FIGURE 12
- 16 -
SECTIONFIVE:CONTROLIDENTIFICATIONANDOPERATION[1] CONTROL IDENTIFICATION
W A R N I N G THIS X-RAY UNIT MAY BE DANGEROUSTO PATIENT AND OPERATOR UNLESS SAFE EXPOSURE FACTORSAND OPERATING INSTRUCTIONS ARE OBSERVED.
MODEL 096 0kVp 10mA
P C F
T1 T2 T3 T4 T5
a b c
1514
2
3
4
98
76
121110
16
5
1
13 (1) Main Power switch(2) Ready Lamp(3) Exposure Time Adjusting Sw. (Up)(4) Exposure Time Adjusting Sw. (Down)(5) Tooth Selection Switch (T1)(6) Tooth Selection Switch (T2)(7) Tooth Selection Switch (T3)(8) Tooth Selection Switch (T4)(9) Tooth Selection Switch (T5)(10) Patient Size Selection Switch(11) Cone Type Selection Switch(12) Film Speed Selection Switch(13) Exposure Time Display Window(14) Exposure Warning Light(15) Exposure Switch(16) Technical Switch
[2] FUNCTION OF CONTROLS
Main Power switch Pushingrightsideofthisswitchenergizesthex-rayunit. (Ready lamp and pre-selected lamps for patient size, cone type and film speed illuminates.) ItisrecommendedtokeepthisswitchOFFwhentheunitisnotinuseinordertopreventanacci-
dentalexposure.
Ready Lamp Thislamplightswhenthelinevoltageiswithinoperablerange. Whenthislampisnoton,exposurecannotbemade.
Exposure Time Adjusting Switches Bymomentarilypushing (or )switch,exposuretimedisplayedincreases(ordecreases)byone
step.Bykeepingtheswitchdepressedmorethan2sec.,exposuretimedisplayedincreases(orde-creases)continuouslyuntiltheswitchisreleased.
Tooth Selection Switch (T1 ~ T5) Pushingoneoftheseswitchessettheexposuretimeautomaticallyincombinationwithfollowing ~ . T1:IncisorofMandible T2:IncisorofMaxilla,Cuspid&PremolarofMandible T3:Cuspid&PremolarofMaxilla,MolarsofMandible,Bitewing T4:MolarsofMaxilla,BitewingMolars T5:Occlusal
1
3
2
4
5 9
10 1256789
~
- 1 -
Patient Size Selection Switch Pushingthisswitchalterstheselectionofpatientsize(small->medium->large->small)andsets
theexposuretimeaccordingly.
Cone Type Selection Switch Theexposuretimecorrespondingtotheconetypebeingused(StandardRegularConeorOptional
LongCone)canbeselectedbythisswitch.
Film Speed Selection Switch Three types of film speed can be registered. Pushing this switch momentarily indicates the film
speednumberbeingselectedinexposuretimedisplaywindow . Depressing the switch for more than 2 seconds alters the film type being selected.
NOTE : Setting or adjusting the exposure time manually (with or switch) supersedes ~ functions.
Exposure Time Display Window Normallytheexposuretimeselectedisdisplayed.
1.E.00~E.12 :Errorcode[Seepage19ofthismanual] 2.F.00~F.15 :Filmtype[Seepage21&22ofthismanual] 3.TubeCurrent:Thetubecurrentofthelastpulseoftheexposurecanbedisplayediftheexposure switchiskeptdepressedafterexposureisoverandtechnicalswitch isdepressed. 4.bu.0,bu.1 :BuzzerON/OFFwhenaswitchisactivated.[Seepage23ofthismanual] 5. FIn :Confirmation of tube current [See page 20 of this manual] 6. PH.0 ~ PH.F :To adjust tube current at beginning of exposure [Refer to service manual] 7. EP.0 ~ EP.F :To adjust tube current when stabilized [Refer to service manual] 8. Pt.0 ~ Pt.F :To adjust preheat time [Refer to service manual]
Exposure Warning Light Illuminationofthislightindicatestheunitisproducingx-radiation.
Exposure Switch DeadmanTypeexposureswitch.Whenmakinganexposure,depress thisswitchandkeepitde-
presseduntiltheexposurewarninglight andtheaudiblewarningterminate. Failuretokeepthisswitchdepressedwillresultinprematureterminationoftheexposure.
