VTX M Series User Manual - JBLcn.jblpro.com/ProductAttachments/VTX M Series Manual V1.pdf · file...
Transcript of VTX M Series User Manual - JBLcn.jblpro.com/ProductAttachments/VTX M Series Manual V1.pdf · file...
VTX M Series User Manual
Version 1.0
Page 2
IntroductionThank you for your purchase of the JBL Professional VTX M Series!
M Series is comprised of the dual-10” VTX M20 and the dual-12” VTX M22 professional stage monitors, both featuring high-perfor-
mance differential drive woofers and the large-format D2 dual-diaphragm dual voice-coil compression driver. The option of Dual-Chan-
nel (Bi-Amp) or Single-Channel (Passive) operation comes standard, allowing the user to choose the right option for the application
with no compromise in output power or performance. Drawing on JBL’s unique history of sharing technological innovations across
product lines, the VTX M Series HF waveguide features Image Control Waveguide Technology, which gives both the VTX M20 and VTX
M22 a broad and stable 60H x 60V coverage pattern that delivers maximum gain-before-feedback. All of these premium, tour-ready
features are enclosed in modern, low profile enclosures that are lightweight, ergonomic, and show-ready for even the most high pro-
file concert or broadcast events. VTX M Series comes fully supported in JBL HiQNet Performance ManagerTM with V5 linear phase FIR
processing.
Page 3
Declaration of Conformity
We, Harman International, declare under our sole responsibility that the product, to which this declaration relates, is in conformity
with the following directives.
Brands: JBL Professional
Family Name: VTX M Series
Model Names: VTX M20, VTX M22
Copies of all Technical Data, Safety Data and EMC reports can be obtained by contacting Frank Lacelle at [email protected]
I certify that the product identified above conforms to the requirements of the Low Voltage Directive 2006/95/EC and the Waste from
Electrical and Electronic Equipment Directive 2002/96/EC RoHS. Document Link
ELECTROMAGNETIC COMPATIBILITY DIRECTIVE 2004-108-EC.pdf JBL Professional, part of the Harman International group of compa-
nies, declares that the products produced under the aforementioned brand names are designed and produced as professional audio
speakers and therefore outside of the intended scope of the European Commission Regulation (EC) 1275/2008 of 17 December 2008
implementing Directive 2005/32/EC of the European Parliament and of the Council with regard to ecodesign requirements for standby
and off mode electric power consumption of electrical and electronic household and office equipment. Document Link
Harman International expects our suppliers and business partners to be aware of their obligations under REACH and expects any sub-
stances or products within the scope of REACH to be pre-registered before December 1, 2008. The product identified above meets
REACH requirements for chemicals designated by the European Chemicals Agency (ECHA) as Substances of Very High Concern (SVHC).
