VTC-C2BTS1 - vitekcctv.comvitekcctv.com/Manuals/VTC-C2BTS1_Manual.pdf · VTC-C2BTS1 2.1MP Premium...
Transcript of VTC-C2BTS1 - vitekcctv.comvitekcctv.com/Manuals/VTC-C2BTS1_Manual.pdf · VTC-C2BTS1 2.1MP Premium...
FEATURES:
• 1/2.7” Progressive Scan CMOS Sensor
• 2.1 MegaPixel with Full 1080p TVI Output
• Small scale design to fit in 5” dome enclosures such as the Pelco® DF5 Housing
• Sensitivity of 0.08 Lux
• 2D-DNR Digital Noise Reduction
• True Day/Night by ICR (Infrared Cut Removal)
• Built-in Motion Detection with a 24x16 Grid
• Privacy Mask function with programmable mask areas
• 12VDC / 24VAC Dual Voltage Operation
• Lenses Sold Separately
VTC-C2BTS12.1MP Premium TVI Compact
Box CameraVIT
EK
VIT
EK
Safety Precaution
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.To prevent electric shocks and risk of fire hazards, do NOT use other than specific power source.
Warning : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Mains power quality should be that of a typical commercial environment. If the user of the model requires continued operation during power mains interruptions, it is recommended that the model be powered from an uninterruptible power supply (UPS) or a battery.
The symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be ofsufficient magnitude to constitute a risk of electric shock to persons.
2 3
Safety Precaution
NOTICE
The image used in this instruction manual are processed to help comprehension and may differ from actual video of the camera.Avoid installing areas where has shock or vibration which results in the problems.Pay attention to safety when laying the connection cable and observe that the cableis not subjected to heavy loads, kinks or damage and no moisture can get in.Never open the device such as boards.The warranty becomes void if repairs are undertaken by unauthorized persons.Maintenance and repair have to be carried out only by authorized service centers.Use only a mild detergent to clean the housing.The camera should never be operated beyond the technical specifications. This can lead to destruction.The camera should never be operated in water.
3
Contents
Safety Precautionp.02~03
Contentsp.04
Featuresp.05
Compositionp.06
Dimensionsp.06
Part Namesp.07
Installation Instructionsp.08~09
Operating Instructionsp.10~19
Specificationsp.20
4 5
Features
Key Features
• 1/2.7” CMOS Sensor• Full-HD 2Mega pixel HD-TVI CAMERA, 1920x1080(30p)• TVI Video Transmission Distance over Coax.; 500M (RG59, 75Ω) *depending on cable condition and characteristics• Automatically removable IR Cut filter by Dual filter switcher• CS mount supported (Option: C-mount adaptor)• Sensitivity of 0.08 Lux (AGC 3)• Improved noise reduction 2DNR• LSC (Lens Shading Compensation)• Motion detection, Privacy mask, BLC/HLC, Flickerless, H/V/HV Flip• UTC control through HD-TVI DVR (Pelco-C)• Back focus Flange• Built-in OSD MENU• Reverse polarity protection circuit• Isolated power supply against ground loop problem• Power: AC24V/DC12V
5
L- Wrench: 1.5mm (1pc)
Dust Protection Cap (1pc)
Operating Instruction
Compact Box Camera
1.73
”2.
09”
1.89”Ø1.81”
2.38”2.89”
Dimensions
Composition
6 7
Part Names
L-Wrench
DustProtection Cap
No.1234
DC IrisDamp(-)Damp(+)Drive(+)
GND
Flange Lock screw
Front Case
Rear Case
Back focusadjusting Flange
Mount Holes(Top / Bottom)
REAR VIEW
Lens Connectorfor Auto Iris lenses
① Video out connector(BNC)② Power input terminal③ OSD Control Joy stick④ DC Auto Iris Lens connector④
③
①
②
PIN 1PIN 3
PIN 2PIN 4
7
Installation Instructions
CAUTION
Installation Instructions• Make sure the power is removed before installation
1. Remove the dust protection cap from the lens mount.2. Screw the lens onto the camera firmly.3. Plug the lens plug into the lens connector on the rear of camera case.4. Mount the camera to the wall or ceiling with a corresponding mounting bracket through the camera mount holes (1/4” thread insert) on its top or bottom• Follow this order for applying power. First connect the low voltage cable (DC12V or AC24V), then plug the AC adapter into AC outlet to avoid damage from the surge voltage with no load.
