Characterisation of a grooved heat pipe with an anodised ...
VOLUME III BOQ & PRICE BID -...
Transcript of VOLUME III BOQ & PRICE BID -...
TENDER DOCUMENT
NIT NO:- PAT/CON/720/01 DATED 17/02/2016
VOLUME – III
BOQ & PRICE BID
NAME OF WORK
CONSTRUCTION OF 5.00 LLPD DAIRY PLANT FROM GRID Y11 TO Y19
AT DEHRI-ON-SONE, BIHAR.
S. No. DSR No. DESCRIPTION OF ITEM Quantity UNIT RATE (Rs.) Amount
A CIVIL WORKSUB-HEAD -I: EARTH -WORK
1 2.6
Earth work in excavation by mechanical means (Hydraulic excavator)
/manual means over areas (exceeding 30cm in depth. 1.5 m in width as
well as 10 sqm on plan) including disposal of excavated earth, lead up to
50m and lift up to 1.5m, disposed earth to be levelled and neatly dressed.
2.6.1 All kinds of soil 1500.00 cum 155.60 233400
2 1.1.2Carriage of material By Mechanical Transport including loading,
unloading and stacking earth lead up to 5 km.983.13 cum 153.07 150487.7091
3 2.25
Filling available excavated earth (excluding rock) in trenches, plinth, sides
of foundations etc. in layers not exceeding 20cm in depth, consolidating
each deposited layer by ramming and watering, lead up to 50 m and lift
up to 1.5 m.
2808.00 cum 112.40 315619.2
4 N.S.-3
Supplying and filling in plinth with Local sand under floors, including
watering, ramming, consolidating and dressing complete. 3029.80 cum 804.00 2435959.2
Total 3135466.109
SUB-HEAD -II: CONCRETE WORK
5 4.1
Providing and laying in position cement concrete of specified grade
excluding the cost of centering and shuttering - All work up to plinth level :
4.1.81:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40
mm nominal size)393.57 cum 4301.15 1692803.606
6 4.13
Applying a coat of residual petroleum bitumen of grade of VG-10 of
approved quality using 1.7 kg per square metre on damp proof course
after cleaning the surface with brushes and finally with a piece of cloth
lightly soaked in kerosene oil.
393.57 sqm 132.00 51951.24
Total 1744754.846
SUB-HEAD -III : REINFORCED CEMENT CONCRETE
DESIGN MIX CONCRETE
7
Providing and laying in position machine batched and machine mixed
design mix M-20 grade cement concrete for reinforced cement concrete
work, using cement content as per approved design mix, including
pumping of concrete to site of laying but excluding the cost of centering,
shuttering, finishing and einforcement, including admixtures in
recommended proportions as per IS: 9103 to accelerate, retard setting of
concrete, improve workability without impairing strength and durability as
per direction of Engineer-in-charge.
NS-1 All works upto plinth level 641.80 cum 7212.00 4628661.6
NS-2 All works above plinth level upto floor V level 755.90 cum 7930.00 5994287
Total 10622948.6
FORM WORK
8 5.9Centering and shuttering including strutting, propping etc. and removal of
form for:
5.9.1 Foundations, footings, bases of columns, etc. for mass concrete 653.20 sqm 196.45 128321.14
5.9.5Lintels, beams, plinth beams, girders, bressumers and cantilevers
1050.00 sqm 332.15 348757.5
5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts 934.80 sqm 453.35 423791.58
5.9.3Suspended floors, roofs, landings, balconies and access
platform2343.70 sqm 401.65 941347.105
9 5.11
Extra for additional height in centering, shuttering where ever required
with adequate bracing, propping etc., including cost of de-shuttering and
decentering at all levels, over a height of 3.5 m, for every additional
height of 1 metre or part thereof (Plan area to be measured).
5.11.1Suspended floors, roofs, landing, beams and balconies (Plan
area to be measured) 159.05*1.5 = 238.581513.40 sqm 238.58 361059.405
Total 2203276.73
STEEL REINFORCEMENT
10 5.22
Steel reinforcement for R.C.C. work including straightening, cutting,
bending, placing in position and binding all complete up to plinth level.
5.22.6 thermo-mechnically treated bars 187913.14 kg 68.10 12796884.81
Total 12796884.81
MISCELLANEOUS
Enginerrinr Projects (I) Ltd
BILL OF QUANTITY : CIVIL , electrical , plumbing and other related works WORKS
5.00 LLPD DAIRY PLANT AT DEHRI ON SONE, BIHAR
FROM GRID Y11 TO Y19 OF DAIRY PLANT
Sub : Bill of Quantity
EPI 1 BOQ: CIVIL WORK
S. No. DSR No. DESCRIPTION OF ITEM Quantity UNIT RATE (Rs.) Amount
11 5.45
Providing and fixing of expansion joint system related with wall joint
internal/external) location as per drawings and direction of Engineer-n-
Charge. The joints shall be of extruded aluminium base embers,self
aligning /centering arrangement and support plates as per ASTM 221-
02. The material shall be such that it provides an Expansion Joints
System suitable for vertical wall to wall/ wall to corner Application, both
new and existing construction in office Buildings & complexes with no
slipping down tendency amongst the components of the Joint System.
The Joint System shall utilize light weight aluminium profiles exhibiting
minimal exposed aluminumsurfaces mechanically snap locking the
multicellular to facilitate movement.
5.45.1 Wall Joint of 100 mm gap 45.84 metre 5080.90 232908.456
12 5.46
Providing and fixing of expansion joint system of approved make and
manufactures for various roof locations as per approved drawings and
direction of Engineer-In-Charge. The joints shall be of extruded
aluminumbase members with, self aligning and self centering
arrangement support plates as per ASTM B221-02. The system shall be
such that it provides watertight roof to roof/roof to corner joint cover
expansion control system that is capable of accommodating
multidirectional seismic movement without stress to its components.
System shall consist of metal profile that incorporates a universal
aluminium base member designed to accommodate various project
conditions and roof treatments. The cover plate shall be designed of
width and thickness required to satisfy movement and loading
requirements and secured to base members by utilizing manufacturer's
pre-engineered self-centering arrangement that freely rotates / moves in
all directions. The Self centering arrangement shall exhibit circular sphere
ends that lock and slide inside the correspondingaluminum extrusion
cavity to allow freedom of movement and flexure in all directions
including vertical displacement. The Joint System shall resists damage or
deterioration from the impact of falling ice, expo sure to UV, airborne
contaminants and occasional foot traffic from maintenance personnel.
Provision of Moisture Barrier Membrane in the Joint System to have
water tight joint is mandatory requirement. Material shall confirm to ASTM
6063
.
5.46.1 Roof Joint of 100 mm gap 45.84 metre 6358.55 291475.932
Total 524384.388
SUB-HEAD -IV:BRICK WORK
11 6.1Brick work with common burnt clay F.P.S. (non modular brick) bricks of
class designation 100A .