Our current products are exempt from REACH pre-registration and later registration activities. We provide separate E.U. Reduction of
Hazardous Substances documentation for our RoHS compliant products. None of the products listed above have SVHC’s over the 0.1%
threshold for any chemical on the Candidate list. Document Link
The WEEE directive (2002/96/EC) places an obligation on all EU-based manufacturers and importers to take back electronic products at
the end of their useful life. JBL, through it’s agent, accepts its responsibility to finance the cost of treatment and recovery of redundant
WEEE in accordance with the specific WEEE recycling requirements. All of our products are marked with the WEEE symbol; this indi-
cates that this product must NOT be disposed of with other waste. Instead it is the user’s responsibility to dispose of their waste elec-
trical and electronic equipment by handing it over to an approved re-processor, or by returning it to JBL’s agent for reprocessing. For
more information about where you can send your waste equipment for recycling, please contact your local distributor. Document Linkt
Page 4
System Components
VTX M20Dual 10” Stage Monitor
VTX M22Dual 12” Stage Monitor
VTX S25Dual 15” Subwoofer
VTX F18SSingle 18” Subwoofer
Crown Audio I-Tech 4x3500HD4 Channel System Amplifier
Crown Audio I-Tech HD2 Channel System Amplifier
Page 5
VTX M20 SpecificationsSystem
Frequency Range (-10 dB): 55 Hz - 19.5 kHz
Coverage Pattern (-6dB) Horizontal:
Vertical:60 60
System Input Power Rating1Passive:Active:
1250 W Continuous (IEC / 100 hour)LF: 1250 W Continuous (IEC / 100 hour)HF: 100 W Continuous (IEC / 100 hour)
Maximum Peak Output²: 136dB (Preset: VTX M20 FR)
System Latency3: 3.33ms
System Processing: Crown Audio I-Tech 5000HDCrown Audio I-Tech 9000HD Crown Audio I-Tech 12000HDCrown Audio I-Tech 4x3500HD
System ImpedancePassive:Active:
4 ohmsLF: 4 ohmsHF: 8 ohms
Transducers
Low Frequency: 2 x 2261H, 254 mm (10 in) diameter, dual 76 mm (3 in) diameter voice coil, NDD ®, Direct Cooled ™
High Frequency: 1 x D2430H, D2 dual diaphragm, dual 76mm (3 in) diameter voice coil
EnclosureMonitor Angle:: 30 degrees
Construction: 18 mm, 11-ply Finnish birch plywood
Grille: Powder Coated 14 gauge hex-perforated steel with acoustically-transparent black cloth backing
Input ConnectorsPassive:
Active:
Neutrik ® Speakon ® NL-4 (4x): Selectable: Pins 1 ± or Pins 2 ±Neutrik ® Speakon ® NL-4 (4x): Pins 1 ± (LF) | Pins 2 ± (HF)
Dimensions (H x W x D): 344.9 mm x 575.0 mm x 515.3 mm(13.6 in x 22.6 in x 20.32 in)
Net Weight: 23 kg (51 lbs)
Footnotes:
1: IEC Standard: IEC shaped noise with 6dB crest factor based on Nominal impedance and a duration of 100 hours2: Peak, unweighted SPL, measured under half-space conditions at 1 meter using broadband pink noise with a 10dB crest factor and specified preset.3: Average delay of linear-phase region >200Hz
VTX M20 Dimensions
575mm | 22.64”
490.2mm | 19.30”
342.
9mm
| 1
3.50
”
JBL continually engages in research related to product improvement. Some materials, production methods and design refinements are introduced into existing products without notice as a routine expression of that philosophy. For this reason, any current JBL product may differ in some respect from its published description, but will always equal or exceed the original design specifications unless otherwise stated.
Page 6
VTX M22 Specifications
VTX M22 Dimensions
670.5mm | 26.4”
550mm | 21.8”
380.
1mm
| 1
5.0”
System
Frequency Range (-10 dB): 45 Hz - 19.5 kHz
Coverage Pattern (-6dB) Horizontal:
Vertical:60 60
System Input Power RatingPassive:Active:
1500 W Continuous (IEC / 100 hour)LF: 1500 W Continuous (IEC / 100 hour)HF: 100 W Continuous (IEC / 100 hour)
Maximum Peak Output²: 138dB (Preset: VTX M22 FR)
System Latency3: 3.33ms
System Processing: Crown Audio I-Tech 5000HDCrown Audio I-Tech 9000HD Crown Audio I-Tech 12000HDCrown Audio I-Tech 4x3500HD
System Impedance Passive:Active:
4 ohms LF: 4 ohmsHF: 8 ohms
Transducers
Low Frequency: 2 x 2262H, 304 mm (12 in) diameter, dual 76 mm (3 in) diameter voice coil, NDD ®, Direct Cooled ™
High Frequency: 1 x D2430H, D2 dual diaphragm, dual 76mm (3 in) diameter voice coil
EnclosureMonitor Angle: 30 degrees
Construction: 18 mm, 11-ply Finnish birch plywood
Grille: Powder Coated 14 gauge hex-perforated steel with acoustically-transparent black cloth backing
Input ConnectorsPassive:
Active:
Neutrik ® Speakon ® NL-4 (4x): Selectable: Pins 1 ± or Pins 2 ±Neutrik ® Speakon ® NL-4 (4x): Pins 1 ± (LF) | Pins 2 ± (HF)
Dimensions (H x W x D): 380.1 mm x 670.8 mm x 555.0 mm(15.0 in x 26.4 in x 21.8 in)
Net Weight: 27 kg (60 lbs)
Footnotes:
1: IEC Standard: IEC shaped noise with 6dB crest factor based on Nominal impedance and a duration of 100 hours2: Peak, unweighted SPL, measured under half-space conditions at 1 meter using broadband pink noise with a 10dB crest factor and specified preset3: Average delay of linear-phase region >200Hz.