• Care should be taken the cable is NOT damaged, kinked or exposed in hazardous areas.• Do not expose the camera lens directly to a strong light source such as the sun or spot light.
Setting the back focus adjustmentFor easier and better adjustment, this camera provides FOCUS ADJUST menuwhich helps with focusing the camera.When enabling FOCUS ASSIST menu, follow the procedure to get the best backfocus adjustment.
1. Set the lens for the zoom position to WIDE and the focus position to INFINITE(∞).2. Point at an object 30' away3. Adjust ’Back focus adjusting Flange’ until the optimum focus is achieved.4. Set the lens for zoom position to TELE and adjust the lens focus for best focus.5. Set the lens for zoom position to WIDE again, check if the focus adjustment is the best. If not, re-adjust ‘Back focus Flange’ slightly.6. After setting, tighten the ‘Flange lock screw’ with L-wrench supplied.
Start upWhen the camera is powered properly, it starts up with initializing the internal parameters.
8 9
Installation Instructions
Using OSD ControllerSetup menu can be accessed and controlled by OSD control joy stick on the rear of the camera unit.Five commands are available with the joy stick.The design of rear panel could be different according to the camera models.
Description of the joystick operation
1) SET Key () : Access to the menu or enter the setting. To enter the main menu, press the Set Key down for about 1.5sec2) UP/DOWN Key (/) : Choose the desired sub-menu and to move the cursor up or down.3) LEFT/RIGHT Key (/) : Set up the value of the selected menu. Use to adjust the desired menu selection and to move the cursor left or right.
9
Operating Instructions
OSD menu Startup
• EXIT : Enters ‘EXIT’ menu.• RETURN : Returns to the previous menu.
Press the ‘OSD menu SET key’ down to access the setup menu mode.
MAIN MENU
> 1. VIDEO OUT 2. DAY / NIGHT 3. AWB 4. AE 5. SPECIAL 6. EFFECT 7. SYSTEM 8. EXIT
OSD menu TableMAIN MENU SUB MENU CONFIGURATION
VIDEO OUT
DAY/NIGHT
AWB
FRAME RATERETURNMODE
MODE
30 / 25
1~631~631~60 SEC
COLORB&W
AUTO
USER
AUTOEXT
D TO NN TO DDELAY TIMERETURN
IN/OUT DOORRETURNRED GAINGREEN GAIN
IN, OUT
1~2551~255
10 11
Operating Instructions
AWB
AE
SPECIAL
MODE
PUSH8000K6000K4200K3200KHOLD
MODEBRIGHTSHUTTER
FLICKERBLCAGCLSCRETURN
USER
R-GAINB-GAINRETURN
PRIVACY ZONE
MOTION
HLC
RETURN
BLUE GAINRETURN
AREA SEL.MASK PAT.SXEXSYEYRETURN
AREA1, AREA 2OFF, BLACK, GRAY, WHITE0~2400~2400~1350~135
OFF, ON0~255OFF, TRACE, ICON1~10 SEC
DC, ESC, HOLD0~255AUTO, 1/25, 1/30, 1/50, 1/60, 1/100, 1/120, 1/250, 1/500, 1/1000, 1/3000, 1/10000
1~255
1~2551~255
OFF, 50Hz, 60Hz0~161~5ON, OFF
MOTIONSENSITI.ALARMHOLD TIMERETURNHLCMASK VALUETHRESHOLDRETURN
OFF, ON0~2550~255
AREA SET
11
Operating Instructions
MAIN MENU> 1. VIDEO OUT 2. DAY / NIGHT 3. AWB 4. AE 5. SPECIAL 6. EFFECT 7. SYSTEM 8. EXIT
VIDEO OUT> 1. FRAME RATE : 30 2. RETURN
OSD menu Setup
1. VIDEO OUT
EFFECT
SYSTEM
EXIT
COLOR GAINCOLOR HUESHARPNESSCONTRASTBRIGHT OFF.MIRRORFLIPRETURNCAMERA IDID DISPNAME DISPLANGUAGEFACTORY INITRETURNSAVE/EXITEXITRETURN
0~2550~710~2550~255-128~127OFF, ONOFF,ON
0~255OFF, ONOFF,ONENG, CHINESEOFF, ON
Selects HDTV standards for video output switches to FRAME RATE 30(NTSC)or 25(PAL) accordingly.