6.1.2 Cement mortar 1:6 (1 cement : 6coarse sand) 136.99 cum 4677.25 640736.4775
13 6.4
Brick work with common burnt clay F.P.S. (non modular) bricks of class
designation 100A in superstructure above plinth level up to floor V level in
all shapes and sizes in :
6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) 754.27 cum 5426.15 4092782.161
14 6.12
Half brick masonry with common burnt clay F.P.S. (non modular) bricks
of class designation 100A in superstructure above plinth level up to floor
V level.
6.12.2 Cement mortar 1:4 (1 cement :4 coarse sand) 176.78 sqm 584.75 103372.105
15 6.15Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at
every third course of half brick masonry.176.78 sqm 69.50 12286.21
Total 4849176.953
SUB-HEAD-V : WOOD & PVC WORK
16 9.20
Providing and fixing ISI marked flush door shutters conforming to IS
:2202 (Part I) decorative type, core of block board construction with
frame of 1st class hard wood and well matched teak 3 ply veneering with
vertical grains or cross bands and face veneers on both faces of
shutters.
9.20.135 mm thick including ISI marked Stainless Steel butt hinges
with necessary screws109.20 sqm 2606.45 284624.34
17 9.21
Providing and fixing ISI marked flush door shutters conforming to IS
:2202 (Part I) non-decorative type, core of block board construction with
frame of 1st class hard wood and well matched commercial 3 ply
veneering with vertical grains or cross bands and face veneers on both
faces of shutters:
9.21.135 mm thick including ISI marked Stainless Steel butt hinges with
necessary screwssqm 1909.55
18 9.22
Extra for Providing and fixing flush doors with decorative veneering
instead of non decorative ISI marked flush door shutters conforming to
IS: 2202 (Part I)
9.22.1 On one side only sqm 394.90
19 9.83
Providing and fixing aluminium die cast body tubular type universal
hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on
the body, door weight upto 35 kg and door width upto 700 mm), with
necessary accessories and screws etc. complete.
each 753.75
Total 284624.34
ANODISED ALUMINIUM FITTINGS
EPI 2 BOQ: CIVIL WORK
S. No. DSR No. DESCRIPTION OF ITEM Quantity UNIT RATE (Rs.) Amount
20 9.96
Providing and fixing aluminium sliding door bolts, ISI marked anodised
anodic coating not less than grade AC 10 as per IS : 1868), transparent
or dyed to required colour or shade, with nuts and screws etc. complete :
9.96.1 300x16 mm 18.00 each 229.65 4133.7
21 9.97
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic
coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed
to required colour or shade, with necessary screws etc. complete :
9.97.1 300x10 mm 35.00 each 112.10 3923.5
22 9.100
Providing and fixing aluminium handles, ISI marked, anodised (anodic
coating not less than grade AC 10 as per IS : 1868) transparent or dyed
to required colour or shade, with necessary screws etc. complete :
9.100.1 125 mm 35.00 each 69.80 2443
9.101
Providing and fixing aluminium hanging floor door stopper, ISI marked,
anodised (anodic coating not less than grade AC 10 as per IS :
1868)transparent or dyed to required colour and shade, with necessary
screwsetc. complete.
9.101.2 Twin rubber stopper 18.00 each 83.95 1511.1
Total 12011.3
SUB-HEAD -VI:STEEL WORK
23 10.3
Providing and fixing in position collapsible steel shutters with vertical
channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size,
with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel
pulleys, complete with bolts, nuts, locking arrangement, stoppers,
handles, including applying a priming coat of approved steel primer.
17.64 sqm 5291.30 93338.532
24 10.6
Supplying and fixing rolling shutters of approved make, made of required
size M.S. laths, interlocked together through their entire length and jointed
together at the end by end locks, mounted on specially designed pipe
shaft with brackets, side guides and arrangements for inside and outside
locking with push and pull operation complete, including the cost of
providing and fixing necessary 27.5 cm long wire springs manufactured
from high tensile steel wire of adequate strength conforming to IS: 4454 -
part 1 and M.S. top cover of required thickness for rolling shutters.
10.6.1 80x1.25 mm M.S. laths with 1.25 mm thick top cover sqm 2142.10
25 10.7 Providing and fixing ball bearing for rolling shutters. each 438.95
26 10.28
Providing and fixing stainless steel ( Grade 304) railing made of Hollow
tubes, channels, plates etc., including welding, grinding, buffing, polishing
and making curvature (wherever required) and fitting the same with
necessary stainless steel nuts and bolts complete, i/c fixing the railing
with necessary accessories & stainless steel dash fasteners , stainless
steel bolts etc., of required size, on the top of the floor or the side of waist
slab with suitable arrangement as per approval of Engineer-in-charge,(
for payment purpose only weight of stainless steel members shall be
considered excluding fixing accessories such as nuts, bolts, fasteners
etc.).
497.71 kg 619.40 308281.574
Total 401620.106
SUB-HEAD -VII: FLOORING
27 NS-8
Provideing designation100 A one brick flat soling joints filled with local
sand including cost of watering, taxes, royailty all complete as per
building specification and direction of EPI
2222.55 sqm 222.00 493406.1
28 11.26
Kota stone slab flooring over 20 mm (average) thick base laid over and
jointed with grey cement slurry mixed with pigment to match the shade of
the slab, including rubbing and polishing complete with base of cement
mortar 1 : 4 (1 cement : 4 coarse sand) :
11.26.1 25 mm thick 607.28 sqm 1141.40 693149.392
11.27
Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars
laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3coarse
sand) and jointed with grey cement slurry mixed with pigment to match
the shade of the slabs, including rubbing and polishing complete.
123.40 sqm 1191.25 147000.25
29 11.36
Providing and fixing Ist quality ceramic glazed wall tiles conforming to
IS:15622 (thickness to be specified by the manufacturer), of approved
make, in all colours, shades except burgundy, bottle green, black of any
size as approved by Engineer-in-Charge, in skirting, risers of steps and
dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse
sand)and jointing with grey cement slurry @ 3.3kg per sqm, including
pointing in white cement mixed with pigment of matching shade complete.
1749.62 sqm 836.65 1463819.573
EPI 3 BOQ: CIVIL WORK
S. No. DSR No. DESCRIPTION OF ITEM Quantity UNIT RATE (Rs.) Amount
11.37
Providing and laying Ceramic glazed floor tiles of size 300x300
mm(thickness to be specified by the manufacturer) of 1st quality
conforming to IS : 15622 of approved make in colours such as White,
Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1
Cement : 4Coarse sand), including pointing the joints with white cement
and matching pigment etc., complete.