JBL continually engages in research related to product improvement. Some materials, production methods and design refinements are introduced into existing products without notice as a routine expression of that philosophy. For this reason, any current JBL product may differ in some respect from its published description, but will always equal or exceed the original design specifications unless otherwise stated.
Page 7
SpeakON ConnectorsM Series products include four Neutrik SpeakON type STX series NL4 connectors (two on each side). All four NL4 connectors are wired
in parallel and can be used interchangeably depending on the stage layout and desired cabling.
M Series speaker connector plateM Series left side connectors M Series right side connectors
Speaker cables and connectorsM Series products require standard NL4 four conductor cables. The minimum recommended wire gauge for distances up to 25 meters
is 2.5mm (13 AWG) and 4.0mm (11 AWG) for longer cable runs. Choose a cable that was designed for touring applications with the
outer jacket made out of flexible and flame retardant PVC.
The Neutrik speakON STX Series connectors were specifically designed for heavy duty amplifier-loudspeaker applications like profes-
sional touring. They are durable and feature an all metal housing which makes them the recommended connectors for VTX Series
loudspeakers.
Amplifier to speaker: 25 meters Speaker to speaker: 1 meter
4 conductor NL4 cable
Page 8
Mode Selection SwitchThe VTX M20 and M22 feature a set of easily accessible selection switches.
Dual-Channel (Bi-Amp) Mode Single-Channel (Passive) ModeInput A (Channel 1)
Single-Channel (Passive) ModeInput B (Channel 2)
The first switch is a Mode Selection switch that allows for selecting between Single-Channel (Passive) and Dual-Channel (Bi-Amp)
operating modes. In Single-Channel (Passive) mode an internal crossover network is engaged that allows powering M Series monitors
with a single amplifier/DSP channel reducing the amplifier channel requirements. In Dual-Channel (Bi-Amp) mode, two amplifier/DSP
channels are used, one for the low frequency section and one for the high frequency section. Depending on the available amplifier
channels, budget, or artists requirements a user can easily switch from one mode to the other.
The second switch is a Channel Selection switch that it is only active when the Mode Selection switch is set to Single-Channel (Passive)
mode. The channel selection switch allows for selecting which set of the NL4 Pins (Pin 1± or Pin 2±) are used for powering the monitor.
Using this switch and Crown Audio I-Tech HD amplifiers, a user can select which amplifier channel is driving a set of monitors. When
using 2-channel I-Tech HD amplifiers and CH-1 NL4 output on the amplifier, when the switch is set to Input A the a monitor is driven by
Channel 1 and when the switch is set to Input B a monitor is driven by Channel 2. This configuration allows for one NL4 cable run from
the amplifier to drive up to 4x VTX M Series monitors in two independent monitor mixes. When using the 4-Channel I-Tech 4x3500HD
amplifier and the NL4 outputs, the switches can be used to select between Channels 1 or 2 for the first NL4 and Channels 3 or 4 for the
second NL4 output. This allows for powering up to 8x VTX M Series monitors with one amplifier.