12 13
Operating Instructions
DAY/NIGHT is used to control the setting during day-time and night-time operation. Select the mode according to the light condition and the cameratypes.
2-1-3. AUTOUsed when DAY or NIGHT is determined by light level through the lens and DAY from/to NIGHT is switched automatically by the scene brightness.
Sets the threshold level switching from/to DAY(color) or NIGHT(B/W).Setting at a low level makes the camera enter NIGHT at a lower light level.High level makes the camera exit NIGHT at a higher light level.
2-1-2. B/WThe camera is always in B/W mode.Forcibly removes IR cut filter and switches to B/W regardless of light level.
2-1-1. COLOR
2-1. MODE
The camera is always in COLOR mode.Forcibly DAY/NIGHT is disabled and outputs color video.
2-2. D TO N : 1~63
DAY / NIGHT> 1. MODE 2. D TO N 3. N TO D 4. DELAY TIME 5. RETURN
: [EXT]: 55: 35: 3SEC
2. DAY / NIGHT
2-1-4. EXTDAY or NIGHT is determined by the built-in light photo sensor.Camera with IR LED must be set to EXT.
13
Operating Instructions
Automatically tracks the changes of color temperature and continuously adjusts the white balance.
> OUT : Optimized for outdoor sunlight applications and easily compensates AWB for high color temperature such as sunlight.
> IN : Optimized for Indoor installation and easily compensates AWB for low color temperature such as incandescent lights.
Sets the delay time when the camera switches from/to DAY(color)or NIGHT(B/W).
3-1-1. AUTO : IN/OUTDOOR3-1. MODE
The camera is automatically set to INDOOR or OUTDOOR environments.
Sets the gap level switching from/to DAY(color) or NIGHT(B/W).2-3. N TO D : 1~63
2-4. DELAY TIME : 1~60SEC
AWB> 1. MODE 2. R-G GAIN 3. B-G GAIN 4. RETURN
: [AUTO]: 128: 128
AWB > AUTO MODE> 1. IIN/OUT DOOR 2. RETURN
: OUT
3. AWB
White balance is fixed to the settings by Red, Green and Blue_GAIN. This mode can be used only when the color temperature does not vary.
3-1-2. USER
3-1-3. PUSH : White balance is performed only whenever ‘PUSH’ is selected.3-1-4. 8000K : Set the white balance range by 8,000°K.
14 15
Operating Instructions
Lens can be selected either DC or MANUAL lens.Lens MUST be set to DC for the best image when DC iris lens is installed
White balance is fixed to the settings of Red-Green GAIN.
White balance is fixed to the settings of Blue-Green GAIN.
3-2. R-G GAIN : 1~255
3-3. B-G GAIN : 1~255
4-1. MODE
3-1-5. 6000K : Set the white balance range by 6,000°K.
3-1-6. 4200K : Set the white balance range by 4,200°K.3-1-7. 3200K : Set the white balance range by 3,200°K.3-1-8. HOLD : Fixed white balnce.
4-1-1. DC :
4-1-2. ESC : Set the Electric Shutter Control
4-1-3. HOLD : Fixed exposure.
AE> 1. MODE 2. BRIGHT 3. SHUTTER 4. FLICKER 5. BLC 6. AGC 7. LSC 8. RETURN
: DC: 128: AUTO: OFF: 0: 5: OFF
4. AE
: Selects lens mode according to installation conditions.
Increases or decreases the brightness of the picture. This is different from that of DC iris lens and simply increases or decreasesthe digital gain of video. Do not increase this too much, the dynamic rangefor the bright areas will decrease.
4-2. BRIGHTNESS : 0~255
AE(Auto Exposure) menu provides the parameters which control the light leveland enhance the dynamic range of video.