162.04 Sqm 785.40 127266.216
30 11.41
Providing and laying vitrified floor tiles in different sizes (thickness to be
specified by the manufacturer) with water absorption less than 0.08%and
conforming to IS : 15622, of approved make, in all colours and shades,
laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),
including grouting the joints with white cement and matching pigments
etc., complete.
11.41.2 Size of Tile 600x600 mm Sqm 1405.95
31 11.47
Providing and laying Vitrified tiles in different sizes (thickness to be
specified by the manufacturer), with water absorption less than 0.08%and
conforming to IS: 15622, of approved brand & manufacturer, in all
colours and shade, in skirting, riser of steps, laid with cement based high
polymer modified quick set tile adhesive (water based) conforming to IS:
15477, in average 6 mm thickness, including grouting of joints(Payment
for grouting of joints to bemadeseparately).
11.47.2 Size of Tile 600x600 mm sqm 1630.20
32 11.3
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate) finished with a floating coat of neat cement, including
cement slurry, but excluding the cost of nosing of steps etc. complete.55.09 sqm 353.35 19466.0515
11.3.1 40 mm thick with 20 mm nominal size stone aggregate
33 11.20
Chequerred precast cement concrete tiles 22 mm thick in footpath
&courtyard, jointed with neat cement slurry mixed with pigment to match
the shade of tiles, including rubbing and cleaning etc. complete, on 20mm
thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).
11.20.2Medium shade pigment using 50% white cement 50% Grey
cement120.00 sqm 1112.50 133500
34 N.S.-4
Mandana stone slab flooring over 20 mm (average) thick base laid over
and jointed with grey cement slurry mixed with pigment to match the
shade of the slab, including rubbing and polishing complete with base of
cement mortar 1 : 4 (1 cement : 4 coarse sand) :
25 mm thick 1988.00 sqm 2615.00 5198620
35 N.S.-5
Mandana stone slabs 20 mm thick in risers of steps, skirting, dado and
pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement:
3coarse sand) and jointed with grey cement slurry mixed with pigment to
match the shade of the slabs, including rubbing and polishing complete.
8.25 sqm 2696.00 22242
Total 8298469.583
SUB-HEAD -VII: ROOFING
36 12.1
Providing corrugated G.S. sheet roofing including vertical / curved
surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm
diameter with bitumen and G.I. limpet washers or with G.I. limpet washers
filled with white lead, including a coat of approved steel primer and two
coats of approved paint on overlapping of sheets complete (up to any
pitch in horizontal/ vertical or curved surfaces), excluding the cost of
purlins, rafters and trusses and including cutting to size and shape
wherever required.
12.1.1 1.00 mm thick with zinc coating not less than 275 gm/m² sqm 1030.50
ACCESSORIES
37 12.21
Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse
sand : 4 stone aggregate 10 mm and down gauge), including finishing
with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :269.42 metre 143.10 38554.002
Total 38554.002
SUB-HEAD -VIII:FINISHING
38 13.20
Pebble dash plaster up to 10 m height above ground level with a mixture
of washed pebble or crushed stone 6 mm to 12.5 mm nominal size,
dashed over and including fresh plaster in two layers under layer 12 mm
cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10 mm
cement plaster with cement mortar 1 : 3 (1 cement : 3 fine sand) mixed
with 10% finely grounded hydrated lime by volume of cement.
1585.39 sqm 394.65 625674.1635
CEMENT PLASTER (IN FINE SAND)39 13.1 12 mm cement plaster of mix :
13.1.2 1:6 (1 cement: 6 fine sand) 4897.68 sqm 149.45 731958.276
6 MM CEMENT PLASTER40 13.16 6 mm cement plaster of mix :
13.16.1 1:3 (1 cement: 3 fine sand) 2222.55 sqm 134.70 299377.485
41 13.46Finishing walls with WEATHER COAT Acrylic Smooth exterior paint of
required shade :
EPI 4 BOQ: CIVIL WORK
S. No. DSR No. DESCRIPTION OF ITEM Quantity UNIT RATE (Rs.) Amount
13.46.1
New work (Two or more coat applied @ 1.67 ltr/10 sqm over
and including priming coat of exterior primer applied @ 2.20
kg/ 10 sqm)
1585.39 sqm 90.00 142685.1
42 13.80
Providing and applying white cement based putty of average thickness1
mm, of approved brand and manufacturer, over the plastered wall
surface to prepare the surface even and smooth complete.7120.23 sqm 89.65 638328.6195
43 13.6Wall painting with acrylic emulsion paint of approved brand and
manufacture to give even shade
13.60.1 Two or more coats on new work 7448.75 sqm 89.70 668152.875
44 13.61Painting with synthetic enamel paint of approved brand and manufacture
to give even shade
13.61.1 Two or more coats on new work 109.20 sqm 74.40 8124.48
Total 3114300.999
SUB-HEAD-IX ALLUMINIUM WORK
45 21.1
Providing and fixing aluminium work for doors, windows, ventilators and
partitions with extruded built up standard tubular sections/ appropriate
Sections and other sections of approved make conforming to IS: 733
ands: 1285, fixing with dash fasteners of required dia and size, including
necessary filling up the gaps at junctions, i.e. at top, bottom and sides
with required EPDM rubber/ neoprene gasket etc. Aluminium sections
shall be smooth, rust free, straight, mitred and jointed mechanically
wherever required including cleat angle, Aluminium snap beading for
glazing / panelling, C.P. brass / stainless steel screws, all complete as
per architectural drawings and the directions of Engineer-in-charge.
21.1.2.2Powder coated aluminium (minimum thickness of powder
coating 50 micron)799.20 kg 435.75 348251.4
46 21.17
Providing and fixing anodised aluminium grill (anodised transparent or
dyed to required shade according to IS: 1868 with minimum anodic
coating of grade AC 15) of approved design/pattern, with approved
standard section and fixed to the existing window frame with C.P.brass/
stainless steel screws @ 200 mm centre to centre, including cutting the
grill to proper opening size for fixing and operation of handles and fixing
approved anodised aluminium standard section around the opening, all
complete as per requirement and direction of Engineer-in-charge. (Only
weight of grill to be measured for payment).
165.00 kg 403.35 66552.75
47 21.3
Providing and fixing glazing in aluminium door, window, ventilator
shutters and partitions etc. with EPDM rubber / neoprene gasket etc.
complete as per the architectural drawings and the directions of engineer-
in-charge.(Cost of aluminium snap beading shall be paid in basic item):
21.3.1 With float glass panes of 4.0 mm thickness 28.08 sqm 828.75 23271.3
Total 438075.45
SUB-HEAD -X:WATER PROOFING
48 22.15
Providing and laying in situ seven course water proofing treatment
withAPP (Atactic poly-propylene) modified Polymeric memberane over
roof consisting of first coat of bitumen primer @ 0.40 Kg per sqm, 2nd,
4th &6th courses of bonding material @ 1.20 Kg/sqm, which shall
consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd
and 5th layers of roofing membrane APP modified Polymeric membrane
1.5 mmthick of 2.25 Kg/sqm weight consisting of five layers prefabricated
with centre core as 20 micron HMHDPE film sandwiched on both sides
with polymeric mix and the polymeric mix is protected on both side with
20micron HMHDPE film. 7th, the top most layer shall be finished with
brick tiles of class designation 10 grouted with cement mortar 1:3
(1cement : 3fine sand) mixed with 2% integral water proofing compound
by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement
: 3 fine sand) and finished neat (item of laying brick tiles shall be paid for
separately).
