wall cap for 4-inch round duct installation...
2
Cut out this 4½” diameter circle all the way through the wall. Cut out this 6¾” diameter square only through the siding. Cut out on dotted lines. WALL CAP FOR 4-INCH ROUND DUCT INSTALLATION INSTRUCTIONS 1. Cut out template below and trace outline on wall. Avoid placement where house wiring or plumbing is located. 3. Connect METAL DUCT CONNECTOR to- gether. Snap SLOTS in DUCT into TABS on VENT COVER. 99044140A 2. Cut 4½” DIAMETER HOLE all the way through the wall. If wall is not flat: Remove any siding or other outer wall covering from inside 6¾” SQUARE - to create a flat surface. SLOTS TABS VENT COVER METAL DUCT CONNECTOR 4½” DIAMETER HOLE 6¾” SQUARE 5. Insert duct through hole in wall and fasten duct to metal duct connector. Use duct tape on all connec- tions to make them secure and air-tight. DUCT 4. Attach DUCT to fan’s DUCT CON- NECTOR. 6. Secure vent cover to wall with 4 SCREWS (included). Caulk around vent cover with a quality caulking compound. DUCT CONNECTOR CAUTION For dryer installations: Use rigid metal duct only.
Transcript of wall cap for 4-inch round duct installation...
Cut out this 4½” diameter circle
all the way through the wall.
Cut out this 6¾” diameter square
only through the siding.
Cut out on dotted lines.
wall cap for 4-inch round ductinstallation instructions
1. Cut out template below and traceoutline on wall.Avoid placementwherehousewiringorplumbingislocated.
3. Connect metAl DUCt CONNeCtOR to-gether.SnapSlOtSinDUCtintotABSonVeNtCOVeR.
99044140A
2. Cut4½”DiAmeteRhOleall thewaythroughthewall. ifwall isnotflat: Remove any siding or otherouterwallcoveringfrominside6¾”SqUARe-to create a flat surface.
SlOtS
tABS
VeNtCOVeR
metAlDUCtCONNeCtOR
4½”DiAmeteRhOle
6¾”SqUARe
5. insert duct throughhole inwall and fastenduct tometalductconnector.Useducttapeonallconnec-tionstomakethemsecureandair-tight.
DUCt
4. AttachDUCttofan’sDUCtCON-NeCtOR.
6. Secureventcovertowallwith4SCRewS(included).Caulkaroundventcoverwithaqualitycaulkingcompound.
DUCtCONNeCtOR
CAUTIONFor dryer
installations:Use rigid metal
duct only.
Cut out this 4½” diameter circle
all the way through the wall.
Cut out this 6¾” diameter square
only through the siding.
Cut out on dotted lines.
conducto de pared para conducto redondo de 4 pulg.instrucciones de instalaciÓn
1. Cortelaplantillaabajoyremonteelcontornoenlapared.evitelacolo-cacióndondeselocalizaelcableadoolaplomeríadelacasa.
3. ConecteelCONDUCtODelmetAl junto.encajeapresiónlasRANURASenconductohacia leNGÜetAS en la CUBieRtA DelReSPiRADeRO.
99044140A
2. CorteelAGUjeRODelDiámetRO4½PUlG.completamentelapared.Si la pared no es plana: quite elcualquierapartaderoolaotracubi-ertadeparedexternapordentrodelCUADRADO6¾PUlG.-paracrearuna superficie plana.
RANURAS
leNGÜetAS
CUBieRtADelReSPiRADeRO
CONDUCtODelmetAl
AGUjeRODelDiámetRO4½PUlG.
CUADRADO6¾PUlG.
5. inserte el conducto a través del agujero en paredy sujeteel conductoal conductodelmetal.Utilicela cinta del conducto en todas las conexiones delconductoparahacerlassegurasyherméticas.
4. UnaelCONDUCtOalempalmedeCONeCtADORDelCONDUCtO.
6. Seguraelcubiertadelrespiraderoalaparedcon4tornillos(incluidos).Calafateealred-edordelacubiertadelrespiraderoconuncompuestodelcalafateodelacalidad.
CONDUCtO
CONeCtADORDelCONDUCtO
PRECAUCIÓN
Para las instalaciones del secador:
Utilice el conducto
rígido del metal solamente.
![[TDB] Duct S for Europe (R410A, 50Hz, HP)...Piping Connections Liquid Pipe Ø, mm Ø, inch Gas Pipe Ø, mm Ø, inch Installation Limitation Max. Length m Max. Height m Field Wiring](https://static.fdocuments.us/doc/165x107/5e73213272baff200d7fae44/tdb-duct-s-for-europe-r410a-50hz-hp-piping-connections-liquid-pipe-.jpg)