A cover for the switch access panel is included and can be used to visually cover the switch panel for customers that choose not to
frequently use this feature, or for fixed installations.
Page 9
Mode Selection Switch WiringBelow is a wiring diagram showing how the Wiring Mode selection switch is connected to the M Series internal passive network and
transducers.
Page 10
Technology Highlight: Single-Channel (Passive) ModeOne of the best features of M Series is the inclusion of a new Single-Channel (Passive) mode. In this mode, up to two M20 or M22 moni-
tors can be powered with a single Crown Audio I-Tech HD amplifier channel without any performance penalties. Unlike typical passively
driven monitors, M Series splits the speaker preset responsibilities into two sections. Part of the speaker preset is processed in the
Crown I-Tech HD amplifier and part of the preset is performed internally in the speaker enclosure by a passive high-pass and a low-
pass filter. The external DSP is responsible for frequency response correction, phase response linearizion and component protection.
The combination of internal and external processing duplicates Bi-Amplified speaker preset performance while using only one ampli-
fier and DSP channel. The frequency response, phase response and maximum SPL capabilities of M Series are identical in both the
Single-Channel and Dual-Channel modes.
IIR x-overSystem HPF
IIR PEQLow Freq. Correc�on
FIRMagnitude Correc�on
FIRTime correc�on
LevelMAXProtec�on Amplifier
PassiveHPF
PassiveLPF
VTX M20 | Single-Channel (Passive)
Spacial Average: Frequency / phase response
VTX M20 | Dual-Channel (Bi-Amp)
Spacial Average: Frequency / phase response
Crown I-Tech HD System Controller
Amplifier Processing Speaker Processing
20 100 1000 10000 20000Frequency (Hz)
-30
-20
-10
0
10 180
90
0
-90
-180
SPL
(dB)
20 100 1000 10000 20000Frequency (Hz)
-30
-20
-10
0
10 180
90
0
-90
-180
SPL
(dB)
Page 11
Amplification and ProcessingLike all other VTX products, M Series is powered exclusively by Crown iTech HD power amplifiers, providing optimum performance and
consistency across the world. Standard V5 level presets are available for Single-Channel (Passive) and Dual-Channel (Bi-Amp) modes.
The most up to date presets are distributed with the latest version of JBL’s Performance Manager control software and are also avail-
able as standalone downloads at www.jblpro.com
The Crown I-Tech HD series amplifiers feature BSS Audio OMNIDRIVEHD™ processing for each amplifier channel, including the ac-
claimed LevelMAX™ Limiter Suite and support for complex phase FIR filters as used in the latest JBL V5 loudspeaker presets. All M
Series processing is done using I-Tech HD internal processing and no other external DSP is required. Crown amplifiers include a user
adjustable input section that can be used for additional equalization and adjustments if needed.
The I-Tech 4x3500HD amplifier features four independent inputs (Analog, AES3 or CobraNet™) and are fully routable to any one of the
4 outputs. The four inputs allow the I-Tech 4x3500HD to drive up to four independent monitor mixes (in Single-Channel mode) reduc-
ing the number of amplifiers required.
I-TECH 4x3500 | 2300W
REG
. U.S
. PAT
. OFF
. 5,6
57,2
19
6,50
4,34
8 6
,909
,321
7,28
3,37
9 7
,557
,622
7,9
19,9
98 7
,778
,324
7,5
21,9
36
CLA
SS 2
OU
TPU
T W
IRIN
G
Crown Audio I-Tech 4x3500HD Rear Panel
Crown Audio I-Tech HD Rear Panel
Crown Audio I-Tech 4x3500HD Crown Audio I-Tech HD
Page 12
Crown Audio I-Tech HD Output WiringThe 4-channel Crown Audio I-Tech 4x3500HD includes 2 x NL4 connectors and has Channels 1 & 2 bi-wired to the left NL4 and Channels
3 & 4 bi-wired to the right NL4. An NL8 output connector is also available that contains all 4 amplifier channels on Pins 1 ± through 4 ±
respectively. Output connector wiring configurations are shown below:
Both NL4 connectors can be used to power M Series products. For this specific application (stage monitoring) the NL8 connector is typ-
ically left unused. Since the NL4 connectors contain two amplifier channels, simple four-conductor NL4 cables can be used to connect
the amplifiers to the speakers.