2203.40 sqm 526.25 1159539.25
Total 1159539.25
49624087.47TOTAL PRICE FOR CIVIL WORK IN RS.
EPI 5 BOQ: CIVIL WORK
S. No. DSR No. DESCRIPTION OF ITEM Quantity UNIT RATE (Rs.) Amount
B INTERNAL PLUMBING & SANITRY WORKS
SANITARY INSTALLATIONS
1 17.10
Providing and fixing water closet squatting pan (Indian type W.C. pan )
with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C.
flushing cistern, including flush pipe, with manually controlled device
(handle lever) conforming to IS : 7231, with all fittings and fixtures
complete, including cutting and making good the walls and floors
wherever required
17.1.1White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with
integral type foot rests5 each 3392.80 16964
17.2.1Same as above for W.C. pan with ISI marked white solid plastic seat and
lid(European type W.C. pan)5 each 3317.30 16586.5
2 17.70
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass
pillar taps, 32 mm C.P. brass waste of standard pattern, including
painting of fittings and brackets, cutting and making good the walls
wherever require
17.7.4a) White Vitreous China Flat back wash basin size 550x 400 mm with
single 15 mm C.P. brass pillar tap pillar tap.25 each 1807.10 45177.5
3 17.11
Providing and fixing white vitreous china laboratory sink with C.I.
brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and
40mm C.P. brass trap with necessary C.P. brass unions complete,
including painting of fittings and brackets, cutting and making good the
wall wherever required :
17.11.1 Size 450x300x150 mm 2 each 2343.90 4687.8
4 17.10
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per
IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including
painting of fittings and brackets, cutting and making good the walls
wherever required
17.10.1.3 Kitchen sink with drain board of size 510x1040x200mm each 5966.15
5 17.28Providing and fixing flexible P.V.C. waste pipe for sink or wash basin
including PVC waste fittings complete.
17.28.2.1 32mm dia 6 each 74.45 446.7
17.28.2.2 40mm dia 40 each 76.75 3070
6 17.31
Providing and fixing 600x450 mm beveled edge mirror of superior glass
(of approved quality) complete with 6 mm thick hard board ground fixed
to wooden cleats with C.P. brass screws and washers complete. 10 each 793.95 7939.5
7 17.40
Providing and fixing white vitreous china flat back or wall corner type
lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes
respectively with automatic flushing cistern with standard flush pipe and
C.P. brass spreaders with brass unions and G.I clamps complete,
including painting of fittings and brackets, cutting and making good the
walls and floors wherever required
17.4.2Range of two urinal basins with 5 litre white P.V.C. automatic flushing
cistern10 each 5399.40 53994
8 17.71
Providing and fixing PTMT Liquid soap container 109 mm wide ,125 mm
high and 112 mm distance from wall of standard shape with bracket of
the same material with snap fittings of approved quality and colour
weighing not less than 105 gms
6 each 228.85 1373.1
9 NS-11Providing and Fixing C.P. brass Ablution health faucet assembly with 1.2
m long braided PVC hose with mounting bracket fixed on wall
complete.(for EWC)
10 each 500.00 5000
10 NS- 12Providing and Fixing C.P. brass Two way angle valve for ewc points &for
fixing ablution health faucet of approved quality conforming to is 8931.15
mm nominal bore.
10 each 600.00 6000
11 NS- 13 Providing and fixing Amul floor trap in floor. 80 each 1500.00 120000
SOIL WASTE & VENT PIPES AND FITTINGS
1 17.35 Providing & fixing soil, waste and vent pipes.
17.35.1 100 mm dia
17.35.1.2 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989
80 metre 917.75 73420
17.35.2 75mm diametre
17.35.2.2 Centrifugally cast (spun) iron socketed pipe as per IS: 3989 18 metre 791.30 14243.4
2 17.58Providing lead caulked joints to sand cast iron/centrifugally cast (spun)
iron pipes & fitting of diametres.
17.58.1 100mm 40 each 243.75 9750
17.58.2 75mm 8 each 205.30 1642.4
3 17.37
Providing & fixing M.S. holder bat clamps of approved design to sand
cast iron/centrifugally cast (Spun) iron S & S pipe embeded in & including
cement concrete blocks 10x10x10cm. of 1:2:4 mix (1 cement : 2 coarse :
4 graded stone aggregate 20mm nominal size). Including cost of cutting
holes & making good the walls etc.
17.37.1 For 100 mm dia pipe 12 each 152.90 1834.8
17.37.2 For 75 mm dia pipe 1 each 150.60 150.6
EPI 6 BOQ: CIVIL WORK
S. No. DSR No. DESCRIPTION OF ITEM Quantity UNIT RATE (Rs.) Amount
4 17.60Providing & fixing cast iron trap of self cleansing design with or without
vent arm complete, including cost of cutting & making good the walls &
floors.
17.60.2 100mm inlet & 75mm outlet.
17.60.2.1 Sand cast iron S&S as per IS - 3989 6 each 1020.90 6125.4
5 17.57 Providing and fixing collar :
17.57.1.2 100mm dia. 12 each 318.35 3820.2
17.57.2.2 75mm dia. 6 each 219.75 1318.5
6 17.39 Providing and fixing plain cast iron S & S sanitary bend.
17.39.1 100mm
17.39.1.2 Sand cast iron S&S as per IS : 3989 9 each 335.75 3021.75
17.39.2 75 mm dia
17.39.2.2 Sand cast iron S&S as per IS - 3989 1 each 248.80 248.8
7 17.38Providing and fixing bend of required degree with access door, insertion
rubber washer 3mm thick, bolts and nuts complete.
17.38.1 100 mm dia
17.38.1.2 Sand cast iron S&S as per IS - 3989 6 each 385.70 2314.2
17.38.2 75 mm dia
17.38.2.2 Sand cast iron S&S as per IS- 3989 1 each 318.50 318.5
8 17.44Providing and fixing centrifugally cast iron single equal plain junction of
required degree.