Technical Switch Thisswitchisexclusivelyfortheinstallerandservicepersonnel.Itisusedforfollowingpurposes: 1.Thetubecurrent(mA)ofthelastpulseoftheexposurecanbedisplayedinexposuretimedisplay
window iftheexposureswitchiskeptdepressedevenaftertheexposureisoverandthistechni-calswitchisdepressed.Displaywillreturntoexposuretimewhentheexposureswitchisreleased.
2.Priorityofselection(PatientSize,ConeType,FilmSpeed)canbechangedwhenthemainpowerswitchisturnedonwhilethisswitchisdepressed.[SeesectionSevenofthismanual]
3. Memorizing : After setting film speed, priority of selection and/or buzzer ON/OFF, this switch isusedformemorizethesesettings.[SeesectionSevenofthismanual.]
10
11
12
13
14
15
16
5 12
13
16
14
13
- 1 -
[3] OPERATING PROCEDURES
1. TurnONthemainpowerswitch .
2. Confirm that ready lamp isilluminated. NOTE: The ready lamp will not illuminate unless the incoming line voltage is correct and within the x-ray’s operable range.
3. Selecttheappropriatetoothtype( ~ ), and confirm if the pre-selected conditions(patientsize ,conetype and film speed )aresuitable forradiographing.
NOTE: To manually set the exposure time, depress either manual exposure time adjust switch( or ) until the desired exposure time is displayed in exposure time display window . While the unit is in manual mode, other selection switches( ~ ) do not affect exposure time. (All the tooth selection lamps are off.)
Toreturntotheautomaticexposuretimeselectionmode,depressany oneoftoothselectionswitches.
4. Depresstheexposureswitch .Whentheexposureswitchisdepressed, theexposurewarninglamp illuminatesandtheaudiblewarningsounds. Donotreleasetheexposureswitchuntiltheaudiblewarningandthe warninglampterminate. Failuretokeeptheswitchdepressedwillresult intheexposurebeingterminatedprematurely.
5. To continue to radiograph other teeth, just select appropriate tooth selectionswitch.
IMPORTANT : To protect x-ray tubehead from heat accumulation, wait for 60 times of exposure time between exposures. [Ex. 30 second wait interval for each 0.5 sec.(30 impulses) exposure]
6.AfteruseturnOFFthemainpowerswitch inordertopreventaccidental exposures.
NOTE : If the unit is left over 8 minutes without being operated and the main power switch is kept on, figure 1 runs through the exposure time display window. This does not mean that a malfunction of the unit has occurred, but saves energy. The unit returns to normal condition by pressing any one of the switches except the exposure switch.
1
2
5 9
10 1211
3 4
14
15
13
5 12
1
- 19 -
[4] ERROR CODES
Whenabnormalconditionexistsintheunit,ormalfunctionoccurs,errorcodeisdisplayedinexposuretimedisplaywindow.Pleaserefertothetablebelow.
ErrorcodeE.00E.01E.02E.03E.04E.05E.06E.07E.08E.09E.10E.11E.12
ConditionExposureswitchwasreleasedbeforethe exposureterminates.Exposureswitchwasdepressedwithin10sec.ofpreviousexposure.Exposureswitchwasdepressedwithin3sec.afterthemainpower switchhasbeenturnedon.Linevoltagewaslessthan 90%ofratedvoltage.Linevoltagewasmorethan 110%ofratedvoltage.Excesscurrentduringexposure.Tubecurrentofthelastpulsewaslessthan7.5mA.Tubecurrentofthelastpulsewasmorethan12.5mA.Tubecurrentduringex-posurewaslessthan5mA.Tubecurrentduringex-posurewasmorethan15mA.Malfunctionofthemicrocomputer. Exposureswitchorex-posurecircuithadbeenON,whenmainpowerswitchisturnedon.Tubecurrentisdetectedduringpre-heatingperiod.Tubecurrentisdetectedwhenmainpowerswitchisturnedon.
Steptobetaken Allthetoothselection switchesblink. Depressoneoftheswitch. A10seconddelayisbuilt inbetweeneachexposure. Releaseexposureswitch. Turnoffthemainpowerswitchandwaitfora while.Turnonthemainpowerswitchagain.
PossiblesolutionReleaseexposureswitch afterexposurelamp turnsoff.There is to be an "wait"intervalof60times ofexp.timebetween successiveexposures.Exposureswitchshould bedepressedaftertheready lampcomesON. Iflinevoltageisless than90%ofratedline voltage,correctitby usingstep-uptransformer.Iflinevoltageismore than110%ofratedline voltage,correctitby usingstep-downtransformer.Conducttheconfirmation oftubecurrentdescribedinsectionsix,item[2]on page20.Refertotheservicemanual.