A similar wiring scheme applies to the 2 Channel Crown I-Tech HD amplifiers however it is important to note that only the Channel 1
NL4 output is bi-wired.
NL4 WiringPin 1 ± Channel 1 ±Pin 2 ± Channel 2 ±
NL4 WiringPin 1 ± Channel 3 ±Pin 2 ± Channel 4 ±
NL8 WiringPin 1 ± Channel 1 ±Pin 2 ± Channel 2 ±Pin 3 ± Channel 3 ±Pin 4 ± Channel 4 ±
NL4 WiringPin 1 ± Channel 1 ±Pin 2 ± Channel 2 ±
NL4 WiringPin 1 ± Channel 2 ±Pin 2 ± Not Connected
Page 13
Crown Audio I-Tech 4x3500HD ConfigurationsDual-Channel (Bi-Amp) Mode
The Crown Audio I-Tech 4x3500HD amplifier can power up to four M20 or M22 monitors in Dual-Channel (Bi-Amp) mode. In this
configuration, channels 1 & 3 power the low frequency section and channels 2 & 4 power the high frequency section. Up to two inde-
pendent monitor mixes can be achieved using inputs 1 and 3 of the amplifier. All M Series Mode Selection switches should be set to
Dual-Channel (Bi-Amp) mode.
I-Tech 4x3500HD
Monitor Mix 1
Monitor Mix 1
Selection Switches
Selection Switches
CH 1/2 CH 1/2
CH 3/4 CH 3/4
Page 14
Single-Channel (Passive) Mode
The Crown Audio I-Tech 4x3500HD amplifier can power up to eight M20 or M22 monitors in Single-Channel (Passive) mode. In this
configuration each channel is powering a pair of monitors. Up to four independent monitor mixes can be driven using inputs 1 - 4 of
the I-Tech HD amplifier. In this configuration, all Mode Section switches should be set to Single-Channel (Passive) mode and the Chan-
nel-Selection switches as illustrated below.
I-Tech 4x3500HD
Monitor Mix 3
Monitor Mix 4
Monitor Mix 1
Monitor Mix 2
Selection Switches
Selection Switches
Selection Switches
Selection Switches
CH 1 CH 1
CH 2 CH 2
CH 3 CH 3
CH 4 CH 4
Page 15
Single-Channel (Passive) Mode - Stereo Mix
Stereo monitor mixes can be set using Crown Audio I-Tech 4x3500HD amplifiers and the channel selection switches. In this configura-
tion, each amplifier channel is driving a single M Series monitor. The Mode Selection switches should be set to Single-Channel and the
Channel Selection switches should be set as illustrated below. This will create two independent stereo monitor mixes.
I-Tech 4x3500HD
Monitor Mix 2 - Left
CH 3 CH 4
Monitor Mix 2 - Right
Monitor Mix 1 - Left Monitor Mix 1 - Right
CH 1 CH 2
Page 16
Crown Audio I-Tech 9000HD & 12000 HD ConfigurationsDual-Channel (Bi-Amp) Mode
Crown Audio I-Tech 9000HD and 12000HD amplifiers can power up to two M20 or M22 monitors in Dual-Channel (Bi-Amp) mode. In
this configuration channel 1 is powering the low frequency section and channel 2 powers the high frequency section. A single monitor
mix can be achieved in the configuration using input 1 of the amplifier. All M Series Mode Selection switches should be set the Du-
al-Channel (Bi-Amp) mode and the bi-wired CH-1 NL4 output connector should be used.