17.44.1 100x100x100 mm
17.44.1.2 Sand cast iron S&S as per IS - 3989 3 each 576.20 1728.6
17.44.2 75x75x75mm
17.44.2.2 Sand cast iron S&S as per IS - 3989 1 each 405.60 405.6
9 17.47Providing and fixing single unequal junction of required degree with
access door, insertion rubber washer 3 mm thick, bolts and nuts
complete :
17.47.1 100x100x75 mm
17.47.1.2 Sand cast iron S&S as per IS - 3989 2 each 792.20 1584.4
10 17.56 Providing and fixing cast iron terminal guard.
17.56.1 100mm
17.56.1.2 Sand cast iron S&S as per IS - 3989 3 each 434.50 1303.5
17.56.2 75 mm
17.56.2.2 Sand cast iron S&S as per IS - 3989 1 each 370.75 370.75
11 12.41
Providing and fixing on wall face unplasticised Rigid PVC rain water
pipes conforming to IS : 13592 Type A including jointing with seal ring
conforming to IS : 5382 leaving 10 mm gap for thermal expansion . (i)
Single socketed pipes.
12.41.2 110mm diametre 500 metre 231.65 115825
12 12.42
Providing and fixing on wall face unplasticised - PVC moulded fittings/
accessories for unplasticised Rigid PVC rain water pipes conforming to
IS : 13592 Type A, including jointing with seal ring conforming to IS :
5382, leaving 10 mm gap for thermal expansion.
12.42.3 Single tee with door
12.42.3.2 110x110x110 mm 25 each 306.60 7665
12.42.5.2 110 mm bend 90 each 161.55 14539.5
13 12.22
Making khurras 45x45 cm with average minimum thickness of 5 cm
cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400
micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse
sand) and a coat of neat cement,punning,rounding the edges and making
and finishing the outlet complete.
100 each 186.65 18665
14 12.43
Providing and fixing unplasticised -PVC pipe clips of approved design to
unplasticised - PVC rain water pipes by means of 50x50x50mm hard
wood plugs, screwed with M.S. screws of required length including cutting
brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand)
and making good the wall etc. complete.
12.43.2 110mm 200 each 189.05 37810
15 N.S.-14Supply &fixing 300 mm dia upvc SWR pipe along with necessary fittings
such as elbow bend ,tee including jointing with solution complete. 500 metre 750.00 375000
WATER SUPPLY PIPES AND FITTINGS
1 18.10Providing & fixing G.I. pipes complete with G.I. fittings & clamps including
cutting & making good the walls etc.
Internal work - Exposed on wall
18.10.3 25mm dia nominal bore (medium duty) 20 metre 304.15 6083
18.10.4 32mm dia nominal bore (medium duty) 10 metre 343.20 3432
18.11Concealed pipe including painting with anticorrosive bitumatic paint,
cutting chases and making good the wall.
18.11.1 15mm dia nominal bore 50 metre 306.05 15302.5
EPI 7 BOQ: CIVIL WORK
S. No. DSR No. DESCRIPTION OF ITEM Quantity UNIT RATE (Rs.) Amount
2 18.40Painting G.I. pipes and fittings with two coats of anti corrosive bitumastic
paint of approved quality.
18.40.1 15mm dia nominal bore. 27 metre 5.80 156.6
18.40.3 25mm dia nominal bore. 11 metre 8.75 96.25
18.40.4 32mm dia nominal bore. 8 metre 10.40 83.2
3 18.21Providing and fixing uplasticised PVC connection pipe with brass unions :
18.21.1 30 cm length
18.21.1.1 15 mm nominal bore 10 each 60.10 601
4 18.49Providing & fixing CP brass bib cock of approved quality conforming to IS
8931
18.49.1 15mm nominal bore 15 each 459.50 6892.5
5 18.51Providing & fixing C.P. brass long body bib cock of approved quality
conforming to IS standards and weighing not less than 690 gms.
18.51.1 15mm nominal bore 3 each 610.65 1831.95
6 18.17Providing and fixing gun metal gate valve with wheel of approved quality.
18.17.1 25mm dia nominal bore 3 each 428.85 1286.55
18.17.2 32mm dia nominal bore 3 each 501.50 1504.5
7 18.16 Providing and fixing brass stop cock of approved quality.
18.16.1 15 mm nominal bore 2 each 260.60 521.2
18.16.2 20 mm nominal bore 2 each 344.85 689.7
8 18.18Providing and fixing ball valve (brass) of approved quality, High or low
pressure, with plastic floats complete
18.18.3 25 mm nominal bore 2 each 449.95 899.9
9 18.48
Providing and placing on terrace (at all floor levels) polyethylene water
storage tank of approved brand and manufacture with cover and suitable
locking arrangement and making necessary holes for inlet, outlet and
overflow pipes but without fittings and the base support for tank.
Capacity 4000 litre(2*500+2*1000+1*1000=4000)2000
per
litre7.25 14500
INTERNAL SEWAGE
19.60
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes
with collars jointed with stiff mixture of cement mortar in the proportion of
1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :
19.6.3 250 mm dia. R.C.C. pipe 250 meter 468.60 117150
19.7.
Constructing brick masonry manhole with 100 class designation F.P.S.
bricks in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with
1:2:4 mix (1 cement : 2 coarse sand: 4graded stone aggregate 20mm
nominal size); foundation concrete 1:4:8 mix (1 cement :4 coarse sand:
8 graded stone aggregate 40mm nominal size) inside plastering 12mm
thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a
floating coat of neat cement and making channels in cement concrete
1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20mm
nominal size) finished with a floating coat of neat cement complete as per
standard design.
19.7.1Inside size 90x80 cm & 45cm deep including C.I. cover with frame (light
duty) total wt. of cover & frame to be not less than 38 Kg (wt. of cover 23
Kg & wt. of frame 15 Kg.
19.7.1.1With common burnt clay F.P.S. (non modular) bricks of class
designation 101 each 8507.00 8507
19.7.2
Inside size 120x90 cm and 90 cm deep including C.I. cover with
frame (medium duty) 500 mm internal diameter, total weight of
cover and frame to be not less than 116 kg (weight of cover 58
kg and weight of frame 58 kg) :
19.7.2.1With common burnt clay F.P.S. (non modular) bricks of class
designation 101 each 18304.45 18304.45
19.80 Extra for depth for manholes :
19.8.1 Size 90x80 cm
19.8.1.1With common burnt clay F.P.S. (non modular) bricks of class
designation101 meter 5638.20 5638.2
19.8.2 Size 120x90 cm
19.8.2.1With common burnt clay F.P.S. (non modular) bricks of
class designation 1025 meter 6753.65 168841.25
EPI 8 BOQ: CIVIL WORK
S. No. DSR No. DESCRIPTION OF ITEM Quantity UNIT RATE (Rs.) Amount
19.16
Providing orange colour safety foot rest of minimum 6mm thick plastic
encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS:
1786 having minimum cross section as 23 mm x25mm and over all
minimum length 263mm and width as 165mm with minimum 112mm
space between protruded legs having 2mm tread on top surface by
ribbing or chequering besides necessary and adequate anchoring
projections on tail length on 138 mm as per standard drawing and
suitable to with stand the bend test and chemical resistance test as per
specifications and having manufactures' permanent identification mark to
be visible even after fixing, including fixing in manholes with 30x20x15 cm
cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone
aggregate 20mm nominal size) complete as per design.