- 0 -
SECTIONSIX:POSTINSTALLATIONCONFIRMATION
[1] CONFIRMATION OF POWER SUPPLY VOLTAGEAs specified in Electrical Requirements (Page 6), power supply voltage must be within the operablerange of 108~132V AC. Confirm the power supply voltage again before turning on the unit.1.Openthefrontpanelofcontrolboxbylooseningtwoscrewsontopofthecontrolbox.2.Settherangeofdigitalmultimeterat200VAC,connectprobesofmultimetertoLandNof terminalblockofcontrolbox.3. Confirm that the reading is 120V ±10%(108~132VAC). NOTE :096X-raycannotbeoperatedunlessthepowersupplyvoltageiswithinthisrange.
[2] CONFIRMATION OF TUBE CURRENTModel 096 x-ray incorporates self diagnose system to check if the tube current is within specifiedrangebothatthebeginningofexposureandduringstabilizedperiod.1.WhiledepressingtoothselectionswitchesT1,T4&T5together,turnonthemainpowerswitch.2.Exposuretimeof0.50isdisplayedandreadylightison. [Ifnot,turnoffmainpowerswitchandrepeat1.] ThenreleaseT1,T4&T5switches.3.Makeanexposurebydepressinghandexposureswitch. WARNING:X-RADIATIONISGENERATEDFOR0.5SEC.4. Confirm that "F I n" is displayed at exposure time display window. Then,turnoffthemainpowerswitch.5. If "PH. " and "EP. " are displayed alternately, follow Step 6 through 8 below. 6. When "PH. " and "EP. " are displayed alternately, leave the unit for about 30 seconds until display returns to "0.50". Then make an exposure again and confirm that "F I n" is displayed. 7. Repeat Step 5 & 6 until "F I n" is displayed.8.Record final PH & EP values in "Assemblers Installation Section of Limited Warranty Report Form" if proceduresinStep5through7areperformed.
[3] CONFIRMATION OF EXPOSURE WARNING LAMP & BUZZERA.EXPOSUREWARNINGBUZZER 1. Make an exposure and confirm that the exposure warning buzzer located within the control box isactivatedduringtheentireexposure.B.EXPOSUREWARNINGLAMP Exposurewarninglampislocatedonthefrontpanelofthecontrolbox, 1. Make an exposure and confirm that the warning lamp illuminates during the exposure.
[4] CONFIRMATION OF LINE VOLTAGE REGULATION1. Make sure that main power switch is "OFF". 2.Openthefrontpanelofcontrolboxbylooseningtwoscrewsontopofthecontrolbox.3.Settherangeofdigitalmultimeterat200VAC,connectprobesofmultimetertoLandNof terminalblockofcontrolbox.4.Turnthemainpowerswitchon,andsettheexposuretimeat2.00sec.withmanualswitch .5.Recordtheno-loadlinevoltage(VN)indicatedbythemultimeterbeforeexposure.6.Makeanexposureandrecordtheloadvoltage(VL)indicatedbythemultimeterduringexposure. WARNING :X-RADIATIONISGENERATEDFOR2SECONDS. NOTE:Readthemultimeterwhenthevalueisstabilized(aboutonesecondafterexposure).7.CalculatelinevoltageregulationR(%)intheformulabelow:
VN-VL R = X 100 Record this value in "Assemblers Installation Report". VL
NOTE: LINEVOLTAGEREGULATIONMUSTNOTEXCEEDTHERANGEOF2~5%. IFITISGREATERTHAN5%,THESIZEOFTHEPOWERSUPPLYWIRESMUSTBE INCREASED.REFERTOTHEPOWERSUPPLYREQUIREMENTSOUTLINEDON PAGE5TODETERMINETHECORRECTWIRESIZENECESSARY.
- 1 -
SECTIONSEVEN:INITIALSETTING[1] FILM SPEED
As factory installation, following three kinds of film speed are registered to be selected byFilmSpeedSelectionSwitch:
a = Film speed No. F.09 (equivalent to ISO speed group "D", or Kodak Ultra-Speed film) b = Film speed No. F.04 (equivalent to ISO speed group "F/E", or Kodak InSight film)c = Film speed No. F.02 (equivalent to ISO speed group "F")
Including these three, Model 096 can provide 16 different types of film speed and any three of themcanberegisteredforeasyselection.If the doctor uses different speed of film, or prefers darker (or lighter) radiograph, substitute speedcanberegisteredasfollows:
1.Whiledepressingtechnicalswitch ,turnonthemainpowerswitch . Film type lamp "a" is lit, andF.09isdisplayedinexposuretimedisplaywindow . Then,releasetechnicalswitch.