15
Operating Instructions
4-5. BLC : 0~16BLC(Back Light Compensation) is used to brighten an image in the fore-ground with a bright area behind it such as sunlight, limiting the affectof silhouette. Set the BLC level from 0 to 16.
Sets the PRIVACY Zone, AREA1 or 2 are available and each area is pro-grammable in size, color and position.
PRIVACY ZONE> 1. AREA SEL. 2. MASK PAT. 3. SX 4. EX 5. SY 6. EY 7. RETURN
SPECIAL> 1. PRIVACY ZONE 2. MOTION 3. HLC 4. RETURN
5. SPECIAL
5-1. PRIVACY ZONE5-1-1. AREA SEL. : Area1, Area2
4-3-1. AUTO: Optimizes the video level by controlling the iris and the shutter speed automatically.4-3-2. 1/30(1/25), 1/60(1/50), 1/120(1/100), ~ 1/10000: Shutter can be set to fix.
Reduces the flicker in video when NTSC/PAL mode is used in 50Hz / 60Hz fluorescent lighting respectively.
Select Shutter speed, AUTO or manual.4-3. SHUTTER
4-4. FLICKER
AGC(Auto Gain Control) can be set from 1 to 5 levels.4-6. AGC : 1~5
LSC(Lens Shade Compensation) is used to caculate the compensation datafor lens shading. Convex shape of the lens causes the light to enter the camera unevenly and typically makes the center of the screen brighter than the rest. It is used to compensate for this undesirable effect and make the screen more even.
4-7. LSC
: AREA1: WHITE: 16: 32: 16: 32
16 17
Operating Instructions
If set to ON, motion is displayed on the monitor by means of digital effect.
Sets the detection sensitivity for motion. High value increases the sensitivityto detect small motion easily. Too low will cause erratic detection bytree leaves or light level changes.
MOTION> 1. MOTION 2. SENSITI. 3. ALARM 4. HOLD TIME 5. RETURN
SPECIAL 1. PRIVACY ZONE> 2. MOTION 3. HLC 4. RETURN
5-2-1. MOTION : OFF, ON
5-3-1. HLC : OFF, ON
5-2-2. SENSITI. : 0~255
Set to OFF, TRACE, ICON for motion alarm display.5-2-3. ALARM : OFF, TRACE, ICON
Sets the interval time from the starting of motion operation until being readyfor the next motion operation.
5-2-4. HOLD TIME : 1~10 SEC
5-2. MOTION
5-3. HLC
Selects the mask color pattern Area 1 or 25-1-2. MASK PAT. : Off, Black, Gray, White
5-1-3. SX, EX. : Set the X-position or size for the selected arear (Start-X, End-X)5-1-4. SY, EY. : Set the Y-position or size for the selected arear (Start-Y, End-Y)
: OFF: 32: OFF: 1SEC
HLC (High Light Cut out) is used to black out bright areas, in order to enable a clear visual image of objects.
Set to ON, select window for HLC.
5-3-2. MASK VALUE : 0~255Set the transparency rate for the HLC mask.
17
Operating Instructions
HLC > AREA SET> 1. AREA SET
2. RETURN
X X <O> XX X X XX X X XX X X X
HLC> 1. HLC 2. MASK VALUE 3. THRESHOLD 4. RETURN
6-1. COLOR GAIN : 0~255
EFFECT> 1. COLOR GAIN 2. COLOR HUE 3. SHARPNESS 4. CONTRAST 5. BRIGHT OFF. 6. MIRROR 7. FLIP 8. RETURN
: 60: 0: 10: 128: 0: ON: ON
6. EFFECT
: ON: 32: 250
Defines the threshold level for HLC. Lower value masks more.5-3-3. THRESHOLD : 0~255
Increases or decreases the color saturation.
6-2. COLOR HUE : 0~71
Increases or decreases the sharpness of the picture.Too much sharpness can make image harsh and show more noise as wellas line flicker at the edge of objects in the picture.
Adjusts hue of the picture.
6-3. SHARPNESS : 0~255
6-4. CONTRAST : 0~255Adjusts the strength of the image contrast. If set to too high, the dark areamay loss detail and the bright area may saturate.