14 each 311.60 4362.4
19.40
Providing and fixing square-mouth S.W. gully trap class SP-1 complete
with C.I. grating brick masonry chamber with water tight C.I. cover with
frame o f 300 x300 mm size (inside) the weight of cover to be not less
than 4.50 kg and frame to be not less than 2.70 kg as per standard
design:
19.4.2 150 x 100 mm size P type
19.4.2.1With common burnt clay F.P.S. (non modular) bricks of
class designation 101 each 1594.35 1594.35
1352623.5TOTAL PRICE FOR INTERNAL PLUMBING & SANITRY WORKS IN RS.
EPI 9 BOQ: CIVIL WORK
S. No. DSR No. DESCRIPTION OF ITEM Quantity UNIT RATE (Rs.) Amount
C ELECTRICAL WORKSSUB-HEAD - I : INTERNAL WIRING
1
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm
FR PVC insulated copper conductor single core cable in surface / recessed
medium class PVC conduit, with modular switch, modular plate, suitable GI
box and earthing the point with 1.5 sq.mm. FR PVC insulated copper
conductor single core cable etc as required
a)DSR-2014-
1.10.3
Group -C250 Point 718.00 179500
2Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of
FR PVC insulated copper conductor, single core cable in surface/ recessed
medium class PVC conduit as required
a)DSR-2014-
1.14.2
2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire1245 Metre 131.00 163095
b)DSR-2014-
1.14.3
2 X 4 sq. mm + 1 X 4 sq. mm earth wire722 Metre 162.00 116964
c)DSR-2014-
1.14.4
2 X 6 sq. mm + 1 X 6 sq. mm earth wire748 Metre 221.00 165308
d)DSR-2014-
1.14.9
4 x 6 sq.mm + 2 x 6 sq.mm. earth wire25 Metre 389.00 9725
d)DSR-2014-
1.14.10
4 x 10 sq.mm + 2 x 10 sq.mm. earth wire35 Metre 597.00 20895
d)DSR-2014-
1.14.11
4 x 16 sq.mm + 2 x 16 sq.mm. earth wire35 Metre 883.00 30905
3DSR-2014-
1.31
Supplying and fixing suitable size GI box with modular plate and cover in front
on surface or in recess, including providing and fixing 3 pin 5/6 amps modular
socket outlet and 5/6 amps modular switch, connection etc. as required. (For
light plugs to be used in non residential buildings).
18 Each 303.00 5454
4DSR-2014-
1.32
Supplying and fixing suitable size GI box with modular plate and cover in front
on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps
modular socket outlet and 15/16 amps modular switch, connection etc. as
required.
65 Each 395.00 25675
5DSR-2014-
2.19
Supplying and fixing 20 amps, 415 volts, TPN industrial type, socket outlet,
with 4 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve,
TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal
cover for the socket out let and complete with connections, testing and
commissioning etc. as required.
4 Each 1967.00 7868
6DSR-2013-
2.20
Supplying and fixing 30 amps, 415 volts, TPN industrial type, socket outlet,
with 4 pole and earth, metal enclosed plug top along with 30 amps "C" curve,
TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal
cover for the socket out let and complete with connections, testing and
commissioning etc. as required.
11 Each 2473.00 27203
7Supplying and fixing of following sizes of medium class PVC conduit along with
accessories in surface/recess including cutting the wall and making good the
same in case of recessed conduit as required.
a)DSR-2014-
1.21.1
20mm dia PVC conduit154 Metre 53.00 8162
b)DSR-2014-
1.21.2
25mm dia PVC conduit92 Metre 65.00 5980
c)DSR-2014-
1.21.3
32mm dia PVC conduit61 Metre 85.00 5185
SUB-HEAD II - FANS & LIGHT FIXTURES:
1NS-INEL-
5B
Supplying, fixing, connecting, testing and commissioning of surface mounted 1
x 28 watt T-5 fluorescent luminaire complete with electronic ballast, lockable
holders and fluorescent lamp including connection etc. as required similar to
Bajaj cat no. BTIR 1x28W T-5 or equivalent
80 Each 1109.00 88720
2NS-INEL-
5C
Supplying, fixing, connecting, testing and commissioning of surface mounted 2
x 28 watt T-5 fluorescent luminaire complete with electronic ballast, lockable
holders and fluorescent lamp including connection etc. as required similar to
Bajaj cat no. BTIR 2x28W T-5 or equivalent
100 Each 1562.00 156200
3 NS-INEL-5E
Supplying, fixing, connecting, testing and commissioning of surface mounted 1
x 11 watt fluorescent luminaire complete with electronic ballast, lockable
holders and fluorescent lamp including connection etc. as required similar to
Philips cat no. FCS0100 1XPL13WI24V
7 Each 1378.00 9646
6 NS-INEL-5F
Supplying, fixing, connecting, testing and commissioning of Bulkhead type light
fitting complete with , wire guard, holder, electronic ballast 1 x 6 W lamp
including connections etc. as required similar to Philips Cat. No. Endura LED or
equivalent
2 Each 3508.00 7016
7 NS-INEL-5K
Supplying, fixing, connecting, testing and commissioning of mirror light
luminaire with 1 x 14 watt complete with electronic ballast, lamp including
connection etc. complete as required similar to Philips Cat. No. FWZ 300 or
equivalent
5 Each 3089.00 15445
EPI 10 BOQ: CIVIL WORK
S. No. DSR No. DESCRIPTION OF ITEM Quantity UNIT RATE (Rs.) Amount
8 NS-INEL-5J
Supply, installation, connecting, testing and commissioning of illuminated exit
sign with 1 x 6 watt LED lamp including providing maintenance free batteries &
charger capable of working for 2 hr duration mounted on ceiling/wall complete
with the approved EXIT self adhesive labels as per site requirement as required
similar to Bajaj or equivalent
4 Each 5576.00 22304
10NS-INEL-
5N
Supply, installation, connecting, testing and commissioning of Motion sensor
including all wiring in the existing conduits required similar to Philips cat no.
occuswitch
5 Each 4608.00 23040
11NS-INEL-
5N
Supplying, fixing, connecting, testing and commissioning of
Highbay/mediumbay luminaire light complete with , wire guard, holder,
electronic ballast 1 x 50 W Sodium Vapour lamp including connections etc. as
required similar to Bajaj Cat. No BJHBI 150 SV
40 Each 3387.00 135480
12
Supplying, erection, connecting, testing and commissioning of following size
exhaust fan complete with gravity louver and connection with 3 core flexible
wire as required.