Single-Channel (Passive) Mode
Crown Audio I-Tech 9000HD and 12000HD amplifiers can power up to four M20 or M22 monitors in Single-Channel (Passive) mode. In
this configuration each channel is powering a pair of monitors and up to two independent monitor mixes can be achieved using inputs
1 and 2 of the I-Tech HD amplifier. All mode selection switches should be set to Single-Channel (Passive) and the Channel-Selection
switches as illustrated below.
I-Tech 9000HD / 12000HD
Monitor Mix 1 Selection Switches
I-Tech 9000HD / 12000HD
Monitor Mix 1 Selection Switches
Monitor Mix 2 Selection Switches
CH 1/2 CH 1/2
CH 1 CH 1
CH 2 CH 2
Page 17
Crown Audio I-Tech 5000HD ConfigurationsDual-Channel (Bi-Amp) Mode
Crown Audio I-Tech 5000HD amplifiers can power up to one M20 or M22 monitor in Dual-Channel (Bi-Amp) mode. In this configu-
ration, channel 1 is powering the low frequency section and channel 2 powers the high frequency section. A single monitor mix can
be achieved in this configuration using input 1 of the amplifier. All M Series Mode Selection switches should be set the Dual-Channel
(Bi-Amp) mode.
Single-Channel (Passive) Mode - Stereo Mix
The Crown Audio I-Tech 5000HD amplifier can power up to two M20 or M22 monitors in Single-Channel (Passive) mode. In this con-
figuration each channel is powering a single monitor. Up to two independent monitor mixes can be achieved using inputs 1 and 2 of
the I-Tech HD amplifiers. In this configuration, all Mode Section switches should be set to Single-Channel (Passive) and the Channel-Se-
lection switches as illustrated below.
I-Tech 5000HD
Monitor Mix 1 Selection Switches
I-Tech 5000HD
Monitor Mix 1 Monitor Mix 2
Selection Switches Selection Switches
CH 1 / CH-2
CH-1 CH-2
Page 18
Using M SeriesM Series V5 presets are optimized to generate a flat frequency response down to 150Hz with a small LF shelving response increase
below 150Hz for added LF impact. Two preset variations are available for each product and configuration modes:
Full-Range (FR): Full-Range (FR) presets allow M Series products to operate down to a safe low frequency limit that each monitor can
reproduce. This set of presets can be used when a full range performance is desired (i.e. drum fill or bass monitor).
With Subwoofers (80): The 80 preset introduces a high-pass filter at 80Hz and can be used when M Series is combined with supported
VTX Subwoofers (VTX F18S or the VTX S25). In this case, M Series is responsible for the spectrum above 80Hz and the added subwoofer
contributes to frequencies below 80Hz and down to 30Hz. The 80 presets can also be used in situations where no subwoofers are pres-
ent but reduced LF extension/energy is required such as vocal monitoring or when it is desirable to maximize A-weighted SPL output.
Supported VTX Series Subwoofers When added low frequency extension is needed, M Series monitors can be used in conjunction with supported VTX Series subwoofers.
Preset support is included for the dual 15” VTX S25 subwoofer enclosure and the single 18” VTX F18S. Preset time alignment is opti-
mized for M Series products to be placed on top of the subwoofer enclosure as shown in the examples below. The orientation of the
M Series monitors can be selected depending on the required throw distance.
Each product (M20 and M22) can be used with either one of the subwoofer enclosures (see preset summary sheets for more informa-
tion). Multiple subwoofers enclosures can be used to achieve the desired low to mid-hi frequency contour and target MAX SPL.
Short Throw Long Throw
Page 19
VTX M Series with Subwoofers
The combination of M Series and subwoofers can also be used in stereo pairs. Applications for these configurations include stereo DJ
monitoring systems, stereo drum monitoring and side fill systems for small stages.