18 19
Operating Instructions6-5. BRIGHT OFF : -128~127
Controls the brightness of the image, to high of setting will cause more noisein the picture
6-6. MIRROR : OFF, ONMirrors the video signals vertically.
6-7. FLIP : OFF, ON
7-1. CAMERA ID : 0~255
7-2. ID DISP. : OFF, ON
7-3. NAME DISP. : Not supported.
Flips the video signals horizontally.
SYSTEM> 1. CAMERA ID 2. ID DISP. 3. NAME DISP. 4. LANGUAGE 5. FACTORY INIT. 6. RETURN
: 0: OFF: OFF: ENG: OFF
7. SYSTEM
Set number for the Camera ID.
8-1. SAVE / EXIT : Save all the settings and exit the setup menu.8-2. EXIT : Exit the setup menu without saving.
8. EXIT
Set ON/OFF for enabling/disabling of camera ID.
7-4. LANGUAGESelect camera OSD menu language English or Chinese.
7-5. FACTORY INITIf set to ON, all the camera setting are restored to the factory defaults.
19
Detailed SpecificationsImaging Sensor
Video Output
Resolution
Effective Pixels
S/N Ratio
Sensitivity
Lens Type
DAY / NIGHT
White Balance
DNR
Advanced OSD Features
Remote Control
Operating Conditions
Input Voltage
Power Consumption (12VDC)
Power Consumption (24VAC)
Weight
Dimensions (W x H x L)
1/2.7” Progressive Scan CMOS Sensor
HD-TVI by BNC
2.1 MegaPixel (1080p)
1920(H) x 1080(V) x 30p
More than 52dB with AGC Off at 50 IRE
0.08 Lux (AGC 3)
CS Mount Lens Support
Mechanical IR Cut Filter (True Day/Night)
Auto / User / Push / Hold
2D-DNR
BLC/HLC, Motion detection, Privacy mask, Flickerless, LSC (Lens Shading
Compensation), Flip
UTC by HD-TVI DVR (Pelco-C)
14°~122°F (-10°~ +50°C) < 80% RH
12VDC / 24VAC (Dual Voltage)
185mA @ 12V (2.2W)
100mA
5.43 Oz. (154g)
1.89” x 2.09” x 2.89” (48 x 53 x 73.5mm)
20 21
VT-SHP916SpireHD 16 Channel Real Time Tribrid TVI / AHD / 960H Digital Video Recorder
• Supports High Resolution TVI, AHD, and 960H Cameras• 16 Video Inputs with 1 HDMI, 2 Spot Monitor Outputs, and 1 VGA output • H.264 Compression• Real Time Live Display & Recording• Supports both Dynamic and Static IP Addresses• 16 Audio Inputs / 1 Audio Outputs• 18 Alarm Inputs (16 +1 Panic & 1 Reset) 8 Outputs with 8 Relays• Supports 6TB Hard Drives• Supports 5 internal Hard Drives for up to 30TB of internal Storage (5 x 6TB HDD)• Supports RAID Levels 1 & 5• Dual Ethernet Ports• Remote Viewing over the LAN/WAN via Web Browser• Applications for iPhone, iPad, iTouch and Android Devices• Mac OSX Client & PC CMS Central Management Software Included• Panorama (Thumbnail) & “Quick Search” Functions• Convenient Network Settings Map• Automatic sending of Health & Event notifications via email • Control locally via Front Panel Controls, USB Mouse or with the Included IR Remote control
• 2x RS-485 & 1x RS-232 for PTZ Control• MJPEG Streaming for easy integration with control systems
ConSIder THeSe oTHerGreaT ProduCTS froM
21
22 23
LIMITED PRODUCT WARRANTYVITEK products carry a three (3) year limited warranty. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user. This warranty is nontransferable and extends only to the original buyer or end user customer of a VITEK Authorized Reseller.
The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, caused by excessive voltage or lightning.
The product must not have been tampered with in any way or the guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact your local VITEK Reseller should servicing become necessary.
VITEK makes no warranty or guarantee whatsoever with respect to products sold or purchased through unauthorized sales channels. Warranty support is available only if product is purchased through a VITEK Authorized Reseller.
23
28492 Constellation Road ValenCia, Ca 91355WWW.ViteKCCtV.CoM
Version 1.0November 2015