2.Bydepressing switch(or switch),increase (decrease) film speed number until desired numberisdisplayed.[RefertoExposureTimeTableonnextpage.]
3.Depresstechnicalswitch , an electronic chime sounds and the selected film speed number is registered at film type "a".
4.Turnoffthemainpowerswitch.
5. If different film speeds are to be registered at "b" and "c", depress "F"switch afterstep1above to light the appropriate film type lamp, and repeat steps 2 & 3.
12
13
16 1
16
- -
TABLE 1 : FILM SPEED AND EXPOSURE TIME (REGULAR CONE)
TABLE 2 : FILM SPEED AND EXPOSURE TIME (LONG CONE)
T10.00.00.00.00.040.00.060.00.00.100.10.10.10.00.40.9
T20.00.040.00.060.00.00.100.10.140.10.190.40.90.0.410.0
T30.040.00.060.060.00.100.10.140.10.00.40.90.0.410.00.
Patient SizeToothF. 00F. 01F. 02F. 03F. 04F. 05F. 06F. 07F. 08F. 09F. 10F. 11F. 12F. 13F. 14F. 15
SMALL MEDIUM LARGE(UNIT : SEC.)
(UNIT : SEC.)Patient Size
ToothF. 00F. 01F. 02F. 03F. 04F. 05F. 06F. 07F. 08F. 09F. 10F. 11F. 12F. 13F. 14F. 15
SMALL MEDIUM LARGE
T40.00.060.00.090.100.10.160.10.0.0.10.0.40.40.660.6
T50.00.090.110.10.160.190.0.0.0.0.40.40.660.10.91.1
T10.00.040.00.00.060.00.090.110.140.160.190.40.0.0.0.4
T20.00.060.00.090.110.10.160.190.0.0.10.0.40.40.660.1
T30.060.00.090.100.10.160.190.0.0.0.0.40.40.660.10.9
T40.00.100.10.10.10.00.0.90.60.440.00.60.60.1.01.
T50.10.10.10.00.0.10.60.440.40.60.60.1.01.1.11.6
T10.040.00.060.060.00.100.110.140.10.190.40.90.0.410.40.
T20.060.00.100.110.140.160.190.40.0.0.0.40.0.660.11.00
T30.00.090.110.10.160.190.40.0.0.410.40.0.660.11.001.1
T40.100.10.10.10.00.0.10.60.440.40.60.60.91.01.1.1
T50.10.10.0.0.10.0.440.40.660.60.91.01.1.61.6.
T10.00.00.060.00.00.100.10.10.10.00.0.10.60.440.00.6
T20.00.00.100.10.10.10.00.0.90.60.410.00.60.10.1.0
T30.00.100.10.140.10.00.0.90.60.440.00.60.10.1.01.
T40.110.140.160.190.0.0.0.0.40.0.660.11.001.11.411.6
T50.160.190.40.0.0.410.40.0.10.11.001.11.411..00.44
T10.00.00.100.110.140.10.190.40.90.0.410.00.0.10.11.00
T20.110.140.10.190.40.0.0.410.40.0.660.11.001.11.411.
T30.140.160.190.0.0.0.410.40.0.10.11.001.11.411..00
T40.10.0.0.10.60.440.40.60.60.91.01.1.61.6..6
T50.0.10.0.440.40.660.60.91.11.1.61.6..0.00.00
T10.00.100.10.140.10.00.40.90.60.410.00.60.10.1.001.
T20.140.10.00.40.90.0.410.00.0.10.11.001.1.411..1
T30.10.190.40.0.0.410.00.0.10.1.001.1.411..1.44
T40.0.0.10.0.440.40.660.60.91.11.1.6.00..0.00
T50.10.0.40.40.660.10.91.11.411.6.00..0.00.00.00
- -
L
N
Control Box Head
X-RayTube[D-0]
6
4
6
4AVR 1
1
1
1
H.V. Transformer
Fil. Trans.