VTX M20 with VTX F18S VTX M22 with VTX S25
Page 20
Using Multiple MonitorsM Series factory presets are optimized to generate a flat frequency response for single cabinet operation. When more than one M
Series monitor is used, there will be an increase in low-frequency energy and in general, when combining M Series products in moni-
tor arrays, high-frequency energy increases by 3dB every time the box quantity is doubled, while the low-frequency energy increases
by 6dB. This is due to the directivity characteristics of relatively small loudspeaker systems. Products of this size and type tend to be
directional at higher frequencies and relatively omni-directional at lower frequencies which affects the rate of coupling for the differ-
ent parts of the frequency spectrum. In some cases this extra increase of low-frequency energy is desired and this is the reason why
multiple monitors are used. In other cases a flatter frequency response is desired.
When a flatter frequency response is the target, a shelving filter can be used to compensate for the extra low frequency coupling. The
low frequency shelving filter can be implemented using the Input / User EQ section of Crown I-Tech HD amplifiers or an external pro-
cessor or console prior to the I-Tech HD amplifier. The type and corner frequency of this filter remains the same for all configurations
and M Series models and filter gain can be adjusted to achieve the desired frequency response.
When using two M Series monitors placed closely together, a 6dB/Oct shelving filter can be used to compensate for the low frequency
build up. The gain of this filter can range from 0dB to -3dB depending on the desired frequency target.
20 100 1000 10000 20000Frequency (Hz)
-25
-15
-5
5
15
SPL
(dB)
Low Frequency Coupling Filter
6dB/Oct Shelving Filter | Freq: 500Hz | Gain: 0 - -3dB
Page 21
Using Multiple Monitors
20 100 1000 10000 20000Frequency (Hz)
-25
-15
-5
5
15
SPL
(dB)
When using four monitors closely placed together, the same 6dB/Oct 500Hz filter can be used with increased attenuation. In this con-
figuration the gain of the filter can take values from 0dB to -6dB depending on the desired frequency target.
Low Frequency Coupling Filter
6dB/Oct Shelving Filter | Freq: 500Hz | Gain: 0 - -6dB
Page 22
Crown Audio I-Tech 4x3500HD Presets
CH 1 CH 2 CH 3 CH 4
Single-Channel (Passive) FR
VTX M20 FR 2 VTX M20 Full Range - Single-Channel (Passive) mode M20 FR M20 FR M20 FR M20 FR
VTX M22 FR 3 VTX M22 Full Range - Single-Channel (Passive) mode M22 FR M22 FR M22 FR M22 FR
VTX M20 - M22 FR 4 VTX M20 & M22 Full Range - Single-Channel (Passive) mode M20 FR M20 FR M22 FR M22 FR
Single-Channel (Passive) 80Hz
VTX M20 80 6 VTX M20 80Hz HPF - Single-Channel (Passive) mode M20 80 M20 80 M20 80 M20 80
VTX M22 80 7 VTX M22 80Hz HPF - Single-Channel (Passive) mode M22 80 M22 80 M22 80 M22 80
VTX M20 - M22 80 8 VTX M20 & M22 80Hz HPF - Single-Channel (Passive) mode M20 80 M20 80 M22 80 M22 80
Dual-Channel (Bi-Amp) FR