NS-INEL-
5N
c) 450mm 900 RPM12 Each 3696.00 44352
13NS-INEL-
5O
Supplying, Installation, Testing & Commissioning of Energy efficient, five star,
rating 1200mm size ceiling fan including suitable size down rod blade canopy
etc. as required suitable for operation Three phase 415 volt 50 cycle per
second. AC supply including wiring the down rods of standard length (upto 30
cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core
cable, including earthing and providing and fixing phenolic laminated sheet
cover on the fan box etc. as required. Make Usha/Crompton
Greaves/Bajaj/Havells
30 Each 1698.00 50940
SUBHEAD- III: M.V. PANELS/ DISTRIBUTION BOARD
1
Supplying and fixing following way prewired vertical type TP&N MCB
distribution board of steel sheet for 415 volts on surface/ recess complete with
loose wire box of sheet steel, dust protected, duly powder painted, inclusive of
200 amps tinned copper bus bar, common neutral link, earth bar, din bar for
mounting MCB's, terminal connectors for all incoming and outgoing circuits,
duly prewired with adequate size of FR PVC insulated copper conductor upto
the terminal connector/ neutral link, earthing etc as required (But without MCB/
RCCB/ Isolator). (Note : Prewired vertical type MCB TPDB is normally used
where 3 phase outlets are required.)
a)DSR-2014-
2.9.7
8 way Double door4 Nos. 11123.00 44492
b)DSR-2014-
2.9.8
12 way Double door1 Nos. 14768.00 14768
2Supplying and fixing following rating, four pole, 415 volts, isolator in the
existing MCB DB complete with connections, testing and commissioning etc.
as required.
a)DSR-2014-
2.13.2
63 amps4 Nos. 670.00 2680
3
Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve,
miniature circuit breaker suitable for inductive load of following poles in the
existing MCB DB complete with connections, testing and commissioning etc.
as required.
a)DSR-2014-
2.10.1
Single pole110 Nos. 169.00 18590
4
Supplying, installation, testing and commissioning of L.T. panel fully
compartmentalized cubical type sheet clad floor mounted totally enclosed ,
extensible on both sides, switch board suitable for use on 415 Volts 3-phase, 4
wire, 50 Hz system having required fault capacity, housed with incoming and
outgoing, Aluminium bus bars with current rating of 0.8 Amp/sq.mm,
interconnection etc. with indication lamps, accessories etc, as required as per
specification and schematic diagram as required. (MAIN PANEL)
INCOMER:-
1 Nos. 400 Amps. TPN MCCB(25 KA) with electronic releases.
1 Set phase indication lights (R, Y, B)
1 No. Volt Meter (digital type) with inbuilt VSS & control fuses.
1 No. 0-400 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:-
630 Amps. TPN Aluminium bus bars (25 KA)OUT GOINGS:-
1 Nos. 200 Amps. TPN MCCB(35 KA) with electronic releases.
4 Nos. 100 Amps. TPN MCCB(25 KA) with electronic releases.
NS-INEL-
4M
4 Nos. 63 Amps. TPN MCCB(25 KA) with electronic releases.1 Set 104243.00 104243
5Same as above item no. -4 but following mountings. (Sub panel For Main
Plant) INCOMER:-
1 Nos. 200 Amps. TPN MCCB(25 KA) with electronic releases.
1 Set phase indication lights (R, Y, B)
1 No. Volt Meter (digital type) with inbuilt VSS & control fuses.
1 No. 0-200 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:-
300 Amps. TPN Aluminium bus bars (25 KA)
EPI 11 BOQ: CIVIL WORK
S. No. DSR No. DESCRIPTION OF ITEM Quantity UNIT RATE (Rs.) Amount
OUT GOINGS:-
6 Nos.63A TPN, MCB (10KA).
NS-INEL-
4N
6 Nos.40A TPN, MCB (10KA).1 Set 71667.00 71667
6Same as above item no. -4 but following mountings. (Sub panel For Office)
INCOMER:-
1 Nos. 100 Amps. TPN MCCB(25 KA) with electronic releases.
1 Set phase indication lights (R, Y, B)
1 No. Volt Meter (digital type) with inbuilt VSS & control fuses.
1 No. 0-100 Amp. Ammeter (digital type) with inbuilt ASS
BUS BARS:-
200 Amps. TP&N Aluminium bus bars (25 KA)
OUT GOINGS:-
3 Nos.63A TPN, MCB (10KA).
NS-INEL-4K3 Nos.40A TPN, MCB (10KA).
1 Set 65152.00 65152
7Same as above item no. - 4 but following mountings. (Sub panel For service
Block)
INCOMER:-
1 Nos. 63 Amps. TPN MCCB(25 KA) with electronic releases.
1 Set phase indication lights (R, Y, B)
1 No. Volt Meter (digital type) with inbuilt VSS & control fuses.
1 No. 0-63 Amp. Ammeter (digital type) with inbuilt ASS BUS BARS:-
200 Amps. TP&N Aluminium bus bars
OUT GOINGS:-
2 Nos. 63 Amps. TPN MCB(10 KA)
NS-INEL-
4O
2 Nos. 32A TPN, MCB (10KA).1 Set 52121.00 52121
8DSR-2014-
2.21
Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of
mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and
with inscription in single red colour on front side as required.4 Each 141.00 564
SUB-HEAD -lV : EARTHING
1DSR-2014-
5.4
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including
accessories, and providing masonry enclosure with cover plate having locking
arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and
salt as required.
2 Each 4490.00 8980
2DSR-2014-
5.6
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including
accessories, and providing masonry enclosure with cover plate having locking
arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and
salt as required.
1 Each 9292.00 9292
3DSR-2014-
5.8
Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground
as strip earth electrode, including connection/ terminating with nut, bolt, spring,
washer etc. as required. (Jointing shall be done by overlapping and with 2 sets
of brass nut bolt & spring washer spaced at 50mm)
3 Metre 753.00 2259
4DSR-2014-
5.9
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as
strip earth electrode, including connection/ terminating with G.I. nut, bolt,
spring, washer etc. as required. (Jointing shall be done by overlapping and
with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
16 Metre 109.00 1744
5DSR-2014-
5.10
Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from
earth electrode including connection with brass nut, bolt, spring, washer
excavation and re-filling etc. as required.
60 Metre 1082.00 64920
6DSR-2014-
5.11
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth
electrode including connection with G.I. nut, bolt, spring, washer excavation
and re-filling etc. as required.
8 Metre 421.00 3368
7DSR-2014-
5.12
Providing and laying earth connection from earth electrode with 6 SWG dia
G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with
G.I. thimble excavation and re-filling as required.