PowerSwitch
Exposure Switch
Fuse
Blue
Yellow Yellow
Gray Gray
Blue Blue
BrownBrown
Red
Green/Yellow Green/Yellow
1 CN1 16
1 CN
CN4
CN
CN
N.C.
T.B.T.B.
T.B. T.B.
16
500Ω
Brown
NC
CN1
Fuse
Control Board096P-CN00
Power Generator Board096P-PW00
RY
Green/Yellow
Arm
APPENDIXONE:CIRCUITDIAGRAM
[2] PRIORITY OF SELECTION
Asfactoryinstallation,followingselectionlampslightwhenthemainpowerswitchisturnedon:
PatientSize :MediumCone :RegularFilm Speed : "a"
Ifnecessary,thisprioritycanbechangedasfollows;[For example, at pedodontistry, patient size of "small" should be preferentially selected.]
1.Whiledepressingtechnicalswitch ,turnonthemainpowerswitch.2. Select the patient size "small" by depressing patient size selection "P"switch .3.Depresstechnicalswitch , an electronic chime sounds and the patient size of "small" will be stored as primaryselection.4. Priority of selection for cone type and film speed can be changed by same procedures.
[3] ELECTRONIC CHIME ON/OFF
Asfactoryinstallation,electronicchimesoundswheneachswitchisdepressed.Ifpreferred,thissoundcanbeeliminated.
1.WhiledepressingtoothselectionswitchesT1&T2together,turnonthemainpowerswitch.2. "bu.1" will be displayed in exposure time display window .3.Bydepressingeither or ( or ), display changes to "bu.0".4.Thendepresstechnicalswitch ,andturnoffthemainswitch.
NOTE :ExposureWarningBuzzerandalarmsoundoferrorcodecannotbeeliminated.
16
1610
163 4
13
- 4 -
APPENDIXTWO:PARTSIDENTIFICATION[1] ARM AND HEAD ASSEMBLY OF WK TYPE
[2] CONTROL BOX ASSEMBLY (60)
347
48
4
67
5
2
1
49
279
1146
12
1413
15
26
23
8
221718
14
1317
2425
1420
2119
10
16
14
2932
3031
33
28
3435
3738
393031
4142
4443
40
36
45
50
From2004July
- -From2004July
ID.No. PartsNo. Description QTY USA Code
1 E04-EHLL0A0 X-Ray Head Assembly (RAL-900) 1 096-1010
E04-ECPE0G0 Yoke (RAL-900) 1 096-100
E04-EHLL1A0 Housing Cover Set (RAL-900) 1 096-100
4 E04-ECPRB0 Lock Ring (R1-100) 1 096-1040
E04-ECPR6A0 X-Ray Exposure Sleeve 1 096-100
6 E04-ECPR1D0 Regular Cone (RAL-900) 1 096-1060
E04-EHLL1A0 Long Cone (RAL-900) (Option) (1) 096-100
E04-EHLLA0 Balance Arm Assembly (RAL-900) (1) 096EHLLA0
9 E04-ECLS01A0 Stopper Ring 1 096-1090
10 E04-ECPE1B0 Joint No. 1 096ECPE1B0
11 E04--------------- Collar Screw (SUS M4-10) 1 096SRWM0410
1 E04-ECQR4B0 Collar (R1-100) 1 096ECQR4B0
1 E04-ECQR0C0 Spring Adjuster Cover 096ECQR0C0
14 E04-ECQRB0 Crevice Cover 4 096ECQRB0
1 E04-ECPE19F0 Left Cover for Joint No. 1 096ECPE19F0
16 E04-ECPE1F0 Right Cover for Joint No. 1 096ECPE1F0
1 E04-ECPJ64C0 Cover for Joint No. 096ECPJ64C0
1 E04-ECPJB0 Joint No. 1 096ECPJB0
19 E04-ECPJ6F0 Left Cover for Joint No.1 1 096ECPJ6F0
0 E04-ECPJ6F0 Right Cover for Joint No.1 1 096ECPJ6F0
1 E04-ECPE1B0 Joint No.1 1 096ECPE1B0
E04-ECPJ60A0 Arm Cover No. 1 096ECPJ60A0
E04-ECPE0B0 Balance Arm No. 1 096ECPE0B0