VTX M20 2W FR 10 VTX M20 Full Range - Dual-Channel (Bi-Amp) mode M20 2W LF M20 2W HF M20 2W LF M20 2W HF
VTX M22 2W FR 11 VTX M22 Full Range - Dual-Channel (Bi-Amp) mode M22 2W LF M22 2W HF M22 2W LF M22 2W HF
VTX M20 - M22 2W FR 12 VTX M20 & M22 Full Range - Dual-Channel (Bi-Amp) mode M20 2W LF M20 2W LF M22 2W LF M22 2W HF
Dual-Channel (Bi-Amp) 80Hz
VTX M20 2W 80 14 VTX M20 80Hz HPF - Dual-Channel (Bi-Amp) mode M20 2W LF 80 M20 2W HF 80 M20 2W LF 80 M20 2W HF 80
VTX M22 2W 80 15 VTX M22 80Hz HPF - Dual-Channel (Bi-Amp) mode M22 2W LF 80 M22 2W HF 80 M22 2W LF 80 M22 2W HF 80
VTX M20 - M22 2W 80 16 VTX M20 & M22 80Hz HPF - Dual-Channel (Bi-Amp) mode M20 2W LF 80 M20 2W LF 80 M22 2W LF 80 M22 2W HF 80
Subwoofer Presets 80Hz
VTX F18S 80 18 VTX F18S 80Hz LPF - use with M Series 80 presets F18S 80 F18S 80 F18S 80 F18S 80
VTX S25 80 19 VTX S25 80Hz LPF - use with M Series 80 presets S25 80 S25 80 S25 80 S25 80
Device File: VTX M Series V5 R1.I-TECH4x3500HD.Device
Arbitrary preset combinations can be created using JBL's HiQNet Performance ManagerTM control software
Page 23
Crown Audio I-Tech HD Series Presets
Device File: VTX M Series V5 R1.I-TECHHD.Device
CH 1 CH 2
Single-Channel (Passive) FR
VTX M20 FR 2 VTX M20 Full Range - Single-Channel (Passive) mode M20 FR M20 FR
VTX M22 FR 3 VTX M22 Full Range - Single-Channel (Passive) mode M22 FR M22 FR
VTX M20 - M22 FR 4 VTX M20 & M22 Full Range - Single-Channel (Passive) mode M20 FR M22 FR
Single-Channel (Passive) 80Hz
VTX M20 80 6 VTX M20 80Hz HPF - Single-Channel (Passive) mode M20 80 M20 80
VTX M22 80 7 VTX M22 80Hz HPF - Single-Channel (Passive) mode M22 80 M22 80
VTX M20 - M22 80 8 VTX M20 & M22 80Hz HPF - Single-Channel (Passive) mode M20 80 M22 80
Dual-Channel (Bi-Amp) FR
VTX M20 2W FR 10 VTX M20 Full Range - Dual-Channel (Bi-Amp) mode M20 2W LF M20 2W HF
VTX M22 2W FR 11 VTX M22 Full Range - Dual-Channel (Bi-Amp) mode M22 2W LF M22 2W HF
Dual-Channel (Bi-Amp) 80Hz
VTX M20 2W 80 13 VTX M20 80Hz HPF - Dual-Channel (Bi-Amp) mode M20 2W LF 80 M20 2W HF 80
VTX M22 2W 80 14 VTX M22 80Hz HPF - Dual-Channel (Bi-Amp) mode M22 2W LF 80 M22 2W HF 80
Subwoofer Presets 80Hz
VTX F18S 80 16 VTX F18S 80Hz LPF - use with M Series 80 presets F18S 80 F18S 80
VTX S25 80 17 VTX S25 80Hz LPF - use with M Series 80 presets S25 80 S25 80
Arbitrary preset combinations can be created using JBL's HiQNet Performance ManagerTM control software
Page 24
Mailing Address:JBL Professional8500 Balboa Blvd.Northridge, CA 91329
Shipping Address:JBL Professional8500 Balboa Blvd., Dock 15Northridge, CA 91329(Do not return product to this address without first obtaining prior authorization from JBL)
Customer Service:Monday through Friday8:00am -5:00pmPacific Coast Time in the U.S.A.(800) 8JBLPRO (800.852.5776)www.JBLservice.com
On The World Wide Web:www.JBLPro.com
Professional Contacts, Outside the USA:Contact the JBL Professional Distributor in your area.A complete list of JBL Professional international distributors is provided at our U.S.A. website: www.jblpro.com