612 Metre 151.00 92412
8DSR-2014-
5.14
Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for
connections etc. as required. 20 Metre 856.00 17120
9DSR-2013-
5.15
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for
connections etc. as required. 20 Metre 133.00 2660
SUB HEAD-V : T.V. , TELEPHONE SYSTEM & LAN SYSTEM
1Supplying and drawing following pair 0.5 sq mm FR PVC insulated annealed
copper conductor, unarmored telephone cable in the existing surface/
recessed steel/ PVC conduit as required.
a)DSR-2014-
1.18.3
4 Pair (8 core)Metre 27.00
b)DSR-2014-
1.18.2
2 Pair (4 core)600 Metre 18.00 10800
EPI 12 BOQ: CIVIL WORK
S. No. DSR No. DESCRIPTION OF ITEM Quantity UNIT RATE (Rs.) Amount
2
Providing, laying, connecting and testing of multi-core telephone armoured
cable of conductor size 0.63mm dia annealed copper conductor PVC insulated
PVC sheathed jelly filled (as per DOT specification) cable along wall or ceiling or
through existing pipe.
a)NS-INEL-
4B
20 Pair telephone cable25 Metre 199.00 4975
b)NS-INEL-
4D
5 Pair telephone cableMetre 100.00
3
Providing, fixing connecting and testing of under noted size of solderless
telephone tag block Krone make in surface/recess in wall required size of M.S.
box with hinged lockable cover duly stove enamel painted.
a)NS-INEL-
4G
5 pair tag blockEach 1473.00
b)NS-INEL-
4H
20 pair tag block1 Each 1878.00 1878
4
Supplying and fixing of following sizes of PVC conduit along with the
accessories in surface / recess including cutting the wall and making good the
same in case of recessed conduit as required as per specification.
a)DSR-2014-
1.21.1
20mm dia PVC conduit90 Metre 53.00 4770
b)DSR-2014-
1.21.2
25mm dia PVC conduit62 Metre 65.00 4030
c)DSR-2014-
1.21.3
32mm dia PVC conduit20 Metre 85.00 1700
5DSR-2014-
14.13.2
Providing, laying and fixing following dia G.I. pipe (medium class) in ground
complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as
required
12 Metre 697.00 8364
6DSR-2014-
1.24.6
Supplying and fixing Telephone socket outlet modular switch/ socket on the
existing modular plate & switch box including connections but excluding
modular plate etc. as required.
13 Each 95.00 1235
7DSR-2014-
1.24.7
Supplying and fixing TV antenna socket outlet modular switch/ socket on the
existing modular plate & switch box including connections but excluding
modular plate etc. as required.
1 Each 94.00 94
8DSR-2014-
1.19
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper
conductor PE insulated, shielded with fine tinned copper braid and protected
with PVC sheath in the existing surface/ recessed steel/ PVC conduit as
required.
25 Metre 28.00 700
9 NS-INEL-4KSupplying and fixing M.S. box with Phenolic laminate plate 4- way splitter box
for TV antenna complete as required.6 Each 211.00 1266
10 NS-INEL-4LSupplying and fixing M.S. box with modular type data/ computer (RJ-45) outlet
complete as required.6 Each 365.00 2190
11NS-INEL-
4M
Providing, laying, connecting and testing of data/ computer Cat-6 cable along
wall or ceiling or through existing pipe, including penta scanning
documentation etc as required.
16 Metre 64.00 1024
12NS-INEL-
4N
Supplying and fixing of 450 x 450 x 150 M.S. box with Phenolic laminate plate
of 16 SWG M.S. Sheet with hinged door cover for mounting TV amplifier
including wooden base plate complete as required.4 Each 530.00 2120
1947240
52923950.97TOTAL PRICE FOR CIVIL WORK, INTERNAL PLUMBING WORKS, SANITARY WORKS &
ELECTRICAL WORKS IN RS.
TOTAL PRICE FOR ELECTRICAL WORKS IN RS.
EPI 13 BOQ: CIVIL WORK
SL.NO HEAD AMOUNT (DSR)
a HEAD A: CIVIL WORKS
1a SUB-HEAD-1, EARTH WORK ` 31,35,466.109
1b SUB-HEAD-2, CONCRETE WORK ` 17,44,754.846
1c SUB-HEAD-3, RCC WORK ` 2,61,47,494.532
1d SUB-HEAD-4, BRICK WORK ` 48,49,176.953
1e SUB-HEAD-5, WOOD WORK ` 2,96,635.640
1f SUB-HEAD-6, STEEL WORK ` 4,01,620.106
1g SUB-HEAD-7, FLOORING WORK & ROOFING ` 83,37,023.582
1h SUB-HEAD-8, FINISHING. ` 31,14,300.999
1i SUB-HEAD-9, ALLUMINIUM WORK ` 4,38,075.450
1j SUBHEAD-10 , WATER PROOFING ` 11,59,539.250
SUB-TOTAL ( A) ` 4,96,24,087.47
bHEAD B: SANITARY, WATER SUPPLY & SEWERAGE
WORKS` 13,52,623.50
c HEAD C : ELECTRICAL( INTERNAL LIGHTENING) ` 19,47,240.00
TOTAL ESTIMATED COST ` 5,29,23,950.97
ENGINEERING PROJECTS (I) LTD
ABSTRUCT OF COST FOR CONSTRUCTION OF 5.00 LLPD DAIRY PLANT FROM GRID Y11 TO
Y19 AT DEHRI-ON-SONE, BIHAR.
Sub : ABSTRUCT OF COST
(Rupees Five Crores Twenty Nine Lakhs Twenty Three Thousand Nine Hundred Fifty and Ninty Seven paisa Only)
MAIN DAIRY PLANT FRON GRID Y11 TO Y19
TOTAL ESTIMATED COST FOR 5.00 LLPD DAIRY PLANT FROM GRID Y11 TO Y19 :
Tender enquiry No. PAT/CON/720/001 DATED 17/02/2016
In figures In words In figures In words
1
CIVIL, ELECTRICAL,
PLUMBING AND OTHER
RELATED WORKS FOR
CONSTRUCTION OF 5.00
LLPD DAIRY PLANT FROM
GRID Y11 TO Y19 AT DEHRI-
ON-SONE ,BIHAR.
BIDDER'S FINANCIAL OFFER : Rs. (In Figure)
;
Rupees (In Words)
SEAL
BIDDER'S PRICE
% QUOTE ABOVE / AT PAR/ BELOW
PROJECT: CONSTRUCTION OF 5.00 LLPD DAIRY PLANT FROM GRID Y11 TO Y19 AT DEHRI-ON-SONE, BIHAR.
Engineering Projects (I) ltd
Rs. 52923950/ -
(Rupees Five Crores
Twenty Nine Lakhs
Twenty Three Thousand
Nine Hundred Fifty Only)
Price Bid
QUOTATION SHEETS
AMOUNT IN Rs. After adding percentage above, at par or belowSL. No. DESCRIPTION ESTIMATED COST (IN
Rs.)