4 E04-ECPJ9A0 Arm Cover No.1 1 096ECPJ9A0
E04-ECPE1B0 Balance Arm No.1 1 096ECPE1B0
6 E04-ECQRA0 Cushion Absorber 1 096ECQRA0
E04-ECLR9B0 Head Key 1 096-10
E04-EHLK90A0 Horizontal Arm Ass'y (00mm) (RAL-900) (1) 096-10
E04-EHLKA0 Horizontal Arm Ass'y (00mm) (RAL-900) (1) 096-11
E04-EHLKA0 Horizontal Arm Ass'y (00mm) (RAL-900) (1) 096-1
E04-EHLK9A0 Horizontal Arm Ass'y (60mm) (RAL-900) (1) 096-1
E04-EHLK91A0 Horizontal Arm Ass'y (1000mm) (RAL-900) (1) 096-14
9 E04--------------- Horizontal Arm 1 096-190
0 E04-ECLS06A0 Brake Plug 096-100
1 E04--------------- Brake Screw (M6-6) 096-110
E04-ECLS09A0 Stopper Screw 1 096-10
E04-ECLJ6A0 End Cap (R1-100) 096-10
4 E04--------------- End Cap Screw (M6-1) 096-140
E04-ECNR4A0 Hole Plug for End Cap (R1-100) 096-141
6 E04-EHLL0A0 Arm Mounting Bracket Ass'y (RAL-900) (1) 096-10
E04--------------- Machine Bolt (M-0) 096-160
E04-ECPRA0 Bolt Cap (RAL-900) 096-10
9 E04-ECPR44A0 Retaining Bolt 096-10
40 E04-EHLL1A0 Arm Mounting Bracket Ass'y (RAL-900) (1) 096-190
41 E04-ECPR4B0 Bottom Cover 1 096-1400
4 E04--------------- Bottom Cover Screw (M-6) 096-1410
4 E04-ECPRA0 Bolt Cap (RAL-900) 4 096-140
44 E04--------------- Coach Bolt (ø9-) (RAL-900) 4 096-140
4 E04-ECPJ19A0 Wall Mount Plate (RAL-900) 1 096-160
E04-ECPJ1A0 Wall Mount Plate for Cover Type (1) 096-161
46 E04-EHLL11A0 Wire Harness in Balance Arm 1 096-101
4 E04-ECNR1A0 Yoke Side Cap (R1-100) 1 096-160
4 E04-ECPJ1A0 Yoke Inside Cover (RAL-900) 1 096-101
49 E04-ECLJA0 Adjust Wrench 1 096-10
0 E04-EHLL14A0 Cover Set for Wall Mount Plate (RAL-900) (Option) (1) 096-16
60 E04-EHLL0A0 Control Box Assembly (for 10V) (RAL-900) (1) 096-1000
61 E04-ECPE01A0 Chassis (R1-100) 1 096-1440
6 E04--------------- Fuse (F1/F - 10A) 096-140
6 E04--------------- Terminal Block (4P) 1 096-1460
64 E04--------------- Power Switch 1 096-140
6 E04-ECPJ0D0 Covering Plate 1 096-140
66 E04--------------- Timer Board 1 096-1490
6 E04-ECPB01G0 Front Cover 1 096-100
6 E04--------------- Top Screw (M-) 096-110
69 E04--------------- Fuse (F - 0.A) 1 096-10
0 E04--------------- Wood Screw for Chassis (ø.-) 4 096-10
1 E04--------------- Fuse (F4 - 1A) 1 096-140
E04--------------- Terminal Block (P) 1 096-10
E04-ECNJ4A0 Hook for Hand Exposure Switch 1 096-160
4 E04-EHLL1A0 Hand Exposure Switch Ass'y 1 096-10
E04--------------- Screw for Hook (ø-1) 1 096-10
6 E04-ECPR0A0 Restriction Plate 1 096-190
E04--------------- Power Board for 10V 1 096-1600
E04-ECPJ0D0 Front Sheet (RAL-900) 1 096-1610
- 6 -
34
65
2 1
1011
13
33
14
15
78
2019181817
21
2524
23
22
3321
3223 31
3029
2726
28
35
36
37
38
39
41
42
43
44
4546474849
50
51
52
16
9
3440
[3] SLIDING SECTION / ARM AND HEAD ASSEMBLY OF RK TYPE
- -
ID.No. PartsNo. Description QTY USA Code
1 E04-EHLL0A0 X-Ray Head Assembly (RAL-900) 1 096-1010
E04-ECPR1D0 Regular Cone (RAL-900) 1 096-1060
E04-ECPR6A0 X-Ray Exposure Sleeve 1 096-100
4 E04-ECPRB0 Lock Ring (R1-100) 1 096-1040
E04-EHLL1A0 Housing Cover Set (RAL-900) 1 096-100
6 E04-ECNR1A0 Yoke Side Cap (R1-100) 1 096-160
E04-ECPJ1A0 Yoke Inside Cover (RAL-900) 1 096-101
E04-ECPE0G0 Yoke (RAL-900) 1 096-100
9 E04-EHLL0A0 Swing Arm Assembly (RAL-900) 1
10 E04-ECLR9B0 Head Key 1 096-10
11 E04-ECLS01A0 Stopper Ring 1 096-1090
1 E04--------------- Collar Screw (SUS M4-) 1 096-1110
14 E04-ECLSA0 Collar (R1-100) 1 096-110
1 E04--------------- Stopper Screw(M4-) 1 096-110
16 E04-ECLF0B0 Swing Arm 1(RAL-900) 1
1 E04--------------- Swing Arm Pin Screw(M6-16) 1
1 E04--------------- Stopper Screw(M4-)
19 E04-ECLT4B0 Swing Arm Sleeve 1
0 E04-ECLT46C0 Swing Arm Pin 1
1 E04--------------- Brake Screw(M6-6)
E04-ECLS11B0 Brake Spring(ø-11) 1
E04-ECLS06A0 Brake Plug
4 E04-ECLS1A0 Brake Sleeve 1
E04--------------- Swing Arm Sleeve Screw(M-)
6 E04-ECLT44A0 Swing Arm Joint 1
E04-ECLF19B0 Swing Arm W/Belmont Seal(RAl-900) 1
E04--------------- Tapping Screw(ø4.-40) 4
9 E04-ECLT4A0 Thrust Washer(ø4-t) 1
0 E04-EEMU19A0 Bushing 1
1 E04-ECLS09A0 Stopper Bolt(M6-1) 1
E04-ECLS4A0 Brake Spring(ø4.-) 1
E04-EHLZA0 Cable W/Connector 1
4 E04-EHLL19A0 Column Assembly (RAL-900) 1
E04-ECLK6A0 Seat Cushion (NL-) 1
6 E04-F0 Knob(black) 1
E04-P000 Gas Cylinder 1
E04-ECLKA0 Backrest Cushion (NL-) 1
9 E04-ECLT0A0 Cushion Plate 4
40 E04-ECLK69A0 Sliding Post 1
41 E04-EALJ14A0 Column Cover 1
4 E04-EHLZA0 Guide Roller Assembly 4
4 E04-EFPR0A0 Cable Guide W/Nut 1
44 E04-EHLL1A0 Constant Tension Spring Assembly 1
4 E04-EHLL1A0 Column W/Sub Plate(RAL-900) 1
46 E04--------------- Mounting Bolt(M6-0) 4
4 E04--------------- Spring Washer(M6) 4
4 E04--------------- Washer(M6) 4
49 E04--------------- Set Screw(M-1) 4
0 E04--------------- Lag Bolt(ø-4)
1 E04-ECLTA0 Gas Cylinder Sleeve(R1-100) 1
E04-ECLKB0 Base Plate(R1-100) 1
FOR FDA USE ONLY
a. NAME OF HOUSPITAL, DOCTOR OR OFFICF WHERE INSTALLED
a. THIS REPORT IS FOR ASSEMBLY OF CERTIFIED COMPONETS WHICH ARE(Check appropriate box(es))
b. INTENDED USE(S)(Check applicble box(es))
c. THE X-RAY SYSTEM IS (Check one) d. THE MASTER CONTROL IS IN ROOM e. DATE OF ASSEMBLY
(mo.) (day) (yr.)
STATIONARY
MOBILE
a. THE MASTER CONTROL IS
f. SELECTED COMPONENTSf. (Enter number of each installed in appropriate blocks)
b. CONTROL MANUFACTURER
c. CONTROL MODEL NUMBER
a. PRINTED NAME b. SIGNATURE c. DATE
d. COMMENTS
Complete the following infomation for the certified components listed below which you installed. For beam limited device, tables and CT gantries the manufacturer and Model number in theindicated spaces. For other certified components, enter in the appropriat block how many of each you installed in this system.
b. CONTROL SERIAL NUMBER
OTHER CERTIFIED COMPONENTS
X-RAY CONTROL
HIGH VOLTAGE GENERATOR
VERTICAL CASSETTE HOLDER
TUBE HOUSING ASSEMBLY(Medical)
DENTAL TUBE HEAD
DATE MANUFACTURED
DATE MANUFACTURED
DATE MANUFACTURED
DATE MANUFACTURED
DATE MANUFACTURED
MODEL NUMBER
MODEL NUMBER
MODEL NUMBER
MODEL NUMBER
MODEL NUMBER
MANUFACTURER
MANUFACTURERBEAM
LIMIT
ING
DEVI
CETA
BLES
CTGA
NTRY
MANUFACTURER
MANUFACTURER
MANUFACTURER
CRADLE
FILM CHANGER
IMAGE INTENSIFIER
SPOT FILM DEVICE
OTHER (Specify)
c. SYSTEM MODEL NAME (CT Systems Only)
A NEW INSTALLATIONEXISTING (Certified)
EXISTING (Non-certified)
ANGIOGRAPY
TOMOGRAPHY (Other than CT)
GENERAL PURPOSE FLUOROSCOPY
GENERAL PURPOSE RADIOGRAPHY
CHEST
CHIROPRACTIC
MAMMOGRAPHY
UROLOGY
PODIATRY
DENTAL - INTRAORAL
DENTAL - CEPHALOMETRIC
HEAD - NECK (Medical)
REASSEMBLY - MIXED SYSTEM (Both certified and uncertified components)
REASSEMBLY - FULLY CHRTIFIED SYSTEM
NEW ASSEMBLY - FULLY CHRTIFIED SYSTEM
AN ADDITION TO AN EXISTING SYSTEM
REP;ACEMENT COMPONETS IN AN EXISTING SYSTEM
CT WHOLE BODY SCANNER
CT HEAD SCANNER
DIGITAL
OTHER (Specify in comments)
C - ARM FLUOROSCOPIC
RADIATION THERAPY SIMULATOR
DENTAL PANRAMIC
b. STREET ADDRESS
c. CITY d. STATE
e. ZIP CORD
a. COMPANY NAME
b. STREET ADDRESS
c. CITY
e. ZIP CORDf. TELEPHONE NUMBER
d. STATE
From Approved: OMB No. 0910-0213Expiration Date: December 31, 1992See reverse for OMB statement.
D XXXXXX
f. TELEPHONE NUMBER
1. EQUIPMENT LOCATION
3. GENERAL INFORMATION
4. COMPONENT INFORMATION (If additional space is needed for this section use another form, replacing the preprinted number with form Number and complete items 1,4, and 5 only)
5. ASSEMBLER CERTIFICATION
FORM FDA 2579(7/92) PREVIOUS EDITION IS OBSOLETE
2. ASSEMBLER INFORMATION
DEPARTMENT OF HEALTH AND HUMAN SERVICESPUBLIC HEALTH SERVICE
REPORT OF ASSEMBLYOF A DIAGNOSTIC X-RAY SYSTEM
FOOD AND DRUG ADMINISTRATION
I affirm that all certified components assembled or installed by me for which this report is being made, were adjusted and tested by me according to the instructions provided by the manufacturer(s), were of the type required by the diagnostic x-ray performance standard (1 CFR Part 100), were not modified to adversely affect performance, and were insralled in accordance with provisions of 1 CFR Part 100. I also affirm that all instruction manuals and other infomation required by 1 CFR Part 100 for this assembly have been furnished to the purchaser and within 1 days from the date of assembly, each copy of this report will be distributed as indicated at the bottom of each copy.
BELMONT EQUIPMENT, Division of Takara Belmont, USA, Inc.101 Belmont Drive Somerset, New Jersey 0 U.S.A. TEL.:() 469-000 / (00) -119 Fax.:()6-6 / (00) 0-04
TAKARA CO, CANADA LTD.06 S. Sheridan Way, Mississauga, Ont., LJM4, Can. TEL.:(90) - Fax.:(90)-60
Book No. EDAP Printed in Japan 004 MA
APPENDIXTHREE:CERTIFICATIONFORMFDA2579FROMTHEDEPARTMENTOFHEALTHANDHUMANSERVICESMUSTBEFILLEDAND MAILEDTOTHE RESPECTIVEAGENCIES FORTHIS INSTALLATIONTOBECONSIDEREDCOMPLETE.ALSOCOMPLETETHEWARRANTYCARDANDTHEASSEMBLER'SINSTALLATIONREPORTANDRETURNTOBELMONTEQUIPMENTCORP.
REFER TO THE SAMPLE FORM: